The bit-2-doorbell reset method seemed to cause (survivable) NMIs
on some systems and (unsurvivable) IOCK NMIs on some G7 servers.
Firmware guys implemented a new doorbell method to alleviate these
problems triggered by bit 5 of the doorbell register. We want to
use it if it's available.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Detect failure of controller reset by noticing if the 32 bytes of
"driver version" we store on the hardware in the config table
fail to get zeroed out. Previously we noticed if the controller
did not transition to "simple mode", but this did not detect reset
failure if the controller was already in simple mode prior to
the reset attempt (e.g. due to module parameter hpsa_simple_mode=1).
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Controller will transfer only 32-bits on completion if it
knows we are only using 32-bit tags. Also, some newer controllers
apparently (and erroneously) require that we only use 32-bit tags,
and that we inform the controller of this.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver's internal queues should be FIFO, not LIFO.
This is a port of an almost identical patch from cciss by Jens Axboe.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some low bits might have been set by the driver, causing
a message like this to come out:
[ 13.288062] ------------[ cut here ]------------
[ 13.293211] WARNING: at lib/dma-debug.c:803 check_unmap+0x1a1/0x654()
[ 13.300387] Hardware name: ProLiant DL180 G6
[ 13.305335] hpsa 0000:06:00.0: DMA-API: device driver tries to free
DMA memory it has not allocated [device address=0x000000007f81e001]
[size=640 bytes]
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Smart Array controllers newer than the P600 do not honor the
PCI power state method of resetting the controllers. Instead,
in these cases we can get them to reset via the "doorbell" register.
This escaped notice until we began using "performant" mode because
the fact that the controllers did not reset did not normally
impede subsequent operation, and so things generally appeared to
"work". Once the performant mode code was added, if the controller
does not reset, it remains in performant mode. The code immediately
after the reset presumes the controller is in "simple" mode
(which previously, it had remained in simple mode the whole time).
If the controller remains in performant mode any code which presumes
it is in simple mode will not work. So the reset needs to be fixed.
Unfortunately there are some controllers which cannot be reset by
either method. (eg. p800). We detect these cases by noticing that
the controller seems to remain in performant mode even after a
reset has been attempted. In those case, we proceed anyway,
as if the reset has happened (and skip the step of waiting for
the controller to become ready -- which is expecting it to be in
"simple" mode.) To sum up, we try to do a better job of resetting
the controller if "reset_devices" is set, and if it doesn't work,
we print a message and try to continue anyway.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch removes unnecessary #define's from hpsa. The SCSI midlayer
handles all this for us.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This uses the scatter-gather chaining feature of Smart Array
controllers. 32 scatter-gather elements are embedded in the
"command list", and the last element in the list may be marked
as a "chain pointer", and point to an additional block of
scatter gather elements. The precise number of scatter gather
elements supported is dependent on the particular kind of
Smart Array, and is determined at runtime by querying the
hardware.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is done by adding support for the so-called "performant mode"
(that's really what they called it). Smart Array controllers
have a mode which enables multiple command completions to be
delivered with a single interrupt, "performant" mode. We want to use
that mode, as some newer controllers will be requiring this mode.
Signed-off-by: Don Brace <brace@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
That is, use u64, u32, u16 and u8 rather than __u64, __u32, __u16 and __u8.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This driver supports a subset of HP Smart Array Controllers.
It is a SCSI alternative to the cciss driver.
[akpm@linux-foundation.org: avoid helpful cleanup patches]
[achiang@hp.com: make device attrs static]
[akpm@linux-foundation.org: msleep() does set_current_state() itself]
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron