Several minor issues exist in the low-level device handling code of
e1000. The NVM and EEPROM writing/reading code was updated which fixes
unneeded delays, adds proper eeprom aqcuiring steps and handle shadow
ram and flash access. Minor cosmetic adjustments to the polarity code
adding symbols. PHY reset code mistakenly distinguished between MAC
types instead of PHY types, and was fixes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We were plagued by our interrupt handler posting a watchdog event which
could occur when our adapter was going down in case a late packet arrived
just before e1000_down() finished. This caused the watchdog timer to start
after the NIC was down and keep rescheduling it every N seconds. Once
the driver unloaded it would panic.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Manageability is using one more RAR entry than we anticipated earlier
for ICH8.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add code to display the detected PCI-E bus width.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
When powering down the PHY (if WoL is disabled) we should only check
copper PHY's and handle PCI-E adapters differently.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several hardware bits were set all over the driver and have been
consolidated into a single function.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Disable jumbo frames for 82573L alltogether and when ASPM is enabled
since the hardware has problems with it. For the NICs that do support
this in the 82573 series we set ERT_2048 to attempt to receive as much
traffic as early as we can.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Several manageability capability detection parts hinted towards
our code being incomplete for PCI-E. According to spec, we do not
want to poke any MANC bits at all.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
With a patch, ethtool can now signify the driver to advertise more
than just a single speed/duplex setting. This allows you to tell the
card to advertise in 10/100 in any speed if you don't have a gigabit
switch for instance.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Add 4 multicast and broadcast hardware counters (rx/tx), and eliminate
as many non-hardware counters as possible.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Unify our shutdown/suspend/resume code and make it similar to e1000:
e1000_shutdown now calls suspend which does the exact same thing on
shutdown except saving PCI config state on suspend. WoL setup code
is now also more simple and works even when CONFIG_PM is not set, which
was previously broken.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
We keep getting requests from people that think that this might be
an exploitable hole where we would overwrite 4 bytes in the netdev
struct if the pci name would exceed 15 characters. In reality this
will never happen but we fix it anyway.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This update to the copyright header adds the mailinglist, and aligns it
with the kernel licensing as well as remove the offending 'all rights
reserved'.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This patch removes accesses to the HDLC-internal data structures
from pc300 driver, thus enabling it to compile but breaking part
of its functionality.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch enables building of individual WAN protocol support
routines (parts of generic HDLC) as separate modules.
All protocol-private definitions are moved from hdlc.h file
to protocol drivers. User-space interface and interface
between generic HDLC and underlying low-level HDLC drivers
are unchanged.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hack uart_suspend_port() and uart_resume_port() so that serial console
ports are not suspended if CONFIG_DISABLE_CONSOLE_SUSPEND is set.
This makes it possible to debug the suspend and resume routines of all
device drivers as well as the lowest-level swsusp code with the help of the
serial console.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The third argument of au1xxx_dbdma_chan_alloc's callback function is not
used anywhere.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the atomic counter for slab_reclaim_pages and replace the counter
and NR_SLAB with two ZVC counter that account for unreclaimable and
reclaimable slab pages: NR_SLAB_RECLAIMABLE and NR_SLAB_UNRECLAIMABLE.
Change the check in vmscan.c to refer to to NR_SLAB_RECLAIMABLE. The
intend seems to be to check for slab pages that could be freed.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not display HIGHMEM memory sizes if CONFIG_HIGHMEM is not set.
Make HIGHMEM dependent texts and make display of highmem counters optional
Some texts are depending on CONFIG_HIGHMEM.
Remove those strings and remove the display of highmem counter values if
CONFIG_HIGHMEM is not set.
[akpm@osdl.org: remove some ifdefs]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NetLabel]: update docs with website information
[NetLabel]: rework the Netlink attribute handling (part 2)
[NetLabel]: rework the Netlink attribute handling (part 1)
[Netlink]: add nla_validate_nested()
[NETLINK]: add nla_for_each_nested() to the interface list
[NetLabel]: change the SELinux permissions
[NetLabel]: make the CIPSOv4 cache spinlocks bottom half safe
[NetLabel]: correct improper handling of non-NetLabel peer contexts
[TCP]: make cubic the default
[TCP]: default congestion control menu
[ATM] he: Fix __init/__devinit conflict
[NETFILTER]: Add dscp,DSCP headers to header-y
[DCCP]: Introduce dccp_probe
[DCCP]: Use constants for CCIDs
[DCCP]: Introduce constants for CCID numbers
[DCCP]: Allow default/fallback service code.
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SOUND] sparc/amd7930: Use __devinit and __devinitdata as needed.
[SUNLANCE]: Mark sparc_lance_probe_one as __devinit.
[SPARC64]: Fix section-mismatch errors in solaris emul module.
The v4l2 API documentation for VIDIOC_ENUMSTD says:
To enumerate all standards applications shall begin at index
zero, incrementing by one until the driver returns EINVAL.
The actual code, however, tests the index this way:
if (index<=0 || index >= vfd->tvnormsize) {
ret=-EINVAL;
So any application which passes in index=0 gets EINVAL right off the bat
- and, in fact, this is what happens to mplayer. So I think the
following patch is called for, and maybe even appropriate for a 2.6.18.x
stable release.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Seems like not all drivers use the framebuffer_alloc() function and won't
have an initialized mutex. But those don't have a backlight, anyway.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Olaf Hering <olaf@aepfle.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Daniel R Thompson <daniel.thompson@st.com>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At enslavement time, the primary slave might not be activated if
there is already an active slave and the new slave is the primary.
Replaced complicated logic with a call to bond_select_active_slave(),
which does the right thing.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6378
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed handling of 802.3ad LACPDUs. Do not byte swap data in
place in the packet. Updated nomenclature of "__ntohs_lacpdu" to be
"htons"; it was previously used for both ntohs and htons operations, but
only called ntohs functions.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add logic to check ARP request / reply packets used for ARP
monitor link integrity checking.
The current method simply examines the slave device to see if it
has sent and received traffic; this can be fooled by extraneous traffic.
For example, if multiple hosts running bonding are behind a common
switch, the probe traffic from the multiple instances of bonding will
update the tx/rx times on each other's slave devices.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When a bonding netdevice is admin-ed down it loses the slaves
attributes (set via ifenslave). This is not consistent with other
behavior of netdevices (example a qdisc attached to a netdevice doesnt
disappear or an attached IP address etc).
The included patch fixes this. Ive tested by ifenslaving, downing the
bond, checking /proc and making sure it still has the slaves, up-ing the
bond and making sure things continue to work.
Jay/Bonding folks if you are ok with it, just ACK it or include it in
your tree etc. Otherwise we can discuss.
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add priv_flag to specifically identify bonding-involved devices. Needed
because IFF_MASTER is an unreliable identifier (vlan interfaces above bonding
will inherit IFF_MASTER). Misidentification of devices would cause
notifier events for other devices to be erroneously processed by bonding,
causing various havoc.
Bug discovered by Martin Papik <martin.papik@ipsec.info>; this patch is
modified from his original.
Signed-off-by: Martin Papik <martin.papik@ipsec.info>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The bonding driver fails to adjust its hard_header_len when enslaving
interfaces. Whenever an interface with a hard_header_len greater than the
ETH_HLEN default is enslaved, the potential for an oops exists, and if the
oops happens while responding to an arp request, for example, the system
panics. GIANFAR devices may use an extended hard_header for VLAN or
hardware checksumming. Enslaving such a device and then transmitting over
it causes a kernel panic.
Patch modified from submitter's original, but submitter agreed with this
patch in private email.
Signed-off-by: Mark Huth <mhuth@mvista.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unneeded test for NULL. Reported by Thomas Dillig
<tdillig@stanford.edu> and Isil Dillig <isil@stanford.edu> via Stephen
Hemminger <shemminger@osdl.org>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Though link_failure_count is type unsigned int, this value is outputted to
/proc/net/bonding/bondX file using "%d" instead of "%u".
The attached patch fixes this problem.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The value of "downdelay/miimon" and "updelay/miimon" are stored in
slave->delay. The type of downdelay, updelay, and miimon are all int.
However, slave->delay is type short, and it is not possible to store the
value of "downdelay/miimon" or "updelay/miimon" in some cases. (For example,
miimon=1 downdelay=32768)
The attached patch fixes this problem.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow channel bonding to enslave a 10 Gig adapter without errors.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linas Vepstas