POWER7 has the same PR/HV bit layout as POWER6, so set the flag.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: a.p.zijlstra@chello.nl
Cc: benh@kernel.crashing.org
LKML-Reference: <20090701030701.GI3563@kryten>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use "ceu0" and "ceu1" as CEU names instead of "ceu".
This fixes "memchunk" kernel command line selection
on the solution engine 7724 board.
With this patch applied use "memchunk.ceu0=1m" or
"memchunk.ceu1=1m" on kernel command line to override
physically memory size to one meg for CEU0 or CEU1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (47 commits)
perf report: Add --symbols parameter
perf report: Add --comms parameter
perf report: Add --dsos parameter
perf_counter tools: Adjust only prelinked symbol's addresses
perf_counter: Provide a way to enable counters on exec
perf_counter tools: Reduce perf stat measurement overhead/skew
perf stat: Use percentages for scaling output
perf_counter, x86: Update x86_pmu after WARN()
perf stat: Micro-optimize the code: memcpy is only required if no event is selected and !null_run
perf stat: Improve output
perf stat: Fix multi-run stats
perf stat: Add -n/--null option to run without counters
perf_counter tools: Remove dead code
perf_counter: Complete counter swap
perf report: Print sorted callchains per histogram entries
perf_counter tools: Prepare a small callchain framework
perf record: Fix unhandled io return value
perf_counter tools: Add alias for 'l1d' and 'l1i'
perf-report: Add bare minimum PERF_EVENT_READ parsing
perf-report: Add modes for inherited stats and no-samples
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
Add Fenghua Yu as temporary co-maintainer for ia64
[IA64] address compiler warnings perfmon.c/salinfo.c
[IA64] Remove unnecessary semicolons
[IA64] sprintf should not be used with same source & destination address
Wire up new syscalls rt_tgsigqueueinfo and perf_counter_open.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wire up new syscalls rt_tgsigqueueinfo and perf_counter_open.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nathan reported that
| commit 73d60b7f74
| Author: Yinghai Lu <yinghai@kernel.org>
| Date: Tue Jun 16 15:33:00 2009 -0700
|
| page-allocator: clear N_HIGH_MEMORY map before we set it again
|
| SRAT tables may contains nodes of very small size. The arch code may
| decide to not activate such a node. However, currently the early boot
| code sets N_HIGH_MEMORY for such nodes. These nodes therefore seem to be
| active although these nodes have no present pages.
|
| For 64bit N_HIGH_MEMORY == N_NORMAL_MEMORY, so that works for 64 bit too
unintentionally and incorrectly clears the cpuset.mems cgroup attribute on
an i386 kvm guest, meaning that cpuset.mems can not be used.
Fix this by only clearing node_states[N_NORMAL_MEMORY] for 64bit only.
and need to do save/restore for that in find_zone_movable_pfn
Reported-by: Nathan Lynch <ntl@pobox.com>
Tested-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha percpu access requires custom SHIFT_PERCPU_PTR() definition for
modules to work around addressing range limitation. This is done via
generating inline assembly using C preprocessing which forces the
assembler to generate external reference. This happens behind the
compiler's back and makes the compiler think that static percpu variables
in modules are unused.
This used to be worked around by using __unused attribute for percpu
variables which prevent the compiler from omitting the variable; however,
recent declare/definition attribute unification change broke this as
__used can't be used for declaration. Also, in the process,
PER_CPU_ATTRIBUTES definition in alpha percpu.h got broken.
This patch adds PER_CPU_DEF_ATTRIBUTES which is only used for definitions
and make alpha use it to add __used for percpu variables in modules. This
also fixes the PER_CPU_ATTRIBUTES double definition bug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: maximilian attems <max@stro.at>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The merge of the 32- and 64-bit fixmap headers made a latent
bug on x86-64 a real one: with the right config settings
it is possible for FIX_OHCI1394_BASE to overlap the FIX_BTMAP_*
range.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <stable@kernel.org> # for 2.6.30.x
LKML-Reference: <4A4A0A8702000078000082E8@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Noticed the zero-sized function symbol while looking at 'perf' profiles,
it causes the profiler to display those addresses in hexa.
Turns out that this was wrong/bogus for an eternity.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Acked-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Cyrill Gorcunov <gorcunov@gmail.com>
LKML-Reference: <1246366820.6538.1.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
perfmon.c has a dubious cast directly from "int" to "void *". Add
an intermediate cast to "long" to keep gcc happy.
salinfo.c uses "down_trylock()" in a highly creative way (explained
in the comments in the file) ... but it does kick out this warning:
arch/ia64/kernel/salinfo.c:195: warning: ignoring return value of 'down_trylock'
which people occasionally try to "fix" in ways that do not work. Use some
casts to keep gcc quiet.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This happens to work at the moment but isn't a good idea so fix it the
simple way.
Resolves-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13576
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This allows us to remove adjust_transparent_bridge_resources and give
x86_pci_root_bus_res_quirks a chance when _CRS is not used or not there.
Acked-by: Gary Hade <garyhade@us.ibm.com>
Tested-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Don't touch info->res_num if we are out of space.
Acked-by: Gary Hade <garyhade@us.ibm.com>
Tested-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It seems that mn10300 made it upstream after Jan Beulich's pci_dac_dma_*
cleanup work and still defines pci_dac_dma_supported(). This API is not
required by the PCI subsystem anymore, so remove it.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "x86: cap iomem_resource to addressable physical memory"
There's no need for the GFX workaround now we have 'iommu=pt' for the
cases where people really care about performance. There's no need to
have a special case for just one type of device.
This also speeds up the iommu=pt path and reduces memory usage by
setting up the si_domain _once_ and then using it for all devices,
rather than giving each device its own private page tables.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds input keyboard gpio support on at91sam9g20ek board.
It adds button 3 and 4.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The print out should read the value before changing the value.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4A487017.4090007@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: shut up uninit compiler warning in paging_tmpl.h
KVM: Ignore reads to K7 EVNTSEL MSRs
KVM: VMX: Handle vmx instruction vmexits
KVM: s390: Allow stfle instruction in the guest
KVM: kvm/x86_emulate.c toggle_interruptibility() should be static
KVM: ia64: fix ia64 build due to missing kallsyms_lookup() and double export
KVM: protect concurrent make_all_cpus_request
KVM: MMU: Allow 4K ptes with bit 7 (PAT) set
KVM: Fix dirty bit tracking for slots with large pages
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, delay: tsc based udelay should have rdtsc_barrier
x86, setup: correct include file in <asm/boot.h>
x86, setup: Fix typo "CONFIG_x86_64" in <asm/boot.h>
x86, mce: percpu mcheck_timer should be pinned
x86: Add sysctl to allow panic on IOCK NMI error
x86: Fix uv bau sending buffer initialization
x86, mce: Fix mce resume on 32bit
x86: Move init_gbpages() to setup_arch()
x86: ensure percpu lpage doesn't consume too much vmalloc space
x86: implement percpu_alloc kernel parameter
x86: fix pageattr handling for lpage percpu allocator and re-enable it
x86: reorganize cpa_process_alias()
x86: prepare setup_pcpu_lpage() for pageattr fix
x86: rename remap percpu first chunk allocator to lpage
x86: fix duplicate free in setup_pcpu_remap() failure path
percpu: fix too lazy vunmap cache flushing
x86: Set cpu_llc_id on AMD CPUs
Dixes compilation warning:
CC arch/x86/kernel/io_delay.o
arch/x86/kvm/paging_tmpl.h: In function ‘paging64_fetch’:
arch/x86/kvm/paging_tmpl.h:279: warning: ‘sptep’ may be used uninitialized in this function
arch/x86/kvm/paging_tmpl.h: In function ‘paging32_fetch’:
arch/x86/kvm/paging_tmpl.h:279: warning: ‘sptep’ may be used uninitialized in this function
warning is bogus (always have a least one level), but need to shut the compiler
up.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In commit 7fe29e0faa we ignored the
reads to the P6 EVNTSEL MSRs. That fixed crashes on Intel machines.
Ignore the reads to K7 EVNTSEL MSRs as well to fix this on AMD
hosts.
This fixes Kaspersky antivirus crashing Windows guests on AMD hosts.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
IF a guest tries to use vmx instructions, inject a #UD to let it know the
instruction is not implemented, rather than crashing.
This prevents guest userspace from crashing the guest kernel.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
2.6.31-rc introduced an architecture level set checker based on facility
bits. e.g. if the kernel is compiled to run only on z9, several facility
bits are checked very early and the kernel refuses to boot if a z9 specific
facility is missing.
Until now kvm on s390 did not implement the store facility extended (STFLE)
instruction. A 2.6.31-rc kernel that was compiled for z9 or higher did not
boot in kvm. This patch implements stfle.
This patch should go in before 2.6.31.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
toggle_interruptibility() is used only by same file, it should be static.
Fixed following sparse warning :
arch/x86/kvm/x86_emulate.c:1364:6: warning: symbol 'toggle_interruptibility' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix problem with double export of certain symbols from vsprintf.c
which we do not wish to export from the kvm-intel.ko module.
In addition, we do not have access to kallsyms_lookup() from the
module, so make sure to #undef CONFIG_KALLSYMS
Signed-off-by: Jes Sorensen <jes@sgi.com>
Acked-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This reverts commit 95ee14e437.
Mikael Petterson <mikepe@it.uu.se> reported that at least one of his
systems will not boot as a result. We have ruled out the detection
algorithm malfunctioning, so it is not a matter of producing the
incorrect bitmasks; rather, something in the application of them
fails.
Revert the commit until we can root cause and correct this problem.
-stable team: this means the underlying commit should be rejected.
Reported-and-isolated-by: Mikael Petterson <mikpe@it.uu.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <200906261559.n5QFxJH8027336@pilspetsen.it.uu.se>
Cc: stable@kernel.org
Cc: Grant Grundler <grundler@parisc-linux.org>
Here is a little update to the at91sam9rlek lcd interface.
This will correct the power pin of the LCD.
It will also add precision to the struct atmel_lcdfb_info
scructure: backlight enabling and wiring mode correction:
RGB wiring on the -EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We recently added a INIT_TASK(align) in include/asm-generic/vmlinux.lds.h,
but there is already a macro INIT_TASK in include/linux/init_task.h, which
is quite confusing. We should switch the macro in the linker script to
INIT_TASK_DATA. (Sorry that I missed this in reviewing the patch). Since
the macros are new, there is only one user of the INIT_TASK in
vmlinux.lds.h, arch/mn10300/kernel/vmlinux.lds.S.
However, we are currently using INIT_TASK_DATA for laying down an entire
.data.init_task section. So rename that to INIT_TASK_DATA_SECTION.
I would be worried about changing the meaning of INIT_TASK_DATA, but the
old INIT_TASK_DATA implementation had no users, and in fact if anyone had
tried to use it, it would have failed to compile because it didn't pass
the alignment to the old INIT_TASK.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (29 commits)
powerpc/rtas: Fix watchdog driver temperature read functionality
powerpc/mm: Fix potential access to freed pages when using hugetlbfs
powerpc/440: Fix warning early debug code
powerpc/of: Fix usage of dev_set_name() in of_device_alloc()
powerpc/pasemi: Use raw spinlock in SMP TB sync
powerpc: Use one common impl. of RTAS timebase sync and use raw spinlock
powerpc/rtas: Turn rtas lock into a raw spinlock
powerpc: Add irqtrace support for 32-bit powerpc
powerpc/BSR: Fix BSR to allow mmap of small BSR on 64k kernel
powerpc/BSR: add 4096 byte BSR size
powerpc: Map more memory early on 601 processors
powerpc/pmac: Fix DMA ops for MacIO devices
powerpc/mm: Make k(un)map_atomic out of line
powerpc: Fix mpic alloc warning
powerpc: Fix output from show_regs
powerpc/pmac: Fix issues with PowerMac "PowerSurge" SMP
powerpc/amigaone: Limit ISA I/O range to 4k in the device tree
powerpc/warp: Platform fix for i2c change
powerpc: Have git ignore generated files from dtc compile
powerpc/mpic: Fix mapping of "DCR" based MPIC variants
...
When using 64k page sizes, our PTE pages are split in two halves,
the second half containing the "extension" used to keep track of
individual 4k pages when not using HW 64k pages.
However, our page tables used for hugetlb have a slightly different
format and don't carry that "second half".
Our code that batched PTEs to be invalidated unconditionally reads
the "second half" (to put it into the batch), which means that when
called to invalidate hugetlb PTEs, it will access unrelated memory.
It breaks when CONFIG_DEBUG_PAGEALLOC is enabled.
This fixes it by only accessing the second half when the _PAGE_COMBO
bit is set in the first half, which indicates that we are dealing with
a "combo" page which represents 16x4k subpages. Anything else shouldn't
have this bit set and thus not require loading from the second half.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The function udbg_44x_as1_flush() has the wrong prototype causing
a warning when enabling 440 early debug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
dev_set_name() takes a format string, so use it properly and avoid
a warning with recent gcc's
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
spin_lock() can hang if called while the timebase is frozen,
so use a raw lock instead, also disable interrupts while
at it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several platforms use their own copy of what is essentially the same code,
using RTAS to synchronize the timebases when bringing up new CPUs. This
moves it all into a single common implementation and additionally
turns the spinlock into a raw spinlock since the former can rely on
the timebase not being frozen when spinlock debugging is enabled, and finally
masks interrupts while the timebase is disabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
RTAS currently uses a normal spinlock. However it can be called from
contexts where this is not necessarily a good idea. For example, it
can be called while syncing timebases, with the core timebase being
frozen. Unfortunately, that will deadlock in case of lock contention
when spinlock debugging is enabled as the spin lock debugging code
will try to use __delay() which ... relies on the timebase being
enabled.
Also RTAS can be used in some low level IRQ handling code path so it
may as well be a raw spinlock for -rt sake.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on initial work from: Dale Farnsworth <dale@farnsworth.org>
Add the low level irq tracing hooks for 32-bit powerpc needed
to enable full lockdep functionality.
The approach taken to deal with the code in entry_32.S is that
we don't trace all the transitions of MSR:EE when we just turn
it off to peek at TI_FLAGS without races. Only when we are
calling into C code or returning from exceptions with a state
that have changed from what lockdep thinks.
There's a little bugger though: If we take an exception that
keeps interrupts enabled (such as an alignment exception) while
interrupts are enabled, we will call trace_hardirqs_on() on the
way back spurriously. Not a big deal, but to get rid of it would
require remembering in pt_regs that the exception was one of the
type that kept interrupts enabled which we don't know at this
stage. (Well, we could test all cases for regs->trap but that
sucks too much).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Kumar Gala <galak@kernel.crashing.org>
The 32-bit kernel relies on some memory being mapped covering
the kernel text,data and bss at least, early during boot before
the full MMU setup is done. On 32-bit "classic" processors, this
is done using BAT registers.
On 601, the size of BATs is limited to 8M and we use 2 of them
for that initial mapping. This can become quite tight when enabling
features like lockdep, so let's use a 3rd one to bump that mapping
from 16M to 24M. We keep the 4th BAT free as it can be useful for
debugging early boot code to map things like serial ports.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those functions are way too big to be inline, besides, kmap_atomic()
wants to call debug_kmap_atomic() which isn't exported for modules
and causes module link failures.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For some reason we've had an explicit KERN_INFO for GPR dumps. With
recent changes we get output like:
<6>GPR00: 00000000 ef855eb0 ef858000 00000001 000000d0 f1000000 ffbc8000 ffffffff
The KERN_INFO is causing the <6>. Don't see any reason to keep it
around.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The old PowerSurge SMP (ie, dual or quad 604 machines) code has
numerous issues in modern world.
One is cpu_possible_map is set too late (the device-tree is bogus)
so we fail to allocate the interrupt stacks and crash. Another
problem is the fact the timebase is frozen by the bringup of the
second CPU so the delays in the generic code will hang, we need
to move some of the calling procedure to inside the powermac code.
This makes it boot again for me
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel reserves the I/O address space from 0x0 to 0xfff for legacy
ISA devices. Change the ranges property for the PCI2ISA bridge to match
the kernels behavior, even if the ranges property isn't used for now.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A change to the i2c subsystem breaks the warp platform code. The patch
is cleaner anyway, the old way was a bit crufty.
For those with keen eyes, the gratuitous change in the string from
PIKA to Warp is just so the logs look a bit nicer. The following two
lines tend to be printed one after another.
Warp POST OK
Warp DTM thread running.
Yeah, this will be the third patch to warp.c submitted in this
release....
Cheers,
Sean
The i2c_client struct changed, breaking the code that looked for the ad7414
chip. Use the new of_find_i2c_device_by_node function added in 2.6.29.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Have git ignore generated files from dtc compile
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 31207dab7d
"Fix incorrect allocation of interrupt rev-map"
introduced a regression crashing on boot on machines using
a "DCR" based MPIC, such as the Cell blades.
The reason is that the irq host data structure is initialized
much later as a result of that patch, causing our calls to
mpic_map() do be done before we have a host setup.
Unfortunately, this breaks _mpic_map_dcr() which uses the
mpic->irqhost to get to the device node.
This fixes it by, instead, passing the device node explicitely
to mpic_map().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Turning on SWIOTLB selects or enables PPC_NEED_DMA_SYNC_OPS, which means
we get the non empty versions of dma_sync_* in asm/dma-mapping.h
On my pseries machine the dma_ops have no such routines and we die with
a null pointer - this patch gets it booting, is there a more elegant way
to do it?
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The tftpboot build was failing with missing file errors.
It turns out that $(obj)/image wasn't being generated which was causing the a.out conversion to be skipped and hence piggyback to be called with nonexistent files.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kjetil Oftedal mentioned that piggyback_32 was failing
when building a sparc image.
I tracked this down to the fact that the kernel no longer
provided an absolute symbol named "end".
Commit 86ed40bd6f ("sparc: unify sections.h")
renamed end to _end but failed to update piggyback_32.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Kjetil Oftedal <oftedal@gmail.com>
Cc: Robert Reif <reif@earthlink.net>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following build warnings:
arch/sparc/boot/piggyback_64.c: In function 'main':
arch/sparc/boot/piggyback_64.c:44: warning: 'end' may be used uninitialized in this function
arch/sparc/boot/piggyback_64.c:44: warning: 'start' may be used uninitialized in this function
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The page allocator and SLAB are available at this point now,
and if we still try to use bootmem allocations here the kernel
spits out warnings.
Signed-off-by: David S. Miller <davem@davemloft.net>
<asm/boot.h> needs <asm/pgtable_types.h>, not <asm/page_types.h> in
order to resolve PMD_SHIFT. Also, correct a +1 which really should be
+ THREAD_ORDER.
This is a build error which was masked by a typoed #ifdef.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
CONFIG_X86_64 was misspelled (wrong case), which caused the x86-64
kernel to advertise itself as more relocatable than it really is.
This could in theory cause boot failures once bootloaders start
support the new relocation fields.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
If CONFIG_NO_HZ + CONFIG_SMP, timer added via add_timer() might
be migrated on other cpu. Use add_timer_on() instead.
Avoids the following failure:
Maciej Rutecki wrote:
> > After normal boot I try:
> >
> > echo 1 > /sys/devices/system/machinecheck/machinecheck0/check_interval
> >
> > I found this in dmesg:
> >
> > [ 141.704025] ------------[ cut here ]------------
> > [ 141.704039] WARNING: at arch/x86/kernel/cpu/mcheck/mce.c:1102
> > mcheck_timer+0xf5/0x100()
Reported-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch introduces a new sysctl:
/proc/sys/kernel/panic_on_io_nmi
which defaults to 0 (off).
When enabled, the kernel panics when the kernel receives an NMI
caused by an IO error.
The IO error triggered NMI indicates a serious system
condition, which could result in IO data corruption. Rather
than contiuing, panicing and dumping might be a better choice,
so one can figure out what's causing the IO error.
This could be especially important to companies running IO
intensive applications where corruption must be avoided, e.g. a
bank's databases.
[ SuSE has been shipping it for a while, it was done at the
request of a large database vendor, for their users. ]
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: Roberto Angelino <robertangelino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <20090624213211.GA11291@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update the mmap control page with the needed information to
use the userspace RDPMC instruction for self monitoring.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UML: Fix some apparent bitrot
- migration of net_device methods into net_device_ops
- dma_sync_single() changes
Signed-off-by: Paul Menage <menage@google.com>
Acked-by: Amerigo Wang <xiyou.wangcong@gmail.com>
--
This version is split from my earlier patch, including just the
portions that ar required for Linus' tree.
Fixes the following compile errors:
include/linux/dma-mapping.h:113: error: redefinition of 'dma_sync_single'
arch/um/include/asm/dma-mapping.h:84: error: previous definition of 'dma_sync_single' was here
include/linux/dma-mapping.h: In function 'dma_sync_single':
include/linux/dma-mapping.h:117: error: implicit declaration of function 'dma_sync_single_for_cpu'
include/linux/dma-mapping.h: At top level:
include/linux/dma-mapping.h:120: error: redefinition of 'dma_sync_sg'
arch/um/include/asm/dma-mapping.h:91: error: previous definition of 'dma_sync_sg' was here
include/linux/dma-mapping.h: In function 'dma_sync_sg':
include/linux/dma-mapping.h:124: error: implicit declaration of function 'dma_sync_sg_for_cpu'
arch/um/drivers/slirp_kern.c: In function 'slirp_init':
arch/um/drivers/slirp_kern.c:35: error: 'struct net_device' has no member named 'init'
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the link script for ARM to use PAGE_SIZE instead of hard-
coded 4096. Also the old RODATA macro is deprecated
for the RO_DATA(PAGE_SIZE) macro. As a consequence the PAGE_SIZE
was changed from (1UL << PAGE_SHIFT) to (_AC(1,UL) << PAGE_SHIFT)
because the linker does not understand the "UL" suffix to numeric
constants.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
handle_bad_irq() expects the IRQ number to be valid (used for statistics),
so it cannot be called with an illegal vector. The problem was reported
by a static analysis tool.
The change makes bad_irq_desc redundant, so delete it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 9e9f46c44e.
Quoting from the commit message:
"At this point, it seems to solve more problems than it causes, so let's
try using it by default. It's an easy revert if it ends up causing
trouble."
And guess what? The _CRS code causes trouble.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Staging: octeon-ethernet: Fix race freeing transmit buffers.
Staging: octeon-ethernet: Convert to use net_device_ops.
MIPS: Cavium: Add CPU hotplugging code.
MIPS: SMP: Allow suspend and hibernation if CPU hotplug is available
MIPS: Add arch generic CPU hotplug
DMA: txx9dmac: use dma_unmap_single if DMA_COMPL_{SRC,DEST}_UNMAP_SINGLE set
MIPS: Sibyte: Fix build error if CONFIG_SERIAL_SB1250_DUART is undefined.
MIPS: MIPSsim: Fix build error if MSC01E_INT_BASE is undefined.
MIPS: Hibernation: Remove SMP TLB and cacheflushing code.
MIPS: Build fix - include <linux/smp.h> into all smp_processor_id() users.
MIPS: bug.h Build fix - include <linux/compiler.h>.
The SMP implementation of suspend and hibernate depends on CPU hotplugging.
In the past we didn't have CPU hotplug so suspend and hibernation were not
possible on SMP systems.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Each platform has to add support for CPU hotplugging itself by providing
suitable definitions for the cpu_disable and cpu_die of the smp_ops
methods and setting SYS_SUPPORTS_HOTPLUG_CPU. A platform should only set
SYS_SUPPORTS_HOTPLUG_CPU once all it's smp_ops definitions have the
necessary changes. This patch contains the changes to the dummy smp_ops
definition for uni-processor systems.
Parts of the code contributed by Cavium Inc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can't perform any flushes on SMP from swsusp_arch_resume because
interrupts are disabled. A cross-CPU flush is unnecessary anyway
because all but the local CPU have already been disabled. A local
flush is not needed either because we didn't change any mappings. So
just delete the code.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some of the were relying into smp.h being dragged in by another header
which of course is fragile. <asm/cpu-info.h> uses smp_processor_id()
only in macros and including smp.h there leads to an include loop, so
don't change cpu-info.h.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds page fault instrumentation for the software performance
counters. Follows the x86 and powerpc changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (72 commits)
asus-laptop: remove EXPERIMENTAL dependency
asus-laptop: use pr_fmt and pr_<level>
eeepc-laptop: cpufv updates
eeepc-laptop: sync eeepc-laptop with asus_acpi
asus_acpi: Deprecate in favor of asus-laptop
acpi4asus: update MAINTAINER and KConfig links
asus-laptop: platform dev as parent for led and backlight
eeepc-laptop: enable camera by default
ACPI: Rename ACPI processor device bus ID
acerhdf: Acer Aspire One fan control
ACPI: video: DMI workaround broken Acer 7720 BIOS enabling display brightness
ACPI: run ACPI device hot removal in kacpi_hotplug_wq
ACPI: Add the reference count to avoid unloading ACPI video bus twice
ACPI: DMI to disable Vista compatibility on some Sony laptops
ACPI: fix a deadlock in hotplug case
Show the physical device node of backlight class device.
ACPI: pdc init related memory leak with physical CPU hotplug
ACPI: pci_root: remove unused dev/fn information
ACPI: pci_root: simplify list traversals
ACPI: pci_root: use driver data rather than list lookup
...
The initialization of the UV Broadcast Assist Unit's sending
buffers was making an invalid assumption about the
initialization of an MMR that defines its address.
The BIOS will not be providing that MMR. So
uv_activation_descriptor_init() should unconditionally set it.
Tested on UV simulator.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org> # for v2.6.30.x
LKML-Reference: <E1MJTfj-0005i1-W8@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Previous code made an assumption that the power on value of global
control MSR has enabled all fixed and general purpose counters properly.
However, this is not the case for certain Intel processors, such as
Atom - and it might also be firmware dependent.
Each enable bit in IA32_PERF_GLOBAL_CTRL is AND'ed with the
enable bits for all privilege levels in the respective IA32_PERFEVTSELx
or IA32_PERF_FIXED_CTR_CTRL MSRs to start/stop the counting of
respective counters. Counting is enabled if the AND'ed results is true;
counting is disabled when the result is false.
The end result is that all fixed counters are always disabled on Atom
processors because the assumption is just invalid.
Fix this by not initializing the ctrl-mask out of the global MSR,
but setting it to perf_counter_mask.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090624021324.GA2788@ywang-moblin2.bj.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/iommu-2.6:
Intel-IOMMU, intr-remap: source-id checking
Intel-IOMMU, intr-remap: set the whole 128bits of irte when modify/free it
IOMMU Identity Mapping Support (drivers/pci/intel_iommu.c)
This patch fixes two errors we get when building GTA02 kernel.
~ use_bbt is incorrect, we need flash_bbt.
~ We do not need .force_soft_ecc because we can unset
CONFIG_MTD_NAND_S3C2410_HWECC.
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: updated patch description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
To support domain-isolation usages, the platform hardware must be
capable of uniquely identifying the requestor (source-id) for each
interrupt message. Without source-id checking for interrupt remapping
, a rouge guest/VM with assigned devices can launch interrupt attacks
to bring down anothe guest/VM or the VMM itself.
This patch adds source-id checking for interrupt remapping, and then
really isolates interrupts for guests/VMs with assigned devices.
Because PCI subsystem is not initialized yet when set up IOAPIC
entries, use read_pci_config_byte to access PCI config space directly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Calling mcheck_init() on resume is required only with
CONFIG_X86_OLD_MCE=y.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Fix the incorrect "select" directives by dropping the "CONFIG_"
prefixes, and correcting the typo "H8S2768" to "H8S2678".
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix up HAVE_PERF_COUNTERS typo.
sh: Fix up more dma-mapping fallout.
sh: SH7786 SMP support.
sh: Wire up the uncached fixmap on sh64 as well.
sh: Use local TLB flush in set_pte_phys().
sh: Provide cpu_idle_wait() to fix up cpuidle/SMP build.
The commit 9db41f9edc added
the .flash_bbt flag to the nand set, so add this back into
the mach-mini2440.c file (taken out on initial commit to
allow build).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
That's HAVE_PERF_COUNTERS not HAVE_PERF_COUNTER. This was right
initially but I seem to have screwed it up while re-typing it out
by hand on another machine when I checked it in. Hmph.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 52da219e96 added IIS
platform devices, but these do not build on s3c24xx systems
and the file depends on SND_S3C24XX_SOC, which is selected
for all S3C64XX/S3C24XX systems.
As a quick fix, make the dev-audio.o file depends on
SND_S3C64XX_SOC_I2S instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 52da219e96 removed
the s3c_device_iis, but didn't replace it with anything
so a number of s3c24xx machines are currently failing
to build.
As a temporary fix, re-instate s3c_device_iis until a
proper replacement can be done for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The commit ec976d6eb0
removed a number of gpio definitions from <mach/hardware.h>
but misssed updating these two files:
Fix the following build errors by including <linux/gpio.h>:
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c: In function 's3c24xx_spi_gpiocfg_bus1_gpg5_6_7':
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c: In function 's3c24xx_spi_gpiocfg_bus0_gpe11_12_13':
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For yet unknown reason 4-bit mode doesn't work on MPC8569E-MDS boards,
so make 1-bit mode default. When we resolve the issue, u-boot will
remove sdhci,1-bit-only property from the device tree, while SDHCI
will still work with older u-boots.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL RapidIO won't probe without a proper compatible entry. This
patch fixes the issue by adding fsl,rapidio-delta compatible to
mpc85xx_ids.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Match what other 85xx platforms do for of_platform_bus_probe and use
machine_device_initcall. This is one small step in killing of
ppc_md.init.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The qe_issue_cmd() function (Freescale PowerPC QUICC Engine library) polls
on a register until a status bit changes, but does not include a timeout
to handle the situation if the bit never changes. Change the code to use
the new spin_event_timeout() macro, which simplifies polling on a register
without a timeout.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The "EET" variant of the pcm037 board has an OLED display, using a S6E63D6
display controller on the first SPI interface, using GPIO57 as a chip-select
for it. S6E63D6 is initialised in the boot-loader, so we only have to take care
of the LCD. EET also adds several buttons and LEDs on GPIOs. This patch adds a
"pcm037_variant=" kernel command line parameter to specify at boot-time which
board the kernel is running on, default is "pcm970", specify "eet" for the EET
board.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for the MT9T031 CMOS camera sensor from Aptina to the PCM037
board. Also add two I2C iomux pin definitions, needed for pcm037. Also
remove now unneeded #ifdef CONFIG_I2C_IMX.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since recent mxc_nand driver fixes from linux-mtd this patch
add support for ST NAND02GW3B2CN6 (2k pages flash) placed on the armadillo 500
motherboard.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch add support for NOR flash mapping through the physmap driver.
The purpose is to maintain the original Atmark partition model.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove the unused CONFIG_DEBUG_S3C_PORT as we currently only have
support for using the S3C UARTs via the low-level debug code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CONFIG_S3C24XX_PWM was defined in arch/arm/plat-s3c24xx/Kconfig but
not used anywhere else as the corresponding makefile used
CONFIG_HAVE_PWM (selected by CONFIG_S3C24XX_PWM) to compile the PWM
driver.
Change the makefile to use CONFIG_S3C24XX_PWM to compile this driver
to ensure it is only build when needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some bootloader may initialize debounce register and this will make
dbclk not consist with the debounce register after linux kernel boot
up.
Signed-off-by: janboe <janboe.ye@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function flush_iotlb_page is not loading the CAM register with
the correct entry to be flushed, so it is flushing other entry
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use async timings when sync timings are not requested.
Also ensure that OneNAND is in async mode when async
timings are used.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables MStandby smart-idle mode, autoidle smartidle mode,
and the autoidle bit for DMA4_OCP_SYSCONFIG.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
SRAM size fix for HS/EMU devices
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap_type() function is added and returns the DEVICETYPE field of
the CONTROL_STATUS register. The result can be used for conditional
code based on whether device is GP (general purpose), EMU or
HS (high security). Also move the type defines so omap1 code
compile does not require ifdefs for sections using these defines.
This code is needed for the following fix to set the SRAM
size correctly for HS omaps. Also at least PM and watchdog
code will need this function.
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
platform_get_irq may return -ENXIO. but struct omap_mbox mbox_dsp_info.irq
is unsigned, so the error was not noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc23_set_power() has MMC2 twl_mmc_controller hardcoded in it, which
breaks MMC3. Find the right controller to use instead.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some of the N770's MMC configuration options seem to have been
dropped. This patch adds them back in again.
Note that only the .ocr_mask change was /critical/, but I've added the
.max_freq setting back as well, as the original sources had it. Can
anyone confirm if this is unnecessary?
Secondly, there is support in the original code for a 4wire/higher
speed mode. As I don't have the requisite N770 hardware (I think it
was a rev2 N770?) to test this, I can't really add it back.
Signed-off-by: Andrew de Quincey <adq@lidskialf.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes the positioning of " in MODULE_AUTHOR, which is currently
causing a build failure on latest git with CONFIG_OMAP_MBOX_FWK=m; the
original breakage appears to date from the end of last year in
a5abbbe52b
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit dbe6f18691
("dma-mapping: mark dma_sync_single and dma_sync_sg as deprecated"
conveniently broke every single SH build.
In the future it would be great if people could at least bother
figuring out how to use grep.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The init_gbpages() function is conditionally called from
init_memory_mapping() function. There are two call-sites where
this 'after_bootmem' condition can be true: setup_arch() and
mem_init() via pci_iommu_alloc().
Therefore, it's safe to move the call to init_gbpages() to
setup_arch() as it's always called before mem_init().
This removes an after_bootmem use - paving the way to remove
all uses of that state variable.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <Pine.LNX.4.64.0906221731210.19474@melkki.cs.Helsinki.FI>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SH7786 is roughly identical to SH-X3 proto SMP, though there are only 2
CPUs. This just wraps in to the existing SH-X3 SMP code with some minor
changes for SH7786, including wiring up the IPIs properly, enabling
IRQ_PER_CPU, and so forth.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
set_pte_phys() presently uses the global flush_tlb_one(), which locks on
SMP trying to do the IPI. As we have not even initialized the other CPUs
at this point, switch to the local_ variant so the flush happens on the
boot CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Crib the x86 cpu_idle_wait() implementation and shove it in with the
idle code, subsequently enabling ARCH_HAS_CPU_IDLE_WAIT.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since dmanr is unsigned, negatives are wrapped and caught by the other test.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (27 commits)
Blackfin: fix dma-mapping build errors
Blackfin: hook up new perf_counter_open syscall
Blackfin: drop BF535-specific text for exception 0x2A (unaligned instruction)
Blackfin: fix early crash when booting on wrong cpu
Blackfin: fix GPTMR0_CLOCKSOURCE dependency on BFIN_GPTIMERS
Blackfin: drop unused ISP1760 port1_disable from board resources
Blackfin: bf526-ezbrd: handle different SDRAM chips
Blackfin: fix typo in TRAS define in mem_init.h header
Blackfin: unify memory map headers
Blackfin: stick the CPU name into boot image name
Blackfin: update defconfigs
Blackfin: decouple unrelated cache settings to get exact behavior
Blackfin: update I-pipe patch level
Blackfin: remove obsolete mcount support from I-pipe code
Blackfin: allow CONFIG_TICKSOURCE_GPTMR0 with interrupt pipeline
Blackfin: convert interrupt pipeline to irqflags
Blackfin: allow people to select BF51x-0.1 silicon rev
Blackfin: bf526-ezbrd: set SPI flash resources to SST device
Blackfin: fix accidental reset in some boot modes
Blackfin: abstract irq14 lowering in do_irq
...
* git://git.infradead.org/~dwmw2/iommu-2.6.31:
intel-iommu: Fix one last ia64 build problem in Pass Through Support
VT-d: support the device IOTLB
VT-d: cleanup iommu_flush_iotlb_psi and flush_unmaps
VT-d: add device IOTLB invalidation support
VT-d: parse ATSR in DMA Remapping Reporting Structure
PCI: handle Virtual Function ATS enabling
PCI: support the ATS capability
intel-iommu: dmar_set_interrupt return error value
intel-iommu: Tidy up iommu->gcmd handling
intel-iommu: Fix tiny theoretical race in write-buffer flush.
intel-iommu: Clean up handling of "caching mode" vs. IOTLB flushing.
intel-iommu: Clean up handling of "caching mode" vs. context flushing.
VT-d: fix invalid domain id for KVM context flush
Fix !CONFIG_DMAR build failure introduced by Intel IOMMU Pass Through Support
Intel IOMMU Pass Through Support
Fix up trivial conflicts in drivers/pci/{intel-iommu.c,intr_remapping.c}
The recent deprecation of dma_sync_{sg,single} ironically broke Blackfin
systems. This is because we don't define dma_sync_sg_for_cpu at all, so
until the DMA asm-generic conversion/cleanup is done after the next
release, simply stub out the dma_sync_sg_for_{cpu,device} functions.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't support the BF535 at all, and the exception 0x2A text specific to
it is pretty verbose and confusing (since the behavior is simply odd), so
punt it to keep the noise down.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we process the kernel command line before poking the hardware,
so that we can process early printk. This helps ensure that if you boot
a kernel configured for a different processor, something will be left in
the log buffer.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The GPTMR0_CLOCKSOURCE Kconfig option requires the gptimers framework, so
make sure it is selected when this option is enabled.
Reported-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF526-EZBRD changed SDRAM chips between board revisions, so create a
timing table that can accommodate both.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We defined SDRAM_tRAS to TRAS_4, but then wrongly defined SDRAM_tRAS_num
to 3.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many aspects of the Blackfin memory map is exactly the same across all
variants. Rather than copy and paste all of these duplicated values in
each header, unify all of these into the common Blackfin memory map header
file. In the process, push down BF561 SMP specific stuff to the BF561
specific header to keep the noise down.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than use "Linux" in the boot image name (as this is redundant --
the image type is already set to "linux"), use the CPU name. This makes
it fairly obvious when a wrong image is accidentally booted. Otherwise
there is no kernel output and you waste time scratching your head
wondering wtf just happened.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current cache options don't really represent the hardware features.
They end up setting different aspects of the hardware so that the end
result is to turn on/off the cache. Unfortunately, when we hit cache
problems with the hardware, it's difficult to test different settings to
root cause the problem. The current settings also don't cleanly allow for
different caching behaviors with different regions of memory.
So split the configure options such that they properly reflect the settings
that are applied to the hardware.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF526-EZBRD has a SST SPI flash on it, not a ST Micro.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We read the SWRST (Software Reset) register to get at the last reset
state, and then we may configure the DOUBLE_FAULT bit to control behavior
when a double fault occurs. But if the lower bits of the register is
already set (like UART boot mode on a BF54x), we inadvertently make the
system reset by writing to the SYSTEM_RESET field at the same time. So
make sure the lower 4 bits are always cleared.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Split out the optional IRQ14 lowering code to further simplify the
asm_do_IRQ() function and keep the ifdef nest under control.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Take a page from x86 and abstract the stack checking out of the
asm_do_IRQ() function so that the result is easier to digest.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
With the common IRQ code initializing much more of the irq_desc state, we
can't blindly initialize it ourselves to the local bad_irq state. If we
do, we end up wrongly clobbering many fields. So punt most of the bad irq
code as the common layers will handle the default state, and simply call
handle_bad_irq() directly when the IRQ we are processing is invalid.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF533-EZKIT has two Flash In-System Programming devices hooked up to
the async memory bus, so add resources for the primary flashes and the
SRAMs on the devices.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The kgdb (in multiple places) and traps code developed pretty much
identical checks for how to access different regions of the Blackfin
memory map, but each wasn't 100%, so unify them to avoid duplication,
bitrot, and bugs with edge cases.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (49 commits)
[ARM] idle: clean up pm_idle calling, obey hlt_counter
[ARM] S3C: Fix gpio-config off-by-one bug
[ARM] S3C64XX: add to_irq() support for EINT() GPIO
[ARM] S3C64XX: clock.c: fix typo in usb-host clock ctrlbit
[ARM] S3C64XX: fix HCLK gate defines
[ARM] Update mach-types
[ARM] wire up rt_tgsigqueueinfo and perf_counter_open
OMAP2 clock/powerdomain: off by 1 error in loop timeout comparisons
OMAP3 SDRC: set FIXEDDELAY when disabling SDRC DLL
OMAP3: Add support for DPLL3 divisor values higher than 2
OMAP3 SRAM: convert SRAM code to use macros rather than magic numbers
OMAP3 SRAM: add more comments on the SRAM code
OMAP3 clock/SDRC: program SDRC_MR register during SDRC clock change
OMAP3 clock: add a short delay when lowering CORE clk rate
OMAP3 clock: initialize SDRC timings at kernel start
OMAP3 clock: remove wait for DPLL3 M2 clock to stabilize
[ARM] Add old Feroceon support to compressed/head.S
[ARM] 5559/1: Limit the stack unwinding caused by a kthread exit
[ARM] 5558/1: Add extra checks to ARM unwinder to avoid tracing corrupt stacks
[ARM] 5557/1: Discard some ARM.ex*.*exit.text sections when !HOTPLUG or !HOTPLUG_CPU
...
pm_idle is used by infrastructure (eg, cpuidle) which expects architectures
to call it in a certain way. Arrange for ARM to follow x86's lead on this
and call pm_idle() with interrupts already disabled. However, we expect
pm_idle() to enable interrupts before it returns.
Also, OMAP wants to be able to disable hlt-ing, so allow hlt_counter to
prevent all calls to pm_idle.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the MN10300 vmlinux ldscript. It needs to use various macros from
asm-generic/vmlinux.lds.h to correctly include all that it needs to.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
Fix gpio-config off-by-one bug. Without this patch, touching GPA0 pin on
S3C64XX platform causes kernel oops.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
N group
Add to_irq() function to onvert gpio to irq for external interrupt
group (GPN).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The usb-host clock was using the wrong define (the SCLK enable for the
usb-host-bus) to change the HCLK register instead of the HCLK_UHOST bit.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A few typos seems to have sneaked into the HCLK gate defines, causing the
usb host clock to not get enabled. Fix them according to the reference
manual and throw in the 3d accel bit for good measure.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
get_krobe_ctlblk returns a per cpu kprobe control block which holds
the state of the current cpu wrt to kprobe.
When inserting/removing a kprobe the state of the cpu which replaces
the code is changed to KPROBE_SWAP_INST. This however is done when
preemption is still enabled. So the state of the current cpu doesn't
necessarily reflect the real state.
To fix this move the code that changes the state to non-preemptible
context.
Reported-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace the spinlock used in the idle time accounting with a sequence
counter mechanism analog to seqlock.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix build error for !SMP:
arch/s390/power/built-in.o: In function `swsusp_arch_resume':
(.text+0x1b4): undefined reference to `smp_get_phys_cpu_id'
arch/s390/power/built-in.o: In function `swsusp_arch_resume':
(.text+0x288): undefined reference to `smp_switch_boot_cpu_in_resume'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove unneeded sanity checks from do_QDIO since this is the hot path.
Change the type of bufnr and count to unsigned int so the check for the
maximum value works.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The kernel now has kmemleak and kmemtrace so there's no reason to keep
this ugly s390 hack around. I am not sure how it's supposed to work on
SMP anyway as it uses a global variable to temporarily store the return
value of all kmalloc() calls:
void *b;
#define kmalloc(x...) (PRINT_INFO(" kmalloc %p\n",b=kmalloc(x)),b)
Cc: <linux-s390@vger.kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The slab allocator is earlier available so convert the
bootmem allocations to slab/gfp allocations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Daniel Glockner <dg@emlix.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Weiner <jw@emlix.com>
Cc: Oskar Schirmer <os@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Platform-specific configuration for the s6gmac driver, including the
PHY interrupt line.
Signed-off-by: Daniel Glockner <dg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Weiner <jw@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Implement an irq chip to handle interrupts via gpio. The GPIO chip
initialization function now takes a bitmask denoting pins that should
be configured for their alternate function.
changes compared to v1:
- fixed bug on edge interrupt configuration
- accommodated to function name change
- moved definition of VARIANT_NR_IRQS to this patch
- renamed __XTENSA_S6000_IRQ_H to _XTENSA_S6000_IRQ_H as requested
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
There are four slightly different dma engines on the s6000 family.
One for memory-memory transfers, the other three for memory-device.
This patch implements a platform-specific kernel-API to control these
engines. It is needed for the network, video, audio peripherals on
s6000.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glockner <dg@emlix.com>
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glockner <dg@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
There was already a PLATFORM_NR_IRQS define, which is now accompanied
by a VARIANT_NR_IRQS. To be able to initialize these interrupts,
init_IRQ now calls a variant specific hook.
Changes compared to v1:
- adapted to new CONFIG_VARIANT_IRQ_EXT
- removed definition and call of platform_init_IRQ as there already
is a platform_init_irq defined in asm/platform.h with a weak default
in kernel/platform.c
- renamed variant_init_IRQ to variant_init_irq
Note that I could not find the call site of platform_init_irq although
it is stated in platform.h that it is called from init_IRQ.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
The existing xtensa cache handling functions work on page-aligned
memory regions.
These functions are needed for the s6000 dma engine which can work on
a byte-granularity.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Cc: Johannes Weiner <jw@emlix.com>
Cc: Daniel Glockner <dg@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
On extreme configuration (e.g. 32bit 32-way NUMA machine), lpage
percpu first chunk allocator can consume too much of vmalloc space.
Make it fall back to 4k allocator if the consumption goes over 20%.
[ Impact: add sanity check for lpage percpu first chunk allocator ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
According to Andi, it isn't clear whether lpage allocator is worth the
trouble as there are many processors where PMD TLB is far scarcer than
PTE TLB. The advantage or disadvantage probably depends on the actual
size of percpu area and specific processor. As performance
degradation due to TLB pressure tends to be highly workload specific
and subtle, it is difficult to decide which way to go without more
data.
This patch implements percpu_alloc kernel parameter to allow selecting
which first chunk allocator to use to ease debugging and testing.
While at it, make sure all the failure paths report why something
failed to help determining why certain allocator isn't working. Also,
kill the "Great future plan" comment which had already been realized
quite some time ago.
[ Impact: allow explicit percpu first chunk allocator selection ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
lpage allocator aliases a PMD page for each cpu and returns whatever
is unused to the page allocator. When the pageattr of the recycled
pages are changed, this makes the two aliases point to the overlapping
regions with different attributes which isn't allowed and known to
cause subtle data corruption in certain cases.
This can be handled in simliar manner to the x86_64 highmap alias.
pageattr code should detect if the target pages have PMD alias and
split the PMD alias and synchronize the attributes.
pcpur allocator is updated to keep the allocated PMD pages map sorted
in ascending address order and provide pcpu_lpage_remapped() function
which binary searches the array to determine whether the given address
is aliased and if so to which address. pageattr is updated to use
pcpu_lpage_remapped() to detect the PMD alias and split it up as
necessary from cpa_process_alias().
Jan Beulich spotted the original problem and incorrect usage of vaddr
instead of laddr for lookup.
With this, lpage percpu allocator should work correctly. Re-enable
it.
[ Impact: fix subtle lpage pageattr bug and re-enable lpage ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Reorganize cpa_process_alias() so that new alias condition can be
added easily.
Jan Beulich spotted problem in the original cleanup thread which
incorrectly assumed the two existing conditions were mutially
exclusive.
[ Impact: code reorganization ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Make the following changes in preparation of coming pageattr updates.
* Define and use array of struct pcpul_ent instead of array of
pointers. The only difference is ->cpu field which is set but
unused yet.
* Rename variables according to the above change.
* Rename local variable vm to pcpul_vm and move it out of the
function.
[ Impact: no functional difference ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
The "remap" allocator remaps large pages to build the first chunk;
however, the name isn't very good because 4k allocator remaps too and
the whole point of the remap allocator is using large page mapping.
The allocator will be generalized and exported outside of x86, rename
it to lpage before that happens.
percpu_alloc kernel parameter is updated to accept both "remap" and
"lpage" for lpage allocator.
[ Impact: code cleanup, kernel parameter argument updated ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
In the failure path, setup_pcpu_remap() tries to free the area which
has already been freed to make holes in the large page. Fix it.
[ Impact: fix duplicate free in failure path ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aes-ni - Remove CRYPTO_TFM_REQ_MAY_SLEEP from fpu template
crypto: aes-ni - Do not sleep when using the FPU
crypto: aes-ni - Fix cbc mode IV saving
crypto: padlock-aes - work around Nano CPU errata in CBC mode
crypto: padlock-aes - work around Nano CPU errata in ECB mode
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This counts when building sched domains in case NUMA information
is not available.
( See cpu_coregroup_mask() which uses llc_shared_map which in turn is
created based on cpu_llc_id. )
Currently Linux builds domains as follows:
(example from a dual socket quad-core system)
CPU0 attaching sched-domain:
domain 0: span 0-7 level CPU
groups: 0 1 2 3 4 5 6 7
...
CPU7 attaching sched-domain:
domain 0: span 0-7 level CPU
groups: 7 0 1 2 3 4 5 6
Ever since that is borked for multi-core AMD CPU systems.
This patch fixes that and now we get a proper:
CPU0 attaching sched-domain:
domain 0: span 0-3 level MC
groups: 0 1 2 3
domain 1: span 0-7 level CPU
groups: 0-3 4-7
...
CPU7 attaching sched-domain:
domain 0: span 4-7 level MC
groups: 7 4 5 6
domain 1: span 0-7 level CPU
groups: 4-7 0-3
This allows scheduler to assign tasks to cores on different sockets
(i.e. that don't share last level cache) for performance reasons.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20090619085909.GJ5218@alberich.amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The discussion about using "access_ok()" in get_user_pages_fast() (see
commit 7f8189068726492950bf1a2dcfd9b51314560abf: "x86: don't use
'access_ok()' as a range check in get_user_pages_fast()" for details and
end result), made us notice that x86-64 was really being very sloppy
about virtual address checking.
So be way more careful and straightforward about masking x86-64 virtual
addresses:
- All the VIRTUAL_MASK* variants now cover half of the address
space, it's not like we can use the full mask on a signed
integer, and the larger mask just invites mistakes when
applying it to either half of the 48-bit address space.
- /proc/kcore's kc_offset_to_vaddr() becomes a lot more
obvious when it transforms a file offset into a
(kernel-half) virtual address.
- Unify/simplify the 32-bit and 64-bit USER_DS definition to
be based on TASK_SIZE_MAX.
This cleanup and more careful/obvious user virtual address checking also
uncovered a buglet in the x86-64 implementation of strnlen_user(): it
would do an "access_ok()" check on the whole potential area, even if the
string itself was much shorter, and thus return an error even for valid
strings. Our sloppy checking had hidden this.
So this fixes 'strnlen_user()' to do this properly, the same way we
already handled user strings in 'strncpy_from_user()'. Namely by just
checking the first byte, and then relying on fault handling for the
rest. That always works, since we impose a guard page that cannot be
mapped at the end of the user space address space (and even if we
didn't, we'd have the address space hole).
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (49 commits)
perfcounter: Handle some IO return values
perf_counter: Push perf_sample_data through the swcounter code
perf_counter tools: Define and use our own u64, s64 etc. definitions
perf_counter: Close race in perf_lock_task_context()
perf_counter, x86: Improve interactions with fast-gup
perf_counter: Simplify and fix task migration counting
perf_counter tools: Add a data file header
perf_counter: Update userspace callchain sampling uses
perf_counter: Make callchain samples extensible
perf report: Filter to parent set by default
perf_counter tools: Handle lost events
perf_counter: Add event overlow handling
fs: Provide empty .set_page_dirty() aop for anon inodes
perf_counter: tools: Makefile tweaks for 64-bit powerpc
perf_counter: powerpc: Add processor back-end for MPC7450 family
perf_counter: powerpc: Make powerpc perf_counter code safe for 32-bit kernels
perf_counter: powerpc: Change how processor-specific back-ends get selected
perf_counter: powerpc: Use unsigned long for register and constraint values
perf_counter: powerpc: Enable use of software counters on 32-bit powerpc
perf_counter tools: Add and use isprint()
...
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix out of scope variable access in sched_slice()
sched: Hide runqueues from direct refer at source code level
sched: Remove unneeded __ref tag
sched, x86: Fix cpufreq + sched_clock() TSC scaling
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (24 commits)
tracing/urgent: warn in case of ftrace_start_up inbalance
tracing/urgent: fix unbalanced ftrace_start_up
function-graph: add stack frame test
function-graph: disable when both x86_32 and optimize for size are configured
ring-buffer: have benchmark test print to trace buffer
ring-buffer: do not grab locks in nmi
ring-buffer: add locks around rb_per_cpu_empty
ring-buffer: check for less than two in size allocation
ring-buffer: remove useless compile check for buffer_page size
ring-buffer: remove useless warn on check
ring-buffer: use BUF_PAGE_HDR_SIZE in calculating index
tracing: update sample event documentation
tracing/filters: fix race between filter setting and module unload
tracing/filters: free filter_string in destroy_preds()
ring-buffer: use commit counters for commit pointer accounting
ring-buffer: remove unused variable
ring-buffer: have benchmark test handle discarded events
ring-buffer: prevent adding write in discarded area
tracing/filters: strloc should be unsigned short
tracing/filters: operand can be negative
...
Fix up kmemcheck-induced conflict in kernel/trace/ring_buffer.c manually
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (45 commits)
x86, mce: fix error path in mce_create_device()
x86: use zalloc_cpumask_var for mce_dev_initialized
x86: fix duplicated sysfs attribute
x86: de-assembler-ize asm/desc.h
i386: fix/simplify espfix stack switching, move it into assembly
i386: fix return to 16-bit stack from NMI handler
x86, ioapic: Don't call disconnect_bsp_APIC if no APIC present
x86: Remove duplicated #include's
x86: msr.h linux/types.h is only required for __KERNEL__
x86: nmi: Add Intel processor 0x6f4 to NMI perfctr1 workaround
x86, mce: mce_intel.c needs <asm/apic.h>
x86: apic/io_apic.c: dmar_msi_type should be static
x86, io_apic.c: Work around compiler warning
x86: mce: Don't touch THERMAL_APIC_VECTOR if no active APIC present
x86: mce: Handle banks == 0 case in K7 quirk
x86, boot: use .code16gcc instead of .code16
x86: correct the conversion of EFI memory types
x86: cap iomem_resource to addressable physical memory
x86, mce: rename _64.c files which are no longer 64-bit-specific
x86, mce: mce.h cleanup
...
Manually fix up trivial conflict in arch/x86/mm/fault.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
It's really not right to use 'access_ok()', since that is meant for the
normal "get_user()" and "copy_from/to_user()" accesses, which are done
through the TLB, rather than through the page tables.
Why? access_ok() does both too few, and too many checks. Too many,
because it is meant for regular kernel accesses that will not honor the
'user' bit in the page tables, and because it honors the USER_DS vs
KERNEL_DS distinction that we shouldn't care about in GUP. And too few,
because it doesn't do the 'canonical' check on the address on x86-64,
since the TLB will do that for us.
So instead of using a function that isn't meant for this, and does
something else and much more complicated, just do the real rules: we
don't want the range to overflow, and on x86-64, we want it to be a
canonical low address (on 32-bit, all addresses are canonical).
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b99b87f70c add CONSTRUCTOR
support to Linux but Microblaze not defined KERNEL_CTORS symbols
which are used with that patch.
This patch fixed it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Alexey removed the definition for init_mm from all architectures
but forgot microblaze, which was only recently added.
This fixes the microblaze build by dropping it there as well.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <monstr@monstr.eu>
arch_acpi_processor_cleanup_pdc() in x86 and ia64 results in memory allocated
for _PDC objects that is never freed and will cause memory leak in case of
physical CPU remove and add. Patch fixes the memory leak by freeing the
objects soon after _PDC is evaluated.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
with while (i++ < MAX_CLOCK_ENABLE_WAIT); i can reach MAX_CLOCK_ENABLE_WAIT + 1
after the loop, so if (i == MAX_CLOCK_ENABLE_WAIT) that's still success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Correspondence with the TI OMAP hardware team indicates that
SDRC_DLLA_CTRL.FIXEDDELAY should be initialized to 0x0f. This number
was apparently derived from process validation. This is only used
when the SDRC DLL is unlocked (e.g., SDRC clock frequency less than
83MHz).
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Program the SDRC_MR_0 register as well during SDRC clock changes.
This register allows selection of the memory CAS latency. Some SDRAM
chips, such as the Qimonda HYB18M512160AF6, have a lower CAS latency
at lower clock rates.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When changing the SDRAM clock from 166MHz to 83MHz via the CORE DPLL M2
divider, add a short delay before returning to SDRAM to allow the SDRC
time to stabilize. Without this delay, the system is prone to random
panics upon re-entering SDRAM.
This time delay varies based on MPU frequency. At 500MHz MPU frequency at
room temperature, 64 loops seems to work okay; so add another 32 loops for
environmental and process variation.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On the OMAP3, initialize SDRC timings when the kernel boots. This ensures
that the kernel is running with known, optimized SDRC timings, rather than
whatever was configured by the bootloader.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The original CDP kernel that this code comes from waited for 0x800
loops after switching the CORE DPLL M2 divider. This does not appear
to be necessary.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: convert page/tlb to asm-generic
Blackfin: convert types to asm-generic
Blackfin: convert irq/process to asm-generic
Blackfin: convert signal/mmap to asm-generic
Blackfin: convert locking primitives to asm-generic
Blackfin: convert termios to asm-generic
Blackfin: convert simple headers to asm-generic
Blackfin: convert socket/poll to asm-generic
Blackfin: convert user/elf to asm-generic
Blackfin: convert shm/sysv/ipc to asm-generic
Blackfin: convert asm/ioctls.h to asm-generic/ioctls.h
Blackfin: only build irqpanic.c when needed
Blackfin: pull in asm/io.h in ksyms for prototypes
Blackfin: use common test_bit() rather than __test_bit()
This patch adds spi and mmc-spi-slot nodes, plus a gpio-controller for
PIXIS' sdcsr bank that is used for managing SPI chip-select and for
reading card's states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch supports the cache handling for some old Feroceon cores for
which the CPU ID is like 0x41159260. This is a complement to
commit ab6d15d506.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
When a kthread function returns, it branches to do_exit(). However, the
unwinding information isn't valid anymore and any stack trace caused by
do_exit() may be incorrect. This patch adds a kernel_thread_exit()
function and annotated with '.cantunwind' so that the unwinder stops
when reaching it.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are situations where the unwinder goes beyond stack boundaries and
unwinds random data. This patch moves the stack boundaries check after
the unwind_exec_insn() call and adds an extra check for possible
infinite loops (like "mov pc, lr" with pc == lr).
The patch also fixes a bug in the unwind instructions interpreter. The
0xb0 instruction can only set PC to LR if this wasn't already set by
a previous instruction (this is used on exceptions taken while in kernel
mode where svc_entry is annotated with ".save {r0 - pc}").
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Not discarding these sections when hotplug isn't available prevents the
kernel from building.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Min Zhang <mzhang@mvista.com>
Add alignment fault fixup support for 32-bit Thumb-2 LDM, LDRD, POP,
PUSH, STM and STRD instructions. Alignment fault fixup support for
the remaining 32-bit Thumb-2 load/store instruction cases is not
included since ARMv6 and later processors include hardware support
for loads and stores of unaligned words and halfwords.
Signed-off-by: Min Zhang <mzhang@mvista.com>
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Improve a few details in perfcounter call-chain recording that
makes use of fast-GUP:
- Use ACCESS_ONCE() to observe the pte value. ptes are fundamentally
racy and can be changed on another CPU, so we have to be careful
about how we access them. The PAE branch is already careful with
read-barriers - but the non-PAE and 64-bit side needs an
ACCESS_ONCE() to make sure the pte value is observed only once.
- make the checks a bit stricter so that we can feed it any kind of
cra^H^H^H user-space input ;-)
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The cpu member of struct irq_desc was recently renamed to node. The
patch renames the ARM references to the old member.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This header file is needed for twd_base.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Before exposing upstream tools to a callchain-samples ABI, tidy it
up to make it more extensible in the future:
Use markers in the IP chain to denote context, use (u64)-1..-4095 range
for these context markers because we use them for ERR_PTR(), so these
addresses are unlikely to be mapped.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit b696fdc259 ("sparc64: Defer
cpu_data() setup until end of per-cpu data initialization.") broke
bootup for UP builds because the cpu_data() initialization only
occurs in setup_per_cpu_areas() which is never compiled in nor
called in UP builds.
Fix this up by calling the setups directly from init_64.c when
non-SMP.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaswinder Singh Rajput