All callsites of x1205_set_datetime() want the date to be set as well, so
remove the flag parameter and set it unconditionally.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's possible to have RTC irq shared with other device (e.g.
mpc8349e-mitx board shares ds1339 irq with phy one). Handle this in
driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This switches __raw_[read|write]l() for plain [read|write]l in the PL031
RTC driver. The sister driver for PL030 use the simple accessors as most
PrimeCell drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds basic support for Texas Instruments BQ32000 I2C RTC. Only
time reading/writing is implemented. Advanced features, such as trickle
charger and crystal calibration are not supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-omap driver currently assumes that the rtc's registers are at a
fixed address and already mapped into virtual memory space. Remove those
assumptions so the same driver can be used for similar devices that reside
at different physical addresses (e.g., TI's DA8xx/OMAP-L13x SoC's).
Also allow the possibility for the timer and alarm interrupts to use the
same IRQ.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver provides support for the RTC part integrated into the
Freescale MC13783 PMIC and bases on patch created earlier by Sascha
Hauer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the Alarm support, this mode enabled when adding
IORESOURCE_IRQ to the platform device resources.
The patch also enables the wakeup mode, so the wakealarm sysfs file (under
/sys/class/rtc/rtcX/) can be used to configure the alarm clock.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add setting and clearing of the "pending" flag of the RTC alarm. The
semantics follow the UEFI specification 2.2 available at
http://www.uefi.org/specs/, i.e., the "pending" flag is cleared by
disabling the alarm, but not by any other condition (such as the passing
of time, a successful wakeup, or setting of a new alarm.)
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The to_platform_device macro itself uses container_of macro. Nested use
of container_of macro causes following sparse warnings:
rtc-ds1553.c:259:3: warning: symbol '__mptr' shadows an earlier one
rtc-ds1553.c:259:3: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Call dev_set_drvdata before rtc device creation.
- Use its own spinlock instead of rtc->irq_lock. Because pdata->rtc
must be initialized to use the irq_lock (pdata->rtc->irq_lock). There
is a small window which rtc methods can be called before pdata->rtc is
initialized.
And there is no need use the irq_lock to protect hardware registers.
The driver's own spinlock shoule be enough.
- Check pdata->rtc before calling rtc_update_irq.
- Use alarm_irq_enable and remove ioctl routine.
- Use devres APIs and simplify error/remove path.
These fixes are ported from ds1553 driver and just compile-tested only.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Call dev_set_drvdata before rtc device creation
* Use its own spinlock instead of rtc->irq_lock
* Check pdata->rtc before calling rtc_update_irq
* Use {alarm,update}_irq_enable and remove ioctl routine
* Use devres APIs and simplify error/remove path
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Use its own spinlock instead of rtc->irq_lock
* Check pdata->rtc before calling rtc_update_irq
* Disable interrupt after rtc_device_unregister
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Call dev_set_drvdata before rtc device creation.
- Use its own spinlock instead of rtc->irq_lock. Because pdata->rtc
must be initialized to use the irq_lock (pdata->rtc->irq_lock). There
is a small window which rtc methods can be called before pdata->rtc is
initialized.
And there is no need use the irq_lock to protect hardware registers.
The driver's own spinlock shoule be enough.
- Check pdata->rtc before calling rtc_update_irq.
- Use {alarm,update}_irq_enable and remove ioctl routine.
- Use devres APIs and simplify error/remove path.
These fixes are ported from ds1553 driver and just compile-tested only.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop ioctl function that handles RTC_AIE/RTC_UIE, and use instead the
rtc subsystem API (alarm_irq_enable/update_irq_enable callbacks).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Herton Ronaldo Krzesinski recently raised up, and fixed, an issue with the
rtc_cmos driver, which was referring to an inconsistent driver data.
This patch ensures that driver data registration happens before
rtc_device_register().
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Thomas Hommel <thomas.hommel@gefanuc.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Andrew Sharp <andy.sharp@onstor.com>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alexander Bigga <ab@mycable.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Mark Zhan <rongkai.zhan@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that rtc wont generate interrupts after a resume from disk.
Here hpet rtc emulation is used.
Problem is that rtc hpet comparator, isn't reinitialized after resume.
Easiest way to solve this, is always mask all hpet interrupts on suspend
This is triggered, when suspending with alarm set.
Otherwise, hpet driver will think it doesn't need to reinitialize
the rtc comparator, thus rtc interrupts won't work.
This emulation isn't need for wakealarm.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for RTC in phoenix TWL6030.
Register offset addresses have changed in TWL6030
rtc-twl.c will hence forth support all twl RTC (4030, 5030, 6030 ..)
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch renames all twl4030_ functions to twl_ so that RTC driver can be
shared between Triton and Phoenix.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Nayak Rajendra <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Bring the WM8350 IRQ API more in line with the generic IRQ API by
masking and unmasking interrupts as they are requested and freed.
This is mostly just a case of deleting the mask and unmask calls
from the individual drivers.
The RTC driver is changed to mask the periodic IRQ after requesting
it rather than only unmasking the alarm IRQ. If the periodic IRQ
fires in the period where it is reqested then there will be a
spurious notification but there should be no serious consequences
from this.
The CODEC drive is changed to explicitly disable headphone jack
detection prior to requesting the IRQs. This will avoid the IRQ
firing with no jack set up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is done as simple code transformation, the semantics of the
IRQ API provided by the core are are still very different to those
of genirq (mainly with regard to masking).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since platform_device_add_data copies the passed data, the allocated
subdev_pdata is never freed. A simple fix would be to either free subdev_pdata
or put it onto the stack. But since the pcf50633 child devices can rely on
beeing children of the pcf50633 core device it's much more elegant to get access
to pcf50633 core structure through that link. This allows to get completly rid
of pcf5033_subdev_pdata.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: parport_mfc3 - Not makes it a bool before the comparison.
m68k: don't export static inline functions
fbdev: atafb - add palette register check
m68k: Remove the BKL from sys_execve
m68k: Cleanup linker scripts using new linker script macros.
m68k: Make thread_info.h usable from assembly.
m68knommu: define arch_has_single_step() and friends
m68k: ptrace fixes
m68k: use generic code for ptrace requests
rtc: Add an RTC driver for the Ricoh RP5C01
rtc: Add an RTC driver for the Oki MSM6242
When detecting power failure, the probe function would reset the clock
time to defined state.
However, the clock's _date_ might still be bogus and a subsequent probe
fails when sanity-checking these values.
Change the power-failure fixup code to do a full setting of rtc_time,
including a valid date.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The possible CCR_Y2K register values are 19 or 20 and struct rtc_time's
tm_year is in years since 1900.
The function translating rtc_time to register values assumes tm_year to be
years since first christmas, though, and we end up storing 0 or 1 in the
CCR_Y2K register, which the hardware does not refuse to do.
A subsequent probing of the clock fails due to the invalid value range in
the register, though.
[ And if it didn't, reading the clock would yield a bogus year because
the function translating registers to tm_year is assuming a register
value of 19 or 20. ]
This fixes the conversion from years since 1900 in tm_year to the
corresponding CCR_Y2K value of 19 or 20.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"rtc" is freed and then dereferenced on the next line. This patch fixes
that.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function ds1302_rtc_remove is defined using __devexit, so don't use
__exit_p but __devexit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: linux-kernel@vger.kernel.org
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This will fix some small issues with the COH 901 331 RTC driver:
- Interrupt is disabled after alarm so that we don't fire
multiple interrupts.
- We return 0 from the coh901331_alarm_irq_enable() ridding
a compile warning.
- We alter the name in the U300 device registry to match that
of the driver so they sucessfully resolve.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
v3020_mmio_read_bit() always returns 0 when left_shift > 7.
v3020_mmio_read_bit()'s return type is (unsigned char). The code returns
a value masked by (1 << left_shift) that is casted to the return type. If
left_shift is larger than 7, the cast will always result in a 0 return
value. The problem was discovered with left_shift = 16, and the included
patch corrects the problem.
The bug was introduced in the last (Apr 3 2009) commit of the file, kernel
versions 2.6.30 and later.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Raphael Assenat <raph@8d.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/rtc/rtc-vr41xx.c: In function 'vr41xx_rtc_irq_set_freq':
drivers/rtc/rtc-vr41xx.c:217: warning: comparison of distinct pointer types lacks a cast
drivers/rtc/rtc-vr41xx.c:217: warning: right shift count >= width of type
drivers/rtc/rtc-vr41xx.c:217: warning: passing argument 1 of '__div64_32' from incompatible pointer type
include/asm-generic/div64.h:35: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to Documentation/rtc.txt, RTC_WKALM_SET sets the alarm time and
enables/disables the alarm. We implement RTC_WKALM_SET through
pcf50633_rtc_set_alarm. The enabling/disabling part was missing.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Reported-by: Michael 'Mickey' Lauer <mickey@openmoko.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCF50633 stores a month value of 1-12, but the kernel wants 0-11.
Signed-off-by: Rask Ingemann Lambertsen <rask@sygehus.dk>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A pointer to stk17ta8_rtc_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Hannes Eder <hannes@hanneseder.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
