When bonding enslaves non Ethernet devices it takes pointers to functions
in the module that owns the slaves. In this case it becomes unsafe
to keep the bonding master registered after last slave was unenslaved
because we don't know if the pointers are still valid. Destroying the bond when slave_cnt is zero
ensures that these functions be used anymore.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Delay sending a gratuitous_arp when LINK_STATE_LINKWATCH_PENDING bit
in dev->state field is on. This improves the chances for the arp packet to
be transmitted.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bonding sometimes uses Ethernet constants (such as MTU and address length) which
are not good when it enslaves non Ethernet devices (such as InfiniBand).
Signed-off-by: Moni Shoua <monis at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow to enslave devices when the bonding device is not up. Over the discussion
held at the previous post this seemed to be the most clean way to go, where it
is not expected to cause instabilities.
Normally, the bonding driver is UP before any enslavement takes place.
Once a netdevice is UP, the network stack acts to have it join some multicast groups
(eg the all-hosts 224.0.0.1). Now, since ether_setup() have set the bonding device
type to be ARPHRD_ETHER and address len to be ETHER_ALEN, the net core code
computes a wrong multicast link address. This is b/c ip_eth_mc_map() is called
where for multicast joins taking place after the enslavement another ip_xxx_mc_map()
is called (eg ip_ib_mc_map() when the bond type is ARPHRD_INFINIBAND)
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows for enslaving netdevices which do not support
the set_mac_address() function. In that case the bond mac address is the one
of the active slave, where remote peers are notified on the mac address
(neighbour) change by Gratuitous ARP sent by bonding when fail-over occurs
(this is already done by the bonding code).
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch changes some of the bond netdevice attributes and functions
to be that of the active slave for the case of the enslaved device not being
of ARPHRD_ETHER type. Basically it overrides those setting done by ether_setup(),
which are netdevice **type** dependent and hence might be not appropriate for
devices of other types. It also enforces mutual exclusion on bonding slaves
from dissimilar ether types, as was concluded over the v1 discussion.
IPoIB (see Documentation/infiniband/ipoib.txt) MAC address is made of a 3 bytes
IB QP (Queue Pair) number and 16 bytes IB port GID (Global ID) of the port this
IPoIB device is bounded to. The QP is a resource created by the IB HW and the
GID is an identifier burned into the HCA (i have omitted here some details which
are not important for the bonding RFC).
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_enable_device() is __must_check so do that in natsemi_resume().
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unless we have failed to fill the RX ring the timer used by the natsemi
driver is not particularly urgent and can use round_jiffies() to allow
grouping with other timers.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The call to napi_disable() in the PCI shutdown handler is problematic,
and is aggravated by the new NAPI.
Also, make sure watchdog timer doesn't go off.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
if your mask is host-endian, you should apply it after le64_to_cpu();
if it's little-endian - before. Doing both (for the same mask and
little-endian value) is broken.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
deal with signedness of the stuff passed to set_bit() et.al.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... since that sucker is not 32bit-only and on 64bit skb->tail is an
offset, not a pointer.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3d73c288 ("mlx4_core: Fix section mismatches") introduced a
stupid bug in device init: when some of mlx4_init_one() was split off
into __mlx4_init_one(), the call from the main mlx4_init_one()
function was back to mlx4_init_one() rather than to __mlx4_init_one(),
which leads to an obvious infinite loop if the function is every
called.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
b43 wireless needs <linux/io.h>
linux/drivers/net/wireless/b43/pio.h: In function 'b43_pio_write':
linux/drivers/net/wireless/b43/pio.h:89: error: implicit declaration of function 'mmiowb'
linux/drivers/net/wireless/b43/phy.c: In function 'b43_phy_write':
linux/drivers/net/wireless/b43/phy.c:301: error: implicit declaration of function 'mmiowb'
linuxdrivers/net/wireless/b43/sysfs.c: In function 'b43_attr_interfmode_store':
linuxdrivers/net/wireless/b43/sysfs.c:147: error: implicit declaration of function 'mmiowb'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
PM: merge device power-management source files
sysfs: add copyrights
kobject: update the copyrights
kset: add some kerneldoc to help describe what these strange things are
Driver core: rename ktype_edd and ktype_efivar
Driver core: rename ktype_driver
Driver core: rename ktype_device
Driver core: rename ktype_class
driver core: remove subsystem_init()
sysfs: move sysfs file poll implementation to sysfs_open_dirent
sysfs: implement sysfs_open_dirent
sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
sysfs: make sysfs_root a regular directory dirent
sysfs: open code sysfs_attach_dentry()
sysfs: make s_elem an anonymous union
sysfs: make bin attr open get active reference of parent too
sysfs: kill unnecessary NULL pointer check in sysfs_release()
sysfs: kill unnecessary sysfs_get() in open paths
sysfs: reposition sysfs_dirent->s_mode.
sysfs: kill sysfs_update_file()
...
A number of different drivers incorrect access the kobject name field
directly. This is not correct as the name might not be in the array.
Use the proper accessor function instead.
Need to read and store sblk->status_idx before checking for more work.
The status idx is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed. If the
order is reversed, we can end up acknowledging work we haven't
processed.
When completing bnx2_poll(), we should always break out of the while
loop and return work_done instead of returning 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to read and store sblk->status_tag before checking for more work.
The status tag is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed. If the
order is reversed, we can end up acknowledging work we haven't
processed.
When we detect tx error, it is more correct to return the rx
work_done so far instead of 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug caused by the recent APE support added for 5761
devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to keep track of new changes.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use builtin statistics structure from net device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put initialization in sequential order (same as other constants).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure PCI register for PHY power gets set correctly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure and not dump reserved areas of device space.
Touching some of these causes machine check exceptions on boards
like D-Link DGE-550SX.
Coding note, used a complex switch statement rather than bitmap
because it is easier to relate the block values to the documentation
rather than looking at a encoded bitmask.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
mlx4_core: Fix section mismatches
IPoIB: Allow setting policy to ignore multicast groups
IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
IB/ipath: Remove redundant link state checks
IB/ipath: Fix IB_EVENT_PORT_ERR event
IB/ipath: Better handling of unexpected GPIO interrupts
IB/ipath: Maintain active time on all chips
IB/ipath: Fix QHT7040 serial number check
IB/ipath: Indicate a couple of chip bugs to userspace
IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
IB/ipath: Remove duplicate copy of LMC
IB/ipath: Add ability to set the LMC via the sysfs debugging interface
IB/ipath: Optimize completion queue entry insertion and polling
IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
IB/ipath: Generate flush CQE when QP is in error state
IB/ipath: Remove redundant code
IB/ipath: Future proof eeprom checksum code (contents reading)
IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
...
Handle the corner case where budget is exhausted correctly.
And save unnecessary read of index register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():
/* Drivers must not modify the NAPI state if they
* consume the entire weight. In such cases this code
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.
BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update to version 3.83.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables WOL by default if out-of-box WOL is enabled in the
NVRAM.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rest of the miscellaneous code required to support the
5761.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the new APE block, present in 5761 chips.
APE stands for Application Processing Engine. The primary function of
the APE is to process manageability traffic, such as ASF.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new 5761-specific NVRAM strapping decode routine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default WoL setting to match the NVRAM's setting. It
always defaulted to WoL disabled before and caused a lot of confusion
for users.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote PHY media type and link status can change between
->probe() and ->open(). For correct operation, we need to get the
new status again during ->open().
The ethtool link test and loopback test are also fixed to work with
remote PHY. PHY loopback is simply skipped when remote PHY is
present.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct
net_device objects.") changed the interface to NAPI polling. Fix up
the ibm_newemac driver so that it works with this new interface. This
is actually a nice cleanup because ibm_newemac is one of the drivers
that wants to have multiple NAPI structures for a single net_device.
Compile-tested only as I don't have a system that uses the ibm_newemac
driver. This conversion the conversion for the ibm_emac driver that
was tested on real PowerPC 440SPe hardware.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct
net_device objects.") changed the interface to NAPI polling. Fix up
the ibm_emac driver so that it works with this new interface. This is
actually a nice cleanup because ibm_emac is one of the drivers that
wants to have multiple NAPI structures for a single net_device.
Tested with the internal MAC of a PowerPC 440SPe SoC with an AMCC
'Yucca' evaluation board.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The natsemi driver has a define NATSEMI_TIMER_FREQ which looks like it
controls the normal frequency of the chip poll timer but in fact only
takes effect for the first run of the timer. Adjust the value of the
define to match that used by the timer and use the define consistently.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
