The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GUI idle interrupts don't seem to work terribly well on r500 and earlier,
so let's use a fence instead.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to handle the ring while we've already locked it, so split out
the allocation and commit functions in order to allow them to be used.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- disable gui idle interrupt use
Seems to hang some r5xx chips
- move vbl range check into
existing vbl check function in
radeon_pm.c
- disable crtc mc acccess for the
whole reclocking process
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This seems to be relatively stable now, so enable it for these chipsets
too.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vblank interrupt on r600 doesn't seem to be especially reliable, so
perform some sanity checks before the actual reclock.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm code could take vram_mutex followed by cp_mutex, while the
reclocking code would do the reverse. Hilarity could ensue.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to choose the correct PM state to transition into before starting
the actual change. Call radeon_get_power_state() at the top of the clock
setting to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With luck, dynamic memory reclocking on r600 should be stable with
the previous patches. Enable it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm bo workqueue may touch objects while we're reclocking, so make
sure it's blocked until we're done.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to block the drm core from doing anything that may touch our vram
during reclock, so take the drm mutex for the duration.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Touching vram while the card is reclocking can lead to lockups. Unmap
any pages that could be touched by the CPU and block any accesses to
vram until the reclocking is complete.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's a moderate amount of effort involved in setting the card up for
clock transitions, so unify the codepaths to make it easier to implement.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add two new sysfs attributes:
- dynpm
- power_state
Echoing 0/1 to dynpm disables/enables dynamic power management.
The driver scales the sclk dynamically based on the number of
queued fences. dynpm only scales sclk dynamically in single head
mode.
Echoing x.y to power_state selects a static power state (x) and clock
mode (y). This allows you to statically select a power state and clock
mode. Selecting a static clock mode will disable dynpm.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- pm_misc() - handles voltage, pcie lanes, and other non
clock related power mode settings. Currently disabled.
Needs further debugging
- pm_prepare() - disables crtc mem requests right now.
All memory clients need to be disabled when changing
memory clocks. This function can be expanded to include
disabling fb access as well.
- pm_finish() - enable active memory clients.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- remove non_clock_info struct
- track power state misc flags
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just adds overhead when the power state will never change.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Hook the atom table parsing up to module loading, so we can automatically
load the appropriate hwmon drivers.
Based on initial patch for r6xx from Matthew Garrett
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This also simplifies the code and enables reclocking with multiple heads
active by tracking whether the power states are single or multi-head
capable.
Eventually, we will want to select a power state based on external
factors (AC/DC state, user selection, etc.).
(v2) Update for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On pre-r6xx, the power mode array is usually ordered:
low
...
high
default
On r6xx+:
default
low
...
high
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
set proper wait condition as noted by Rafał Miłecki.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Useful for certain power management operations. You
need to wait for the GUI engine (2D, 3D, CP, etc.) to be
idle before changing clocks or adjusting engine parameters.
(v2) Fix gui idle enable on pre-r6xx asics
(v3) The gui idle interrrupt status bit is permanently asserted
on pre-r6xx chips, but the interrrupt is still generated.
workaround it in the driver.
(v4) Add support for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check to see if the GUI engine and related blocks
(2D, 3D, CP, etc) are idle or not. There are a number
of cases when we need to know if the drawing engine
is busy.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It removes a hack from nouveau code which had to detect which
region to pass to kick vesafb/efifb.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace need to know the hw crtc id (0, 1, 2, ...) from the drm
crtc id. Bump the minor version so userspace can enable conditionaly
features depend on this.
V2 use num_crtc and avoid DRM_ERROR
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes LVDS issues on some laptops; notably laptops with
2048x1536 panels.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we just set them to dpms off. This should save
additional power.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previous reset code leaded to computer hard lockup (need to unplug
the power too reboot the computer) on various configuration. This
patch change the reset code to avoid hard lockup. The GPU reset
is failing most of the time but at least user can log in remotely
or properly shutdown the computer.
Two issues were leading to hard lockup :
- Writting to the scratch register lead to hard lockup most likely
because the write back mecanism is in fuzy state after GPU lockup.
- Resetting the GPU memory controller and not reinitializing it
after leaded to hard lockup. We did only reinitialize in case of
successfull reset thus unsuccessfull reset quickly leaded to hard
lockup.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Implements irq support for HDMI audio output. Now the polling timer
is only enabled if irq support isn't available.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rework HDMI audio polling timer, only enable it when
at least one HDMI encoder needs it. Preparation for
replacing it with irq support.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-ttm-unmappable:
drm/radeon/kms: enable use of unmappable VRAM V2
drm/ttm: remove io_ field from TTM V6
drm/vmwgfx: add support for new TTM fault callback V5
drm/nouveau/kms: add support for new TTM fault callback V5
drm/radeon/kms: add support for new fault callback V7
drm/ttm: ttm_fault callback to allow driver to handle bo placement V6
drm/ttm: split no_wait argument in 2 GPU or reserve wait
Conflicts:
drivers/gpu/drm/nouveau/nouveau_bo.c
This patch enable the use of unmappable VRAM thanks to
previous TTM infrastructure change.
V2 update after io_mem_reserve/io_mem_free callback balancing
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All TTM driver have been converted to new io_mem_reserve/free
interface which allow driver to choose and return proper io
base, offset to core TTM for ioremapping if necessary. This
patch remove what is now deadcode.
V2 adapt to match with change in first patch of the patchset
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 adjust to minor cleanup
V5 remove the needs ioremap flag
V6 keep the ioremapping facility in TTM
[airlied- squashed driver removals in here also]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback and also the
infrastructure for supporting unmappable VRAM.
V2 validate BO with no_wait = true
V3 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V4 update to splitted no_wait ttm change
V5 update to new balanced io_mem_reserve/free change
V6 callback is responsible for iomapping memory
V7 move back iomapping to ttm
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher