If an array was created with --assume-clean we will oops when trying to
set ->resync_max.
Fix this by initializing ->recovery_wait in mddev_find.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the initial array synchronization process there is a window between
when a prexor operation is scheduled to a specific stripe and when it
completes for a sync_request to be scheduled to the same stripe. When
this happens the prexor completes and the stripe is unconditionally marked
"insync", effectively canceling the sync_request for the stripe. Prior to
2.6.23 this was not a problem because the prexor operation was done under
sh->lock. The effect in older kernels being that the prexor would still
erroneously mark the stripe "insync", but sync_request would be held off
and re-mark the stripe as "!in_sync".
Change the write completion logic to not mark the stripe "in_sync" if a
prexor was performed. The effect of the change is to sometimes not set
STRIPE_INSYNC. The worst this can do is cause the resync to stall waiting
for STRIPE_INSYNC to be set. If this were happening, then STRIPE_SYNCING
would be set and handle_issuing_new_read_requests would cause all
available blocks to eventually be read, at which point prexor would never
be used on that stripe any more and STRIPE_INSYNC would eventually be set.
echo repair > /sys/block/mdN/md/sync_action will correct arrays that may
have lost this race.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This addresses other oopsing paths in "spidev" by changing how it manages
refcounting. It decouples the lifecycle of the per-device data from the
class device (not just the spi device):
- Use class_{create,destroy} not class_{register,unregister}.
- Use device_{create,destroy} not device_{register,unregister}.
- Free the per-device data only when TWO conditions are true:
* Driver is unbound from underlying SPI device, and
* Device is no longer open (new)
Also, spi_{get,set}_drvdata not dev_{get,set}_drvdata for simpler code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SM/SMA traps received by the ipath driver should be forwarded to the
SM if it is running on the host. The ib_ipath driver was incorrectly
replying with "bad method."
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The low-level interrupt handler on s390 checks for _TIF_WORK_INT and
exits the guest context, if work is pending.
TIF_WORK_INT is defined as_TIF_SIGPENDING | _TIF_NEED_RESCHED |
_TIF_MCCK_PENDING. Currently the sie loop checks for signals and
reschedule, but it does not check for machine checks. That means that
we exit the guest context if a machine check is pending, but we do not
handle the machine check.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Fairly simple. "dev_use" was being allocated as a zero length array
because of bad math on 64-bit systems, causing a crash in
find_first_zero_bit(). One-liner follows:
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alias brd to rd in the hope of helping legacy users. Suggested by Jan.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't need to reserve "unset" resources. Trying to reserve
them results in messages like this, which are ugly but harmless:
system 00:08: iomem range 0x0-0x0 could not be reserved
Future PNP patches will remove use of IORESOURCE_UNSET, but
we still need it for now.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering:
fixlet to a57c1bade5 libata-sff:
Fix oops reported in kerneloops.org for pnp devices with no ctl
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check that tda827x_config is defined before attempting to use it.
Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On the TDA18271HD/C1, we perform RF tracking filter correction for VHF low
band, only. If supplied a frequency out of range, the error must be returned
to the caller (tda18271c1_rf_tracking_filter_calibration) so that it can
decide whether or not to write to register EB14, RFC_CPROG[7:0]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Testing whether xceive_pin is non-zero is not good enough as 0 is a valid
value. Instead explicitly test whether the Xceive tuner is used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is patch for fix data structure in querycap syscall.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-tip testing found the following build failure:
LD .tmp_vmlinux1
drivers/built-in.o: In function `generic_set_freq':
tuner-xc2028.c:(.text+0xbd896): undefined reference to `request_firmware'
tuner-xc2028.c:(.text+0xbdd7a): undefined reference to `release_firmware'
drivers/built-in.o: In function `xc_load_fw_and_init_tuner':
xc5000.c:(.text+0xc68e6): undefined reference to `request_firmware'
xc5000.c:(.text+0xc6abe): undefined reference to `release_firmware'
with this config:
http://redhat.com/~mingo/misc/config-Tue_May_20_18_11_34_CEST_2008.bad
the reason is another kconfig tool bug that has to be worked around in
the driver's Kconfig file: if FW_LOADER is selected in a second
dependency, that is not properly propagated up the dependencies.
in this case, FW_LOADER is selected from MEDIA_TUNER_XC2028:
config MEDIA_TUNER_XC2028
tristate "XCeive xc2028/xc3028 tuners"
depends on VIDEO_MEDIA && I2C
depends on HOTPLUG
select FW_LOADER
which got selected by MEDIA_TUNER:
config MEDIA_TUNER
tristate
default VIDEO_MEDIA && I2C
depends on VIDEO_MEDIA && I2C
select FW_LOADER if !MEDIA_TUNER_CUSTOMIZE && HOTPLUG
but the kconfig tool did not pick up this second-order dependency and
allowed CONFIG_FW_LOADER=m to be selected - in which case the build
fails.
the workaround i found was to move the select of FW_LOADER one level up,
so that the buggy kconfig tool can notice it and can act appropriately.
This problem can probably be worked around in other ways as well, i went
for the minimal fix.
Obviously, the kconfig tool should be fixed, it is not reasonable to
expect driver authors to do manual dependency resolution (that kconfig
itself already does) and uglify the Kconfig files. The kconfig tool did
nothing to warn about this situation and did not prevent this faulty
.config from being constructed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
direct dereferencing from user-supplied address
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Endianness annotations and fixes + fixing the handling of
->uncorrected_block_count
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use a standard method to manage multiple instances of a hybrid tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Create a macro to report the number of instances of the tuner driver
currently in use. This will allow drivers to perform specific cleanups
before destroying the last instance of a tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The gpio_dir/val statics cannot be global, they are card-specific.
Thanks to Andy Walls for pointing this out.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I always assumed that the Compro H900 could do digital as well,
but it turned out that it is an analog-only card.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The HVR-1600 can do both analog and digital capture at the same time.
Due to a driver bug -EBUSY would be returned when attempting to setup an
analog capture while a digital capture was already in progress.
Separate the two internally.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The handling of the audio registers 808 and 80c were based on old datasheets.
Updated to the latest information.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner_warn() macro relies on the local variable "priv" to be a valid
pointer. There was a case in simple_tuner_attach() where this cannot be the
case yet, so tuner_warn() would dereference a NULL "priv" pointer. Changed
the tuner_warn() to a printk() with the originally intended output format.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This code is irrelevant to this driver and should be removed. This was
copied from a hack in cx88-dvb.c, which prevents noise coming from the
analog tuner (via an audio patch cable from the pci card to the sound
hardware) when in digital mode by muting the tda988x. This issue does
not apply to this USB hybrid chip design, where a single piece of
silicon handles both analog and digital demodulation.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
somebody forgot to to fix this header...
Thanks to Ingo Molnar for pointing this out.
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
testing of the -tip tree found the following build failures on
2.6.26-rc3:
drivers/built-in.o: In function `ttusb_dec_disconnect':
ttusb_dec.c:(.text+0xa2c95): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `dvb_usb_read_remote_control':
dvb-usb-remote.c:(.text+0xa6a94): undefined reference to `input_event'
with this config:
http://redhat.com/~mingo/misc/config-Tue_May_20_03_48_57_CEST_2008.bad
these are due to the media/dvb/usb layer having dependencies on INPUT
functionality, without having that spelled out in the Kconfig file.
this patch makes that dependency explicit (for the drivers affected),
which solves the build error.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After commit 039d40019f
(V4L/DVB (7898): Fix VIDEO_MEDIA Kconfig logic)
VIDEO_MEDIA is no longer usable in Makefile's for deciding
which directories we enter, resulting in compile errors like the
following with CONFIG_VIDEO_DEV=y, CONFIG_DVB_CORE=m:
<-- snip -->
...
MODPOST 187 modules
...
make[2]: *** [__modpost] Error 1
<-- snip -->
The easiest solution is to always enter video/
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It doesn't seem to be intended that "tuner_modu_type" and
"MXL5005_ControlName" were global variables.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
check_v4l2 always returns 0, so this change is an noop for now,
but a comment says it will return something else in the future
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
change check_mode and set_mode to return negative errors and fix all callers
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
locking-add-typecheck-on-irqsave-and-friends-for-correct-flags.patch will cause
drivers/media/video/zoran_driver.c: In function 'zoran_close_end_session':
drivers/media/video/zoran_driver.c:1172: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now it returns the 0 if cmdlineparse not supplied.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
l2tp: Fix possible oops if transmitting or receiving when tunnel goes down
tcp: Fix for race due to temporary drop of the socket lock in skb_splice_bits.
tcp: Increment OUTRSTS in tcp_send_active_reset()
raw: Raw socket leak.
lt2p: Fix possible WARN_ON from socket code when UDP socket is closed
USB ID for Philips CPWUA054/00 Wireless USB Adapter 11g
ssb: Fix context assertion in ssb_pcicore_dev_irqvecs_enable
libertas: fix command size for CMD_802_11_SUBSCRIBE_EVENT
ipw2200: expire and use oldest BSS on adhoc create
airo warning fix
b43legacy: Fix controller restart crash
sctp: Fix ECN markings for IPv6
sctp: Flush the queue only once during fast retransmit.
sctp: Start T3-RTX timer when fast retransmitting lowest TSN
sctp: Correctly implement Fast Recovery cwnd manipulations.
sctp: Move sctp_v4_dst_saddr out of loop
sctp: retran_path update bug fix
tcp: fix skb vs fack_count out-of-sync condition
sunhme: Cleanup use of deprecated calls to save_and_cli and restore_flags.
xfrm: xfrm_algo: correct usage of RIPEMD-160
...
Some problems have been experienced in the field which cause an oops
in the pppol2tp driver if L2TP tunnels fail while passing data.
The pppol2tp driver uses private data that is referenced via the
sk->sk_user_data of its UDP and PPPoL2TP sockets. This patch makes
sure that the driver uses sock_hold() when it holds a reference to the
sk pointer. This affects its sendmsg(), recvmsg(), getname(),
[gs]etsockopt() and ioctl() handlers.
Tested by ISP where problem was seen. System has been up 10 days with
no oops since running this patch. Without the patch, an oops would
occur every 1-2 days.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an L2TP daemon closes a tunnel socket while packets are queued in
the tunnel's reorder queue, a kernel warning is logged because the
socket is closed while skbs are still referencing it. The fix is to
purge the queue in the socket's release handler.
WARNING: at include/net/sock.h:351 udp_lib_unhash+0x41/0x68()
Pid: 12998, comm: openl2tpd Not tainted 2.6.25 #8
[<c0423c58>] warn_on_slowpath+0x41/0x51
[<c05d33a7>] udp_lib_unhash+0x41/0x68
[<c059424d>] sk_common_release+0x23/0x90
[<c05d16be>] udp_lib_close+0x8/0xa
[<c05d8684>] inet_release+0x42/0x48
[<c0592599>] sock_release+0x14/0x60
[<c059299f>] sock_close+0x29/0x30
[<c046ef52>] __fput+0xad/0x15b
[<c046f1d9>] fput+0x17/0x19
[<c046c8c4>] filp_close+0x50/0x5a
[<c046da06>] sys_close+0x69/0x9f
[<c04048ce>] syscall_call+0x7/0xb
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the Philips CPWUA054/00 in p54usb.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there are no networks on the free list, expire the oldest one when
creating a new adhoc network. Because ipw2200 and the ieee80211 stack
don't actually cull old networks and place them back on the free list
unless they are needed for new probe responses, over time the free list
would become empty and creating an adhoc network would fail due to the !
list_empty(...) check.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: space prohibited between function name and open parenthesis '('
#22: FILE: drivers/net/wireless/airo.c:2907:
+ while ((IN4500 (ai, COMMAND) & COMMAND_BUSY) && (delay < 10000)) {
total: 0 errors, 1 warnings, 8 lines checked
./patches/wireless-airo-waitbusy-wont-delay.patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Dan Williams <dcbw@redhat.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a kernel crash on rmmod, in the case where the controller
was restarted before doing the rmmod.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of local_irq_save and local_irq_restore rather then the
deprecated save_and_cli and restore_flags calls.
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 64e9159f5d ("serial_core:
uart_set_ldisc infrastructure") introduced the ability for low-level
serial drivers to be informed when the tty ldisc changes.
However, the actual tty-layer function that does this callback for
serial devices was declared with the wrong type, having a spurious and
unused 'ldisc' argument.
This fixed the resulting compiler warning by just removing it.
Acked-by: Blithering Idiot <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata-sff: Fix oops reported in kerneloops.org for pnp devices with no ctl
libata: kill unused constants
sata_mv: PHY_MODE4 cleanups
[libata] ata_piix: more acer short cable quirks
[libata] ACPI: Properly handle bay devices in dock stations
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qla2xxx: Update version number to 8.02.01-k4.
[SCSI] qla2xxx: Correct handling of AENs postings for vports.
[SCSI] qla2xxx: Revert "qla2xxx: Use proper HA during asynchronous event handling."
[SCSI] ibmvscsi: Non SCSI error status fixup
[SCSI] fusion mpt: fix target missing after resetting external raid
[SCSI] fix intermittent oops in scsi_bus_uevent
[SCSI] qla2xxx: Update version number to 8.02.01-k3.
[SCSI] qla2xxx: Revert "qla2xxx: Validate mid-layer 'underflow' during check-condition handling."
[SCSI] qla2xxx: Disable local-interrupts while polling for RISC status.
[SCSI] qla2xxx: Extend the 'fw_dump' SYSFS node the ability to initiate a firmware dump.
[SCSI] qla2xxx: Don't depend on mailbox return values while enabling FCE tracing.
[SCSI] qla2xxx: Convert vport_sem to a mutex
[SCSI] qla2xxx: firmware semaphore to mutex
[SCSI] qla2xxx: Correct locking within MSI-X interrupt handlers.
[SCSI] qla2xxx: Display driver version at module init-time.
[SCSI] qla2xxx: Return correct port_type to FC-transport for Vports.
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdbts: Use HW breakpoints with CONFIG_DEBUG_RODATA
kgdb: use common ascii helpers and put_unaligned_be32 helper
* wMaxPacketSize is le16; copying it to a field of local structure and then
using that field as host-endian (size of object to be allocated) is broken.
* bMaxPacketSize0 is 8-bit; feeding it to le16_to_cpu() is bogus and since the
result is used as host-endian, it's not even misspelled cpu_to_le16().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it
Add
ata_sff_irq_status - encapsulates the IRQ check logic
This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that
ata_sff_sync - ensure writes hit the device
Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.
- ata_sff_pause - 400nS delay
Ensure the command hit the device and delay 400nS
- ata_sff_dma_pause
Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)
The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The handling for PHY_MODE4 was originally just cloned from the
Marvell proprietary driver (with their blessing).
But we can do better than that.
Tidy things up with some judicious mask definitions, to improve maintainability.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ICH6 on ACER Aspire 1694WLMi to list of laptops that use short cables
rather than 80 wire
OriginalAuthor: Tiago Sousa
OriginalLocation: http://launchpadlibrarian.net/11627664/new.ich_laptop.short.cables.diff
Bug: #187121
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Differentiate between bay devices in dock stations and others:
- When an ACPI_NOTIFY_EJECT_REQUEST appears, just signal uevent to
userspace (that is when the optional eject button on a bay device is
pressed/pulled) giving the possibility to unmount file systems and to
clean up. Also, only send uevent in case we get an EJECT_REQUEST
without doing anything else. In other cases, you'll get an add/remove
event because libata attaches/detaches the device.
- In case of a dock event, which in turn signals an
ACPI_NOTIFY_EJECT_REQUEST, immediately detach the device, because it
may already have been gone
* In case of an ACPI_NOTIFY_DEVICE/BUS_CHECK, evaluate _STA to check if
the device has been plugged or unplugged. If plugged, hotplug it, if
unplugged, just signal event to userspace
(initial patch by Matthew Garrett <mjg59@srcf.ucam.org>)
* Call ACPI _EJ0 for detached devices
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The tty layer provides a callback that is used when the line discipline
is changed. Some hardware uses this to configure hardware specific
features such as IrDA mode on serial ports. Unfortunately the serial
layer does not provide this feature or pass it down to drivers.
Blackfin used to hack around this by rewriting the tty ops, but those are
now properly shared and const so the hack fails. Instead provide the
proper operations.
This change plus a follow up from the Blackfin guys is needed to avoid
blackfin losing features in this release.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both the PNP/PCI conflict detection quirk and the PNP system
driver must use the same mechanism to mark resources as disabled.
I think it's best to keep the resource and to keep the type bit
(IORESOURCE_MEM, etc), so that we match the list from firmware
as closely as possible.
Fixes this regression from 2.6.25: http://lkml.org/lkml/2008/6/1/82
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Tested-by: Avuton Olrich <avuton@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
8250 Serial Driver: revert extra IRQ flag definition patch
Blackfin arch: update anomaly headers from toolchain trunk
Blackfin arch: Remove bad and usless code
Blackfin arch: Fix bug - set corret SSEL and IRQ to enable AD7877 on BF527
Blackfin arch: Fix typo. it should be _outsw_8
Blackfin arch: Cleanup no functional changes
As Russell pointed out, original patch will break some serial configurations
because of the dependency of the <asm/serial.h> header file.
Revert it first and try to find out other solution later
Cc: Javier Herrero <jherrero@hvsistemas.es>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The following patch is seems to fix the tulip suspend/resume panic:
http://bugzilla.kernel.org/show_bug.cgi?id=8952#c46
My attempts at a cleaner patch failed and Pavel thinks this is OK.
Original from: kernelbugs@tap.homeip.net
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When using 4+ GB RAM and SWIOTLB is active, the driver corrupts
memory by writing an skb after the relevant DMA page has been
unmapped. Although this doesn't happen when *not* using bounce
buffers, clearing the pointer to the DMA page after unmapping
it fixes the problem.
http://marc.info/?t=120861317000005&r=2&w=2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Because we cache the last failed-to-xmit packet, if there are no
packets queued behind that one we may never send it (reproduced here
as TCP stalls, "cured" by an outgoing ping).
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If we fail to transmit a packet, we assume the queue is full and put
the skb into last_xmit_skb. However, if more space frees up before we
xmit it, we loop, and the result can be transmitting the same skb twice.
Fix is simple: set skb to NULL if we've used it in some way, and check
before sending.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 5a0a92e67b mentions len < ETH_ZLEN
is true for ARP packets. This obviously is not unlikely.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After request_dma() succeeding, any error path should do free_dma().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is normal when the external link is down so don't report it as an error.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Initialize all proper structure members in order to support
work-list vport processing. This code also properly acquires the
correct (physical hardware_lock) lock during work submission.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts commit bd2a1846b2.
The original (prior to the reverted commit) code was correct.
Additionally, the vp_idx should be checked during MBA_PORT_UPDATE
in order for proper handling to take place for a given vport.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: notify on empty
virtio: force callback on empty.
virtio_blk: fix endianess annotations
virtio_config: fix len calculation of config elements
virtio_net: another race with virtio_net and enable_cb
virtio: An entropy device, as suggested by hpa.
virtio_blk: allow read-only disks
lguest: fix ugly <NULL> in /proc/interrupts
virtio: set device index in common code.
virtio: virtio_pci should not set bus_id.
virtio: bus_id for devices should contain 'virtio'
Fix crash in virtio_blk during modprobe ; rmmod ; modprobe
lguest: use ioremap_cache, not ioremap
* Wim Van Sebroeck <wim@iguana.be> wrote:
> Author: Jordan Crouse <jordan.crouse@amd.com>
> Date: Mon Jan 21 10:07:00 2008 -0700
>
> [WATCHDOG] Add a watchdog driver based on the CS5535/CS5536 MFGPT timers
-tip testing found the following build failure on latest -git:
drivers/watchdog/geodewdt.c: In function 'geodewdt_probe':
drivers/watchdog/geodewdt.c:225: error: too many arguments to function 'geode_mfgpt_alloc_timer'
make[1]: *** [drivers/watchdog/geodewdt.o] Error 1
make: *** [drivers/watchdog/geodewdt.o] Error 2
with this config:
http://redhat.com/~mingo/misc/config-Fri_May_30_15_19_52_CEST_2008.bad
find the fix below.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When Greg "fixed" the sysfs usage of that driver a while back, he seem
to have introduced a bug where the quotes are added around the name of
our specific sysfs files, thus breaking the user space tool.
This fixes it. Tested DLPAR operations on a POWER6 machine successfully.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c,
as the actual PCI IDs deployed in the field differed from the forecasted ones
preemptively placed in the driver.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following commit (4c9bf4e799):
libata: replace tf_read with qc_fill_rtf for non-SFF drivers
Broke the sata_fsl.c driver in 2.6.26-rc. I know the following patch fixes
the issue, it clearly also adds port multipler support. The current
2.6.26-rc driver is broken.
On boot with debug enabled we get something like (w/o this patch):
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
.. continues for ever.
This change fixes this as a side effect of adding port multiplier support.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As in sil4726, SRST can't be trusted on sil3726 causing detection
problems under certain configuraitons. I thought it was from the
Config Disk device but apparently not.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix libata-scsi kernel-doc notation:
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1659): No description found for parameter 'cmd'
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1971): No description found for parameter 'buf'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ICH8M on macbooks are peculiar in that some of them lock up when the
second port is enabled, some return bogus values on SIDPR access while
yet others hang on SIDPR access. Also, the ich8m_apple_sata entry was
wrongly added below generic ich8m entry making it virtually useless.
This patch works around macbook ich8m problems by
* moving ich8m_apple_sata entry above generic ich8m entry
* dropping PIIX_FLAG_SIDPR from ich8m_apple_sata
* adding subsystem 106b:00a1 as ich8m_apple_sata
Reported and tested by MATSUBAYASHI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: MATSUBAYASHI 'Shaolin' Kohji <shaolin@rhythmaning.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 5182 System-On-Chip (SOC) variant wants certain lower
bits to be cleared on any write to the PHY_MODE3 register.
If/when support is added for other SOC variants, we'll need
some way to uniquely identify the 5182, and not perform this
workaround for the others.
But for now, it is the only SOC variant we support here.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The "B2" variant of the 6041/6081 (genII) chips requires
that the PHY_MODE3 register be rewritten after any write
to PHY_MODE4.
This fixes a regression introduced by an earlier patch.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The only public release of the 6042/7042 chips was/is revision "B0".
Remove code that attempted to deal with earlier, non-released revs.
This matches the logic of the current Marvell "proprietary" driver.
Also, bump up the sata_mv version number, to reflect this batch of erratas.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix and update the errata handling for the PHY_MODEx registers.
This improves receiver noise tolerance, among other things.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert the System-on-Chip flag from a host flag to an hpriv flag,
for better consistency with other chip-rev flags, and for easier use
in errata fixes etc.
Also change the related "HAS_PCI()" into "!IS_SOC()" for better consistency
of naming/use (everything else SOC-related already uses "SOC").
There are no functionality changes in this patch.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Update default configuration.
[S390] disassembler: fix idte instruction format.
[S390] tape: fix race with stack local wait_queue_head_t.
[S390] 3270: fix race with stack local wait_queue_head_t.
[S390] dasd: use a generic wait_queue for sleep_on
[S390] sclp_vt220: fix scheduling while atomic bug.
[S390] showmem: Only walk spanned pages.
[S390] appldata: prevent cpu hotplug when walking cpu_online_map.
[S390] Fix section mismatch warnings.
[S390] s390 types: make dma_addr_t 64 bit capable
[S390] tape: Fix race condition in tape block device driver
[S390] fix sparsemem related compile error with allnoconfig on s390
In this case we want a constant pointer to constant chars:
drivers/misc/thinkpad_acpi.c:3824:19: error: Just how const do you want this type to be?
Like the error says.
drivers/misc/thinkpad_acpi.c:3863:19: error: Just how const do you want this type to be?
drivers/misc/thinkpad_acpi.c:3864:19: error: Just how const do you want this type to be?
drivers/misc/thinkpad_acpi.c:3865:19: error: Just how const do you want this type to be?
drivers/misc/thinkpad_acpi.c:3866:19: error: Just how const do you want this type to be?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code would try to free 'report' twice upon input_register_device()
failure.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A wait_event call with a stack local wait_queue_head_t structure that is
used to do the wake up for the wait_event is inherently racy. After the
wait_event finished the wake_up call might not have completed yet.
Replace the stack local wait_queue_head_t in tape_do_io and
tape_do_io_interruptible with a per device wait queue.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A wait_event call with a stack local wait_queue_head_t structure that is
used to do the wake up for the wait_event is inherently racy. After the
wait_event finished the wake_up call might not have completed yet.
Remove the stack local wait_queue_head_t from raw3270_start_init and
use the global raw3270_wait_queue instead.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use a generic wait_queue to prevent the wait_queue in dasd_sleep_on_
functions from being referenced by callback_data while it does not
exist any more.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The driver incorrectly assumed that putchar will only be called from
schedulable process context and therefore blocked and waited if no
free output buffers where available.
Since putchar may also be called from BH context this may lead to
deadlocks.
To fix this just return the number of characters accepted and let the
upper layer handle the rest.
The console write function will busy wait (sclp_sync_wait) until a
buffer is available again.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This fixes the last remaining section mismatch warnings in s390
architecture code. It reveals also a real bug introduced by... me
with git commit 2069e978d5
("[S390] sparsemem vmemmap: initialize memmap.")
Calling the generic vmemmap_alloc_block() function to get initialized
memory is a nice idea, however that function is __meminit annotated
and therefore the function might be gone if we try to call it later.
This can happen if a DCSS segment gets added.
So basically revert the patch and clear the memmap explicitly to fix
the original bug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Due to incorrect function call sequence it can happen that a tape block
request is finished before the request is taken from the block request queue.
The following sequence leads to that condition:
* tapeblock_start_request() -> start CCW program
* Request finishes -> IO interrupt
* tapeblock_end_request()
* end_that_request_last()
If blkdev_dequeue_request() has not been called before end_that_request_last(),
a kernel bug is triggered in end_that_request_last() because the request is
still queued. To solve that problem blkdev_dequeue_request() has to be called
before starting the CCW program.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
virtio allows drivers to suppress callbacks (ie. interrupts) for
efficiency (no locking, it's just an optimization).
There's a similar mechanism for the host to suppress notifications
coming from the guest: in that case, we ignore the suppression if the
ring is completely full.
It turns out that life is simpler if the host similarly ignores
callback suppression when the ring is completely empty: the network
driver wants to free up old packets in a timely manner, and otherwise
has to use a timer to poll.
We have to remove the code which ignores interrupts when the driver
has disabled them (again, it had no locking and hence was unreliable
anyway).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Hello Rusty,
seems that we still have a problem with virtio_net and the enable_cb callback.
During a long running network stress tests with virtio and got the following
oops:
------------[ cut here ]------------
kernel BUG at drivers/virtio/virtio_ring.c:230!
illegal operation: 0001 [#1] SMP
Modules linked in:
CPU: 0 Not tainted 2.6.26-rc2-kvm-00436-gc94c08b-dirty #34
Process netserver (pid: 2582, task: 000000000fbc4c68, ksp: 000000000f42b990)
Krnl PSW : 0704c00180000000 00000000002d0ec8 (vring_enable_cb+0x1c/0x60)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 EA:3
Krnl GPRS: 0000000000000000 0000000000000000 000000000ef3d000 0000000010009800
0000000000000000 0000000000419ce0 0000000000000080 000000000000007b
000000000adb5538 000000000ef40900 000000000ef40000 000000000ef40920
0000000000000000 0000000000000005 000000000029c1b0 000000000fea7d18
Krnl Code: 00000000002d0ebc: a7110001 tmll %r1,1
00000000002d0ec0: a7740004 brc 7,2d0ec8
00000000002d0ec4: a7f40001 brc 15,2d0ec6
>00000000002d0ec8: a517fffe nill %r1,65534
00000000002d0ecc: 40103000 sth %r1,0(%r3)
00000000002d0ed0: 07f0 bcr 15,%r0
00000000002d0ed2: e31020380004 lg %r1,56(%r2)
00000000002d0ed8: a7480000 lhi %r4,0
Call Trace:
([<000000000029c0fc>] virtnet_poll+0x290/0x3b8)
[<0000000000333fb8>] net_rx_action+0x9c/0x1b8
[<00000000001394bc>] __do_softirq+0x74/0x108
[<000000000010d16a>] do_softirq+0x92/0xac
[<0000000000139826>] irq_exit+0x72/0xc8
[<000000000010a7b6>] do_extint+0xe2/0x104
[<0000000000110508>] ext_no_vtime+0x16/0x1a
Last Breaking-Event-Address:
[<00000000002d0ec4>] vring_enable_cb+0x18/0x60
I looked into the virtio_net code for some time and I think the following
scenario happened. Please look at virtnet_poll:
[...]
/* Out of packets? */
if (received < budget) {
netif_rx_complete(vi->dev, napi);
if (unlikely(!vi->rvq->vq_ops->enable_cb(vi->rvq))
&& napi_schedule_prep(napi)) {
vi->rvq->vq_ops->disable_cb(vi->rvq);
__netif_rx_schedule(vi->dev, napi);
goto again;
}
}
If an interrupt arrives after netif_rx_complete, a second poll routine can run
on a different cpu. The second check for napi_schedule_prep would prevent any
harm in the network stack, but we have called enable_cb possibly after the
disable_cb in skb_recv_done.
static void skb_recv_done(struct virtqueue *rvq)
{
struct virtnet_info *vi = rvq->vdev->priv;
/* Schedule NAPI, Suppress further interrupts if successful. */
if (netif_rx_schedule_prep(vi->dev, &vi->napi)) {
rvq->vq_ops->disable_cb(rvq);
__netif_rx_schedule(vi->dev, &vi->napi);
}
}
That means that the second poll routine runs with interrupts enabled, which is
ok, since we can handle additional interrupts. The problem is now that the
second poll routine might also call enable_cb, triggering the BUG.
The only solution I can come up with, is to remove the BUG statement in
enable_cb - similar to disable_cb. Opinions or better ideas where the oops
could come from?
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Note that by itself, having a "hardware" random generator does very
little: you should probably run "rngd" in your guest to feed this into
the kernel entropy pool.
Included:
virtio_rng: dont use vmalloced addresses for virtio
If virtio_rng is build as a module, random_data is an address
in vmalloc space. As virtio expects guest real addresses, this
can cause any kind of funny behaviour, so lets allocate
random_data dynamically with kmalloc.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Hello Rusty,
sometimes it is useful to share a disk (e.g. usr). To avoid file system
corruption, the disk should be mounted read-only in that case. This patch
adds a new feature flag, that allows the host to specify, if the disk should
be considered read-only.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Anthony Liguori points out that three different transports use the virtio code,
but each one keeps its own counter to set the virtio_device's index field. In
theory (though not in current practice) this means that names could be
duplicated, and that risk grows as more transports are created.
So we move the selection of the unique virtio_device.index into the common code
in virtio.c, which has the side-benefit of removing duplicate code.
The only complexity is that lguest and S/390 use the index to uniquely identify
the device in case of catastrophic failure before register_virtio_device() is
called: now we use the offset within the descriptor page as a unique identifier
for the printks.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Lalancette <clalance@redhat.com>
Cc: Anthony Liguori <anthony@codemonkey.ws>
The common virtio code sets the bus_id, overriding anything virtio_pci
sets anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Lalancette <clalance@redhat.com>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Chris Lalancette <clalance@redhat.com> points out that virtio.c sets all device
names to '0', '1', etc, which looks silly in /proc/interrupts. We change this
from '%d' to 'virtio%d'.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Lalancette <clalance@redhat.com>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Fix a modprobe virtio_blk ; rmmod virtio_blk ; modprobe virtio_blk crash; this
was basically because we weren't doing "del_gendisk()" in the remove path.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (moved del_gendisk up)
Thanks to Jon Corbet & LWN. Only took me a day to join the dots.
Host->Guest netcat before (with unnecessily large receive buffers):
1073741824 bytes (1.1 GB) copied, 24.7528 seconds, 43.4 MB/s
After:
1073741824 bytes (1.1 GB) copied, 17.6369 seconds, 60.9 MB/s
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
Revert "USB: EHCI: fix performance regression"
USB: fsl_usb2_udc: fix recursive lock
USB: usb-serial: option: Don't match Huawei driver CD images
USB: pl2303: another product ID
USB: add another scanner quirk
USB: Add support for ROKR W5 in unusual_devs.h
USB: Fix M600i unusual_devs entry
USB: usb-storage: unusual_devs update for Cypress ATACB
USB: EHCI: fix performance regression
USB: EHCI: fix bug in Iso scheduling
USB: EHCI: fix remote-wakeup regression
USB: EHCI: suppress unwanted error messages
USB: EHCI: fix up root-hub TT mess
USB: add all configs to the "descriptors" attribute
USB: fix possible deadlock involving sysfs attributes
USB: Firmware loader driver for USB Apple iSight camera
USB: FTDI_SIO : Add support for Matrix Orbital PID Range
Create the dev_set_name function now so that various subsystems can
start changing over to it before other changes in 2.6.27 will make it
compulsory.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit fa38dfcc56.
It wasn't really a regression and David and Alan are still working
through the issues reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the interface info matching to all Huawei cards, as they all also
contain a Mass Storage Device interface (usually containing Windows
drivers) which should not get bound by this driver.
See also drivers/usb/storage/unusual_devs.h
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've just got a USB GPRS/EDGE modem branded Manufacturer Micromax Model
MMX610U (see http://www.airtel.in/level2_t3data.aspx?path=1/106/179)
working by adding another product ID to pl2303. Modem info reports same
module as Max Arnold's i.e.SIMCOM SIM600 but with product ID 0x0612
(cf Ox0611).
From: Steve Murphy <steve@gnusis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like the HP53{00,70} scanner other devices of the OEM Avision require
the USB_QUIRK_STRING_FETCH_255 to correct set a configuration with
"recent" Linux kernels.
Signed-off-by: René Rebe <rene@exactcode.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for rev 2 of an existing unusual_devs entry
enabling ROKR W5s to work. Greg, please apply.
From: Javier Smaldone <javier@smaldone.com.ar>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It turns out that the unusual_devs entry for the Motorola M600i needs
another flag. This patch adds it. Thanks to Atte André Jensen
<atte@ballbreaker.dk>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1101) updates the unusual_devs entry for the Cypress
ATACB pass-through. The protocol field is changed from US_PR_BULK to
US_PR_DEVICE, since the Cypress devices already set bInterfaceProtocol
to Bulk-only.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1099) fixes a performance regression in ehci-hcd. The
fundamental problem is that queue headers get removed from the
schedule too quickly, since the code checks for a counter advancing
rather than making an actual time-based check. The latency involved
in removing the queue header and then relinking it can severely
degrade certain kinds of workloads.
The patch replaces a simple counter with a timestamp derived from the
controller's uframe value. In addition, the delay for unlinking an
idle queue header is increased from 5 ms to 10 ms; since some
controllers (nVidia) have a latency of up to 1 ms for unlinking, this
reduces the relative impact from 20% to 10%.
Finally, a logical error left over from the IAA watchdog-timer
conversion is corrected. Now the driver will always either unlink an
idle queue header or set up a timer to unlink it later. The old code
would sometimes fail to do either.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Leonid <leonidv11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1098) changes the way ehci-hcd schedules its periodic
Iso transfers. That the current scheduling code is wrong is clear on
the face of it: Sometimes it returns -EL2NSYNC (meaning that an URB
couldn't be scheduled because it was submitted too late), but it does
this even when the URB_ISO_ASAP flag is set (meaning the URB should be
scheduled as soon as possible).
The new code properly implements as-soon-as-possible scheduling,
assigning the next unexpired slot as the URB's starting point. It
also is more careful about checking for Iso URB completion: It doesn't
bother to check for activity during frames that are already over,
and it allows for the possibility that some of the URB's packets may
have raced the hardware when they were submitted and so never got used
(the packet status is set to -EXDEV).
This fixes problems several people have experienced with USB video
applications.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1097) fixes a bug in the remote-wakeup handling in
ehci-hcd. The driver currently does not keep track of whether the
change-suspend feature is enabled for each port; the feature is
automatically reset the first time it is read. But recent changes to
the hub driver require that the feature be read at least twice in
order to work properly.
A bit-vector is added for storing the change-suspend feature values.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller. But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.
The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller. If it has, the
error message is suppressed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1095) cleans up the HCD glue and several of the EHCI
bus-glue files. The ehci->is_tdi_rh_tt flag is redundant, since it
means the same thing as the hcd->has_tt flag, so it is removed and the
other flag used in its place.
Some of the bus-glue files didn't get the relinquish_port method added
to their hc_driver structures. Although that routine currently
doesn't do anything for controllers with an integrated TT, in the
future it might. So the patch adds it where it is missing.
Lastly, some of the bus-glue files have erroneous entries for their
hc_driver's suspend and resume methods. These method pointers are
specific to PCI and shouldn't be used otherwise.
(The patch also includes an invisible whitespace fix.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
This patch (as1094) changes the output of the "descriptors" binary
attribute. Now it will contain the device descriptor followed by all
the configuration descriptors, not just the descriptor for the current
config.
Userspace libraries want to have access to the kernel's cached
descriptor information, so they can learn about device characteristics
without having to wake up suspended devices. So far the only user of
this attribute is the new libusb-1.0 library; thus changing its
contents shouldn't cause any problems.
This should be considered for 2.6.26, if for no other reason than to
minimize the range of releases in which the attribute contains only the
current config descriptor.
Also, it doesn't hurt that the patch removes the device locking --
which was formerly needed in order to know for certain which config was
indeed current.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a potential deadlock when the usb_generic driver is unbound
from a device. The problem is that generic_disconnect() is called
with the device lock held, and it removes a bunch of device attributes
from sysfs. If a user task happens to be running an attribute method
at the time, the removal will block until the method returns. But at
least one of the attribute methods (the store routine for power/level)
needs to acquire the device lock!
This patch (as1093) eliminates the deadlock by moving the calls to
create and remove the sysfs attributes from the usb_generic driver
into usb_new_device() and usb_disconnect(), where they can be invoked
without holding the device lock.
Besides, the other sysfs attributes are created when the device is
registered and removed when the device is unregistered. So it seems
only fitting for the extra attributes to be created and removed at the
same time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Uninitialised Apple iSight drivers present with a distinctive USB ID.
Once firmware has been uploaded, they disconnect and reconnect with a
new ID. At this point they can be driven by the uvcvideo driver. As this
is unique to the Apple cameras and not functionality shared by any other
UVC devices, it makes sense to provide the firmware loading
functionality in a separate driver. This driver will read an isight.fw
file extracted from the Apple driver using the tools at
http://bersace03.free.fr/ift/ and upload it to the camera. It will also
handle the case where the device loses its firmware during hibernation
and must have it reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.
A small number of units have been shipped early 2008
with a faulty USB Descriptor. Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: R. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/cpufreq/cpufreq.c the function cpufreq_add_dev() takes the
error exit 'err_out_unregister' from different places once with the
'cpu_policy_rwsem' lock held, once with the lock released:
| if (ret)
| goto err_out_unregister;
| }
|
| policy->governor = NULL; /* to assure that the starting sequence is
| * run in cpufreq_set_policy */
|
| /* set default policy */
| ret = __cpufreq_set_policy(policy, &new_policy);
| policy->user_policy.policy = policy->policy;
| policy->user_policy.governor = policy->governor;
|
| unlock_policy_rwsem_write(cpu);
|
| if (ret) {
| dprintk("setting policy failed\n");
| goto err_out_unregister;
| }
This leads to the following error message in case of a failing
__cpufreq_set_policy() call:
=====================================
[ BUG: bad unlock balance detected! ]
-------------------------------------
swapper/1 is trying to release lock (&per_cpu(cpu_policy_rwsem, cpu)) at:
[<c01b4564>] unlock_policy_rwsem_write+0x30/0x40
but there are no more locks to release!
other info that might help us debug this:
1 lock held by swapper/1:
#0: (sysdev_drivers_lock){--..}, at: [<c018fd18>] sysdev_driver_register+0x74/0x130
stack backtrace:
[<c002f588>] (dump_stack+0x0/0x14) from [<c00692fc>] (print_unlock_inbalance_bug+0xc8/0x104)
[<c0069234>] (print_unlock_inbalance_bug+0x0/0x104) from [<c006b7ac>] (lock_release_non_nested+0xc4/0x19c)
r6:00000028 r5:c3c1ab80 r4:c01b4564
[<c006b6e8>] (lock_release_non_nested+0x0/0x19c) from [<c006b9e0>] (lock_release+0x15c/0x18c)
r8:60000013 r7:00000001 r6:c01b4564 r5:c0541bb4 r4:c3c1ab80
[<c006b884>] (lock_release+0x0/0x18c) from [<c0061ba0>] (up_write+0x24/0x30)
r8:c0541b80 r7:00000000 r6:ffffffea r5:c3c34828 r4:c0541b8c
[<c0061b7c>] (up_write+0x0/0x30) from [<c01b4564>] (unlock_policy_rwsem_write+0x30/0x40)
r4:c3c34884
[<c01b4534>] (unlock_policy_rwsem_write+0x0/0x40) from [<c01b4c40>] (cpufreq_add_dev+0x324/0x398)
[<c01b491c>] (cpufreq_add_dev+0x0/0x398) from [<c018fd64>] (sysdev_driver_register+0xc0/0x130)
[<c018fca4>] (sysdev_driver_register+0x0/0x130) from [<c01b3574>] (cpufreq_register_driver+0xbc/0x174)
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Range check for power_output were missing.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a case that a wrong maximal rate is selected when
searching for better configurations.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When exiting from stay in table state (e.g. timer expiration),
all the statistics are reset and the RS flow should not continue
but only after enough statistics are collected again.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the rndis_wlan driver to connect to TKIP PSK
networks. It uses the ASSOCIATION_INFORMATION RNDIS call to pull back
the IEs and sends them back to userspace using wireless events. Tested
on a few wireless networks I have access to. Based on the similar
code in ndiswrapper.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
[edit: cleanups]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib_beacondone() is called from interrupt context,
this means we cannot use the mac80211 interface iterator
that uses the rtnl lock (since that uses a mutex which can sleep).
Instead we should use the atomic mac80211 interface iterator.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the antenna configuration has changed we should reset
the antenna RSSI value. Otherwise the value will be influenced
by the previous configuration quality which in turn will affect
the antenna diversity.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link quality estimation became quite low for all rt2x00 drivers
because the number of retries it took to send the frame were
counted as failure.
This does not correspond to the legacy driver link quality calculation,
by not counting it we will send somewhat more optimistic values to
mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the tx() handler runs while the device has disapeared,
we did return NETDEV_TX_OK but didn't free the skb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a kernel crash on rmmod, in the case where the controller
was restarted before doing the rmmod.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This updates the beacon template code to upload both templates,
if we never uploaded one before.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The grf5101 RF code needs to invoke grf5101_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The max2820 RF code needs to invoke max2820_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sa2400 RF code needs to invoke sa2400_write_phy_antenna every time the
channel is being switch.
This should be done passing the channel number to that function.
Incorrectly we were passing the same value that is written on the
channel RF register.
This may cause problems when operating on ch 14.
This patch fixes it.
Thanks to Alessandro Di Marco who found this issue!
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The static function max2820_rf_set_channel is called with conf == NULL
within its compilation unit. Originally this defaulted to b/g channel
1, but "cfg80211 API for channels/bitrates, mac80211 and driver
conversion" (commit 8318d78a44) mistakenly
dropped this check. This patch minimally restores the expected
behavior.
Reported-by: Colin Lai <colin_sh@163.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. Set input bits for direct keys codes
2. Set input bits for rotary encoder codes only if rotary
encoder is enabled
3. Enable EV_REL only if rotary encoder is enabled and rel_codes
are set up
Signed-off-by: Antonio Ospite <ao2@openezx.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Whenever CONFIG_DEBUG_RODATA is set in the kernel config many kernel
text sections become read-only, and the use of software breakpoints in
the kgdb tests will cause the kernel to fail to complete the start up.
Until such time that there is an official API for modifying read-only
text sections hardware breakpoints must be used to run the do_fork or
sys_open tests or the tests get skipped.
Also fix the duplicated include reported by:
Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
pciehp: add message about pciehp_slot_with_bus option
pci hotplug core: add check of duplicate slot name
pciehp: move msleep after power off
pciehp: poll cmd completion if hotplug interrupt is disabled
pciehp: fix slow probing
pciehp: fix NULL dereference in interrupt handler
shpchp: add message about shpchp_slot_with_bus option
PCI: don't enable ASPM on devices with mixed PCIe/PCI functions
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The pciehp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the following errors reported by Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
kobject_add_internal failed for 2 with -EEXIST, don't try to register things with the same name in the same directory.
Pid: 1, comm: swapper Tainted: G W 2.6.26-rc3 #1
[<c0266980>] kobject_add_internal+0x140/0x190
[<c0266afd>] kobject_init_and_add+0x2d/0x40
[<c027bc91>] pci_hp_register+0x81/0x2f0
[<c027fd07>] pciehp_probe+0x1a7/0x470
[<c01b3b84>] sysfs_add_one+0x44/0xa0
[<c01b3c1f>] sysfs_addrm_start+0x3f/0xb0
[<c01b497a>] sysfs_create_link+0x8a/0xf0
[<c0279570>] pcie_port_probe_service+0x50/0x80
[<c02e0545>] driver_sysfs_add+0x55/0x70
[<c02e0662>] driver_probe_device+0x82/0x180
[<c02e07cc>] __driver_attach+0x6c/0x70
[<c02dfe0a>] bus_for_each_dev+0x3a/0x60
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e04e6>] driver_attach+0x16/0x20
[<c02e0760>] __driver_attach+0x0/0x70
[<c02e0341>] bus_add_driver+0x1a1/0x220
[<c05db2d0>] pcied_init+0x0/0x80
[<c02e09cd>] driver_register+0x4d/0x120
[<c05db050>] ibm_acpiphp_init+0x0/0x190
[<c0125aab>] printk+0x1b/0x20
[<c05db2d0>] pcied_init+0x0/0x80
[<c05db2de>] pcied_init+0xe/0x80
[<c05c751a>] kernel_init+0x10a/0x300
[<c0120138>] schedule_tail+0x18/0x50
[<c0103b9a>] ret_from_fork+0x6/0x1c
[<c05c7410>] kernel_init+0x0/0x300
[<c05c7410>] kernel_init+0x0/0x300
[<c010485b>] kernel_thread_helper+0x7/0x1c
=======================
pci_hotplug: Unable to register kobject '2'<3>pciehp: pci_hp_register failed with error -22
Slot with the same name can be registered multiple times if shpchp or
pciehp driver is loaded after acpiphp is loaded because ACPI based
hotplug driver and Native OS hotplug driver trying to handle the same
physical slot. In this case, current pci_hotplug core will call
kobject_init_and_add() muliple time with the same name. This is the
cause of this problem. To fix this problem, this patch adds the check
into pci_hp_register() to see if the slot with the same name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
According to the PCI Express specification, we must wait for at least
1 second after turning power off before taking any action that relies
on power having been removed from the slot/adapter. For this, current
pciehp wait for 1 second after issuing the power off command in
hpc_power_off_slot() function. But waiting for 1 second in
hpc_power_off_slot() can make pciehp probing slow-down because pciehp
probe code calls hpc_power_off_slot() if the slot is not occupied just
in case. We don't need to wait for 1 second at the pciehp probe time
because there is no action on that empty slot. So move 1 second wait
from hpc_power_off_slot() to the caller of hpc_power_off_slot().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix improper long wait for command completion in pciehp probing.
As described in PCI Express specification, software notification is
not generated if the command that occurs as a result of a write to the
Slot Control register that disables software notification of command
completed events. Since pciehp driver doesn't take it into account,
such command is issued in pciehp probing, and it causes improper long
wait for command completion.
This patch changes the pciehp driver to take such command into
account.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix the "pciehp probing slow" problem reported from Jan C. Nordholz in
http://bugzilla.kernel.org/show_bug.cgi?id=10751.
The command completed bit in Slot Status register applies only to
commands issued to control the attention indicator, power indicator,
power controller, or electromechanical interlock. However, writes to
other parts of the Slot Control register would end up writing to the
control fields. Hence, any write to Slot Control register is
considered as a command. However, if the controller doesn't support
any of attention indicator, power indicator, power controller and
electromechanical interlock, command completed bit would not set in
writing to Slot Control register. In this case, we should not wait for
command completed bit set, otherwise all commands would be considered
not completed in timeout seconds (1 sec.).
The cause of the problem is pciehp driver didn't take this situation
into account. This patch changes pciehp to take it into account. This
patch also add the check for "No Command Completed Support" bit in
Slot Capability register. If it is set, we should not wait for command
completed bit set as well.
This problem seems to be revealed by the commit
c27fb883df that fixed the bug that
pciehp did not wait for command completed properly (pciehp just
ignored the command completion event).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some (broken?) platform assign the same slot name to multiple hotplug
slots. On such system, slot initialization would fail because of name
collision. The shpchp driver already have a "slot_with_bus" module
option which adds the bus number into the slot name. This patch adds
the message about this module option that will be displayed when slot
name collision is detected.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some versions of the Virtual I/O Server on Power
return 0x99 in the non-SCSI error status field as success,
rather than 0. This fixes the ibmvscsi driver to treat this
response as success.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following a hard reset of a SAS raid, one of the raid targets is occasionally
missing. I tracked this down to a pretty obscure little bug.
The LSI fusion drivers for SAS and Fibre Channel both use their respective
transport layers. Those transport layers increment the target number
assigned to new targets.
The routine __scsi_scan_target uses the "this_id" element of the Scsi_Host
structure to avoid scanning the scsi host adapter. Both fusion drivers set
"this_id" from a value returned in a firmware PortFacts response. For my
particular test case (SAS) the firmware id assigned to the initiator was
173. After enough raid resets to cause the raid targets to go and come a
sufficient number of times, the id assigned by the transport to a raid
target would match the id assigned by the host adapter to the "this_id"
field, resulting in that target not being scanned.
Fix by not assigning this_id and not checking it in slave_configure.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a reason why using C99 initialisers even in the supposedly
trivial structs is a good idea.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The chip phy_init() function must be called before the dig_enable() function
but dig_enable() is called when the device is opened and we only call
phy_init() after having reigstered the device, meaning the two can race.
Fix this by doing the phy_init() before we register the input device.
Thanks to Rodolfo Giometti <giometti@enneenne.com> for the report.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix driver name - thanks to Guennadi Liakhovetski <g.liakhovetski@gmx.de> for
reporting this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
phys is displayed in diagnostic output like that from evbug so ensure
that it is set to something.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also do not fail i8042 entire initialization if enabling dritek extension
fails.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver supports a few features (RNR NAK, port active event, SRQ
resize) that were not reported in the device capability flags. This
patch fixes that.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
