This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Some of the information in kernel boot message is not reasonable.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3846
- use _rambase as the start of kernel image.
kernel is in the region [_rambase, _ramstart]
- count in pages in per-cpu-page list as available memory
- reserved memory now include: [0 - 4K] for bad pointer catching,
memory reserved for abnormaly 05000263, memory reserved by kernel itself.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
writes to I/DMEM_CONTROL must be followed by SSYNC
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- Add anomaly workaround for bfin_gpio_reset_spi0_ssel1
- Fix style
- Update copyright
- Remove BUG_ON checks for functions intended to be used only by arch
support. GPIO users should only access using the generic GPIO API
- Make all GPIO identifier unsigned int
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Don't oops_in_progress if single step is comming from the
kernel, which happens if a single step occurs after a exception cause.
This fixes up the remaining issues in the toolchain bug.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Make sure the SYSTEM reset completes before we issue the CORE reset
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
early serial init also utilizes the peripheral request api - however
at this point bfin_gpio_init didn't allocate memory for the labels.
So we always have two zombies (allocated pin functions without labels)
This happens before the initcalls - We now allocate memory statically.
Define MAX_RESOURCES individually for each cpu.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
if it does get re-added, it needs to be in the boards directory,
not common code ... or it needs a re-implementation
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Clean up dump_bfin_mem so that it will display
content from the kernel, as well as l1 instruction, when deferred
HW errors happen, print out the last frame info if it makes sense.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3719
When the CPLBs get a miss, we do:
- find a victim in the HW table
- remove the victim
- find the replacement in the software table
- put it into the HW table.
If we can't find a replacement in the software table, we accidently
leave a duplicate in the HW table. This patch ensures that duplicate
is marked as not valid.
What we should do is find the replacement in the software table, before
we find a victim in the HW table - but its too late in the release cycle
to do that much restructuring of this code.
Rather that duplicate code, connect Hardware Errors (irq5) into trap_c,
so user space processes get killed properly.
The rest of irq_panic() can be moved into traps.c (later)
There is still a small corner case that causes problems when a
pheriperal interrupt goes off a single cycle before a user space
hardware error. This causes a kernel panic, rather than the user
space process being killed.
But, this checkin makes things work in 99.9% of the cases, and is a vast
improvement from what is there today (which fails 100% of the time).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
We need to send signals with the proper PC, or gdb gets
confused, and lots of tests fail. This should fix that.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- remove duplicated defines for the BF561
- generalize L2 support (so that it works for BF54x) and mark it executable
- add support for reading/executing the Boot ROM sections
(since it has data/functions we may need at runtime)
- and fixup names for each map
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- no need to declare their sizes in the common header
- no need to tack on the section attribute as only the definition matters, not references
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Revert this patch:
move the init sections to the end of memory, so that after they
are free, run time memory is all continugous - this should help decrease
memory fragementation. When doing this, we also pack some of the other
sections a little closer together, to make sure we don't waste memory.
To make this happen, we need to rename the .data.init_task section to
.init_task.data, so it doesn't get picked up by the linker script glob.
Since it causes the kernel not to boot up with mtd filesystems.
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
/*
* CPUs often take a performance hit when accessing unaligned memory
* locations. The actual performance hit varies, it can be small if the
* hardware handles it or large if we have to take an exception and fix
* it
* in software.
*
* Since an ethernet header is 14 bytes network drivers often end up
* with
* the IP header at an unaligned offset. The IP header can be aligned by
* shifting the start of the packet by 2 bytes. Drivers should do this
* with:
*
* skb_reserve(NET_IP_ALIGN);
*
* The downside to this alignment of the IP header is that the DMA is
* now
* unaligned. On some architectures the cost of an unaligned DMA is high
* and this cost outweighs the gains made by aligning the IP header.
*
* Since this trade off varies between architectures, we allow
* NET_IP_ALIGN
* to be overridden.
*/
This new function insl_16 allows to read form 32-bit IO and writes to
16-bit aligned memory. This is useful in above described scenario -
In particular with the AXIS AX88180 Gigabit Ethernet MAC.
Once the device is in 32-bit mode, reads from the RX FIFO always
decrements 4bytes.
While on the other side the destination address in SDRAM is always
16-bit aligned.
If we use skb_reserve(0) the receive buffer is 32-bit aligned but later
we hit a unaligned exception in the IP code.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
If you need a 64 bit divide in the kernel, use asm/div64.h.
Revert the addition of udivdi3.
Cc: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
The only user of get_wchan I was able to find is the proc fs - and proc
can't be built modular.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
The only user is the a.out support.
It was therefore removed prior to the blackfin merge from all
architectures not supporting a.out.
Currently, Blackfin doesn't suppport a.out.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
move the init sections to the end of memory, so that after they
are free, run time memory is all continugous - this should help decrease
memory fragementation. When doing this, we also pack some of the other
sections a little closer together, to make sure we don't waste memory.
To make this happen, we need to rename the .data.init_task section to
.init_task.data, so it doesn't get picked up by the linker script glob.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
We currently do not. Also make it easier to handle cplb violations - in traps.c
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This is fixes a problem where we could jump to the wrong address. By
doing a "p0 = reti; jump (p0)". If a different, higher level interrupt
came in, just before, rather than returning to the calling function, we
would return to a random place in the kernel.
This very elegant fix from Bernd grabs the return location off the
stack, and places it into P0, so when we do a return, it goes to the
correct place.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- move the CONFIG_KGDB into one block, for easier reading
- remove printk from printk_address, and pass around buffers. Also
print out the labels when decoding CPLB errors, so you know exactly
where the error was.
- Do not use fixed addresses, becuase people do not know where they come from.
- Turn the printing level down on the dump, so if you don't want,
only the signal prints out - just like on other archs. If a kernel/interrupt
crashes, it should dump everything all the time
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This fixes two things:
- stop calling write_lock_irq/write_unlock_irq which can turn modify
irq levels
- don't calling mmput when handing exceptions - since this might_sleep,
which does a rti, and leaves us in kernel space (irq15, rather
than irq5).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: use KBUILD_CFLAGS and KBUILD_AFLAGS in Makefile
Blackfin arch: Javier Herrer writes: fix building when icache and dcache is disabled
Sam Ravnborg