Implement pm object for the PCI Express port driver in order to use
the new power management framework and reduce the code size.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
With for (busnr = 0; busnr <= end; busnr++) { ... } busnr reaches end + 1
after the loop. So fix the "no busses available" check to look for just
busnr > end rather than >=.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
- Rename pci_osc_control_set() to acpi_pci_osc_control_set() according
to the other API names in drivers/acpi/pci_root.c.
- Move _OSC related definitions to include/linux/acpi.h because _OSC
related API is implemented in drivers/acpi/pci_root.c now.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Tested-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The cmd_busy field in struct controller takes only two values 0 or
1. So it should be one bit.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Current pciehp disables software notification of adapter presence
changed event and MRL changed event when slot is turned off. Because
of this, there is no way to detect those events on empty slots in the
current pciehp implementation.
According to the past discussion(*), this behavior was introduced to
prevent endless loop that could happen if pcie_isr() runs after power
fault is detected on a certain platform whose stickey power-fault bit
remains on till the slot is powered on again.
(*) http://sourceforge.net/mailarchive/message.php?msg_id=20051130135409.A14918%40unix-os.sc.intel.com
I think this endless loop can be avoided using one bit flag that
indicates power fault had been detected, instead of disabling software
notification of adapter present changed event and MRL changed event.
With this patch, we can enable software notification mechanism of
presence changed and MRL changed event on the empty slots again.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix possible endless loop in pcie_isr.
Currently, pcie_isr() (interrupt service routine of pciehp) can end up in an
endless loop if the Slot Status register is set again immediately after being
cleared. According to the past discussion (see below URL) this case can happen
if the power fault detected bit is set during handling.
http://sourceforge.net/mailarchive/message.php?msg_id=20051130135409.A14918%40unix-os.sc.intel.com
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Error handling code following a kmalloc should free the allocated data.
Since the subsequent code that could provoke an error does not use the
allocated data, the allocation is just moved below it.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing pieces here for the pci subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI Express port driver uses 'struct pcie_port_service_id' for
matching port service devices and drivers, but this structure
contains fields that duplicate information from the port device
itself (vendor, device, subvendor, subdevice) and fields that are not
used by any existing port service driver (class, class_mask,
drvier_data). Also, both existing port service drivers (AER and
PCIe HP) don't even use the vendor and device fields for device
matching. Therefore 'struct pcie_port_service_id' can be removed
altogether and the only useful members of it (port_type, service) can
be introduced directly into the port service device and port service
driver structures. That simplifies the code quite a bit and reduces
its size.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The second argument of the ->probe() callback in
struct pcie_port_service_driver is unnecessary and never used.
Remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The RPA PCI hotplug driver calls EEH routines, so should depend on
EEH. Also PPC_PSERIES implies PPC64, so remove that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Move the enabling of interrupts after all of the data structures
are setup so that we can safely run the interrupt handler as
soon as it is registered.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
Some hardware exposes PCIE slots in such a way that they can be claimed
by either the acpiphp or pciehp driver. pciehp is the preferred driver
if the firmware allows the OS to claim control via the _OSC method so
should be loaded first - if it fails to bind (either due to a missing
_OSC method or the firmware refusing to hand off control) then we can
fall back to acpiphp or a vendor-specific driver.
This patch simply changes the link order to ensure that pciehp will be
initialised before acpiphp if both are statically built into the kernel.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For PCI devices, pci_bus_assign_resources() must be called to set up the
pci_device->resource array before pci_bus_add_devices() can be called, else
attempts to load drivers results in BAR collision errors where there are none.
This is not done in fakephp, so devices can be "unplugged" but scanning the
parent bus won't bring the devices back due to resource unallocation. Move the
pci_bus_add_device-calling logic into pci_rescan_bus and preface it with a call
to pci_bus_assign_resources so that we only have to (re)allocate resources once
per bus where a new device is found.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: fix lock imbalance in pciehp
PCI PM: Restore standard config registers of all devices early
PCI/MSI: bugfix/utilize for msi_capability_init()
set_lock_status omits mutex_unlock in fail path. Add the omitted
unlock.
As a result a lockup caused by this can be triggered from userspace
by writing 1 to /sys/bus/pci/slots/.../lock often enough.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI hotplug panic with current git head
http://lkml.org/lkml/2009/1/10/136
Rather than reverting the entire commit that causes the crash:
e8c331e963
"PCI hotplug: introduce functions for ACPI slot detection"
simply harden against it while the changes to
the hotplug code on this particularl machine are understood.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
func is checked not to be NULL a few lines before.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@
if (x@p1 == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
x@p2 == NULL
|
x@p2 != NULL
)
// another path to the test that is not through p1?
@s exists@
local idexpression r.x;
position r.p1,r.p2;
@@
... when != x@p1
(
x@p2 == NULL
|
x@p2 != NULL
)
@fix depends on !s@
position r.p1,r.p2;
expression x,E;
statement S1,S2;
@@
(
- if ((x@p2 != NULL) || ...)
S1
|
- if ((x@p2 == NULL) && ...) S1
|
- BUG_ON(x@p2 == NULL);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up register definitions related to PCI Express Hot plug.
- Add register definitions into include/linux/pci_regs.h, and use
them instead of pciehp's locally definied register definitions.
- Remove pciehp's locally defined register definitions
- Remove unused register definitions in pciehp.
- Some minor cleanups.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bit 10 in Link Status register used to be defined as Training Error in
the PCI Express 1.0a specification. But it was removed by Training Error
ECN and is no longer defined. So pciehp must ignore the value read from
it.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some ACPI related PCI hotplug code can be shared among PCI hotplug
drivers. This patch introduces the following functions in
drivers/pci/hotplug/acpi_pcihp.c to share the code, and changes
acpiphp and pciehp to use them.
- int acpi_pci_detect_ejectable(struct pci_bus *pbus)
This checks if the specified PCI bus has ejectable slots.
- int acpi_pci_check_ejectable(struct pci_bus *pbus, acpi_handle handle)
This checks if the specified handle is ejectable ACPI PCI slot. The
'pbus' parameter is needed to check if 'handle' is PCI related ACPI
object.
This patch also introduces the following inline function in
include/linux/pci-acpi.h, which is useful to get ACPI handle of the
PCI bridge from struct pci_bus of the bridge's secondary bus.
- static inline acpi_handle acpi_pci_get_bridge_handle(struct pci_bus *pbus)
This returns ACPI handle of the PCI bridge which generates PCI bus
specified by 'pbus'.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI based hot-pluggable PCIe slot detection logic was added to
prevent the problem non hot-pluggable PCIe slot was detected as
hot-pluggable. The slot detection logic can be selected through
'pciehp_detect_mode', but it would be better if it is selected
automatically.
This patch adds 'auto' option for 'pciehp_detect_mode'. When it is
specified, pciehp judges which 'acpi' or 'pcie' should be used. It
seems that the physical slot number is duplicated among some slots on
most of the platforms with the above-mentioned problem. So 'auto' mode
uses this information to judge which 'acpi' or 'pcie' should be
used. That is, if duplicated physical slot numbers are detected,
'acpi' mode is used. This method is not perfect, but it's realistic.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a problem that some non hot-pluggable PCIe slots are detected
as hot-pluggable by pciehp on some platforms. The immediate cause of
this problem is that hot-plug capable bit in the Slot Capabilities
register is set even for non hot-pluggable slots on those platforms.
It seems a BIOS/hardware problem, but we need workaround about that.
Some of those platforms define hot-pluggable PCIe slots on ACPI
namespace properly, while hot-plug capable bit in the Slot
Capabilities register is set improperly. So using ACPI namespace
information in pciehp to detect PCIe hot-pluggable slots would be a
workaround.
This patch adds 'pciehp_detect_mode' module option. When 'acpi' is
specified, pciehp uses ACPI namespace information to detect PCIe
hot-pluggable slots.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch changes cpqphp to use interrupt pin values just as they
come from PCI config space, i.e., 1=INTA, ..., 4=INTD.
pcibios_set_irq_routing() takes pin arguments in the range 0=INTA, ...,
3=INTD, so we'll adjust the pin just before calling it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Clean up whitespace.
Setting 'let c_space_errors=1' in .vimrc shows all sorts of
ugliness. ;)
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
According to section 6.3.6 of the ACPI spec, the presence of an _RMV
method that evaluates to 1 is sufficient to indicate that a slot is
removable without needing an eject method. This patch refactors the
ejectable slot detection code a little in order to flag these slots as
ejectable and register them. Acpihp then binds to the expresscard slot
on my HP test machine.
Acked-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_get_slot does a pci_dev_get, so pci_dev_put needs to be called in an
error case.
An alterative would be to move the test_and_set_bit before the call to
pci_get_slot.
The problem was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
local idexpression *n;
statement S1,S2;
expression E,E1;
expression *ptr != NULL;
type T,T1;
@@
(
if (!(n = pci_get_slot(...))) S1
|
n = pci_get_slot(...)
)
<... when != pci_dev_put(n)
when != if (...) { <+... pci_dev_put(n) ...+> }
when != true !n || ...
when != n = (T)E
when != E = n
if (!n || ...) S2
...>
(
return \(0\|<+...n...+>\|ptr\);
|
+ pci_dev_put(n);
return ...;
|
pci_dev_put(n);
|
n = (T1)E1
|
E1 = n
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pciehp driver waits for 1000 msec after turning power off to make
sure the power has been completely removed. But this 1000 msec wait is
not needed if a slot doesn't implement power control because software
cannot control the power. Power will be automatically removed at adapter
removal time on such a slot
Tested-by: "Phil Endecott" <phil_pibbu_endecott@chezphil.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
External driver files should not include any private acpica headers.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: cleanup
Now that arch/x86/pci/pci.h is used in a number of other places as well,
move the lowlevel x86 pci definitions into the architecture include files.
(not to be confused with the existing arch/x86/include/asm/pci.h file,
which provides public details about x86 PCI)
Tested on: X86_32_UP, X86_32_SMP and X86_64_SMP
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
I happened to notice that the ibmphp hotplug driver does something
rather silly in its init routine. It purposely calls module_put so as
to underflow its module ref count to avoid being removed from the
kernel. This is bad practice, and wrong, since it provides a window for
subsequent module_gets to reset the refcount to zero, allowing an unload
to race in and cause all sorts of mysterious panics. If the module is
unsafe to load, simply omitting the module_exit parameter is sufficient
to prevent the kernel from allowing the unload.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Certain HP machines require the full 64 bits of _SUN as allowed
by the ACPI spec. Without this change, we get name collisions in
the lower 32 bits of the _SUN returned by firmware.
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Justin Chen <justin.chen@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch fixes the problem that causes an occupied slot to be turned
off even if it has a working device.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pseries PCI hotplug code has a number of issues, ranging from
incorrect resource setup to crashes, depending on what is added,
when, whether it contains a bridge, etc etc....
This fixes a whole bunch of these, while actually simplifying the code
a bit, using more generic code in the process and factoring out common
code between adding of a PHB, a slot or a device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix printk format warning:
drivers/pci/hotplug/acpiphp_ibm.c:207: warning: format '%08lx' expects type 'long unsigned int', but argument 3 has type 'long long unsigned int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch refines messages in shpchp module. The main changes are as
follows:
- remove the trailing "."
- remove __func__ as much as possible
- capitalize the first letter of messages
- show PCI device address including its domain
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch refines messages in pciehp module. The main changes are as
follows:
- remove the trailing "."
- remove __func__ as much as possible
- capitalize the first letter of messages
- show PCI device address including its domain
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The following patch fixes the regression in 2.6.27 that causes kernel
NULL pointer dereference at cpqphp driver probe time. This patch should
be backported to the .27 stable series.
Seems to have been introduced by
f46753c5e3.
The root cause of this problem seems that cpqphp driver calls
pci_hp_register() wrongly. In current implementation, cpqphp driver
passes 'ctrl->pci_dev->subordinate' as a second parameter for
pci_hp_register(). But because hotplug slots and it's hotplug controller
(exists as a pci funcion) are on the same bus, it should be
'ctrl->pci_dev->bus' instead.
Cc: <stable@kernel.org>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits)
dock: make dock driver not a module
ACPI: fix ia64 build warning
ACPI: hack around sysfs warning with link order
ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n
intel_menlo: fix build warning
panasonic-laptop: fix build
ACPICA: Update version to 20080926
ACPICA: Add support for zero-length buffer-to-string conversions
ACPICA: New: Validation for predefined ACPI methods/objects
ACPICA: Fix for implicit return compatibility
ACPICA: Fixed a couple memory leaks associated with "implicit return"
ACPICA: Optimize buffer allocation procedure
ACPICA: Fix possible memory leak, error exit path
ACPICA: Fix fault after mem allocation failure in AML parser
ACPICA: Remove unused ACPI register bit definition
ACPICA: Update version to 20080829
ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname
ACPICA: Cleanup for internal Reference Object
ACPICA: Update comments - no functional changes
ACPICA: Update for Reference ACPI_OPERAND_OBJECT
...
The pattern !E && !E->fld is nonsensical. The patch below updates this
according to the assumption that && should be ||. But perhaps another
solution was intended.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@disable and_comm@
expression E;
identifier fld;
@@
- !E && !E->fld
+ !E || !E->fld
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds polling mechanism for Data Link Layer Link Active bit
after turning power on, instead of waiting for 1000 msec. This reduces
reduce the unnecessary long wait.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI core now manages slot names on behalf of slot detection
and slot hotplug drivers, including the handling of duplicate
slot names.
We can use the fakephp driver to help test the new functionality.
Add a 'dup_slots' module param to force fakephp to create multiple
slots with the same name. We can then verify that the PCI core
correctly renamed the slots.
sapphire:/sys/bus/pci/slots # modprobe fakephp dup_slots
sapphire:/sys/bus/pci/slots # ls
fake fake-10 fake-3 fake-5 fake-7 fake-9
fake-1 fake-2 fake-4 fake-6 fake-8
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>