The VIDIOC_QUERYCTRL command needs to actually do a queryctrl, not a
querymenu. Similarly, the VIDIOC_QUERYMENU command needs to actually
do a querymenu not a queryctrl.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some em28xx devices use the PCM IN AC 97 PIN for digital audio. However,
currently, the PCM IN selection is not set by the driver. This patch allows
specifying the PCM IN expected output, via board description table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zoran driver does a module_get/put of THIS_MODULE on device open/close.
This isn't necessary as the kernel does this automatically.
Clean up the failure path of zoran_open() somewhat.
Make the dprintk()s on open/close a higher debug level and make the user
count printed take the current open/close into account.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver should only use the kernel mapped io address, zr36057_mem, and
not the PCI bus address, zr36057_adr. Since the latter is only printed out
once, there is no need to save it in the driver data structure.
There was some old code that looked like it was for the Alpha architecture
which would use the PCI bus address. It probably no longer applies to
modern kernels.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using custom code, just let the device layer look it up for us
from the pci device table. This requires extending the pci device table to
list each known card, plus a catch-all entry for the cards that don't have
sub-system vendor/device data.
Improve some of the info and error messages too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver was keeping a global array with an entry for each zoran device
probed. It was a leftover from when the driver didn't dynamically allocate
the driver data for each device.
There was only one use left, in the video device's ->open() method, looking
up the struct zoran for the opened device from the minor number. This can
be done better with video_get_drvdata().
Since zoran_num is now only used in the pci driver's ->probe() method, it
doesn't need to be an atomic_t and be static. There is a race if multiple
zoran cards could be probed at the same time, but currently the probe
method for a given driver is single threaded.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When initializing a module parameter that is a per-card array, use
"{ [0 ... (BUZ_MAX-1)] = -1 }" instead of "{ -1, -1, -1, -1 }". This way
all of the entries will be correctly set to -1 if someone changes BUZ_MAX
to a value other than 4.
Adjust some of the parameter help text too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When enabling a shared IRQ line, then saa7134_irq handler could be invoked
before the driver had completely set up internal structures, due to a shared
interrupt line firing. Clear the saa7134 interrupt status reg, before
requesting the irq line, so that stale IRQ status isn't processed before the
internal structures are set up.
Marcin Slusarz recently brought this Oops to the attention of the v4l-dvb
lists and provided an initial analysis by investigating reports found here:
http://kerneloops.org/guilty.php?guilty=mute_input_7133&version=2.6.27-release&start=1802240&end=1835007&class=oops
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Analog support for HVR-1250 has not been completed, but does exist for
the HVR-1800.
Since both cards use the same driver, it tries to create the analog
dev for both devices, which is not possible.
This causes a NULL error to show up in video_open and mpeg_open.
-Mark
Iterations through the cx23885_devlist must check for NULL
pointers as some supported devices only have DVB support at the moment.
Mark Jenks encoutered an Oops in a system with both an HVR-1250 and HVR-1800
installed.
-Andy
Reported-by: Mark Jenks <mjenks1968@gmail.com>
Tested-by: Mark Jenks <mjenks1968@gmail.com>
Signed-off-by: Mark Jenks <mjenks1968@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register 0x2d has to be set differently in the saa7129 compared to the
saa7127. This was not done correctly, so S-Video was broken in certain
circumstances.
This fixes a regression introduced in 2.6.28.
Signed-off-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a really old and crufty driver that wasn't using the long
established pci driver framework.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
[mchehab@redhat.com: Cleaned up a few CodingStyle issues]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If Hauppauge eeprom is corrupted, the driver returns tuner = 0, instead
of TUNER_ABSENT.
This makes the drivers to initialize tuner, instead of handling the
manual parameter.
Since the tuner core rejects that a tuner to have their type changed,
this breaks the manual tuner override.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 60b4bde48b removed an unused
struct on zoran driver, when compiled with "Y".
However, as pointed by Jean Delvare <khali@linux-fr.org>, this is
neeeded when the driver is compiled as a module, since udev relies on it
to auto-load the module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
to avoid:
| tvp514x 0-005c: No platform data
| !!<3>tvp514x 0-005d: No platform data
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap <randy.dunlap@oracle.com> wrote:
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c: In function 'cx88_call_i2c_clients':
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:122: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:123: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:127: error: 'struct cx88_core' has no member named 'gate_ctrl'
> linux-next-20090108/drivers/media/video/cx88/cx88-i2c.c:128: error: 'struct cx88_core' has no member named 'gate_ctrl'
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC specification release number is a binary-coded decimal number, print
it as such.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx were trying to access the third input entry, even for boards that
don't support it.
This patch reviews the input mux selection fixing this bug and a few
other troubles, like not validating the input on one userspace ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As Randy Dunlap <randy.dunlap@oracle.com> reported, cx88 has some compilation issues:
drivers/built-in.o: In function `cx88_call_i2c_clients':
(.text+0x20af17): undefined reference to `videobuf_dvb_get_frontend'
drivers/built-in.o: In function `cx8802_probe':
cx88-mpeg.c:(.devinit.text+0x268c4): undefined reference to `videobuf_dvb_alloc_frontend'
cx88-mpeg.c:(.devinit.text+0x268ea): undefined reference to `videobuf_dvb_dealloc_frontends'
With those configs:
CONFIG_VIDEO_CX88=y
CONFIG_VIDEO_CX88_BLACKBIRD=y
CONFIG_VIDEO_CX88_DVB=m
CONFIG_DVB_CORE=m
After carefully examining the code, with the current code, several cx88 drivers
(cx8800, cx8802, cx88_dvb and cx88_blackbird) should be compiled as a module,
if one of them is marked as such. Just fixing Kconfig could create a very complex
set of rules. Also, this hides a problem with the current approach where the dvb
functionality weren't confined inside dvb module.
What happens is that:
- cx88-i2c (part of cx8800) has some special rules if DVB;
- cx88-mpeg (cx8802 module) has also part of DVB init code;
- cx88-dvb has the rest of the dvb code;
- cx88-blackbird can be used with cx88-mpeg, having cx88-dvb or not.
So, instead of doing some tricks at Kconfig and wait for a next breakage,
this patch moves the dvb code inside cx88-i2c and cx88-mpeg into cx88-dvb.
Another problem is that cx8802 were being compiled, even without cx88-dvb
and cx88-blackbird modules.
While on this code, let's fix also a reported problem:
http://www.linuxtv.org/pipermail/linux-dvb/2009-January/031225.html
A solution for the issue were proposed here:
http://www.mail-archive.com/linux-media@vger.kernel.org/msg00021.html
Thanks to Randy, Andy, Gregoire and Thomas for helping us to detect
and solve the issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
anysee.c:44:5: warning: symbol 'dvb_usb_anysee_delsys' was not declared. Should it be static?
cx24116.c:378:3: warning: symbol 'CX24116_MODFEC_MODES' was not declared. Should it be static?
stb0899_algo.c:57:5: warning: symbol 'stb0899_get_srate' was not declared. Should it be static?
stb0899_algo.c:766:6: warning: symbol 'Log2Int' was not declared. Should it be static?
stb0899_drv.c:137:20: warning: symbol 'stb0899_quant_tab' was not declared. Should it be static?
stb0899_drv.c:180:20: warning: symbol 'stb0899_est_tab' was not declared. Should it be static?
stb0899_drv.c:220:5: warning: symbol '_stb0899_read_reg' was not declared. Should it be static?
budget-ci.c:1348:23: warning: symbol 'tt3200_stb6100_config' was not declared. Should it be static?
/home/v4l/master/v4l/cx25840-core.c:190:6: warning: symbol 'cx25840_work_handler' was not declared. Should it be static?
/home/v4l/master/v4l/m5602_s5k83a.c:116:6: warning: symbol 's5k83a_dump_registers' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/master/v4l/em28xx-core.c:396:25: warning: symbol 'outputs' was not declared. Should it be static?
/home/v4l/master/v4l/em28xx-input.c:324:6: warning: symbol 'em28xx_ir_start' was not declared. Should it be static?
/home/v4l/master/v4l/em28xx-cards.c:1925:5: warning: symbol 'em28xx_init_dev' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. now pxa_camera.c uses ioremap() for register access, pxa_camera.h is
totally useless. Remove it.
2. <asm/dma.h> does no longer include <mach/dma.h>, include the latter
file explicitly
delete mode 100644 drivers/media/video/pxa_camera.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not all architectures provide clear_user_page(), but clear_user_highpage()
is available everywhere at least via the compatibility inline function.
Is this the "trivial patch" that's required for these two drivers?
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
This patch (as1161) changes the interface to
usb_lock_device_for_reset(). The existing interface is apparently not
very clear, judging from the fact that several of its callers don't
use it correctly. The new interface always returns 0 for success and
it always requires the caller to unlock the device afterward.
The new routine will not return immediately if it is called while the
driver's probe method is running. Instead it will wait until the
probe is over and the device has been unlocked. This shouldn't cause
any problems; I don't know of any cases where drivers call
usb_lock_device_for_reset() during probe.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a number of drivers which set their i2c bus class to
I2C_CLASS_CAM_DIGITAL, however no chip driver actually checks for this
flag, so we might as well drop it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
f_op->poll is the only vfs operation which is not allowed to sleep. It's
because poll and select implementation used task state to synchronize
against wake ups, which doesn't have to be the case anymore as wait/wake
interface can now use custom wake up functions. The non-sleep restriction
can be a bit tricky because ->poll is not called from an atomic context
and the result of accidentally sleeping in ->poll only shows up as
temporary busy looping when the timing is right or rather wrong.
This patch converts poll/select to use custom wake up function and use
separate triggered variable to synchronize against wake up events. The
only added overhead is an extra function call during wake up and
negligible.
This patch removes the one non-sleep exception from vfs locking rules and
is beneficial to userland filesystem implementations like FUSE, 9p or
peculiar fs like spufs as it's very difficult for those to implement
non-sleeping poll method.
While at it, make the following cosmetic changes to make poll.h and
select.c checkpatch friendly.
* s/type * symbol/type *symbol/ : three places in poll.h
* remove blank line before EXPORT_SYMBOL() : two places in select.c
Oleg: spotted missing barrier in poll_schedule_timeout()
Davide: spotted missing write barrier in pollwake()
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Brad Boyer <flar@allandria.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roland McGrath <roland@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The radio_release function of the BTTV driver is missing a call to
v4l2_prio_close. As a result, after the radio device has been opened at
least once (e.g., by HAL during bootup), v4l2_priority will never drop below
V4L2_PRIORITY_INTERACTIVE again. With the following patch against 2.6.28,
applications that run with V4L2_PRIORITY_BACKGROUND are able to open devices
again. Previous Linux versions are affected as well.
Signed-off-by: Udo Steinberg <udo@hypervisor.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code had calls to both usb_set_intfdata and dev_set_drvdata, doing the
same thing.
The semantic patch that lead to finding this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@header@
@@
@same depends on header@
position p;
@@
usb_set_intfdata@p(...) { ... }
@depends on header@
position _p!=same.p;
identifier _f;
struct usb_interface *intf;
expression data;
@@
_f@_p(...) { <+...
- dev_set_drvdata(&intf->dev, data);
+ usb_set_intfdata(intf, data);
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices require different setups on struct_audio. Due to that, we
may need to change some fields at dev.adev during device probe. So, this
patch moves the dynamic memory allocation of adev at em28xx-alsa to the
dynamic allocation of struct em28xx dev that happens during device
probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes autodetection for Avermedia AVerTV GO 007 FM Plus (M15C)
(PCI ID 1461:f31d).
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Avermedia AVer TV GO 007 FM Plus (M15C) on
saa7134 driver (PCI ID 1461:f31d).
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the i2c driver ID will be removed in the near future we have to
modify the v4l2 debugging API to use the driver name instead of driver ID.
Note that this API is not used in applications other than v4l2-dbg.cpp
as it is for debugging and testing only.
Should anyone use the old VIDIOC_G_CHIP_IDENT, then this will be logged
with a warning that it is deprecated and will be removed in 2.6.30.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This rename prevents conflicts with the older compat_ioctl32 module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since internal to v4l2 the ioctl prototype is the same regardless of it
being called through .ioctl or .unlocked_ioctl, we need to convert it all
to the long return type of unlocked_ioctl.
Thanks to Jean-Francois Moine for posting an initial patch for this and
thus bringing it to our attention.
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil