This patch actually replaces the 'struct pad_desc' with a u64 cookie
to facilitate adding platform specific pad_ctrl settings to an
existing pad definition.
So, instead of:
iomux_v3_cfg_t power_key = MX51_PAD_EIM_A27__GPIO_2_21;
power_key.pad_ctrl = MX51_GPIO_PAD_CTRL_2;
mxc_iomux_v3_setup_pad(&power_key);
one can write:
mxc_iomux_v3_setup_pad((MX51_PAD_EIM_A27__GPIO_2_21 & ~MUX_PAD_CTRL_MASK) | MX51_GPIO_PAD_CTRL_2);
Patch applies to branch 'imx-for-2.6.38' of git://git.pengutronix.de/git/imx/linux-2.6
Signed-Off-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for FIQ on mx51 TZIC
TZIC changes tested with FIQ audio on an mx51 board
AVIC changes build with mx3_defconfig, not tested
Signed-off-by: Peter Horton <phorton@bitbox.co.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MX51 has two watchdog modules.
Add support for both of them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, to define a GPIO number, we're using something like :
#define EFIKAMX_PCBID0 (2*32 + 16)
to define GPIO 3 16.
This is not really readable and it's error prone imho (note the 3 vs 2).
So, I'm introducing a new macro to define this in a better way. Now, the
code sample become :
#define EFIKAMX_PCBID0 IMX_GPIO_NR(3, 16)
v2:
- move to gpio.h
- add parens & spaces
- switch to IMX_GPIO_NR instead of MX51_GPIO_NR
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In commit 2c20b9f (ARM: mx25: dynamically allocate mxc-ehci devices) I
changed the offset to the value specified in the reference manual
intending to test this change on hardware. This slipped through and now
prooved to be wrong. So fix it and add a comment about the
documentation being wrong.
Reported-by: Jaume Ribot <jaume@fqingenieria.es>
Cc: Michael Trimarchi <trimarchi@gandalf.sssup.it>
Cc: Shawn Guo <shawn.gsc@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The SDMA firmware consists of a ROM part and a RAM part.
The ROM part is always present in the SDMA engine and
is sufficient for many cases.
This patch allows to pass in platform data containing
the script addresses in ROM, so loading a firmware is
optional now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Instead of reading the silicon version from ROM, we should
read the SREV register from the IIM.
Freescale has dropped all support for MX51 REV1.0, only MX51
REV 2.0 and 3.0 are valid.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efikamx board is using a gpio to reset the board so add support
for it
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- add definition to configure pads as ESDHC{1,2} WP and CD
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- ALT0 is used to set GPIO mode of GPIO_1_{2,3,4,5,6,7,8,9} but it's ALT1
for GPIO_1_{0,1}.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The following patch is a first step to convert the 'struct pad_desc'
to a bitmapped cookie to facilitate adding platform specific pullup or
drive strength definitions to existing pad definitions without need to
rewrite the complete pad def.
The patch wraps 'struct pad_desc' in an opaque data type and
introduces macros to access the individual members.
This patch does not constitute any functional change!
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While adapting the #defines for this I noticed that the offset
used for USB HS on i.MX35 differs from the documented offset.
I kept the working offset and commented that the documentation
differs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Compared to the static devices the dynamic have a DMA resource.
This should be save as it seems unused in the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The mxc-keypad device seems to be the result of an early and partial
merge of the keypad driver. It's unused and there is no corresponding
driver available, so just remove it.
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
To use common macros to define the gpio ports for imx{1,21,25,27} the
existing ones had to made more general and a few more base address defines
were necessary.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
According to the reference manual of the i.MX25 the host controller uses an
offset of 0x200 not 0x400 as was specified in the resources for mxc_usbh2.
Needs-Testing: yes
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Group soc specific data in a global struct instead of repeating it for each
call to imxXX_add_flexcanX. The structs holding the actual data are placed
in .init.constdata and so don't do much harm. Compared to the previous
approach this reduces code size to call imx_add_flexcan.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently there is no platform data used in the driver. In case this
changes and for consistency NULL is passed unused to the soc specific
functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Currently there is no platform data used in the driver. In case this
changes NULL is passed unused to the soc specific functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Now only the virtual addresses [0xf4000000, 0xf5ffffff] are used for
static per-SoC mappings. The few mappings of whole chip selects are
moved accordingly.
The now wrong defines for virtual base addresses are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This allows changing the mapping without the need to adapt all users.
While at it remove some unneeded casts to void __iomem *, this is already
taken care for in the IO_ADDRESS macros
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This makes less code rely on the virtual constants.
To further simplify code and reduce the needed boilerplate when
defining the static mappings a new helper macro is defined in
mach/hardware.h.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This makes it more assembler friendly and allows it to be used in situation
that need an unsigned long and not a pointer. Also the naming is
clearer. IOMEM is introduced without IMX_ prefix as it is used this way
in more than one ARM subarch and it might become globally available
soon.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (215 commits)
ARM: memblock: setup lowmem mappings using memblock
ARM: memblock: move meminfo into find_limits directly
ARM: memblock: convert free_highpages() to use memblock
ARM: move freeing of highmem pages out of mem_init()
ARM: memblock: convert memory detail printing to use memblock
ARM: memblock: use memblock to free memory into arm_bootmem_init()
ARM: memblock: use memblock when initializing memory allocators
ARM: ensure membank array is always sorted
ARM: 6466/1: implement flush_icache_all for the rest of the CPUs
ARM: 6464/2: fix spinlock recursion in adjust_pte()
ARM: fix memblock breakage
ARM: 6465/1: Fix data abort accessing proc_info from __lookup_processor_type
ARM: 6460/1: ixp2000: fix type of ixp2000_timer_interrupt
ARM: 6449/1: Fix for compiler warning of uninitialized variable.
ARM: 6445/1: fixup TCM memory types
ARM: imx: Add wake functionality to GPIO
ARM: mx5: Add gpio-keys to mx51 babbage board
ARM: imx: Add gpio-keys to plat-mxc
mx31_3ds: Fix spi registration
mx31_3ds: Fix the logic for detecting the debug board
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (48 commits)
DMAENGINE: move COH901318 to arch_initcall
dma: imx-dma: fix signedness bug
dma/timberdale: simplify conditional
ste_dma40: remove channel_type
ste_dma40: remove enum for endianess
ste_dma40: remove TIM_FOR_LINK option
ste_dma40: move mode_opt to separate config
ste_dma40: move channel mode to a separate field
ste_dma40: move priority to separate field
ste_dma40: add variable to indicate valid dma_cfg
async_tx: make async_tx channel switching opt-in
move async raid6 test to lib/Kconfig.debug
dmaengine: Add Freescale i.MX1/21/27 DMA driver
intel_mid_dma: change the slave interface
intel_mid_dma: fix the WARN_ONs
intel_mid_dma: Add sg list support to DMA driver
intel_mid_dma: Allow DMAC2 to share interrupt
intel_mid_dma: Allow IRQ sharing
intel_mid_dma: Add runtime PM support
DMAENGINE: define a dummy filter function for ste_dma40
...
Currently, only two operating points: 160Mhz and 800Mhz.
the operating points are tested on babbage 3.0
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit c074512 (imx-esdhc: update devices registration) renamed
MX35_INT_MMC_SDHC2 to MX35_INT_ESDHC2 which broke expansion of the
MXC_INT_MMC_SDHC2 macro.
As (the only user of MXC_INT_MMC_SDHC2) is only used on
mx31 use the MX31 prefixed symbol to define its resources. Moreover to
reduce further confusion mxcsdhc_device0 is fixed accordingly and the MXC
prefixed symbols are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
This is only a partial revert of "ARM: mx3/mx31ads: fold board
header in its only user"
[commit ccfa7c2698)]
As some of the the board defines are also used in the cs89x0
ethernet driver by the i.MX31 ADS.
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without this exiting WFI can result in cache corruption.
Code taken from Freescale's 2.6.27 BSP and tested on i.MX35
Signed-off-by: Eric Bénard <eric@eukrea.com>
this patch fix the following errors :
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_SDMA_BASE_ADDR’ undeclared here (not in a function)
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_INT_SDMA’ undeclared here (not in a function)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Add IRAM(Internal RAM) allocation functions using GENERIC_ALLOCATOR.
The allocation size is 4KB multiples to guarantee alignment. The
idea for these functions is for i.MX platforms to use them
to dynamically allocate IRAM usage.
Applies on 2.6.36-rc7
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on work done earlier by Sascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: actually squash the two approaches together]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for the Freescale i.MX SDMA engine.
The SDMA engine is a scatter/gather DMA engine which is implemented
as a seperate coprocessor. SDMA needs its own firmware which is
requested using the standard request_firmware mechanism. The firmware
has different entry points for each peripheral type, so drivers
have to pass the peripheral type to the DMA engine which in turn
picks the correct firmware entry point from a table contained in
the firmware image itself.
The original Freescale code also supports support for transfering
data to the internal SRAM which needs different entry points to
the firmware. Support for this is currently not implemented. Also,
support for the ASRC (asymmetric sample rate converter) is skipped.
I took a very simple approach to implement dmaengine support. Only
a single descriptor is statically assigned to a each channel. This
means that transfers can't be queued up but only a single transfer
is in progress. This simplifies implementation a lot and is sufficient
for the usual device/memory transfers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Linus Walleij <linus.ml.walleij@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Addiontionally make the interrupt #defines match the base address
defines MX.._NFC_BASE_ADDR.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the imx51_3ds board, eCSPI2 is connected to a SPI NOR flash,
now add iomux definitions for those used pins.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The driver recently learned to handle platform ids. Make use of this
new feature. The up side is that the driver needs less knowledge about
the spi interfaces used on different SoCs.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Group soc specific data in a global struct instead of repeating it for
each call to imxXX_add_spi_imxX. The structs holding the actual data
are placed in .init.constdata and so don't do much harm. Compared to
the previous approach this reduces code size to call imx_add_spi_imx.
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The names used now match the processor's reference manual. Also remove
MXC from the interrupt defines to match the other imx platforms.
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This makes the header more look like the other ones, i.e.
- sort #defines by value
- use lowercase hex constants
- use a consistently named header guard
Acked-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The flexcan driver was merged as e955cead.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested it by booting a rootfs via NFS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The Enhanced Periodic Interrupt Timer (EPIT) is found on newer
i.MX SoCs and can be used as an alternative system timer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Last change I did made a big mess in function names and CONFIG names,
this patch fixes this so that the baseboard support is really built
when selected.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is a follow up to
14cb0de (arm/imx/gpio: add spinlock protection)
and fixes the following build failure:
CC arch/arm/mach-imx/pcm970-baseboard.o
In file included from arch/arm/include/asm/gpio.h:6,
from include/linux/gpio.h:8,
from arch/arm/mach-imx/pcm970-baseboard.c:20:
arch/arm/plat-mxc/include/mach/gpio.h:40: error: expected specifier-qualifier-list before 'spinlock_t'
Cc: stable@kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
This is the soc_camera support developed by Sascha Hauer for the i.MX27. Alan
Carvalho de Assis modified the original driver to get it working on more recent
kernels. I modified it further to add support for i.MX25. This driver has been
tested on i.MX25 and i.MX27 based platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The GPIO registers need protection from concurrent access for operations that
are not atomic.
Cc: stable@kernel.org
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
Reported-by: rpkamiak@rockwellcollins.com
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CPUIMX51 is build around Freescale's i.MX515 and has up to
512MB of RAM, NAND Flash, Ethernet, USB Host with 4 ports
hub, USB OTG, ST16554 Quad UART on nCS1, I2C RTC ...
MBIMX51 adds LEDS, Keypad, TSC2007 touchscreen controler ...
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as per suggested by Sascha
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to make this patch compile, even if the flexcan driver with
it's header defining the platform data isn't merged yet, two ifdefs have
been added. They effect that the "imx_add_flexcan" function results in a
no-op function if the driver hasn't been activated.
These ifdefs can be removed after the flexcan driver has been merged.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX51 generates 2 IRQ for each GPIO bank : one for gpio 0 to 15
and one for gpio 16 to 31.
Actually only the lower IRQ is registered so register the second one.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
DEBUG_LL is actually broken on i.MX25, this patch fix it.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
These GPIO bank offsets are useful when define a gpio number.
E.G. when GPIO PORTC pin 6 is used for irq request pin of external
expanding device, we can define it like:
#define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6)
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:
- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the standard place for this define is include/mach/mx25.h
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of having a platform device defined in a devices.c and register
it in the machine file allocate it dynamically. This reduces the size
of needed memory as the new function is discarded after init and only
the existing devices are created.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This fixes:
arch/arm/plat-mxc/include/mach/mxc_nand.h:25:14: error: dubious one-bit signed bitfield
arch/arm/plat-mxc/include/mach/mxc_nand.h:26:17: error: dubious one-bit signed bitfield
While at it make width unsigned, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This should be a globally available function, see
http://thread.gmane.org/gmane.linux.kernel/998881/focus=998882
Until this hits mainline create a similar function available for imx
platforms only.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This should be used instead of hard coding the corresponding platforms.
The feature test macro is needed to support different SOCs in a single
kernel image. While at it rename dma-mx1-mx2 to dma-v1 as mx25 doesn't
use it and so the mx2 part is wrong and move the header to
arch/arm/mach-imx.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* introduce 3 new flags to allow a more detailed configuration
of the SSI link :
IMX_SSI_NET : enable Network Mode
IMX_SSI_SYN : enable Synchronous Mode
IMX_SSI_USE_I2S_SLAVE : enable I2S Slave Mode
* new platform can use these settings without breaking actual
platforms.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds also the pin definition helpers in iomux-mx3.h
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch de-asserts the reset line that is connected to the USB
ULPI PHY on USB Host1.
This patch should be included with the original USB host enablement
set of patches of mx51 babbage hw, but was accidentily left out.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Eyebot robot needs the OTG port in host mode on the smartbot.
Add a new board definition so we can select the usb host/device
mode at boot with the mx31moboard_baseboard boot parameter.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes a regression of
7d58289 (mx1: prefix SOC specific defines with MX1_ and deprecate old names)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds USB HW initializiation code to /plat-mxc/ehci.c.
-Sets some specific PHY settings
Renames mxc_set_usbcontrol to mxc_initialize_usb_hw.
Adds new register bit defines for the USB HW on Freescale
SoCs.
This patch applies to 2.6.34-rc6.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is part of enabling USB for Freescale MX51 Babbage HW. This
patch updates the iomux pins for USB, and gpio line for reset the
USB hub on the MX51 Babbage HW.
This patch applies to 2.6.34-rc6.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This area contains the Nand Flash controller registers. There
is no need to map them statically as the Nand driver uses ioremap().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Freescale redboot passes the silicon revision via
ATAG_REVISION. Remove this bootloader dependency by
doing the same as redboot does in the Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This looks cleaner and allows us to call mx51_revision
later when we can use ioremap to determine the silicon
revision dynamically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed selection of COMMON_CLKDEV by CONFIG_ARCH_MX5. This is handled
in 03e09cd890.
arch/arm/plat-mxc/iomux-mx1-mx2.c was moved to
arch/arm/plat-mxc/iomux-v1.c in 5e2e95f520
and got bug fixed in 5c17ef878f. The bug
in arch/arm/plat-mxc/iomux-v1.c isn't present any more since
bac3fcfad5, so
arch/arm/plat-mxc/iomux-mx1-mx2.c is simply deleted.
Conflicts:
arch/arm/plat-mxc/Kconfig
arch/arm/plat-mxc/Makefile
arch/arm/plat-mxc/iomux-mx1-mx2.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
mxc_gpio_mode checks for invalid pins and so it returns zero for
success, -EINVAL for invalid pins.
While at it, remove definitions of GPIO_PORT_MAX removed as they are
unused now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Addionally make iomux-mx*.h headers stand-alone and similar to iomux-v3
platform files should include their platform iomux header from now on.
For now iomux.h simply includes all iomux-v1 platform headers and so
provides compatibility until all files are converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX3_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX2x_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX27_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
- fix sorting
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX25_H__ as header protector analogous to
<mach/mx...h>
- remove doxygen comments
- remove #error about mach/iomux.h which is unused on mx25
- remove #ifndef __ASSEMBLY__ which is unneeded here
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX21_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX1_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
While at it move register modification to static inlines and
so make the relevant code more readable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This is broken since at least one year when
ec996ba (mxc timer: make compile time independent)
removed the symbol MXC_TCN.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Makes it consistent with VMALLOC_START
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This baseboard is used on the handbot and eybot robots.
The sel gpios are used as enables and rst signals on smartbot, thus the
sel init is moved from mx31moboard file to board files.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add basic clock support, cpu identification, I/O mapping, interrupt
controller, serial port and ethernet.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Freescale i.MX51 processor uses a new interrupt controller. Add
driver for TrustZone Interrupt Controller
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
This simplifies the macro and makes is similar to the other
..._IO_ADDRESS macros defined for imx SOCs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Apart from MXC91231_IO_ADDRESS itself this was the only usage of
MXC91231_AIPS1_IO_ADDRESS. Now MXC91231_IO_ADDRESS can be recoded with
IMX_IO_ADDRESS and all helper macros can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Daniel Schaeffer <daniel.schaeffer@timesys.com>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Cc: Ivo Clarysse <ivo.clarysse@gmail.com>
The old names are defined only if the cpp symbol
IMX_NEEDS_DEPRECATED_SYMBOLS exists, which is defined (for now) for all
files below arch/arm/mach-mx1.
This was done earlier for mx2 and mx3, too.
USBD_INT0 is for now defined unconditionally to prevent breaking
drivers/usb/gadget/imx_udc.
While at it use IMX_IO_ADDRESS to define MX1_IO_ADDRESS which
adds a cast to the IO_ADDRESS macro fixing many warnings like
arch/arm/mach-mx1/generic.c:51: warning: passing argument 1 of 'mxc_init_irq' makes pointer from integer without a cast
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This fixes:
arch/arm/kernel/debug.S:147: Error: constant expression expected -- `ldrne r3,=(((UART1_BASE_ADDR)-AIPI_BASE_ADDR)+AIPI_BASE_ADDR_VIRT)'
arch/arm/kernel/debug.S:163: Error: constant expression expected -- `ldrne r3,=(((UART1_BASE_ADDR)-AIPI_BASE_ADDR)+AIPI_BASE_ADDR_VIRT)'
when compiling for mx2 with CONFIG_DEBUG_LL=y. A similar error exists
on mx3 and is fixed by this commit, too.
These were introduced by aae7019382.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fref is needless on mx25 since the reference clock is fixed at 24MHz.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To distinguish between mx31lite and mx31lilly boards better to use
different enum types.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because of the include of the decompress_inflate.c file from
boot/compress/misc.c, there are different flush() defines:
In file included from arch/arm/boot/compressed/misc.c:249:
arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:138:29: error: macro "flush" passed 2 arguments, but takes just 0
Fix this by removing the define of flush() in misc.c for
CONFIG_DEBUG_ICEDCC as it's already defined in mach/uncompress.h,
and that is being included unconditionally.
Also use a static inline function instead of define
for mach-mxc and mach-gemini to avoid similar bug
for those platforms.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This has the addional effect that the macros CSCR_U, CSCR_L and CSCR_A
are not used anymore in mach-pcm038.c and mach-qong.c. These still use
the deprecated IO_ADDRESS macro and shouldn't be used in new code.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Dmitriy Taychenachev <dimichxp@gmail.com>
Some headers have used (now) wrong names or havn't had protection at
all. This is needed before adding static inline functions to the
headers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Daniel Mack <daniel@caiaq.de>
This include isn't needed and hurts when defining static inline
functions in mach/hardware.h (or files included by mach/hardware.h).
The reason is that the consumers of mach/uncompress.h are compiled using
-Dstatic= so the code for all inline function is included in e.g.
arch/arm/boot/compressed/misc.o.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jörg Knobloch <knobloch@incostartec.com>
Cc: Alan Carvalho de Assis <acassis@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Dmitriy Taychenachev <dimichxp@gmail.com>
Define deprecated symbols in an #ifdef IMX_NEEDS_DEPRECATED_SYMBOLS ...
All files that still depend on the old definitions get
-DIMX_NEEDS_DEPRECATED_SYMBOLS passed to the compiler.
When all remaining users are fixed this allows including the soc
specific headers unconditionally.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Alan Carvalho de Assis <acassis@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
The WM8350 core won't actually use the range yet, but it will in
future and the platform data to configure it is there now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This just leaves cpu.c, devices.c and mm.c to clean up. As these files
are used on more than one SOC they need some more work.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Guennadi Liakhovetski <lg@denx.de>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Harro Haan <hrhaan@yahoo.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Luotao Fu <l.fu@pengutronix.de>
Cc: Ilya Yanok <yanok@emcraft.com>
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.
Users have to pass details about serial interface configuration in the
platform data.
The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch configures iomux and i2c io expander in order to add
support to SD/MMC cards on i-MXT TD60.
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is useful for audio where we do not want to setup a new scatterlist
after playing 4GB of audio data. This would cause skips in the playback.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current model does not allow to put a pad into different modes
once a pins is allocated. Remove the resource handling.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The macro mx31_revision() used to take the global variable system_rev to
determine the CPU revision number. However, this number is expected to
be set by the bootloader and is usually zero (at least on my MX31 based
boards here). More than that, it is usually taken to identify the
board's revision, not the CPU's.
Fix that by reading the the CPU's SREV register instead.
Right now, mx31_read_cpu_rev() is called from mx31_clocks_init() which
is admittedly not a good place for it. However, we need to enable the
IIM clock first, and the clock code also has conditional code that
depends on mx31_revision() returning the right thing.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit splits the support code for LogicPD's mx31lite hardware
into module and board specific parts.
This introduces a new mandatory coreparam called 'mx31lite_baseboard'
which specifies the base board support to use. For now, only the LiteKit
development board is supported, and developers of own boards are
encouraged to use that as reference.
The UART support moved to the board code.
Some comments were amended along the way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The ARC USB OTG Core has support for accessing ULPI tranceivers
through so called ULPI viewports. Export a set of function for use with
the USB OTG framework.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver has been tested on i.MX1/i.MX27/i.MX35 with an AT25 type
EEPROM and on i.MX27/i.MX31 with a Freescale MC13783 PMIC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MBIMX27 is the evaluation board for CPUIMX27 and integrates : a
QVGA TFT, a SPI touchscreen controler, a SDCard connector wired to
SDHC1.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CPUIMX27 is built around Freescale's i.MX27 and has up to 64MB of
NOR Flash, up to 512MB of NAND Flash and up to 256MB of mDDR,
it includes an ethernet PHY in MII mode, an I2C RTC and a
ST16554 QuadUART on nCS3.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The old defines leaked in from an old version of the patch.
Change the defines to match the register layout of the iomuxer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for the MT9T031 CMOS camera sensor from Aptina to the PCM037
board. Also add two I2C iomux pin definitions, needed for pcm037. Also
remove now unneeded #ifdef CONFIG_I2C_IMX.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
Using the iMX serial driver with an IrDA device
needs extra peripheral settings and specific
timing depending on the transmitter circuitry used.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sascha Hauer wrote:
> On Tue, Jun 02, 2009 at 04:18:42PM -0400, Daniel Schaeffer wrote:
>> Add basic support for the Logic i.MX27LITE board.
>>
>> Signed-off-by: Daniel Schaeffer <daniel.schaeffer@timesys.com>
>
> Besides the comment made by Fabio this looks ok to me.
>
> Sascha
>
>
Fixed issues pointed out by Fabio and Magnus, and rebased to mxc-master head.
Signed-off-by: Daniel Schaeffer <daniel.schaeffer@timesys.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support code for lilly-1131 is implemented in a module/baseboard
fashion. All code specific to peripherals found on the development board
will go to this file.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for INCO startec's LILLY-1131 iMX31 based
modules. The module needs a baseboard support to work which will be
added in the next patch.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX31 PDK consists of several boards, one of them is a debug
board containing a CPLD which controls some debug leds, switch
buttons, an interrupt chip and an Ethernet controller.
This patch adds support for detecting if the PDK board is present
(during boot) and adds the interrupt chip to the kernel.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since iomux code is not directly related to gpio on mx31, the calls
to gpio_request are removed from iomux.c file.
These calls have to be done in platform initialization files. The
name of the singe pin call for iomux is also changed to
mxc_iomux_alloc_pin.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several comments in board config files stated "mandatory for
CONFIG_LL_DEBUG" but the correct name is CONFIG_DEBUG_LL.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As suggested by Sascha, I regroup them in a single patch so that the
other patches become more orthogonal.
changes since v1: changed I2C1 pin names
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[PATCH v6] MXC: mx21ads base support
Base machine support for the Freescale i.MX21ADS
(M9328MX21ADSE) Application Development System.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MXC GPIO controller does not support generation of interrupts on both
edges. Emulate this mode in software by reconfiguring the irq trigger
polarity on each interrupt. This follows an example of
drivers/mfd/asic3.c.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently we depend on hardcoded base addresses for the timer.
This prevents us from compiling in more than one i.MX architecture
at a time. This patch changes the base address to a runtime
calculated one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Lothar Waßmann