One thing this change pointed out was that we really should
pull the "get 'local-mac-address' property" logic into a helper
function all the network drivers can call.
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the in-kernel PROM device tree isn't built yet,
and therefore the present cpu bits don't get set properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
On some sun4v systems, after netboot the ethernet controller and it's
DMA mappings can be left active. The net result is that the kernel
can end up using memory the ethernet controller will continue to DMA
into, resulting in corruption.
To deal with this, we are more careful about importing IOMMU
translations which OBP has left in the IO-TLB. If the mapping maps
into an area the firmware claimed was free and available memory for
the kernel to use, we demap instead of import that IOMMU entry.
This is going to cause the network chip to take a PCI master abort on
the next DMA it attempts, if it has been left going like this. All
tests show that this is handled properly by the PCI layer and the e1000
drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we end up zero'ing out the size of one of the entries,
pop it out of the array completely because some code that
examines these things cannot handle a zero length element
properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
The basic framework is based on the PowerPC OF code.
This code even tries to get the device addressing components
correct in the full path names.
Signed-off-by: David S. Miller <davem@davemloft.net>
Give the statfs superblock operation a dentry pointer rather than a superblock
pointer.
This complements the get_sb() patch. That reduced the significance of
sb->s_root, allowing NFS to place a fake root there. However, NFS does
require a dentry to use as a target for the statfs operation. This permits
the root in the vfsmount to be used instead.
linux/mount.h has been added where necessary to make allyesconfig build
successfully.
Interest has also been expressed for use with the FUSE and XFS filesystems.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nathan Scott <nathans@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the long overdue conversion of sparc64 over to
the generic IRQ layer.
The kernel image is slightly larger, but the BSS is ~60K
smaller due to the reduced size of struct ino_bucket.
A lot of IRQ implementation details, including ino_bucket,
were moved out of asm-sparc64/irq.h and are now private to
arch/sparc64/kernel/irq.c, and most of the code in irq.c
totally disappeared.
One thing that's different at the moment is IRQ distribution,
we do it at enable_irq() time. If the cpu mask is ALL then
we round-robin using a global rotating cpu counter, else
we pick the first cpu in the mask to support single cpu
targetting. This is similar to what powerpc's XICS IRQ
support code does.
This works fine on my UP SB1000, and the SMP build goes
fine and runs on that machine, but lots of testing on
different setups is needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by PowerPC XICS interrupt support code.
All IRQs are virtualized in order to keep NR_IRQS from needing
to be too large. Interrupts on sparc64 are arbitrary 11-bit
values, but we don't need to define NR_IRQS to 2048 if we
virtualize the IRQs.
As PCI and SBUS controller drivers build device IRQs, we divy
out virtual IRQ numbers incrementally starting at 1. Zero is
a special virtual IRQ used for the timer interrupt.
So device drivers all see virtual IRQs, and all the normal
interfaces such as request_irq(), enable_irq(), etc. translate
that into a real IRQ number in order to configure the IRQ.
At this point knowledge of the struct ino_bucket is almost
entirely contained within arch/sparc64/kernel/irq.c There are
a few small bits in the PCI controller drivers that need to
be swept away before we can remove ino_bucket's definition
out of asm-sparc64/irq.h and privately into kernel/irq.c
Signed-off-by: David S. Miller <davem@davemloft.net>
And reuse that struct member for virt_irq, which will
be used in future changesets for the implementation of
mapping between real and virtual IRQ numbers.
This nicely kills off a ton of SBUS and PCI controller
PIL assignment code which is no longer necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only pil0_dummy_bucket had a pil of zero and we just killed that
off, so we can delete all special case code that used bp->pil==0
as a way to identify a dummy bucket.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first in a series of cleanups that will hopefully
allow a seamless attempt at using the generic IRQ handling
infrastructure in the Linux kernel.
Define PIL_DEVICE_IRQ and vector all device interrupts through
there.
Get rid of the ugly pil0_dummy_{bucket,desc}, instead vector
the timer interrupt directly to a specific handler since the
timer interrupt is the only event that will be signaled on
PIL 14.
The irq_worklist is now in the per-cpu trap_block[].
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing PCI config space accesses to non-present PCI slots
can result in fatal JBUS errors if the PCI config access
hypervisor call is performed on cpus other than the boot
cpu.
PCI config space accesses to present PCI slots works just
fine.
Recursively traverse the OBP device tree under the PCI
controller node and record all present device IDs into
a small hash table.
Avoid the hypervisor call for any PCI config space access
attempt for a device not recorded in the hash table.
Signed-off-by: David S. Miller <davem@davemloft.net>
Both csum_partial() and the csum_partial_copy*() family of routines
forget to do a final fold on the computed checksum value on sparc64.
So do the standard Sparc "add + set condition codes, add carry"
sequence, then make sure the high 32-bits of the return value are
clear.
Based upon some excellent detective work and debugging done by
Richard Braun and Samuel Thibault.
Signed-off-by: David S. Miller <davem@davemloft.net>
Uses of smp_processor_id() get pushed earlier and earlier in
the start_kernel() sequence. So just get it working before
we call start_kernel() to avoid all possible problems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Using asm-generic/dma-mapping.h does not work because pushing
the call down to pci_alloc_coherent() causes the gfp_t argument
of dma_alloc_coherent() to be ignored.
Fix this by implementing things directly, and adding a gfp_t
argument we can use in the internal call down to the PCI DMA
implementation of pci_alloc_coherent().
This fixes massive memory corruption when using the sound driver
layer, which passes things like __GFP_COMP down into these
routines and (correctly) expects that to work.
Signed-off-by: David S. Miller <davem@davemloft.net>
For sparc32 we need R_SPARC_UA32 relocation support, for
sparc64 we need the handle R_SPARC_DISP32 relocations.
Based upon reports and initial patch by Martin Habets.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'audit.b10' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] Audit Filter Performance
[PATCH] Rework of IPC auditing
[PATCH] More user space subject labels
[PATCH] Reworked patch for labels on user space messages
[PATCH] change lspp ipc auditing
[PATCH] audit inode patch
[PATCH] support for context based audit filtering, part 2
[PATCH] support for context based audit filtering
[PATCH] no need to wank with task_lock() and pinning task down in audit_syscall_exit()
[PATCH] drop task argument of audit_syscall_{entry,exit}
[PATCH] drop gfp_mask in audit_log_exit()
[PATCH] move call of audit_free() into do_exit()
[PATCH] sockaddr patch
[PATCH] deal with deadlocks in audit_free()
A context switch will force a call to flush_tlb_pending() (via
switch_to()), so if we test tlb_nr to be non-zero, then sleep, it
would become zero and later back at the original context we'll pass
zero down into the TLB flushing code which should never see a nr
argument of zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes. There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.
This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines. Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes dependencies of HUGETLB_PAGE_SIZE_64K
Signed-off-by: Jean-Luc Léger <jean-luc.leger@dspnet.fr.eu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While cleaning up parisc_ksyms.c earlier, I noticed that strpbrk wasn't
being exported from lib/string.c. Investigating further, I noticed a
changeset that removed its export and added it to _ksyms.c on a few more
architectures. The justification was that "other arches do it."
I think this is wrong, since no architecture currently defines
__HAVE_ARCH_STRPBRK, there's no reason for any of them to be exporting it
themselves. Therefore, consolidate the export to lib/string.c.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
for sparc64.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Otherwise the build breaks with EXPERIMENTAL disabled
because SPARSEMEM will not get selected properly. See
mm/Kconfig for how that works.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Take doc-book function comment from i386 implementation.
2) cacheline align call_lock, taken from powerpc
3) Need memory barrier after setting call_data
4) Remove timeout
Signed-off-by: David S. Miller <davem@davemloft.net>
GDB uses a PTRACE_PEEKUSR call with offset 0 to see
if a thread is alive, so provide a success return for
this particular special case.
Signed-off-by: David S. Miller <davem@davemloft.net>
We are about to fill in all HPAGE_SIZE's worth
of PAGE_SIZE ptes, so we have to give the first
pte in that set else we scribble over random memory
when we fill in the ptes.
Signed-off-by: David S. Miller <davem@davemloft.net>
switch_mm() changes the mm state and does a tsb_context_switch()
first, then we do the cpu register state switch which changes
current_thread_info() and current().
So it's safer to check the PGD physical address stored in the
trap block (which will be updated by the tsb_context_switch() in
switch_mm()) than current->active_mm.
Technically we should never run here in between those two
updates, because interrupts are disabled during the entire
context switch operation. But some day we might like to leave
interrupts enabled during the context switch and this change
allows that to happen without any surprises.
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The worst part about this bug is what it would cause
a hugepage TSB to be allocated for every address space
since "0 >= 0".
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide proper kprobes fault handling, if a user-specified pre/post handlers
tries to access user address space, through copy_from_user(), get_user() etc.
The user-specified fault handler gets called only if the fault occurs while
executing user-specified handlers. In such a case user-specified handler is
allowed to fix it first, later if the user-specifed fault handler does not fix
it, we try to fix it by calling fix_exception().
The user-specified handler will not be called if the fault happens when single
stepping the original instruction, instead we reset the current probe and
allow the system page fault handler to fix it up.
I could not test this patch for sparc64.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently kprobe handler traps only happen in kernel space, so function
kprobe_exceptions_notify should skip traps which happen in user space.
This patch modifies this, and it is based on 2.6.16-rc4.
Signed-off-by: bibo mao <bibo.mao@intel.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "Keshavamurthy, Anil S" <anil.s.keshavamurthy@intel.com>
Cc: <hiramatu@sdl.hitachi.co.jp>
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create compat_sys_adjtimex and use it an all appropriate places.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We had a copy of the compatibility version of struct timex in each 64 bit
architecture. This patch just creates a global one and replaces all the
usages of the old ones.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Kconfig text for CONFIG_DEBUG_SLAB and CONFIG_DEBUG_PAGEALLOC have always
seemed a bit confusing. Change them to:
CONFIG_DEBUG_SLAB: "Debug slab memory allocations"
CONFIG_DEBUG_PAGEALLOC: "Debug page memory allocations"
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merge clash will have broken sparc64. Synch up its online_page
implementation with powerpc, which was identical until the
set_page_count removal.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Add a secondary TSB for hugepage mappings.
[SPARC]: Respect vm_page_prot in io_remap_page_range().
Quite a long time back, prepare_hugepage_range() replaced
is_aligned_hugepage_range() as the callback from mm/mmap.c to arch code to
verify if an address range is suitable for a hugepage mapping.
is_aligned_hugepage_range() stuck around, but only to implement
prepare_hugepage_range() on archs which didn't implement their own.
Most archs (everything except ia64 and powerpc) used the same
implementation of is_aligned_hugepage_range(). On powerpc, which
implements its own prepare_hugepage_range(), the custom version was never
used.
In addition, "is_aligned_hugepage_range()" was a bad name, because it
suggests it returns true iff the given range is a good hugepage range,
whereas in fact it returns 0-or-error (so the sense is reversed).
This patch cleans up by abolishing is_aligned_hugepage_range(). Instead
prepare_hugepage_range() is defined directly. Most archs use the default
version, which simply checks the given region is aligned to the size of a
hugepage. ia64 and powerpc define custom versions. The ia64 one simply
checks that the range is in the correct address space region in addition to
being suitably aligned. The powerpc version (just as previously) checks
for suitable addresses, and if necessary performs low-level MMU frobbing to
set up new areas for use by hugepages.
No libhugetlbfs testsuite regressions on ppc64 (POWER5 LPAR).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1) huge_pte_offset() did not check the page table hierarchy
elements as being empty correctly, resulting in an OOPS
2) Need platform specific hugetlb_get_unmapped_area() to handle
the top-down vs. bottom-up address space allocation strategies.
Signed-off-by: David S. Miller <davem@davemloft.net>
init/do_mounts_rd.c depends upon CONFIG_BLK_DEV_RAM, not CONFIG_BLK_DEV_INITRD.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to write an invalid tag every 16 bytes,
so taking advantage of this can save many instructions
compared to the simple memset() call we make now.
A prefetching implementation is implemented for sun4u
and a block-init store version if implemented for Niagara.
The next trick is to be able to perform an init and
a copy_tsb() in parallel when growing a TSB table.
Signed-off-by: David S. Miller <davem@davemloft.net>
online_page() is straightforward, and then add a dummy
remove_memory() that returns -EINVAL just like i386.
There is no point in implementing remove_memory() since
__remove_pages() has no implementation either.
Signed-off-by: David S. Miller <davem@davemloft.net>
Try only lightly on > 1 order allocations.
If a grow fails, we are under memory pressure, so do not try
to grow the TSB for this address space any more.
If a > 0 order TSB allocation fails on a new fork, retry using
a 0 order allocation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Put it one page below the top of the 32-bit address space.
This gives us ~16MB more address space to work with.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently allocations are very constrained for 32-bit processes.
It grows down-up from 0x70000000 to 0xf0000000 which gives about
2GB of stack + dynamic mmap() space.
So support the top-down method, and we need to override the
generic helper function in order to deal with D-cache coloring.
With these changes I was able to squeeze out a mmap() just over
3.6GB in size in a 32-bit process.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is good for up to %50 performance improvement of some test cases.
The problem has been the race conditions, and hopefully I've plugged
them all up here.
1) There was a serious race in switch_mm() wrt. lazy TLB
switching to and from kernel threads.
We could erroneously skip a tsb_context_switch() and thus
use a stale TSB across a TSB grow event.
There is a big comment now in that function describing
exactly how it can happen.
2) All code paths that do something with the TSB need to be
guarded with the mm->context.lock spinlock. This makes
page table flushing paths properly synchronize with both
TSB growing and TLB context changes.
3) TSB growing events are moved to the end of successful fault
processing. Previously it was in update_mmu_cache() but
that is deadlock prone. At the end of do_sparc64_fault()
we hold no spinlocks that could deadlock the TSB grow
sequence. We also have dropped the address space semaphore.
While we're here, add prefetching to the copy_tsb() routine
and put it in assembler into the tsb.S file. This piece of
code is quite time critical.
There are some small negative side effects to this code which
can be improved upon. In particular we grab the mm->context.lock
even for the tsb insert done by update_mmu_cache() now and that's
a bit excessive. We can get rid of that locking, and the same
lock taking in flush_tsb_user(), by disabling PSTATE_IE around
the whole operation including the capturing of the tsb pointer
and tsb_nentries value. That would work because anyone growing
the TSB won't free up the old TSB until all cpus respond to the
TSB change cross call.
I'm not quite so confident in that optimization to put it in
right now, but eventually we might be able to and the description
is here for reference.
This code seems very solid now. It passes several parallel GCC
bootstrap builds, and our favorite "nut cruncher" stress test which is
a full "make -j8192" build of a "make allmodconfig" kernel. That puts
about 256 processes on each cpu's run queue, makes lots of process cpu
migrations occur, causes lots of page table and TLB flushing activity,
incurs many context version number changes, and it swaps the machine
real far out to disk even though there is 16GB of ram on this test
system. :-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Report 'sun4v' when appropriate in /proc/cpuinfo
Remove all the verifications of the OBP version string. Just
make sure it's there, and report it raw in the bootup logs and
via /proc/cpuinfo.
Signed-off-by: David S. Miller <davem@davemloft.net>
The mapping is a simple "(cpuid >> 2) == core" for now.
Later we'll add more sophisticated code that will walk
the sun4v machine description and figure this out from
there.
We should also add core mappings for jaguar and panther
processors.
Signed-off-by: David S. Miller <davem@davemloft.net>
The page->flags manipulations done by the D-cache dirty
state tracking was broken because the constants were not
marked with "UL" to make them 64-bit, which means we were
clobbering the upper 32-bits of page->flags all the time.
This doesn't jive well with sparsemem which stores the
section and indexing information in the top 32-bits of
page->flags.
This is yet another sparc64 bug which has been with us
forever.
While we're here, tidy up some things in bootmem_init()
and paginig_init():
1) Pass min_low_pfn to init_bootmem_node(), it's identical
to (phys_base >> PAGE_SHIFT) but we should use consistent
with the variable names we print in CONFIG_BOOTMEM_DEBUG
2) max_mapnr, although no longer used, was being set
inaccurately, we shouldn't subtract pfn_base any more.
3) All the games with phys_base in the zones_*[] arrays
we pass to free_area_init_node() are no longer necessary.
Thanks to Josh Grebe and Fabbione for the bug reports
and testing. Fix also verified locally on an SB2500
which had a memory layout that triggered the same problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been pending for a long time, and the fact
that we waste a ton of ram on some configurations
kind of pushed things over the edge.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't piggy back the SMP receive signal code to do the
context version change handling.
Instead allocate another fixed PIL number for this
asynchronous cross-call. We can't use smp_call_function()
because this thing is invoked with interrupts disabled
and a few spinlocks held.
Also, fix smp_call_function_mask() to count "cpus" correctly.
There is no guarentee that the local cpu is in the mask
yet that is exactly what this code was assuming.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Always spin_lock_init() in init_context(). The caller essentially
clears it out, or copies the mm info from the parent. In both
cases we need to explicitly initialize the spinlock.
2) Always do explicit IRQ disabling while taking mm->context.lock
and ctx_alloc_lock.
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch converts arch/sparc64 to kzalloc usage.
Crosscompile tested with allyesconfig.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we were aligned, but didn't have at least 256MB left
to process, we would loop forever.
Thanks to fabbione for the report and testing the fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't try to avoid putting non-base page sized entries
into the user TSB. It actually costs us more to check
this than it helps.
Eventually we'll have a multiple TSB scheme for user
processes. Once a process starts using larger pages,
we'll allocate and use such a TSB.
Signed-off-by: David S. Miller <davem@davemloft.net>
This cpu mondo sending interface isn't all that easy to
use correctly...
We were clearing out the wrong bits from the "mask" after getting
something other than EOK from the hypervisor.
It turns out the hypervisor can just be resent the same cpu_list[]
array, with the 0xffff "done" entries still in there, and it will do
the right thing.
So don't update or try to rebuild the cpu_list[] array to condense it.
This requires the "forward_progress" check to be done slightly
differently, but this new scheme is less bug prone than what we were
doing before.
Signed-off-by: David S. Miller <davem@davemloft.net>
We were clobbering a base register before we were done
using it. Fix a comment typo while we're here.
Signed-off-by: David S. Miller <davem@davemloft.net>
The UltraSPARC T1 manual recommends this because the chip
could instruction prefetch into the VA hole, and this would
also make decoding certain kinds of memory access traps
more difficult (because the chip sign extends certain pieces
of trap state).
Signed-off-by: David S. Miller <davem@davemloft.net>
First of all, use the known _PAGE_EXEC_{4U,4V} value instead
of loading _PAGE_EXEC from memory. We either know which one
to use by context, or we can code patch the test.
Next, we need to check executability of a PTE in the generic
TSB miss handler.
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several bugs in the SUN4V cpu mondo dispatch code.
In fact, if we ever got a EWOULDBLOCK or other error from
the hypervisor call, we'd potentially send a cpu mondo multiple
times to the same cpu and even worse we could loop until the
timeout resending the same mondo over and over to such cpus.
So let's bulletproof this thing as follows:
1) Implement cpu_mondo_send() and cpu_state() hypervisor calls
in arch/sparc64/kernel/entry.S, add prototypes to asm/hypervisor.h
2) Don't build and update the cpulist using inline functions, this
was causing the cpu mask to not get updated in the caller.
3) Disable interrupts during the entire mondo send, otherwise our
cpu list and/or mondo block could get overwritten if we take
an interrupt and do a cpu mondo send on the current cpu.
4) Check for all possible error return types from the cpu_mondo_send()
hypervisor call. In particular:
HV_EOK) Our work is done, all cpus have received the mondo.
HV_CPUERROR) One or more of the cpus in the cpu list we passed
to the hypervisor are in error state. Use cpu_state()
calls over the entries in the cpu list to see which
ones. Record them in "error_mask" and report this
after we are done sending the mondo to cpus which are
not in error state.
HV_EWOULDBLOCK) We need to keep trying.
Any other error we consider fatal, we report the event and exit
immediately.
5) We only timeout if forward progress is not made. Forward progress
is defined as having at least one cpu get the mondo successfully
in a given cpu_mondo_send() call. Otherwise we bump a counter
and delay a little. If the counter hits a limit, we signal an
error and report the event.
Also, smp_call_function_mask() error handling reports the number
of cpus incorrectly.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) We must flush the TLB, duh.
2) Even if the sw context was seen to be valid, the local cpu's
hw context can be out of date, so reload it unconditionally.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check TLB flush hypervisor calls for errors and report them.
Pass HV_MMU_ALL always for now, we can add back the optimization
to avoid the I-TLB flush later.
Always explicitly page align the virtual address arguments.
Signed-off-by: David S. Miller <davem@davemloft.net>
get_new_mmu_context() can be invoked from interrupt context
now for the new SMP version wrap handling.
So disable interrupt while taking ctx_alloc_lock in destroy_context()
so we don't deadlock.
Signed-off-by: David S. Miller <davem@davemloft.net>
The context allocation scheme we use depends upon there being a 1<-->1
mapping from cpu to physical TLB for correctness. Chips like Niagara
break this assumption.
So what we do is notify all cpus with a cross call when the context
version number changes, and if necessary this makes them allocate
a valid context for the address space they are running at the time.
Stress tested with make -j1024, make -j2048, and make -j4096 kernel
builds on a 32-strand, 8 core, T2000 with 16GB of ram.
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise with too much stuff enabled in the kernel config
we can end up with an unaligned trap table.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we take a window fault, on SUN4V set %gl to zero before we
turn PSTATE_IE back on in %pstate. Otherwise if we take an
interrupt we'll end up with corrupt register state.
Signed-off-by: David S. Miller <davem@davemloft.net>
It can map all of the linear kernel mappings with zero TSB hash
conflicts for systems with 16GB or less ram. In such cases, on
SUN4V, once we load up this TSB the first time with all the
mappings, we never take a linear kernel mapping TLB miss ever
again, the hypervisor handles them all.
Signed-off-by: David S. Miller <davem@davemloft.net>
We use a bitmap, one bit for every 256MB of memory. If the
bit is set we can use a 256MB PTE for linear mappings, else
we have to use a 4MB PTE.
SUN4V support is there, and we can very easily add support
for Panther cpu 256MB PTEs in the future.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to turn off the "polling nrflag" bit when we sleep
the cpu like this, so that we'll get a cross-cpu interrupt
to wake the processor up from the yield.
We also have to disable PSTATE_IE in %pstate around the yield
call and recheck need_resched() in order to avoid any races.
Signed-off-by: David S. Miller <davem@davemloft.net>
Set, but never used.
We used to use this for dynamic IRQ retargetting, but that
code died a long time ago.
Signed-off-by: David S. Miller <davem@davemloft.net>
They were getting truncated to 32-bit and this is very bad
when your MMU fault status area is in physical memory above
4GB on SUN4V.
Signed-off-by: David S. Miller <davem@davemloft.net>
The math-emu code only expects unfinished fpop traps when
emulating FPU sqrt instructions on pre-Niagara chips.
On Niagara we can get unimplemented fpop, so handle that.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's extremely noisy and causes much grief on slow
consoles with large numbers of cpus.
We'll have to provide this some saner way in order
to re-enable this.
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to seriously die in these cases so it is important
that the messages make it to the console.
Signed-off-by: David S. Miller <davem@davemloft.net>
Another case where we have to force ourselves into global register
level one. Also make sure the arguments passed to sun4v_do_mna() are
correct.
This area actually needs some more work, for example spill fixup is
not necessarily going to do the right thing for this case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like kvmap_dtlb_longpath we have to force the
global register level to one in order to mimick the
PSTATE_MG --> PSTATE_AG trasition done on SUN4U.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SUN4V convention with non-shared TSBs is that the context
bit of the TAG is clear. So we have to choose an "invalid"
bit and initialize new TSBs appropriately. Otherwise a zero
TAG looks "valid".
Make sure, for the window fixup cases, that we use the right
global registers and that we don't potentially trample on
the live global registers in etrap/rtrap handling (%g2 and
%g6) and that we put the missing virtual address properly
in %g5.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Add error return checking for TLB load hypervisor
calls.
2) Don't fallthru to dtlb tsb miss handler from itlb tsb
miss handler, oops.
3) On window fixups, propagate fault information to fixup
handler correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>
This gives more consistent bogomips and delay() semantics,
especially on sun4v. It gives weird looking values though...
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use the real hardware processor ID when
targetting interrupts, not the "define to 0" thing
the uniprocessor build gives us.
Also, fill in the Node-ID and Agent-ID fields properly
on sun4u/Safari.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the top-level cnode had multi entries in it's "reg"
property, we'd fail. The buffer wasn't large enough in
such cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sibling cpu bringup is extremely fragile. We can only
perform the most basic calls until we take over the trap
table from the firmware/hypervisor on the new cpu.
This means no accesses to %g4, %g5, %g6 since those can't be
TLB translated without our trap handlers.
In order to achieve this:
1) Change sun4v_init_mondo_queues() so that it can operate in
several modes.
It can allocate the queues, or install them in the current
processor, or both.
The boot cpu does both in it's call early on.
Later, the boot cpu allocates the sibling cpu queue, starts
the sibling cpu, then the sibling cpu loads them in.
2) init_cur_cpu_trap() is changed to take the current_thread_info()
as an argument instead of reading %g6 directly on the current
cpu.
3) Create a trampoline stack for the sibling cpus. We do our basic
kernel calls using this stack, which is locked into the kernel
image, then go to our proper thread stack after taking over the
trap table.
4) While we are in this delicate startup state, we put 0xdeadbeef
into %g4/%g5/%g6 in order to catch accidental accesses.
5) On the final prom_set_trap_table*() call, we put &init_thread_union
into %g6. This is a hack to make prom_world(0) work. All that
wants to do is restore the %asi register using
get_thread_current_ds().
Longer term we should just do the OBP calls to set the trap table by
hand just like we do for everything else. This would avoid that silly
prom_world(0) issue, then we can remove the init_thread_union hack.
Signed-off-by: David S. Miller <davem@davemloft.net>
For 32 cpus and a slow console, it just wedges the
machine especially with DETECT_SOFTLOCKUP enabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole algorithm was wrong. What we need to do is:
1) Walk each PCI bus above this device on the path to the
PCI controller nexus, and for each:
a) If interrupt-map exists, apply it, record IRQ controller node
b) Else, swivel interrupt number using PCI_SLOT(), use PCI bus
parent OBP node as controller node
c) Walk up to "controller node" until we hit the first PCI bus
in this domain, or "controller node" is the PCI controller
OBP node
2) If we walked to PCI controller OBP node, we're done.
3) Else, apply PCI controller interrupt-map to interrupt.
There is some stuff that needs to be checked out for ebus and
isa, but the PCI part is good to go.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to set the global register set _AND_ disable
PSTATE_IE in %pstate. The original patch sequence was
leaving PSTATE_IE enabled when returning to kernel mode,
oops.
This fixes the random register corruption being seen
on SUN4V.
Signed-off-by: David S. Miller <davem@davemloft.net>
Forgot to multiply by 8 * 1024, oops. Correct the size constant when
the virtual-dma arena is 2GB in size, it should bet 256 not 128.
Finally, log some info about the TSB at probe time.
Signed-off-by: David S. Miller <davem@davemloft.net>
For SUN4V, we were clobbering %o5 to do the hypervisor call.
This clobbers the saved %pstate value and we end up writing
garbage into that register as a result. Oops.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use prom_startcpu_cpuid() on SUN4V instead of prom_startcpu().
We should really test for "SUNW,start-cpu-by-cpuid" presence
and use it if present even on SUN4U.
Signed-off-by: David S. Miller <davem@davemloft.net>
When crawling up the PCI bus chain, stop at the first node
that has an interrupt-map property before we hit the root.
Also, if we use a bus interrupt-{map,mask} do not forget to
update the 'intmask' pointer as we do for the 'intmap' pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
On SUN4V, force IRQ state to idle in enable_irq(). However,
I'm still not sure this is %100 correct.
Call add_interrupt_randomness() on SUN4V too.
Signed-off-by: David S. Miller <davem@davemloft.net>
On the PBM's first bus number, only allow device 0, function 0, to be
poked at with PCI config space accesses.
For some reason, this single device responds to all device numbers.
Also, reduce the verbiage of the debugging log printk's for PCI cfg
space accesses in the SUN4V PCI controller driver, so that it doesn't
overwhelm the slow SUN4V hypervisor console.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should dynamically allocate the per-cpu pglist not use
an in-kernel-image datum, since __pa() does not work on
such addresses.
Also, consistently use "u32" for devhandle.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add udelay to polling console write loop, and increment
the loop limit.
Name the device "ttyHV" and pass that to add_preferred_console()
when we're using hypervisor console.
Kill sunhv_console_setup(), it's empty.
Handle the case where we don't want to use hypervisor console.
(ie. we have a head attached to a sun4v machine)
Signed-off-by: David S. Miller <davem@davemloft.net>
Get bus range from child of PCI controller root nexus.
This is actually a hack, but the PCI-E bridge sitting
at the top of the PCI tree responds to PCI config cycles
for every device number, so best to just ignore it for now.
Preliminary PCI irq routing, needs lots of work.
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear top 8-bits of physical addresses in "ranges" property.
This gives the actual physical address.
Detect PBM-A vs. PBM-B by checking bit 0x40 of the devhandle.
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI cfg space is accessed transparently through the Hypervisor and not
through direct cpu PIO operations.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to use bootmem during init_IRQ and page alloc
for sibling cpu calls.
Also, fix incorrect hypervisor call return value
checks in the hypervisor SMP cpu mondo send code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Yes, you heard it right, they changed the PTE layout for
SUN4V. Ho hum...
This is the simple and inefficient way to support this.
It'll get optimized, don't worry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Code patching did not sign extend negative branch
offsets correctly.
Kernel TLB miss path needs patching and %g4 register
preservation in order to handle SUN4V correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>
prom_sun4v_name should be "sun4v" not "SUNW,sun4v"
Also, this is too early to make use of the
.sun4v_Xinsn_patch code patching, so just check
things manually.
This gets us at least to prom_init() on Niagara.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to restore the %asi register properly.
For the kernel this means get_fs(), for user this
means ASI_PNF.
Also, NGcopy_to_user.S was including U3memcpy.S instead
of NGmemcpy.S, oops :-)
Signed-off-by: David S. Miller <davem@davemloft.net>
There was also a bug in sun4v_itlb_miss, it loaded the
MMU Fault Status base into %g3 instead of %g2.
This pointed out a fast path for TSB miss processing,
since we have %g2 with the MMU Fault Status base, we
can use that to quickly load up the PGD phys address.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is where the virtual address of the fault status
area belongs.
To set it up we don't make a hypervisor call, instead
we call OBP's SUNW,set-trap-table with the real address
of the fault status area as the second argument. And
right before that call we write the virtual address into
ASI_SCRATCHPAD vaddr 0x0.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add assembler file for PCI hypervisor calls.
Setup basic skeleton of SUN4V PCI controller driver.
Add 32-bit devhandle to PBM struct, as this is needed for
hypervisor calls.
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract out IOMMU operations so that we can have a different
set of calls on sun4v, which needs to do things through
hypervisor calls.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we register a TSB with the hypervisor, so that it or hardware can
handle TLB misses and do the TSB walk for us, the hypervisor traps
down to these trap when it incurs a TSB miss.
Processing is simple, we load the missing virtual address and context,
and do a full page table walk.
Signed-off-by: David S. Miller <davem@davemloft.net>
We look for "SUNW,sun4v" in the 'compatible' property
of the root OBP device tree node.
Protect every %ver register access, to make sure it is
not touched on sun4v, as %ver is hyperprivileged there.
Lock kernel TLB entries using hypervisor calls instead of
calls into OBP.
Signed-off-by: David S. Miller <davem@davemloft.net>
Technically the hypervisor call supports sending in a list
of all cpus to get the cross-call, but I only pass in one
cpu at a time for now.
The multi-cpu support is there, just ifdef'd out so it's easy to
enable or delete it later.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sun4v has 4 interrupt queues: cpu, device, resumable errors,
and non-resumable errors. A set of head/tail offset pointers
help maintain a work queue in physical memory. The entries
are 64-bytes in size.
Each queue is allocated then registered with the hypervisor
as we bring cpus up.
The two error queues each get a kernel side buffer that we
use to quickly empty the main interrupt queue before we
call up to C code to log the event and possibly take evasive
action.
Signed-off-by: David S. Miller <davem@davemloft.net>
Happily we have no D-cache aliasing issues on these
chips, so the implementation is very straightforward.
Add a stub in bootup which will be where the patching
calls will be made for niagara/sun4v/hypervisor.
Signed-off-by: David S. Miller <davem@davemloft.net>
Things are a little tricky because, unlike sun4u, we have
to:
1) do a hypervisor trap to do the TLB load.
2) do the TSB lookup calculations by hand
Signed-off-by: David S. Miller <davem@davemloft.net>
If we're just switching between different alternate global
sets, nop it out on sun4v. Also, get rid of all of the
alternate global save/restore in the OBP CIF trampoline code.
Signed-off-by: David S. Miller <davem@davemloft.net>
They are totally unnecessary because:
1) Interrupts are already disabled when switch_to()
runs.
2) We don't use hard-coded alternate globals any longer.
This found a case in rtrap, which still assumed alternate
global %g6 was current_thread_info(), and that is fixed
by this changeset as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
As we save trap state onto the stack, the store buffer fills up
mid-way through and we stall for several cycles as the store buffer
trickles out to the L2 cache. Meanwhile we can do some privileged
register reads and other calculations, essentially for free.
Signed-off-by: David S. Miller <davem@davemloft.net>
And more consistently check cheetah{,_plus} instead
of assuming anything not spitfire is cheetah{,_plus}.
Signed-off-by: David S. Miller <davem@davemloft.net>
When saving and restoing trap state, do the window spill/fill
handling inline so that we never trap deeper than 2 trap levels.
This is important for chips like Niagara.
The window fixup code is massively simplified, and many more
improvements are now possible.
Signed-off-by: David S. Miller <davem@davemloft.net>
On uniprocessor, it's always zero for optimize that.
On SMP, the jmpl to the stub kills the return address stack in the cpu
branch prediction logic, so expand the code sequence inline and use a
code patching section to fix things up. This also always better and
explicit register selection, which will be taken advantage of in a
future changeset.
The hard_smp_processor_id() function is big, so do not inline it.
Fix up tests for Jalapeno to also test for Serrano chips too. These
tests want "jbus Ultra-IIIi" cases to match, so that is what we should
test for.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several tricky races involved with growing the TSB. So just
use base-size TSBs for user contexts and we can revisit enabling this
later.
One part of the SMP problems is that tsb_context_switch() can see
partially updated TSB configuration state if tsb_grow() is running in
parallel. That's easily solved with a seqlock taken as a writer by
tsb_grow() and taken as a reader to capture all the TSB config state
in tsb_context_switch().
Then there is flush_tsb_user() running in parallel with a tsb_grow().
In theory we could take the seqlock as a reader there too, and just
resample the TSB pointer and reflush but that looks really ugly.
Lastly, I believe there is a case with threads that results in a TSB
entry lock bit being set spuriously which will cause the next access
to that TSB entry to wedge the cpu (since the TSB entry lock bit will
never clear). It's either copy_tsb() or some bug elsewhere in the TSB
assembly.
Signed-off-by: David S. Miller <davem@davemloft.net>
The are distrupting, which by the sparc v9 definition means they
can only occur when interrupts are enabled in the %pstate register.
This never occurs in any of the trap handling code running at
trap levels > 0.
So just mark it as an unexpected trap.
This allows us to kill off the cee_stuff member of struct thread_info.
Signed-off-by: David S. Miller <davem@davemloft.net>
This way we don't need to lock the TSB into the TLB.
The trick is that every TSB load/store is registered into
a special instruction patch section. The default uses
virtual addresses, and the patch instructions use physical
address load/stores.
We can't do this on all chips because only cheetah+ and later
have the physical variant of the atomic quad load.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are returning back to kernel mode, %g4 could be live
(for example, in the case where we window spill in the etrap
code). So do not change it's value if going back to kernel.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we use %g5 itself as a temporary, it can get clobbered
if we take an interrupt mid-stream and thus cause end up with
the final %g5 value too early as a result of rtrap processing.
Set %g5 at the very end, atomically, to avoid this problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
%g6 is not necessarily set to current_thread_info()
at sparc64_realfault_common. So store the fault
code and address after we invoke etrap and %g6 is
properly set up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just flip the bit off of whatever it's currently set to.
PSTATE_IE is guarenteed to be enabled when we get here.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is totally unnecessary complexity. After we take over
the trap table, we handle all PROM tlb misses fully.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the trap code was still assuming that alternate
global %g6 was hard coded with current_thread_info().
Let's just consistently flush at KERNBASE when we need
a pipeline synchronization. That's locked into the TLB
and will always work.
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSB_LOCK_BIT define is actually a special
value shifted down by 32-bits for the assembler
code macros.
In C code, this isn't what we want.
Signed-off-by: David S. Miller <davem@davemloft.net>
As the RSS grows, grow the TSB in order to reduce the likelyhood
of hash collisions and thus poor hit rates in the TSB.
This definitely needs some serious tuning.
Signed-off-by: David S. Miller <davem@davemloft.net>
This also cleans up tsb_context_switch(). The assembler
routine is now __tsb_context_switch() and the former is
an inline function that picks out the bits from the mm_struct
and passes it into the assembler code as arguments.
setup_tsb_parms() computes the locked TLB entry to map the
TSB. Later when we support using the physical address quad
load instructions of Cheetah+ and later, we'll simply use
the physical address for the TSB register value and set
the map virtual and PTE both to zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move {init_new,destroy}_context() out of line.
Do not put huge pages into the TSB, only base page size translations.
There are some clever things we could do here, but for now let's be
correct instead of fancy.
Signed-off-by: David S. Miller <davem@davemloft.net>
UltraSPARC has special sets of global registers which are switched to
for certain trap types. There is one set for MMU related traps, one
set of Interrupt Vector processing, and another set (called the
Alternate globals) for all other trap types.
For what seems like forever we've hard coded the values in some of
these trap registers. Some examples include:
1) Interrupt Vector global %g6 holds current processors interrupt
work struct where received interrupts are managed for IRQ handler
dispatch.
2) MMU global %g7 holds the base of the page tables of the currently
active address space.
3) Alternate global %g6 held the current_thread_info() value.
Such hardcoding has resulted in some serious issues in many areas.
There are some code sequences where having another register available
would help clean up the implementation. Taking traps such as
cross-calls from the OBP firmware requires some trick code sequences
wherein we have to save away and restore all of the special sets of
global registers when we enter/exit OBP.
We were also using the IMMU TSB register on SMP to hold the per-cpu
area base address, which doesn't work any longer now that we actually
use the TSB facility of the cpu.
The implementation is pretty straight forward. One tricky bit is
getting the current processor ID as that is different on different cpu
variants. We use a stub with a fancy calling convention which we
patch at boot time. The calling convention is that the stub is
branched to and the (PC - 4) to return to is in register %g1. The cpu
number is left in %g6. This stub can be invoked by using the
__GET_CPUID macro.
We use an array of per-cpu trap state to store the current thread and
physical address of the current address space's page tables. The
TRAP_LOAD_THREAD_REG loads %g6 with the current thread from this
table, it uses __GET_CPUID and also clobbers %g1.
TRAP_LOAD_IRQ_WORK is used by the interrupt vector processing to load
the current processor's IRQ software state into %g6. It also uses
__GET_CPUID and clobbers %g1.
Finally, TRAP_LOAD_PGD_PHYS loads the physical address base of the
current address space's page tables into %g7, it clobbers %g1 and uses
__GET_CPUID.
Many refinements are possible, as well as some tuning, with this stuff
in place.
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a nod from the powerpc port.
With the per-cpu caching of both the page allocator and SLAB, the
pgtable quicklist scheme becomes relatively silly and primitive.
Signed-off-by: David S. Miller <davem@davemloft.net>
We now use the TSB hardware assist features of the UltraSPARC
MMUs.
SMP is currently knowingly broken, we need to find another place
to store the per-cpu base pointers. We hid them away in the TSB
base register, and that obviously will not work any more :-)
Another known broken case is non-8KB base page size.
Also noticed that flush_tlb_all() is not referenced anywhere, only
the internal __flush_tlb_all() (local cpu only) is used by the
sparc64 port, so we can get rid of flush_tlb_all().
The kernel gets it's own 8KB TSB (swapper_tsb) and each address space
gets it's own private 8K TSB. Later we can add code to dynamically
increase the size of per-process TSB as the RSS grows. An 8KB TSB is
good enough for up to about a 4MB RSS, after which the TSB starts to
incur many capacity and conflict misses.
We even accumulate OBP translations into the kernel TSB.
Another area for refinement is large page size support. We could use
a secondary address space TSB to handle those.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "[SPARC64]: Get rid of fast IRQ feature"
moved the the code from arch/sparc64/kernel/entry.S:
lduba [%g7] ASI_PHYS_BYPASS_EC_E, %g5
or %g5, AUXIO_AUX1_FTCNT, %g5
stba %g5, [%g7] ASI_PHYS_BYPASS_EC_E
andn %g5, AUXIO_AUX1_FTCNT, %g5
stba %g5, [%g7] ASI_PHYS_BYPASS_EC_E
to arch/sparc64/kernel/irq.c:
val = readb(auxio_register);
val |= AUXIO_AUX1_FTCNT;
writeb(val, auxio_register);
val &= AUXIO_AUX1_FTCNT;
writeb(val, auxio_register);
This looks like it it missing a bitwise not, which is reintroduced
by this patch.
Due to lack of a floppy device, I could not test it, but it looks
evident.
Signed-off-by: Bernhard R Link <brlink@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must use the "a" (allocate) attribute every time we
emit an entry into the __ex_table section.
For consistency, use "a" instead of #alloc which is some
Solaris compat cruft GNU as provides on Sparc.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9ec4b1f356 made kprobes not compile
without module support, so just make that clear in the Kconfig file.
Also, since it's marked EXPERIMENTAL, make that dependency explicit too.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The change to kernel/sched.c's init code to use for_each_cpu()
requires that the cpu_possible_map be setup much earlier.
Set it up via setup_arch(), constrained to NR_CPUS, and later
constrain it to max_cpus in smp_prepare_cpus().
This fixes SMP booting on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sparc64 64 bit syscall table seems to be broken as it has
compat_sys_newfstatat in its syscall table instead of sys_newfstatat.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not enable CONFIG_LOCALVERSION_AUTO by default.
When doing kernel development it just leaves a ton
of crap around.
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, the Solaris syscall table is sized differrently,
and does not go beyond entry 255, so trim off the excess
entries.
Signed-off-by: David S. Miller <davem@davemloft.net>
This also includes by necessity _TIF_RESTORE_SIGMASK support,
which actually resulted in a lot of cleanups.
The sparc signal handling code is quite a mess and I should
clean it up some day.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a series of patches which introduce in total 13 new system calls
which take a file descriptor/filename pair instead of a single file
name. These functions, openat etc, have been discussed on numerous
occasions. They are needed to implement race-free filesystem traversal,
they are necessary to implement a virtual per-thread current working
directory (think multi-threaded backup software), etc.
We have in glibc today implementations of the interfaces which use the
/proc/self/fd magic. But this code is rather expensive. Here are some
results (similar to what Jim Meyering posted before).
The test creates a deep directory hierarchy on a tmpfs filesystem. Then
rm -fr is used to remove all directories. Without syscall support I get
this:
real 0m31.921s
user 0m0.688s
sys 0m31.234s
With syscall support the results are much better:
real 0m20.699s
user 0m0.536s
sys 0m20.149s
The interfaces are for obvious reasons currently not much used. But they'll
be used. coreutils (and Jeff's posixutils) are already using them.
Furthermore, code like ftw/fts in libc (maybe even glob) will also start using
them. I expect a patch to make follow soon. Every program which is walking
the filesystem tree will benefit.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Eddie C. Dost <ecd@brainaid.de>
I have the following patch for serial console over the RSC
(remote system controller) on my E250 machine. It basically adds
support for input-device=rsc and output-device=rsc from OBP, and
allows 115200,8,n,1,- serial mode setting.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Ensure a consistent value is read from the STICK register by ensuring
that both high and low are read without high changing due to a roll
over of the low register.
Various Debian/SPARC users (myself include) have noticed problems with
Hummingbird based systems. The symptoms are that the system time is
seen to jump forward 3 days, 6 hours, 11 minutes give or take a few
seconds. In many cases the system then hangs some time afterwards.
I've spotted a race condition in the code to read the STICK register.
I could not work out why 3d, 6h, 11m is important but guess that it is
due to the 2^32 jump of STICK (forwards on one read and then the next
read will seem to be backwards) during a timer interrupt. I'm guessing
that a change of -2^32 will get converted to a large unsigned
increment after the arithmetic manipulation between STICK,
nanoseconds, jiffies etc.
I did a test where I modified __hbird_read_stick to artificially
inject rollover faults forcefully every few seconds. With this I saw
the clock jump over 6 times in 12 hours compared to once every month
or so.
Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a window where a probe gets removed right after the probe is hit
on some different cpu. In this case probe handlers can't find a matching
probe instance related to break address. In this case we need to read the
original instruction at break address to see if that is not a break/int3
instruction and recover safely.
Previous code had a bug where we were not checking for the above race in
case of reentrant probes and the below patch fixes this race.
Tested on IA64, Powerpc, x86_64.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo in the dependencies of HUGETLB_PAGE_SIZE_64K.
It might be more logical to rename the HUGETLB_PAGE_SIZE_*K
dependencies to HUGETLB_PAGE_SIZE_*KB, but let's fix this bug first.
This bug was reported by Jean-Luc Leger <reiga@dspnet.fr.eu.org>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently arch_remove_kprobes() is only implemented/required for x86_64 and
powerpc. All other architecture like IA64, i386 and sparc64 implementes a
dummy function which is being called from arch independent kprobes.c file.
This patch removes the dummy functions and replaces it with
#define arch_remove_kprobe(p, s) do { } while(0)
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since Kprobes runtime exception handlers is now lock free as this code path is
now using RCU to walk through the list, there is no need for the
register/unregister{_kprobe} to use spin_{lock/unlock}_isr{save/restore}. The
serialization during registration/unregistration is now possible using just a
mutex.
In the above process, this patch also fixes a minor memory leak for x86_64 and
powerpc.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that all these entries in the arch ioctl32.c files are gone [1], we can
build fs/compat_ioctl.c as a normal object and kill tons of cruft. We need a
special do_ioctl32_pointer handler for s390 so the compat_ptr call is done.
This is not needed but harmless on all other architectures. Also remove some
superflous includes in fs/compat_ioctl.c
Tested on ppc64.
[1] parisc still had it's PPP handler left, which is not fully correct
for ppp and besides that ppp uses the generic SIOCPRIV ioctl so it'd
kick in for all netdevice users. We can introduce a proper handler
in one of the next patch series by adding a compat_ioctl method to
struct net_device but for now let's just kill it - parisc doesn't
compile in mainline anyway and I don't want this to block this
patchset.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment in compat.c is wrong, every architecture provides a
get_compat_sigevent() for the IPC compat code already.
This basically moves the x86_64 version to common code and removes all the
others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Adrian Bunk <bunk@stusta.de>
- create one common dump_thread() prototype in kernel.h
- dump_thread() is only used in fs/binfmt_aout.c and can therefore be
removed on all architectures where CONFIG_BINFMT_AOUT is not
available
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't clobber register %l0 while checking TI_SYS_NOERROR value in
syscall return path. This bug was introduced by:
db7d9a4eb7
Problem narrowed down by Luis F. Ortiz and Richard Mortimer.
I tried using %l2 as suggested by Luis and that works for me.
Looking at the code I wonder if it makes sense to simplify the code
a little bit. The following works for me but I'm not sure how to
exercise the "NOERROR" codepath.
Signed-off-by: David S. Miller <davem@davemloft.net>
Configurable 16-bit UID and friends support
This allows turning off the legacy 16 bit UID interfaces on embedded platforms.
text data bss dec hex filename
3330172 529036 190556 4049764 3dcb64 vmlinux-baseline
3328268 529040 190556 4047864 3dc3f8 vmlinux
From: Adrian Bunk <bunk@stusta.de>
UID16 was accidentially disabled for !EMBEDDED.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ptrace_get_task_struct() helper that I added as part of the ptrace
consolidation is useful in variety of places that currently opencode it.
Switch them to the common helpers.
Add a ptrace_traceme() helper that needs to be explicitly called, and simplify
the ptrace_get_task_struct() interface. We don't need the request argument
now, and we return the task_struct directly, using ERR_PTR() for error
returns. It's a bit more code in the callers, but we have two sane routines
that do one thing well now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's definition is wrong (-1 means "no limit" not 999),
only the Sparc SunOS/Solaris compat code uses it, so
let's just kill it off completely from limits.h and
all referencing code.
Noticed by Ulrich Drepper.
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a Kconfig symbol SPARC that is defined on both the sparc and
sparc64 architectures.
This symbol makes some dependencies more readable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was a stupid workaround for the "static inline" vs.
"extern inline" issues of long ago, and it is what causes
schedule() to be inlined like crazy into kernel/sched.c
when -Os is specified.
MIPS and S390 should probably do the same.
Now CC_OPTIMIZE_FOR_SIZE can be safely used on sparc64
once more.
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple probes are registered at the same address and if due to some
recursion (probe getting triggered within a probe handler), we skip calling
pre_handlers and just increment nmissed field.
The below patch make sure it walks the list for multiple probes case.
Without the below patch we get incorrect results of nmissed count for
multiple probe case.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Increment the PFN field of the PTE so that the tests
on vm_pfn in mm/memory.c match up. The TLB ignores these
lower bits for larger page sizes, so it's OK to set things
like this.
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier I unifdefed PageCompound, so that snd_pcm_mmap_control_nopage and
others can give out a 0-order component of a higher-order page, which won't
be mistakenly freed when zap_pte_range unmaps it. But many Bad page states
reported a PG_reserved was freed after all: I had missed that we need to
say __GFP_COMP to get compound page behaviour.
Some of these higher-order pages are allocated by snd_malloc_pages, some by
snd_malloc_dev_pages; or if SBUS, by sbus_alloc_consistent - but that has
no gfp arg, so add __GFP_COMP into its sparc32/64 implementations.
I'm still rather puzzled that DRM seems not to need a similar change.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Although we tend to associate VM_RESERVED with remap_pfn_range, quite a few
drivers set VM_RESERVED on areas which are then populated by nopage. The
PageReserved removal in 2.6.15-rc1 changed VM_RESERVED not to free pages in
zap_pte_range, without changing those drivers not to set it: so their pages
just leak away.
Let's not change miscellaneous drivers now: introduce VM_UNPAGED at the core,
to flag the special areas where the ptes may have no struct page, or if they
have then it's not to be touched. Replace most instances of VM_RESERVED in
core mm by VM_UNPAGED. Force it on in remap_pfn_range, and the sparc and
sparc64 io_remap_pfn_range.
Revert addition of VM_RESERVED to powerpc vdso, it's not needed there. Is it
needed anywhere? It still governs the mm->reserved_vm statistic, and special
vmas not to be merged, and areas not to be core dumped; but could probably be
eliminated later (the drivers are probably specifying it because in 2.4 it
kept swapout off the vma, but in 2.6 we work from the LRU, which these pages
don't get on).
Use the VM_SHM slot for VM_UNPAGED, and define VM_SHM to 0: it serves no
purpose whatsoever, and should be removed from drivers when we clean up.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new function, sbusfb_compat_ioctl() to
drivers/video/sbuslib.c and uses it as compat_ioctl in all sbus fb
drivers
This remove the last per-arch compat ioctl bits in
arch/sparc64/kernel/ioctl32.c so it would be nice if people could test
if this actually copiles and works and if yes apply it :)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed by Tom 'spot' Callaway.
Even on uniprocessor we always reported the number of physical
cpus in the system via /proc/cpuinfo. But when this got changed
to use num_possible_cpus() it always reads as "1" on uniprocessor.
This change was unintentional.
So scan the firmware device tree and count the number of cpu
nodes, and report that, as we always did.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove a
duplicate of ARRAY_SIZE which is never used anyways.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some architectures define and use this type in their compat_ioctl code, but
all of them can easily use the identical ioctl_trans_handler_t type that is
defined in common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update comment on get_user_insn to the more general "pte lock", which may
or may not be the page_table_lock. Note vmtruncate handled like kswapd.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/drm/ now implements proper ->compat_ioctl methods, so this isn't
needed anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
all ioctls are 32bit compat clean, so the driver can use ->compat_ioctl
and ->unlocked_ioctl easily.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
implement a compat_ioctl handle in the driver instead of having table
entries in sparc64 ioctl32.c (I plan to get rid of the arch ioctl32.c
file eventually)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
all the ioctls in the driver are 32bit compat clean and don't need BKL,
so we can switch it to ->unlocked_ioctl and ->compat_ioctl trivially.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Would you mind applying the following patch that kills those two + the
m68k and Documentation/ references?
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
all these are handled by fs/compat_ioctls.c already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't know if we ever implemented this, but the only user in any 2.6
tree are the compat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old keyboard driver is gone in 2.6, so the only user left are the
compat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old sound drivers are gone in 2.6, so the only user left are the
compat ioctls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
this inline routine in arch/sparc64/kernel/ioctl32.c is completely
unused and superceeded by compat_alloc_user_space()
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It only serves to generate false-positive buildcheck warnings.
Just set it initially to tick_operations which uses the v9
%tick register which every sparc64 processor has.
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't needed any longer, as noted by Hugh Dickins.
We still need the flush routines, due to the one remaining
call site in hugetlb_prefault_arch_hook(). That can be
eliminated at some later point, however.
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc64 is unique among architectures in taking the page_table_lock in
its context switch (well, cris does too, but erroneously, and it's not
yet SMP anyway).
This seems to be a private affair between switch_mm and activate_mm,
using page_table_lock as a per-mm lock, without any relation to its uses
elsewhere. That's fine, but comment it as such; and unlock sooner in
switch_mm, more like in activate_mm (preemption is disabled here).
There is a block of "if (0)"ed code in smp_flush_tlb_pending which would
have liked to rely on the page_table_lock, in switch_mm and elsewhere;
but its comment explains how dup_mmap's flush_tlb_mm defeated it. And
though that could have been changed at any time over the past few years,
now the chance vanishes as we push the page_table_lock downwards, and
perhaps split it per page table page. Just delete that block of code.
Which leaves the mysterious spin_unlock_wait(&oldmm->page_table_lock)
in kernel/fork.c copy_mm. Textual analysis (supported by Nick Piggin)
suggests that the comment was written by DaveM, and that it relates to
the defeated approach in the sparc64 smp_flush_tlb_pending. Just delete
this block too.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc64 prom_callback and new_setup_frame32 each operates on a user page
table without holding lock, and no doubt they've good reason. But I'd
feel more confident if they were to do a "pte = *ptep" and then operate
on pte, rather than re-evaluating *ptep.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the arch/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in arch/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reorganize the preempt_disable/enable calls to eliminate the extra preempt
depth. Changes based on Paul McKenney's review suggestions for the kprobes
RCU changeset.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the arch kprobes infrastructure to take advantage of the locking
changes introduced by usage of RCU for synchronization. All handlers are now
run without any locks held, so they have to be re-entrant or provide their own
synchronization.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David S. Miller