This patch reduces delay time when configuring video setting,
which is helpful to reduce wakeup time during resume.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The sw reset should be called prioir to enabling sw defined function,
according to datasheet.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Rework the interrupt handler so the RX_DONE, FIFO_EMPTY interrupts are
properly detected. This prevents missing the interrupts when there are
other bits set in the INTSRC register than just RX_DONE and FIFO_EMPTY.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Make sure all resources are initialized before interrupt handler is
registered. Pass full platform device name to request_irq() so it
can be distinguished which device has requested an interrupt in cases
there are multiple instances in the system.
Also enable voltage regulators regardless of they have been enabled
by bootloader or not, to make sure other drivers using same regulators
don't disable them unexpectedly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Use proper PM ops from struct dev_pm_ops rather than the deprecated ones.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Remove unnecessary headers from the file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
When exynos_mipi_update_cfg() is called, mipi dsi registers were become
sw reset. So, It needs to enable interrupt again.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The exynos_mipi_dsi_set_main_disp_[hv]porch() functions take front and
back porch arguments in that order. This maps to the fb_videomode
right/lower_margin and left/upper_margin respectively. Fix the caller
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
This patch adds analog and pll control setting. This control setting
is used for DP TX PHY block to set the values as below. It is beneficial
to improve analog characteristics.
- TX terminal registor is 50 Ohm.
- Reference clock of PHY is 24 MHz.
- Power source for TX digital logic is 1.0625 V.
- Power source for internal clock driver is 1.0625 V.
- PLL VCO range setting is 600 uA.
- Power down ring osc is turned off.
- AUX terminal resistor is 50 Ohm.
- AUX channel current is 8 mA and multiplied by 2.
- TX channel output amplitude is 400 mV.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The char pointer for adjust_request variable is replaced with char array
to fix possible null pointer dereference when clock recovery is failed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
DP PLL Lock status should be checked in order to prevent unlocked PLL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Samsung EXYNOS SoC such Exynos5 has DP controller and embedded DP
panel can be used. This patch supports DP driver based on Samsung
EXYNOS SoC chip.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
An moled panel driver based MIPI DSI interface. S6E8AX0 means it may
includes many other ldi controllers, for example, S6E8AA0, S6E8AB0, and so
on.
This patch can be modified depending on each panel properites. For
example, second parameter of panel condition register can be changed
depending on ldi controller or amoled type.
[akpm@linux-foundation.org: fix Kconfig syntax error]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Samsung S5PC210 and EXYNOS SoC platform has MIPI-DSI controller and
MIPI-DSI based LCD Panel could be used with it. This patch supports
MIPI-DSI driver based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
machine code and LCD panel driver specific function registered to
mipi_dsim_ddi structure at lcd panel init function called system init. In
the MIPI-DSI driver, find lcd panel driver by using registered lcd panel
name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Jingoo Han