Allow platform probe to register platform kcontrols and DAPM just like
the CODEC probe().
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow platform driver widgets to perform any IO required for DAPM.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for Dynamic PCM (AKA DSP) support.
Allow platform drivers to register kcontrols.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now we have supply widgets there's no need to open code the handling of
the ACTIVE bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In preparation for ASoC Dynamic PCM (AKA DSP) support.
Allow platform driver to perform IO. Intended for platform DAPM.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This delay is very conservative.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
The clock needed by the I2S driver is associated with the I2S device name
in the standard fashion. Hence, use clk_get(dev) instead of clk_get_sys(clk_name).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The I2S controller needs a clock to respond to register writes. Without
this, register writes will at worst hang the CPU. In practice, I've only
observed writes being dropped.
Luckily, the dropped register writes historically had no effect:
TEGRA_I2S_TIMING: The value we wrote was the reset default.
TEGRA_I2S_FIFO_SCR: The default was for the FIFOs to request more data
when one slot was empty. The requested value was for the FIFOs to request
when four slots were empty. The DMA controller in the mainline kernel is
configured to burst a single entry at a time into the FIFO, hence there
was no issue. The only negative effect was on bus efficiency losses due
to an increased number of arbitration attempts.
However, in various non-upstream changes, the DMA controller now bursts
four entries at a time into the FIFO. If there is only space for one
entry, the data is simply dropped. In practice, this resulted in 3/4 of
samples being dropped, and playback at 4x the expected rate and pitch.
By fixing the clocking issue, this is solved.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for ASoC dynamic PCM support (AKA ASoC DSP)
Platform will also support DAPM so separate out the probe function
to simplify the code (just like the codec probe).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
More for neatness than any actual performance improvement.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
It was consistently wrong for everything except WM8993 so should be no
functional change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.comm>
The Blackfin DMA controller can report one frame beyond the end of the
buffer in the wraparound case but ALSA requires that the pointer always
be in the buffer. Do the wraparound to handle this. A similar bug is
likely to apply to the other Blackfin PCM drivers but the code is less
obvious to inspection and I don't have a user to test.
Reported-by: Kieran O'Leary <Kieran.O'Leary@wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Add a machine driver to support the EVAL-ADAV801 and EVAL-ADAV803 boards
connected to a Analog Devices BF5XX evaluation board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add idma related register definitions to support idma.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I2S registers can be used for control idma.
Previously, register is defined in i2s.c.
For sharing the registers, It is moved to i2s-regs.h
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add WM8994 PCM machine driver to support PCM audio
on SMDKV310, SMDKC210 boards.
Playback and Capture supports 8kHz sampling rates.
and It is tested on SMDKV310, SMDKC210.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't rely on the codec's channels_min information to decide wheter or
not allocate a substream's DMA buffer. Rather check if the substream
itself was allocated previously.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
SND_MXC_SOC_SSI looks to be unused, so kill it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8918 is register compatible with the WM8904 with a subset of the
functionality. Add the device ID, a subsequent patch will ensure that only
the relevant functionality is exported to userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Some devices do not support manual updates of the DC servo.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
[zonque@gmail.com: transform to new ASoC structure]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
[zonque@gmail.com: transform to new ASoC structure]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The base hardware revision of the Maxim 98095 part is 0x40; the code
which outputs the revision of the hardware has been updated to
properly use uppercase alphabetic values for the revision numbers.
Also, the use of a constant for the length 'max98095_dai' has been
replaced with ARRAY_SIZE().
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Acked-by: Peter Hsiang <peter.hsiang@maxim-ic.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
"ret" is supposed to be signed here. The current code will only
return -EIO on error, instead of a more appropriate error code such
as -EAGAIN etc.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously we were using the DAPM context rather than a widget as the
argument for update_bits() so we didn't need to care that our list walk
of widgets left us one beyond the end of the list. Now we're using them
for the register update we need to make sure we're pointing at an actual
widget not the list_head.
Fix originally suggested by Liam on IM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The Sigma code is in drivers/firmware which is only included on a very
small subset of architectures and so ends up breaking the build on
others. There's a pending patch to make the directory build as standard
but it's not merged yet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This board has hardware switches for selecting SPI or I2C, so don't
require I2C for this driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use less specific names for suspend/resume to match the probe/remove funcs
where these are now used.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The codec name should not have a "-codec" suffix since this is not part of
a MFD. This was incorrectly changed during the multi-component updated.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The only thing the init func does is register a spi driver, so if that
fails, we return the value back up to the caller who will display an
error message for us. So drop the redundant checking/message.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver to support the ADAU1701 SigmaDSP processors on
Analog Devices BF5XX evaluation boards.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Analog Devices ADAU1701 SigmaDSP.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This time with soc_widget_update_bits reflecting recent soc_update_bits changes.
Currently widget IO is tightly coupled to the CODEC drivers. Future platform DSP
devices have mixer components that can alter power usage and hence require full
DAPM support.
This provides a generic widget IO operation wrapper in preparation for
future patches that implement platform driver DAPM.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will be removed in -next so let's drop it from mainline as soon as
we can in order to minimise surprises.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to facilitate merging with the register map I/O replace the use
of control_data for the bulk writes with direct lookup of the client data
from the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Normally DAPM will power up any connected audio path. This is not ideal
for sidetone paths as with sidetone paths the audio path is not wanted in
itself, it is only desired if the two paths it provides a sidetone between
are both active. If the sidetone path causes a power up then it can be
hard to minimise pops as we first power up either the sidetone or the main
output path and then power the other, with the second power up potentially
introducing a DC offset.
Address this by introducing the concept of a weak path. If a path is marked
as weak then DAPM will ignore that path when walking the graph, though all
the relevant controls are still available to the application layer to allow
these paths to be configured.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
For clarity and to help ongoing refactoring in this area create a new file
to contain the physical I/O functions, separating them out from the cache
operations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We've got a whole bunch of functions which just call straight through to
do_hw_read(). Simplify this situation by removing them and using hw_read()
directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
