Unfortunelly (my fault) the kernel thread that now handles IR processing
has classical races in regard to wakeup and stop.
This patch hopefully closes them all.
Tested with module reload running in a loop, while receiver is blasted
with IR data for 10 minutes.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The rc map table were corrected thanks to Giorgio input and tests.
Reported-by: Giorgio Vazzana <mywing81@gmail.com>
Tested-by: Giorgio Vazzana <mywing81@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for tuning with PSK8 modulation, pilot and rolloff
with the S2 versions of firedtv.
Signed-off-by: Tommy Jonsson <quazzie2@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (trivial simplification)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is possible that, while ir_unregister_class() is handling, some
application could try to access the sysfs nodes, causing an OOPS.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is an integer overflow here because 0x03000000 * 1000 is too large
for 31 bits.
rawir.duration should be in terms of nsecs.
IR_MAX_DURATION and 0x03000000 are already in terms of nsecs.
STREAMZAP_TIMEOUT and STREAMZAP_RESOLUTION are 255 and 256 respectively
and are in terms of usecs.
The original code had a deadline of 1.005 seconds and the new code has a
deadline of .065 seconds.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed out (and tested) by Joris van Rantwijk, we do actually need
to wire up .compat_ioctl for 32-bit lirc userspace to work with 64-bit
lirc kernelspace. Do it. And add a check to make sure we get a valid
irctl in the ioctl handler.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
>From Joris van Rantwijk <jorispubl@xs4all.nl>:
I tested lirc_serial and found that it works fine.
Except the LIRC ioctls do not work in my 64-bit-kernel/32-bit-user
setup. I added compat_ioctl entries in the drivers to fix this.
While doing so, I noticed inconsistencies in the argument type of
the LIRC ioctls. All ioctls are declared in lirc.h as having argument
type __u32, however there are a few places where the driver calls
get_user/put_user with an unsigned long argument.
The patch below changes lirc_dev and lirc_serial to use __u32 for all
ioctl arguments, and adds compat_ioctl entries.
It should probably also be done in the other low-level drivers,
but I don't have hardware to test those.
I've dropped the .compat_ioctl addition from Joris' original patch,
as I swear the non-compat definition should now work for both 32-bit
and 64-bit userspace. Technically, I think we still need/want a
in getting a reply to you).
Reported-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per discussion with Andy Walls on irc, rx fifo overruns are not all that
uncommon on a busy system, and the initial posting of the nuvoton-cir
driver doesn't handle them well enough. With this addition, we'll drain
the hw fifo, attempt to process any ir pulse trains completed with that
flush, then we'll issue a hw rx fifo clear and reset the raw ir sample
kfifo and start over collecting raw ir data.
Also slightly refactors the cir interrupt enabling so that we always get
consistent flags set and only have to modify them in one place, should
they need to be altered.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new ir-core pnp driver for the Nuvoton w836x7hg integrated CIR
function. The chip is found on at least the ASRock ION 330HT boxes and
apparently, on a number of Intel DP55-series motherboards:
http://www.asrock.com/nettop/overview.asp?Model=ION%20330HThttp://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=17685&lang=eng
This driver was made possible by a hardware donation from Nuvoton, along
with sample code (in the form of an lirc driver) and datasheet, so huge
thanks to them for supporting this effort. Note that this driver
constitutes a massive rewrite, porting from the lirc interfaces to the
ir-core interfaces, and restructuring the driver to look more like Maxim
Levitsky's ene_ir driver (as well as generally making it look more like
kernel code).
There's some work left to be done on this driver, to fully support the
range of functionality possible, but receive and IR power-on/wake are
both functional (may require setting wake key under another OS atm). The
hardware I've got (one of the ASRock boxes) only supports RX, so TX is
completely untested as of yet. Certain RX parameters, like sample
resolution and RX IRQ sample length trigger level could possibly stand
to be made tweakable via modparams or sysfs nodes, but the current
values work well enough for me w/an MCE RC6A remote.
The original lirc driver carried support for the Windows MCE IR
keyboard/mouse device, which I plan to add back generically, in a way
that should be usable by any raw IR receiver (or at least by this driver
and the mceusb driver).
Suspend and resume have also been tested, the power button on my remote
can be used to wake the machine, and CIR functionality resumes just
fine. Module unload/reload has also been tested, though not extensively
or repetitively. Also tested to work with the lirc bridge plugin for
userspace decoding.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new control mechanism uses dynamic control values in the subdriver
descriptor. It simplifies standard control handling.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Take the ctrl_mutex mutex before touching control information in those
functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
XU control information is supposed to be entirely discoverable using
standard UVC queries. As some devices report bogus information (such as
reporting a read-only control as being read-write), add a fixup table
for XU controls.
This table can also be used to selectively disable requests supposed to
be supported by all XU controls (GET_MIN, GET_MAX, GET_DEF, GET_RES) but
not correctly (or at all) supported by the device.
The table currently disables GET_CUR on the Logitech motor control XU
pan/tilt controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
XU controls initialization requires querying the device for control
information. As some buggy UVC devices will crash when queried
repeatedly in a tight loop, delay XU controls initialization until first
use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that control information structures are not shared between control
instances, embed a uvc_control_info instance inside the uvc_control
structure instead of storing a pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the sysadmin requirements for UVCIOC_CTRL_MAP (and the stub
implementation of UVCIOC_CTRL_ADD). This requirement no longer makes sense with
the new XU control access mechanisms since XU controls can be accessed without
adding control mappings first.
A maximum number (currently 1024) of control mappings per device is enforced to
avoid excess memory consumption caused by careless user space applications.
Signed-off-by: Martin Rubli <martin_rubli@logitech.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devices advertise XU controls using a bitmask, in which each bit
corresponds to a control. The control selector, used to query the
control, isn't available in the USB descriptors.
All known UVC devices use control selectors equal to the control bit
index plus one. Hardcode that relationship in the driver, making the
UVCIOC_CTRL_ADD ioctl obsolete. All necessary information about XU
controls can be obtained by the driver at enumeration time.
The UVCIOC_CTRL_ADD ioctl is still supported for compatibility reasons,
but now always returns -EEXIST.
Finally, control mappings are now on a per-device basis and no longer
global.
As this changes the userspace interface, bump the driver version number
to 1.0.0 (it was about time).
Signed-off-by: Martin Rubli <martin_rubli@logitech.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase the sequence number of the v4l2_buffer structure regardless of
any buffer states, so that discontinuous sequence numbers allow
applications to detect lost video frames.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bandwidth estimate computed with the FIX_BANDIWDTH quirk is too low
for many cameras. Don't use maximum packet sizes lower than 1024 bytes
to try and work around the problem. According to measurements done on
two different camera models, the value is high enough to get most
resolutions working while not preventing two simultaneous VGA streams at
15 fps.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of printing the query hex value in error messages, print its
name to make the messages more readable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
They're not modified by the function, make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Hercules Dualpix Exchange (06f8:3005) camera expose an absolute zoom
that is not implemented. Blacklist it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't hold the lock before unregistering the device, since when the
device is unregistered the datastruct containing the lock may be freed
(if the refcount went to 0).
Also fixed the framework documentation that erroneously suggested the
wrong locking order as well.
Reported-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use new RC core instead of old legacy RC implementation.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Imported from af9015.h. Initial keytable was from
Jose Alberto Reguero <jareguero@telefonica.net> and
Felipe Morales Moreno <felipe.morales.moreno@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Digittrade DVB-T USB Stick remote controller.
Imported from af9015.h. Initial keytable was from Alain Kalker <miki@dds.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Imported from af9015.h.
Initial keytable was from Marc Schneider <macke@macke.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MSI DIGIVOX mini III remote controller. Uses NEC extended 0x61d6.
This remote seems to be same as rc-kworld-315u.c. Anyhow, add new remote
since rc-kworld-315u.c lacks NEC extended address byte.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Variable is don't care in that case. No need to set value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AVerTV Red HD+ (A850T) is basically the same as the existing
AVerTV Volar Black HD (A850), but is specific to the french market.
The A850T identifies itself as a A850, but has its own PID. It even
suffers from the same EEPROM deficiencies.
This is based off a collection of information gathered from the
french support forums for Ubuntu, which I tried to properly format
into this patch:
http://forum.ubuntu-fr.org/viewtopic.php?pid=3322825
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@anciens.enib.fr>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Demod + tuner specific RF AGC and IF AGC limit values are read from demod
memory in every signal strength query. Cache those to reduce I2C traffic.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Precalculate coefficients register values. This reduces text size around 300 bytes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of doing its own lock, use core-assisted one. As a bonus, it
will do the proper unlock during queue wait events. This fixes a
long-standing bug where softwares like tvtime would hang if you try to
use cx231xx-alsa.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This file came originally from cx23885 driver. Some functions aren't
used. Now that they are declared as static, we have those errors:
drivers/media/video/cx231xx/cx231xx-417.c:615: warning: ‘mc417_gpio_set’ defined but not used
drivers/media/video/cx231xx/cx231xx-417.c:625: warning: ‘mc417_gpio_clear’ defined but not used
drivers/media/video/cx231xx/cx231xx-417.c:635: warning: ‘mc417_gpio_enable’ defined but not used
As they're not used, just remove them. If needed, they can be restored from
the git logs or from the cx23885 driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx23885/built-in.o: In function `mc417_memory_write':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:482: multiple definition of `mc417_memory_write'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:477: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_gpio_set':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:636: multiple definition of `mc417_gpio_set'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:615: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_gpio_enable':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:656: multiple definition of `mc417_gpio_enable'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:635: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_memory_read':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:546: multiple definition of `mc417_memory_read'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:541: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_gpio_clear':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:646: multiple definition of `mc417_gpio_clear'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:625: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_register_read':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:388: multiple definition of `mc417_register_read'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:401: first defined here
drivers/media/video/cx23885/built-in.o: In function `mc417_register_write':
/home/v4l/v4l/patchwork/drivers/media/video/cx23885/cx23885-417.c:324: multiple definition of `mc417_register_write'
drivers/media/video/cx231xx/built-in.o:/home/v4l/v4l/patchwork/drivers/media/video/cx231xx/cx231xx-417.c:343: first defined here
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gcc didn't like to have i++ inside a complex operation:
drivers/media/video/cx231xx/cx231xx-417.c: In function ‘cx231xx_load_firmware’:
drivers/media/video/cx231xx/cx231xx-417.c:1059: warning: operation on ‘i’ may be undefined
drivers/media/video/cx231xx/cx231xx-417.c:1061: warning: operation on ‘i’ may be undefined
drivers/media/video/cx231xx/cx231xx-417.c:1063: warning: operation on ‘i’ may be undefined
Btw, I agree with gcc, as we're using i and i++ at the same operation and,
depending on how optimization may occur, it may produce a wrong code.
While here, fix CodingStyle issues on the changed code.
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patches received from the vendor contained a lot of CodingStyle
issues. Cleans the style issues reported by checkpatch.pl on
those drivers.
It is better to do such style fixes when merging a big set of
changes than latter. Of course, the better is to receive patches
already cleaned ;)
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By default, tda18271 tries to optimize I2C bus by updating all registers
at the same time. Unfortunately, some devices doesn't support it.
The current logic has a problem when small_i2c is equal to 8, since there
are some transfers using 11 + 1 bytes.
Fix the problem by enforcing the max size at the right place, and allows
reducing it to max = 3 + 1.
Acked-by: Michael Krufky <mkrufky@kernellabs.com>
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improves the logic, for it to be clearer and to avoid having
board-dependent config there.
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver has a field to indicate what bus is used by tuner and
by demod. However, this field were never used. On Pixelview,
it uses I2C 2 for tuner, instead of I2C 1.
drivers/media/video/cx231xx/cx231xx-cards.c
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx231xx/cx231xx-avcore.c:1608: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘long unsigned int’
drivers/media/video/cx231xx/cx231xx-417.c:1047: warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘size_t’
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adjust the vblank and vactive counts so that they don't throw an error in
cx25840's set_std call (we did an equivalent change for NTSC when we got the
scaler working).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx231xx_do_mode_ctrl_overrides() function was not touching the vactive line
count for PAL/SECAM modes, which in some use cases results in it being left in
the chip default state of 480 (NTSC).
Explicitly set the values, as is already done for NTSC.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some indentation problems and remove an "if (1)" from the Colibri setup
function.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx231xx_set_Colibri_For_LowIF() function is only ever called if the tuner
has a DIF (see vidioc_s_frequency() in cx231xx-video.c). Hence, we do not
need to do a board specific check in this function.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was deciding whether a DIF was present based on the board
profile. However, this is just another thing for someone to get wrong when
adding new boards. Make the decision based on the tuner instead, so that a
developer adding new boards only needs to specify which tuner the device has.
Of course, the first time somebody adds a board with a tuner other than xc5000
or tda18271, he/she will need to add another line for that tuner. But we
provide a friendly message in dmesg to let them know that.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nobody is ever going to implement an i2c based IR controller on a bridge that
has an onboard universal IR receiver. This stuff was all copied from em28xx,
which has old enough versions of the chip that some didn't have onboard IR.
Remove the stubs related to i2c based IR (keeping the cx231xx-input code).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move a printk() message which refers to enabling the cx23417 so that it only
shows up on a board that has the cx23417.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video grabber reference design (Veyron) does not have a tuner input, so
do not have it defined in the board profile.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend the board profile structure to allow configuration of the output mode.
Right now they are all doing VIP 1.1 format, but we have a board that needs
ITU656 format (which hasn't been checked in yet).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add initial support for the Hauppauge USBLive 2 (2040:c200). Note that I
had to copy a bunch of the case statements used for the Conexant video grabber
reference design (which also doesn't have a tuner). This will likely need to
be refactored out into the board profile.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner is on i2c port 3 just like all the reference designs. Having it
improperly set to port #1 causes the tuner initialization to fail when enabling
the device.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If switching to a tuner input, reset the standard and tune to the last known
frequency. We need to do this in particular for this bridge since the tuner
gets powered down when captuing on the composite or s-video inputs.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a hack which was jammed into s_input to force the device into bulk mode
at runtime (an abuse of the API). If this sort of functionality is actually
needed (aside from the existing "transfer_mode" modprobe variable), a patch
can be submitted which makes use of a private control.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Exeter hardware design does not use GPIOs to manage whether its in
digital mode or analog mode, but we need to setup the power control properly.
For that board, setup power control and remove the mux select call. It is
highly likely that this change could be used by other boards as well, which
would make power management cleaner (fixing known issues transitioning between
analog and digital mode).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
You cannot call the video_mux routine from within the isoc setup, because that
code is shared with the digital isoc handler. This was causing the GPIOs and
power control to be put into the wrong state when starting up digital mode.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to clear out the field before setting individual bits, or else we end
up with a union of whatever was there and what we are trying to set. For
example, switching to digital mode ends up being 0x30 instead of 0x10 if we
were previously in analog tv mode.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the responsibility for setting up the horizontal and vertical scalers
entirely to the cx25840 driver. The cx231xx-avcore was actually programming
garbage into the HSCALE_CTRL and VSCALE_CTRL registers (because of differences
in how the em28xx driver worked, which the cx231xx driver was derived from).
The net effect is that the scaler now works properly (tested with both PAL
and NTSC under mplayer and tvtime).
This patch also gets rid of cx25840 errors showing up in dmesg which say
"720x480 is not a valid size" (since we now properly setup the size of the
active video area).
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the log level from info to debug for some log events that occur
frequently and should never need to be seen in normal operation.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need for a switch statement here. Use the contents of the board
profile to dictate the tuner driver and i2c address. Eventually if a board
ever comes around which has a different i2c bus than #1, well that should be a
field in the board profile as well.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was sending one videobuf per field (despite having specified
V4L2_FIELD_SEQ_TB during setup). As a result, application which used the
read() interface would work, except they would sometimes have the fields
reversed (depending on the luck of which field the device was on when the
application started VBI capture). The net effect was that CC decoding would
only work about 50% of the time.
Restructure the VBI code a bit so that works like all the other drivers, such
that both fields are delivered in a single videobuf buffer, which ensures that
they are always received in a predictable order.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VBI sampling rate and offset were incorrectly specified, which resulted in
CC data not being rendered under zvbi or tvtime.
Set the fields correctly.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change a %x to a %p since the variable is a pointer
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Run Lindent and fix a few spacing issues.
This patch makes no functional change to the driver.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Configure the tda18271 to use a smaller transaction size by default, which
works around some sort of i2c bug in the Polaris driver (which needs to be
debugged).
This should be safe for other boards (being in tuner-core means it will be
enabled by default), although testing needs to be done.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix case where analog calls come in while the DVB side of the board is still
initializing. This patch is actually just an exact port of the same patch
made by Mauro to em28xx in hg rev 14762.
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for various Hauppauge EXETER designs.
Note by DJH: fixed a few minor 'make checkpatch' warnings before commit.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a new driver for the s5h1432
Signed-off-by: Palash Bandyopadhyay <palash.bandyopadhyay@conexant.com>
Signed-off-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows GStreamer to pick appropriate framerates and resolutions
based on desired capture parameters.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch, which basically reverts 6d77444ac, fixes an occasional
on-boot or on-capture hang on the XO-1 laptop.
It seems like the cafe hardware is flakier than we thought and that in
some cases, the commands get executed but are never reported as completed
(even if we substantially increase the delays before reading registers).
Reintroduce the 1-second CAFE_SMBUS_TIMEOUT to catch and avoid this
strange hardware bug.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed by Laurent:
I think min_t(size_t, PAGE_SIZE, size) is the preferred way.
Thanks-to: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some symbols at saa7134-input that are used on saa7134
and vice-versa. Due to that, module install fails.
So, partially revert commit 9f495cf7d691c99bf7bdcec9f35fcfdad2cf9ae9.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/videobuf-dma-sg.c: In function ‘videobuf_pages_to_sg’:
drivers/media/video/videobuf-dma-sg.c:119: warning: comparison of distinct pointer types lacks a cast
drivers/media/video/videobuf-dma-sg.c:120: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver sn9c102 does not know about the sensor mi0360b.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'end of image' block may be splitted between two ISOC packets.
This case was not tested, so, some images could be lost and concatenated
to previous one(s), raising 'frame overflow' errors.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Call to i2c_put_adapter was missing in radio_si4713_pdriver_probe and
radio_si4713_pdriver_remove.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We've been doing this for a while in Fedora without any complaints.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of doing:
[ 82.581639] tda18271 4-0060: creating new instance
[ 82.588411] Unknown device detected @ 4-0060, device not supported.
[ 82.594695] tda18271_attach: [4-0060|M] error -22 on line 1272
[ 82.600530] tda18271 4-0060: destroying instance
Print:
[ 468.740392] Unknown device (0) detected @ 4-0060, device not supported.
for the error message, to help detecting what's going wrong with the
device.
This helps to detect when the driver is using the wrong I2C bus (or have
the i2g gate switch pointing to the wrong place), on devices like cx231xx
that just return 0 on reads to a non-existent i2c device.
Reviewed-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is an internal API and belongs in v4l2-common.h, not
videodev.h. The return pointer and probe argument should be const as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Missed a few init functions on non-Intel platforms the first time :-(
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With a null request byte, these commands prevented the next commands
to be executed.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multiple user-space application instances can open the same video device, but
it only makes sense for one of them to manage the videobuffer queue and set
video format of the device. Restrict soc-camera respectively.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many video drivers implement a fixed set of frame formats and thus face a task
of finding the best match for a user-requested format. Implementing this in a
generic function has also an advantage, that different drivers with similar
supported format sets will select the same format for the user, which improves
consistency across drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows userspace to terminate a capture without waiting for the current
frame to complete.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the current source status the emma has no limitation for any PIXFMT
since the data is parsed raw and unprocessed into the memory.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L1 is deprecated and will be removed completely soon.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial em28xx std (PAL) was not passed on to the subdevs. This led to
these tvp5150 kernel log errors when running v4l2-ctl --all:
tvp5150 0-005c: VBI can't be configured without knowing number of lines
The reason was that tvp5150 was still using its own internal default: STD_ALL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_waiton() must unlock and relock ext_lock if it has to wait.
For that to happen it needs the videobuf_queue pointer.
Don't attempt to unlock/relock q->ext_lock unless it was locked in the
first place.
vb->state has to be protected by a spinlock to be safe.
This patch is based on code from Mauro Carvalho Chehab <mchehab@redhat.com>.
[mchehab@redhat.com: add extra argument to a few missing places]
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an ext_lock argument to the videobuf init functions. This allows
drivers to pass the vdev->lock pointer (or any other externally held lock)
to videobuf. For now all drivers just pass NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently videobuf uses the vb_lock mutex to lock its data structures.
But this locking will (optionally) move into the v4l2 core, which means
that in that case vb_lock shouldn't be used since the external lock is already
held.
Prepare for this by adding a pointer to such an external mutex and
don't lock if that pointer is set.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers can optionally set a pointer to a mutex in struct video_device.
The core will use that to lock before calling open, read, write, unlocked_ioctl,
poll, mmap or release.
Updated the documentation as well and ensure that v4l2-event knows about the
lock: it will unlock it before doing a blocking wait on an event and relock it
afterwards.
Ensure that the 'video_is_registered' check is done when the lock is held:
a typical disconnect will take the lock as well before unregistering the
device nodes, so to prevent race conditions the video_is_registered check
should also be done with the lock held.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now all fops except release and (unlocked_)ioctl returned an error
after the device node was unregistered. Extend this as well to the ioctl
fops. There is nothing useful that an application can do here and it
complicates the driver code unnecessarily.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver author seems to not worked on this driver since its conversion
from 2.2 to 2.4. Nobody is known to have a stradis hardware for testing. As
it still uses V4L1 API, BKL and probably some other old stuff, someone would
need to work on it to preserve the driver. Instead of investing time and
efforts to keep porting it to work with new API's, it seems better to just
drop the driver.
So, let's move it to drivers/staging and label it to die at 2.6.38, if nobody
cares enough to port parallel port support to gspca or to create a new driver
that uses the same gspca-cpia sub-driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cpia driver were re-written inside gspca driver, for USB devices. The only
functionality that were not migrated is the support for parallel port,
as:
1) the developer didn't find any hardware;
2) it doesn't seem important to keep support for a parallel port webcam,
as this is an obsolete technology;
3) the changes at gspca for it to work with parallel port would be very large;
4) this driver still uses BKL.
So, let's move it to drivers/staging and label it to die at 2.6.38, if nobody
cares enough to port parallel port support to gspca or to create a new driver
that uses the same gspca-cpia sub-driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a few ancillary static routines used by ioctl functions
that takes bttv lock internally. As we'll be adding the same lock
for all ioctl's that need, we need to properly document them, to
avoid doing double locks
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mpc512x kernel configurations without SPI support do not build:
drivers/media/video/fsl-viu.c: In function 'viu_open':
drivers/media/video/fsl-viu.c:1248: error: implicit declaration of function 'kzalloc'
drivers/media/video/fsl-viu.c:1248: warning: assignment makes pointer from integer without a cast
drivers/media/video/fsl-viu.c: In function 'viu_release':
drivers/media/video/fsl-viu.c:1335: error: implicit declaration of function 'kfree'
If CONFIG_SPI is enabled, the slab.h will be included in
linux/spi/spi.h which is included by media/v4l2-common.h
and the fsl_viu.c driver builds.
Let's incluce linux/slab.h directly to fix the build breakage.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bt8xx driver only uses the big kernel lock in its dst_ca_ioctl
function and never to serialize against other code, so we can
trivially replace it with a private mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dvb core only uses the big kernel lock in the open
and ioctl functions, which means it can be replaced with
a dvb specific mutex. Fortunately, all the ioctl functions
go through dvb_usercopy, so we can move the serialization
in there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just fill the array as necessary and terminate with 0
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Code in function cx22702_set_tps() can be slightly simplified.
Apparently gcc was smart enough to optimize it anyway, but it can't
hurt to make the code more readable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init sequence never changes so it can be marked const. Likewise,
cx22702_ops is a template and can thus be made read-only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling the same functions in if/else or switch/case branches is
inefficient. Refactor the code for a smaller binary and increased
readability.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows the removal of CONFIG_INPUT from saa7134, and
helps to create a better Kconfig dependency hierarchy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tda8425 initialization function sets up the inputmap for riva boards.
After some digging I discovered that this was for the V4L rivatv driver
that is found on sourceforge. This driver hasn't been maintained since the
last 5 years and will no longer work with the current v4l framework.
So we can safely remove this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These variables are either unconditionally set right afterward, or
already set to 0 by kzalloc.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, they get set up with the pad keytable, which they can't
actually use at all. Also add another variant of volume scancodes from
another 0xffdc device, and properly set up the 0x9e 0xffdc device as an
iMON VFD w/MCE proto IR.
Based on data and a prior patch from Anders Eriksson on the lirc list.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lest we get our keycodes wrong... Thus far, in practice, I've not found
it to actually matter, but its one of the issues raised in
https://bugzilla.kernel.org/show_bug.cgi?id=16351 that wasn't addressed
by converting to using native IR keydown/up functions.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a stab at separating the mouse (and front panel/knob) events
out to a separate input device. This is necessary in preparation for
the next patch which makes the rc-core input dev opaque to rc
drivers.
I can't verify the correctness of the patch beyond the fact that it
compiles without warnings. The driver has resisted most of my
attempts at understanding it properly...for example, the double calls
to le64_to_cpu() and be64_to_cpu() which are applied in
imon_incoming_packet() and imon_panel_key_lookup() would amount
to a bswab64() call, irregardless of the cpu endianness, and I think
the code wouldn't have worked on a big-endian machine...
- Minor alterations to apply with minimal core IR changes
- Use timer for imon keys too, since its entirely possible for the
receiver to miss release codes (either by way of another key being
pressed while the first is held or by the remote pointing away from
the recevier when the key is release. yes, I know, its ugly).
- Bump driver version number, since this is a fairly significant change
(for the much much better).
Tested successfully w/an imon knob receiver.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon driver currently reimplements its own version of ir_keyup
(along with key release timer functionality also already present in the
core IR code). A follow-up imon patch will make use of ir_keyup and the
IR stack's key release code.
Trivial extraction from David Härdeman's pending rc-core merge and
device interface abstraction patchset to facilitate merging a patch
based on his imon input dev split patch ahead of the larger churn, which
is slated for post-2.6.37-rc1 (after Dmitry's large keycode patches are
merged in mainline).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason for keeping I2C_HW_SAA7134 is to allow setting a
per-device polling interval. Just move this info to the platform
data, allowing drivers to change it per device, where needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the cx88 specific initialization for Hauppauge XVR remotes
into cx88-input, removing the need for test it inside ir-kbd-i2c.
The reference at cx88 for this symbol, at:
drivers/media/video/cx88/cx88-i2c.c: core->i2c_adap.id = I2C_HW_B_CX2388x;
drivers/media/video/cx88/cx88-vp3054-i2c.c: vp3054_i2c->adap.id = I2C_HW_B_CX2388x;
Can't be removed yet, since lirc-i2c still uses it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed the BKL from usbvision.
There was an initialization bug as well where the i2c bus was registered twice.
Although when the BKL was present no oops was generated, I did run into
other i2c problems. Now that I protect against duplicate i2c registration
that bug is now gone as well.
But trying to disconnect the USB cable while someone is still using the device
still leads to a crash.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a hack in the tuner code for the mxb board. This hack is no longer
needed since the tuner is now probed on its correct address as specified
by the mxb driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the V4L1 API from this driver, making it fully V4L2.
Also fix a bug where the /dev/videoX device was created too early, which led
to initialization problems of the camera, making it unable to capture video.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The illuminator controls should only be available to the user for the Intel
Play QX3 microscope. The implementation to inhibit the controls is intended to
be consistent with the other gspca driver implementations.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Turn the lights of the QX3 on (or off) as needed when resuming and at module load.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds basic V4L2 controls for the illuminators on the Intel
Play QX3 microscope.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some media devices (microscopes) may have one or many illuminators.
This patch makes them controlable by the applications.
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When compressed, the images take less than one byte per pixel.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove HID and polling via firmware API. Implement direct access to remote codes via memory read and write.
HID and polling via firmware api never worked 100% well and there was also some limitations which tied used remote and device together.
After that it is possible to use upcoming kernel remote controller core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Detect TerraTec Cinergy T Stick Dual RC remote config using device
USB ID instead of device EEPROM hash. It was found that there is
devices with slightly different EEPROM content...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID [0ccd:0099] for TerraTec Cinergy T Stick Dual RC.
Device is based for AF9015 + AF9013 + 2 x MxL5007T chips.
Thanks to the TerraTec!
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 490ade7e3f4474f626a8f5d778ead4e599b94fbc merge conflict fix
leads situation where last nine device definitions were overridden mistakenly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the vtx (aka videotext aka teletext) API from the v4l2 core.
This API was scheduled for removal in kernel 2.6.35.
The vtx device nodes have been superseded by vbi device nodes
for many years. No applications exist that use the vtx support.
Of the two i2c drivers that actually support this API the saa5249
has been impossible to use for a year now and no known hardware
that supports this device exists. The saa5246a is theoretically
supported by the old mxb boards, but it never actually worked.
In summary: there is no hardware that can use this API and there
are no applications actually implementing this API.
The vtx support still reserves minors 192-223 and we would really
like to reuse those for upcoming new functionality. In the unlikely
event that new hardware appears that wants to use the functionality
provided by the vtx API, then that functionality should be build
around the sliced VBI API instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These old i2c teletext drivers are not supported by any hardware and cannot be
tested anymore.
Note that while the mxb board seemingly used the saa5246a driver, in reality
this teletext driver never worked.
These drivers are removed as part of the vtx feature removal, originally
scheduled for 2.6.35.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
bit 3(LK) indicates that the Vstatus is locked.
Currently using bit 7(CF) which is usually present, results in early
aborted search in FEC_AUTO and missing channels.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
WARNING: please, no space before tabs
+ * ^IPOR = Power on Reset (VCC H=<2.2v L=>2.2v)$
WARNING: unnecessary whitespace before a quoted newline
+ deb_info("Frq=%d x=%d N=%d A=%d \n", frequency, x, N, A);
WARNING: please, no space before tabs
+^Ielse ^I^I/*frequency up to 2150000*/$
WARNING: unnecessary whitespace before a quoted newline
+ deb_info("Data 0=[%x%x%x%x] \n", data[0], data[1], data[2], data[3]);
WARNING: unnecessary whitespace before a quoted newline
+ deb_info("Data 2=[%x%x] \n", data[2], data[3]);
Cc: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuner used in Sharp BS2F7VZ7395 dvbs module.
When ix2505v tuner is attached to stv0288 form this module.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The same expression is tested twice and the result is the same each time.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@expression@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding the USB ID for my TerraTec Electronic GmbH Cinergy T RC MKII
[0ccd:0097] and hooking it up into af9015, on top of your new NXP TDA18218
patches, makes it work for me.
Just the shipped IR remote control doesn't seem to create keycode events
yet (tested with different remote=%d parameters), are there any hints to
add support for that?
[ 2.250022] usb 1-10: new high speed USB device using ehci_hcd and address 5
[ 2.369287] usb 1-10: New USB device found, idVendor=0ccd, idProduct=0097
[ 2.369290] usb 1-10: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.369293] usb 1-10: Product: USB2.0 DVB-T TV Stick
[ 2.369294] usb 1-10: Manufacturer: NEWMI
[ 2.369296] usb 1-10: SerialNumber: 010101010600001
[ 2.534023] usbcore: registered new interface driver hiddev
[ 2.537235] input: NEWMI USB2.0 DVB-T TV Stick as /devices/pci0000:00/0000:00:02.1/usb1/1-10/1-10:1.1/input/input0
[ 2.537323] generic-usb 0003:0CCD:0097.0001: input,hidraw0: USB HID v1.01 Keyboard [NEWMI USB2.0 DVB-T TV Stick] on usb-0000:00:02.1-10/input1
[ 2.537349] usbcore: registered new interface driver usbhid
[ 2.537351] usbhid: USB HID core driver
[ 3.263177] generic-usb 0003:04D9:1603.0002: input,hidraw1: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:02.0-8.1/input0
[ 3.286946] generic-usb 0003:04D9:1603.0003: input,hidraw2: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:02.0-8.1/input1
[ 3.467136] generic-usb 0003:046D:C050.0004: input,hidraw3: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-8.2/input0
[ 3.660890] generic-usb 0003:10D5:000D.0005: input,hidraw4: USB HID v1.10 Keyboard [No brand SP02-A1] on usb-0000:00:02.0-8.3/input0
[ 5.567632] dvb-usb: found a 'TerraTec Cinergy T Stick RC' in cold state, will try to load a firmware
[ 5.693497] dvb-usb: downloading firmware from file 'dvb-usb-af9015.fw'
[ 5.773109] dvb-usb: found a 'TerraTec Cinergy T Stick RC' in warm state.
[ 5.773168] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[ 5.774290] DVB: registering new adapter (TerraTec Cinergy T Stick RC)
[ 6.007696] af9013: firmware version:5.1.0
[ 6.010843] DVB: registering adapter 0 frontend 0 (Afatech AF9013 DVB-T)...
[ 6.032697] tda18218: NXP TDA18218HN successfully identified.
[ 6.034442] dvb-usb: TerraTec Cinergy T Stick RC successfully initialized and connected.
[ 6.040612] usbcore: registered new interface driver dvb_usb_af9015
[mchehab@redhat.com: Fix merge conflict with another board addition]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Making static data const avoids allocation of additional r/w memory and
reduces initialisation time. It also provides some additional opportunities
for compiler optimisations.
Signed-off-by: Lawrence Rust <lvr@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx88/cx88-dsp.c: In function ‘detect_a2_a2m_eiaj’:
drivers/media/video/cx88/cx88-dsp.c:158: warning: ‘carrier_freq’ may be used uninitialized in this function
drivers/media/video/cx88/cx88-dsp.c:158: warning: ‘stereo_freq’ may be used uninitialized in this function
drivers/media/video/cx88/cx88-dsp.c:158: warning: ‘dual_freq’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace direct access to the v4l2_subdev priv field with the inline
v4l2_get_subdevdata method.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using an enum and removing the default case from switch statements accessing
the value enables the compiler to emit a warning (enabled with -Wall) when an
audio mode is not handled.
This highlights an omission in the function cx88_dsp_detect_stereo_sap()
(in cx88-dsp.c) not handling WW_EIAJ and WW_M.
Signed-off-by: Lawrence Rust <lawrence@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Error codes are stored in rc, but the return value is always 0. Return rc
instead.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
local idexpression x;
constant C;
@@
if (...) { ...
x = -C
... when != x
(
return <+...x...+>;
|
return NULL;
|
return;
|
* return ...;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In each case, error codes are stored in rc, but the return value is always
0. Return rc instead.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
local idexpression x;
constant C;
@@
if (...) { ...
x = -C
... when != x
(
return <+...x...+>;
|
return NULL;
|
return;
|
* return ...;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Error codes are stored in res, but the return value is always 0. Return
res instead.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
local idexpression x;
constant C;
@@
if (...) { ...
x = -C
... when != x
(
return <+...x...+>;
|
return NULL;
|
return;
|
* return ...;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cx23885/cx23885-video.c, cx88/cx88-video.c, davinci/vpif_capture.c, and
davinci/vpif_display.c, group the aligned code into a single if branch.
In saa7134/saa7134-video.c, outdent the code following the if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
