The original i965, including the revised G35 and Q35, requires an
alignment of 128K for the display surface with linear memory, so
increase the requirement from 64k for these chipsets. For the later
chipsets in the i965 family, only a 4k alignment is required. (So
long as we do not start performing asynchronous flips.)
Note the impact of this should be slight as on i965 we should be using a
tiled frontbuffer for anything up to a 4096x4096 display.
v2: compilation fixes and note that the docs do not exclude the G35 from
the extra alignment.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Unmask the bits for link training reporting before starting link
training. If stage 1 training finished before we unmask them, then we'd
spin around in a loop a few times until smashing on through. Which is
harmless, since training _did_ succeed, it just looks ugly in dmesg.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
NUM_TV_MODES is the same as ARRAY_SIZE(tv_modes). In the end, I
decided it was cleaner to remove NUM_TV_MODES and just use
ARRAY_SIZE(tv_modes) through out.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
References:
Bug 26691 - Spurious hangcheck whilst executing a long shader over a
large vertex buffer
https://bugs.freedesktop.org/show_bug.cgi?id=26691
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
We generally issue an error message at the point of failure, and so this
warning with a fairly pointless stacktrace is superfluous and ugly.
Needless to say, the common trigger for this WARN happens to be EIO
where this is pure noise.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Since mode->clock is in kHz we should be checking against 2700000
instead of just 27000. This patch gets my x201s working again (well
working as well as it ever was anyway).
When looking for this I also noticed we set link_bw to 270000, but the
calculation is different. Does it also need to use kHz or we using
10kHz internally?
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/intel_tv.c|479 col 16| warning: cast truncates bits
from constant value (8 becomes 0)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_drv.c|485 col 25| warning: symbol 'i915_pm_ops' was not declared. Should it be static?
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_drv.c|100 col 18| warning: Initializer entry defined twice
drivers/gpu/drm/i915/i915_drv.c|101 col 3| also defined here
drivers/gpu/drm/i915/i915_drv.c|117 col 18| warning: Initializer entry defined twice
drivers/gpu/drm/i915/i915_drv.c|118 col 3| also defined here
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_drv.h|676 col 19| warning: dubious bitfield without explicit `signed' or `unsigned'
drivers/gpu/drm/i915/i915_drv.h|712 col 19| warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Simple fix for error propagation along the old UMS path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
checkpatch complains about this define:
WARNING: space prohibited between function name and open parenthesis '('
+#define GEN6_RENDER TIMEOUT_COUNTER_EXPIRED (1 << 6)
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
About 0.2W power can be saved on one HP laptop.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The hardware team suggest that the "large buffer" method should be
used to calculate the cursor watermark under non-SR state as well,
which is to avoid the flicker when FBC is enabled on Ironlake.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In SR mode cursor plane watermark calculation uses same formula
like display plane. This one fixes the case for 965G and G45.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The total self-refresh fifo entry size for display plane is 512
instead of 128 for 965G. Also fix WM value mask for 965G.
About 1.0W power can be saved on one T61 laptop after the self-refresh
watermark is configured correctly.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For self-refresh mode WM calculation's "line time" should use
mode's htotal instead of hdisplay. "surface width" is the hdisplay
for display plane and 64 for cursor plane.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This one adds support for eDP that connected on PCH DP-D port
instead of CPU DP-A port, and only DP-D port could be used for eDP.
https://bugs.freedesktop.org/show_bug.cgi?id=27220
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Tested-by: Templar <templar@rshc.de>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Having two sets has made me think I caught a bug more than once now.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
On some machines (currently only the Toshiba Tecra A11 is known), the GPU
locks up when modeset is forced on LID open. This patch adds a new DMI
blacklist and omits modesetting for all matches.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15550
Signed-off-by: Thomas Bächler <thomas@archlinux.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This interface allows userspace to request hyperz support, it probably
needs more locking, and really reporting that you can have hyperz is racy
since someone else might get it before you do.
v2: modify so we pass 0 valued packets to let DDX/r300c keep working.
also fixed incorrect 0x4f1c reference.
v3: fixup zb_bw_cntl so older drivers keep working
v4: add locking, fixup SC_HYPERZ_EN - patch stream to disable hiz
Signed-off-by: Dave Airlie <airlied@redhat.com>
This migrates a bunch of DRM_DEBUG->DRM_DEBUG_KMS so we can get more modesetting related info without all the other ioctl handling easily.
Also the PM code moves to DRM_DEBUG_DRIVER mostly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of ../drm-nouveau-next: (77 commits)
drm/nouveau: set TASK_(UN)INTERRUPTIBLE before schedule_timeout()
drm/nv50: fix some not-error error messages
drm/nouveau: introduce gpio engine
drm/nv50: correct wait condition for instmem flush
drm/nouveau: Fix TV-out detection on unposted cards lacking a usable DCB table.
drm/nouveau: Get rid of the remaining VGA CRTC locking.
drm/nouveau: Move display init to a new nouveau_engine.
drm/nouveau: Put back the old 2-messages I2C slave test.
drm/nouveau: Reset AGP before running the init scripts.
drm/nv30: Init the PFB+0x3xx memory timing regs.
drm/nouveau: disable hotplug detect around DP link training
drm/nv50: add function to control GPIO IRQ reporting
drm/nouveau: add nv_mask register accessor
drm/nouveau: fix build without CONFIG_ACPI
drm/nouveau: Reset CRTC owner to 0 before BIOS init.
drm/nouveau: No need to lock/unlock the VGA CRTC regs all the time.
drm/nouveau: Remove useless CRTC_OWNER logging.
drm/nouveau: Add some generic I2C gadget detection code.
drm/i2c/ch7006: Don't assume that the specified config points to static memory.
drm/nv04-nv3x: Implement init-compute-mem.
...
Conflicts:
drivers/gpu/drm/nouveau/nouveau_bios.c
* 'drm-radeon-next' of ../drm-radeon-next: (333 commits)
drm/radeon/kms: trivial code style fixes for audio
drm/radeon: remove viewport transform from r6xx/r7xx blit emit
drm/radeon: group r6xx/r7xx newly sequential blit state
drm/radeon: reorder r6xx/r7xx blit state emit to make more regs sequential
drm/radeon: r6xx/r7xx move vport clipping to a single packet
drm/radeon: group r6xx/r7xx sequential blit state
drm/radeon: remove duplicate state emit in r6xx/r7xx blit
drm/radeon: add comments to r6xx/r7xx blit state
drm/radeon/kms/r7xx: add workaround for hw issue with HDP flush
drm/radeon/kms: remove rs4xx gart limit
drm: radeon: fix sign bug
drm/radeon/kms: check/restore sanity before doing anything else with GPU.
drm/radeon: fall back to GTT if bo creation/validation in VRAM fails.
drm/radeon/kms: add ioport register access
drm/radeon/kms: enable HDMI audio on RS600/RS690/RS740
drm/radeon/kms: track audio engine state, do not use not setup timer
drm/radeon/kms/r6xx+: add query for tile config (v2)
drm/radeon/kms: fix CS alignment checking for tiling (v2)
drm/radeon/kms: add tiling support to the cs checker for r6xx/r7xx
drm/radeon/kms: Add crtc tiling setup support for evergreen
...
sil164 transmitters are used for DVI outputs on Intel/nvidia and ATI setups.
So far only nouveau can use this driver.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Tested-by: Patrice Mandin <patmandin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixed brace, macro and spacing coding style issues, and a C99 comment.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The device name is tightly coupled and created at the same time as the
master->unique address, so we need to free it with the master. Currently
we overwrite it each time we create a new master:
unreferenced object 0xe32c54b0 (size 32):
comm "Xorg", pid 1455, jiffies 4294721798 (age 3196.879s)
hex dump (first 32 bytes):
69 39 31 35 40 70 63 69 3a 30 30 30 30 3a 30 30 i915@pci:0000:00
3a 30 32 2e 30 00 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 :02.0.kkkkkkkkk.
backtrace:
[<c04e5657>] create_object+0x124/0x1f1
[<c07cf0f0>] kmemleak_alloc+0x4c/0x90
[<c04db84c>] __kmalloc+0x155/0x175
[<f8316665>] drm_setversion+0x11d/0x1b1 [drm]
[<f83148d4>] drm_ioctl+0x29a/0x356 [drm]
[<c04f27c4>] vfs_ioctl+0x33/0x91
[<c04f31cf>] do_vfs_ioctl+0x46b/0x496
[<c04f3240>] sys_ioctl+0x46/0x66
[<c040325f>] sysenter_do_call+0x12/0x38
[<ffffffff>] 0xffffffff
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
/* A typical clean-up sequence for objects stored in an idr tree, will
* use idr_for_each() to free all objects, if necessary, then
* idr_remove_all() to remove all ids, and idr_destroy() to free
* up the cached idr_layers.
*/
We were missing the vital idr_rmove_all() step and so were leaking
the used layers for every dri client:
unreferenced object 0xf32133c0 (size 148):
comm "plymouthd", pid 131, jiffies 4294678490 (age 2308.030s)
hex dump (first 32 bytes):
04 00 00 00 00 00 00 00 00 00 00 00 00 40 19 f3 .............@..
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<c04e5657>] create_object+0x124/0x1f1
[<c07cf100>] kmemleak_alloc+0x4c/0x90
[<c04db6a9>] kmem_cache_alloc+0xee/0x13c
[<c05c3d25>] idr_pre_get+0x24/0x61
[<f8315c9c>] drm_gem_handle_create+0x27/0x7f [drm]
[<f89925b2>] i915_gem_create_ioctl+0x4f/0x71 [i915]
[<f83148ac>] drm_ioctl+0x272/0x356 [drm]
[<c04f27c4>] vfs_ioctl+0x33/0x91
[<c04f31cf>] do_vfs_ioctl+0x46b/0x496
[<c04f3240>] sys_ioctl+0x46/0x66
[<c040325f>] sysenter_do_call+0x12/0x38
[<ffffffff>] 0xffffffff
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15803
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
set_current_state() is called only once before the first iteration.
After return from schedule_timeout() current state is TASK_RUNNING. If
we are going to wait again, set_current_state() must be called.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Trivial fix to set y1 = y2 = 0.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We aren't using it, so no need. Save additional dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
group state that is emitted sequentially into fewer packets.
This saves a number of dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
group state that is emitted sequentially into fewer packets.
This saves a number of dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use of HDP_*_COHERENCY_FLUSH_CNTL can cause a hang in certain
situations. Add workaround.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We used to limit the rs4xx gart aperture to 32 MB, but I suspect
that was due to not meeting the alignment requirements of the
aperture. This patch should only be applied after:
"drm/radeon/kms: fix gtt MC base alignment on rs4xx/rs690/rs740 asics"
has been applied.
This patch should probably soak for a bit in d-r-t.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The "error" variable is unsigned so it's never less than zero. I
changed it to check if (freq < current_freq) directly.
"best_error" is also unsigned so "best_error - 100" could be a large
number instead of a negative. Since "error" is unsigned it is never
less than a negative and so the cases where "best_error" is less than or
equal to 100 are false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems using kexec, the new kernel is booted straight from the old kernel, without any warning to the graphics driver. So the GPU is basically left as-is in a running state, however the CPU side is completly reset.
Without stating the saneness of anyone using kexec on live systems, we should at least try not to crash the GPU. This patch resets 3 registers to 0 that could cause bad things to happen to the running system.
This allows kexec to work on a Power6/RN50 system.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a problem where on low VRAM cards we'd run out of space for validation.
[airlied: Tested on my M7, Thinkpad T42, compiz works with no problems.]
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is required for the NB_MISC regs on rs780/rs880 which
means HDMI/DVI/DP ports using PCIEPHY won't work without
it. It might also help with s/r (asic init) issues on other
atombios cards.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28774
and similar issues reported by Alberto Milone.
[airlied: Squash io fix patch]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We will need method of selecting encoder that should receive HDMI block. For
now we assign HDMI block to first enabled encoder. Hopefully there are not many
RS6x0 chips with two digital encoders.
[airlied: add RS740 checks as per Alex suggestion.]
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed to enable audio support on devices using polling. In case user
decides to disable audio (module parameter) we still will try to use timer in
r600_audio_enable_polling. This would lead to BUG in kernel/timer.c.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace needs this information to access tiled
buffers via the CPU.
v2: rebased on evergreen accel changes
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check for relocs for DB_DEPTH_INFO, CB_COLOR*_INFO, and texture
resources.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rv6xx/rv7xx/evergreen families supported; older asics did
not have an internal thermal sensor.
Note, not all oems use the internal thermal sensor, so it's
only exposed in cases where it is used.
Note also, that most laptops use an oem specific ACPI solution for
GPU thermal information rather than using the internal thermal
sensor directly.
v2: export millidegrees celsius, use hwmon device properly.
v3: fix Kconfig
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
By calling the ATIF method in the radeon driver we can make sure
that hotkeys such as the video switch key emit ACPI events when
pressed.
agd5f: fix warning
Signed-off-by: Alberto Milone <alberto.milone@canonical.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some tables have delays that can cause the timeout to hit
even when not intended.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=27744
and related bugs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Make the logic in r100_pll_errata_after_index() match the other
errata functions
- Use rdev->family rather than rdev->flags & RADEON_FAMILY_MASK for kms
- replace rn50 check using ids with ASIC_IS_RN50 convenience macro
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We're adjusting horizontal timings only here, moving vsync was just a
slavish translation of a typo in the X server.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix incorrectly reporting 'default' power profile, when it is set to 'mid'.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix error from the last pull request. Making sure we shut the panel off
is more correct and saves power.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: add pipe A force quirks to i915 driver
drm/i915: Fix panel fitting regression since 734b4157
drm/i915: fix deadlock in fb teardown
drm/i915: don't free non-existent compressed llb on ILK+
agp/intel: Use the correct mask to detect i830 aperture size.
drm/i915: disable FBC when more than one pipe is active
drm/i915: Use the correct scanout alignment for fbcon.
drm/i915: make sure eDP panel is turned on
drm/i915: add PANEL_UNLOCK_REGS definition
drm/i915: Make G4X-style PLL search more permissive
drm/i915: Clear any existing dither mode prior to enabling spatial dithering
drm/i915: handle shared framebuffers when flipping
drm/i915: Explosion following OOM in do_execbuffer.
gpu/drm/i915: Add a blacklist to omit modeset on LID open
Ported over from the old UMS list. Unfortunately they're still
necessary especially on older laptop platforms.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=22126.
Tested-by: Xavier <shiningxc@gmail.com>
Tested-by: Diego Escalante Urrelo <diegoe@gnome.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The crtc mode fixup is run after the encoders adjust the mode to fit on
their output, so don't reset the mode!
Fixes:
Bug 29057 - display corruption under 800x600 on netbook
(1024x600) with 'Full Aspect' scaling
https://bugs.freedesktop.org/show_bug.cgi?id=29057
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Xun Fang <xunx.fang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
At module unload time we'll tear down the fbdev state. We do so under
the struct mutex, so we shouldn't try to use the unlocked variant of
the GEM object unreference function or we may deadlock.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We should only free the compressed llb if we allocated it in the first
place otherwise we'll panic at unload time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We're really supposed to do this to avoid trouble with underflows when
multiple planes are active.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=26987.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: fangxun <xunx.fang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes a potential modesetting error during boot with plymouth on
Broadwater and Crestline introduced with 9df47c. The framebuffer was
hard-coding an alignment of 64K, but the modesetting code required the
documented alignment of 128K. The result was that we would attempt to
unbind the pinned fbcon buffer, triggering an ERROR and ultimately
failing the mode change.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
When enabling the eDP port, we need to make sure the panel is turned on
after training the link. If we don't, it likely won't come back after
suspend or may not come up at all.
For unknown reasons, unlocking the panel regs before initiating a power
on sequence is necessary. There are known bugs in the PCH panel
sequencing logic, apparently this is one possible workaround.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28739.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: "Paulo J. S. Silva" <pjssilva@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In some cases, unlocking the panel regs is safe and can help us avoid a
flickery, full mode set sequence. So define the unlock key and use it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes an Ironlake laptop with a 68.940MHz 1280x800 panel and 120MHz SSC
reference clock.
More generally, the 0.488% tolerance used before is just too tight to
reliably find a PLL setting. I extracted the search algorithm and
modified it to find the dot clocks with maximum error over the valid
range for the given output type:
http://people.freedesktop.org/~ajax/intel_g4x_find_best_pll.c
This gave:
Worst dotclock for Ironlake DAC refclk is 350000kHz (error 0.00571)
Worst dotclock for Ironlake SL-LVDS refclk is 102321kHz (error 0.00524)
Worst dotclock for Ironlake DL-LVDS refclk is 219642kHz (error 0.00488)
Worst dotclock for Ironlake SL-LVDS SSC refclk is 84374kHz (error 0.00529)
Worst dotclock for Ironlake DL-LVDS SSC refclk is 183035kHz (error 0.00488)
Worst dotclock for G4X SDVO refclk is 267600kHz (error 0.00448)
Worst dotclock for G4X HDMI refclk is 334400kHz (error 0.00478)
Worst dotclock for G4X SL-LVDS refclk is 95571kHz (error 0.00449)
Worst dotclock for G4X DL-LVDS refclk is 224000kHz (error 0.00510)
Signed-off-by: Adam Jackson <ajax@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
We cannot the initial configuration set by the BIOS not to have a dither
mode enabled which conflicts with our enabling the Spatial Temporal 1
dither mode for PCH. In particular, the BIOS may either enable temporal
dithering or the Spatial Temporal 2 with the result that we enable pure
temporal dithering. Temporal dithering looks bad and is perceived as a
flicker.
Fixes:
Bug 29248 - [Arrandale] Annoying flicker on internal panel, goes away
after suspend to RAM
https://bugs.freedesktop.org/show_bug.cgi?id=29248
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If a framebuffer is shared across CRTCs, the x,y position of one of them
is likely to be something other than the origin (e.g. for extended
desktop configs). So calculate the offset at flip time so such
configurations can work.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=28518.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Thomas M. <tmezzadra@gmail.com>
Tested-by: fangxun <xunx.fang@intel.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
I was hoping we could detect I2C devices at a given address without
actually writing data into them, but apparently some DDC slaves get
confused with 0-bytes transactions. Put the good old test back.
Reported-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
BIOS scripts usually make an attempt to reset the AGP controller,
however on some nv4x cards doing it properly involves switching FW off
and on: if we do that without updating the AGP bridge settings
accordingly (e.g. with the corresponding calls to agp_enable()) we
will be locking ourselves out of the card MMIO space. Do it from
nouveau_mem_reset_agp() before the init scripts are executed.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes the randomly flashing vertical lines seen on some nv3x after a
cold-boot.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes suspend+multihead on some boards that also use BIOS scripts for
modesetting.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Locking only makes sense in the VBIOS parsing code as it's executed
before CRTC init.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Clean up and move the external TV encoder detection code to
nouveau_i2c.c, it's also going to be useful for external TMDS and DDC
detection.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Init-compute-mem was the last piece missing for nv0x-nv3x card
cold-booting. This implementation is somewhat lacking but it's been
reported to work on most chipsets it was tested in. Let me know if it
breaks suspend to RAM for you.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Tested-by: Patrice Mandin <patmandin@gmail.com>
Tested-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Xavier Chantry <chantry.xavier@gmail.com>
Tested-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Chris Wilson