On resuming, the opmode may have to be able to talk
to the WoWLAN/D3 firmware in order to query it about
its status and wakeup reasons. To do that, the opmode
has to call the new d3_resume() transport API which
will set up the device for command communcation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Writing 130 dwords into the device one by one is
rather inefficient, every one needs to lock, grab
NIC access (a few register reads/writes) and then
write the address and data registers.
Use the new memory clearing function to make this
easier and faster.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sending a NULL pointer to iwl_trans_write_mem allows now
to zero SRAM.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enabling the RF-kill interrupt is sufficient for getting
RF-kill notifications, and no other interrupt is needed
as the device isn't functional when suspended and will be
restarted/reconfigured when mac80211 resumes it later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The dma_addr_t type is a scalar value, so it should
just be assigned, not memset.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The sanity checks allow 1 and 2 byte reads/writes of the extended
PCI config space to proceed; however, the code only supports 4
byte reads/writes. This patch adds support for 1 and 2 byte
reads/writes of the extended PCI config space.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PCI config space access offsets < 256 for device '0',
bcma_extpci_write_config performs an 'ioremap_nocache' on a 4 byte
section of the PCI config space (an area that has already
previously been mapped), and then subsequently unmaps that 4 byte
section. This can't be a good thing for future read access from
that now unmapped location. Modify the config space writes to use
the existing access functions (similar to how it is done for the reads).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consistently jump to the 'out' label for error conditions (adds
missing check for 'func' validity in bcma_extpci_write_config).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'val' has already been read by the prior call to 'mips_busprobe32';
this 'readl' is unnecessary.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default irqflag assignment for the I2S core on some Broadcom
4716/4748 devices is invalid and needs to be corrected (from the
Broadcom SDK).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It brings the following goodies:
- LLCP socket timestamping (To be used e.g with the recently released nfctool
application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
application code to safely include it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=YeWq
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the first NFC patchset targeted at the 3.9 merge window.
It brings the following goodies:
- LLCP socket timestamping (To be used e.g with the recently released nfctool
application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
application code to safely include it."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a reported CPU soft lockup where the tasklet tries to acquire the
lock and blocks while ath_prepare_reset (holding the lock) waits for it
to complete.
Cc: stable@vger.kernel.org
Reported-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: fix rx flush handling" added a deadlock that happens
because ath_rx_tasklet is called in a section that has already taken the
rx buffer lock.
It seems that the only purpose of the rxbuflock was a band-aid fix to the
reset vs rx tasklet race, which has been properly fixed in the commit
"ath9k: add a better fix for the rx tasklet vs rx flush race".
Now that the fix is in, we can safely remove the lock to avoid such issues.
Cc: stable@vger.kernel.org
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nfc.h being GPL makes it quite controversial for non GPL applications to
include it.
Moreover, nfc.h only includes structures and API definitions that are hardly
copyrightable.
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.
Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use dereferenced pointer in sizeof instead of pointer itself.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update the PCI configuration for BCM4706 and BCM4716 per the 2011
Broadcom SDK.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Improves stability on affected devices and also fixes the Tx IQ calibration
related regression on some AR9340 devices such as the TP-Link TL-WDR4300.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The irq signal numbers that are send by the cpu are increased by 2 from
the number programmed into the mips core by bcma.
Return the irq number on which the irqs are send in bcma_core_irq() now.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This error was introduced in:
commit e3f05a42fa
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Fri Jan 4 00:51:21 2013 +0100
bcma: mips: explicit assign IRQ numbers
CC drivers/bcma/driver_mips.o
drivers/bcma/driver_mips.c: In function 'bcma_core_mips_init':
drivers/bcma/driver_mips.c:302:4: error: implicit declaration of
function 'bcma_core_irq' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[6]: *** [drivers/bcma/driver_mips.o] Error 1
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a copy+paste error in ar9002 for the endless spectral mode,
fix that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the beacon timestamp once during "transmission" so the
monitor interface also gets a timestamped beacon.
Also use a common base between TX timestamp and RX
mactime. This eliminates "TX" path delay, which shows up
as a constant error in Toffset.
Get the global TSF once before iterating over all RX HWs,
so they all set a mactime with the same time base.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
devm_kzalloc allocates memory that is released when a driver detaches.
This patch uses devm_kzalloc for data that is allocated in the probe
function of a platform device and is only freed in the remove function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Cc: stable@vger.kernel.org
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now the rx flush is not doing anything useful on AR9003+, as it only
works if the buffers in the rx FIFO have not been purged yet, as is done
by ath_stoprecv.
To fix this, always call ath_flushrecv from within ath_stoprecv before
the FIFO is emptied, but still after the hw receive path has been stopped.
This ensures that frames received (and ACKed by the hardware) shortly before
a reset will be seen by the software, which should improve A-MPDU session
stability.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that the rx tasklet is no longer running when entering the reset path.
Also remove the distinction between flush and no-flush frame processing.
If a frame has been received and ACKed by the hardware, the stack needs to see
it, so that the BA receive window does not go out of sync.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During teardown, mac80211 will not return a new beacon. This is normal and
handled properly in the driver, so there's no need to spam the user with a kernel
warning here.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the next beacon is sent, the ath_buf from the previous run is reused.
If getting a new beacon from mac80211 fails, bf->bf_mpdu is not reset, yet
the skb is freed, leading to a double-free on the next beacon tx attempt,
resulting in a system crash.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9300 the rx FIFO needs to be empty during reset to ensure that no
further DMA activity is generated, otherwise it might lead to memory
corruption issues.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.
Cc: <stable@vger.kernel.org>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BAND_G is implicit when BAND_GN is present.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently "adapter->config_bands" is updated during infra
association only if channel is provided by user in "iw connect"
command. config_bands is used while preparing association
request to calculate supported rates by intersecting our rates
with the rates advertised by AP.
There is corner case in which we include zero rates in
supported rates TLV based on previous IBSS network history,
which leads to association failure.
This patch fixes the problem by correctly updating config_bands.
Cc: "3.7.y" <stable@vger.kernel.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 1a9193185f "regulatory: code cleanup"
changed is_ht40_allowed without considering that IEEE80211_CHAN_NO_HT40 is
not just one flag, but two.
This is causing HT40- to be blocked completely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The uuid should be printed in the CPU endianness and not in little-endian.
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The socket from which a mgmt_set_powered command was received should
only receive the command response but no new_settings event.
The mgmt_powered() function which is used to handle the situation with
the HCI_AUTO_OFF flag tries to check for a pending command to know which
socket to skip the event for, but since the pending command hasn't been
added this will not happen.
This patch fixes the issue by adding the pending command for the
HCI_AUTO_OFF case and thereby ensures that mgmt_powered() will skip the
right socket when sending the new_settings event, but still send the
proper response to the socket where the command came from.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Management commands should whenever possible fail with proper command
status or command complete events. This patch fixes the
mgmt_start_discovery command to do this for the failure cases where an
incorrect parameter value was passed to it ("not supported" if the
parameter value was valid but the controller doesn't support it and
"invalid params" if it isn't valid at all).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
All mgmt_set_* commands that take a boolean value encoded in the form of
a byte should only accept the values 0x00 and 0x01. This patch adds the
necessary checks for this and returns "invalid params" responses if
anything else is provided as the value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch fixes sections of code that do not need hci_lock_dev to be
outside of the lock. Such sections include code that do not touch the
hdev at all as well as sections which just read a single byte from the
supported_features value (i.e. all lmp_*_capable() macros).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The concept of Class of Device only exists for BR/EDR controllers. The
mgmt_set_dev_class command should therefore return a proper "not
supported" error if it is attempted for a controller that doesn't
support BR/EDR (e.g. a single mode LE-only one).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The two lowest bits of the minor device class value are reserved and
should be zero, and the three highest bits of the major device class
likewise. The management code should therefore test for this and return
a proper "invalid params" error if the condition is not met.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
All management events are expected to indicate successful completion
through a command complete event, however the load long term keys
command was missing this. This patch adds the missing event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
All management commands are expected to indicate successful completion
through a command complete event however the confirm name command was
missing it. This patch add the sending of the missing event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
