Commit graph

175 commits

Author SHA1 Message Date
Matt Carlson
141518c958 tg3: Add some VPD preprocessor constants
This patch cleans up the VPD code by creating preprocessor definitions
and using them in the place of hardcoded constants.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 13:18:04 -08:00
Matt Carlson
b703df6f62 tg3: Add 57765 asic rev
This patch adds the 57765 asic revision.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 13:18:03 -08:00
Matt Carlson
19cfaecc09 tg3: Make TSS enable independent of MSI-X enable
The 57765 asic rev has MSI-X capability, but does not support TSS.  This
patch changes the tx paths so that TSS is explicitly mentioned, rather
than implied through the ENABLE_MSIX flag.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 13:18:02 -08:00
Alexander Duyck
f4188d8aff tg3: remove use of skb_dma_map/unmap
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02 19:57:15 -08:00
Matt Carlson
5001e2f638 tg3: Fix DIDs, Enable 5717 support
This patch fixes the 5717 variant device ID enumerations and adds those
DIDs to the PCI ID table.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:54 -08:00
Matt Carlson
b196c7e45f tg3: Add rx prod ring consolidation
This patch adds code to funnel each MSI-X vector's rx packet buffers
into a single set of producer rings which will then be submitted to the
hardware.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:54 -08:00
Matt Carlson
66711e6663 tg3: Create aliases for rx producer mailbox regs
The rx producer mailbox registers are used in several spots in the code.
The addition of TG3_64BIT_REG_LOW makes register references
uncomfortably long.  This patch creates an alias for the standard and
jumbo ring producer index registers to make the code cleaner.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:53 -08:00
Matt Carlson
2b2cdb65be tg3: Lay proucer ring handling groundwork
The patch increases the number of producer rings available and
implements the constructor and destructor code that deals with them.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:51 -08:00
Matt Carlson
411da6407e tg3: rename rx_[std|jmb]_ptr
A later patch is going to add consumer indicies for the producer rings.
To keep things readable, this patch renames rx_[std|jmb]_ptr to
rx_[std|jmb]_prod_idx.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:49 -08:00
Matt Carlson
cbf9ca6cf8 tg3: Allow DMAs to cross cacheline boundaries
By default, the 5717 (and future chips) break up PCIe DMA packets across
cacheline boundaries.  This isn't necessary on x86.  This patch
selectively loosens the restriction.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:43 -08:00
Matt Carlson
615774fe59 tg3: Use tg3_start_xmit_dma_bug for 5717 A0
The A0 revision of the 5717 has problems with short packet fragments.
It needs to use the tg3_start_xmit_dma_bug() routine.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:41 -08:00
Matt Carlson
e849cdc309 tg3: Add new HW_TSO_3 flag for 5717
The 5717 sets up TSO slightly differently in the transmit path.  It
looks like this method will be the new way of doing things.  This patch
defines a flag to indicate this.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:40 -08:00
Matt Carlson
f66a29b03a tg3: Move TG3_FLG2_PROTECTED_NVRAM to tg3_flags3
We need room for another TSO flag and it would be most efficient if it
resided in tg3_flags2.  This patch moves the TG3_FLG2_PROTECTED_NVRAM
to tg3_flags3 to make room.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:39 -08:00
Matt Carlson
c2060fe1f3 tg3: Add 5717 phy ID
This patch adds the 5717 phy ID.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-15 22:14:35 -08:00
Matt Carlson
c73430d04e tg3: Add 50610M phy ID for 5785
This patch adds the 50610M phy ID for 5785.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-02 23:39:10 -08:00
Matt Carlson
0e5f784c77 tg3: Add AC131 power down support
The AC131 does not respect the power down bit (bit 11) of the MII
Control Register (reg 0x0).  Instead, software is required to put the
phy into standby power down mode through the shadow register set.  This
patch implements support for the AC131 standby power down mode.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-02 23:39:05 -08:00
Matt Carlson
788a035e60 tg3: Improve 5785 PCIe performance
This patch improves 5785 performance by allowing the write DMA engine to
request larger DMA burst sizes than it otherwise would.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-02 23:39:03 -08:00
Matt Carlson
52cdf8526f tg3: Prevent a PCIe tx glitch
This patch prevents a PCIe tx glitch by allowing the transmitter to go
to a low power state.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-02 23:39:02 -08:00
Matt Carlson
3f0e3ad723 tg3: Convert PHY_ADDR => TG3_PHY_MII_ADDR
This patch renames the PHY_ADDR preprocessor definition.  The following
patch will identify a new member on the MDIO bus, so we want this
preprocessor definition to be a little more descriptive.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-02 23:39:01 -08:00
Matt Carlson
f40386c845 tg3: Fix disappearing 57780 devices
Under certain power saving conditions, 57780 asic rev devices might
disappear from the system.  The fix is to disallow the PCIe PLL from
powering down.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-02 23:39:00 -08:00
Matt Carlson
92c6b8d16a tg3: Fix 5906 transmit hangs
The 5906 has trouble with fragments that are less than 8 bytes in size.
This patch works around the problem by pivoting the 5906's transmit
routine to tg3_start_xmit_dma_bug() and introducing a new SHORT_DMA_BUG
flag that enables code to detect and react to the problematic condition.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-02 23:39:00 -08:00
Matt Carlson
0e1406dd40 tg3: Assign flags to fixes in start_xmit_dma_bug
This patch adds a flag for each bug workaround in
tg3_start_xmit_dma_bug().  This is prep work for the following patch.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-02 23:38:58 -08:00
Matt Carlson
24bb4fb6da tg3: Fix phylib locking strategy
Felix Radensky noted that chip resets were generating stack trace dumps.
This is because the driver is attempting to acquire the mdio bus mutex
while holding the tp->lock spinlock.  The fix is to change the code such
that every phy access takes the tp->lock spinlock instead.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 03:37:39 -07:00
Eric Dumazet
bf18a9f8b3 tg3: Remove prev_vlan_tag from struct tx_ring_info
prev_vlan_tag field is not used.

Patch saves 512*8 bytes per tx queue ring on 64bit arches.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Matthew Carlson <mcarlson@broadcom.com>
2009-10-01 14:37:34 -07:00
Matt Carlson
882e9793fa tg3: Add MDIO bus address assignments
The 5717 is a dual port chip that has a shared MDIO bus design.  While
it is impossible for one function to interface with the wrong phy, that
function still needs to know which MDIO bus address to use when
interfacing with its own phy.  This patch adds code to determine which
MDIO bus address to use.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:44:09 -07:00
Matt Carlson
a1b950d56d tg3: Add 5717 NVRAM detection routines
This patch adds NVRAM detection routines for the 5717.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:44:06 -07:00
Matt Carlson
f6eb9b1fc1 tg3: Add 5717 asic rev
This patch adds the 5717 asic rev.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:44:01 -07:00
Matt Carlson
8d9d7cfc0e tg3: Assign rx ret producer indexes by vector
When RSS is enabled, the status block format changes slightly.  The
"rx_jumbo_consumer", "reserved", and "rx_mini_consumer" members get
mapped to the other three rx return ring producer indexes.  This patch
introduces a new per-interrupt member which identifies which location
in the status block a particular vector should look for return ring
updates.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:43:58 -07:00
Matt Carlson
baf8a94a57 tg3: Add RSS support
This patch adds code needed to enable RSS.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:43:49 -07:00
Matt Carlson
b6080e1260 tg3: Add coalesce parameters for msix vectors
This patch adds code to tune the coalescing parameters for the other
msix vectors.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:43:46 -07:00
Matt Carlson
fe5f5787f0 tg3: Add TSS support
This patch exposes the additional transmit rings to the kernel and makes
the necessary modifications to transmit, open, and close paths.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:43:44 -07:00
Matt Carlson
f77a6a8e6c tg3: Add tx and rx ring resource tracking
This patch adds code to assign status block, tx producer ring and rx
return ring resources needed for the other interrupt vectors.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:43:39 -07:00
Matt Carlson
679563f47c tg3: Add MSI-X support
This patch adds MSI-X support.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:43:33 -07:00
Matt Carlson
4f125f42dd tg3: Add support code around kernel interrupt API
This patch adds code to support multiple interrupt vectors around the
kernel's interrupt API.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:43:30 -07:00
Matt Carlson
fd2ce37f8e tg3: Add per-int coalesce now member
Each interrupt vector has its own bit in the host coalescing register to
force that vector's status block to be updated and generate an
interrupt.  This patch adds a member to the per-interrupt structure
that records which bit belongs to that vector.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 00:43:25 -07:00
Matt Carlson
f3f3f27e5b tg3: Move per-int tx members to a per-int struct
This patch moves the tx_prod, tx_cons, tx_pending, tx_ring, and
tx_buffers transmit ring device members to a per-interrupt structure.
It also adds a new transmit producer mailbox member (prodmbox) and
converts the code to use it rather than a preprocessor constant.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:43:04 -07:00
Matt Carlson
723344820a tg3: Move per-int rx members to per-int struct
This patch moves the rx_rcb, rx_rcb_mapping, and rx_rcb_ptr return ring
device members to a per-interrupt structure.  It also adds a new return
ring consumer mailbox register member (consmbox) and converts the code
to use it rather than a preprocessor constant.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:43:03 -07:00
Matt Carlson
898a56f8d8 tg3: Move general int members to a per-int struct
This patch moves the last_tag, last_tag_irq, and hw_status device
members to a per-interrupt structure.  It also adds a new interrupt
mailbox member (int_mbox) and converts the code to use it rather than a
direct preprocessor constant.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:43:01 -07:00
Matt Carlson
8ef0442f98 tg3: Move napi to per-int struct
This patch creates a per-interrupt data structure, moves the napi
member over, and creates a tg3 pointer back to the device structure.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:42:56 -07:00
Matt Carlson
79ed5ac7dd tg3: Use ext rx bds
The 5717 only uses extended buffer descriptors for the jumbo producer
ring.  Extended buffer descriptors are available on all devices that
support a separate jumbo producer ring so make the change universal.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:42:52 -07:00
Matt Carlson
21f581a536 tg3: Create a new prodring_set structure
This patch migrates most of the rx producer ring variables to a new
tg3_rx_prodring_set structure and modifies the code accordingly.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:42:50 -07:00
Matt Carlson
287be12e17 tg3: Clarify rx buffer relationships
This patch attempts to document the various rx buffer sizes used by the
driver and how they relate to each other.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:42:43 -07:00
Matt Carlson
8f666b07ac tg3: Move the JUMBO_CAPABLE and SUPPORT_MSI flags
This patch moves where the jumbo capable and msi support flags are
located.  This is prep work for the addition of msix support flags.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:42:41 -07:00
Matt Carlson
2befdcea96 tg3: Add new 5785 10/100 only device ID
This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-29 15:42:31 -07:00
Matt Carlson
7f97a4bd47 tg3: Convert code to use PHY_IS_FET
This patch converts the code to use the PHY_IS_FET flag rather than the
ASIC revision to decide whether or not to use FET paths.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26 15:48:00 -07:00
Matt Carlson
535ef6e112 tg3: Create MII_TG3_FET namespace
Broadcom's phys come in two distinctly different register layouts.  For
the lack of an official term to distinguish between the two formats, we
can loosely categorize them by their fast ethernet or gigabit ethernet
transceiver description.  This patch creates the (driver-internal) Fast
Ethernet Transceiver (FET) namespace and converts the 5906 EPHY
definitions over.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26 15:47:58 -07:00
Matt Carlson
bb85fbb6a9 tg3: Tune 5785 clock switching
This patch tunes the timeouts the CPMU uses to decide when to switch
from the clocks output by the PHY to internal clock sources.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26 15:47:56 -07:00
Matt Carlson
5e7ccf2003 tg3: Add 57788, remove 57720
This patch adds support for the 57788 and removes support for the 57720
which was never released.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26 15:47:53 -07:00
Matt Carlson
255ca311b6 tg3: Prevent tx BD corruption
This patch prevents a tx BD corruption bug by preventing the device from
powering down the PLL from L1 if the link speed is 10Mbps or 100Mbps.

The same bits are also used to prevent a system hang during chip reset
resulting from a complicated set of events that ultimately leads to
PCIe block register corruption.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26 15:47:47 -07:00
Matt Carlson
521e6b90dd tg3: Fix 57780 asic rev PCIe link receiver errors
This patch fixes some PCIe link receiver errors by decreasing the internal
electrical idle timeout.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-26 15:47:45 -07:00