Fix panic in lpfc_get_stats()
Symptoms: Panic on sysfs stats access
Cause: In lpfc_get_stats() we are writing to memory that we do not
own.
Fix: Fix our stats structure allocation. Embed phba->link_stats in
struct lpfc_hba and stop treating it like rogue structure.
Note: Embedding midlayer/transport structure in our structure caused
need for more files to include midlayer/transport headers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clear task management bits when preparing SCSI commands
In lpfc_scsi_prep_cmnd, clear the task management bits (fcpCntl2 member
in the fcp_cmd structure) when preparing regular SCSI commands.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic on lip and cable pull
Symptoms: Panic on lip or cable pull
Cause: Use after free of nlp in lpfc_nlp_remove()
Fix: Do not make FC transport calls after a node is removed. Transport
calls are disabled by ignoring the initial delete transition.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IOCB BDE not getting fully initialized during reuse
Symptoms: Driver gets Status 3 and Reason 0x13 on IOCB completions.
Cause: The IOCB bpl.bdeSize and bdeFlags are not getting initialized on reuse.
Fix: Reinitialize these fields in prep_dma each time an IOCB is used.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Steve Wilcox <spwilcox@att.com>
In order to properly report LUN's > 7, the DEC HSG80 definition in
scsi_devinfo.c needs to include BLIST_REPORTLUN2 rather than
BLIST_SPARSELUN. I've tested this change with several HSG firmware
revisions and with both Emulex and Qlogic HBA's.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a spurious (and illegal since it's marked __exit) call to
ahc_linux_exit() in ahc_linux_init() which causes a double list
deletion of the transport class; remove it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When run on a kernel that scans all LUNs, a certain crappy
scsi scanner reports the same LUN over and over..
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=155457
Aparently they were so shamed by this, they chose to remain
anonymous. Though it seems the blacklist code handles
anonymous vendors just fine.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
This patch adds the product ID for the ICP9067MA adapter.
The entries for the ICP9085LI, ICP5085BR, IBM8k & ASR4810SAS were
incorrect and would not initialize the adapters correctly.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There are certain rogue devices (and the aic7xxx driver) that return
BUSY or QUEUE_FULL forever. This code will apply a global timeout (of
the total number of retries times the per command timer) to a given
command. If it is exceeded, the command is completed regardless of its
state.
The patch also removes the unused field in the command: timeout and
timeout_total.
This solves the problem of detecting an endless loop in the mid-layer
because of BUSY/QUEUE_FULL bouncing, but will not recover the device.
In the aic7xxx case, the driver can be recovered by sending a bus reset,
so possibly this should be tied into the error handler?
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I have rediffed the patch against 2.6.13-rc5, done a couple of cosmetic
cleanups, and run some tests. Brian King has acknowledged that it fixes the
problems he has seen. Seems mature enough for inclusion into 2.6.14 (or
later)?
Nate's explanation of the changes:
I've attached patches against 2.6.13rc2. These are basically identical
to my earlier patches, as I found that all issues I'd seen in earlier
kernels still existed in this kernel.
To summarize, the changes are: (more details in my original email)
- add a kref to the scsi_tape structure, and associate reference
counting stuff
- set sr_request->end_io = blk_end_sync_rq so we get notified when an IO
is rejected when the device goes away
- check rq_status when IOs complete, else we don't know that IOs
rejected for a dead device in fact did not complete
- change last_SRpnt so it's set before an async IO is issued (in case
st_sleep_done is bypassed)
- fix a bogus use of last_SRpnt in st_chk_result
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The cmd->timeout field has been obsolete for a while now. While looking
to remove it, I came across this use in the aacraid driver. It looks
like you want to initialise the firmware with the current timeout of the
command (in seconds), so the value I think you should be using is
cmd->timeout_per_command.
Acked by: Mark Haverkamp <markh@osdl.org>
Acked by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
without it you get this failure:
drivers/built-in.o(.text+0xdcccd): In function `ahd_linux_slave_configure':
drivers/scsi/aic7xxx/aic79xx_osm.c:636: undefined reference to `spi_dv_device'
drivers/built-in.o(.text+0xdd7b1): In function `ahd_send_async':
drivers/scsi/aic7xxx/aic79xx_osm.c:1652: undefined reference to `spi_display_xfer_agreement'
drivers/built-in.o(.init.text+0x7b4d): In function `ahd_linux_init':
drivers/scsi/aic7xxx/aic79xx_osm.c:2765: undefined reference to `spi_attach_transport'
drivers/built-in.o(.init.text+0x7c94):drivers/scsi/aic7xxx/aic79xx_osm.c:2774: undefined reference to `spi_release_transport'
drivers/built-in.o(.exit.text+0x72c): In function `ahd_linux_exit':
drivers/scsi/aic7xxx/aic79xx_osm.c:2783: undefined reference to `spi_release_transport'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
This patch adds support for the new raw io command. This new command
offers much larger io commands, is more friendly to the internal firmware
structure requiring less translation efforts by the firmware and offers
support for targets greater than 2TB (patch to support >2TB will
be sent in the future).
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
If the Adapter is quiet and does not produce an AIF event packets to be
picked up by the management applications for longer than the timeout
interval of two minutes, the cleanup code that deals with aging out
registrants could erroneously drop the registration. The timeout is
there to clean up should the management application die and fail to poll
for updated AIF event packets.
Moving the timer update from the ioctl code that delivers an AIF to the
polling registrant to the bottom of the ioctl means the timeout is reset
with any management application polling activity regardless if an AIF is
delivered or not removing the erroneous timeout cleanups.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
This patch removes the duplicate code in the write_callback command
completion handler, and renames read_callback to io_callback. Optimized
the lba calculation into the debug print routine macro to optimize the
i/o code path.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add in pci shutdown method so that the adapter shuts down correctly and
flushes its cache. Shutdown should also disable the adapter's interrupt
when shutdown (in particularly if the driver is rmmod'd) to prevent
spurious hardware activities.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
Fixes a bug in check_revision. It should return the driver version not
the firmware version.
Update driver version number.
Update driver version string.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
If more than two commands are outstanding to the controller, there is no
need to notify the adapter via a PCI bus transaction of additional
commands added into the queue; it will get to them when it works through
the produce/consumer indexes.
This reduced the PCI traffic in the driver to submit a command to the
queue to near zero allowing a significant number of commands to be
turned around with no need to block for the PCI bridge to flush the
notify request to the adapter.
Interrupt mitigation has always been present in the driver; it was
turned off because of a bug that prevented one from realizing the
usefulness of the feature. This bug is fixed in this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch upports all relevant code fixes and bumps the driver version
to 7.0 to signify starting a new tree.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
this patch is just a cross-port of the fixup for aic7xxx DT settings.
As the same restrictions apply for aic79xx also (DT requires wide
transfers) the dt setting routine should be modified equivalently.
And an invalid period setting will be caught by ahd_find_syncrate()
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This parameter is important only to people who take the time to tune the
margin control settings, otherwise it's completely irrelevant. However,
just in case anyone should want to do this, it's appropriate to include
the parameter.
I don't do anything with it in DV by design, so the parameter will come
up as off by default, so if anyone actually wants to play with the
margin control settings they'll have to enable it under the
spi_transport class first.
I also updated the transfer settings display to report all of the PPR
settings instead of only DT, IU and QAS
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a slight problem in the way you've done the transport
parameters; reading from the variables actually produces the current
settings, not the ones you just set (and there's usually a lag because
devices don't renegotiate until the next command goes over the bus). If
you set the bit immediately, you get into the situation where the
transport parameters report something as being set even if the drive
cannot support it.
I patched the driver to do it this way and also corrected a panic in the
proc routines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates various scsi_transport_spi parameters with the actual
parameters used by the driver internally.
Domain Validation for all devices should now work properly.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the aic79xx driver to take advantage of the
scsi_transport_spi infrastructure. Patch is quite a mess as some
procedures have been reshuffled to be closer to the aic7xxx driver.
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Jeff Garzik <jgarzik@pobox.com>
This patch removes the busyq in aic79xx and uses the command-queue from
the midlayer instead. Additionally some dead code is removed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Fixed rejections
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
we have the most recent microcode, make sure to always load it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support to not allow additions to a host when it is being removed.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove the old scsi_host_cancel function as it has not been working for
sometime do to the device list possibly being empty when it is called and
possible race issues. Add setting of SHOST_CANCEL at the state of beginning
of scsi_remove_host.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Migrate the current SCSI host state model to a model like SCSI
device is using.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It seems very unlikely that this driver will go into any stable kernel
before devfs will be removed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
aic doesnt work anymore after this change which appeared int 2.6.13-rc1:
[SCSI] aic7xxx/aic79xx: remove useless byte order macro cruft
2 files did not include byteorder.h, aic died with panic
"Unknown opcode encountered in seq program"
This patch fixes it for me.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When leaving S3 state, the AGP bridge may not have all PCI configuration
registers set in the same way as they were at boot. This should be fixed
by pci_restore_state - however, the APBASE register cannot be set to
conflict with the APSIZE register. If APSIZE is larger than it was before
suspend, pci_restore_state will not restore APBASE correctly. The attached
patch adds an extra item to the agp_bridge_data structure and uses it to
store the value of APBASE. On resume, this is then written after APSIZE
has been set. This patch only touches the path used for Intel chipsets
without integrated graphics, and may need to be extended to work with the
others.
Without this patch, I get the symptoms described in bug 4921 - APBASE ends
up overlapping various PCI devices, and as a result they fail to work after
resume.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Close a small window where a device may be not operational again after senseid
finished and the "same device" check fails due to dev=0000 by checking for dnv
after stsch() by then setting the device to not operational. (No need to
check for dnv in ccw_device_handle_oper() again since we don't do stsch() into
the subchannel's schib in the meantime and will get a crw anyway if the device
becomes not oper again).
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch that introduced waiting for interrupts after resetting the reader
can cause the boot to fail because the system is waiting for an interrupt that
will never arrive. Add code to check if an interrupt is supposed to arrive
before waiting endlessly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The #if/#ifdef cleanup exposed a bug in UML's ELF header processing. With
this bug fixed, UML recognizes the vsyscall info coming from the host. On
FC4, there is a vsyscall page low in the address space, which UML doesn't
provide. This causes an infinite page fault loop and a hang on boot.
This patch works around that by making this look like a no-vsyscall system.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use memcpy in fb_pad_aligned_buffer. It is suboptimal because only
a few bytes are moved at a time. Replace with a for-loop.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device. The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided. Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up. The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices. The patch corrects this
problem by allowing PCI IRQs below 16.
Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
