Commit graph

1776 commits

Author SHA1 Message Date
Oliver Neukum
b98b98f97c USB: power management for kaweth
- implements suspend when the network interface is down
- fixes a typo in comments
- adds debugging output for power management
- fixes a compiler warning

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:35 -08:00
Phil Endecott
511779fd9e usb: gadgetfs remove delayed init mode
Gadgetfs had a mode in which endpoint descriptors were written by the user
program before connection.  This mode had some bugs, and hasn't seen much
(if any) use.  This patch removes that mode, leaving the mode of operation
where the user program waits for endpoint 0 to report a SET_CONFIGURATION,
and only then configures the endpoints.

From: "Phil Endecott" <spam_from_usb_devel@chezphil.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:35 -08:00
David Brownell
2505107def usb: gadgetfs whitespace cleanup
Remove some whitespace bugs in gadgetfs (mostly from someone's
patch updating the AIO support).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:35 -08:00
Marc Pignat
6dde896e4e USB: ohci-at91 refcount fix for irq wake enables
The attached patch fixes the unbalanced calls to enable_irq_wake() and
disable_irq_wake() in the AT91 USB Host driver.

It should resolve these kernel messages:
  Unbalanced IRQ x wake disable
  BUG: warning at kernel/irq/manage.c:167/set_irq_wake()

(The original code was debugged before a bug in the genirq wakeup irq
logic was fixed by adding the IRQ wake enable/disable refcounting.
Not all code yet uses the bugfixed model.)

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:35 -08:00
Alan Stern
f3f4906516 usb-storage: SCSI level fixes
This patch (as835) removes from usb-storage the code which sets all
devices to a SCSI level of at least SCSI-2.  The original reasons for
doing this no longer apply, and in fact it prevents certain kinds of
ATA pass-thru commands from being used.

The patch also marks CB and CBI devices that are SCSI-0 (legacy SCSI)
as being single-LUN, since the combined SCSI-over-USB transport
protocol has no way to convey LUN information to these devices.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:35 -08:00
Alan Stern
85a975d0ce UHCI: no dummy TDs for Iso QHs
Isochronous queues don't need a dummy TD because the Queue Header
isn't managed by the hardware.  This patch (as836) removes the
unnecessary dummy TDs.

The patch also fixes a long-standing typo in a comment (a "don't" was
missing -- potentially very confusing!).

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:35 -08:00
Alan Stern
f3fe239b67 UHCI: improved debugging checks for the frame list
This patch (as768) improves the debugging checks for the uhci-hcd
frame list.  The number of entries displayed is limited to 10, and the
driver now checks for the correct Skeleton QH link value at the end of
each chain of Isochronous TDs.  The code to compute these link values
is now used in two spots, so it is moved into its own separate
subroutine.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:35 -08:00
Oliver Neukum
f38649fee9 USB: race on disconnect in mdc800
I overlooked one. Setting the flag and killing the URBs must be under the lock
so that no URB is submitted after usb_kill_urb()

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:34 -08:00
Pete Zaitcev
6f23ee1fef USB: add binary API to usbmon
This patch adds a new, "binary" API in addition to the old, text API usbmon
had before. The new API allows for less CPU use, and it allows to capture
all data from a packet where old API only captured 32 bytes at most. There
are some limitations and conditions to this, e.g. in case someone constructs
a URB with 1GB of data, it's not likely to be captured, because even the
huge buffers of the new reader are finite. Nonetheless, I expect this new
capability to capture all data for all real life scenarios.

The downside is, a special user mode application is required where cat(1)
worked before. I have sample code at http://people.redhat.com/zaitcev/linux/
and Paolo Abeni is working on patching libpcap.

This patch was initially written by Paolo and later I tweaked it, and
we had a little back-and-forth. So this is a jointly authored patch, but
I am submitting this I am responsible for the bugs.

Signed-off-by: Paolo Abeni <paolo.abeni@email.it>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:34 -08:00
John Daiker
7ca46b862f USB Gadget file_storage.c: remove unnecessary casts
Went looking through some usb stuff and found some unnecessary casts in
file_storage.c  This is part of the KernelJanitors TODO list.

Signed-off-by: John Daiker <daikerjohn@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:34 -08:00
Johannes Hölzl
52d67f0b5c USB: Bugfix for aircable: Add module and name to usb_serial_driver
While adding the dynamic-id support to usb serial I found a small bug in
the air cable driver:

Adds module and name information to the usb_serial_driver instance
of aircable. So the aircable driver is correctly shown under
/sys/bus/usb-serial/drivers/aircable and has the module link.

Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:34 -08:00
Johannes Hölzl
d9b1b78773 USB serial: add driver pointer to all usb-serial drivers
Every usb serial driver should have a pointer to the corresponding usb driver.
So the usb serial core can add a new id not only to the usb serial driver, but
also to the usb driver.

Also the usb drivers of ark3116, mos7720 and mos7840 missed the flag
no_dynamic_id=1. This is added now.

Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:34 -08:00
Greg Kroah-Hartman
93bacefc4c USB serial: add dynamic id support to usb-serial core
Thanks to Johannes Hölzl <johannes.hoelzl@gmx.de> for fixing a few
things and getting it all working properly.

This adds support for dynamic usb ids to the usb serial core.  The file
"new_id" will show up under the usb serial driver, not the usb driver
associated with the usb-serial driver (yeah, it can be a bit confusing
at first glance...)

This patch also modifies the USB core to allow the usb-serial core to
reuse much of the dynamic id logic.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
2007-02-07 15:44:33 -08:00
Sylvain Munaut
495a678fc6 ohci: Add support for OHCI controller on the of_platform bus
PPC embedded systems can have a ohci controller builtin. In the
new model, it will end up as a driver on the of_platform bus,
this patches takes care of them.

Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:33 -08:00
Sylvain Munaut
5e16fabe5d ohci: Rework bus glue integration to allow several at once
The previous model had the module_init & module_exit function in the
bus glue .c files themselves. That's a problem if several glues need
to be selected at once and the driver is built has module. This case
is quite common in embedded system where you want to handle both the
integrated ohci controller and some extra controller on PCI.

The ohci-hcd.c file now provide the module_init & module_exit and
appropriate driver registering/unregistering is done conditionally,
using #ifdefs.

Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:33 -08:00
Ole Andre Vadla Ravnas
ad55d71a3d rndis_host learns ActiveSync basics
Windows Mobile 5 based devices described as supporting "ActiveSync":

 - Speak RNDIS but lack the CDC and union descriptors.  This patch
   updates the cdc ethernet code to fake ACM descriptors we need.

 - Require RNDIS_MSG_QUERY messages to include a buffer of the size the
   response should generate.  This patch updates the rndis host code to
   pass this will-be-ignored data.

The resulting RNDIS host code has been reported to work with several
WM5 based devices.

(Note that a fancier patch is available at synce.sf.net.)


Some bugfixes, affecting not just ActiveSync:
    (a)	when cleaning up after RNDS init fails, scrub the second interface
	just like cdc_ether does, so disconnect won't oops.
    (b)	handle peripherals that use the pad-to-end-of-packet option; some
	devices can't talk to us if that option doesn't work.
    (c)	when choosing configurations, don't forget about an RNDIS config
	just because the RNDIS driver is dynamically linked.

Cleanup, streamlining, bugfixes, Kconfig, and matching hub driver update.
Also for paranoia's sake, refuse to talk to something that looks like a
real modem instead of RNDIS.

Signed-off-by: Ole Andre Vadla Ravnaas <oleavr@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:33 -08:00
David Brownell
11d5489873 USB: ethernet gadget interop with MCCI Windows driver
It turns out that minor tweaks to the "CDC Subset" support in the Ethernet
gadget driver, just updating a config descriptor, let it be automagically
recognized by a Windows driver supported by MCCI.

This patch adds those descriptors, so systems using PXA 255 processors
(like Gumstix etc) can interop with those commercial MS-Windows drivers.
This is a Good Thing since Microsoft's RNDIS code has bugginess issues,
which are unfortunately compounded by "won't fix" issues as well as "the
published specs are incomplete and wrong" issues.  Being able to talk to
the MCCI driver gives Windows users another connectivity option.  (MCCI
also has CDC Ethernet drivers, which can help most non-PXA processors.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:33 -08:00
Alan Stern
1737bf2c5e usbcore: remove unneeded error check
This patch (as830) removes some unnecessary error checking.  According
to the kerneldoc, schedule_work() can't fail.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:33 -08:00
David Brownell
2360e4aa64 USB: indicate active altsetting in proc/bus/usb/devices file
Update /proc/bus/usb/devices output to report active altsettings.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:33 -08:00
Dan Carpenter
316547fdfa USB: devio.c add missing INIT_LIST_HEAD()
It should hopefully fix the list corruption bug on:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=214402

Add a missing INIT_LIST_HEAD()

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:33 -08:00
Oliver Neukum
2cba72f025 USB: mutexification of rio500
this makes the rio500 misc usb driver use mutexes and turns uninterruptible
sleep into interruptible sleep where the semantics are not affected.

Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:32 -08:00
Tobias Klauser
4727810705 USB: Remove unneeded void * casts in idmouse.c
The patch removes unneeded void * casts for the following (void *) pointers:
- struct file: private_data

The patch also contains some whitespace and coding style cleanups in the
relevant areas.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:32 -08:00
David Brownell
5f84813774 USB: <linux/usb_ch9.h> becomes <linux/usb/ch9.h>
This moves <linux/usb_ch9.h> to <linux/usb/ch9.h> to reduce some of the
clutter of usb header files.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:32 -08:00
Benjamin Herrenschmidt
d728e327d4 USB: Fix EHCI warning
This patch fixes a warning introduced by the big endian MMIO EHCI
support patch on platforms that don't have readl_be/writel_be variants
(though mostly harmless as those are called in an if (0) statement,
but gcc still warns).

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2007-02-07 15:44:32 -08:00
Benjamin Herrenschmidt
b32e904d54 USB: Fix OHCI warning
This patch fixes a warning introduces by the split endian OHCI support
patch on platforms that don't have readl_be/writel_be variants (though
mostly harmless as those are called in an if (0) statement, but gcc
still warns).

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:32 -08:00
Benjamin Herrenschmidt
083522d766 USB: Implement support for EHCI with big endian MMIO
This patch implements supports for EHCI controllers whose MMIO
registers are big endian and enables that functionality for
the Toshiba SCC chip. It does _not_ add support for big endian
in-memory data structures as this is not needed for that chip
and I hope it will never be.

The guts of the patch are to convert readl(...) to
ehci_readl(ehci, ...) and similarly for register writes.

Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:32 -08:00
Benjamin Herrenschmidt
11d1a4aa8d USB: Implement support for "split" endian OHCI
This patch separates support for big endian MMIO register access
and big endian descriptors in order to support the Toshiba SCC
implementation which has big endian registers but little endian
in-memory descriptors.

It simplifies the access functions a bit in ohci.h while at it.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:31 -08:00
Benjamin Herrenschmidt
4302a595cd USB: Rework the OHCI quirk mecanism as suggested by David
This patch applies David Brownell's suggestion for reworking the
OHCI quirk mechanism via a table of PCI IDs. It adapts the existing
quirks to use that mechanism.

This also moves the quirks to reset() as suggested by the comment
in there. This is necessary as we need to have the endian properly
set before we try to init the controller.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:31 -08:00
Greg Kroah-Hartman
0873c76485 USB: convert usb class devices to real devices
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:31 -08:00
Greg Kroah-Hartman
7bc3d63562 USB: move usb_device_class class devices to be real devices
This moves the usb class devices that control the usbfs nodes to show up
in the proper place in the larger device tree.

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:30 -08:00
Greg Kroah-Hartman
6e8cf7751f USB: add EPIC support to the io_edgeport driver
This patch adds EPiC support to the io_edgeport driver which adds
support for a number of NCR printers:
	- NCR (Axiohm) 7401-K580 printer
	- NCR (TEC) 7401-K590 printer, 7402-K592
	- NCR (TEC) 7167, 7168 printers
	- NCR (TEC) 7197, 7198, F306, F307, F309 printers
	- NCR (Axiohm) 7194 printer
	- NCR (Axiohm) 7158 printer
and a few more.

It is based on the 2.6.19 kernel.

Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
2007-02-07 15:44:30 -08:00
Luiz Fernando N. Capitulino
20b2e28fc5 USB: unusual_devs.h for Sony floppy
This patch increases the range for 0x054c:0x002c devices to make
the following Sony USB floppy to work:

T:  Bus=02 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=054c ProdID=002c Rev=20.00
S:  Manufacturer=SONY
S:  Product=USB Floppy
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=04 Prot=00 Driver=usb-storage
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   2 Ivl=127ms

Signed-off-by: Marcelo Ricardo Leitner <mrl@mandriva.com>
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 15:44:30 -08:00
Kay Sievers
f9f852df2f Driver core: add device_type to struct device
This allows us to add type specific attributes, uevent vars and
release funtions.

A subsystem can carry different types of devices like the "block"
subsys has disks and partitions. Both types create a different set
of attributes, but belong to the same subsystem.

This corresponds to the low level objects:
  kobject   -> device       (object/device data)
  kobj_type -> device_type  (type of object/device we are embedded in)
  kset      -> class/bus    (list of objects/devices of a subsystem)

Signed-off-by: Kay Sievers <kay.sievers@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 10:37:14 -08:00
Greg Kroah-Hartman
80f745fb1b USB: add the sysfs driver name to all modules
This adds the module name to all USB drivers, if they are built into the
kernel or not.  It will show up in /sys/modules/MODULE_NAME/drivers/

Cc: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 10:37:12 -08:00
YOSHIFUJI Hideaki / 吉藤英明
e77c2baf75 PEGASUS: Fix typo in Corega products.
s/FEter/FEther/.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-05 16:58:49 -05:00
YOSHIFUJI Hideaki / 吉藤英明
b29cf31d7e ASIX: Add IO-DATA ETG-US2 Support.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-05 16:58:49 -05:00
Soeren Sonnenburg
a417a21e10 USB HID: handle multi-interface devices for Apple macbook pro properly
Some HID devices by Apple have both keyboard and mouse interfaces; the
keyboard interface is handled by usbhid, but the mouse (really
touchpad) interface must be handled by the separate 'appletouch'
driver.  Using HID_QUIRK_IGNORE will make hiddev ignore both
interfaces, therefore a new quirk flag to ignore only the mouse
interface is required.

Signed-off-by: Soeren Sonnenburg <kernel@nn7.de>
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-02-05 10:06:01 +01:00
Jiri Kosina
43c7bf0472 USB HID: fix bogus comment in hid_get_class_descriptor()
The comment in hid_get_class_descriptor() says a very obvious thing
and is also violating codingstyle. Just remove it.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-02-05 10:00:43 +01:00
Jiri Kosina
8235ca3c05 USB HID: remove hid_find_field_by_usage()
The unused hid_find_field_by_usage() function has been commented out for
a pretty long time. Remove it completely.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-02-05 10:00:42 +01:00
Jiri Kosina
7c37914600 HID: API - fix leftovers of hidinput API in USB HID
hidinput_{open,close}() functions do not belong to usbhid, but
to the generic HID layer. Move them, and fix hooks in struct
hid_device, so that now the callbacks are done to transport-specific
_open() functions, but not input_open() functions.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-02-05 10:00:40 +01:00
Jiri Kosina
c080d89ad9 HID: hid debug from hid-debug.h to hid layer
hid-debug.h contains a lot of code, and should not therefore
be a header.

This patch moves the code to generic hid layer as .c source, and
introduces CONFIG_HID_DEBUG to conditionally compile it, instead
of playing with #define DEBUG and including hid-debug.h.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-02-05 10:00:38 +01:00
Anssi Hannula
20eb127906 hid: force feedback driver for PantherLord USB/PS2 2in1 Adapter
Add a force feedback driver for PantherLord USB/PS2 2in1 Adapter,
0810:0001. The device identifies itself as "Twin USB Joystick".

Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-02-05 10:00:05 +01:00
Anssi Hannula
5556feae1c hid: quirk for multi-input devices with unneeded output reports
Add new quirk HID_QUIRK_SKIP_OUTPUT_REPORTS to skip output reports
when enumerating reports on a hid-input device. Add this quirk and
HID_QUIRK_MULTI_INPUT to 0810:0001.

PantherLord Twin USB Joystick, 0810:0001 has separate input reports
for 2 distinct game controllers in the same interface, so it needs
HID_QUIRK_MULTI_INPUT. However, the device also contains one output
report per controller which is used to control the force feedback
function, and we do not want those to appear as separate input
devices as well. The simplest approach seems to be to add a quirk to
skip output reports on 0810:0001, and allow the force feedback
driver to handle those.

Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-02-05 10:00:04 +01:00
Anssi Hannula
c4146067fd hid: allow force feedback for multi-input devices
Allow hid devices with HID_QUIRK_MULTI_INPUT to have force feedback.
This was previously disabled because there were not any force
feedback drivers for such devices. This will change with my upcoming
patch.

Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-02-05 10:00:02 +01:00
Al Viro
886ae1fa13 [PATCH] fix rtl8150
That code doesn't do what its author apparently thought it would do...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-03 20:37:37 -08:00
Jiri Kosina
76398f9667 HID: fix pb_fnmode and move it to generic HID
The apple powerbook people are used to switch the pb_fnmode
setting at runtime through writing to sysfs, altering the
module parameter value. This was broken for them in 2.6.20-rc1
when generic HID layer was introduced, as the pb_fnmode flag
was made per-hiddevice, instead of global variable.

This patch moves the pb_fnmode module parameter from usbhid module
to hid module, but apart from that retains backward compatibility
with respect to changing the mode through sysfs.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-01-30 15:05:27 +01:00
Jiri Kosina
ad2905f065 USB HID: fix hid_blacklist clash for 0x08ca/0x0010
commit d8c8a39316 introduced a clash in
hid_blacklist for 0x08ca/0x0010 (GTCO vs. AIPTEK). As the vendor of
GTCO device doesn't seem to be interested in supporting their legacy
HW with this conflicting ids, it is OK to remove it.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-01-25 18:31:23 +01:00
Al Viro
c3ea6729fe [PATCH] funsoft: ktermios fix
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-01-23 11:09:49 -08:00
Manuel Osdoba
39559b4ff8 USB: unusual_devs.h entry for nokia 6233
In appendix a patch for the nokia 6233 mobile phone is included.
The patch is against 2.6.20-rc5. It is my first patch. Hopefully it has
the right format. The code makes my nokia 6233 on my computer work.


From: Manuel Osdoba <manuel.osdoba@tu-ilmenau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-22 11:55:17 -08:00
Petr Stetiar
caaf26325d USB: Fix for typo in ohci-ep93xx.c
Attached patch fixes typo in USB driver reported by Chase Douglas on linux-cirrus mailing
list. http://www.freelists.org/archives/linux-cirrus/12-2006/msg00003.html

Signed-off-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-22 11:55:17 -08:00
Greg Kroah-Hartman
b1bf4f412b USB: disable USB_MULTITHREAD_PROBE
Disable the USB_MULTITHREAD_PROBE option because it causes crashes on
people's machines and they never remember to actually read the config
help files.

No one likes this, everyone hates it, I'm going to go eat worms...

The full logic will be ripped out later.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-22 11:55:17 -08:00
garrett_damore@tadpole.com
53e8f84dc6 USB: add vendor/device id for Option GT Max 3.6 cards
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=7814


Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-22 11:55:16 -08:00
Pete Zaitcev
379885a9b2 USB: unusual_devs.h for 0x046b:ff40
American Megatrends did something wrong in their floppy emulator. It breaks
with both kinds of MODE SENSE which our stack sends. Alan and I tried a few
tweaks, and got LUNs sensed right, but US_FL_NO_WP_DETECT is still needed.

I set the firmware bracket to 1.00 exactly, in case AMI or Sun fix it with a
firmware update. Hey, you never know.

Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-22 11:55:16 -08:00
Oliver Neukum
8d2bad8788 USB: make usbhid ignore Imation Disc Stakka
on request of the sourceforge project for this device, a kind of
robotized CD storage, it should be ignored by the generic driver.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-22 11:55:16 -08:00
Daniel Gollub
deb31f1764 USB: rndis_host: fix crash while probing a Nokia S60 mobile
Bug fix for driver rndis_host which fixes rndis_host probing certain
Nokia S60 (Series 60) mobiles. While the rndis_host get probed by usbnet
and tries to bind the Nokia mobile the bind is going to fail. The
rndis_host module tries to release the device, in a wrong way, which
cause the oops.

Fixes Bugzilla #7201

Signed-off-by: Daniel Gollub <dgollub@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-22 11:46:55 -08:00
Andres Salomon
d0ffff8fdd USB: asix: Detect internal PHY and enable/use accordingly
Different AX88772 dongles use different PHYs; the chip is capable of using
both a primary and secondary PHY, and supports an internal and external PHY.

It appears that some DUB-E100 devices use the internal PHY, so trying to use
an external one will not work (note that this is different across revisions,
as well; the "A" and "B" revs of the DUB-E100 use different PHYs!).  The data
sheet for the AX88772 chip specifies that the internal PHY id will be 0x10,
so if that's read from the EEPROM, we should use that rather than attempting
to use an external PHY.

Thanks to Mitch Bradley for pointing this out!

Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: David Hollis <dhollis@davehollis.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-22 11:46:55 -08:00
Daniel Ritz
c9d8c2b324 usbtouchscreen: make ITM screens report BTN_TOUCH as zero when not touched
ITM screens send invalid x/y data when not touched. this was fixes a while ago
but the problem is if the screen is not touched anymore the driver never does
not report BTN_TOUCH as zero. fix it by sending the report with the last valid
coordinates when pressure is released.

Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: J.P. Delport <jpdelport@csir.co.za>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-22 11:46:55 -08:00
Jeremy Roberson
d8c8a39316 hid-core.c: Adds GTCO CalComp Interwrite IPanel PIDs to blacklist
Adds GTCO CalComp Interwrite IPanels to the hid-core.c blacklist.

Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-01-21 22:18:03 +01:00
Anssi Hannula
be8209753b HID: put usb_interface instead of usb_device into hid->dev to fix udevinfo breakage
The commit 4916b3a57f introduced a
hid regression between 2.6.19 and 2.6.20-rc1. The device put in
input_dev->cdev is now of type usb_device instead of usb_interface.

Before:
> # readlink -f /sys/class/input/input6/event4/device
> /sys/devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.1
After:
> # readlink -f /sys/class/input/input3/event3/device
> /sys/devices/pci0000:00/0000:00:10.0/usb1/1-1

This causes breakage:
> # udevinfo -q all -n /dev/input/event3
> P: /class/input/input3/event3
> N: input/event3
> S: input/by-path/pci-1-1--event-
> E: ID_SERIAL=noserial
> E: ID_PATH=pci-1-1-

No ID_MODEL, ID_VENDOR, ID_REVISION, ID_TYPE etc etc.

Fix this by assigning the intf->dev into hid->dev, and fixing
all the users.

Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-01-21 22:18:01 +01:00
Adrian Friedli
694400641b HID: GEYSER4_ISO needs quirk
I've got a newer MacBook with core2duo. Two keys on the keyboard are
swapped, "unswaping" works with the same trick as GEYSER3_ISO.

Signed-off-by: Adrian Friedli <masteradi@gmx.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-01-21 22:17:50 +01:00
Russell King
e7c4e1a58f HID: fix some ARM builds due to HID brokenness - make USB_HID depend on INPUT
We have USB_HID _newly_ selected in configurations which didn't
have it before, which overrides CONFIG_HID and builds HID without
input support.

Nevertheless, here's a patch to solve more of the same that my original
patch attempted to solve.  The original patch is still required.  Seems
to solve the final instance of this problem here.

Signed-off-by: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-01-21 22:17:47 +01:00
Jiri Slaby
285b0b62bc Input: hid-ff - add support for Logitech Momo racing wheel
Add support for Logitech Momo racing wheel (046d:ca03) to hid force
feedback.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2007-01-18 00:43:41 -05:00
David Miller
88bf7b391d [PATCH] really fix funsoft driver
Fix void cast and re-enable on sparc.

Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2007-01-11 18:18:21 -08:00
David Hollis
14e51f28ad USB: asix: Fix AX88772 device PHY selection
A small typo in ax88772_bind() prevents the device from selecting the
proper PHY, leaving the device useless.  The attached patch fixes this.
If this patch can be added to the 2.6.19.x series as well, that would be
helpful for end-users.

Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:10 -08:00
Martin Williges
4f45d0387b USB: usblp.c - add Kyocera Mita FS 820 to list of "quirky" printers
This patch gets the Kyocera FS-820 working with cups 1.2 via usb again. It
adds the printer to the list of "quirky" printers. The printer seems not
answer to ID requests some seconds after plugging in. Patch is based on
linux-2.6.19.1.

Background:
As far as I could see (strace, usbmon), the Kyocera FS-820 answers to ID
requests only a few seconds after plugging it in. This applies to detecting
it with cups and is also true for the printing itself, which is initiated
with an ID request. Since I have little usb knowledge, maybe someone can
interpret the data, especially the fist bulk transfer - why request 8192
bytes? This is the second version of the patch.

usbmon output of printing an email without patch:
tail -F /tmp/printlog.txt
c636e140 3374734463 S Bi:002:02 -115 8192 <
c9d43b40 3374734494 S Ci:002:00 s a1 00 0000 0000 03ff 1023 <
c9d43b40 3379732301 C Ci:002:00 -104 0
c636e140 3379733294 C Bi:002:02 -2 0
[...repeating...]

with patch:
tail -F /tmp/printlog.txt
d9cb82c0 3729790131 S Ci:002:00 s a1 00 0000 0000 03ff 1023 <
d9cb82c0 3729791725 C Ci:002:00 0 91 = 005b4944 3a46532d 3832303b 4d46473a
 4b796f63 6572613b 434d443a 50434c58 df956320 3732493190 S Bo:002:01 -115
 1347 = 1b252d31 32333435 5840504a 4c0a4050 4a4c2053 4554204d 414e5541
 4c464545 [...more data...]

Signed-off-by: Martin Williges <kernel@zut.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:10 -08:00
Andrew Morton
c067dfc650 sisusb_con warning fixes
x86_64:

drivers/usb/misc/sisusbvga/sisusb_con.c: In function 'sisusbcon_putc':
drivers/usb/misc/sisusbvga/sisusb_con.c:405: warning: cast from pointer to integer of different size
drivers/usb/misc/sisusbvga/sisusb_con.c: In function 'sisusbcon_putcs':
drivers/usb/misc/sisusbvga/sisusb_con.c:440: warning: cast from pointer to integer of different size
drivers/usb/misc/sisusbvga/sisusb_con.c: In function 'sisusbcon_clear':
drivers/usb/misc/sisusbvga/sisusb_con.c:494: warning: cast from pointer to integer of different size
drivers/usb/misc/sisusbvga/sisusb_con.c: In function 'sisusbcon_bmove':
drivers/usb/misc/sisusbvga/sisusb_con.c:566: warning: cast from pointer to integer of different size
drivers/usb/misc/sisusbvga/sisusb_con.c: In function 'sisusbcon_switch':
drivers/usb/misc/sisusbvga/sisusb_con.c:614: warning: cast from pointer to integer of different size
drivers/usb/misc/sisusbvga/sisusb_con.c: In function 'sisusbcon_scroll_area':
drivers/usb/misc/sisusbvga/sisusb_con.c:941: warning: cast from pointer to integer of different size

Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:10 -08:00
Sarah Bailey
c07be136a8 USB: Fixed bug in endpoint release function.
Error handling in usb_create_ep_files() is not correct unless
the minor number is freed in ep_device_release().

Signed-off-by: Sarah Bailey <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:09 -08:00
Pete Zaitcev
ad1428c96e USB storage: fix ipod ejecting issue
This patch from Pete fixes the 'ejecting problem' on yet another ipod. Please applyt.


Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:09 -08:00
Phil Dibowitz
f1cd4ad202 USB Storage: unusual_devs: add supertop drives
This combines patches from Alan Stern and Robert Schedel for two "Super Top"
drives that need the IGNORE_RESIDUE flag but have different vendor IDs.

Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:09 -08:00
David Brownell
e6a6e472f5 USB: omap_udc build fixes (sync with linux-omap)
Resync the omap_udc driver with the latest from the Linux-OMAP tree.
Changes include DMA API updates (it builds again!), clock/pm updates,
minor bugfixes, whitespace.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:09 -08:00
Andrew Morton
6a3c3d4952 USB: funsoft is borken on sparc
drivers/usb/serial/funsoft.c: In function `funsoft_ioctl':
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_iflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_iflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_iflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_oflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_oflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_oflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_lflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_lflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_lflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_line' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_line' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_line' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'

Cc: David Clare <david@funsoft.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:09 -08:00
Miguel Angel Alvarez
8c1527132c USB: fix interaction between different interfaces in an "Option" usb device
Just the serial port in the first interface should control DTR and RTS
lines. This way, the closing of the rest of the ports does not produce a=
hangup in the communication.

Signed-off-by: Miguel Angel Alvarez <ma.alvarez@ziv.es>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:08 -08:00
Alan Stern
25c77b3294 UHCI: support device_may_wakeup
This patch (as831) adds device_may_wakeup() support to uhci-hcd; it
has been lacking for a long time.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:08 -08:00
Alan Stern
c80a70d53f UHCI: make test for ASUS motherboard more specific
Instead of matching all motherboards whose name contains "A7V8X" for a
remote-wakeup hardware bug, this patch (as829) matches only those
boards whose name is exactly equal to "A7V8X".  Later motherboards
don't seem to have the bug.

(In fact, it's possible that only one motherboard in the world has the
bug.  With only one user reporting problems, it's hard to tell.)

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-01-05 12:19:08 -08:00
Jiri Kosina
69e4d94818 HID: fix help texts in Kconfig
The help text for CONFIG_HID might imply for someone that
it's necessary to enable it for any keyboard or mouse
attached to the system. This is obviously not correct, so
fix it to avoid confusing the users.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2007-01-04 11:43:35 +01:00
Soeren Sonnenburg
10f549fa15 [PATCH] make fn_keys work again on power/macbooks
The apple fn keys don't work anymore with 2.6.20-rc1.

The reason is that USB_HID_POWERBOOK appears in several files although
USB_HIDINPUT_POWERBOOK is the thing to be used.

The patch fixes this.

Cc: Greg KH <greg@kroah.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-30 10:55:55 -08:00
Linus Torvalds
18ed1c0513 Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (68 commits)
  ACPI: replace kmalloc+memset with kzalloc
  ACPI: Add support for acpi_load_table/acpi_unload_table_id
  fbdev: update after backlight argument change
  ACPI: video: Add dev argument for backlight_device_register
  ACPI: Implement acpi_video_get_next_level()
  ACPI: Kconfig - depend on PM rather than selecting it
  ACPI: fix NULL check in drivers/acpi/osl.c
  ACPI: make drivers/acpi/ec.c:ec_ecdt static
  ACPI: prevent processor module from loading on failures
  ACPI: fix single linked list manipulation
  ACPI: ibm_acpi: allow clean removal
  ACPI: fix git automerge failure
  ACPI: ibm_acpi: respond to workqueue update
  ACPI: dock: add uevent to indicate change in device status
  ACPI: ec: Lindent once again
  ACPI: ec: Change #define to enums there possible.
  ACPI: ec: Style changes.
  ACPI: ec: Acquire Global Lock under EC mutex.
  ACPI: ec: Drop udelay() from poll mode. Loop by reading status field instead.
  ACPI: ec: Rename gpe_bit to gpe
  ...
2006-12-22 18:46:56 -08:00
Greg Kroah-Hartman
c305290503 USB Storage: remove duplicate Nokia entry in unusual_devs.h
How many times are we going to merge this entry...

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 11:46:03 -08:00
Eric Smith
11e82730cc [PATCH] usb serial: add support for Novatel S720/U720 CDMA/EV-DO modems
Add USB vendor/device IDs for Novatel Wireless S720 and U720 CDMA/EV-DO
modems to airprime.c.

Signed-off-by: Eric Smith <eric@brouhaha.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 11:29:18 -08:00
Andrew Morton
a5176b7897 [PATCH] USB: Nokia E70 is an unusual device
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=7508

When the Nokia E70 Phone is plugged in to the USB port, I get:

end_request: I/O error, dev sda, sector 1824527
sd 0:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 1824535
sd 0:0:0:0: SCSI error: return code = 0x10070000

The fix is to add these lines to drivers/usb/storage/unusual_devs.h:

Cc: <honkkis@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 11:29:04 -08:00
Chris Frey
df251b8bfc USB: fix to usbfs_snoop logging of user defined control urbs
When sending CONTROL URB's using the usual CONTROL ioctl, logging works
fine, but when sending them via SUBMITURB, like VMWare does, the
control fields are not logged.  This patch fixes that.

I didn't see any major changes to devio.c recently, so this patch should apply
cleanly to even the latest kernel.  I can resubmit if it doesn't.

From: Chris Frey <cdfrey@foursquare.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:28 -08:00
Wojtek Kaniewski
bfb7fb79e9 USB: at91_udc: Additional checks
This patch performs additional checks in at91_udc, just in case of
some spurious interrupts or device enumeration.

Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:27 -08:00
Wojtek Kaniewski
943c441948 USB: at91_udc: Cleanup variables after failure in usb_gadget_register_driver()
This patch zeroes some variables when usb_gadget_register_driver()
fails. gadgetfs does a dummy registration to get the name of the USB
driver and then waits for user-land driver. If someone plugs the cable
in the meantime, bad things happen, because at91_udc has been left in
inconsistent state.

Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:27 -08:00
Wojtek Kaniewski
bc92c32aa2 USB: at91_udc: allow drivers that support high speed
This patch allows gadget drivers that support high speed (e.g. gadgetfs)
to work properly with at91_udc.

Fix suggested by Milan Svoboda in
http://marc.theaimsgroup.com/?l=linux-usb-devel&m=115822184711817

Signed-off-by: Wojtek Kaniewski <wojtekka@toxygen.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:27 -08:00
Tony Olech
4b87361d49 USB: u132-hcd/ftdi-elan: add support for Option GT 3G Quad card
ELAN's U132 is a USB to CardBus OHCI controller adapter,
    designed specifically for CardBus 3G data cards to
    function in machines without a CardBus slot.
The "ftdi-elan" module is a USB client driver, that detects
    a supported CardBus OHCI controller plugged into the
    U132 adapter and thereafter provides the conduit for
    for access by the "u132-hcd" module.
The "u132-hcd" module is a (cut-down OHCI) host controller
    that supports a single OHCI function of the CardBus 
    card inserted into the U132 adapter.

The problem with the initial implementation is that when
the CardBus card inserted into the U132 adapter has multiple
functions (and a CardBus card can support up to 4 functions),
it was the first function that was arbitrarily choosen.

The first batch of 3G cards tested, like the Merlin Qualcomm
V620, have two functions each supporting a seperate USB OHCI
host controller, of which it was that first function that is
wired up to the 3G modem.

Then along comes the Vodafone Mobile Connect 3G/GPRS data card,
aka "Option GT 3G Quad" as printed on it's rear or "Option N.V.
GlobeTrotter Fusion Quad Lite" as read with "lspci -v". And it
has the meaningful functionality in the second CardBus function.

That presents a problem because it was the "ftdi-elan" module
alone that knows how to communicate to the embedded CardBus slot
and the "u132-hcd" module alone that knows how to access the
pcmcia configuration and CardBus accessible memory space. And
of course, the information about attached (internally hardwired)
devices is contained within USB configuration embedded somewhere
within the CardBus card.

If only the "u132-hcd" module probe() interface could return a
result code that propagated back to the instigating function
platform_device_register() then the "ftdi-elan" module could
try an alternative CardBus function.     However in spite of
the recent changes to the drivers/base/ routines that moved 
device_attach() from bus_add_device() to bus_attach_device()
both of those routines lose the "failed to attach" 0 result
code and thus the calling routine, namely device_add() is
incapable of propaging the "failed to attach" condition back
to platform_device_add() and consequently back to the caller
of platform_device_register()

Experiments show that patching bus_attach_device() to return
ENODEV fails with the kernel locking up very early during
boot. But, however, if the patch is restricted to calls from
platform_device_add() then it does seem to work.

Unfortunately, until the kernel's drivers/base is properly
modified to propagate -ENODEV back to the caller of
platform_device_register(), it is necessary to "fix" the
"ftdi-elan" module by importing knowledge from the 
"u132-hcd" module. This is the reason for the duplicated
functionality introduced in this patch.

Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:27 -08:00
Andrew Victor
29ba4b533b USB: at91_udc, misc fixes
This is an update to the AT91 USB Device (Gadget) driver.

Adds support for the Atmel AT91SAM9260 and AT91SAM9261 processors.  The
only difference is how they handle the pullup pin.
[Patch from Patrice Vilchez]

Need to clear any pending USB Device interrupts before registering the
interrupt handler.  The bootloader might have been using the USB Device
port.   [Patch from Peer Georgi]

VBUS detection is handled by a GPIO interrupt which only triggers on a
change. Is is therefore necessary to read the current VBUS state
explicitly at startup.  [Patch from Peer Georgi]


Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:27 -08:00
Andrew Victor
ffd3326bf6 USB: at91 udc, support at91sam926x addresses
This is an update to the AT91 USB Device (Gadget) driver.

The base I/O address provided in the platform_device resources is now
ioremap()'ed instead of using a statically mapped memory area.  This
helps portability to the newer AT91sam926x processors.

The major change is that we now have to pass a 'struct at91_udc'
parameter to at91_udp_read() and at91_udp_write().

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:27 -08:00
Vitaly Wool
5151d04068 USB: OHCI support for PNX8550
OHCI HCD (Host Controller Driver) for USB. Bus Glue for PNX8550.

Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:27 -08:00
Takamasa Ohtake
23d10a9e37 USB: ohci handles hardware faults during root port resets
I have found a problem where the root_port_reset() goes into an infinite
loop and stalls the kernel.

This happens when a hardware fault inside the machine occurs during a small
timing window.  In case of USB device connection, if a USB device responds to
hcd_submit_urb(), and later the controller fails before root_port_reset(),
root_port_reset() will loop infinitely because ohci_readl() will always
return "-1".  Such a failure can include ejecting a CardBus OHCI controller.

The probability of this problem is low, but it will increase if PnP type
usage is frequent.  The attached patch can solve this problem and I believe
that it is better to fix this problem.

Signed-off-by: Takamasa Ohtake <ohtake-txa@necst.nec.co.jp>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:27 -08:00
Andrew Victor
ee269d98a9 USB: ohci at91 warning fix
Remove a warning about an unused variable in the OHCI bus glue for at91.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:27 -08:00
David Brownell
dd9048af41 USB: ohci whitespace/comment fixups
This is an OHCI cleanup patch ... it removes a lot of erroneous whitespace
(space before tab, at end of line) as well as the obsolete inline changelog.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:26 -08:00
David Brownell
6bea476cf6 USB: gadget driver unbind() is optional; section fixes; misc
Allow gadget drivers to omit the unbind() method.  When they're
statically linked, that's an appropriate memory saving tweak.

Similarly, provide consistent/simpler handling for a should-not-happen
error case:  removing a peripheral controller driver when a gadget
driver is still loaded.  Such code dates back to early versions of the
first implementation of the gadget API, and has never been triggered.

Includes relevant section annotation fixs for gmidi.c, file_storage.c,
and serial.c; we don't yet have an "init or exit" annotation.  Also
some whitespace fixes in gmidi.c (space at EOL, before tabs, etc).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:26 -08:00
Alan Stern
5f8364b7d6 UHCI: module parameter to ignore overcurrent changes
Certain boards seem to like to issue false overcurrent notifications,
for example on ports that don't have anything connected to them.  This
looks like a hardware error, at the level of noise to those ports'
overcurrent input signals (or non-debounced VBUS comparators).  This
surfaces to users as truly massive amounts of syslog spam from khubd
(which is appropriate for real hardware problems, except for the
volume from multiple ports).

Using this new "ignore_oc" flag helps such systems work more sanely,
by preventing such indications from getting to khubd (and spamming
syslog).  The downside is of course that true overcurrent errors will
be masked; they'll appear as spontaneous disconnects, without the
diagnostics that will let users troubleshoot issues like
short-circuited cables.  In addition, controllers with no devices
attached will be forced to poll for new devices rather than relying on
interrupts, since each overcurrent event would generate a new
interrupt.

This patch (as826) is essentially a copy of David Brownell's ignore_oc
patch for ehci-hcd, ported to uhci-hcd.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:26 -08:00
Andrew Morton
fe1ec341df USB: Nokia E70 is an unusual device
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=7508

When the Nokia E70 Phone is plugged in to the USB port, I get:

end_request: I/O error, dev sda, sector 1824527
sd 0:0:0:0: SCSI error: return code = 0x10070000
end_request: I/O error, dev sda, sector 1824535
sd 0:0:0:0: SCSI error: return code = 0x10070000

The fix is to add these lines to drivers/usb/storage/unusual_devs.h:

Cc: <honkkis@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:26 -08:00
Burman Yan
66eb2e93b9 USB AUERSWALD: replace kmalloc+memset with kzalloc
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:26 -08:00
Ping Cheng
071e0a2aee USB: fix Wacom Intuos3 4x6 bugs
Fixes Intuos3 4x6 bugs

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:26 -08:00
Johann Wilhelm
ab19589055 usb-gsm-driver: Added VendorId and ProductId for Huawei E220 USB Modem
Added VendorId and ProductId for Huawei E220 USB Modem

Signed-off-by: Johann Wilhelm <johann.wilhelm@student.tugraz.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:25 -08:00
Johann Wilhelm
16c76865df usb-storage: Ignore the virtual cd-drive of the Huawei E220 USB Modem
This prevents the kernel from detecting the virtual cd-drive with the
Windows drivers.

Signed-off-by: Johann Wilhelm <johann.wilhelm@student.tugraz.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:25 -08:00
Petko Manolov
5859271ebd USB: rtl8150 new device id
This one adds another vendor ID to rtl8150 driver.  Please apply.


Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:25 -08:00
Jeff Garzik
abc9404bb0 USB: fix ohci.h over-use warnings
When u132-hcd is built, it includes local header ohci.h, which appears
to have been intended only for use by ohci-hcd.

This throws warnings about functions which are defined and not used.
The warnings thrown are because three small functions are implemented in
the header, but not declared 'inline', a rather strange affair.

Since these functions are small, let's go ahead and define them as
'inline', just like the inline functions surrounding them.  This makes
things more consistent, and kills the warnings.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:25 -08:00
David Clare
c2585d9625 USB: Prevent the funsoft serial device from entering raw mode
Added a device specific ioctl function to prevent the disabling of canonical
mode.  EINVAL is returned for any TCSETSF ioctl that doesn't have ICANON set.
This patch is for 2.6.17 or later kernels.

When "hwinfo --modem" is executed it opens the funsoft USB serial device and
disables canonical mode.  The device is kept this way until hwininfo has
finished probing any modems on a system.  The funsoft device expects to be
running in canonical mode.  Switching the device to raw mode can cause
incomplete data packets and device timeouts.

Signed-off-by: David Clare <david@funsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:25 -08:00
Johannes Hoelzl
e05998d50d Add Baltech Reader ID to CP2101 driver
this patch adds the Baltech Reader ID to the list of USB IDs in the
CP2101 driver.

From: Johannes Hoelzl <johannes.hoelzl@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:25 -08:00
Oliver Neukum
8e42266965 USB: mutexification of usblp
this patch:
- converts usblp fully to mutex
- makes sleeping interruptible where EINTR can be returned anyway

Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:13:23 -08:00
Alan
b1cff285ae usb serial: Eliminate bogus ioctl code
Several drivers have bogus ioctl code that tries unneccessarily to
override the standard processing. In the three cases here the actual code
is not only wrong but also not required as they implement the proper
set_termios method as well.

Remove the junk.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:13:23 -08:00
Oliver Neukum
337445313f USB: removing ifdefed code from gl620a
as David has objected to the patch against the gl620a driver,
here's a patch implementing David' suggestion of removing the incomplete
ifdefed code from the gl620a driver.


Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
2006-12-20 10:13:23 -08:00
Jan Capek
ec434e9b43 USB: ftdi_sio - MachX product ID added
below is a patch for the ftdi_sio driver to include a new device ID for
CCS MachX PIC programmer.


From: Jan Capek <jan@ccsinfo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:13:23 -08:00
Eagle Jones
87f28bde94 USB: airprime: add device id for dell wireless 5500 hsdpa card
Added the device id (0x413c, 0x8115) for the Dell wireless HSDPA 5500,
which is a rebranded Novatel EU730.

Signed-off-by: Eagle Jones <eagle@newdream.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:13:23 -08:00
Oliver Neukum
96ca014d53 USB: fix transvibrator disconnect race
in disconnect you set the interface's private data to NULL. In your IO
methods you unconditionally follow the pointer into never never land.

Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:13:23 -08:00
Sean Young
6a7255e1df USB: Fix oops in PhidgetServo
The PhidgetServo causes an Oops when any of its sysfs attributes are read
or written too, making the driver useless.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:13:22 -08:00
Len Brown
9774f33841 merge linus into test branch 2006-12-20 02:53:13 -05:00
Len Brown
40b20c257a Pull platform-drivers into test branch 2006-12-20 02:52:17 -05:00
Yu Luming
519ab5f2be ACPI: video: Add dev argument for backlight_device_register
This patch set adds generic abstract layer support for acpi video driver to
have generic user interface to control backlight and output switch control by
leveraging the existing backlight sysfs class driver, and by adding a new
video output sysfs class driver.

This patch:

Add dev argument for backlight_device_register to link the class device to
real device object.  The platform specific driver should find a way to get the
real device object for their video device.

[akpm@osdl.org: build fix]
[akpm@osdl.org: fix msi-laptop.c]
Signed-off-by: Luming Yu <Luming.yu@intel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-12-20 01:42:19 -05:00
Jiri Kosina
e3a0dd7ced [PATCH] Generic HID layer - build: USB_HID should select HID
Let CONFIG_USB_HID imply CONFIG_HID. Making it only dependent might confuse
users to choose CONFIG_HID, but no particular HID transport drivers.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2006-12-14 13:37:23 +01:00
Robert P. J. Day
5cbded585d [PATCH] getting rid of all casts of k[cmz]alloc() calls
Run this:

	#!/bin/sh
	for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
	  echo "De-casting $f..."
	  perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
	done

And then go through and reinstate those cases where code is casting pointers
to non-pointers.

And then drop a few hunks which conflicted with outstanding work.

Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13 09:05:58 -08:00
Robert P. J. Day
cd86128088 [PATCH] Fix numerous kcalloc() calls, convert to kzalloc()
All kcalloc() calls of the form "kcalloc(1,...)" are converted to the
equivalent kzalloc() calls, and a few kcalloc() calls with the incorrect
ordering of the first two arguments are fixed.

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13 09:05:52 -08:00
Jiri Kosina
63f3861d2f [PATCH] Generic HID layer - build
This modifies Makefiles and Kconfigs to properly reflect the creation of
generic HID layer.

It also removes the dependency of BROKEN, which was introduced by the
first patch in series (see the comment). Also updates credits.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-08 10:43:20 -08:00
Jiri Kosina
4c2ae844b5 [PATCH] Generic HID layer - pb_fnmode
pb_fnmode parameter has to be passed to usbhid, both for compatibility reasons
and also because it logically belongs there.

Also removes empty hid-input.c file in drivers/usb/input.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-08 10:43:19 -08:00
Jiri Kosina
aa8de2f038 [PATCH] Generic HID layer - input and event reporting
hid_input_report() was needlessly USB-specific in USB HID. This patch
makes the function independent of HID implementation and fixes all
the current users. Bluetooth patches comply with this prototype.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-08 10:43:17 -08:00
Jiri Kosina
aa938f7974 [PATCH] Generic HID layer - hiddev
- hiddev is USB-only (agreed with Marcel Holtmann that Bluetooth currently
  doesn't need it, and future planned interface (rawhid) will be more flexible
  and usable)
- both HID and USB-hid can be now compiled as modules (wasn't possible before
  hiddev was fully separated from generic HID layer)

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-08 10:43:15 -08:00
Jiri Kosina
4916b3a57f [PATCH] Generic HID layer - USB API
- 'dev' in struct hid_device changed from struct usb_device to
  struct device and fixed all the users
- renamed functions which are part of USB HID API from 'hid_*' to
  'usbhid_*'
- force feedback initialization moved from common part into USB-specific
  driver
- added usbhid.h header for USB HID API users
- removed USB-specific fields from struct hid_device and moved them
  to new usbhid_device, which is pointed to by hid_device->driver_data
- fixed all USB users to use this new structure

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-08 10:43:14 -08:00
Jiri Kosina
229695e51e [PATCH] Generic HID layer - API
- fixed generic API (added neccessary EXPORT_SYMBOL, fixed hid.h to provide correct
  prototypes)
- extended hid_device with open/close/event function pointers to driver-specific
  functions
- added driver specific driver_data to hid_device

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-08 10:43:12 -08:00
Jiri Kosina
dde5845a52 [PATCH] Generic HID layer - code split
The "big main" split of USB HID code into generic HID code and
USB-transport specific HID handling.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-08 10:43:01 -08:00
Jiri Kosina
64bb67b170 [PATCH] Generic HID layer - disable USB HID
This patch is a part of generic HID layer introduction. USB HID is
disabled, so that the code split and changes could be introduced in a
way that is reviewable (i.e. separate patches), but not to break git
bisect by uncompilable kernel throughout different stages of the code
splitup and changes. The last patch of this series enables HID again.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-08 10:19:04 -08:00
Alan Cox
606d099cdd [PATCH] tty: switch to ktermios
This is the grungy swap all the occurrences in the right places patch that
goes with the updates.  At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs

If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.

If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)

Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia

[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:57 -08:00
Josef Sipek
33cb899400 [PATCH] struct path: convert usb
Signed-off-by: Josef Sipek <jsipek@fsl.cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:50 -08:00
Dmitry Torokhov
bef986502f Merge rsync://rsync.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/usb/input/hid.h
2006-12-08 01:07:56 -05:00
Linus Torvalds
ea14fad0d4 Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
  [ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
  [ARM] 4001/1: S3C24XX: shorten reboot time
  [ARM] 3983/2: remove unused argument to __bug()
  [ARM] 4000/1: Osiris: add third serial port in
  [ARM] 3999/1: RX3715: suspend to RAM support
  [ARM] 3998/1: VR1000: LED platform devices
  [ARM] 3995/1: iop13xx: add iop13xx support
  [ARM] 3968/1: iop13xx: add iop13xx_defconfig
  [ARM] Update mach-types
  [ARM] Allow gcc to optimise arm_add_memory a little more
  [ARM] 3991/1: i.MX/MX1 high resolution time source
  [ARM] 3990/1: i.MX/MX1 more precise PLL decode
  [ARM] 3986/1: H1940: suspend to RAM support
  [ARM] 3985/1: ixp4xx clocksource cleanup
  [ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
  [ARM] 3994/1: ixp23xx: fix handling of pci master aborts
  [ARM] 3981/1: sched_clock for PXA2xx
  [ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
  [ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
  [ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
  ...
2006-12-07 15:40:39 -08:00
Nigel Cunningham
7dfb71030f [PATCH] Add include/linux/freezer.h and move definitions from sched.h
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.

[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:27 -08:00
Christoph Lameter
e18b890bb0 [PATCH] slab: remove kmem_cache_t
Replace all uses of kmem_cache_t with struct kmem_cache.

The patch was generated using the following script:

	#!/bin/sh
	#
	# Replace one string by another in all the kernel sources.
	#

	set -e

	for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
		quilt add $file
		sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
		mv /tmp/$$ $file
		quilt refresh
	done

The script was run like this

	sh replace kmem_cache_t "struct kmem_cache"

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:25 -08:00
Christoph Lameter
441e143e95 [PATCH] slab: remove SLAB_DMA
SLAB_DMA is an alias of GFP_DMA. This is the last one so we
remove the leftover comment too.

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:24 -08:00
Christoph Lameter
e94b176609 [PATCH] slab: remove SLAB_KERNEL
SLAB_KERNEL is an alias of GFP_KERNEL.

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:24 -08:00
Christoph Lameter
54e6ecb239 [PATCH] slab: remove SLAB_ATOMIC
SLAB_ATOMIC is an alias of GFP_ATOMIC

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:24 -08:00
Christoph Lameter
55acbda096 [PATCH] slab: remove SLAB_NOIO
SLAB_NOIO is an alias of GFP_NOIO with a single instance of use.

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:23 -08:00
David Howells
4796b71fbb Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/pcmcia/ds.c

Fix up merge failures with Linus's head and fix new compile failures.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-06 15:01:18 +00:00
David Howells
6d5aefb8ea WorkQueue: Fix up arch-specific work items where possible
Fix up arch-specific work items where possible to use the new work_struct and
delayed_work structs.

Three places that enqueue bits of their stack and then return have been marked
with #error as this is not permitted.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-05 19:36:26 +00:00
David Howells
4c1ac1b491 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/infiniband/core/iwcm.c
	drivers/net/chelsio/cxgb2.c
	drivers/net/wireless/bcm43xx/bcm43xx_main.c
	drivers/net/wireless/prism54/islpci_eth.c
	drivers/usb/core/hub.h
	drivers/usb/input/hid-core.c
	net/core/netpoll.c

Fix up merge failures with Linus's head and fix new compilation failures.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-05 14:37:56 +00:00
Dominik Brodowski
af2b3b503a [PATCH] pcmcia: conf.ConfigBase and conf.Present consolidation
struct pcmcia_device *p_dev->conf.ConfigBase and .Present are set in almost
all PCMICA driver right at the beginning, using the same calls but slightly
different implementations. Unfiy this in the PCMCIA core.

Includes a small bugfix ("drivers/net/pcmcia/xirc2ps_cs.c: remove unused
label") from and Signed-off-by Adrian Bunk <bunk@stusta.de>

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2006-12-04 20:12:02 -05:00
Linus Torvalds
9641219825 Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (103 commits)
  usbcore: remove unused argument in autosuspend
  USB: keep count of unsuspended children
  USB hub: simplify remote-wakeup handling
  USB: struct usb_device: change flag to bitflag
  OHCI: make autostop conditional on CONFIG_PM
  USB: Add autosuspend support to the hub driver
  EHCI: Fix root-hub and port suspend/resume problems
  USB: create a new thread for every USB device found during the probe sequence
  USB: add driver for the USB debug devices
  USB: added dynamic major number for USB endpoints
  USB: pegasus error path not resetting task's state
  USB: endianness fix for asix.c
  USB: build the appledisplay driver
  USB serial: replace kmalloc+memset with kzalloc
  USB: hid-core: canonical defines for Apple USB device IDs
  USB: idmouse cleanup
  USB: make drivers/usb/core/driver.c:usb_device_match() static
  USB: lh7a40x_udc remove double declaration
  USB: pxa2xx_udc recognizes ixp425 rev b0 chip
  usbtouchscreen: add support for DMC TSC-10/25 devices
  ...
2006-12-01 16:41:58 -08:00
Alan Stern
94fcda1f8a usbcore: remove unused argument in autosuspend
Thanks to several earlier patches, usb_autosuspend_device() and
usb_autoresume_device() are never called with a second argument other
than 1.  This patch (as819) removes the now-redundant argument.

It also consolidates some common code between those two routines,
putting it into a new subroutine called usb_autopm_do_device().  And
it includes a sizable kerneldoc update for the affected functions.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:53 -08:00
Alan Stern
ee49fb5dc8 USB: keep count of unsuspended children
This patch (as818b) simplifies autosuspend processing by keeping track
of the number of unsuspended children of each USB hub.  This will
permit us to avoid a good deal of unnecessary work all the time; we
will no longer have to create a bunch of workqueue entries to carry
out autosuspend requests, only to have them fail because one of the
hub's children isn't suspended.

The basic idea is simple.  There already is a usage counter in the
usb_device structure for preventing autosuspends.  The patch just
increments that counter for every unsuspended child.  There's only one
tricky part: When a device disconnects we need to remember whether it
was suspended at the time (leave the counter alone) or not (decrement
the counter).

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Alan Stern
d25450c687 USB hub: simplify remote-wakeup handling
This patch (as817) simplifies the remote-wakeup processing in the hub
driver.  Now instead of using a specialized code path, it relies on
the standard USB resume routines.  The hub_port_resume() function does
an initial get_port_status() to see whether the port has already
resumed itself (as it does when a remote-wakeup request is sent).
This will slow down handling of other resume events slightly, but not
enough to matter.

The patch also changes the hub_port_status() routine, making it return
an error if a short reply is received.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Alan Stern
ce3615879a USB: struct usb_device: change flag to bitflag
This patch (as816) changes an existing flag in the usb_device
structure to a bitflag, preparing the way for more bitflags to come
in the future.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Alan Stern
1f9fc882d9 OHCI: make autostop conditional on CONFIG_PM
Unlike UHCI, OHCI does not exert any DMA load on the system when no
devices are connected.  Consequently there is no advantage to doing
an autostop other than the power savings, so we shouldn't compile the
necessary code unless CONFIG_PM is enabled.

This patch (as820) makes the root-hub suspend and resume routines
conditional on CONFIG_PM.  It also prevents autostop from activating
if the device_may_wakeup flag isn't set; some people use this flag to
alert the driver about Resume-Detect bugs in the hardware.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Alan Stern
40f122f343 USB: Add autosuspend support to the hub driver
This patch (as742b) adds autosuspend/autoresume support to the USB hub
driver.  The largest aspect of the change is that we no longer need a
special flag for root hubs that want to be resumed.  Now every hub is
autoresumed whenever khubd needs to access it.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Alan Stern
8c03356a55 EHCI: Fix root-hub and port suspend/resume problems
This patch (as738b) fixes numerous problems in the controller/root-hub
suspend/resume/remote-wakeup support in ehci-hcd:

	The bus_resume() routine should wake up only the ports that
	were suspended by bus_suspend().  Ports that were already
	suspended should remain that way.

	The interrupt mask is used to detect loss of power in the
	bus_resume() routine (if the mask is 0 then power was lost).
	However bus_suspend() always sets the mask to 0.  Instead the
	mask should retain its normal value, with port-change-detect
	interrupts disabled if remote wakeup is turned off.

	The interrupt mask should be reset to its correct value at the
	end of bus_resume() regardless of whether power was lost.

	bus_resume() reinitializes the operational registers if power
	was lost.  However those registers are not in the aux power
	well, hence they can lose their values whenever the controller
	is put into D3.  They should always be reinitialized.

	When a port-change interrupt occurs and the root hub is
	suspended, the interrupt handler should request a root-hub
	resume instead of starting up the controller all by itself.

	There's no need for the interrupt handler to request a
	root-hub resume every time a suspended port sends a
	remote-wakeup request.

	The pci_resume() method doesn't need to check for connected
	ports when deciding whether or not to reset the controller.
	It can make that decision based on whether Vaux power was
	maintained.

	Even when the controller does not need to be reset,
	pci_resume() must undo the effect of pci_suspend() by
	re-enabling the interrupt mask.

	If power was lost, pci_resume() must not call ehci_run().
	At this point the root hub is still supposed to be suspended,
	not running.  It's enough to rewrite the command register and
	set the configured_flag.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Greg Kroah-Hartman
c066475e1f USB: create a new thread for every USB device found during the probe sequence
Might speed up some systems.  If nothing else, a bad driver should not
take the whole USB subsystem down with it.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Greg Kroah-Hartman
958e8741bf USB: add driver for the USB debug devices
It's a simple usb-serial driver that just creates a tty device to read
and write from.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Sarah Bailey
7e27780ffd USB: added dynamic major number for USB endpoints
This patch is an update for Greg K-H's proposed usbfs2:
http://sourceforge.net/mailarchive/message.php?msg_id=19295229

It creates a dynamic major for USB endpoints and fixes
the endpoint minor calculation.

Signed-off-by: Sarah Bailey <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Oliver Neukum
10c8211c63 USB: pegasus error path not resetting task's state
there is an error path in the pegasus driver which can leave
the task in TASK_UNINTERRUPTIBLE. Depending on when it
schedules next, this can be bad.

Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:51 -08:00
Oliver Neukum
9aa742ef7c USB: endianness fix for asix.c
the latest update for asix.c reverted some endianness fixes. This
reinstates them.

Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:51 -08:00
Adrian Bunk
8feabf70f5 USB: build the appledisplay driver
We do already have both the code and a config option, so why not build
this driver?  ;-)

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:51 -08:00
Burman Yan
7ac9da10af USB serial: replace kmalloc+memset with kzalloc
Replace kmalloc+memset with kzalloc

Signed-off-by: Yan Burman <yan_952@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:51 -08:00
Julien BLACHE
afd21ee5ab USB: hid-core: canonical defines for Apple USB device IDs
Use canonical defines for the Apple USB device IDs.
Also add the Geyser IV devices missing in my previous patch.

Signed-off-by: Julien BLACHE <jb@jblache.org>
Acked-by: Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:38 -08:00
Mariusz Kozlowski
54ecf1fba6 USB: idmouse cleanup
Just digging through code and found these needless variable initializations. So here is the patch.

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
Adrian Bunk
8bb22d2bda USB: make drivers/usb/core/driver.c:usb_device_match() static
usb_device_match() can now become static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
David Brownell
7481bb8a7f USB: lh7a40x_udc remove double declaration
Remove minor double-declaration goof.

Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
David Brownell
827982c577 USB: pxa2xx_udc recognizes ixp425 rev b0 chip
Make the pxa2xx_udc driver recognize a newer revision of the IXP425 chip.

Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
Holger Schurig
24ced062a2 usbtouchscreen: add support for DMC TSC-10/25 devices
Adds support for the DMC TSC-10 and TSC-25 usb touchscreen controllers.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
Adrian Bunk
9ce8540c88 USB: ftdi-elan.c: fixes and cleanups
This patch contains the following possible cleanups:
- make the needlessly global ftdi_release_platform_dev() static
- remove the unused usb_ftdi_elan_read_reg()
- proper prototypes for the following functions:
  - usb_ftdi_elan_read_pcimem()
  - usb_ftdi_elan_write_pcimem()

Note that the misplaced prototypes for the latter ones in
drivers/usb/host/u132-hcd.c were buggy. Depending on the calling
convention of the architecture calling one of them could have turned
your stack into garbage.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
Adrian Bunk
27a3de4cfc USB: make drivers/usb/host/u132-hcd.c:u132_hcd_wait static
This patch makes the needlessly global "u132_hcd_wait" static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
Mariusz Kozlowski
2e46b74852 usb: cypress_m8 init error path fix
If at some point cypress_init() fails deregister
only the resources that were registered until that point.

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
David Brownell
93f1a47c4a USB: add ehci_hcd.ignore_oc parameter
Certain boards seem to like to issue false overcurrent notifications, for
example on ports that don't have anything connected to them.  This looks
like a hardware error, at the level of noise to those ports' overcurrent
input signals (or non-debounced VBUS comparators).  This surfaces to users
as truly massive amounts of syslog spam from khubd (which is appropriate
for real hardware problems, except for the volume from multiple ports).

Using this new "ignore_oc" flag helps such systems work more sanely, by
preventing such indications from getting to khubd (and spam syslog).  The
downside is of course that true overcurrent errors will be masked; they'll
appear as spontaneous disconnects, without the diagnostics that will let
users troubleshoot issues like short circuited cables.

Note that the bulk of these reports seem to be with VIA southbridges, but
I think some were with Intel ones.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
David Brownell
f0d7f27351 USB: EHCI hooks for high speed electrical tests
EHCI hooks for high speed electrical tests of the root hub ports.

The expectation is that a usermode program actually triggers the test,
making the same control request it would make for an external hub.
Tests for peripheral upstream ports would issue a different request.
In all cases, the hardware needs re-initialization before it could
be used "normally" again (e.g. unplug/replug, rmmod/modprobe).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:36 -08:00
Alan Stern
1f26e28d3e USB: net2280: don't send unwanted zero-length packets
The net2280 driver is too eager to send zero-length packets when
IN tokens are received on ep0.  No such packet should be sent (the
driver should NAK) before the gadget driver has queued the proper
response.  Otherwise deferred responses are impossible.

This patch (as823) makes net2280 avoid sending ZLPs for IN transfers
on ep0 until a response has been submitted, and avoids stalling when an
OUT packet is received before a request has been submitted for an OUT
transfer on ep0.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:36 -08:00
Mariusz Kozlowski
a3b1f50ce2 usb: microtek possible memleak fix
Possible memleak fix on error path. The changes:

- out_kfree2 and out_free_urb replaced
- missing scsi_host_put() added

Here it goes:

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:36 -08:00
Jaco Kroon
49314378ac USB: add Digitech USB-Storage to unusual_devs.h
The mass storage device from Digitech designed for Flash Cards, as found
on (for example) the GNX4 device has issues with residue, similar to the
bug report at http://kerneltrap.org/node/6297.  This patch adds the
faulty storage device to unusual_devs.h, this not only reduces the noise
in dmesg but also increases the transfer speeds by a factor of 7x for me
(89kB/s -> 637kB/s).

T:  Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1210 ProdID=0003 Rev= 1.00
S:  Manufacturer=DigiTech HMG
S:  Product=DigiTech Mass Storage
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms

Signed-off-by: Jaco Kroon <jaco@kroon.co.za>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:35 -08:00
Alan Stern
db063507b4 USB core: fix compiler warning about usb_autosuspend_work
This patch (as821) fixes a compiler warning when CONFIG_PM isn't on
("usb_autosuspend_work" defined but not used).

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:35 -08:00
Naranjo Manuel Francisco
7a5c7b42d3 USB: fix aircable.c: inconsequent NULL checking
> 2006/11/11, Adrian Bunk <bunk@stusta.de>:
> > The Coverity checker spotted the following in
> > drivers/usb/serial/aircable.c:
> >
> > <--  snip  -->
> >
> > ...
> > static void aircable_read(void *params)
> > {
> > ...


Hi everyone,
Sorry for the long time response but here is the patch, I think this way should
work, if anyone has any suggestion let me know. What I do now is, in case I
don't have the tty available I reschedule the work, I have tried it and it
works with no problem, I even tried removing the device, and didn't find
anything strange.

Signed-off-by: Naranjo Manuel <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:35 -08:00
Alan Stern
1b7be3c066 OHCI: change priority level of resume log message
All the other root-hub suspend or resume log messages, in ohci-hcd or
any of the other host controller drivers, use the debug priority
level.  This patch (as815) makes the one single exception behave like
all the rest.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:35 -08:00
Mariusz Kozlowski
bcb54a5403 usb: visor kill urb cleanup
- usb_kill_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:35 -08:00
Mariusz Kozlowski
95d4316654 usb: usb-serial free urb cleanup
- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:35 -08:00
Mariusz Kozlowski
9aac10ff1d usb: navman kill urb cleanup
- usb_kill_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:35 -08:00
Mariusz Kozlowski
73135bb915 usb: mct_u232 free urb cleanup
- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
5505c2261e usb: kobil_sct kill urb cleanup
- usb_kill_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
1cadc1378f usb: keyspan free urb cleanup
- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
9a25f44f91 usb: io_edgeport kill urb cleanup
- usb_kill_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
c69694b779 usb: catc free urb cleanup
- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
794c944ecd usb: ftdi_sio kill urb cleanup
- usb_kill_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
5483eb1300 usb: phidgetmotorcontrol free urb cleanup
- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
df43121463 usb: phidgetkit free urb cleanup
- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
f53510e8c4 usb: legousbtower free kill urb cleanup
Hello,

- usb_free_urb() cleanup
- usb_kill_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
2891a51cc2 usb: auerswald free kill urb cleanup
- usb_free_urb() cleanup
- usb_kill_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:34 -08:00
Mariusz Kozlowski
4ba0b2ed58 usb: usbkbd free urb cleanup
- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:33 -08:00
Mariusz Kozlowski
6f07429fa2 usb: hid-core free urb cleanup
- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:33 -08:00
Mariusz Kozlowski
2381526a79 usb: ati_remote2 free urb cleanup
Hello,

- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:33 -08:00
Mariusz Kozlowski
459f836a61 usb: ati_remote free urb cleanup
- usb_free_urb() cleanup

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:33 -08:00
Oleg Verych
1f54a6ae79 usb-serial: ti_usb, TI ez430 development tool ID
usb-serial: ti_usb, TI ez430 development tool ID

Signed-off-by: Oleg Verych <olecom@flower.upol.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00
daniel@centurion.net.nz
ad0327d680 USB: airprime: New device ID
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00
Adrian Bunk
54c9b2266f USB: make drivers/usb/input/wacom_sys.c:wacom_sys_irq() static
This patch makes the needlessly global wacom_sys_irq() static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00
Stephen Hemminger
d5ec1686ba USB: resume_device symbol conflict
Several functions in USB core overlap with global functions.
The linker appears to do the right thing, but it is bad practice and makes
debugging harder.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00
David Brownell
d8126a0c23 usb/gadget/ether.c minor manycast tweaks
Minor cleanup/clarification in the ethernet gadget driver, using standard
calls to test for Ethernet multicast and broadcast addresses.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00
Alan Stern
1bb5f66bb3 USB: Move private hub declarations out of public header file
This patch (as809b) moves the declaration of the hub driver's private
data structure from hub.h into the hub.c source file.  Lots of other
files import hub.h; they have no need to know about the details of the
hub driver's private data.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00
Jean Delvare
b4ee4a2309 USB: net1080: Fix && typos
Fix STATUS_PACKETS_* macros, where "&&" was mistakenly used where
"&" should have.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00
Alan Stern
692a186c9d USB: expand autosuspend/autoresume API
This patch (as814) adds usb_autopm_set_interface() to the autosuspend
API.  It also provides convenient wrapper routines,
usb_autopm_enable() and usb_autopm_disable(), for drivers that want
to specify directly whether autosuspend should be allowed.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00
Alan Stern
af4f76066d USB: autosuspend code consolidation
This patch (as813) gathers together common code for USB interface
autosuspend/autoresume. 

It also adds some simple checking at the time an autosuspend request
is made, to see whether the request will fail.  This way we don't
add a workqueue entry when it would end up doing nothing.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:29 -08:00
Luiz Fernando N. Capitulino
0c1ac4f25f USB: makes usb_endpoint_* functions inline.
We have no benefits of having the usb_endpoint_* functions as functions,
but making them inline saves text and data segment sizes:

text	   data	    bss	    dec	    hex	filename
14893634	3108770	1108840	19111244	1239d4c	vmlinux.func
14893185	3108566	1108840	19110591	1239abf	vmlinux.inline

 This is the result of a 2.6.19-rc3 kernel compiled with GCC 4.1.1 without
CONFIG_MODULES, CONFIG_CC_OPTIMIZE_FOR_SIZE, CONFIG_REGPARM options set.
USB support is fully enabled (while most of the other drivers are not),
and that kernel has most of the USB code ported to use the endpoint
functions.

That happens because a call to those functions are expensive (in terms
of bytes), while the function's size is smaller or have the same 'size' of
the call.

Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:29 -08:00
Luiz Fernando N. Capitulino
6f7cd44162 USB: yealink: Use usb_endpoint_* functions
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:29 -08:00
Luiz Fernando N. Capitulino
0472074748 USB: storage: Use usb_endpoint_* functions
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:29 -08:00
Luiz Fernando N. Capitulino
4d823dd21d USB: usbtest: Use usb_endpoint_* functions
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:29 -08:00
Luiz Fernando N. Capitulino
fc6e2544bd USB: usbnet: Use usb_endpoint_* functions
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:29 -08:00