Some people report that they need psmouse module unloaded
for suspend to ram/disk to work properly. Let's make port
cleanup behave the same way as driver unload.
This fixes "bad state" roblem on various HP laptops, such
as nx7400.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sk98lin is scheduled for removal in July 2007. This patch makes the
deprecation more obvious in the configuration interface. FWIW, Gentoo have
been shipping a patch very similar to this for a long time.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Andrew Morton <akpm@linux-foundation.org>
drivers/char/watchdog/machzwd.c: In function 'zf_ioctl':
drivers/char/watchdog/machzwd.c:327: warning: passing argument 1 of 'zf_ping' makes integer from pointer without a cast
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Comtrol Hostess SV-11 driver uses features from INET but doesn't depend on it.
The simple solution is to make it depend on INET as happens for the sealevel
driver.
Fixes bug #7930.
Signed-Off-By: Baruch Even <baruch@ev-en.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Start link negotiation in the open method. Previously it was started
on driver initialialization and shutdown on close so an ifdown would
have results in closing negotiation for good.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Nag message about planned sk98lin removal.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The b44 Enet control disable bit may take longer to clear on some
systems, so the loop count is increased with this patch. Functionality
is not compromised, but a debug message can be seen when the bit is not
cleared within the count value.
Thanks to Vasileios Lourdas who reported the problem.
Signed-off by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
By reading the MAC status register we can detect whether the MAC has
seen the PHY see link. This allows us to show the link properties before
the device is up in ethtool.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that 2.6.19 provides a proper implementation that saves MSI, PCI-E
config space, we can have the e1000 driver use those instead of it's
custom implementation.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use ARRAY_SIZE macro already defined in kernel.h for ATM
drivers.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: chas williams <chas@cmf.nrl.navy.mil>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The modifications and bug fixes noted below were done by Realtime Control
Works and Contemporary Control Systems, Inc, Jan 2005. They were
incorporated into the 2.6 kernel by Jeff Morrow of Sierra Analytics, Feb
2007. <jmorrow@massspec.com>
The changes have been tested on a Contemporary Controls PCI20U-4000.
Summary of changes:
Arc-rawmode.c:
rx():
- Fixed error in received packet lengths; 256 byte packets were
being received as 257 bytes packets.
prepare_tx():
- Fixed error in transmit length calcs; 257 byte packets were being
transmitted as 260 byte packets.
com20020.c:
com20020_check():
- We now load the SETUP2 register if the 'clockm' parameter is
non-zero, instead of checking for ARC_CAN_10MBIT. The user is
now responsible for whether or not SETUP2 is loaded. If the
clock multiplier is non-zero, this means that the user wants a
baud rate greater than 2.5Mbps. This is not possible unless the
SETUP2 register is present (COM20020D, or COM20022). So, we're
relying on the user to be smart about what kind of chip he's
dealing with...
com20020-pci.c
- Added several entries to com20020pci_id_table[].
Signed-off-by: Jeff Morrow <jmorrow@massspec.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the experimental tag for the pcnet32 NAPI implementation.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove spin_lock_irqsave() around mii_ethtool_gset, mii_ethtool_sset
and generic_mii_ioctl. These are unnecessary and harmful because
the mii calls may call back into the mdio functions, which may sleep.
Pointed out by David Brownell.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't drop oversize frame it might be a VLAN (untagged).
Use different counter for fifo overrun vs fifo error.
Print error on fifo overrrun.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit timeout code could hang, and it would not clear out
problems if the hardware was stuck. Change the code to effectively do
a device down/up similar to the suspend/resume code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Yukon-FE chip doesn't do gigabit and has a differen PHY internally.
On this chip, phy status register doesn't properly reflect the result
of flow control negotiation. To workaround the problem and avoid having
to have so much chip dependent code; compute the result of flow control
by looking at the local and remote advertised bits.
Signed-off-by: Stephen Hemmminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resetting the pause bits on shutdown is not necessary.
The code was inherited from the vendor driver, and it is currently #ifdef'd
out there as well.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't mark pause frames as errors. This problem caused transmitter not
to pause and would effectively take out a gigabit switch because the
it can't handle overrun.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix copyrights in the cxgb3 driver.
Remove the Open Grid Computing copyright. It shouldn't be there.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was hardly necessary to repeat most of the code from gfar_error() in
gfar_interrupt(), especially having some inconsistencies between the two.
So, make the gfar_interrupt() just call gfar_error(), and not acknowledge
the interrupts itself as gfar_{receive/transmit/error}() do it anyway.
While at it, also clarify/cleanup debug messages in gfar_error()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert pci_module_init() to pci_register_driver().
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add device id for the Attansic L1 chip to pci_ids.h, then use it.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unused define from atl1_main.c.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some Asus motherboards containing the L1 NIC, the MAC address is
written by the BIOS directly to the MAC register during POST, and is
not stored in eeprom. If we don't succeed in fetching the MAC address
from eeprom or spi, try reading it directly from the MAC register.
Suggested by Xiong Huang.
And do some cleanup while we've got the hood up...
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
An ioread32 statement reads the wrong address. Fix it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The atl1 driver doesn't need NET_PCI. Remove it from Kconfig.
Noticed by Chad Sprouse.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes include:
* New support for 88e1145
* New support for 88e111s
* Fixing 88e1101 driver to not match non-88e1101 PHYs
* Increases in feature support across Marvell PHY product line
* Fixes a bunch of whitespace issues found by Lindent
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix the various misspellings of "agressive", as well as a couple
other things on the same lines while we're there.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Delete the definition of the unused FIND_FIRST_BIT() macro.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The line :
hp->Mode &= !RIO_PCI_INT_ENABLE;
is obviously wrong as RIO_PCI_INT_ENABLE=0x04 and is used as a bitmask
2 lines before. Getting no IRQ would not disable RIO_PCI_INT_ENABLE
but rather RIO_PCI_BOOT_FROM_RAM which equals 0x01.
Obvious fix is to change ! for ~.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
A "modprobe ohci1394; sleep 1.5; modprobe -r ohci1394" could get stuck
in uninterruptible state, especially if an external node was connected.
http://bugzilla.kernel.org/show_bug.cgi?id=7792
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This implements the simultaneous read of the isochronous cycle timer and
the system clock (in usecs). This allows to express the exact receive
time of an ISO packet as a system time with microsecond accuracy.
http://bugzilla.kernel.org/show_bug.cgi?id=7773
The counterpart patch for libraw1394 can be found at
http://thread.gmane.org/gmane.linux.kernel.firewire.devel/8934
Patch update (Stefan R.): Disable preemption and local interrupts.
Prevent integer overflow. Add paranoid error checks and kerneldoc to
hpsb_read_cycle_timer. Move it to other ieee1394_core high-level API
functions. Change comments. Adjust whitespace. Rename struct
_raw1394_cycle_timer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Pieter Palmers <pieterp@joow.be>
Acked-by: Dan Dennedy <dan@dennedy.org>
* since ide_hwif_t.ide_dma_host_on is called either when drive->using_dma == 1
or when return value is discarded make it void, also drop "ide_" prefix
* make __ide_dma_host_on() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_on() to atiixp_dma_host_on()
and sgiioc4_ide_dma_host_on() to sgiioc4_dma_host_on().
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
-1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
0 when DMA needs to be enabled (== need to call ->ide_dma_on)
1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All users of ->mmio == 1 are gone so convert ->mmio into flag.
Noticed by Alan Cox.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_use_fast_pio() helper for use by host drivers
* add DMA capability and hwif->autodma checks to ide_use_dma()
- au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)
[ for the IT8211/2 in SMART mode this check shouldn't be made but since
in it821x_fixups() we set DMA bit explicitly:
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
We need to set the bits so that the IDE layer knows
LBA28. LBA48 and DMA ar valid */
id->capability |= 3; /* LBA28, DMA */
we are better off using generic helper if we can ]
- ide-cris driver didn't set ->autodma
[ before the patch hwif->autodma was only checked in the chipset specific
hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
function so there no behavior change here ]
v2:
* updated patch description (thanks to Alan Cox for the feedback)
v3:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In cmd64x, siimage and scc_pata drivers:
* don't set drive->init_speed as it should be already
set by successful execution of ide_set_xfer_rate()
* use hwif->speedproc functions directly
Above changes allows removal of EXPORT_SYMBOL_GPL(ide_set_xfer_rate).
v2:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This field is no longer used by the core IDE code so fix ide-{disk,floppy}
drivers to keep openers count in the driver specific objects and remove
it from ide-{cd,scsi,tape} drivers (it was write-only).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove bogus comment for sis5513_config_xfer_rate()
* there is no need to call config_drive_art_rwp() because
it is called by config_art_rwp_pio()
* remove needless wrapper
* remove stale "TODO" comment
(IDE core should provide generic tuning code)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* disable DMA masks if no_piix_dma is set and remove now
not needed no_piix_dma_check from piix_config_drive_for_dma()
* there is no need to read register 0x55 in init_hwif_piix()
* move cable detection code to piix_cable_detect()
* remove unreachable 82371MX code from init_hwif_piix()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove redundant svwks_ide_dma_end() [ __ide_dma_end() is used by default ]
* remove init_dma_svwks() so the default ide_setup_dma() function is used
[ init_setup_csb6() takes care of not initializing disabled channels ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* BUG() on unknown DMA mode in cs5530_config_dma()
* there is no need to call hwif->ide_dma_host_{off,on}() in
cs5530_config_dma() because hwif->ide_dma_host_{off,on}()
is called by hwif->ide_dma_off_{quietly,on}()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In drivers/ide/Kconfig BLK_DEV_TRM290 depends on
BLK_DEV_IDEDMA_PCI (on which is BLK_DEV_IDEDMA dependant on).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is the patch (based on 2.6.19-rc4) for PATA controller of
Toshiba Cell reference set(Celleb). The reference set consists
of Cell, 512MB memory, Super Companion Chip(SCC) and some
peripherals such as HDD, GbE, etc. You can see brief explanation
and picture of Cell reference set at following URLs.
http://www.toshiba.co.jp/about/press/2005_09/pr2001.htmhttp://cell-industries.com/toshiba_announces.php
We use a drivers/ide driver because its design is more suitable for
SCC IDE controller than libata driver. Since SCC supports only 32bit
read/write, we must override many callbacks of ata_port_operations
by modifying generic helpers. Each time the libata common code is
updated, we must update those modified helpers. It is very hard for us.
But we will try to implement the libata driver as needed.
Signed-off-by: Kou Ishizaki <kou.ishizaki at toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi at toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix a number of issues with the DMA support code:
- driver claims support for all SW/MW DMA modes while supporting only MWDMA2;
- ide_dma_check() method tries to enable DMA on the "known good" drives which
don't support MWDMA2;
- ide_dma_on() method upon failure to set drive to MWDMA2 re-tunes already
tuned PIO mode and calls ide_dma_off() method instead of returning error;
- ide_dma_off() method sets drive->current_speed while it doesn't actually
change (only the PIO timings are re-loaded into the chip's registers);
- init_hwif() method forcibly sets/resets both "drive DMA capable" bits while
this is properly handled by ide_dma_{on,off}() methods being called later...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the driver's tuneproc() method to always set the PIO mode requested and not
pick the best possible one, rename it to pdc202xx_tune_drive(), and change the
calls to it accordingly; remove the preceding comment which has nothing to do
with the code.
Sergei Shtylyov wrote:
> The tuneproc() method should take arg 255 for auto-selecting the best PIO
> mode, not 5 as it did here + this driver's method always auto-selected instead
> of setting the mode it's been told to -- issue typical to drivers/ide/...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix two typos found by SiI680A documentation check. They caused the taskfile
transfer overclocking:
- in PIO mode 1 as 0x2283 must be used for both data and taskfile transfers;
- in PIO mode 2 as data and taskfile timings are swapped when writing to the
MMIO regs.
Fix coding style and trailing whitespace in enclosing statements while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drivers/ide/pci/siimage.c | 59 ++++++++++++++++++++++------------------------
1 file changed, 29 insertions(+), 30 deletions(-)
patch 2/2:
Remove clearing bmdma status from cdrom_decode_status() since ATA devices
might need it as well.
(http://lkml.org/lkml/2006/12/4/201 and http://lkml.org/lkml/2006/11/15/94)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
patch 1/2 (revised):
- Fix drive->waiting_for_dma to work with CDB-intr devices.
- Do the dma status clearing in ide_intr() and add a new
hwif->ide_dma_clear_irq for Intel ICHx controllers.
Revised per Alan, Sergei and Bart's advice.
Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters.
Please review/apply, thanks.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
A ZIP or similar with unformatted media will cause crashes when attempts
are made to read/write it in some cases. This is because bs_factor is
zero and we divide by it causing an oops.
As the size of a non-accessible/non-existant media is really a bit of a
zen question it doesn't matter if non-existant media is 512 bytes per
sector or zero. Setting it to 1 causes us to generate 512 bytes/sector
accesses and error properly.
Based on a fix found lurking in an ancient bugzilla entry since about 2004 (ugghhh)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* atiixp: if DMA can't be used atiixp_config_drive_for_dma() should return 0,
atiixp_dma_check() will tune the correct PIO mode anyway
* jmicron: if DMA can't be used config_chipset_for_dma() should return 0,
micron_config_drive_for_dma() will tune the correct PIO mode anyway
config_jmicron_chipset_for_pio(drive, !speed) doesn't program
device transfer mode for speed != 0 (only wastes some CPU cycles
on ide_get_best_pio_mode() call) so remove it
* triflex: if DMA can't be used triflex_config_drive_for_dma() should return 0,
triflex_config_drive_xfer_rate() will tune correct PIO mode anyway
Above changes also fix (theoretical) issue when ->speedproc fails to set
device transfer mode (i.e. when ide_config_drive_speed() fails to program it)
but one of DMA transfer modes is already enabled on the device by the BIOS.
In such scenario ide_dma_enable() will incorrectly return true statement
and ->ide_dma_check will try to enable DMA on the device.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remember to clear reg2 bits for the current device before setting mode
* remove no longer needed hpt34x_clear_chipset()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
register_platform_device_simple returns ERR_PTR(foo), so test it with
IS_ERR(foo).
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_unload_table_id() is always returning an error status.
Also, once the matching table is found, don't bother looking
for another match.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The AT91SAM9261 needs to activate an AHB clock (HCK0) to use the USB Host
controller. Previously clock.c would just enable it at startup, but now
all the unused clocks are automatically disabled.
Based on patch from Nicolas Ferre.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds another usb id to the cp2101. It seems to work well.
Please apply, thanks.
Signed-off-by: Pozsar Balazs <pozsy@uhulinux.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a runtime codespace shrink: in most cases, platform devices should
put probe() should in the init section, and remove() in the exit section.
And I have no idea why the module init/exit routines were mismarked.
It also moves one function table into read-only data.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hmm, I noticed that support for one of the USB host-to-host cables
never got fully merged ... Kconfig wouldn't show it! Fixed.
Also, changed the CDC Subset default to 'y' so that more of these
cables will work out-of-the-box.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This cleans up some error handling paths in usbnet device probing;
one of them could cause oopsing, e.g. with some RNDIS devices.
It also removes some extraneous whitespace.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Sitecom CN-124 device IDs to ALI M5632 usb host-to-host cable;
device IDs from Francois Barre <francois.barre@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
from: Kevin Lloyd <linux@sierrawireless.com>
This patch removes the Airprime 5220 device (branded as Audiovox) from
the option.c driver. This device is already supported by the sierra.c
driver.
This was based off of the option.c driver found in kernel 2.6.20-git11.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ps3_system_bus_driver_register is PS3 platform specific function.
On other platforms, it triggers WARN_ON in kref_get.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removes our GTCO CalComp Interwrite IPanels from the hid-core.c blacklist
because the HID Driver properly handles them.
Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is Joris' fixes reshuffelled and features renamed as David requested.
- acm_set_control is not mandatory, honour that
- throtteling is reset upon open
- throtteling is read consistently when processing input data
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB devices do have a configuration 0, in contravention of the
USB spec. Normally 0 is supposed to indicate that a device is
unconfigured.
While we can't change what the device is doing, we can change usbcore.
This patch (as852) allows usb_set_configuration() to accept a config
value of -1 as indicating that the device should be unconfigured. The
request actually sent to the device will still contain 0 as the value.
But even if the device does have a configuration 0, dev->actconfig
will be set to NULL and dev->state will be set to USB_STATE_ADDRESS.
Without some sort of special-case handling like this, there is no way
to unconfigure these non-compliant devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A SET_LINE_CODING control request should return a zero length packet
as an ACK to the host, during the status phase of a USB transaction.
The return value of gs_setup_class() is treated as the number of
bytes to write in the status phase of the control request, by
gs_setup(). For this case, the value returned by gs_setup_class should
be zero for SET_LINE_CODING but, right now, appears to be
sizeof(struct usb_cdc_line_coding).
However, if after doing the memcpy of the line coding descriptor we
set the variable "ret" to be zero, we should return the appropiate ZLP
to the host as an ACK in the status phase of the control request.
I've tested this out using Linux as both host and slave and confirmed
that the following small change fixes the spurious return of
sizeof(struct usb_cdc_line_coding)/wLength bytes in the status phase
of a USB_CDC_REQ_SET_LINE_CODING request. It's not a huge bug but, it
is worth fixing.
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device will not work as a mass storage device without US_FL_IGNORE_RESIDUE.
I bought this mp3 player that takes SD cards here
http://www.aiptek.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=AX4&Category_Code=MP3&Store_Code=AS
I can provide the errors in dmesg, if necessary, but this flag was
determined as necessary by doing a quick google on the errors that were
shown in dmesg.
Signed-off-by: Dylan Taft <d13f00l@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the misspelling of "USBNET_MII" to "USB_USBNET_MII".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add CIDC USB device to HID blacklist since it is actually a USB token
and has its own driver.
Signed-off-by: Zheng XiaoJun <zhengxiaojun@hsic.com.cn>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB_RTL8150 must select MII to avoid link errors.
Stolen from a patch by Randy Dunlap.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there's a USB mass storage device which exists in two version. One
reports the correct size and the other does not. Apart from that they
are identical and cannot be told apart. Here's a heuristic based on the
empirical finding that drives have even sizes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
as the skeleton driver was made ready for autosuspend a race condition
was introduced. The reference to get device must be gotten before the
autosuspend counter is upped, as this operation may sleep, dropping BKL.
Dropping BKL means that the pointer to the device may become invalid.
Here's the fix.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch fixes endian issues in asix_tx_fixup() that prevented
AX88772 and AX88178 devices from working on big-endian systems. With
the attached patch, all three chips are reported to work on big endian.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as849) fixes a bug in the USB hub driver. A single
pre-allocated buffer is used for all port status reads, but nothing
guarantees exclusive use of the buffer. A mutex is added to provide
this guarantee.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up the error processing path: in usb_submit_urb failed, we forgot
to free buffers. Also, don't free buffers in read callback: less error
prone, 21 LOC less, no need to comment so much. N.B. write path is ok
to do kfree.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as848) adds a useful little debugging message to let us
know when ehci-hcd's bus_suspend method runs. The other HCDs have
similar messages; now ehci-hcd doesn't need to feel left out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as847) makes some small changes to the hub driver's
suspend method:
For root hubs, the status URB should be unlinked and other
activity stopped _before_ the bus_suspend method is called.
The test for hdev->bus being NULL has been removed, since
it can never succeed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace the apparent typo CONFIG_USB_CDCETHER with
CONFIG_USB_NET_CDCETHER.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I added two fields to struct usb_serial_port to keep track of the
throttle state. Other usb-serial drivers typically use private data for
such things, but the generic driver can not really do that because some
of its code is also used by other drivers (which may have their own
private data needs).
As it is, I am not sure that this patch is useful in all scenarios.
It is certainly helpful for low-bandwidth devices that can hold their
data in response to throttling. But for devices that pump data in
real-time as fast as possible (webcam, A/D converter, etc), throttling
may actually cause more data loss.
From: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as846) adds the IGNORE_RESIDUE flag to the unusual_devs
entry for Sony-Ericsson's P990i phone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hi, one of my users has two USB hard drives that need the following
patch, otherwise there are I/O errors similar to those here:
http://bugme.osdl.org/show_bug.cgi?id=3223
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in devices.c we have a piece of code for dealing with losing in a race.
If we indeed lose the race we don't care whether our own memory allocation
worked. The check for that is so early that we return early even if we
don't have to.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
init_endpoint_class calls class_create, and checks the result for an error
with IS_ERR; however, if true, it then returns the result of IS_ERR (a
boolean) rather than PTR_ERR (the actual errno).
Signed-off-by: Josh Triplett <josh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A simple driver to turn on the charging capability of a USB BlackBerry
device when it is plugged into the machine. It does not bind to the
device, so all userspace programs can still sync properly with it.
Note, if CONFIG_USB_SUSPEND is enabled, it can play havoc with this
device as the power to the port will be shut down. This device id will
have to be added to the global blacklist table when it is created.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as850b) disables remote wakeup (and everything else!) on
all EHCI ports when the shutdown() method is called. If remote wakeup
is left active then some systems will reboot instead of powering off.
This fixes Bugzilla #7828.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The static rate from the path record should be put into the address
vector -- a long time ago the rate in the address attributes needed to
be a relative rate, which required more munging, but now that the
conversion from absolute to relative is done in the low-level driver,
it's easy for ib_init_ah_from_path() to put the absolute rate in.
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export the numa-node attribute of PCI devices in sysfs so that
user applications may choose where to be placed accordingly.
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm currently working on a port to a CPCI board with a MPC5200. When
testing the PCI interrupt routing, I discovered the following: Even devices
which don't use interrupts (-> PCI Spec.: Interrupt Pin Register is zero),
get an interrupt assigned (this is at least true for most of the
PPC-targets I looked at).
The cause is pretty obvious in drivers/pci/setup-irq.c. I guess at least
in an ideal world with correctly designed hardware, the code should rather
look as in the patch below.
Of course it doesn't hurt anybody to have an unuseable IRQ assigned to a
PCI-to-PCI-bridge (or something alike), but to me it seems a bit strange.
Please correct me, if I'm mislead.
The patch below is tested on the above mentioned CPCI-MPC5200 board and is
compiler tested with the latest git-repository kernel on x86.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CARDBUS_MEM_SIZE was increased to 64MB on 2.6.20-rc2, but larger size might
result in allocation failure for the reserving itself on some platforms
(for example typical 32bit MIPS). Make it (and CARDBUS_IO_SIZE too)
customizable by "pci=" option for such platforms.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As found on some arm defconfigs.
I only looked at how original patch changes things and other patches fix
compilation. ;-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up the coding in device_add_attrs() a bit.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch that removes all redundant kobject_unregister argument checks.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extend rdma_cm to support multicast communication. Multicast support
is added to the existing RDMA_PS_UDP port space, as well as a new
RDMA_PS_IPOIB port space. The latter port space allows joining the
multicast groups used by IPoIB, which enables offloading IPoIB traffic
to a separate QP. The port space determines the signature used in the
MGID when joining the group. The newly added RDMA_PS_IPOIB also
allows for unicast operations, similar to RDMA_PS_UDP.
Supporting the RDMA_PS_IPOIB requires changing how UD QPs are initialized,
since we can no longer assume that the qkey is constant. This requires
saving the Q_Key to use when attaching to a device, so that it is
available when creating the QP. The Q_Key information is exported to
the user through the existing rdma_init_qp_attr() interface.
Multicast support is also exported to userspace through the rdma_ucm.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB SA tracks multicast join/leave requests on a per port basis and
does not do any reference counting: if two users of the same port join
the same group, and one leaves that group, then the SA will remove the
port from the group even though there is one user who wants to stay a
member left. Therefore, in order to support multiple users of the
same multicast group from the same port, we need to perform reference
counting locally.
To do this, add an multicast submodule to ib_sa to perform reference
counting of multicast join/leave operations. Modify ib_ipoib (the
only in-kernel user of multicast) to use the new interface.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_cm_alloc_rx_skb() might be called from IRQ context, so it must
use dev_kfree_skb_any(), not kfree_skb().
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the Open Grid Computing copyright. It shouldn't be there.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For T3B devices, mark user QP in error once we transition
to TERMINATE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iwcm iw_cm_id destruction race condition fixes:
- iwcm_deref_id() always wakes up if there's another reference.
- clean up race condition in cm_work_handler().
- create static void free_cm_id() which deallocs the work entries and then
kfrees the cm_id memory. This reduces code replication.
- rem_ref() if this is the last reference -and- the IWCM owns freeing the
cm_id, then free it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Acked-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the port phys state as returned from ehca_query_port() to LINK_UP.
ehca actually represents a logical HCA, whose phys/link state always
is LINK_UP.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
