* 'at91-3.4-cleanup2+DT' of git://github.com/at91linux/linux-at91: (22 commits)
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
ARM: at91/tclib: take iomem size from resource
ARM: at91/pit: add traces in case of error
ARM: at91: pit add DT support
ARM: at91: AIC and GPIO IRQ device tree initialization
ARM: at91/board-dt: remove AIC irq domain from board file
ARM: at91/gpio: remove the static specification of gpio_chip.base
ARM: at91/gpio: add .to_irq gpio_chip handler
ARM: at91/gpio: non-DT builds do not have gpio_chip.of_node field
ARM: at91/gpio: add irqdomain and DT support
ARM: at91/gpio: change comments and one variable name
ARM/USB: at91/ohci-at91: remove the use of irq_to_gpio
...
These two branches are a dependency for the at91 device tree changes,
so we pull them in here. at91/base2+cleanup will get merged through
the arm-soc cleanup2 branch, while the irqdomain tree will be sent
by Grant before this one gets integrated.
Conflicts:
drivers/rtc/rtc-at91sam9.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Transfer resource index is cleared in hardware when XFERCOMPLETE
event is generated, so clear the driver's res_trans_idx variable
immediately after that event is received. The upcoming hibernation
patches depend on this change.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_ep_set_wedge() and dwc3_gadget_set_selfpowered() were
modifying dwc->flags/dwc->is_selfpowered without taking the lock.
Since those modifications are non-atomic, that could cause other
flags to be corrupted. Fix them both to take the lock.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The loop in dwc3_gadget_set_link_state() was using a udelay(500),
which is a long time to delay in interrupt context. Change it to
udelay(5) and increase the loop count to match.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_pci_probe() would return success even if the calls to
dwc3_get_device_id() or platform_device_alloc() fail, fix that.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Define DWC3_GCTL_SCALEDOWN_MASK and use it in place of
DWC3_GCTL_SCALEDOWN(3).
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Zero is a valid value for a microframe number. So remove the bogus
test for non-zero in dwc3_gadget_start_isoc().
Cc: stable@vger.kernel.org
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's wrong to use the size of array as an argument for strncat.
Memory corruption is possible. strlcat is exactly what we need here.
Cc: stable@vger.kernel.org
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we have a non-ISOC endpoint, we will not have a Link TRB
pointing to the beginning of the TRB pool. On such endpoints,
we don't want to let the driver wrap around the TRB pool
otherwise controller will hang waiting for a valid TRB.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We always return zero instead of the id we found.
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/dwc3/core.c and drivers/usb/dwc3/dwc3-omap.c
included 'linux/module.h' twice, remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch enables to use devm_xxx functions during probing driver.
The devm_xxx series functions are able to release resource when the
driver is detatched. We can remove several codes to release resources
in the probe function.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds Exynos Specific Glue layer to support USB peripherals
on Samsung Exynos5 chips.
[ balbi@ti.com : prevent compilation of Exynos glue layer
on platforms which don't provide clk API implementation ]
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's really no point in having hcd->irq as a
signed integer when we consider the fact that
IRQ 0 means NO_IRQ. In order to avoid confusion,
make hcd->irq unsigned and fix users who were
passing -1 as the IRQ number to usb_add_hcd.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BeagleBone changed to the default FTDI 0403:6010 id in rev A5 to make life
easier for Windows users, so we need a similar workaround as the Calao
board to support it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RR+f
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: Gadget: changes for 3.4
This merge is rather big. Here's what it contains:
For am5536udc we have just simple coding style fixes. Nothing that has any
potential to cause any issues going forward.
With mv_udc, there's only one single change removing an unneeded NULL check.
at91_udc also only saw a single change this merge window, and that's only
removing a duplicated header.
The Renesas controller has a few more involved changes. Support for SUDMAC was
added, there's now a special handling of IRQ resources for when the IRQ line is
shared between Renesas controller and SUDMAC, we also had a bug fix where
Renesas controller would sleep in atomic context while doing DMA transfers from
a tasklet. There were also a set of minor cleanups.
The FSL UDC also had a scheduling in atomic context bug fix, but that's all.
Thanks to Sebastian, the dummy_hcd now works better than ever with support for
scatterlists and streams. Sebastian also added SuperSpeed descriptors to the
serial gadgets.
The highlight on this merge is the addition of a generic API for mapping and
unmapping usb_requests. This will avoid code duplication on all UDC controllers
and also kills all the defines for DMA_ADDR_INVALID which UDC controllers
sprinkled around. A few of the UDC controllers were already converted to use
this new API.
Conflicts:
drivers/usb/dwc3/gadget.c
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WiB6
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: transceiver changes for 3.4
Here we have a big rework done by Heikki Krogerus (thanks) which
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
a patch making modules behave better, there's a fix on debugfs'
error path, a small change removing an unnecessary pm_runtime
call on musb_shutdown() and a fix to relesect the endpoint in
Interrupt context.
This last patch is needed because we must drop musb's lock when
calling request->complete() and that could cause problems if another
thread queues a request and ends up changing MUSB_INDEX register.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPTeh0AAoJEIaOsuA1yqRECs8QAIdTAaawlPbA3HeTmMXDAQw7
5gYyrxbNmiHMFMHOuy8M10NO3ID2RH79+sXJjlNdmN10M5vZa5vcFs3rLiT9yPis
a4SsaH7JrdqPViD1vqSjaEIymx7tMyq1U/ohP9tkf2H6wUkf9oif+todzSiZqRPM
Jdt0Zu5sNwnxyr3XzsXHEH4jdzkLro/SL5JYUmfhZMxOg51s6ORr6RA/W+/Wo5a2
3lFXjeOoGARfx0/9N/3TT7205qPthdTa0Y7Xh9WzSxPln0UdCFKYok0o2hR8TF9g
+WvK6OKJ9ETe6oBpiQsbEw8RknJo+Px+Nn/8tOua7xJ/uSlbNrK9G7TfVvy0cCQt
5P6b6ccCclxDG0ckGHE+KiAJ1MuqTkdq4DiX52aqZU23do8n8L/HSAQDaNCICLHD
+y/y0BbE4BokcBg1ndpaJvrBhLbeQQ+pLz+JjGvrSy5rsWeuku8yq4gEnJXDIFVx
SCmG5seafRyyNKPdJlPy+lzrDxj86t462MRWbnSNNULOP1W9slhduDQ3GGAjRplf
ELTkU40CPo74IsnG69cckhrvLojyIXomWlZQm9FwdgHrCWNMVy6dfVaWYjdCE5GQ
fmtuocG+9Puvujvgr51nY6wB7lKm13mqsdzeFE0+Dgg27W3qSfDISpSSfTrB6kEP
fnJ0p2zLXMKY8vXtKyHB
=2VXE
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: MUSB changes for 3.4
Here are a set of changes to the MUSB driver. In summary we have
a patch making modules behave better, there's a fix on debugfs'
error path, a small change removing an unnecessary pm_runtime
call on musb_shutdown() and a fix to relesect the endpoint in
Interrupt context.
This last patch is needed because we must drop musb's lock when
calling request->complete() and that could cause problems if another
thread queues a request and ends up changing MUSB_INDEX register.
irq_to_gpio() macro will be removed from AT91 GPIO interrupt
controller. So we replace it with the use of gpio_to_irq()
and a reworked test.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-usb@vger.kernel.org
This reverts commit 79857e8e7b.
To quote Shengzhou Liu:
I'm sorry, please don't apply this patch.
It appears not only on P1022 platform.
There will be more breaks on other platforms regarding
CTRL_PHY_CLK_VALID bit.
I will post a new patch with well compatibility on all
platforms as soon as I get necessary confirmations.
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the first cut at a driver for the Fintek F81232 USB to serial
single port converter. This provides the initial framework for the
device, and some data can move through it, but no line settings are
handled, so it's not that useful yet. It does give people a starting
place to work from.
Thank to Fintek for providing samples and specifications, without which,
this driver would have never been able to be written.
Cc: Amanda Ying <Amanda_Ying@fintek.com.tw>
Cc: Tom Tsai <Tom_Tsai@fintek.com.tw>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the zio.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the whiteheat.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Support Department <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the vivopay-serial.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the usb_debug.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the symbolserial.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the ssu100.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the spcp8x5.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the sierra.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the siemens_mpi.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the qcserial.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Steven Hardy <shardy@redhat.com>
CC: Thomas Tuttle <ttuttle@chromium.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the qcaux.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the oti6858.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the option.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the opticon.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the omninet.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the navman.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the moto_modem.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Elizabeth Jennifer Myers <elizabeth@sporksirc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the mos7840.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the mos7720.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the mct_u232.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the kobil_sct.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Jiri Slaby <jslaby@suse.cz>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the kl5kusb105.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the keyspan_pda.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the keyspan.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the iuu_phoenix.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the ipw.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Oliver Neukum <oneukum@suse.de>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the io_ti.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Lucas De Marchi <lucas.demarchi@profusion.mobi>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the io_edgeport.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Huzaifa Sidhpurwala <huzaifas@redhat.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the hp4x.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the garmin_gps.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the funsoft.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the empeg.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Gary Brubaker <xavyer@ix.netcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the digi_acceleport.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Peter Berger <pberger@brimson.com>
CC: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the cypress_m8.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Lonnie Mendez <dignome@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the cyberjack.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the cp210x.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: "Malte Schröder" <maltesch@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the ch341.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the belkin_sa.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the ark3116.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the aircable.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Lucas De Marchi <lucas.demarchi@profusion.mobi>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that Alan Stern has cleaned up the usb serial driver registration,
we have the ability to create a module_usb_serial_driver macro to make
things a bit simpler, like the other *_driver macros created.
But, as we need two functions here, we can't reuse the existing
module_driver() macro, so we need to roll our own.
Here's a patch implementing module_usb_serial_driver() and it converts
the pl2303 driver to use it, showing a nice cleanup.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This replaces the remaining defines which are available in "public"
include/ directory and are re-defined by the storage gadget.
This is patch is basicaly search & replace followed by the removal of
the defines.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
US_BULK_FLAG_IN is defined as 1 and not used. The USB storage spec says
that bit 7 of flags within CBW defines the data direction. 1 is DATA-IN
(read from device) and 0 is the DATA-OUT. Bit 6 is obselete and bits 0-5
are reserved.
This patch redefines the unsued define US_BULK_FLAG_IN from 1 to 1 << 7
aka 0x80 and replaces the obvious users. In a following patch the
storage gadget will use it as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the BOT data structures for CBW and CSW from drivers internal
header file to global include able file in include/.
The storage gadget is using the same name for CSW but a different for
CBW so I fix it up properly. The same goes for the ub driver and keucr
driver in staging.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checking of CTRL_PHY_CLK_VALID bit break on some platform on which
there is not USB CTRL_PHY_CLK_VALID bit.
- P1023/P3041/P5020 etc,have this bit
- P3060/4080/PSC913x do have this bit, but not mentioned in RM.
- P1022(perhaps and other) has no this bit
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shows up on ia64 builds (and possibly elsewhere) for configs that
don't set PM_RUNTIME or PM_SLEEP as follows:
drivers/usb/core/hcd-pci.c:383:12: warning: 'suspend_common' defined but not used
drivers/usb/core/hcd-pci.c:438:12: warning: 'resume_common' defined but not used
As per above, the functions are only used if RUNTIME/SLEEP are set,
so make the two functions conditional on these Kconfig values.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some misconfigured ftdi_sio devices, if the manufacturer string is
NULL, the kernel will oops when the device is plugged in. This patch
fixes the problem.
Reported-by: Wojciech M Zabolotny <W.Zabolotny@elka.pw.edu.pl>
Tested-by: Wojciech M Zabolotny <W.Zabolotny@elka.pw.edu.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
those routines have everything we need to map/unmap
USB requests and it's better to use them.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
those routines have everything we need to map/unmap
USB requests and it's better to use them.
In order to achieve that, we had to add a simple
change on how we allocate and use our setup buffer;
we cannot allocate it from coherent anymore otherwise
the generic map/unmap routines won't be able to easily
know that the GetStatus request already has a DMA
address.
Signed-off-by: Felipe Balbi <balbi@ti.com>
such utilities are currently duplicated on all UDC
drivers basically with the same structure. Let's group
all implementations into one generic implementation
and get rid of that duplication.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use DEFINE_PCI_DEVICE_TABLE instead of "const struct pci_device_id".
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.
Includes fixes to IMX code from Sascha Hauer.
[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.
Includes fixes from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
[ balbi@ti.com : fixed a compile error on isp1704_charger.c ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds new device IDs to the ftdi_sio module to support
the new Sealevel SeaLINK+8 2038-ROHS device.
Signed-off-by: Scott Dial <scott.dial@scientiallc.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This ehci driver is mainly designed to support host controller found on
Marvell PXA and MMP Soc series.
Add the dependence to avoid the potential build failure which may
include two EHCI controller drivers.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes uses of hcd->state and replaces hcd->state with
ohci->rh_state field.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__do_config_autodelink passes the data variable to the transport function.
If the calling functions pass a stack variable, this will eventually trigger
a DMA-API debug backtrace for mapping stack memory in the DMA buffer. Fix
this by calling kmemdup for the passed data instead.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If USB UTMI PHY is not enable, writing to portsc register will lead to
kernel hang during boot up.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When build i.mx platform with imx_v6_v7_defconfig, and after adding
USB Gadget support, it has below build error:
CC drivers/usb/host/fsl-mph-dr-of.o
drivers/usb/host/fsl-mph-dr-of.c: In function 'fsl_usb2_device_register':
drivers/usb/host/fsl-mph-dr-of.c:97: error: 'struct pdev_archdata'
has no member named 'dma_mask'
It has discussed at: http://www.spinics.net/lists/linux-usb/msg57302.html
For PowerPC, there is dma_mask at struct pdev_archdata, but there is
no dma_mask at struct pdev_archdata for ARM. The pdev_archdata is
related to specific platform, it should NOT be accessed by
cross platform drivers, like USB.
The code for pdev_archdata should be useless, as for PowerPC,
it has already gotten the value for pdev->dev.dma_mask at function
arch_setup_pdev_archdata of arch/powerpc/kernel/setup-common.c.
Tested-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the usb_disabled() check to the probe function and get rid of the
rather pointless message on module load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had a user report that running setserial on /dev/ttyACM0 didn't work.
He pointed at an old patch by Oliver Neukum from 2008 that never went anywhere..
http://permalink.gmane.org/gmane.linux.usb.general/9236
I made some minor changes to get it to apply again, and got the user to retest on 3.1,
and he reported it worked for him. https://bugzilla.redhat.com/show_bug.cgi?id=787607
The diff below is against 3.3rc. The only difference between this and
the version the user tested is the removal of the if (!ACM_READY) test
Havard removed ACM_READY in 99823f457d
I'm unclear if there's need for a different test in its place.
From: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a MPC8xxx was being used, 'have_sysif_regs' should be set and
it should setup cache snooping for all the 4GB space on both PPC32
and PPC64.
Signed-off-by: Pan Jiafei <Jiafei.Pan@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WDM_READ flag is cleared later iff desc->length is reduced to 0.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ehci-mv.c can cover Marvell PXA and MMP series including PXA168,
so this driver seems redundant now.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Cc: <tanmay.upadhyay@einfochips.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We must not allow the input buffer length to change while we're
shuffling the buffer contents. We also mustn't clear the WDM_READ
flag after more data might have arrived. Therefore move both of these
into the spinlocked region at the bottom of wdm_read().
When reading desc->length without holding the iuspin lock, use
ACCESS_ONCE() to ensure the compiler doesn't re-read it with
inconsistent results.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gobi 1000 devices have a different port layout, which wasn't respected
by the current driver, and thus it grabbed the QMI/net port. In the
near future we'll be attaching another driver to the QMI/net port for
these devices (cdc-wdm and qmi_wwan) so make sure the qcserial driver
doesn't claim them. This patch also prevents qcserial from binding to
interfaces 0 and 1 on 1K devices because those interfaces do not
respond.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No one uses them anymore, they should be using the safer
usb_serial_register_drivers() and usb_serial_deregister_drivers()
functions instead.
Thanks to Alan Stern for writing these functions and porting all
in-kernel users to them.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was missed in Alan's last round of conversions.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1529) modifies the following usb-serial drivers to
utilize the new usb_serial_{de}register_drivers() routines:
ti_usb_3410_5052, usb_debug, visor, vivopay-serial,
whiteheat, and zio.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1528) modifies the following usb-serial drivers to
utilize the new usb_serial_{de}register_drivers() routines:
qcaux, qcserial, safe_serial, siemens_mpi, sierra,
spcp8x5, ssu100, and symbolserial.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1527) modifies the following usb-serial drivers to
utilize the new usb_serial_{de}register_drivers() routines:
navman, omninet, opticon, option, oti6858, and pl2303.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1526) modifies the following usb-serial drivers to
utilize the new usb_serial_{de}register_drivers() routines:
keyspan, kl5kusb105, kobil_sct, mct_u232, mos7720,
mos7840, and moto_modem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1525) modifies the following usb-serial drivers to
utilize the new usb_serial_{de}register_drivers() routines:
io_edgeport, io_ti, ipaq, ipw, ir-usb, and iuu_phoenix.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1524) modifies the following usb-serial drivers to
utilize the new usb_serial_{de}register_drivers() routines:
digi_acceleport, empeg, ftdi_sio, funsoft, garmin_gps,
and hp4x.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1523) modifies the following usb-serial drivers to
utilize the new usb_serial_{de}register_drivers() routines:
aircable, ark3116, belkin_sa, ch341, cp210x, cyberjack,
and cypress_m8.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1522) adds two new routines to the usb-serial core, for
registering and unregistering serial drivers. Instead of registering
the usb_driver and usb_serial_drivers separately, with error checking
for each one, the drivers can all be registered and unregistered by a
single function call. This reduces duplicated code.
More importantly, the new core routines change the order in which the
drivers are registered. Currently the usb-serial drivers are all
registered first and the usb_driver is done last, which leaves a
window for problems. A udev script may quickly add a new dynamic-ID
for a usb-serial driver, causing the corresponding usb_driver to be
probed. If the usb_driver hasn't been registered yet then an oops
will occur.
The new routine prevents such problems by registering the usb_driver
first. To insure that it gets probed properly for already-attached
serial devices, we call driver_attach() after all the usb-serial
drivers have been registered.
Along with adding the new routines, the patch modifies the "generic"
serial driver to use them. Further patches will similarly modify all
the other in-tree USB serial drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb INDEX register is getting modified/corrupted during temporary
un-locking in a SMP system. Set this register with proper value
after re-acquiring the lock
Scenario:
---------
CPU1 is handling a data transfer completion interrupt received for
the CLASS1 EP
CPU2 is handling a CLASS2 thread which is queuing data to musb for
transfer
Below is the error sequence:
CPU1 | CPU2
--------------------------------------------------------------------
Data transfer completion inter- |
rupt recieved. |
|
musb INDEX reg set to CLASS1 EP |
|
musb LOCK is acquired. |
|
| CLASS2 thread queues data.
|
| CLASS2 thread tries to acquire musb
| LOCK but lock is already taken by
| CLASS1, so CLASS2 thread is
| spinning.
|
From Interrupt Context musb |
giveback function is called |
|
The giveback function releases | CLASS2 thread now acquires LOCK
LOCK |
|
ClASS1 Request's completion cal-| ClASS2 schedules the data transfer and
lback is called | sets the MUSB INDEX to Class2 EP number
|
Interrupt handler for CLASS1 EP |
tries to acquire LOCK and is |
spinning |
|
Interrupt for Class1 EP acquires| Class2 completes the scheduling etc and
the MUSB LOCK | releases the musb LOCK
|
Interrupt for Class1 EP schedul-|
es the next data transfer |
but musb INDEX register is still|
set to CLASS2 EP |
Since the MUSB INDEX register is set to a different endpoint, we
read and modify the wrong registers. Hence data transfer will not
happen properly. This results in unpredictable behavior
So, the MUSB INDEX register is set to proper value again when
interrupt re-acquires the lock
Cc: stable@vger.kernel.org
Signed-off-by: Supriya Karanth <supriya.karanth@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Reviewed-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When loading g_ether gadget, there is below message:
Backtrace:
[<80012248>] (dump_backtrace+0x0/0x10c) from [<803cb42c>] (dump_stack+0x18/0x1c)
r7:00000000 r6:80512000 r5:8052bef8 r4:80513f30
[<803cb414>] (dump_stack+0x0/0x1c) from [<8000feb4>] (show_regs+0x44/0x50)
[<8000fe70>] (show_regs+0x0/0x50) from [<8004c840>] (__schedule_bug+0x68/0x84)
r5:8052bef8 r4:80513f30
[<8004c7d8>] (__schedule_bug+0x0/0x84) from [<803cd0e4>] (__schedule+0x4b0/0x528)
r5:8052bef8 r4:809aad00
[<803ccc34>] (__schedule+0x0/0x528) from [<803cd214>] (_cond_resched+0x44/0x58)
[<803cd1d0>] (_cond_resched+0x0/0x58) from [<800a9488>] (dma_pool_alloc+0x184/0x250)
r5:9f9b4000 r4:9fb4fb80
[<800a9304>] (dma_pool_alloc+0x0/0x250) from [<802a8ad8>] (fsl_req_to_dtd+0xac/0x180)
[<802a8a2c>] (fsl_req_to_dtd+0x0/0x180) from [<802a8ce4>] (fsl_ep_queue+0x138/0x274)
[<802a8bac>] (fsl_ep_queue+0x0/0x274) from [<7f004328>] (composite_setup+0x2d4/0xfac [g_ether])
[<7f004054>] (composite_setup+0x0/0xfac [g_ether]) from [<802a9bb4>] (fsl_udc_irq+0x8dc/0xd38)
[<802a92d8>] (fsl_udc_irq+0x0/0xd38) from [<800704f8>] (handle_irq_event_percpu+0x54/0x188)
[<800704a4>] (handle_irq_event_percpu+0x0/0x188) from [<80070674>] (handle_irq_event+0x48/0x68)
[<8007062c>] (handle_irq_event+0x0/0x68) from [<800738ec>] (handle_level_irq+0xb4/0x138)
r5:80514f94 r4:80514f40
[<80073838>] (handle_level_irq+0x0/0x138) from [<8006ffa4>] (generic_handle_irq+0x38/0x44)
r7:00000012 r6:80510b1c r5:80529860 r4:80512000
[<8006ff6c>] (generic_handle_irq+0x0/0x44) from [<8000f4c4>] (handle_IRQ+0x54/0xb4)
[<8000f470>] (handle_IRQ+0x0/0xb4) from [<800085b8>] (tzic_handle_irq+0x64/0x94)
r9:412fc085 r8:00000000 r7:80513f30 r6:00000001 r5:00000000
r4:00000000
[<80008554>] (tzic_handle_irq+0x0/0x94) from [<8000e680>] (__irq_svc+0x40/0x60)
The reason of above dump message is calling dma_poll_alloc with can-schedule
mem_flags at atomic context.
To fix this problem, below changes are made:
- fsl_req_to_dtd doesn't need to be protected by spin_lock_irqsave,
as struct usb_request can be access at process context. Move lock
to beginning of hardware visit (fsl_queue_td).
- Change the memory flag which using to allocate dTD descriptor buffer,
the memory flag can be from gadget layer.
It is tested at i.mx51 bbg board with g_mass_storage, g_ether, g_serial.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixup below warning on device_unregister()
renesas_usbhs renesas_usbhs.1: host probed
renesas_usbhs renesas_usbhs.1: gadget probed
renesas_usbhs renesas_usbhs.1: irq request err
------------[ cut here ]------------
WARNING: at ${LINUX}/drivers/base/core.c:1)
Device 'gadget' does not have a release() function, it is broken and must be fi.
Modules linked in:
[<c000e25c>] (unwind_backtrace+0x0/0xe4) from [<c0016960>] (warn_slowpath_commo)
[<c0016960>] (warn_slowpath_common+0x4c/0x64) from [<c00169f8>] (warn_slowpath_)
[<c00169f8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c0185b80>] (device_release+0x)
[<c0185b80>] (device_release+0x70/0x84) from [<c013e300>] (kobject_cleanup+0x58)
[<c013e300>] (kobject_cleanup+0x58/0x6c) from [<c01cba14>] (usbhs_mod_gadget_re)
[<c01cba14>] (usbhs_mod_gadget_remove+0x3c/0x6c) from [<c01c8384>] (usbhs_mod_p)
[<c01c8384>] (usbhs_mod_probe+0x68/0x80) from [<c01c7f84>] (usbhs_probe+0x1cc/0)
...
Cc: stable@vger.kernel.org
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fix a bug in f_serial, which expect the ep->desc to be NULL after
disabling an endpoint.
Cc: stable@vger.kernel.org
Signed-off-by: Ido Shayevitz <idos@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is to pull in the xhci changes and the other fixes and device id
updates that were done in Linus's tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/gadget/at91_udc.c included 'linux/prefetch.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
.device_fc is added in struct dma_slave_config recently. All user drivers, which
want DMA to be the flow controller must pass this field as false. As earlier
driver don't look to use this feature, mark it false for now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This USB-serial cable with mini stereo jack enumerates as:
Bus 001 Device 004: ID 1a61:3410 Abbott Diabetes Care
It is a TI3410 inside.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1521b) fixes the interaction between usb-storage's
scanning thread and the freezer. The current implementation has a
race: If the device is unplugged shortly after being plugged in and
just as a system sleep begins, the scanning thread may get frozen
before the khubd task. Khubd won't be able to freeze until the
disconnect processing is complete, and the disconnect processing can't
proceed until the scanning thread finishes, so the sleep transition
will fail.
The implementation in the 3.2 kernel suffers from an additional
problem. There the scanning thread calls set_freezable_with_signal(),
and the signals sent by the freezer will mess up the thread's I/O
delays, which are all interruptible.
The solution to both problems is the same: Replace the kernel thread
used for scanning with a delayed-work routine on the system freezable
work queue. Freezable work queues have the nice property that you can
cancel a work item even while the work queue is frozen, and no signals
are needed.
The 3.2 version of this patch solves the problem in Bugzilla #42730.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes. The endpoint
descriptor has the NAK rate encoded in number of microframes. We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct. This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.
The fix is to use the correct encoding. Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.
This should be back ported to kernels as old as 2.6.31, that contain the
commit dfa49c4ad1 "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Suggested-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.
Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.
The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI. This allows the BIOS to access USB devices without
having xHCI support.
The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior. The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.
Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished. This will balance the ref counts in the PCI core. When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.
This should be back ported to kernels as old as 2.6.31. That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org
not all platforms will use all of those ehci_*
symbols on their hc_driver structure. Sometimes
we might need to provide a modified version of
a certain method or not provide it at all, as is
the case with OMAPs which don't support port handoff
feature.
Whenever we compile a kernel for an OMAP board with
EHCI enabled, we get compile warnings:
drivers/usb/host/ehci-hub.c:1079: warning: 'ehci_relinquish_port' \
defined but not used
drivers/usb/host/ehci-hub.c:1088: warning: 'ehci_port_handed_over' \
defined but not used
In order to cleanup those warnings, we're adding
__maybe_unused annotation to those functions.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a flexible USB Audio Class 2.0 compliant gadget driver that
implements a simple topology with a virtual sound card exposed at
the function side.
The driver doesn't expect any real audio codec to be present on the
function - the audio streams are simply sinked to and sourced from a
virtual ALSA sound card created. The user-space application may choose
to do whatever it wants with the data received from the USB Host and
choose to provide whatever it wants as audio data to the USB Host.
Capture(USB-Out) and Playback(USB-In) can be run at independent
configurations specified via module parameters while loading the driver.
Make this new version as the default selection by a new Kconfig choice.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move manufacturer and product string ids into audio.c so
as to be reusable by the new uac2 version of gadget driver.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The extant USB-Audio function driver complies to UAC_1 spec.
So name the files accordingly, paving way for inclusion of
a new UAC_2 specified driver.
Signed-off-by: Yadi Brar <yadi.brar01@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1. Remove all old mass-storage ids's pid:
0x0026,0x0053,0x0098,0x0099,0x0149,0x0150,0x0160;
2. As the pid from 0x1401 to 0x1510 which have not surely assigned to
use for serial-port or mass-storage port,so i think it should be
removed now, and will re-add after it have assigned in future;
3. sort the pid to WCDMA and CDMA.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that USB 3.0 hub remote wakeup on port status changes is enabled,
and USB 3.0 device remote wakeup is handled in the USB core properly,
let's turn on auto-suspend for all USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch takes care of the race condition between the Function Wake
Device Notification and the auto-suspend timeout for this situation:
Roothub
| (U3)
hub A
| (U3)
hub B
| (U3)
device C
When device C signals a resume, the xHCI driver will set the wakeup_bits
for the roothub port that hub A is attached to. However, since USB 3.0
hubs do not set a link state change bit on device-initiated resume, hub
A will not indicate a port event when polled. Without this patch, khubd
will notice the wakeup-bits are set for the roothub port, it will resume
hub A, and then it will poll the events bits for hub A and notice that
nothing has changed. Then it will be suspended after 2 seconds.
Change hub_activate() to look at the port link state for each USB 3.0
hub port, and set hub->change_bits if the link state is U0, indicating
the device has finished resume. Change the resume function called by
hub_events(), hub_handle_remote_wakeup(), to check the link status
for resume instead of just the port's wakeup_bits.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 hubs don't have a port suspend change bit (that bit is now
reserved). Instead, when a host-initiated resume finishes, the hub sets
the port link state change bit.
When a USB 3.0 device initiates remote wakeup, the parent hubs with
their upstream links in U3 will pass the LFPS up the chain. The first
hub that has an upstream link in U0 (which may be the roothub) will
reflect that LFPS back down the path to the device.
However, the parent hubs in the resumed path will not set their link
state change bit. Instead, the device that initiated the resume has to
send an asynchronous "Function Wake" Device Notification up to the host
controller. Therefore, we need a way to notify the USB core of a device
resume without going through the normal hub URB completion method.
First, make the xHCI roothub act like an external USB 3.0 hub and not
pass up the port link state change bit when a device-initiated resume
finishes. Introduce a new xHCI bit field, port_remote_wakeup, so that
we can tell the difference between a port coming out of the U3Exit state
(host-initiated resume) and the RExit state (ending state of
device-initiated resume).
Since the USB core can't tell whether a port on a hub has resumed by
looking at the Hub Status buffer, we need to introduce a bitfield,
wakeup_bits, that indicates which ports have resumed. When the xHCI
driver notices a port finishing a device-initiated resume, we call into
a new USB core function, usb_wakeup_notification(), that will set
the right bit in wakeup_bits, and kick khubd for that hub.
We also call usb_wakeup_notification() when the Function Wake Device
Notification is received by the xHCI driver. This covers the case where
the link between the roothub and the first-tier hub is in U0, and the
hub reflects the resume signaling back to the device without giving any
indication it has done so until the device sends the Function Wake
notification.
Change the code in khubd that handles the remote wakeup to look at the
state the USB core thinks the device is in, and handle the remote wakeup
if the port's wakeup bit is set.
This patch only takes care of the case where the device is attached
directly to the roothub, or the USB 3.0 hub that is attached to the root
hub is the device sending the Function Wake Device Notification (e.g.
because a new USB device was attached). The other cases will be covered
in a second patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Refactor the code to check for a remote wakeup on a port into its own
function. Keep the behavior the same, and set connect_change in
hub_events if the device disconnected on resume. Cleanup references to
hdev->children[i-1] to use a common variable.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 hubs have a different remote wakeup policy than USB 2.0 hubs.
USB 2.0 hubs, once they have remote wakeup enabled, will always send
remote wakes when anything changes on a port.
However, USB 3.0 hubs have a per-port remote wake up policy that is off
by default. The Set Feature remote wake mask can be changed for any
port, enabling remote wakeup for a connect, disconnect, or overcurrent
event, much like EHCI and xHCI host controller "wake on" port status
bits. The bits are cleared to zero on the initial hub power on, or
after the hub has been reset.
Without this patch, when a USB 3.0 hub gets suspended, it will not send
a remote wakeup on device connect or disconnect. This would show up to
the user as "dead ports" unless they ran lsusb -v (since newer versions
of lsusb use the sysfs files, rather than sending control transfers).
Change the hub driver's suspend method to enable remote wake up for
disconnect, connect, and overcurrent for all ports on the hub. Modify
the xHCI driver's roothub code to handle that request, and set the "wake
on" bits in the port status registers accordingly.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB 3.0 bus specification introduces a new type of power management
called function suspend. The idea is to be able to suspend different
functions (i.e. a scanner or an SD card reader on a USB printer)
independently. A device can be in U0, but have one or more functions
suspended. Thus, signaling a function resume with the standard device
remote wake signaling was not possible.
Instead, a device will (without prompt from the host) send a "device
notification" for the function remote wake. A new Set Feature Function
Remote Wake was developed to turn remote wake up on and off for each
function.
USB 3.0 devices can still go into device suspend (U3), and signal a
remote wakeup to bring the link back into U1. However, they now use the
function remote wake device notification to allow the host to know which
function woke the device from U3.
The spec is a bit ambiguous about whether a function is allowed to
signal a remote wakeup if the function has been enabled for remote
wakeup, but not placed in function suspend before the device is placed
into U3.
Section 9.2.5.1 says "Suspending a device with more than one function
effectively suspends all the functions within the device." I interpret
that to mean that putting a device in U3 suspends all functions, and
thus if the host has previously enabled remote wake for those functions,
it should be able to signal a remote wake up on port status changes.
However, hub vendors may have a different interpretation, and it can't
hurt to put the function into suspend before putting the device into U3.
I cannot get an answer out of the USB 3.0 spec architects about this
ambiguity, so I'm erring on the safe side and always suspending the
first function before placing the device in U3. Note, this code should
be fixed if we ever find any USB 3.0 devices that have more than one
function.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the USB 3.0 hub support went in, I disabled selective suspend for
all external USB 3.0 hubs because they used a different mechanism to
enable remote wakeup. In fact, other USB 3.0 devices that could signal
remote wakeup would have been prevented from going into suspend because
they would have stalled the SetFeature Device Remote Wakeup request.
This patch adds support for the USB 3.0 way of enabling remote wake up
(with a SetFeature Function Suspend request), and enables selective
suspend for all hubs during hub_probe. It assumes that all USB 3.0 have
only one "function" as defined by the interface association descriptor,
which is true of all the USB 3.0 devices I've seen so far. FIXME if
that turns out to change later.
After a device signals a remote wakeup, it is supposed to send a Device
Notification packet to the host controller, signaling which function
sent the remote wakeup. The host can then put any other functions back
into function suspend. Since we don't have support for function suspend
(and no devices currently support it), we'll just assume the hub
function will resume the device properly when it received the port
status change notification, and simply ignore any device notification
events from the xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xHCI roothubs go through slightly different port state machines when
either a device initiates a remote wakeup and signals resume, or when
the host initiates a resume.
According to section 4.19.1.2.13 of the xHCI 1.0 spec, on host-initiated
resume, the xHC port state machine automatically goes through the U3Exit
state into the U0 state, setting the port link state change (PLC) bit in
the process.
When a device initiates resume, the xHCI port state machine goes into
the "Resume" state and sets the PLC bit. Then the xHCI driver writes U0
into the port link state register to transition the port to U0 from the
Resume state.
We can't be sure the device is actually in the U0 state until we receive
the next port status change event with the PLC bit set. We really don't
want khubd to be polling the roothub port status bits until the device
is really in U0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Andiry Xu <andiry.xu@amd.com>
Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS. The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.
Actually, Linux also can work for MSI. This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe. It allows the xHCI driver
to try to enable MSI or MSI-X first. It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.
This patch should be backported to kernels as old as 2.6.32.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The current renesas_usbhs driver triggers
BUG: scheduling while atomic: ksoftirqd/0/3/0x00000102
with enabled CONFIG_DEBUG_ATOMIC_SLEEP, by submitting DMA transfers from
an atomic (tasklet) context, which is not supported by the shdma dmaengine
driver. Fix it by switching to a work.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
list.h already provide helpers to find the first entry and to move list
nodes to the tail of another list. This patch simply uses those helpers,
no functional changes.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this will get rid of a useless memcpy on
IRQ handling, thus improving driver performance.
Tested with OMAP5430 running g_mass_storage on
SuperSpeed and HighSpeed.
Note that we are removing the little endian access
of the TRB and all accesses will be in System endianness,
if there happens to be a system in BE, bit 12 of GSBUSCFG0
should be set so that HW does byte invariant BE accesses
when fetching TRBs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
[ balbi@ti.com: added a missing change on musb_gadget.c to avoid
a compile error on a later patch ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Li Yang <leoli@freescale.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introducing struct otg and collecting otg specific members
to it from struct usb_phy. There are no changes to
struct usb_phy at this stage. This also renames
transceiver specific functions, and offers aliases for the
old otg ones.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert all users.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is the first step in separating USB transceivers from
USB OTG utilities.
Includes fixes to IMX code from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code to set the device removable bits in the USB 2.0 roothub
descriptor was accidentally looking at the USB 3.0 port registers
instead of the USB 2.0 registers. This can cause an oops if there are
more USB 2.0 registers than USB 3.0 registers.
This should be backported to kernels as old as 2.6.39, that contain the
commit 4bbb0ace9a "xhci: Return a USB 3.0
hub descriptor for USB3 roothub."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Add a flag to tell wdm_read/wdm_write that a reset is in progress,
and wake any blocking read/write before taking the mutexes. This
allows the device to reset without waiting for blocking IO to
finish.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is done to resolve a merge conflict with:
drivers/usb/class/cdc-wdm.c
and to better handle future patches for this driver as it is under
active development at the moment.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_console in write paths for devices which can be used as a
console but do not use the generic write implementation.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_console in write path so that an error at least gets
reported once.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not report errors in write path if port is used as a console as this
may trigger the same error (and error report) resulting in a loop.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When host requests us to enter a test mode,
we cannot directly enter the test mode before
Status Phase is completed, otherwise the core
will never be able to deliver the Status ZLP
to host, because it has already entered the
requested Test Mode.
In order to fix the error, we move the actual
start of Test Mode right after we receive
Transfer Complete event of the status phase.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When implementing the USB2 testmode support via debugfs,
Felipe has committed a mistake when counting the number
of letters of some of the strings, resulting on an off
by one error which prevented some of the Test modes to
be entered properly.
This patch, fixes that mistake.
Signed-off-by: Gerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Hubs have a flag to indicate whether a given port carries removable devices
or not. This is not strictly accurate in that some built-in devices
will be flagged as removable, but followup patches will make use of platform
data to make this more reliable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace may want to make policy decisions based on whether or not a
given USB device is removable. Add a per-device member and support
for exposing it in sysfs. Information sources to populate it will be
added later.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This cuts down on the boilerplate code.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the handling of the 5v supply into badge4.c, removing this board
specific detail from the sa1111 ohci driver.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform hooks to be called when individual sa1111 devices are
enabled and disabled. This will allow us to move some platform
specifics out of the individual drivers.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a .owner initializer to the sa1111 driver structures to allow
allow the modules to be associated with their driver structures.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds SS descriptors to the ACM & generic serial gadget. The
ACM part was tested with minicom + dummy + send / receive files over
ttyACM <=> ttyGS0.
The generic serial part (f_serial) was not tested (haven't found a
driver on the host side).
The nokia & multi gadget use HS at most.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit 72c973dd aka ("usb: gadget: add usb_endpoint_descriptor to
struct usb_ep) the descriptor is part of the ep. Most gadgets like
g_zero or masstorage call config_ep_by_speed() to grab an available
endpoint which may be used for FS/HS/SS bulk/iso/intr and in a second
they assign the proper descriptor by calling config_ep_by_speed(). This
is good so far. A few of them like ncm call config_ep_by_speed() only if
ep->desc not assigned earlier. That means ep->desc is never assigned if
the endpoint was used by another gadget before it was removed.
Some of those gadgets also assign ep->driver_data to NULL on reset or
ep_disable part _but_ keep a reference to this endpoint. At ep_enable
time they assign driver_data to their private data. This probably needs
a clean up of its own.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Problem:
pch_udc continues operation even if VBUS becomes Low.
pch_udc performs D+ pulling up before VBUS becomes High.
USB device should be controlled according to VBUS state.
Root cause:
The current pch_udc is not always monitoring VBUS.
Solution:
The change of VBUS is detected using an interrupt of GPIO.
If VBUS became Low, pch_udc handles 'disconnect'.
After VBUS became High, a pull improves D+, and pch_udc
handles 'connect'.
[ balbi@ti.com : make it actually compile ]
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Problem:
In USB Suspend, pch_udc handles 'disconnect'.
Root cause:
The current pch_udc is not monitoring VBUS.
When USB cable is disconnected, USB Device Controller generates
an interrupt of USB Suspend.
pch_udc cannot distinguish it is USB Suspend or disconnect.
Therefore, pch_udc handles 'disconnect' after an interrupt of
USB Suspend happend.
Solution:
VBUS is detected through GPIO.
After an interrupt produced USB Suspend, if VBUS is Low,
pch_udc handles 'disconnect'.
If VBUS is High, pch_udc handles 'suspend'.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
_ep to ep is a pointer substraction so ep won't be zero unless _ep was
8. This was not intendent by the author, it was probably a typo while
checking for NULL of the argument.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the stream check fails then we leave ep->desc assigend but we return
with an error code. The caller assumes the endpoint is not enabled
(which is the case) but it can not enable it again due to this
assigment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that usb-storage has a target_alloc() routine, this patch (as1508)
moves some existing target-specific code out of the slave_alloc()
routine to where it really belongs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1507) adds a skip_vpd_pages flag to struct scsi_device
and a no_report_luns flag to struct scsi_target. The first is used to
control whether sd will look at VPD pages for information on block
provisioning, limits, and characteristics. The second prevents
scsi_report_lun_scan() from issuing a REPORT LUNS command.
The patch also modifies usb-storage to set the new flag bits for all
USB devices and targets, and to stop adjusting the scsi_level value.
Historically we have seen that USB mass-storage devices often don't
support VPD pages or REPORT LUNS properly. Until now we have avoided
these things by setting the scsi_level to SCSI_2 for all USB devices.
But this has the side effect of storing the LUN bits into the second
byte of each CDB, and now we have a report of a device which doesn't
like that. The best solution is to stop abusing scsi_level and
instead have separate flags for VPD pages and REPORT LUNS.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Perry Wagle <wagle@mac.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those transfer types are generally high bandwidth, so we
want to optimize transfers with those endpoints.
For that, databook suggests allocating 3 * wMaxPacketSize
of FIFO. Let's do that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
debugfs APIs will return NULL if it fails
to create the file/directory we ask it to
create.
Instead of checking for IS_ERR(ptr) we must
check for !ptr.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert our platform_data usage to OF property,
keep the legacy pdata for a while until the complete
conversion is done.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we set Run/Stop bit, we also move the
core to Rx.Detect state so that USB3 handshake
can start from a known location.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to dynamically re-size TxFifos for the
cases where default values will not do.
While at that, we create a simple function which,
for now, will just allocate one full packet fifo
space for each of the enabled endpoints.
This can be improved later in order to allow for
better throughput by allocating more space for
endpoints which could make good use of that like
isochronous and bulk.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass Storage gadget will take some time to handle
the SetConfiguration request, but even on those
cases we should move to CONFIGURED state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Only bit 3 of the event status bitfield is valid
and the others should not be considered.
Make sure SW matches documentation on that case
to avoid bogus debugging prints which would
confuse an engineer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is very useful for low level link testing where
we might not have a USB Host stack, only a scope to
verify signal integrity.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most link changes will, of course, happen with
the help of a matching host HW, but in some cases
we might want to debug very low level details about
the link and exposing this to debugfs sounds like
a good plan.
This is a preparation for such setup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is very useful for low level Link Testing where
we might not have a USB Host stack, only a scope to
verify signal integrity.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are some situations were we might need to
enable USB Test Modes without having access to a
Host stack. In such situations we cannot rely
solely on USB Control Messages to enable test
features.
For those cases, we will also allow test mode
to be enabled via debugfs and this patch is a
preparation for that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Following removal announce and addition to feature-removal-schedule.txt,
here is the actual source code deletion for Atmel CAP9 family.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
On mips, we got:
drivers/usb/musb/musb_io.h:44: error: conflicting types for 'readsl'
arch/mips/include/asm/io.h:529: error: previous definition of 'readsl' was here
drivers/usb/musb/musb_io.h:46: error: conflicting types for 'readsw'
arch/mips/include/asm/io.h:528: error: previous definition of 'readsw' was here
drivers/usb/musb/musb_io.h:48: error: conflicting types for 'readsb'
so, should add !defined(CONFIG_MIPS) too.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
People have complained that debugging code shouldn't alter the flow of
control; it should restrict itself to printing out warnings and error
messages. Bowing to popular opinion, this patch (as1518) changes the
debugging checks in usb_submit_urb() to follow this guideline.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Keith Packard <keithp@keithp.com>
CC: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
But before that we need to reorder the calls so that we don't need to
lower the reference counts if usb_autopm_get_interface fails.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just run into the following:
- new disk arrived in the system
- udev couldn't wait to get its hands on to to run ata_id /dev/sda
- this sent the cdb 0xa1 to the device.
- my UAS-gadget recevied the cdb and had no idea what to do with it. It
decided to send a status URB back with sense set to invalid opcode.
- the host side received it status and completed the scsi command.
- the host sent another scsi with 4kib data buffer
- Now I was confused why the data transfer is only 512 bytes instead of
4kib since the host is always allocating the complete transfer in one
go.
- Finally the system crashed while walking through the sg list.
This patch adds three new flags in order to distinguish between DATA
URB completed and outstanding. If we receive status before data, we
cancel data and let data complete the command.
This solves the problem for IN and OUT transfers but does not work for
BIDI.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The protocol specific structures and defines which are used by UAS are
moved into a header files by this patch so it can be accessed by the UAS
gadget as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The UAS driver requires SG support by the HCD operating the device. This
patch stops UAS from operating on a HCD without sg support and prints a
message to let him know.
The spec says:
|For [USB2] backward compatibility, the device shall present [BOT] as
|alternate interface zero (primary) and [UAS] as alternate interface one
|(secondary). A device which does not need backward compatibility with
|[BOT] shall present [UAS] as alternate interface zero. In [USB2]
|systems, the [BOT] driver or an associated filter driver may need to
|issue a SET INTERFACE request for alternate interface one and then allow
|the [UAS] driver to load.
If the user used usb_modeswitch to switch to UAS then he can go back to
BOT or use a different HCD. In case UAS is the only interface then there
is currently no way out.
In future usb_sg_wait() should be extended to provide a non-blocking
interface so it can work with the UAS driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=GTUe
-----END PGP SIGNATURE-----
Merge tag 'uas_for_sarah' of git://linutronix.de/users/bigeasy/linux into for-uas-next
Merge UAS bug fixes from Sebastian Andrzej Siewior, including some patches of
mine that he signed.
UAS fixes for Sarah
The Netlogic XLP SoC's on-chip USB controller appears as a PCI
USB device, but does not need the EHCI/OHCI handoff done in
usb/host/pci-quirks.c.
The pci-quirks.c is enabled for all vendors and devices, and is
enabled if USB and PCI are configured.
If we do not skip the qurik handling on XLP, the readb() call in
ehci_bios_handoff() will cause a crash since byte access is not
supported for EHCI registers in XLP.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when missing USB PHY clock, kernel booting up will halt during USB
initialization. We should check USBGP[PHY_CLK_VALID] bit to avoid
CPU hang in this case.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This otg driver depends on marvell EHCI driver, so add the dependence.
It can fix the following build error on i386:
ERROR: "usb_remove_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
ERROR: "usb_add_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distinguish Kconfig text by providing the Freescale family name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As ZTE have and will use more pid for new products this year,
so we need to add some new zte 3g-dongle's pid on option.c ,
and delete one pid 0x0154 because it use for mass-storage port.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've found that qcserial devices will not always wake up reliably
from autosuspend, so disable it.
Signed-off-by: Thomas Tuttle <ttuttle@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's really no point in doing all that
initcall trickery when we can safely let
udev handle module probing for us.
Remove all of that trickery, by moving everybody
to module_init() and making proper use of
platform_device_register() rather than
platform_device_probe().
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Tested-by: Tasslehoff Kjappfot <tasskjapp@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Nothing major, largest thing here is the removal of some drivers that
did not work at all. Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk8m8JEACgkQMUfUDdst+ymCFQCeNhTHopHy1PQbuCDwk8bSH4DW
1/YAn2k0YaaCrOo0HCzOslAVX18vGnWl
=TNNB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Here are a bunch of USB patches for 3.3-rc1.
Nothing major, largest thing here is the removal of some drivers that
did not work at all. Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (52 commits)
uwb & wusb: fix kconfig error
USB: Realtek cr: fix autopm scheduling while atomic
USB: ftdi_sio: Add more identifiers
xHCI: Cleanup isoc transfer ring when TD length mismatch found
usb: musb: omap2430: minor cleanups.
qcaux: add more Pantech UML190 and UML290 ports
Revert "drivers: usb: Fix dependency for USB_HWA_HCD"
usb: mv-otg - Fix build if CONFIG_USB is not set
USB: cdc-wdm: Avoid hanging on interface with no USB_CDC_DMM_TYPE
usb: add support for STA2X11 host driver
drivers: usb: Fix dependency for USB_HWA_HCD
kernel-doc: fix new warning in usb.h
USB: OHCI: fix new compiler warnings
usb: serial: kobil_sct: fix compile warning:
drivers/usb/host/ehci-fsl.c: add missing iounmap
USB: cdc-wdm: better allocate a buffer that is at least as big as we tell the USB core
USB: cdc-wdm: call wake_up_all to allow driver to shutdown on device removal
USB: cdc-wdm: use two mutexes to allow simultaneous read and write
USB: cdc-wdm: updating desc->length must be protected by spin_lock
USB: usbsevseg: fix max length
...
Add IAD to bind the two interfaces of ECM so that it works properly
in composite gadget mode.
Signed-off-by: Thirupathi <thirupathi.chippakurthy@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This otg driver depends on marvell EHCI driver, so add the dependence.
It can fix the following build error on i386:
ERROR: "usb_remove_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
ERROR: "usb_add_hcd" [drivers/usb/otg/mv_otg.ko] undefined!
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ab943a2e12 (USB: gadget: gadget zero uses new suspend/resume hooks)
introduced a copy-paste error where f_loopback.c writes to a variable
declared in f_sourcesink.c. This prevents one from creating gadgets
that only have a loopback function.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1514) cleans up some places where new_id and remove_id
sysfs attributes are created and deleted. Handling both attributes in
a single routine rather than a pair of routines makes the code
smaller. It also prevents certain kinds of errors, like one we
currently have in the USB subsystem: The removeid attribute is often
created even when newid isn't (because the driver's no_dynamid_id flag
is set).
In the case of the PCMCIA subsystem, the newid attribute is created
but never explicitly deleted. The patch adds a deletion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[v2: Editorial changes suggested by Sergei Shtylyov]
These modems use the Qualcomm MSM Interface (QMI) protocol for
management of their CDC ECM like wwan interface. This driver
is perfect for exporting the protocol to userspace.
The created character device will be indistinguishable from a
common AT command based Device Management interface, so
userspace applications must do some intelligent matching
on the USB device.
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix UWB/WUSB kconfig error by changing 'select' to 'depends on'.
drivers/usb/wusbcore/Kconfig:4:error: recursive dependency detected!
drivers/usb/wusbcore/Kconfig:4: symbol USB_WUSB is selected by USB_HWA_HCD
drivers/usb/host/Kconfig:559: symbol USB_HWA_HCD depends on UWB
drivers/uwb/Kconfig:5: symbol UWB is selected by USB_WUSB
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a TD length mismatch is found during isoc TRB enqueue, it directly
returns -EINVAL. However, isoc transfer is partially enqueued at this time,
and the ring should be cleared.
This should be backported to kernels as old as 2.6.36, which contain the
commit 522989a27c "xhci: Fix failed
enqueue in the middle of isoch TD."
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
* 'for-greg' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: musb: omap2430: minor cleanups.
usb: dwc3: unmap the proper number of sg entries
usb: musb: fix shutdown while usb gadget is in use
usb: gadget: f_mass_storage: Use "bool" instead of "int" in fsg_module_parameters
usb: gadget: check for streams only for SS udcs
usb: gadget: fsl_udc: fix the usage of udc->max_ep
drivers: usb: otg: Fix dependencies for some OTG drivers
usb: renesas: silence uninitialized variable report in usbhsg_recip_run_handle()
usb: gadget: SS Isoc endpoints use comp_desc->bMaxBurst too
usb: gadget: storage: endian fix
usb: dwc3: ep0: fix compile warning
usb: musb: davinci: fix build breakage
usb: gadget: langwell: don't call gadget's disconnect()
usb: gadget: langwell: drop langwell_otg support
usb: otg: kill langwell_otg driver
usb: dwc3: ep0: tidy up Pending Request handling
1/ remove incorrect comment (it is a non-blocking notifier)
2/ Use correct symbolic return value for notifier
3/ Make sure otg_notifier_work is cancelled before module exit.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As part of the removal of get_driver()/put_driver(), this patch
(as1511) changes all the places that add dynamic IDs for drivers.
Since these additions are done by writing to the drivers' sysfs
attribute files, and the attributes are removed when the drivers are
unregistered, there is no reason to take an extra reference to the
drivers.
The one exception is the pci-stub driver, which calls pci_add_dynid()
as part of its registration. But again, there's no reason to take an
extra reference here, because the driver can't be unloaded while it is
being registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
More ports we now know how to talk to.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 0dd2b62ada.
It causes a bunch of Kconfig errors:
drivers/usb/host/Kconfig:559:error: recursive dependency detected!
drivers/usb/host/Kconfig:559: symbol USB_HWA_HCD depends on UWB
drivers/uwb/Kconfig:5: symbol UWB is selected by USB_WUSB
drivers/usb/wusbcore/Kconfig:4: symbol USB_WUSB is selected by USB_HWA_HCD
showing that this really wasn't the correct fix at all.
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use ehci_setup() in ehci_ls1x_reset().
The Loongson1x SoCs have a built-in EHCI controller.
This patch adds the necessary glue code to make the generic EHCI
driver usable for them.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use INCR8 mode for system bus interface of the USB controller
on MPC512x. This is a work-around for the AHB bus lock up
problem observed on MPC512x when there is heavy simultaneous
PATA write or network (FEC) activity.
See also "12.4 The USB controller can issue transactions that lock
up the AHB bus under certain conditions" in MPC5121e (M36P) Errata.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.ue>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_register_dev() will change our .minor_base to 0 if
CONFIG_USB_DYNAMIC_MINORS is set. And it usually is, of
course.
Use dev_name() to print the proper interface name instead
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The probe does not strictly require the USB_CDC_DMM_TYPE
descriptor, which is a good thing as it makes the driver
usable on non-conforming interfaces. A user could e.g.
bind to it to a CDC ECM interface by using the new_id and
bind sysfs files. But this would fail with a 0 buffer length
due to the missing descriptor.
Fix by defining a reasonable fallback size: The minimum
device receive buffer size required by the CDC WMC standard,
revision 1.1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The probe does not strictly require the USB_CDC_DMM_TYPE
descriptor, which is a good thing as it makes the driver
usable on non-conforming interfaces. A user could e.g.
bind to it to a CDC ECM interface by using the new_id and
bind sysfs files. But this would fail with a 0 buffer length
due to the missing descriptor.
Fix by defining a reasonable fallback size: The minimum
device receive buffer size required by the CDC WMC standard,
revision 1.1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need bMaxPacketSize0, and keeping all these different size fields
around will only cause us to use the wrong one.
Seems the udev variable was only used for getting bMaxPacketSize0. We
could have used it for the usb_fill_*_urb() calls, but as it wasn't
before - why start now? Instead make the interface_to_usbdev()
calls consistent.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Documentation/usb/dma.txt states:
Most drivers should *NOT* be using these primitives; they don't need
to use this type of memory (dma-coherent), and memory returned from
kmalloc() will work just fine.
This driver handle only very low bandwith transfers. It is not an
obvious candidate for usb_alloc_coherent().
Using these calls only serves to complicate the code for no gain,
as has been shown by multiple bugs related to this allocation path.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As it turns out, there was a mismatch between the allocated inbuf size
(desc->bMaxPacketSize0, typically something like 64) and the length we
specified in the URB (desc->wMaxCommand, typically something like 2048)
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Filling the same URB with the exact same data is pointless. It can be filled
once and resubmitted. And not doing buffer allocation and URB filling at the
same place only serves to hide size mismatch bugs
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enable usb-storage support dynamic id again by using a fixed id entry
that describes a device using the Bulk-Only transport with the
Transparent SCSI protocol.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arnd Bergmann