Commit graph

56489 commits

Author SHA1 Message Date
Bartlomiej Zolnierkiewicz
4fce3164b8 pdc202xx_old: rewrite mode programming code (v2)
This patch is based on the documentation (I would like to thank Promise
for it) and also partially on the older vendor driver.

Rewrite mode programming code:

* disable 66MHz clock in pdc202xx_tune_chipset() so it is correctly disabled
  even if both devices on the channel are not DMA capable and after reset

* enable/disable IORDY and PREFETCH bits in pdc202xx_tune_chipset()
  as they need to be setup correctly also for PIO only devices, plus IORDY
  wasn't disabled for non-IORDY devices and PREFETCH wasn't disabled for
  ATAPI devices

* remove dead code for setting SYNC_ERDDY_EN bits from config_chipset_for_dma()
  (driver sets ->autotune to 1 so PIO modes are always programmed => lower
   nibble of register A never equals 4 => "chipset_is_set" is always true)

* enable PIO mode programming for all ATAPI devices
  (it was limited to ->media == ide_cdrom devices)

* remove extra reads of registers A/B/C, don't read register D et all

* do clearing / programming of registers A/B/C in one go
  (gets rid of extra PCI config space read/write cycle)

* set initial values of drive_conf/AP/BP/CP variables to zero
  (paranoia for the case when PCI reads fail)

* remove XFER_UDMA6 to XFER_UDMA5 remapping case - it can't happen
  (ide_rate_filter() takes care of it)

* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)

* fix bitmasks for clearing bits of register B:

  - when programming DMA mode bit 0x10 of register B was cleared which
    resulted in overclocked PIO timing setting (iff PIO0 was used)

  - when programming PIO mode bits 0x18 weren't cleared so suboptimal
    timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
    and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)

* add FIXME comment about missing locking for 66MHz clock register

Also while at it:

* remove unused defines

* do a few cosmetic / CodingStyle fixes

* bump driver version

v2:
* in pdc202xx_tune_chipset() the old content of drive configuration
  registers is used only by the debugging code so cover "drive_conf"
  PCI registers read by #if PDC202XX_DEBUG_DRIVE_INFO
  (Noticed by Sergei Shtylyov)

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:41 +02:00
Kim Phillips
4e19b5c193 ucc_geth: eliminate max-speed, change interface-type to phy-connection-type
It was agreed that phy-connection-type was a better name for
the interface-type property, so this patch renames it.

Also, the max-speed property name was determined too generic,
and is therefore eliminated in favour of phy-connection-type
derivation logic.

includes corrections to copyright text.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-15 17:44:40 -04:00
Vitaly Wool
f2773a2959 smc911x: fix compilation breakage
Looks like the new version of this patch has been overlooked,
so I'm resending it.

It just adapts the driver to the new IRQ API
according to what Russell has pointed out.

 drivers/net/smc911x.c |    6 ++----
 1 files changed, 2 insertions(+), 4 deletions(-)

Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-15 17:44:39 -04:00
olof@lixom.net
1af7f05628 pasemi_mac: Fix local-mac-address parsing
Turns out we have an old version of firmware that stores the mac address
in 'mac-address' as a string instead of a byte array. All versions that
use local-mac-address should have it as byte array, so no need to do
string parsing for that case.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-15 17:44:39 -04:00
olof@lixom.net
fd17825480 pasemi_mac: Terminate PCI ID list
This caused some very interesting behaviour depending on what happened to
be built at the same time. Add terminating empty entry to the list of IDs.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-15 17:44:39 -04:00
Olof Johansson
52a9435183 pasemi_mac: Interrupt ack fixes
Interrupt ack fixes

Fix the packet count resets at interrupt time, using the cacheable
packet count status to set number of processed/received packets, since
the ack count is the cumulative number of packets processed, and not
incremental.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-15 17:44:39 -04:00
olof@lixom.net
a54c545134 pasemi_mac: Fix register defines
Some shift values were obviously wrong. Fix them to correspond with
the masks.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-15 17:44:39 -04:00
Linus Torvalds
0560551dca Merge master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
  [AGPGART] Fix wrong ID in via-agp.c
2007-05-15 12:10:26 -07:00
Linus Torvalds
1ca9bc4f2a Merge master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Correct revision mask for powernow-k8
  [CPUFREQ] powernow-k7: fix MHz rounding issue with perflib
  [CPUFREQ] Support rev H AMD64s in powernow-k8
2007-05-15 12:10:00 -07:00
Jens Axboe
f653c34dd3 ll_rw_blk: fix gcc 4.2 warning on current_io_context()
current_io_context() is both static and exported with EXPORT_SYMBOL().
As there are no users outside of ll_rw_blk.c itself, just kill the
export.

Problem reported by Martin Michlmayr <tbm@cyrius.com>

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 10:44:15 -07:00
Linus Torvalds
de7860c3f3 Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB/cm: Optimize stale connection detection
  IB/mthca: Set cleaned CQEs back to HW ownership when cleaning CQ
  IB/mthca: Fix posting >255 recv WRs for Tavor
  RDMA/cma: Add check to validate that cm_id is bound to a device
  RDMA/cma: Fix synchronization with device removal in cma_iw_handler
  RDMA/cma: Simplify device removal handling code
  IB/ehca: Disable scaling code by default, bump version number
  IB/ehca: Beautify sysfs attribute code and fix compiler warnings
  IB/ehca: Remove _irqsave, move #ifdef
  IB/ehca: Fix AQP0/1 QP number
  IB/ehca: Correctly set GRH mask bit in ehca_modify_qp()
  IB/ehca: Serialize hypervisor calls in ehca_register_mr()
  IB/ipath: Shadow the gpio_mask register
  IB/mlx4: Fix uninitialized spinlock for 32-bit archs
  mlx4_core: Remove unused doorbell_lock
  net: Trivial MLX4_DEBUG dependency fix.
2007-05-15 09:52:31 -07:00
Christoph Lameter
cfbf07f2a8 SLUB: CONFIG_LARGE_ALLOCS must consider MAX_ORDER limit
Take MAX_ORDER into consideration when determining KMALLOC_SHIFT_HIGH.
Otherwise we may run into a situation where we attempt to create general
slabs larger than MAX_ORDER.

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:01 -07:00
Jeremy Fitzhardinge
6a3ee3d552 i386: fix voyager build
This adds an smp_ops for voyager, and hooks things up appropriately.  This is
the first baby-step to making subarch runtime switchable.

Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:01 -07:00
Jeremy Fitzhardinge
297d9c035e i386: move common parts of smp into their own file
Several parts of kernel/smp.c and smpboot.c are generally useful for other
subarchitectures and paravirt_ops implementations, so make them available for
reuse.

Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Prarit Bhargava
838c41184f Remove cpu hotplug defines for __INIT & __INITDATA
After examining what was checked in and the code base I discovered that most
of 86c0baf123 wasn't necessary anymore....

So here's a patch that reverts the last part of that changeset:

Revert part of 86c0baf123.

The kernel has moved forward to a state where the original change is not
necessary.  After porting forward, this final version of the patch was
applied and broke non-x86 architectures.

Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Stephen Rothwell
3bd2aad210 Revert "MAINTAINERS: remove invalid list address for TPM"
This reverts commit b6d1c9a447.

Others tell me that this address has worked for them, so I can only
assume that I hit a glitch in the sourceforge mail system.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Kylene Hall <kjhall@us.ibm.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Thomas Gleixner
8f89441b37 clocksource: fix lock order in the resume path
lockdep complains about the lock nesting of clocksource and watchdog lock
in the resume path.

Change the resume marker to a bit operation and remove the lock from this
path.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Geert Uytterhoeven
3c46bdcaec m68k: implement __clear_user()
m68k: implement __clear_user(), which is needed by fs/signalfd.c

Since we always let the MMU do all checking, clear_user() and __clear_user()
are identical. The old clear_user() is renamed to __clear_user() for
consistency.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Simon Horman
0fcdf96ca9 alpha: fix hard_smp_processor_id compile error
"Remove hardcoding of hard_smp_processor_id on UP systems",
2f4dfe206a in Linus' tree, moved
the definition of hard_smp_processor_id linux/smp.h to asm/smp.h
for UP systems. This causes a regression on Alpha.

cc1: warnings being treated as errors
arch/alpha/kernel/setup.c: In function 'setup_arch':
arch/alpha/kernel/setup.c:506: warning: implicit declaration of function 'hard_smp_processor_id'
make[1]: *** [arch/alpha/kernel/setup.o] error 1
make: *** [arch/alpha/kernel] error 2

By including asm/smp.h non-conditionally in asm/mmu_context.h
the problem appears to be resolved.

Cc: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Yoshinori Sato
b67405bbbb h8300 atomic.h update
add atomic_sub_and_test define.

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Paul Mundt
218f0aaee8 nommu: add ioremap_page_range()
lib/ioremap.c is presently only built in if CONFIG_MMU is set.  While this
is reasonable, platforms that support both CONFIG_MMU=y or n need to be
able to call in to this regardless.

As none of the current nommu platforms do anything special with ioremap(),
we assume that it's always successful.

This fixes the SH-4 build with CONFIG_MMU=n.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Davide Libenzi
f0ee9aabb0 epoll: move kfree inside ep_free
Move the kfree() call inside the ep_free() function.

Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Davide Libenzi
67647d0fb8 epoll: fix some comments
Fixes some epoll code comments.

Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:54:00 -07:00
Davide Libenzi
c7ea763025 epoll locks changes and cleanups
Changes the rwlock to a spinlock, and drops the use-count variable.
Operations are always bound by the mutex now, so the use-count is no more
needed.  For the same reason, the rwlock can become a simple spinlock.

Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:53:59 -07:00
Davide Libenzi
d47de16c72 fix epoll single pass code and add wait-exclusive flag
Fixes the epoll single pass code.  During the unlocked event delivery (to
userspace) code, the poll callback can re-issue new events, and we must
receive them correctly.  Since we loop in a lockless fashion, we want to be
O(nready), and we don't want to flash on/off the spinlock for every event, we
have the poll callback to use a secondary list to queue events while we're
inside the event delivery loop.  The rw_semaphore has been turned into a
mutex.  This patch also adds the wait-exclusive flag, as suggested by Davi
Arnaut.

Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 08:53:59 -07:00
Dave Jones
99fbe1ac21 [CPUFREQ] Correct revision mask for powernow-k8
Mark Langsdorf points out that the correct define for this
revision bump is 0x80000.  Also to save us having to keep
renaming the #define, give it a more meaningful name.

Signed-off-by: Dave Jones <davej@redhat.com>
2007-05-14 18:27:29 -04:00
Linus Torvalds
faa8b6c3c2 Revert "ipmi: add new IPMI nmi watchdog handling"
This reverts commit f64da958df.

Andi Kleen is unhappy with the changes, and they really do not seem
worth it.  IPMI could use DIE_NMI_IPI instead of the new callback, even
though that ends up having its own set of problems too, mainly because
the IPMI code cannot really know the NMI was from IPMI or not.

Manually fix up conflicts in arch/x86_64/kernel/traps.c and
drivers/char/ipmi/ipmi_watchdog.c.

Cc: Andi Kleen <ak@suse.de>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Corey Minyard <minyard@acm.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-14 15:24:24 -07:00
Michael S. Tsirkin
7c5b9ef857 IPoIB/cm: Optimize stale connection detection
In the presence of some running RX connections, we repeat
queue_delayed_work calls each 4 RX WRs, which is a waste.  It's enough
to start stale task when a first passive connection is added, and
rerun it every IPOIB_CM_RX_DELAY as long as there are outstanding
passive connections.

This removes some code from RX data path.

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 14:11:01 -07:00
Michael S. Tsirkin
bd18c11277 IB/mthca: Set cleaned CQEs back to HW ownership when cleaning CQ
mthca_cq_clean() updates the CQ consumer index without moving CQEs
back to HW ownership.  As a result, the same WRID might get reported
twice, resulting in a use-after-free.  This was observed in IPoIB CM.
Fix by moving all freed CQEs to HW ownership.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=617>

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 14:10:34 -07:00
Michael S. Tsirkin
3e28c56b9b IB/mthca: Fix posting >255 recv WRs for Tavor
Fix posting lists of > 255 receive WRs for Tavor: rq.next_ind must
be updated each doorbell, otherwise the next doorbell will use an
incorrect index.

Found by Ronni Zimmermann at Mellanox.

Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 14:10:34 -07:00
Sean Hefty
6c719f5c6c RDMA/cma: Add check to validate that cm_id is bound to a device
Several checks in the rdma_cm check against the state of the
cm_id, but only to validate that the cm_id is bound to an underlying
transport specific CM and an RDMA device.  Make the check explicit
in what we're trying to check for, since we're not synchronizing
against the cm_id state.

This will allow a user to disconnect a cm_id or reject a connection
after receiving a device removal event.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 14:10:32 -07:00
Sean Hefty
be65f086f2 RDMA/cma: Fix synchronization with device removal in cma_iw_handler
The cma_iw_handler needs to validate the state of the rdma_cm_id before
processing a new connection request to ensure that a device removal is
not already being processed for the same rdma_cm_id.  Without the state
check, the user can receive simultaneous callbacks for the same cm_id, or
a callback after they've destroyed the cm_id.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:56:32 -07:00
Sean Hefty
8aa08602bd RDMA/cma: Simplify device removal handling code
Add a new routine and rename another to encapsulate common code for
synchronizing with device removal.

Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:54:49 -07:00
Joachim Fenkes
4e430dcb7b IB/ehca: Disable scaling code by default, bump version number
- Scaling code is still considered experimental, so disable it by default
- Increase version to SVNEHCA_0023

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:41:40 -07:00
Joachim Fenkes
bba9b6013e IB/ehca: Beautify sysfs attribute code and fix compiler warnings
eHCA's sysfs attributes are now being created via sysfs_create_group(),
making the process neatly table-driven. The return value is checked, thus
fixing a few compiler warnings.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:40:45 -07:00
Joachim Fenkes
c7a14939e7 IB/ehca: Remove _irqsave, move #ifdef
- In ehca_process_eq(), we're IRQ safe throughout the whole function, so we
  don't need another _irqsave in the middle of flight.

- take_over_work() is only called by comp_pool_callback(), so it can move
  into the same #ifdef block.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:40:05 -07:00
Hoang-Nam Nguyen
c55a0ddd8e IB/ehca: Fix AQP0/1 QP number
AQP0/1 should report qp_num={0|1} and the actual QP# should be stored
in struct ehca_qp, not the other way round.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:39:31 -07:00
Joachim Fenkes
92761cdaf2 IB/ehca: Correctly set GRH mask bit in ehca_modify_qp()
The driver needs to always supply the "GRH present" flag to the
hypervisor, whether it's true or false. Not supplying it (i.e. not
setting the corresponding mask bit) amounts to a "perhaps", which we
don't want.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:38:57 -07:00
Stefan Roscher
5d88278e3b IB/ehca: Serialize hypervisor calls in ehca_register_mr()
Some pSeries hypervisor versions show a race condition in the allocate
MR hCall.  Serialize this call per adapter to circumvent this problem.

Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:38:11 -07:00
Arthur Jones
8f140b407f IB/ipath: Shadow the gpio_mask register
Once upon a time, GPIO interrupts were rare.  But then a chip bug in
the waldo series forced the use of a GPIO interrupt to signal packet
reception.  This greatly increased the frequency of GPIO interrupts
which have the gpio_mask bits set on the waldo chips.  Other bits in
the gpio_status register are used for I2C clock and data lines, these
bits are usually on.  An "unlikely" annotation leftover from the old
days was improperly applied to these bits, and an unnecessary chip
mmio read was being accessed in the interrupt fast path on waldo.

Remove the stagnant unlikely annotation in the interrupt handler and
keep a shadow copy of the gpio_mask register to avoid the slow mmio
read when testing for interruptable GPIO bits.

Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:22:42 -07:00
Jack Morgenstein
26c6bc7b81 IB/mlx4: Fix uninitialized spinlock for 32-bit archs
uar_lock spinlock was used in mlx4_ib_cq_arm without being initialized
(this only affects 32-bit archs, because uar_lock is not used on
64-bit archs and MLX4_INIT_DOORBELL_LOCK() is a NOP).

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-14 13:02:58 -07:00
Linus Torvalds
3ec2ab5514 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  pxamci: fix PXA27x MMC workaround for bad CRC with 136 bit response
  mmc: use assigned major for block device
  sdhci: handle dma boundary interrupts
  mmc: au1xmmc command types check from data flags
2007-05-14 12:29:14 -07:00
Linus Torvalds
200cfbb36c Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV4] SNMP: Display new statistics at /proc/net/netstat
  [IPV6]: Reverse sense of promisc tests in ip6_mc_input
  [NET_SCHED]: prio qdisc boundary condition
  [IPSEC]: Don't warn if high-order hash resize fails
  [IPSEC]: Check validity of direction in xfrm_policy_byid
2007-05-14 12:28:11 -07:00
Linus Torvalds
29e0937bb6 Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Update defconfig.
  [VIDEO]: XVR-500 and XVR-2500 need FB=y.
  [SPARC32]: asm/system.h needs asm/smp.h
  [SPARC32]: Update defconfig.
  [SPARC32]: Fix sparc32 kdebug changes.
  [SPARC64]: Accept ebus_bus_type for generic DMA ops.
  [SPARC64]: Add missing cpus_empty() check in hypervisor xcall handling.
  [SCSI]: Add help text for SCSI_ESP_CORE.
  [SPARC] SBUS: display7seg.c needs asm/io.h
  [SPARC] SBUS: bbc_i2c.c needs asm/io.h
  [SPARC64]: Be more resiliant with PCI I/O space regs.
  [SERIAL] SUNHV: Add an ID string.
2007-05-14 12:27:17 -07:00
Stephen Rothwell
140ff8b045 Declare another couple of compat syscalls.
compat_sys_signalfd and compat_sys_timerfd need declarations before
PowerPC can wire them up.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-14 12:16:01 -07:00
Dave Jones
a34be83a9c MAINTAINERS update.
I've not really 'maintained' this code for years, and others
are doing a much more thorough job these days.
Removing myself might stem some of the crazier emails I get.

Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-14 12:14:26 -07:00
Thomas Gleixner
d10ff3fb62 timekeeping fix patch got mis-applied
The time keeping code move to kernel/time/timekeeping.c broke the
clocksource resume logic patch, which got applied to the old file by a
fuzzy application.  Fix it up and move the clocksource_resume() call to
the appropriate place.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ tssk, tssk, everybody should use --fuzz=0 ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-14 12:13:11 -07:00
Nicolas Pitre
90e07d9f54 pxamci: fix PXA27x MMC workaround for bad CRC with 136 bit response
... and make it depend on the response flag instead of the command type.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-14 18:51:48 +02:00
Pierre Ossman
fe6b4c8840 mmc: use assigned major for block device
The MMC block devices now have an assigned major. Make sure
we actually use it.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-14 18:51:43 +02:00
Pierre Ossman
6ba736a10e sdhci: handle dma boundary interrupts
When the device hits certain memory boundaries, it signals an
interrupt and expects to be serviced. We don't need the feature
but we need to make sure the device doesn't stall.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-14 18:51:37 +02:00