When runtime_pm was originally added, it was done in rather confusing
way: omap2430_musb_init() (called from musb_init_controller) would do
runtime_pm_get_sync() and musb_init_controller() itself would do
runtime_pm_put to balance it out. This is not only confusing but also
wrong if non-omap2430 glue layer is used.
This confusion resulted in commit 772aed45b6 "usb: musb: fix
pm_runtime mismatch", that removed runtime_pm_put() from
musb_init_controller as that looked unbalanced, and also happened to
fix unrelated isp1704_charger crash. However this broke runtime PM
functionality (musb is now always powered, even without gadget active).
Avoid these confusing runtime pm dependences by making
musb_init_controller() and omap2430_musb_init() do their own runtime
get/put pairs; also cover error paths. Remove unneeded runtime_pm_put
in omap2430_remove too. isp1704_charger crash that motivated
772aed45b6 will be fixed by following patch.
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This change prevents runtime suspend and resume actual execution, if
omap2430 controller driver is loaded after musb-hdrc, and therefore the
controller isn't initialized properly.
The problem is reproducible with 3.1.y and 3.2 kernels.
Kernel configuration of musb:
% cat .config | egrep 'MUSB|GADGET'
CONFIG_USB_MUSB_HDRC=y
# CONFIG_USB_MUSB_TUSB6010 is not set
CONFIG_USB_MUSB_OMAP2PLUS=m
# CONFIG_USB_MUSB_AM35X is not set
CONFIG_MUSB_PIO_ONLY=y
CONFIG_USB_GADGET=y
# CONFIG_USB_GADGET_DEBUG is not set
# CONFIG_USB_GADGET_DEBUG_FILES is not set
# CONFIG_USB_GADGET_DEBUG_FS is not set
CONFIG_USB_GADGET_VBUS_DRAW=2
CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS=2
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_GADGET_DUALSPEED=y
CONFIG_USB_GADGETFS=m
# CONFIG_USB_MIDI_GADGET is not set
Fixes the following oops on module unloading:
Unable to handle kernel NULL pointer dereference at virtual address 00000220
----8<----
[<bf162088>] (omap2430_runtime_resume+0x24/0x54 [omap2430]) from [<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50)
[<c0302e34>] (pm_generic_runtime_resume+0x3c/0x50) from [<c0031a24>] (_od_runtime_resume+0x28/0x2c)
[<c0031a24>] (_od_runtime_resume+0x28/0x2c) from [<c0306cb0>] (__rpm_callback+0x60/0xa0)
[<c0306cb0>] (__rpm_callback+0x60/0xa0) from [<c0307f2c>] (rpm_resume+0x3fc/0x6e4)
[<c0307f2c>] (rpm_resume+0x3fc/0x6e4) from [<c030851c>] (__pm_runtime_resume+0x5c/0x90)
[<c030851c>] (__pm_runtime_resume+0x5c/0x90) from [<c02fd0dc>] (__device_release_driver+0x2c/0xd0)
[<c02fd0dc>] (__device_release_driver+0x2c/0xd0) from [<c02fda18>] (driver_detach+0xe8/0xf4)
[<c02fda18>] (driver_detach+0xe8/0xf4) from [<c02fcf88>] (bus_remove_driver+0xa0/0x104)
[<c02fcf88>] (bus_remove_driver+0xa0/0x104) from [<c02fde54>] (driver_unregister+0x60/0x80)
[<c02fde54>] (driver_unregister+0x60/0x80) from [<c02ff2d4>] (platform_driver_unregister+0x1c/0x20)
[<c02ff2d4>] (platform_driver_unregister+0x1c/0x20) from [<bf162928>] (omap2430_exit+0x14/0x1c [omap2430])
[<bf162928>] (omap2430_exit+0x14/0x1c [omap2430]) from [<c007d8bc>] (sys_delete_module+0x1f4/0x264)
[<c007d8bc>] (sys_delete_module+0x1f4/0x264) from [<c000f000>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@nokia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # 3.1
Signed-off-by: Felipe Balbi <balbi@ti.com>
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WiB6
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: transceiver changes for 3.4
Here we have a big rework done by Heikki Krogerus (thanks) which
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
a patch making modules behave better, there's a fix on debugfs'
error path, a small change removing an unnecessary pm_runtime
call on musb_shutdown() and a fix to relesect the endpoint in
Interrupt context.
This last patch is needed because we must drop musb's lock when
calling request->complete() and that could cause problems if another
thread queues a request and ends up changing MUSB_INDEX register.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2VXE
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: MUSB changes for 3.4
Here are a set of changes to the MUSB driver. In summary we have
a patch making modules behave better, there's a fix on debugfs'
error path, a small change removing an unnecessary pm_runtime
call on musb_shutdown() and a fix to relesect the endpoint in
Interrupt context.
This last patch is needed because we must drop musb's lock when
calling request->complete() and that could cause problems if another
thread queues a request and ends up changing MUSB_INDEX register.
This changes the otg functions so that they receive struct
otg instead of struct usb_phy as parameter and
converts all users of these functions to pass the otg member
of their usb_phy.
Includes fixes to IMX code from Sascha Hauer.
[ balbi@ti.com : fixed a compile warning on ehci-mv.c ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.
Includes fixes from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
[ balbi@ti.com: added a missing change on musb_gadget.c to avoid
a compile error on a later patch ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's really no point in doing all that
initcall trickery when we can safely let
udev handle module probing for us.
Remove all of that trickery, by moving everybody
to module_init() and making proper use of
platform_device_register() rather than
platform_device_probe().
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Tested-by: Tasslehoff Kjappfot <tasskjapp@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1/ remove incorrect comment (it is a non-blocking notifier)
2/ Use correct symbolic return value for notifier
3/ Make sure otg_notifier_work is cancelled before module exit.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These are handled by drivers core, and in a way that doesn't wake up the
devices.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
enabled && driver || !enabled can be simplified to !enabled || driver.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
fix the following compile warning:
drivers/usb/musb/omap2430.c: In function 'musb_otg_notifier_work':
drivers/usb/musb/omap2430.c:279:3: warning: 'return' with a value, in
function returning void
drivers/usb/musb/omap2430.c:282:2: warning: 'return' with a value, in
function returning void
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb pm_runtime_get_sync call happens in intrrupt context on cable attach case
That can result in re-enabling the interrupts and cause side affects.
So move the code to a work queue.
Following is the error path hit on cable attach:
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:802
in_atomic(): 0, irqs_disabled(): 0, pid: 18, name: irq/378-twl6030
Backtrace:
[<c00520f0>] (dump_backtrace+0x0/0x110) from [<c054f454>] (dump_stack+0x18/0x1c)
[<c054f43c>] (dump_stack+0x0/0x1c) from [<c007f59c>] (__might_sleep+0x130/0x134)
[<c007f46c>] (__might_sleep+0x0/0x134) from [<c02c2794>] (__pm_runtime_resume+0x94/0x98)
[<c02c2700>] (__pm_runtime_resume+0x0/0x98) from [<c033e7e4>] (musb_otg_notifications+0x9c/0x164)
[<c033e748>] (musb_otg_notifications+0x0/0x164) from [<c00b3df0>] (notifier_call_chain+0x4c/0x8c)
[<c00b3da4>] (notifier_call_chain+0x0/0x8c) from [<c00b44a8>] (__atomic_notifier_call_chain+0x40/0x54)
[<c00b4468>] (__atomic_notifier_call_chain+0x0/0x54) from [<c00b44dc>] (atomic_notifier_call_chain+0x20/0x28)
[<c00b44bc>] (atomic_notifier_call_chain+0x0/0x28) from [<c033f124>] (twl6030_usb_irq+0xc8/0xdc)
[<c033f05c>] (twl6030_usb_irq+0x0/0xdc) from [<c00d79f8>] (irq_thread_fn+0x24/0x40)
[<c00d79d4>] (irq_thread_fn+0x0/0x40) from [<c00d7b64>] (irq_thread+0x150/0x1d8)
[<c00d7a14>] (irq_thread+0x0/0x1d8) from [<c00adf70>] (kthread+0x94/0x98)
[<c00adedc>] (kthread+0x0/0x98) from [<c0094388>] (do_exit+0x0/0x720)
Tested with:
MUSB Device mode: Cold boot / Hot plug
MUSB Host mode: Cold boot / Hot plug
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we need to save and restore OTG_INTERFSEL register
else we will be unable to function on resume after
OFF mode.
Reported-by: Devaraj Rangasamy <dev@ti.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.
This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have a generic way of enabling/disabling
different debug messages on a driver called
DYNAMIC_PRINTK. Anyone interested in enabling
just part of the debug messages, please read
the documentation under:
Documentation/dynamic-debug-howto.txt
for information on how to use that great
infrastructure.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.
Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent runtime pm and hwmod conversions for 2.6.39 broke the musb peripheral
mode OMAP retention idle on boards where the board mode in struct
musb_hdrc_platform_data is set to MUSB_PERIPHERAL.
These conversions changed the way how the OTG_SYSCONFIG register is
configured and used in runtime. Before 2.6.39 smart standby/idle modes were
activated statically in OTG_SYSCONFIG. Those modes allow that the musb is
able to idle when peripheral device is not connected to host.
In 2.6.39 the OTG_SYSCONFIG is updated runtime depending on VBUS status.
No standby/idle modes are used when device is connected and force
standby/idle when disconnected.
Unfortunately VBUS disconnect event that handles the disconnect case lets
the peripheral musb to idle only when board mode is MUSB_OTG. Fix this by
checking the peripheral mode also.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix build failure introduced by commit
7acc6197b7 (usb: musb: Idle path retention
and offmode support for OMAP3) when building without gadget
support.
CC drivers/usb/musb/omap2430.o
drivers/usb/musb/omap2430.c: In function ‘musb_otg_notifications’:
drivers/usb/musb/omap2430.c:262: error: ‘struct musb’ has no member named ‘gadget_driver’
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (172 commits)
USB: Add support for SuperSpeed isoc endpoints
xhci: Clean up cycle bit math used during stalls.
xhci: Fix cycle bit calculation during stall handling.
xhci: Update internal dequeue pointers after stalls.
USB: Disable auto-suspend for USB 3.0 hubs.
USB: Remove bogus USB_PORT_STAT_SUPER_SPEED symbol.
xhci: Return canceled URBs immediately when host is halted.
xhci: Fixes for suspend/resume of shared HCDs.
xhci: Fix re-init on power loss after resume.
xhci: Make roothub functions deal with device removal.
xhci: Limit roothub ports to 15 USB3 & 31 USB2 ports.
xhci: Return a USB 3.0 hub descriptor for USB3 roothub.
xhci: Register second xHCI roothub.
xhci: Change xhci_find_slot_id_by_port() API.
xhci: Refactor bus suspend state into a struct.
xhci: Index with a port array instead of PORTSC addresses.
USB: Set usb_hcd->state and flags for shared roothubs.
usb: Make core allocate resources per PCI-device.
usb: Store bus type in usb_hcd, not in driver flags.
usb: Change usb_hcd->bandwidth_mutex to a pointer.
...
In OMAP3xxx with OTG mode or host only mode, When the device
is inserted after the gadget driver loading the enumeration was not
through. This is because the mentor controller will start sensing the
ID PIN only after setting the session bit.
So after ID-GND, need to set the session bit for mentor to get it
configured as A device.
This is a fix to set the session bit again in ID_GND notification handler.
Tested with OMAP3630Zoom3 platform.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch supports the retention and offmode support in the idle path for
musb driver using runtime pm APIs.
This is restricted to support offmode and retention only when device not
connected.When device/cable connected with gadget driver loaded,configured
to no idle/standby which will not allow the core transition to retention
or off.
There is no context save/restore done by hardware for musb in OMAP3
and OMAP4,driver has to take care of saving and restoring the context
during offmode.
Musb has a requirement of configuring sysconfig register to force
idle/standby mode and set the ENFORCE bit in module STANDBY register
for retention and offmode support.
Runtime pm and hwmod frameworks will take care of configuring to force
idle/standby when pm_runtime_put_sync is called and back to no
idle/standby when pm_runeime_get_sync is called.
Compile, boot tested and also tested the retention in the idle path on
OMAP3630Zoom3. And tested the global suspend/resume with offmode enabled.
Usb basic functionality tested on OMAP4430SDP.
There is some problem with idle path offmode in mainline, I could not test
with offmode. But I have tested this patch with resetting the controller
in the idle path when wakeup from retention just to make sure that the
context is lost, and restore path is working fine.
Removed .suspend/.resume fnction pointers and functions because there
is no need of having these functions as all required work is done
at runtime in the driver.
There is no need to call the runtime pm api with glue driver device
as glue layer device is the parent of musb core device, when runtime apis
are called for the child, parent device runtime functionality
will be invoked.
Design overview:
pm_runtime_get_sync: When called with musb core device takes care of
enabling the clock, calling runtime callback function of omap2430 glue
layer, runtime call back of musb driver and configure the musb sysconfig
to no idle/standby
pm_runtime_put: Takes care of calling runtime callback function of omap2430
glue layer, runtime call back of musb driver, Configure the musb sysconfig
to force idle/standby and disable the clock.
During musb driver load: Call pm_runtime_get_sync.
End of musb driver load: Call pm_runtime_put
During gadget driver load: Call pm_runtime_get_sync,
End of gadget driver load: Call pm_runtime_put if there is no device
or cable is connected.
During unload of the gadget driver:Call pm_runtime_get_sync if cable/device
is not connected.
End of the gadget driver unload : pm_runtime_put
During unload of musb driver : Call pm_runtime_get_sync
End of unload: Call pm_runtime_put
On connect of usb cable/device -> transceiver notification(VBUS and ID-GND):
pm_runtime_get_sync only if the gadget driver loaded.
On disconnect of the cable/device -> Disconnect Notification:
pm_runtime_put if the gadget driver is loaded.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For OMAP3 and OMAP4 for offmode and retention support, musb
sysconfig is configured to force idle and standby with ENABLE_FORCE bit
of OTG_FORCESTNDBY set.
And on wakeup configure to no ilde/standby with resetting the ENABLE_FORCE
bit. There is not need to save and restore of this register anymore
so removed omap2430_save_context/omap2430_restore_context functions.
and also removed otg_forcestandby member of musb_context_registers
structure
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
OMAP4430 is embedded with UTMI PHY. This PHY does not support the
OTG features like ID pin detection and VBUS detection. This function
is exported to an external companion chip TWL6030. Software must retrieve
the OTG HNP and SRP status from the TWL6030 and configure the bits inside
the control module that drive the related USBOTGHS UTMI interface signals.
It must also read back the UTMI signals needed to configure the TWL6030
OTG module.
Can find more details in the TRM[1].
[1]:http://focus.ti.com/pdfs/wtbu/OMAP4430_ES2.0_Public_TRM_vJ.pdf
In OMAP4430 musb driver VBUS and ID notifications are received from the
transceiver driver. If the cable/device is connected during boot,
notifications from transceiver driver will be missed till musb driver
is loaded.
Patch to configure the transceiver in the platform_enable/disable
functions and enable the vbus in the gadget driver based on the
last_event of the otg_transceiver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Calling runtime pm APIs pm_runtime_put_sync() and pm_runtime_get_sync()
for enabling/disabling the clocks, sysconfig settings.
Enable clock, configure no-idle/standby when active and configure force idle/standby
and disable clock when idled. This is taken care by the runtime framework when
driver calls the pm_runtime_get_sync and pm_runtime_put_sync APIs.
Need to configure MUSB into force standby and force idle mode when usb not used
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
OMAP4430 supports UTMI and ULPI types of transceiver interface.
In UTMI mode: The PHY is embedded within OMAP4430. The transceiver functionality
is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin
sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY
functionality is embedded within the OMAP4430.
There is no direct interactions between the MUSB controller and TWL6030
chip to communicate the session-valid, session-end and ID-GND events.
It has to be done through a software by setting/resetting bits in
one of the control module register of OMAP4430 which in turn toggles
the appropriate signals to MUSB controller.
musb driver is register for blocking notifications from the transceiver
driver to get the event notifications for connect/disconnect and ID-GND.
Based on these events call the transceiver init/shutdown function to
configure the transceiver to toggle the VBUS valid, session end and ID_GND
signals to musb and power on/off the internal PHY.
For ID_GND event notifications, toggle the ID_GND signal and then wait for
musb to be configured as "A" device, and then call the transceiver function
to set the VBUS.
In OTG mode and musb as a host, When the Micro A connector used, VBUS is turned on
and session bit set. When the device is connected, enumeration goes through.
When the device disconnected from the other end of the connector(ID is still grounded),
link will detect the disconnect and end the session. When the device is connected back,
there are no events generated in the TWL6030-usb, and link is already down.
So the device is not detected. Removed the session bit disable code which
will recognize the connect of the device.
Limitation: In OTG host mode, if device is connected during boot, it does not get
detected. If disconnect and connect it back or connect after boot only it works.
Fix for this, I will submit seperate patch later.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of using musb_platform_suspend/resume,
we can use dev_pm_ops and let the platform_device
core handle when to call musb_core's suspend and
glue layer's suspend.
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb core doesn't need to know about platform
specific details. So start moving clock
handling to platform glue layer and make
musb core agnostic about that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
that structure currently only holds a device
pointer to our own platform_device and musb's
platform_device, but soon it will hold pointers
to our clock structures and glue-specific bits
and pieces.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
preparing to a big refactor on musb code. We need
to be able to compile in all glue layers (or at
least all ARM-based ones) together and have a
working binary.
While preparing for that, we move every glue
layer to export only one symbol, which is
a struct musb_platform_ops, and make all
other functions static.
Later patches will come to allow for compiling
all glue layers together and have a working
binary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed the board_data parameter being
passed to musb_platform_init function
as board_data can be extracted from
device structure which is already member
of musb structure.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit 461972d8a4 (musb_core: don't call
musb_platform_exit() twice), unloading the driver module results in a WARNING
"kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being
called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode.
There exists dubious and unbalanced put_device() call in musb_free() which
takes place only in the OTG mode. As this commit caused musb_platform_exit()
to be called (and so unregister the NOP transceiver) before this put_device()
call, this function references already freed memory.
On the other hand, all the glue layers miss the otg_put_transceiver() call,
complementary to the otg_get_transceiver() call that they do. So, I think
the solution is to get rid of the strange put_device() call, and instead
call otg_put_transceiver() in the glue layers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This pin-muxing is best done in the board files. The driver should
not do this explicitly.
Also, this code causes a warning to be thrown when OMAP2430 and OMAP3/4
support are enabled in the same kernel.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need mach-types and hardware.h
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
get_cpu_rev() is unused in this driver. It is probably legacy
code. So remove it.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function is only called inside omap2430.c...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function does nothing...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Program the OTG_INTERFSEL register based on
transcevier type passed from board file.
Adapt signature of musb_platform_init() function
for davinci, blackfin and tusb6010.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate/unbalanced call to clk_put() from musb_platform_exit() --
clk_put() gets called from musb_core.c anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
we have those addresses already ioremaped, so let's
use our __raw_readl/writel wrappers.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Grazvydas Ignotas