In the link fail path, set IDEV_GONE for every device on the domain
when the last link in the port fails.
In the abort path functions like isci_reset_device, make sure that
there has not already been a detected domain failure with the device
by checking IDEV_GONE, before performing any kind of hard reset, SMP
phy control, or TMF operation.
The check for IDEV_GONE makes sure that the device in the abort path
really has control of the port with which it is associated. This
prevents starting hard resets at incorrect times and scheduling
unnecessary LUN resets for SATA devices.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ATAPI specific and STP general RNC suspension code had been
incorrectly removed from the remote device code.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Make sure that the wait for suspend can handle the RNC destruction case.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is an apparent HW lockup caused when the PE is disabled while there
is an outstanding TC in progress. This change puts the link into OOB to
force the TC to end before the PE is disabled.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This change adds timeouts to the RNC suspension wait. It makes the
suspend and resume timeouts the same.
The previous resume timeout of 5 ms was too short, and timeouts were
seen in resumptions of devices in the abort task/LUN reset path - which
would receive an RNC resumed message within a tenth of a second later.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Requests contructed as task management requests need to have the protocol
indicator set so the completion decode can observe any RNC suspension
conditions.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TMF requests, unlike normal I/O requests, need to handle I/O management
conditions in the completion function because TMFs are not handled in the
completion tasklet.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the case of TMF execution, or device resets, wait for the RNC to fully
resume before returning to the caller. This ensures that the remote
device will not fail I/O requests while waiting for the RNC resumption to
complete.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Instead of immediately transitioning to the SCI_RNC_AWAIT_SUSPENSION
state, handle the SCI_RNC_RESUMING suspend transition from the
SCI_RNC_READY state like the SCI_RNC_INVALIDATING --> SCI_RNC_POSTING
transitions do now, by setting the destination state for the entry
into the READY state.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When an individual request is being terminated, the request's tag
is managed in the terminate function.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch changes the callback mechanism to libsas to only occur while
the scic_lock is held; the abort path cleanup of I/Os also checks to make
sure IREQ_ABORT_PATH_ACTIVE is clear before proceding.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Completion of I/Os during the one of the abort path interface calls
from libsas can drive remote device state changes and the resumption
of the device RNC. This is a problem when the abort path is
attempting to cleanup outstanding I/O at the same time - the resumption
can prevent the termination from occuring correctly.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In order to prevent a device from receiving an I/O request while still
in an RNC suspending or resuming state (and therefore failing that
I/O back to libsas with a reset required status) wait for the RNC state
change before proceding in the abort path.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the libsas error path, SATA disks require extra handling in
libata to recover operation. However, libsas expects to be able
to immediately recover all outstanding I/O once the error handler
escalation stops. This patch fixes the condition where the libata
error handler is scheduled for operation but libsas has already
deleted the outstanding sas_tasks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The LLHANG timer should be enabled once per device. This patch corrects
both the timer enable and the timer disable for the remote device.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the case of a suspend call while in SCI_RNC_POSTING or INVALIDATING
states, the LLHANG detect needed to be saved so the upcoming suspension
would enable it correctly. The unused suspend callback parameters were
removed.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This addresses a regression from the commit "isci: Redesign
device suspension, abort, cleanup." in which the sas_task end
condition for terminated I/Os was made to call back on
sas_task_abort()".
This commit will be rolled into the original.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For NCQ error conditions among others, there is no need to enable
the link layer hang detect timer.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The RNC can be any of the states in the loop from suspended to
ready when the API "suspend" or "resume" are called. This change
adds destination states parameters that control the suspension /
resumption action of the RNC statemachine for those transition states.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This commit changes the means by which outstanding I/Os are handled
for cleanup.
The likelihood is that this commit will be broken into smaller pieces,
however that will be a later revision. Among the changes:
- All completion structures have been removed from the tmf and
abort paths.
- Now using one completed I/O list, with the I/O completed in host bit being
used to select error or normal callback paths.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If LUN reset sees that the device is gone, it returns TMF_RESP_FUNC_FAILED
to cause libsas to escalate to an I_T_Nexus_Reset.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fixing the remote device state machine to suspend and terminate
all outstanding I/O before the device stopped state is reached.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When the remote device enters the NCQ error state, the device must
be suspended so that the I/O terminations can take place.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TCs must be terminated only while the RNC is suspended. This commit
adds remote device suspensions and resumptions in the abort, reset and
termination paths.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TCs must only be terminated when RNCs are suspended.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add comprehensive decode for all TC completions that generate RNC
suspensions.
Note that this commit also removes unconditional resumptions of ATAPI
devices when in the SCI_STP_DEV_ATAPI_ERROR state, and STP devices
when in the SCI_STP_DEV_IDLE state. This is because the SCI_STP_DEV_IDLE
and SCI_STP_DEV_ATAPI state entry functions manage the RNC resumption.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The resumption from the Tx/Rx suspended state should work the same
as the Tx suspended state.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For STP devices under certain protocol conditions, an RNC will not
suspend until the current transfer state is broken with a SYNC/ESC
sequence from the SCU. The SYNC/ESC driven by expiration of the
SCU link layer hang detect timer, which has too small a dynamic
range to support slow SATA devices, so normally it is disabled.
This change enables the timer with the minimum period at the point
when the suspension is requested.
Note that there is potential collateral damage to other open
connections to slow SATA devices on the same port, since there
is no alternative but to enable the LLHANG timer on every phy in
the port for the current suspension request - there is no way to
tell on which phy the RNC in question is currently active.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
OEM parameters [1] are parsed from the platform option-rom / efi
driver. By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.
Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.
[1] the platform specific set of phy address, configuration,and analog
tuning values
[stable v3.0+]
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Ensure we enable receiving BCN's from the
hardware when adding phy to isci_port.
Otherwise if we get BCN before the port is
created we won't see any BCN
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Reported-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch extends timings in COMSAS signaling, so ISCI can detect disc
drives having issues to send COMSAS in correct time frame.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can retrieve the shost from the sas_ha like the rest of libsas and
drop this out of our local data structure.
Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is a (dubious?) lost irq workaround in sci_controller_isr() that
effectively nullifies attempts to disable interrupts. Until the
workaround can be re-evaluated add some infrastructure to prevent the
interrupt handler from inadvertantly re-enabling interrupts.
The failure mode was interrupts continuing to run after the driver had
been removed and its iomappings torn down.
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
[richard: clear remaining interrupts at the end of reset]
Acked-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The call to wait_for_start() is meant to ensure that all links have been
given a chance to come up before letting the kernel proceed with
probing. However, the implementation is not correctly syncing with the
port configuration agent. In the MPC case the ports are hard-coded, in
the APC case we need to wait for the port-configuration to form ports
from the started phys.
Towards that end increase the timeout for the APC agent to form ports,
and delay start complete until all phys are out of link-training.
Cc: <stable@vger.kernel.org>
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1/ notify waiters when controller stop completes (fixes 10 second stall
unloading the driver)
2/ make sure phy stop is after port and device stop
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Based on an original implementation by Ed Nadolski and Artur Wojcik
In preparation for S3/S4 support refactor initialization so that
driver-load and resume-from-suspend can share the common init path of
isci_host_init(). Organize the initialization into objects that are
self-contained to the driver (initialized by isci_host_init) versus
those that have some upward registration (initialized at allocation time
asd_sas_phy, asd_sas_port, dma allocations). The largest change is
moving the the validation of the oem and module parameters from
isci_host_init() to isci_host_alloc().
The S3/S4 approach being taken is that libsas will be tasked with
remembering the state of the domain and the lldd is free to be
forgetful. In the case of isci we'll just re-init using a subset of the
normal driver load path.
[clean up some unused / mis-indented function definitions in host.h]
Signed-off-by: Ed Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Per the SAS spec, several types of BROADCAST CHANGE primitives
must cause re-discovery of the originating expander.
Only the standard BROADCAST CHANGE primitive was being
sent to the LIBSAS layer. The other BC primitives have been
added to the sci_phy_event_handler()
Signed-off-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
domain_device ->parent conveys the same information.
Occurrences of ->is_direct_attached appear next to incomplete open-coded
versions of dev_is_sata(), clean those up as well.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Convert controller state machine warnings to emit the state number (it
missed the number to string conversion, but since these error rarely
happen not much motivation to go further).
Fix up the rnc warnings to use the state name.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With the exception of the detached field, sg_mutex no longer adds any
locking. detached handling has been broken before and is still broken
and this patch does not seem to make things worse than they were to
begin with.
However, I have observed cases of tasks being blocked for >200s waiting
for sg_mutex. So the removal clearly adds value for very little cost.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sfds is protected by sg_index_lock - except for sg_open(), where it
isn't. Change that and add some documentation.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changes since v1: set_exclude now returns the new value, which gets
rid of the comma expression and the operator precedence bug. Thanks
to Douglas for spotting it.
sdp->exclude was previously protected by the BKL. The sg_mutex, which
replaced the BKL, only semi-protected it, as it was missing from
sg_release() and sg_proc_seq_show_debug(). Take an explicit spinlock
for it.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
srp->done is protected by sfp->rq_list_lock everywhere, except for this
one case. Result can be that the wake-up happens before the cacheline
with the changed srp->done has arrived, so the waiter can go back to
sleep and never be woken up again.
The wait_event_interruptible() means that anyone trying to debug this
unlikely race will likely notice everything working fine again, as the
next signal will unwedge things. Evil.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
After sg_release() has been called, noone should be able to actually use
that filedescriptor anymore. So if closed ever made a difference in the
past five years or so, it would have meant a bug. Remove it.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
[jejb: fix up checkpatch warnings]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Afaics the use of __wait_event_interruptible() as opposed to
wait_event_interruptible() is purely historic. So let's follow the rest
of the kernel and check the condition before prepare_to_wait() - and
also make the code a bit nicer.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The while (1) construct isn't actually a loop at all. So let's not
pretent and obfuscate the code.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
blocking is de-facto a constant and the now-removed comment wasn't all
that useful either. Without them and the resulting indentation the code
is a bit nicer to read.
Signed-off-by: Joern Engel <joern@logfs.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dial back the aggressiveness of the controller lockup detection thread.
Currently it will declare the controller to be locked up if it goes
for 10 seconds with no interrupts and no change in the heartbeat
register. Dial back this to 30 seconds with no heartbeat change, and
also snoop the ioctl path and if a firmware flash command is detected,
dial it back further to 4 minutes until the firmware flash command
completes. The reason for this is that during the firmware flash
operation, the controller apparently doesn't update the heartbeat
register as frequently as it is supposed to, and we can get a false
positive.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use spinlocks with finer granularity in the submission and
completion paths to allow concurrent execution for multiple
reply queues. In particular, do not hold a spin lock while
submitting a request to the device, nor during most of the
interrupt handler.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Smart Arrays can support multiple reply queues onto which command
completions may be deposited. It can help performance quite a bit
to arrange for command completions to be processed on the same CPU
from which they were submitted to increase the likelihood of cache
hits.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is in order to smooth the way for upcoming changes to allow use of
multiple reply queues for command completions.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When aborting a command, the tag is supposed to be
specified as 64-bit little endian. However, some smart
arrays expect the tag of the command to be aborted to be
specified in a strange byte order. How to tell which sort
of Smart Array firmware we're dealing with is not obvious.
However, because of the way we construct our tags, the values
of any outstanding tag when specified with the "strange" byte
order will not collide with the value specified in the correct
order. That means we can safely attempt the abort both ways.
Signed-off-by: Stephen M. Cameron <stephenmcameron@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of giving up after 3 immediate retries of driver initiated
commands, back off the rate of retries and retry a bunch more times.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reviewed-by: Andi Shyti <andi.shyti@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In shared SAS configurations we might get a busy status
during driver initiated commands (e.g. during rescan for
devices). We should retry the command in such cases rather
than giving up.
Signed-off-by: Matt Bondurant <Matthew.dav.bondurant@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
MSI/MSI-X interrupts can't race the DMA completion they are communicating
so no need to read from controller to flush the DMA to the host if
MSI or MSI-X interrupts are being used.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Default behavior for any CHECK CONDITION excepting a few special cases is to
print out certain parts of the sense buffer and the CDB. Default behavior
should be to print nothing and let the upper layers or applications decide what
to do about these. The same information is already available by setting the
appropriate bits of the scsi_logging_level kernel parameter or via
/proc/sys/dev/scsi/logging_level.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
pci_disable_device() disables the bus master bit and pci_enable_device does
not re-enable it. It needs to be enabled.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There was code to skip "disabled" devices which was intended to
skip devices disabled in the BIOS, but it really just checks to
see if the device can write to host memory, which this is disabled
by pci_disable_device on driver unload, so this check has the effect
of preventing subsequent load of the driver. And devices disabled in
the BIOS don't show up at all anyway, so this check never made any
sense to begin with, and should be removed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As Jenx Axboe explained to me: "In earlier times (2.6.18 and pre, iirc), Linux
disabled IO and mem bars on pci_disable_device(). Now in newer kernel it does
not. And in the newer kernels you run into problems if you DON'T disable the
device on exit, since when it later loads the device is already in the enabled
state - and pci_enable_device() then does nothing. This typically screws
MSI/MSI-X." This is what the big scary comment that says pci_disable_device
does "something nasty" to smart arrays was evidently referring to.
If pci_disable_device is not called on driver rmmod, subsequently insmod'ing
the driver may in result in some cases fail to be able to receive interrupts,
esp. if other drivers are loaded between unloading and loading hpsa.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Check the domain validation flag on the given device before referencing
scsi_device instance, otherwise if the flag is already set we return without
decrementing the reference count.
Signed-off-by: Mike Maslenkin <mihailm@parallels.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Old version: 2.7.0.3
New version: 2.7.2.2
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This will set the target can_queue limit to the number of preallocated
session tasks set during creation.
"Could not send nopout" messages were observed without this when the
iSCSI connection experiences dropped frames under heavy I/O stress.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a followup to a patch provided by Jack Wang on September 21 2011.
After increasing the CAN_QUEUE to 510 in pm8001 we discovered some performance
degredation from time to time. We needed to increase the MPI queue to
compensate and ensure we never hit that limit. We also needed to double
the margin to support event and administrivial commands that take from
the pool resulting in an occasional largely unproductive command completion
with soft error to the caller when the command pool is overloaded temporarily.
Signed-off-by: Mark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
UTP Transfer request list base registers UTRLBA and UTRLBAU
must be assigned, lower-32 and upper-32 bits of UTRLD list
physical base addresses respectively.
Currently UTRLBAU is being assigned lower-32 bits of UTRLD
physical base address. This will cause an issue with
controllers that can support 64-bit addressing.
This patch correctly assigns upper-32 bits of UTRLD physical
base address to UTRLBAU.
Reported-by: Rene De Jong <rene.dejong@arm.com>
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Reviewed-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We moved the locking in dd060e74fb "[SCSI] fcoe: remove frame dropping
code from fcoe_percpu_clean" but this unlock was missed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC-BB-6 v1.04 7.9.8.14 N_Port_ID Beacon:
"A N_Port_ID Beacon is multicast and uses the VN_Port MAC address as source
address."
Currently, libfcoe is using ENode MAC, this seems ok and functionality wise
not a problem in my back to back testing setup, however, just fix this to
make libfcoe VN2VN support more spec compliant.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The rtnl_mutex was held to protect calls to dev_uc_add
and dev_uc_del. Holding rtnl is not required as those
functions make use of the netif_addr_lock* API to
protect the MAC changing.
This change fixes the following regression by removing
the rtnl usage when fcoe_update_src_mac is called.
https://bugzilla.kernel.org/show_bug.cgi?id=42918
the existing dependency chain (in reverse order) is:
-> #1 (&fip->ctlr_mutex){+.+...}:
[<c1091f70>] lock_acquire+0x80/0x1b0
[<c147655d>] mutex_lock_nested+0x6d/0x340
[<f8970c32>] fcoe_ctlr_link_up+0x22/0x180 [libfcoe]
[<f894620e>] fcoe_create+0x47e/0x6e0 [fcoe]
[<f8973dd3>] fcoe_transport_create+0x143/0x250 [libfcoe]
[<c10527e0>] param_attr_store+0x30/0x60
[<c1052696>] module_attr_store+0x26/0x40
[<c11a201e>] sysfs_write_file+0xae/0x100
[<c11449df>] vfs_write+0x8f/0x160
[<c1144cbd>] sys_write+0x3d/0x70
[<c147a0c4>] syscall_call+0x7/0xb
-> #0 (rtnl_mutex){+.+.+.}:
[<c109164b>] __lock_acquire+0x140b/0x1720
[<c1091f70>] lock_acquire+0x80/0x1b0
[<c147655d>] mutex_lock_nested+0x6d/0x340
[<c13a10c4>] rtnl_lock+0x14/0x20
[<f89445ac>] fcoe_update_src_mac+0x2c/0xb0 [fcoe]
[<f8971712>] fcoe_ctlr_timer_work+0x712/0xb60 [libfcoe]
[<c104fb69>] process_one_work+0x179/0x5d0
[<c10502f1>] worker_thread+0x121/0x2d0
[<c10550ed>] kthread+0x7d/0x90
[<c1481a82>] kernel_thread_helper+0x6/0x10
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&fip->ctlr_mutex);
lock(rtnl_mutex);
lock(&fip->ctlr_mutex);
lock(rtnl_mutex);
*** DEADLOCK ***
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The fcoe controller has back references, therefore defer
releasing master lport which gets freed along scsi_host_put
and then free it once fcoe interface is fully cleaned.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove lport from net device and then do synchronize net device to flush
inflight rx frames for the lport before doing fcoe_percpu_clean.
In case of master lport, remove all rx packet handlers completely and
then only do fcoe_percpu_clean. This required splitting fcoe_interface_cleanup
to do remove part separately and for that added func fcoe_interface_remove
and then call it from fcoe_if_destory before doing fcoe_percpu_clean.
However if fcoe_interface_remove() is already called then
don't call again from fcoe_interface_cleanup() to preserve its
existing flows.
This patch along with Neil's other patch to avoid soft irq context
on ingress will avoid passing up frames on disabled lport as
discussed in this mail thread:-
http://lists.open-fcoe.org/pipermail/devel/2012-February/011947.html
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While interpreting the result of UTP task completion status,
by using boolean &&, the evaluation would fail when the
UPIU_TASK_MANAGEMENT_FUNC_SUCCEEDED was received.
Either UPIU_TASK_MANAGEMENT_FUNC_COMPL or
UPIU_TASK_MANAGEMENT_FUNC_SUCCEEDED should be
considered as a success result.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When scsi_add_host fails the scsi_host_put should be called.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When a rport is added back or the role is changed the fc class
will queue a scan and then call scsi_target_unblock. The problem
with this is if the devices are in the SDEV_OFFLINE state and
the scan is run before the scsi_target_unblock, then the scan
will see LUN0 as offline and the scan will fail. This patch moves
the unblock call to before the scan, so we know the device state
will be set correctly when the scan is run.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is a memory leak in the st driver when sending large enough reads or
writes using st's direct I/O path. As part of mapping the application's
memory, a buffer to hold page pointers is allocated and the count of mapped
pages is stored in field do_dio. A non-zero do_dio marks that direct I/O is
in use.
But do_dio is only 1 byte in size. Mapping 256 4k pages overflows
do_dio and causes it to be set to 0, like direct I/O option was not
used. When the I/O completes, the buffer to hold the page pointers is
not freed, and the page counts of the mapped pages are not reduced.
Every I/O of this size then leaks memory.
The size of do_dio needs to be increased to prevent it wrapping around.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix a use-after-free in the TMF path, where cmd may have been already
freed by virtscsi_complete_free when wait_for_completion restarts
executing virtscsi_tmf. Technically a race, but in practice the command
will always be freed long before the completion waiter is awoken.
The fix is to make callers specifying a completion responsible for
freeing the command in all cases.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 6f381fa344
Author: Lin Ming <ming.m.lin@intel.com>
[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
Caused a regression where we oops in every legacy mode SCSI host driver
because they supply a NULL pointer to scsi_add_host(). Fix this by checking
for the NULL in scsi_add_host_with_dma() and changing the DMA device to being
the platform_bus in that case (which replicates the original behaviour).
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of firmmware detected under-run condition and scsi status of
task_set_full or busy_condition, return that to the mid layer for proper error
handling instead of DID_ERROR (which causes error handler activation and a
full retry).
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
release_firmware() checks for NULL pointers internally so checking
before calling the function is redundant.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
release_firmware() checks for NULL pointers internally so checking
before calling it is redundant.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
release_firmware() checks for NULL pointers internally, so checking
before calling the function is redundant.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Made changes to have the same logging level for Logical port
online and offline events, to display these events in pairs.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make changes to remove unsupported model numbers from the sysfs
model description routine.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to avoid queuing the vport delete work to IM driver
work queue in the bfa_fcb_lport_delete() - since at this stage we
are not completely done with using the vport structure as we are
still waiting for the LOGO response from the fw in online state or
just doing some cleanup. Since queuing up the vport delete work at
this stage will result in the FC transport layer to clean up the vport
before we get the response from firmware.
Made changes to queue the port delete work to the IM driver work queue -
from the bfa_fcs_vport_free() function since at this state we are done
with using the vport data structure and the FCS state machine is completely
cleaned up.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hyper-V cannot process some commands like ATA_12 and ATA_16. It also returns a
very generic error when this happens (SRB_STATUS_ERROR). Most of the time we
treat SRB_STATUS_ERROR as DID_TARGET_FAILURE which causes error handler retry,
but in the case of pass through commands, they'll never succeed (and the error
handler will offline the device), so put a discriminating block in the command
completion routing and send the SRB_STATUS_ERROR upwards with DID_PASSTHROUGH
for commands we know should not be retried.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implement ISCSI_HOST_PARAM_PORT_STATE and ISCSI_HOST_PARAM_PORT_SPEED
to get the Adapter port state and port name
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch allows iscsiadm to set/ delete static IP and enable /disable
DHCP.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implement the ISCSI_HOST_PARAM_INITIATOR_NAME for .get_host_param
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The async handle corresponding to unknown Opcode was not freed
earlier. This code does the fix for that.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For each ASYNC PDU received there is an HDR and DATA handle for it.
There will be only 1 HDR ASYNC Handle, but DATA Handle can be more
than 1 for each ASYNC PDU received. Checking if the ASYNC Handle
correspongs to HDR or DATA while returning the Handle to the free list.
hwi_free_async_msg just return the handles to the free list. No return
values are needed so changing the return type to void.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change MODULE_AUTHOR, driver name and other external print strings from
Serverengines to Emulex.
Signed-off-by: Minh Tran <MinhDuc.Tran@Emulex.Com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of MCC_Q creation failed, the MCCQ info memory is freed
from be_mcc_queues_destroy and be_mcc_queues_create. This caused
kernel to panic because of double free.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The WRB and SGL Handle allocated for Login task were not freed
back to the pool after the login process was done. This code
releases the WRB and SGL Handle after the login process.
v2:
- Fix up locking so bh calls are not done when not needed.
- Make beiscsi_cleanup_task static.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
[various fixes]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removing code duplication during the WRB_Handle and WRB
initialization.
Added memory allocation failure handling code during WRB
initialization.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The buffer length passed for processing the ASYNC PDU
was not proper.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Set the ASYNC PDU Handle pBuffer for Data ring with the VA/PA
of the allocated memory for it.
To get the correct ASYNC PDY Handle iterate the list and compare
the PA set during initialization with the passed PHY Address.
The buffer_size and num_enteries are common for HDR and Data ring
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A previous commit changed the mfs checking to ensure the new
mfs is less or equal to the mfs supported by the FCF. This
doesn't work for BRDCM cards as they set an mfs of 2048 regardless
of whether the switch returns a larger mfs.
This patch validates the new mfs against the upper and lower spec
defined boundries for a FCoE mfs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use check_signature to find a signature in the mmio address.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The patch 116046127d "[SCSI] aacraid: Added
Sync.mode to support series 7/8/9 controllers" removed an iounmap call from
aac_src_ioremap. Before that, the iounmap has been called twice with the same
value (dev->base and dev->regs.src.bar0) and the iounmap complained about it
(iounmap: bad address ...).
The proper solution is a change the paremeter from bar0 to bar1.
Fix this by adding a an iounmap(dev->regs.src.bar1) call.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Achim Leubner <achim_leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch optimizes the set target port group(STPG) command. During our
testing, we found that it is not optimal to send stpg command every time
the path group switch happens. This patch uses PREF (preferred target port)
bit with combination of flags passed by multipath user level tool to
optimize this behaviour. If PREF bit is set then it issues a STPG command,
otherwise it will let implicit transfer take place.
By default there is no change in the behaviour. User tool needs to pass the
parameter to make this change take effect. Patch has been tested on NetApp
E series storage.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
PREF bit indicates preferred target port group for accessing a logical
unit. This bit is used to optimize the STPG command handling.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Handler expects only one parameter to set the flag ALUA_OPTIMIZE_STPG.
This flag is used to optimize the STPG behaviour. There is no change in
behaviour by default.
For example, to set the flag pass the following parameters from multipath.conf
hardware_handler "2 alua 1"
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The ioc->pfacts member in the IOC structure is getting set to zero
following a call to _base_get_ioc_facts due to the memset in that routine.
So if the ioc->pfacts was read after a host reset, there would be a NULL
pointer dereference. The routine _base_get_ioc_facts is called from context
of host reset. The problem in _base_get_ioc_facts is the size of
Mpi2IOCFactsReply is 64, whereas the sizeof "struct mpt2sas_facts" is 60,
so there is a four byte overflow resulting from the memset.
Also, there is memset in _base_get_port_facts using the incorrect structure,
it should be "struct mpt2sas_port_facts" instead of Mpi2PortFactsReply.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
CC: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Following the host reset, the firmware discovery is reassigning another hard
drive in the topology to the same device handle as that device is getting hot
removed. Until the driver device removal routine is called, there will be two
hard drive with the matching device handle in the internal device link
list. In the device removal routine, a separate function which moves the
device from BLOCKED into OFFLINE state. Since this routine is passed with the
device handle passed as input parameter, the routine will be traversing the
internal device link list searching for matching device handle. This results
in two devices with matching device handle, therefore both devices goes
OFFLINE.
To fix this issue,the input parameter is changed from device handle to SAS
address, therefore only the device that is hot unplugged will be placed in
OFFLINE state.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The phy_identifier inside the routine _transport_set_identify()
is set to sas_device_page_zero->PhyNum. This returns the
phy number of the parent device this device is linked to.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The port number is changing after disabling/enabling phys using the SysFS
interface This is because the firmware behavour changed where it would read
the the port number then set it to some different value even though Auto Port
Config is turned on. With this change of behavour in FW, it is possible that
the expanders are moved from one port to another after disabling /enabling
phys. This is occuring because the port number in sas iounit page 1 is not
matching up to the current port in page 0. In order to fix this the driver is
modified to read the current port number from sas iounit page 0 instead of
page 1. Also copy the port and phy flags over from page 0 to page 1.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix several endian issues found by runing sparse.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Modified the source code as per the findings reported by the source
code analysis tool. Source code for the following functionalities
has been touched. None of the driver functionalities has changed.
- SMP Passthrough IOCTL
- Debug messages for MPT Replies (i.e. bit 9 of Logging Level)
- Task Management using sysfs
- Device removal, i.e. when a target device (including any PD within a volume)
is removed, and Volume Deletion.
- Trace Buffer
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There were possible race conditions surrounding reading an object
from the link list while from another context in the driver was
removing it. The nature of this enhancement is to rearrange locking
so the link lists are better protected.
Change set:
(1) numerous routines were rearranged so spin locks are held through
the entire time a link list object is being read from or written to.
(2) added new routines for object deletion from link list. Thus ensuring
lock was held during the deletion of the link list object, then and memory
for object freed outside the lock. The memory was freed outside the lock
so driver had access to device object info which was required for
notifying the scsi mid layer that a device was getting deleted.
(3) added the ioc->blocking_handles parameter. This is a bitmask used
to identify which devices need blocking when there is device loss. This was
introduced so that lock can be held for the entire time traversing the link
list objects, and the bitmask was set to indicate which device handles need
blocking. Oustide the lock the ioc->blocking_handles bitmask is traversed,
with the respective device handle the scsi mid layer is called for moving
devices into blocking state.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support for Block IO requests with multiple segments (vectors) in
the SMP handler of the SAS Transport Class. This is required by the
BSG driver. Multisegment support added for both, Request and Response.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the lock_kernel and unlock_kernel routines were removed in the
2.6.39 kernel, a global mutex was added on top of the existing mutex
which already existed. With this implementation, only one IOCTL
will be active at any time no matter how many ever controllers
are present. This causes poor performance.
Removed the global mutex so that the driver can work with the existing
semaphore that was already part of the existing code.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changeset in MPI headers:
1) Bumped MPI2_HEADER_VERSION_UNIT
2) Added 4K sectors supported bit to CapabilitiesFlags field of IOC Page 6.
3) Added UEFIVersion field to BIOS Page 1 and defined additional
BiosOptions bits to control UEFI behavior.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas updates the driver version to
v00.00.06.15-rc1, and updates Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas fixes the fastpath code decision
logic to use fpRead/WriteCapable, fpRead/WriteAcrossStripe flags
instead of the old logic. This fixes a bug where fastpath writes
could be sent to a read only LD.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas removes an incorrect comment and
optimizes the setting of HostMSIxVectors. This was found during a
code review by Tomas Henzl @ RedHat.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Data type of the 'tag' field of 'fw_flash_Update_resp' should be __le32.
Data type of 'pHeader' should be __le32. Remove 2nd cast to 'piomb'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit a692b0eec5.
Tom reports:
[ 8.741033] ------------[ cut here ]------------
[ 8.741038] WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0xc1/0xf0()
[ 8.741040] Hardware name: To Be Filled By O.E.M.
[ 8.741041] sysfs: cannot create duplicate filename
...and missing 2 out of 4 drives connected to mvsas. Commit a692b0ee
made the assumption that all the phy ids an lldd registers to libsas are
unique. However, in the "multi-chip" case mvsas does a rather annoying
duplication of phy ids in the array passed to libsas. So, for example,
chip0 has phy0-3 at ha phy index 0-3 and chip1 has its phy0-3 at ha phy
index 4-7. The more natural model would be to create a scsi_host (and
sas_ha) per chip (controller), but for now revert the naming fix which
unfortunately means dealing with unpredictable end-device names for a
bit longer.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Cc: Patrick Thomson <patrick.s.thomson@intel.com>
Reported-by: Tom Rini <trini@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Normalize phy->attached_sas_addr to return a zero-address in the case
when device-type == NO_DEVICE or the linkrate is invalid to handle
expanders that put non-zero sas addresses in the discovery response:
sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device)
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This changes the ordering of initialization and probing events from:
1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
3/ schedule port probe in DISCE_PROBE
This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:
BUG: unable to handle kernel paging request at 0000000000003b10
IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
...
[<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
[<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
[<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
[<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
[<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]
...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.
Reported-by: Michal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The check_ready implementation in the expander-attached ata device case
polls on sas_ex_phy_discover(). The effect is that the ex_phy fields
(critically ->attached_sas_addr) can change. When ata_eh ends and
libsas comes along to revalidate the domain
sas_unregister_devs_sas_addr() can fail to lookup devices to remove, or
fail to re-add an ata device that ata_eh marked as disabled. So change
the code to skip the sas_address and change count updates when ata_eh is
active.
Cc: Jack Wang <jack_wang@usish.com>
Tested-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 899fcf4 "[SCSI] libsas: set attached device type and target
protocols for local phys" setup 'phy' to be dereferenced after
list_for_each_entry(phy, &port->phy_list, port_phy_el) (i.e. phy ==
&port->phy_list) resulting in reports like:
BUG: unable to handle kernel NULL pointer dereference at 00000000000002b0
IP: [<ffffffffa00ce948>] sas_discover_domain+0x29e/0x4fb [libsas]
...fix by deferring sas_phy_set_target() to the end of
sas_get_port_device().
Reported-by: Tom Jackson <thomas.p.jackson@intel.com>
Tested-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If an expander reports 'PHY VACANT' for a phy index prior to the one
that generated a BCN libsas fails rediscovery. Since a vacant phy is
defined as a valid phy index that will never have an attached device
just continue the search.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When requeuing work to a draining workqueue the last work instance may
not be idle, so sas_queue_work() must not touch work->entry. Introduce
sas_work with a drain_node list_head to have a private list for
collecting work deferred due to drain collision.
Fixes reports like:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff810410d4>] process_one_work+0x2e/0x338
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It was documented in Documentation/m68k/kernel-options.txt and
Documentation/scsi/scsi-parameters.txt, but the implementation was
missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitzmic@googlemail.com>
Cc: James E.J. Bottomley <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
Currently, __scsi_alloc_queue uses SCSI host's parent device
as DMA device to set segment boundary. But the parent device may not
refer to the DMA device. For example, for ATA disk, SCSI host's parent
device now refers to ATA port.
Since commit d139b9b([SCSI] scsi_lib_dma: fix bug with dma maps on
nested scsi objects), a new field Scsi_Host->dma_dev was introduced
to refer to the real DMA device.
Use ->dma_dev in __scsi_alloc_queue to correctly set segment
boundary.
Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2
Reported-and-tested-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 18a4d0a22e ("[SCSI] Handle disk devices which can not process
medium access commands") introduced a bug in which we would attempt to
dereference the scsi driver even when the device had no ULD attached.
Ensure that a driver is registered and make the driver accessor function
more resilient to errors during device discovery.
Reported-by: Elric Fu <elricfu1@gmail.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
Emit the function name not the address when possible.
builtin_return_address() gives an address. When building
a kernel with CONFIG_KALLSYMS, emit the actual function
name not the address.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
=IH8T
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Pull a few more things for powerpc by Benjamin Herrenschmidt:
- Anton's did some recent improvements to EPOW event reporting on
pSeries (power supply failures and such). The patches are self
contained enough and replace really nasty code so I felt it should
still go in
- I did the vio driver registration change Greg requested, I don't see
the point of leaving that til the next merge window
- The remaining EEH changes I said were still pending to get rid of the
EEH references from the generic struct device_node
- A few more iSeries removal bits
- A perf bug fix on 970
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: Fix instruction address sampling on 970 and Power4
powerpc+sparc/vio: Modernize driver registration
powerpc: Random little legacy iSeries removal tidy ups
powerpc: Remove NO_IRQ_IGNORE
powerpc/pseries: Cut down on enthusiastic use of defines in RAS code
powerpc/pseries: Clean up ras_error_interrupt code
powerpc/pseries: Remove RTAS_POWERMGM_EVENTS
powerpc/pseries: Use rtas_get_sensor in RAS code
powerpc/pseries: Parse and handle EPOW interrupts
powerpc: Make function that parses RTAS error logs global
powerpc/eeh: Retrieve PHB from global list
powerpc/eeh: Remove eeh information from pci_dn
powerpc/eeh: Remove eeh device from OF node
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
The latest generation of ipr hardware performs best when command blocks
are aligned to a boundary equal to the size of the command block. Ensure
512 byte alignment, since this is the largest size command block we
can send.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Increase the total number of max concurrent outstanding commands
for the most recent family of adapters in order to improve overall
adapter performance.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The ipr driver added some memory barriers in order to ensure
a PowerPC sync instruction was executed prior to sending a
command to the adapter to ensure the command block was
coherent with respect to the PCI bus's view of memory.
However, some time ago, the powerpc architecture writel
macros were changed to include the sync since most drivers
don't properly handle this. So remove these memory barriers
since they are not needed and result in executing twice
as many sync instructions, which has a significant performance
penalty.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The latest ipr hardware no longer requires the driver to issue any MMIOs
to clear the interrupt so remove this to optimize performance.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For the latest ipr SAS adapters, target id's are a completely
logical construct that are managed in the ipr driver. This fixes
an issue that can arise if a device is deleted via sysfs. If
a new device is then physically added, it will use the previous
device's target id. If the host is then rescanned, the device
that had been deleted, since it is using the same target id as
the new device is using, will never be found, resulting in
a missing device. Fix this by only freeing the target id
only if the resource is actually gone.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
commit 44c10138fd (PCI: Change all
drivers to use pci_device->revision) converted all drivers to use
pci_dev->revision. Convert these three drivers which got missed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The rtnl_lock is primarily used to serialize networking
driver changes as well as to ensure that a networking driver
is not removed when making changes to it. fcoe also uses
the rtnl_lock to protect the fcoe hostlist.
fcoe_create holds the rtnl_lock over the entirity of the
routine including a the call to fcoe_ctlr_link_up.
This causes the below deadlock because fcoe_ctlr_link_up
acquires the fcoe_ctlr ctlr_mutex and this deadlocks with
a libfcoe thread that acquires the fcoe_ctlr ctlr_mutex and
then the rtnl_lock (to update a MAC address).
This patch drops the rtnl_lock before calling
fcoe_ctlr_link_up and therefore the deadlock is prevented.
https://bugzilla.kernel.org/show_bug.cgi?id=42918
the existing dependency chain (in reverse order) is:
-> #1 (&fip->ctlr_mutex){+.+...}:
[<c1091f70>] lock_acquire+0x80/0x1b0
[<c147655d>] mutex_lock_nested+0x6d/0x340
[<f8970c32>] fcoe_ctlr_link_up+0x22/0x180 [libfcoe]
[<f894620e>] fcoe_create+0x47e/0x6e0 [fcoe]
[<f8973dd3>] fcoe_transport_create+0x143/0x250 [libfcoe]
[<c10527e0>] param_attr_store+0x30/0x60
[<c1052696>] module_attr_store+0x26/0x40
[<c11a201e>] sysfs_write_file+0xae/0x100
[<c11449df>] vfs_write+0x8f/0x160
[<c1144cbd>] sys_write+0x3d/0x70
[<c147a0c4>] syscall_call+0x7/0xb
-> #0 (rtnl_mutex){+.+.+.}:
[<c109164b>] __lock_acquire+0x140b/0x1720
[<c1091f70>] lock_acquire+0x80/0x1b0
[<c147655d>] mutex_lock_nested+0x6d/0x340
[<c13a10c4>] rtnl_lock+0x14/0x20
[<f89445ac>] fcoe_update_src_mac+0x2c/0xb0 [fcoe]
[<f8971712>] fcoe_ctlr_timer_work+0x712/0xb60 [libfcoe]
[<c104fb69>] process_one_work+0x179/0x5d0
[<c10502f1>] worker_thread+0x121/0x2d0
[<c10550ed>] kthread+0x7d/0x90
[<c1481a82>] kernel_thread_helper+0x6/0x10
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&fip->ctlr_mutex);
lock(rtnl_mutex);
lock(&fip->ctlr_mutex);
lock(rtnl_mutex);
*** DEADLOCK ***
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to set the rport maxfrsize param to use a value that is
equal to or less than the Buffer-to-Buffer Receive Data_Field size
specified in the Common Service Parameters.
Increased the diag memtest timeout for the Brocade-1860 adapters.
Made changes to enable valid port speed configuration check for all adapters.
Made changes to increase the max hw segments in a request, in order to
support larger data transfers from user space.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed the LPS (Logical Port Services) state machine to send a
FDISC/FLOGI to the FW from the request queue wait state, when
there is space available again on the request queue.
Made changes to free the vport on LOGO/cleanup complete instead
of free'ing it from vport_delete_handler in the module unload scenario.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Programming of the service parameters Tx credits etc., is now done in firmware.
Remove the logic of sending the service parameters to firmware from driver.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to the Fabric Assigned Address(FAA) feature implementation.
Introduced the IOCFC state machine, which now handles the FAA logic,
IOC and BFA sub-modules enablement.
Removed un-wanted FAA enable/disable routines; FAA is enabled by default.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to resume the flash controller if it is halted before going
ahead with flash controller pause/resume logic.
Made changes to avoid clearing off the interrupts during the initial
pll initialization.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to ensure only the function that comes first will execute
the IOC hw semaphore unlock logic.
Used IOC init sem register to serialize execution of the unlock logic.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to the driver ISR to process any pending completions even if
the RME bit is not set in the interrupt status register.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fix ensures that the IOP_LOGINFO_CODE_TASK_TERMINATED
messages do not clutter the sas_log_info messages.
Bugzilla 42142 - mpt2sas: Number specified in wrong base
https://bugzilla.kernel.org/show_bug.cgi?id=42142
Signed-off-by: Sathisha Nanjappa <sathisha.nanjappa@hp.com>
Acked-by: "Nandigama, Nagalakshmi" <Nagalakshmi.Nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Starting fcoe fails at fcoe_transport_create when attempting to allocate a
pool of 4K exchanges on a 64-bit single-CPU environment because the call to
__alloc_percpu() is greater than the max of 32K. This patch reduces the
number of exchanges to fit within the maximum allowed space.
[ Whitespace problems fixed by Robert Love to satisfy chechpatch.pl ]
Signed-off-by: Steven Clark <sclark@crossbeam.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is potentially lots of contention for the rx_list_lock. On a cpu that is
receiving lots of fcoe traffic, the softirq context has to add and release the
lock for every frame it receives, as does the receiving per-cpu thread. We can
reduce this contention somewhat by altering the per-cpu threads loop such that
when traffic is detected on the fcoe_rx_list, we splice it to a temporary list.
In this way, we can process multiple skbs while only having to acquire and
release the fcoe_rx_list lock once.
[ Braces around single statement while loop removed by Robert Love
to satisfy checkpath.pl. ]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
commit e7a51997da ([SCSI] fcoe: flush per-cpu
thread work when destroying interface) added a skb flush to the fcoe_rx_list,
which ensures that we push any pending frames on the list through the per-cpu
receive thread. Because of this, its redundant to lock and scan the list
first, dropping any arriving frames.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As with the fcoe sw transport, the bnx2fc packet handler function runs only in
softirq context. Theres no need to disable bottom halves here
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The fcoe sw recive packet function (fcoe_rcv) only ever executes in softirq
context. Given that, and the fact that no use of the fcoe_rx_list is made in
irq context, its not necessecary to disable bottom halves while actually
receiving the frame. Convert spin_*_bh calls in that function to their
lock-only equivalents
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some switch implementations (eg., HP virtual connect FlexFabric) send two MAC
descriptors in FIP FLOGI response, with first MAC descriptor (granted_mac) used
as FPMA, and the second one (fcoe_mac) used as destination address for
sending/receiving FCoE packets. fip_mac continues to be used for FIP traffic.
This patch introduces fcoe_mac in fcoe_fcf structure. For regular switches,
both fcoe_mac and fip_mac will be the same. For the switches that send
additional MAC descriptor, fcoe_mac is updated.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently fc_host mfs is not getting updated in
case its changed during FLOGI and that leaves fc_host
to show its initial old value in sysfs, so instead
have fc_host mfs updated along with updating lport mfs
during FLOGI.
Also in case of bad mfs during flogi, error out
instead of continuing with flogi.
[ Changes made by Robert Love: condition to '>=' and
added printing of lport->mfs in DBG statement. FLOGI
resp processing failed without being able to compare
FCoE MFS 2112 against an incoming MFS of 2112 ]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When handling CVL with no Vx port descriptors, lports for NPIV ports are reset
before issuing the ctlr_reset. This causes FDISCs to be issued before
successful FLOGI. Fix it by resetting the controller before resetting the
lports.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
commit 859b7b649a introduced the ability to call
fcoe_recv_frame in softirq context. While this is beneficial to performance,
its not safe to do, as it breaks the serialization of access to the lport
structure (i.e. when an fcoe interface is being torn down, theres no way to
serialize the teardown effort with the completion of receieve operations
occuring in softirq context. As a result, lport (and other) data structures can
be read and modified in parallel leading to corruption. Most notable is the
vport list, which is protected by a mutex, that will cause a panic if a softirq
receive while said mutex is locked. Additionaly, the ema_list, discussed here:
http://lists.open-fcoe.org/pipermail/devel/2012-February/011947.html
Can be corrupted if a list traversal occurs in softirq context at the same time
as a list delete in process context. And generally the lport state variables
will not be stable, and may lead to unpredictable results.
The most direct fix is to remove the bits from the above commit that allowed
fcoe_recv_frame to be called in softirq context. We just force all frames to be
handled by the per-cpu rx threads. This will allow the fcoe_if_destroy's use of
fcoe_percpu_clean to function properly, ensuring that no frames are being
received while the lport is being torn down.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
This makes vio_register_driver() get the module owner & name at compile
time like PCI drivers do, and adds a name pointer directly in struct
vio_driver to avoid having to explicitly initialize the embedded
struct device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Fetch the config page from the device to learn max target id to set
host->max_id.
Also, fix some indentation issues and update the 'Maintained by' field.
Signed-off-by: Arvind Kumar <arvindkumar@vmware.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The page length for the 0xb2 VPD page is defined to be 4 bytes when no
provisioning descriptors are provided (DP=0).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add LBPRZ support to scsi_debug; i.e. read zeros for
unmapped blocks.
Rather than checking for unmapped blocks at
read time, this just zeroes them on the backing store
at unmap time so it behaves the same way.
This also adds a module parameter to disable it.
lbprz, "unmapped blocks return 0 on read (def=1)"
[jejb: fix whitespace errors]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If a ping or host event were to occur when memory is low
we do not want to use GFP_KERNEL, because the paths
sending them cannot block for data to be written. These
paths might be needed to recover write paths. Use GFP_NOIO
instead.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Casting pointer from native data type to other type is
endian-sensitive.
"iocmd->offset" is 64 bit but we use only first 32 bit.
It works in little-endian system but in big-endian system
it will break.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Defined error codes for ping completion status.
This patch take care of Mike Christie's commets
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The st tape driver recently added the MTWEOFI ioctl, which writes
a tape filemark (EOF), like the MTWEOF ioctl, except that MTWEOFI
returns immediately. This makes certain applications, like backup
software, run much more quickly on buffered tape drives.
Since legacy applications do not know about this new MTWEOFI ioctl,
this patch adds a new ioctl option that tells the st driver to return
immediately when writing an EOF (i.e. a filemark). This new flag
is much like the existing flag that tells the st driver to perform
writes (and certain other IOs) immediately, but this new flag only
applies to writing EOFs.
This new feature is controlled via the MTSETDRVBUFFER ioctl, using
the newly-defined MT_ST_NOWAIT_EOF flag.
Use of this new feature is displayed via the sysfs tape "options"
attribute.
The st documentation was updated to mention this new flag, as well
as the problems that can occur from using it.
Signed-off-by: Lee Duncan <lduncan@suse.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Used PCI configure space read to flush PCI function reset register write
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed system panic when extents enabled with large number of small blocks
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adapt comment and printk string after renaming sd_init_command to sd_prep_fn
Adapt comment and printk string after renaming sd_attach to sd_probe
Signed-off-by: Petr Uzel <petr.uzel@suse.cz>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for Universal Flash Storage(UFS)
host controllers. The UFS host controller driver
includes host controller initialization method.
The Initialization process involves following steps:
- Initiate UFS Host Controller initialization process by writing
to Host controller enable register
- Configure UFS Host controller registers with host memory space
datastructure offsets.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
- Enable required interrupts
- Configure interrupt aggregation
[jejb: fix warnings in 32 bit compile]
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Signed-off-by: Vinayak Holikatti <vinholikatti@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@linaro.org>
Reviewed-by: Vishak G <vishak.g@samsung.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin