Software must explicitely re-enable extended firmware tracing
after any ISP abort condition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only. If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).
The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a problem where sg is executing a ->nopage operation on a
compound page, it actually calls get_page() on the first page in the
compound rather than the page which is being mapped. The fix is to
select the correct page by indexing into the compound.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The subsystem check in the PAV code is incorrect, it enables PAV
per device instead of per subsystem.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
vt6420 has super-fragile SCR registers which can hang the whole
machine if accessed with the wrong timings. This patch makes sata_via
use SCR registers only during probing and with the same timings as
before (pre new EH), which is proven to work.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements force_pcs module parameter for ata_piix. If 1,
PCS is ignored, 2 honored. As there seem to be quite a few ICHs w/
impaired PCS, this option will be useful for cases where the default
setting doesn't work.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There have been a number of reports regarding some ICH5s failing to
detect devices since the PCS handling update. Analysis shows that
these problems are caused by bogus PCS values from those controllers.
Before the PCS update, the driver didn't honor PCS regs exactly and
probed them in many cases PCS reports no device. Now that PCS is
honored exactly, these hardware problems are visible.
This patch makes ICH5 ignore PCS.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some recent myri10ge firmwares support multicast filtering as well
as an extended mcp_irq_data structure (64 instead of 40 bytes).
The new command MXGEFW_CMD_SET_STATS_DMA_V2 is used to check
whether the firmware support those. mgp->fw_multicast_support
is defined accordingly.
When fw_multicast_support is set, some new multicast filtering
commands is passed to the board in myri10ge_set_multicast_list().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add msg_enable and use netif_msg_link to enable/disable reporting
of link status changes since some Ethernet switches seem to generate
a lot of status changes under some circumstances and some people
want to avoid useless flooding in the logs.
Also add a counter for link status changes to statistics.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
spectrum_cs: Fix the logic so we error when the device is *not* present!
This fixes firmware upload failures which prevent the driver from
working (the bug is also present in 2.6.17).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A change I made for 2.6.17 and another for 2.6.18 do not work on older
pcnet32 chips which I do not have access to. If the chip is a 79C970 or
79C965, do not try and suspend or check the link status.
I have tested with a 79C970A, 79C971, 79C972, 79C973, 79C975, 79C976,
and 79C978.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I am using a Xircom CEM33 pcmcia NIC which has occasional hardware problems.
If the netdev watchdog detects a transmit timeout, do_reset is called which
msleeps - this is illegal in atomic context.
This patch schedules the timeout handling as a workqueue item.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
while playing with gcc 4.1 -Wextra warnings, I came across this one:
drivers/net/3c515.c:1027: warning: comparison of unsigned expression >= 0 is always true
Since i is unsigned the >= 0 check in the for loop is always true,
so we might spin there forever unless the if condition triggers.
Since i is only used in this loop, this patch changes it to
an integer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes yet another sunsab problem, when console is set to anything
but the first port. The console framework calls sunsab_console_setup
for each port, and we end up setting up a console on a not yet
discovered port, which leads to an Oops. Instead, defer console setup
until the requested port is properly initialized. Tested on an E250
through an RSC console.
Reported by Daniel Smolik <marvin@mydatex.cz>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver's list of HCA firmware revisions to make sure people
running Sinai firmware older than 1.1.0 get a message suggesting a
firmware upgrade. Update the Arbel versions as well while we are at it.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Intersil firmware 1.7.4 (and possibly others) loses the antenna
selection settings when the port is reset.
Signed-off-by: David Acker <dacker@roinet.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug was introduced during the PCMCIA API conversion and broke
spectrum_cs completely.
Tracked down by Fredrik Tolf <fredrik@dolda2000.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced in commit 3d0f0fa0cb:
bounds checking is performed against period[32] while indexing delay[4].
Spotted by Coverity, CID 1376.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move out PCS handling from piix_sata_prereset() into
piix_sata_present_mask() and use it from newly implemented
piix_sata_softreset(). Class codes for devices which are indicated to
be absent by PCS are cleared to ATA_DEV_NONE. This fixes ghost device
problem reported on ICH6 and 7.
This patch moves PCS handling from prereset to softreset, which makes
two behavior changes.
* perform softreset even when PCS indicates no device
* PCS handling is repeated before retrying softresets due to reset
failures.
Both behavior changes are intended and more consistent with how other
drivers behave.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
One of my recent changes broke C101 carrier handling, this patch
fixes it. Also fixes an old TX underrun checking bug.
2.6.18 material. Please apply.
Thanks.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removes an unused function from the via-velocity-driver.
It doesn't make the binary smaller, but the source cleaner.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert the myri10ge driver to use netdev_alloc_skb instead of dev_alloc_skb,
which requires to propagate the net_device across several functions.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch should update the fs_enet infrastructure to utilize Phy Abstraction
Layer subsystem. Along with the above, there are apparent bugfixes, overhaul
and improvements.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc. information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
qeth: bhs must be disabled when accessing neighbour tables.
=================================
[ INFO: inconsistent lock state ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@axis.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool -g (show ring sizes) support to the Spidernet network driver.
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unclear how these bugs arrived, presumably from incorrect cleanup of
the 16-bit-only paths, but smc91x wouldn't build for OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It looks like broken BIOSes controlling Rhine chips will remain in use in
significant numbers; such systems fail to come up via PXE after they have
been put into D3 (power-saving) mode.
This patch adds a module option for disabling the call that puts the chip
to sleep.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Joerg Bashir <brak@archive.org>
Cc: Tim Phipps <tim@phipps-hutton.freeserve.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When booting using root-nfs, I'm seeing (independently) two lockdep dumps
in the smc91x driver. The patch below fixes both. Both dumps look like
real locking issues.
Nico - please review and ack if you think the patch is correct.
Dump 1:
Sending DHCP requests .
=================================
[ INFO: inconsistent lock state ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The poll_enable should be in init_registers before enabling interrupts, not
in tx_timeout. Thanks for spotting it Roger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Cc: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add NAPI support to the via-rhine driver so that it can handle higher
speeds and doesn't get overloaded by interrupts as easily.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x driver forgets to release the spinlock on spurious interrupts.
This little patch fixes it.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add netconsole support to dm9000 driver.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sparc32:
drivers/net/s2io.c:2636: warning: implicit declaration of function 'disable_irq'
drivers/net/s2io.c:2656: warning: implicit declaration of function 'enable_irq'
Cc: Ananda Raju <Ananda.Raju@neterion.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device. This patch provides driver for the device.
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/sundance.c:110: error: version causes a section type conflict
I don't understand this error. It's referred to from both __init and
__devinit code. With CONFIG_HOTPLUG=n, version[] is placed in .init.data and
is referred to from .init.text.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With CONFIG_HOTPLUG=n it won't compile:
distcc[25607] ERROR: compile drivers/net/fealnx.c on g5/64 failed
version[] is referred to from both __init code and from __devinit code, so
move it out of __init altogether.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With CONFIG_HOTPLUG=n it won't compile:
drivers/net/tulip/winbond-840.c:141: error: version causes a section type conflict
(For some reason it gets the same error if marked __initdata. Give up.)
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/seeq8005.o - Section mismatch: reference to .init.text:seeq8005_probe from .text between 'init_module' (at offset 0x106) and 'seeq8005_open'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/ni65.o - Section mismatch: reference to .init.text:ni65_probe from .text between 'init_module' (at offset 0x54a) and 'ni65_stop_start'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/wd.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xfd) and 'wd_open'
WARNING: drivers/net/wd.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x14b) and 'wd_open'
WARNING: drivers/net/wd.o - Section mismatch: reference to .init.data:wd_portlist from .text between 'init_module' (at offset 0x17f) and 'wd_open'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/tokenring/smctr.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x2ba0) and 'smctr_reset_adapter'
WARNING: drivers/net/tokenring/smctr.o - Section mismatch: reference to .init.text:smctr_probe from .text between 'init_module' (at offset 0x2bf4) and 'smctr_reset_adapter'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_mem_base from .text between 'ibmtr_probe1' (at offset 0x6e6) and 'ibmtr_probe_card'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_mem_base from .text between 'ibmtr_probe1' (at offset 0x74a) and 'ibmtr_probe_card'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_mem_base from .text between 'ibmtr_probe1' (at offset 0x7fd) and 'ibmtr_probe_card'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/ni52.o - Section mismatch: reference to .init.text:ni52_probe from .text between 'init_module' (at offset 0x997) and 'ni52_close'
WARNING: drivers/net/ni65.o - Section mismatch: reference to .init.text:ni65_probe from .text between 'init_module' (at offset 0x54a) and 'ni65_stop_start'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/lne390.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x100) and 'lne390_close'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/lance.o - Section mismatch: reference to .init.data:lance_portlist from .text between 'init_module' (at offset 0x8d3) and 'lance_purge_ring'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.data:cardname from .text between 'init_module' (at offset 0x6d2) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x6ef) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x702) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.data:cardname from .text between 'init_module' (at offset 0x70e) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x71d) and 'eth16i_multicast'
WARNING: drivers/net/eth16i.o - Section mismatch: reference to .init.data:cardname from .text between 'init_module' (at offset 0x729) and 'eth16i_multicast'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/es3210.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xdf) and 'es_close'
WARNING: drivers/net/es3210.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x100) and 'es_close'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/eexpress.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x6c3) and 'eexp_hw_lasttxstat'
WARNING: drivers/net/eexpress.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x74f) and 'eexp_hw_lasttxstat'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/eepro.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x284) and 'eepro_ethtool_get_drvinfo'
WARNING: drivers/net/eepro.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x2a7) and 'eepro_ethtool_get_drvinfo'
WARNING: drivers/net/eepro.o - Section mismatch: reference to .init.data:eepro_portlist from .text between 'init_module' (at offset 0x2b3) and 'eepro_ethtool_get_drvinfo'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/e2100.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xd9) and 'e21_reset_8390'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/at1700.o - Section mismatch: reference to .init.text:at1700_probe from .text between 'init_module' (at offset 0x75) and 'net_get_stats'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/cs89x0.o - Section mismatch: reference to .init.data:version from .text between 'init_module' (at offset 0x13d8) and 'net_get_stats'
WARNING: drivers/net/cs89x0.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x1634) and 'net_get_stats'
WARNING: drivers/net/cs89x0.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x1a1f) and 'net_get_stats'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/appletalk/cops.o - Section mismatch: reference to .init.text:cops_probe from .text between 'init_module' (at offset 0xae) and 'cops_rx'
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/ac3200.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0xf9) and 'ac_close_card'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/82596.o - Section mismatch: reference to .init.text:i82596_probe from .text between 'init_module' (at offset 0x141) and 'i596_add_cmd'
Also nail a couple of crazy inlines.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stall error handler if attempting resets/aborts while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Background:
Although the transport is using the scsi_timed_out functionality to
restart the timeout if the rport is blocked, if the timeout has already
fired before the block occurs, the eh handler still runs and can take
the device offline. Ultimately, this window cannot be resolved without
significant work in the error handler thread. Christoph noted the first
level of these issues when he noted the poor error response handling
by the error thread.
We found, under heavy load and error testing, that time window from when
the scsi_times_out() adds the io to the queue to when the scsi_error_handler
gets around to servicing it, can be in the several seconds range. In most
cases, these test conditions are highly unusual, but possible.
As a result, we're stalling the error handler in this race window so that
we can avoid the device_offline transitions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Misc Bug Fixes:
- Cap MBX_DOWN_LINK command timeout to 60 seconds
- Fix double free of ndlp object
- Don't free mbox structures on error. The completion handlers expect to do so.
- Clear host attention work items when going offline
- Fixed discovery issues in multi-initiator environments.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Leave all SRQ methods out of the device's uverbs_cmd_mask if the
device doesn't have SRQ support (because of ancient firmware) so that
we don't allow userspace to call the driver's create_srq method. This
fixes a userspace-triggerable oops caused by ib_uverbs_create_srq()
following the device's ->create_srq function pointer, which will be
NULL if the device doesn't support SRQs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PPP code contains two kmalloc()s followed by memset()s without
handling a possible memory allocation failure. (Suggested by Joe
Perches).
And furthermore, conversions from kmalloc+memset to kzalloc.
[akpm@osdl.org: fix error-path leak]
[akpm@osdl.org: cleanups]
[paulus@samba.org: don't add useless printk and cardmap_destroy calls]
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert dev_alloc_skb() to netdev_alloc_skb() and increase default
rx ring size to 255. The old ring size of 100 was too small.
Update version to 1.4.44.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a subtle race condition between bnx2_start_xmit() and bnx2_tx_int()
similar to the one in tg3 discovered by Herbert Xu:
CPU0 CPU1
bnx2_start_xmit()
if (tx_ring_full) {
tx_lock
bnx2_tx()
if (!netif_queue_stopped)
netif_stop_queue()
if (!tx_ring_full)
update_tx_ring
netif_wake_queue()
tx_unlock
}
Even though tx_ring is updated before the if statement in bnx2_tx_int() in
program order, it can be re-ordered by the CPU as shown above. This
scenario can cause the tx queue to be stopped forever if bnx2_tx_int() has
just freed up the entire tx_ring. The possibility of this happening
should be very rare though.
The following changes are made, very much identical to the tg3 fix:
1. Add memory barrier to fix the above race condition.
2. Eliminate the private tx_lock altogether and rely solely on
netif_tx_lock. This eliminates one spinlock in bnx2_start_xmit()
when the ring is full.
3. Because of 2, use netif_tx_lock in bnx2_tx_int() before calling
netif_wake_queue().
4. Add memory barrier to bnx2_tx_avail().
5. Add bp->tx_wake_thresh which is set to half the tx ring size.
6. Check for the full wake queue condition before getting
netif_tx_lock in tg3_tx(). This reduces the number of unnecessary
spinlocks when the tx ring is full in a steady-state condition.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While going through the code, I found out some memory leaks and potential
crashes in drivers/acpi/hotkey.c Please find the patch to fix them.
This patch does the following,
1. Fixes memory leaks in error paths of hotkey_write_config
2. Fixes freeing unallocated pointers in the error paths of hotkey_write_config
3. Uses a loop instead of linear searching for parsing the userspace
input in get_params
4. Uses array of char * instead of passing 4 pointer parameters
explicitly into the init_{poll_}hotkey_* static functions
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reduce writeback threshold by 1. We were instructing the hardware to
wait until the 17th descriptor which went over the cache line limit.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke.jan.h.kok@intel.com>
Disable aggressive clocking on esb2 with SERDES port as it causes
hardware problems.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allow NVM to setup LPLU for IGP2 and IGP3. Only IGP needs LPLU D3
disabled during init here.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Explicitly lock two more ethtool entry points completely instead
of the hardware reset only to prevent a race condition.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Remove pci ID 8086:1000 from the list fo supported devices. This device
has not functioned with the driver for very long (since v. 5.2.4!)
and we lack the resources to come with a substantial fix. There are only
few cards of this type out there.
Signed-off-by: Jeff Kirsher <Jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
MDIO/MDIO-X was broken due to a wrong errata. Removing the workaround
code fixes for affected NICs.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
After commit 12bbb2b7be, when SM LID
change or LID change MAD also has a client reregistration bit set,
only CLIENT_REREGISTER event is generated.
As a result, the sa_query module and the cache module don't update the
port information, and ULPs (e.g. IPoIB) stop working. This is the
regression we observe as compared to 2.6.17.
Rather than generate multiple events (which would have negative
performance impact), let us simply let cache and SA query respond to
reregister event in the same way as to LID and SM change events.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In some situations PAV alias devices on LPAR are not accessible.
The initialization procedure required to enable access to PAV alias
devices has to be performed per storage server subsystem and not
only once per storage server.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd_page_cache should return page addresses and therefore the
cache must be created with an alignment of PAGE_SIZE.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the build options for acpiphp so that it may build without being
dependent on the ACPI_DOCK option, but yet does not allow the option of
acpiphp being built-in when dock is built as a module.
This does not change the previous patch for ACPI_IBM_DOCK Kconfig.
For the following matrix of config options, I built an i386 kernel.
Dock acpiphp should it build? confirmed
y y y y
y n y y
y m y y
m y no - acpiphp should acpiphp was
convert to m converted to m
m n y y
m m y y
n y y y
n n y y
n m y y
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is to remove noisy useless message at boot. The message is a ton of
"ACPI Exception (acpi_memory-0492): AE_ERROR, handle is no memory device"
In my emulation, number of memory devices are not so many (only 6), but,
this messages are displayed 114 times.
It is showed by acpi_memory_register_notify_handler() which is called by
acpi_walk_namespace().
acpi_walk_namespace() parses all of ACPI's namespace and execute
acpi_memory_register_notify_handler(). So, it is called for all of the
device which is defined in namespace. If the parsing device is not memory,
acpi_memhotplug ignores it due to "no match" and will parse next device.
This is normal route, not an exception.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix acpi_ac/battery boot with acpi=off
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Three typos in drivers/char/watchdog/Kconfig...
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add basic Machine detection to imacfb and some Ducumentation bits for
imacfb.
Signed-off-by: Edgar Hucek <hostmaster@ed-soft.at>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the dependency on ieee80211.h from
the ray_cs driver. ray_cs only needs iw_handler.h.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add static to 2 internal functions. Thanks goes to Adrian Bunk, who found that.
Also made some modifications to the clear functions:
After a discussion on the mailing list, I implemented this code to
have on the one hand sufficient test in debug mode, but on the
other hand reduce the overhead for structure clearing to a
minimum.
A new macro ZD_MEMCLEAR is introduced, which produces code if
DEBUG is set. Locks are not set anymore for structure clearing,
but in debug mode, there is a verification, that the locks have
not been set.
Finally, removed a misleading comment regarding locking in the disconnect
path.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Longshine device is a ZD1211B and has a AL2230 RF. I tested it
successfully with no encryption and WEP.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices identify themselves as a virtual USB CDROM drive. The virtual CD
includes the windows driver. We aren't interested in this, so we eject the
virtual CDROM and then the real wireless device appears.
Patch fixed over the earlier version to not leak cmd, thanks to Michael Buesch
for spotting that.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211 chip 0586:3402 v4916 high 00-13-49 AL2230_RF pa0 ----
This device pops up after the virtual driver CD has been ejected.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed for my G220F, otherwise it fails to initialize after the
existing firmware upload routine.
The vendor driver actually does more than what I have done here: it
downloads the firmware + boot code, modifies it, and uploads it again
(really messy). I have not copied that part over, as my device can get
on its feet without it.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Wonka on IRC.
zd1211 chip 157e:3204 v4810 high 00-11-e0 AL7230B_RF pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by lyakh on IRC
zd1211 chip 1740:2000 v4721 high 00-02-6f AL7230B_RF pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for another Airoha RF which is present in some
ZD1211 adapters. This RF supports 802.11a as well as 802.11b/g, but 802.11a
connectivity is not yet supported by this driver.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch synchronizes our code to some recent vendor driver modifications.
A new PHY layout is supported, some values are tweaked, and the AL2230 is now
programmed over a new interface which is many times faster.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor driver resets the IFS value every time the channel changes,
to this one.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor driver chooses this value based on an ifndef ASIC,
and ASIC is never defined.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Please include the attached patch that adds support for a new PHY to the
sis900 driver. See also Bugzilla 6919.
Signed-off-by: Daniele Venzano <venza@brownhat.org>
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Enabling PXA DMA for the smc91x on the logicpd pxa270 produces
unacceptable interference with the TFT panel, so disable it. Also
delete the lpd270 versions of the SMC_{in,out}[bl]() macros, as they
aren't used, since the board only supports 16bit accesses.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In my quest to try and figure out why test 14 (control write) doesn't
work with my EZ-USB board, I noticed that sometimes testusb reported
no error even though the kernel log complained "byte 0 is 0 not 2" etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I write a patch for ipaq.c.
Would you like to add upstream tree ?
This patch enables a support of "SHARP W-ZERO3(WS004SH)" and "SHARP W-ZERO3[es](WS007SH)".
From: Norihiko Tomiyama <norihiko.tomiyama@ctc-g.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
appletouch uses urb->transfer_dma after having freed the urb, this shows
up only if the system is compiled with slab debugging. This patch fixes
it by reordering the free calls.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch has removed a unbalanced #endif from ohci-au1xxx.c .
Please apply before 2.6.18 release.
Error message was:
In file included from drivers/usb/host/ohci-hcd.c:909:
drivers/usb/host/ohci-au1xxx.c:113:2: #endif without #if
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as763) adds an unusual_devs entry for the A-VOX WSX-300ER MP3
player.
From: David Kuehling <dvdkhlng@gmx.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make pciehp build on powerpc
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When destroying a QP, mthca locks both the QP's send CQ and receive
CQ. However, the following scenario is perfectly valid:
QP_a: send_cq == CQ_x, recv_cq == CQ_y
QP_b: send_cq == CQ_y, recv_cq == CQ_x
The old mthca code simply locked send_cq and then recv_cq, which in
this case could lead to an AB-BA deadlock if QP_a and QP_b were
destroyed simultaneously.
We can fix this by changing the locking code to lock the CQ with the
lower CQ number first, which will create a consistent lock ordering.
Also, the second CQ is locked with spin_lock_nested() to tell lockdep
that we know what we're doing with the lock nesting.
This bug was found by lockdep.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The fence bit needs to be set in the doorbell too, not just the WQE.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The dasd function dasd_set_uid calls kzalloc while holding the
dasd_devmap_lock. Rearrange the code to do the memory allocation
outside the lock.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
On the 88E805X chipsets (used in laptops), the PHY was not getting powered
out of shutdown properly. The variable reg1 was getting reused incorrectly.
This is probably the cause of the bug.
http://bugzilla.kernel.org/show_bug.cgi?id=6471
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
Reading the Intel VSC and AHCI it seems like writing 0x302 is incorrect.
The only valid values are 4, 1 and 0. Writing 4 disables the
PHY.
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pdc_adma was overlooked and broken by the irq-pio patch:
Only HSM_ST_LAST interrupts should be delivered to this LLDD.
Adding ATA_FLAG_PIO_POLLING to pdc_adma fixes the problem (temporarily),
before we convert the irq handler of pdc_adma to handle all interrupts.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the IDE fix for Jmicron went in one piece went walking somewhere
(send log shows my end somehow). Without this sometimes you get an oops
on boot.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The request queue flush function of the dasd driver has to dequeue
the requests first and then call the end request function. Otherwise
a kernel bug in ll_rw_block.c might get triggered.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
SCSI EH locks door if sdev->locked is set. Sometimes door lock
command fails continuously (e.g. when medium is not present) and as
libata uses EH to acquire sense data, this easily creates a loop where
a failed lock door invokes EH and EH issues lock door on completion.
This patch clears sdev->locked on door lock failure to break this
loop. This problem has been spotted and diagnosed by Unicorn Chang
<uchang@tw.ibm.com>.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a sata debug print statement that still uses an old variable name.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dummy RDMA are always enabled on device startup since commit
9a71db721a (to work around buggy
PCIe chipsets which do not implement resending properly). But,
we also need to always re-enable them when resuming the device.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch uses the sundance_reset function everywhere a reset is done,
and adds a link to the archives of the original mailing list.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revised version of the forcedeth NAPI support.
This version is based against netdev-2.6#upstream
(after the MAC patches from Ayaz today).
Can't use nv_disable_hw_interrupts because NAPI only wants to
mask off receive irq's and leave the others alone.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch will correct the mac address and set a flag to indicate that
it is already corrected in case nv_probe is called again. For example,
when you use kexec to restart the kernel.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves the mac address setup/teardown to the
nv_probe/nv_remove functions. This fixes WOL wakeup since on nv_close we
would reverse the mac address. Also, bonding driver will reset address
after nv_close is called.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
'mdio_reset' has bad side effects that moves the phy_id.
DL10022-based cards work properly without 'mdio_reset'.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In bugzilla #6943, Maxim Britov reported:
"I can enable Logitech quickcam support in .config, but it want be compile.
I have to add into drivers/media/video/Makefile:
obj-$(CONFIG_USB_QUICKCAM_MESSENGER) += usbvideo/"
He's right, just enable that driver as module while disabling every other
driver that gets into that directory, nothing will get compiled.
This patch fixes the Makefile.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Without the LNA these tuners perform very poorly (read 'unwatchable') when
the signal is weak.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a wrong statement order the 'standard' module option didn't
work for 'G' model chips.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx25840_read4 assembled the bytes in the wrong order.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The compat_ioctl support of the pwc driver was dropped during the last update of the driver.
I suppose it was by mistake. If yes here is the patch to restore the support.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@looxix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a subtle race condition between tg3_start_xmit() and tg3_tx()
discovered by Herbert Xu <herbert@gondor.apana.org.au>:
CPU0 CPU1
tg3_start_xmit()
if (tx_ring_full) {
tx_lock
tg3_tx()
if (!netif_queue_stopped)
netif_stop_queue()
if (!tx_ring_full)
update_tx_ring
netif_wake_queue()
tx_unlock
}
Even though tx_ring is updated before the if statement in tg3_tx() in
program order, it can be re-ordered by the CPU as shown above. This
scenario can cause the tx queue to be stopped forever if tg3_tx() has
just freed up the entire tx_ring. The possibility of this happening
should be very rare though.
The following changes are made:
1. Add memory barrier to fix the above race condition.
2. Eliminate the private tx_lock altogether and rely solely on
netif_tx_lock. This eliminates one spinlock in tg3_start_xmit()
when the ring is full.
3. Because of 2, use netif_tx_lock in tg3_tx() before calling
netif_wake_queue().
4. Change TX_BUFFS_AVAIL to an inline function with a memory barrier.
Herbert and David suggested using the memory barrier instead of
volatile.
5. Check for the full wake queue condition before getting
netif_tx_lock in tg3_tx(). This reduces the number of unnecessary
spinlocks when the tx ring is full in a steady-state condition.
6. Update version to 3.65.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All caller of netdev_alloc_skb need to assign skb->dev shortly
afterwards. Move it into common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove system device class for xpram. It creates the directory hierarchy
under /sys/devices/system/xpram/xpram0. The xpram0 directory is empty and
it is always created while xpram1 and following devices are always missing,
independent if the devices exist or not. Since the xpram devices are
listed in /proc/partitions and /sys/block/ as slram<x> the system device
class for xpram is meaningless.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I/O on a CCW device may stall if a channel path to that device is
logicaly varied off/on. A user I/O interrupt can get misinterpreted
as interrupt for an internal path verification operation due to a
missing check and is therefore never reported to the device driver.
Correct check for pending interruptions before starting path
verification.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do a retry of read device characteristics / read configuration
data when a deferred condition code 1 is encountered in
ccw_device_wake_up().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Without this patch register_tape_dev() will always fail, but might
return a value that is not an error number. This will lead to accesses
to already freed memory areas...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Another misuse of the global 'io' variable instead of the local 'base'.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch corrects a problem in mptfc which can result in targets
being removed after executing an "lsiutil 99" reset of the fibre
channel ports.
The last rescan event was being processed before the setup reset work
due to an inappropriate optimization in the event processing logic.
Every rescan event is now queued for execution and the setup reset
work now executes in the proper sequence.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Based upon a conversation I had with LSI's fibre channel firmware guru,
this patch adds another condition under which the driver waits for the
firmware link initialization / target discovery to complete.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There were some confusion about base I/O variables in the wbsd driver.
Seems like things have been working on shear luck so far. The global 'io'
variable (used when manually configuring the resources) was used instead of
the local 'base' variable.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCSI folk forgot to fix up all the uses of 'buffer' before deleting
this struct member. Do it for them to rescue the resulting build
failures.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The hptiop just got merged with a horrible amount of really bad ioctl
code that is against the standards for new scsi drivers. This patch
backs it out (and fixes a small bug where scsi_add_host is called to
early). We can re-add proper APIs once we agree on them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
arch/ia64/hp/sim/simscsi.c
Stylistic differences in two separate fixes for buffer->request_buffer
problem.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fixes for zfcp's erp:
- trigger adapter reopen if do_QDIO fails
- avoid erp deadlock if registration of scsi target or remote port hang
- do not treat as error if exchange port data fails
- decrease timeout for target reset and aborts
- mark unit failed if slave_destroy is called
Additionally some code cleanup was done:
- made some functions void when retval is not of interest
- shortened initialization of zfcp's host_template
- corrected some comments
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve request handling. Use hash table to manage request IDs.
Signed-off-by: Volker Sameske <sameske@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
