fix the problem that did not set IRQF_TRIGGER_ flag.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for hardware configurations that don't match the
chip default register settings (e.g., 16-bit data bus, DACK and
DREQ pulled up instead of down, analog overcurrent mode).
These settings are passed in via the OF device tree. The PCI
interface still assumes the same default values.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
mark this array as const because it is read-only
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark the tables as const so that they end up in .rodata
section and don't cacheline share with things that get
written to.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes some performance bugs observed with some workloads
when unlinking EHCI queue header (QH) descriptors from the async ring
(control/bulk schedule).
The mechanism intended to defer unlinking an empty QH (so there is no
penalty in common cases where it's quickly reused) was not working as
intended. Sometimes the unlink was scheduled:
- too quickly ... which can be a *strong* negative effect, since
that QH becomes unavailable for immediate re-use;
- too slowly ... wasting DMA cycles, usually a minor issue except
for increased bus contention and power usage;
Plus there was an extreme case of "too slowly": a logical error in the
IAA watchdog-timer conversion meant that sometimes the unlink never
got scheduled.
The fix replaces a simple counter with a timestamp derived from the
controller's 8 KHz microframe counter, and adjusts the timer usage
for some issues associated with HZ being less than 8K.
(Based on a patch originally by Alan Stern, and good troubleshooting
from Leonid.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we do rmmod ohci_hcd while an application is doing something, the
following may happen:
- a control URB completes (in finish_urb) and the ohci's endpoint is
set into ED_UNLINK in ed_deschedule
- same URB is (re)submitted because of the open/close loop or other
such application behaviour
- rmmod sets the state to HC_STATE_QUESCING
- finish_unlinks happens at next SOF; normally it would set ed into
ED_IDLE and immediately call ed_schedule (since URB had extra TDs
queued), which sets it into ED_OPER. But the check in ed_schedule
makes it fail with -EAGAIN (which is ignored)
- from now on we have a dead URB stuck; it cannot even be unlinked
because the ed status is not ED_OPER, and thus start_ed_unlink is
not invoked.
This patch removes the check. In 2.6.25, all callers check for
__ACTIVE bit before invoking ed_schedule, which is more appropriate.
Alan Stern and David Brownell approved of this (cautiously).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As RMK pointed out, considering the fact that the _only_ platform with
a PXA and SA1111 is the Lubbock, and that SA1111 DMA doesn't work there,
(i.e. the SA1111 OHCI doesn't work there) the SA1111 OHCI driver should
really be made SA11x0 specific.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like usb_put_hcd was missing. Also, make an always-zero function
return void.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the following needlessly global functions static:
- enqueue_an_ATL_packet()
- enqueue_an_INT_packet()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_name() function instead.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This includes PXA work up to the SPI changes for the initial merge,
since e172274ccc depends on the SPI
tree being merged.
Conflicts:
arch/arm/configs/em_x270_defconfig
arch/arm/configs/xm_x270_defconfig
This reverts commit e872154921.
Andrey Borzenkov reports that it resulted in a totally hung machine for
him when loading the OHCI driver. Extensive netconsole capture with
SysRq output shows that modprobe gets stuck in ohci_hub_status_data()
when probing and enabling the OHCI controller, see for example
http://lkml.org/lkml/2008/7/5/236
for an analysis.
The problem appears to be an interrupt flood triggered by the commit
that gets reverted, and Andrey confirmed that the revert makes things
work for him again.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a problem with OHCI where canceling bulk or
interrupt URBs may lose track of the right data toggle. This
seems to be a longstanding bug, possibly dating back to the
Linux 2.4 kernel, which stayed hidden because
(a) about half the time the data toggle bit was correct;
(b) canceling such URBs is unusual; and
(c) the few drivers which cancel these URBs either
[1] do it only as part of shutting down, or
[2] have fault recovery logic, which recovers.
For those transfer types, the toggle is normally written back
into the ED when each TD is retired. But canceling bypasses
the mechanism used to retire TDs ... so on average, half the
time the toggle bit will be invalid after cancelation.
The fix is simple: the toggle state of any canceled TDs are
propagated back to the ED in the finish_unlinks function.
(Issue found by leonidv11@gmail.com ...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a regression in the EHCI driver's TIMER_IO_WATCHDOG
behavior. The patch "USB: EHCI: add separate IAA watchdog timer" changed
how that timer is handled, so that short timeouts on the remaining
timer (unfortunately, overloaded) would never be used.
This takes a more direct approach, reorganizing the code slightly to
be explicit about only the I/O watchdog role now being overridable.
It also replaces a now-obsolete comment describing older timer behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the SM501 and another platform driver, such as the SM501
then we end up defining PLATFORM_DRIVER twice. This patch
seperated the SM501 onto a seperate define of SM501_OHCI_DRIVER
so that it can be selected without overwriting the original
definition.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change omap USB code to use omap_read/write instead of __REG for multi-omap
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb@vger.kernel.org
Cc: i2c@lm-sensors.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
and include pxa2xx-regs.h as build fix since PSSR definitions
moved from pxa-regs.h into pxa2xx-regs.h.
Note: This change is temporary as pxa27x processor specific
code will be finally moved elsewhere (both drivers should
support pxa3xx, too).
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes the bogus "io mem 0x00000000" message printed
during driver init due to hcd->rsrc_start being assigned after
the call to usb_add_hcd().
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
R8A66597 is similar to SH7723 USB 2.0 Host/Function module.
In addition, the USB of SH7366 is compatible with SH7723.
It can support SH7723 USB host by changing Kconfig.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit fa38dfcc56.
It wasn't really a regression and David and Alan are still working
through the issues reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1099) fixes a performance regression in ehci-hcd. The
fundamental problem is that queue headers get removed from the
schedule too quickly, since the code checks for a counter advancing
rather than making an actual time-based check. The latency involved
in removing the queue header and then relinking it can severely
degrade certain kinds of workloads.
The patch replaces a simple counter with a timestamp derived from the
controller's uframe value. In addition, the delay for unlinking an
idle queue header is increased from 5 ms to 10 ms; since some
controllers (nVidia) have a latency of up to 1 ms for unlinking, this
reduces the relative impact from 20% to 10%.
Finally, a logical error left over from the IAA watchdog-timer
conversion is corrected. Now the driver will always either unlink an
idle queue header or set up a timer to unlink it later. The old code
would sometimes fail to do either.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Leonid <leonidv11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1098) changes the way ehci-hcd schedules its periodic
Iso transfers. That the current scheduling code is wrong is clear on
the face of it: Sometimes it returns -EL2NSYNC (meaning that an URB
couldn't be scheduled because it was submitted too late), but it does
this even when the URB_ISO_ASAP flag is set (meaning the URB should be
scheduled as soon as possible).
The new code properly implements as-soon-as-possible scheduling,
assigning the next unexpired slot as the URB's starting point. It
also is more careful about checking for Iso URB completion: It doesn't
bother to check for activity during frames that are already over,
and it allows for the possibility that some of the URB's packets may
have raced the hardware when they were submitted and so never got used
(the packet status is set to -EXDEV).
This fixes problems several people have experienced with USB video
applications.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1097) fixes a bug in the remote-wakeup handling in
ehci-hcd. The driver currently does not keep track of whether the
change-suspend feature is enabled for each port; the feature is
automatically reset the first time it is read. But recent changes to
the hub driver require that the feature be read at least twice in
order to work properly.
A bit-vector is added for storing the change-suspend feature values.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller. But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.
The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller. If it has, the
error message is suppressed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1095) cleans up the HCD glue and several of the EHCI
bus-glue files. The ehci->is_tdi_rh_tt flag is redundant, since it
means the same thing as the hcd->has_tt flag, so it is removed and the
other flag used in its place.
Some of the bus-glue files didn't get the relinquish_port method added
to their hc_driver structures. Although that routine currently
doesn't do anything for controllers with an integrated TT, in the
future it might. So the patch adds it where it is missing.
Lastly, some of the bus-glue files have erroneous entries for their
hc_driver's suspend and resume methods. These method pointers are
specific to PCI and shouldn't be used otherwise.
(The patch also includes an invisible whitespace fix.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Commit 7329e211b9 ("USB: root hubs don't
lie about their number of TTs") requires the various platform EHCI
glue modules to set ->has_tt if the root hub has a Transaction
Translator.
The Orion EHCI root hub does have a Transaction Translator, so set
->has_tt in ehci_orion_setup(). This fixes oopsing on plugging in a
low speed device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/isp1760-if.c:275: warning: 'ret' is used uninitialized in this function
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ohci-sm501.c:93:24: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3254:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3267:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3277:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3285:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3293:9: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format warnings in isp1760 (in linux-next):
next-20080430/drivers/usb/host/isp1760-hcd.c:994: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
next-20080430/drivers/usb/host/isp1760-hcd.c:1092: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sparc doesn't have some of the OF interfaces this driver
wants to use.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1084b) fixes the way uhci-hcd handles polling and
remote wakeups for its root hubs. When remote wakeup is disabled,
neither interrupts nor polling should be enabled during a root-hub
suspend. Likewise, if interrupts are enabled during suspend then
polling isn't needed.
Furthermore the EGSM (Enter Global Suspend Mode) bit shouldn't be set
in the Command register unless remote wakeup is enabled. Apparently
some controllers will issue a remote-wakeup interrupt whenever EGSM
is on, even if Resume-Detect interrupts are supposedly disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch (as1086) works around a bogus "uninitialized variable"
warning generated by some versions of GCC.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds HCD support for the Cypress c67x00 family of devices.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* endianness annotations
* endianness fixes
* missing get_unaligned/put_unaligned
It's pretty much all over the place, changes to different files are independent.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Serial-parts-Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1072) fixes some recently-introduced compile problems
that show up in ehci-hcd when CONFIG_PM is turned off.
PORT_WAKE_BITS needs to be defined always.
ehci_port_power() is called during initialization by all the
EHCI variants other than the PCI version, in which it is
"defined but not used". So add a call to it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simplify processing of completed qtds, and correct handling of short
reads, by removing two state variables:
- "qtd_status" wasn't needed. The current URB's status is either
OK (-EINPROGRESS) or some fault status. Once a fault appears,
the queue halts and any later QTDs are immediately removed, so
no temporary status is needed. (Or for typical short reads,
it's not treated as a fault, so no queue halt is needed.)
- "do_status" was erroneous. Because of how the queue is set up,
short control reads can (and should!) be treated like full size
reads, and cleaned up the usual way. The status stage will be
executed transparently, and usbcore handles the choice of whether
to report this status as unexected.
The "do_status" problem caused a rather perplexing timing-dependent
problem with usbtest case 10. Sometimes it would make the controller
skip a dozen transactions while (wrongly) trying to clean up after a
short transfer. Fortunately, removing a dcache contention issue made
this become trivial to reproduce (on one test rig), so enough clues
finally presented themselves ... I think this has been around for a
very long time, but was worsened by recent urb->status changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069b) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1068b) disables the RD interrupt flag when an OHCI root
hub is suspended with remote wakeup disabled. Although the spec
clearly states that this flag permits the controller to issue an
interrupt when a resume request from downstream is detected and not
when a local status change occurs, some controllers mistakenly use it
for both types of event.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting. The setting
is then saved in the do_remote_wakeup flag.
Later on, however, the device_may_wakeup() value can change because of
user activity. So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup(). This patch (as1076)
makes that change for root hubs in several places.
The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.
And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide better comments about qh_completions() and QTD handling.
That code can be *VERY* confusing, since it's evolved over a few
years to cope with both hardware races and silicon quirks.
Remove two unlikely() annotations that match the GCC defaults
(and are thus pointless); add an "else" to highlight code flow.
This patch doesn't change driver behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
R8A66597 is similar to SH7366 USB 2.0 Host/Function module. It can
support SH7366 USB host by changing several R8A66597 code.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the problem that enumeration of a USB device was slow.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver ignored the value of bInterval and revised the problem
that performed interrupt transfer.
ASIX USB Ethernet adapter comes to work with this host controller
by applying this patch.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch refactors some shutdown code so it can be shared between
ehci_stop() and ehci_shutdown().
This also fixes a couple potential bugs:
- ehci_shutdown() was not locking ehci->lock before halting the HC.
- ehci_shutdown() didn't disable the watchdog and IAA timers.
- ehci_stop() was resetting the host controller when it may have been
running, which the EHCI spec says "may result in undefined behavior".
ehci_stop() was calling port_power() to turn off the ports, which waited
20ms after applying the port change. The msleep was for the case where
the HC might take 20ms to turn the ports on; since we're shutting them
off, we can avoid the msleep and just use ehci_turn_off_ports().
ehci_stop() doesn't need to clear the intr_enable register or revert
ownership of the companion controllers to the BIOS, because the host
controller reset should have done that. There might be a buggy host
controller that doesn't follow the reset rules, but for now we assume
it's redundant code and remove it.
[ A subsequent patch will cancel the timers later ... this version
carries forward existing bugs where timers could get re-armed
after they're canceled. ]
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers in the ohci-hcd family should perform certain tasks whenever
their controller device is resumed. These include checking for loss
of power during suspend, turning on port power, and enabling interrupt
requests.
Until now these jobs have been carried out when the root hub is
resumed, not when the controller is. Many drivers work around the
resulting awkwardness by automatically resuming their root hub
whenever the controller is resumed. But this is wasteful and
unnecessary.
To simplify the situation, this patch (as1066) adds a new core
routine, ohci_finish_controller_resume(), which can be used by all the
OHCI-variant drivers. They can call the new routine instead of
resuming their root hubs. And ohci-pci.c can call it instead of using
its own special-purpose handler.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The .suspend and .resume method pointers in struct usb_hcd have not
been fully understood by host-controller driver writers. They are
meant for use with PCI controllers; other platform-specific drivers
generally should not refer to them.
To try and clarify matters, this patch (as1065) renames those methods
to .pci_suspend and .pci_resume. It eliminates corresponding dead code
and bogus references in the ohci-ssb and u132-hcd drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently EHCI root hubs enumerate with a bDeviceProtocol code
indicating that they possess a Transaction Translator. However the
vast majority of controllers do not; they rely on a companion
controller to handle full- and low-speed communications. This patch
(as1064) changes the root-hub device descriptor to match the actual
situation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1063) fixes a bug in the way ohci-hcd resumes its
controllers. It leaves the Master Interrupt Enable bit turned off.
If the root hub is resumed immediately this won't matter. But if the
root hub is suspended (say because no devices are plugged in), it won't
ever wake up by itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
platform_get_resource() may return null, so although it seems it will never
do so here unless there's a bug elsewhere, it does no harm to be defensive
and test.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was converting a semaphore in this file to a mutex when I noticed that
this file has some fairly rampant style problems. Practically every line
has spaces instead of tabs .. Once I cleared that up, checkpatch.pl showed
a number of other problem.. I think this file might be a good one to review
for new style checks that could be added..
Below are the only two remaining which I didn't remove.
#5083: FILE: drivers/usb/host/u132-hcd.c:2907:
+ error:
WARNING: labels should not be indented
#5087: FILE: drivers/usb/host/u132-hcd.c:2911:
+ stall:
These labels are actually inside a switch statement, and they are right
under "default:". "default:" appears to be exempt and these other label
should be too, or default shouldn't be exempt.
I also deleted a few lines due to single statements inside { } ,
if (is_error()) {
return;
}
becomes,
if (is_error())
return;
with one line deleted.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to David Brownell, this feature doesn't require an
experimental designation any longer.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some EHCI fault paths with large control transfers aren't coded. Avoid
problems by rejecting transfers that may need two qTDs (16+ KB). This is
mostly paranoia; even 4 KB transfers are rare, and most HCDs use lower
limits (so it's unlikely anyone would ever try such a thing).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
power.power_state is scheduled for removal. This patch (as1053)
removes all uses of that field from drivers/usb. Almost all of them
were write-only, the most significant exceptions being sl811-hcd.c and
u132-hcd.c.
Part of this patch was written by Pavel Machek.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was pointed out that we found and fixed the cause of the "bogus"
fatal IRQ reports some time ago ... this patch removes the code
which was working around that bug ("status" got clobbered), and a
comment which needlessly confused folk reading this code.
This also includes a minor cleanup to the code which fixed that bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor the EHCI "if (handshake()) state = HC_STATE_HALT" idiom,
which appears 4 times, by replacing it with calls to a new function
called handshake_on_error_set_halt(). Saves a few bytes too.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various minor fixes to some SOC bus glue for EHCI:
- Remove a bogus copyright (by "me"!) which someone added to the FSL
driver, and an irrelevant comment.
- Un-break MODULE_ALIAS() directives after platform_bus hotplugging
acquired a backwards-incompatible change. (Which didn't fix ANY
of the in-tree drivers it prevented from hotplugging -- sigh.)
- Remove some bogus assignments of platform_bus_type; that's done by
the platform_bus code.
- Add some FIXMEs for drivers with that pointless two-level idiom for
probe() and remove() routines. ("Obfuscation" is a non-goal.)
That should help avoid future bus glue which copies that idiom.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This teaches EHCI how to to work around bugs in certain high speed
devices, by accomodating "bulk" packets that exceed the 512 byte
constant value required by the USB 2.0 specification. (Have a
look at section 5.8.3, paragraphs 1 and 3.)
It also makes the descriptor parsing code warn when it encounters
such bugs. (We've had reports of maybe two or three such devices,
all pretty recent.)
Such devices are nonconformant. The proper fix is have the vendors
of those devices do the simple, obvious, and correct thing ... which
will let them be used with USB hosts that don't have workarounds for
this particular vendor bug. But unless/until they do, we can at least
have one of the high speed HCDs work with such buggy devices.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This limits how long the OHCI port reset loop waits for the hardware
to do its job, if the controller either (a) dies, or (b) can't finish
the reset. Such limits are always a good idea.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanups to the EHCI code: revision history is what source
code repositories should have. Switch to a more standard way to
kick in verbose debugging -- don't be EHCI-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1047) removes the USB_PERSIST Kconfig option, enabling
it permanently. It also prevents the power/persist attribute from
being created for hub devices; there's no point in having it since
USB-PERSIST is always turned on for hubs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1044) causes EHCI port handover for non-high-speed
devices to occur during every root-hub resume, not just in cases where
the controller lost power or was reset. This is necessary because:
When some machines go into suspend, they remove power from
on-board USB devices while retaining suspend current for USB
controllers.
The user might well unplug a USB device while the system is
suspended and then plug it back in before resuming.
A corresponding change is made to the core resume routine; now
high-speed root hubs will always be resumed when the system wakes up,
even if they were suspended before the system went to sleep. If this
weren't done then EHCI port handover wouldn't work, since it is called
when the EHCI root hub is resumed.
Finally, a comment is added to the hub driver explaining the khubd has
to be freezable; if it weren't frozen then it could interfere with
port handover.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable USB HCDs,
to allow re-enable auto loading.
[dbrownell@users.sourceforge.net: more drivers; registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Code inspection discovered in 2 places timers were being incorrectly setup
using round_jiffies_relative(HZ). The timer would then fire at time (0 <= T <
HZ).
Fix them to use round_jiffies(jiffies + HZ);
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, suggested by Alan Stern, fixes the hung USB issues
on my notebook from suspend/resume cycles.
It does so by eliminating some confusion about the internal state
machine associated with unlinking from the EHCI async schedule ring,
which caused a recent regression:
http://bugzilla.kernel.org/show_bug.cgi?id=10345
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make it possible to pass mbus_dram_target_info to the ehci-orion
driver via the platform data, make the ehci-orion driver program
the window registers based on this data if it is passed in, and
make the Orion platform setup code use this method instead of
programming the EHCI mbus window registers by hand.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The VIA VT6212 defaults to only waiting 1us between passes over EHCI's
async ring, which hammers PCI badly ... and by preventing other devices
from accessing the bus, causes problems like drops in IDE throughput,
a problem that's been bugging users of those chips for several years.
A (partial) datasheet for this chip eventually turned up, letting us
see how to make it use a VIA-specific register to switch over to the
the normal 10us value instead, as suggested by the EHCI specification
Solution noted by Lev A. Melnikovsky.
It's not clear whether this register exists on other VIA chips; we
know that it's ineffective on the vt8235. So this patch only applies
to chips that seem to be incarnations of the (discrete) vt6212.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Lev A. Melnikovsky <melnikovsky@mail.ru>
Tested-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent EHCI driver update to split the IAA watchdog timer out from
the other timers made several things work better, but not everything;
and it created a couple new issues in bugzilla. Ergo this patch:
- Handle a should-be-rare SMP race between the watchdog firing
and (very late) IAA interrupts;
- Remove a shouldn't-have-been-added WARN_ON() test;
- Guard against one observed OOPS;
- If this watchdog fires during clean HC shutdown, it should act
as a NOP instead of interfering with the shutdown sequence;
- Guard against silicon errata hypothesized by some vendors:
* IAA status latch broken, but IAAD cleared OK;
* IAAD wasn't cleared when IAA status got reported;
The WARN_ON is in bugzilla as 10168; the OOPS as 10078; these are
both regressions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the buffering of the status register.
USB core behavior has changed a bit and this buffering was not refreshed
at the right time. The core got buffered old value of HCRHPORT and it
did not detect any devices on boot.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Acked by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: ehci: Fixes completion for multi-qtd URB the short read case
When use of urb->status in the EHCI driver was reworked last August
(commit 14c04c0f88), a bug was inserted
in the handling of early completion for bulk transactions that need
more than one qTD (e.g. more than 20KB in one URB).
This patch resolves that problem by ensuring that the early completion
status is preserved until the URB is handed back to its submitter,
instead of resetting it after each qTD.
Signed-off-by: Misha Zhilin <misha@epiphan.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the following compile error caused by commit
3a2d5b7001 ("PM: Introduce
PM_EVENT_HIBERNATE callback state")
CC [M] drivers/usb/host/u132-hcd.o
drivers/usb/host/u132-hcd.c: In function ‘u132_suspend’:
drivers/usb/host/u132-hcd.c:3224: error: expected expression before ‘int’
drivers/usb/host/u132-hcd.c:3225: error: ‘ports’ undeclared (first use in this function)
...
Signed-off-by: Mirco Tischler <mt-ml@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.
But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.
For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate. Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.
These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts USB_EHCI_FSL config option into the verbose
bool, so we'll able to select it for other freescale processors
with built-in EHCI controller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, this setup:
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_HCD_PPC_OF=y
Will fail to build:
CC drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-hcd.c:1018:2: error: #error "missing bus glue for ehci-hcd"
make[3]: *** [drivers/usb/host/ehci-hcd.o] Error 1
ehci-hcd.c actually contains OF_PLATFORM_DRIVER glue, so error is bogus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous fix for a "sparse" warning in ehci_urb_dequeue() was
incorrect. After rescheduling interrupt transfers it returned the
URB's completion status, not status for the dequeue operation itself.
This patch resolves that issue, cleans up the code in the reschedule
path, and shrinks the object code by a dozen bytes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The config symbol for mpc834x processors is CONFIG_PPC_MPC834x,
not CONFIG_MPC834x.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
Convert quirk printks to dev_printk().
I made the MSI disable messages a little more consistent:
- always use "disabled", not "deactivated"
- specify "device MSI disabled" or "subordinate MSI disabled" when
disabling MSI for only a specific device or subordinate bus
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While most isochronous endpoints have short polling intervals, the
EHCI driver won't necessarily handle larger ones correctly.
This patch switches to use a "u16" to represent those periods, not
a u8, since it can always work: the largest expressible period
is 2^15 units ... not the previous too-short limit of 128 frames
(full or low speeds) or microframes (high speed, 32 frames).
This bug is essentially theoretical, since the few ISO endpoints
I've seen which don't use one transfer per frame are high speed
ones using more than that (including high bandwidth, 24 KB/msec).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the "EHCI ports reset forever" problems may be explained by
code paths which wrongly flagged resets as complete. This removes
two such paths; the ehci_hub_status_data() path should be the only one
to have an effect, since it was already properly flagged on the other
path. (Issue noted by Minhyoung Kim <a9a9@lge.com>.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: ohci-sm501 driver V2
This patch adds sm501 ohci support. It's all very straightforward with the
exception of dma_declare_coherent_memory() and HCD_LOCAL_MEM. Together they
are used to ensure that usb data is allocated using dma_alloc_coherent(),
and that only valid dma memory is used to allocate from. This driver is
a platform device, and the mfd driver sm501.c is already creating one
usb host controller instance per sm501.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1031) adds a short delay to the bus-suspend routine in
ehci-hcd. Without it some devices disconnect when they should
suspend.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1030b) moves a del_timer_sync() call outside the scope of a
spinlock, where it could cause a deadlock, and adds a new
del_timer_sync() call for the new IAA watchdog timer (it was omitted
by mistake).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This has some bugfixes for the EHCI driver's ISO transfer scanning
logic. It was leaving ITDs and SITDs on the schedule too long, for
a few different reasons, which caused trouble.
(a) Look at all microframes for high speed transfers, not just
the ones we expect to have finished. This way transfers
ending mid-frame will complete without needing another IRQ.
This also minimizes bogus scheduling underruns (e.g. EL2NSYNC).
(b) When we encounter an ISO transfer (either speed, but this
hits mostly at full speed) that's not yet been completed,
immediately stop scanning; we've caught up to the hardware,
no matter what other indications might say.
(c) Always clean up ITDs (for high speed transfers) when the HC
is no longer running.
I'm not sure whether the last one has been observed before, but both
the others have been reported with "real world" audio and video code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Small updates to the EHCI driver's ISO support:
- Get rid of the Kconfig option for full speed ISO. It may
not be perfect yet, but it hasn't appeared to be dangerous
and pretty much every configuration wants it.
- Instead of two places to disable an empty periodic schedule
after an ISO transfer completes, just have one.
- After the periodic schedule is disabled, we can short-circuit
the schedule scan ... it can't possibly have more work to do.
Assuming a typical config with split iso enabled, the only change
in behavior should be almost unobservable: quicker termination
of periodic scans when the schedule gets emptied.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the EHCI driver, itd->usecs[8] is used in periodic_usecs(), indexed by
uframe. For an ITD's unused uframes it is 0, else it contains the same
value as itd->stream->usecs. To check if an ITD's uframe is used, we can
instead test itd->hw_transaction[uframe]: if used, it will be nonzero no
matter what endianess is used.
This patch replaces those two uses, eliminates itd->usecs[], and saves
eight bytes from each ITD.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds device-tree-aware ehci-ppc-of driver.
The code is based on the ehci-ppc-soc driver by
Stefan Roese <sr@denx.de>.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the ohci-at91 bus glue to start understanding about the per-port
power switch GPIOs it's given (on the sam9263-ek and potentially other
boards). For the moment this just claims them and forces them active
(assuming active-low power enables) whenever the HCD is loaded.
The assumption is still that board setup configures the GPIOs. Using
gpio_request() tracks actual usage and guards against conflict.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a missing dependency which goofs up the xconfig display.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kernel bugzilla entry #9569 reports a potential OOPS in some code
supporting the integrated root hub TT support used on ARC/TDI
derived cores. (This seems to have been a longstanding issue.)
This patch cleans up usage of urb->dev->tt to avoid that potential
oops and also fixes some overly long lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some glue bits for the on-chip USB host controller in the Marvell Orion
family of ARM SoCs, which is basically EHCI compatible.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix warning:
drivers/usb/host/ehci-hcd.c:832:8: warning: symbol 'status' shadows an earlier one
drivers/usb/host/ehci-hcd.c:790:71: originally declared here
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a workaround for an issue reported with ISO transfers
on some EHCI controllers, most recently with VIA KT800 and PS3
EHCI silicon.
The issue is that the silicon doesn't necessarily seem to be done
using ISO DMA descriptors (itd, sitd) when it marks them inactive.
(One theory is that the ill-defined mechanism where hardware caches
periodic transfer descriptors isn't invalidating their state...)
With such silicon, quick re-use of those descriptors makes trouble.
Waiting until the next frame seems to be a sufficient workaround.
This patch ensures that the relevant descriptors aren't available
for immediate re-use. It does so by not recycling them until after
issuing the completion callback which would reuse them by enqueueing
an URB and thus (re)allocating ISO DMA descriptors.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Masashi Kimoto <Masashi_Kimoto@hq.scei.sony.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1028) was mostly written by David Brownell; I made only
a few changes (extra log info and a small bug fix -- which might
account for why David's version had to be reverted). It adds a new
watchdog timer to the ehci-hcd driver to be used exclusively for
detecting lost or missing IAA notifications.
Previously a shared timer had been used, which may have led to some
problems as reported by Christian Hoffmann.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OHCI driver's IRQ handler, while processing a WDH interrupt, masks
and unmasks it. I believe this is both broken (the write may still be
posted during the donelist processing it's trying to safeguard) and
useless as this IRQ may not be reissued until it's acked (unless this
legacy code is an uncommented workaround for some chip erratum).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch hands over the port to the companion when the
hub_port_connect_change fails.
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Continue is not needed at the bottom of a loop.
The semantic patch implementing this change is as follows:
@@
@@
for (...;...;...) {
...
if (...) {
...
- continue;
}
}
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert from class_device to device for drivers/usb/core.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:
http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html
This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix. The drivers will still bind against
the older names also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.
This mechanism can't be used on some controllers. Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.
This patch removes the optimisation and makes the code clearer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Host controller IRQs are supposed to be serviced with interrupts
disabled. This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it. It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().
This fixes Bugzilla #9335.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A recent patch added software synchronization during EHCI startup,
so ports aren't switched away from the companion controllers after
resets have started. This patch adds a short delay letting hardware
finish that port switching before any new resets begin ... so both
ends of that hardware race window are closed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dave Miller <davem@davemloft.net>
Cc: Dely Sy <dely.l.sy@intel.com>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a bug introduced by
commit b22817b3c8.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove various newly-introduced compiler warnings for OHCI.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix ssb_ohci_probe() build bug:
drivers/built-in.o: In function `ssb_ohci_probe':
ohci-hcd.c:(.text+0xbff39): undefined reference to `ssb_device_enable'
ohci-hcd.c:(.text+0xbff6f): undefined reference to `ssb_admatch_base'
ohci-hcd.c:(.text+0xbff8b): undefined reference to `ssb_admatch_size'
ohci-hcd.c:(.text+0xbffe5): undefined reference to `ssb_device_disable'
[...]
the reason was that this Kconfig combination was allowed:
CONFIG_SSB=m
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_OHCI_HCD_SSB=y
the fix is to require a modular USB_OHCI_HCD build when SSB is modular.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1003) changes uhci-hcd to treat the URB_ISO_ASAP flag
the same as other host controller drivers, namely, to schedule an Iso
URB for the first available time slot that hasn't already expired.
URBs in which the flag isn't set will be scheduled for the first slot
following the last URB, even if it has expired.
This fixes a problem reported by Martin Bachem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ohci_bus_{suspend,resume} exists only if we have CONFIG_PM; do the same
thing as other subdrivers...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as999) fixes a problem that sometimes shows up when host
controller driver modules are loaded in the wrong order. If ehci-hcd
happens to initialize an EHCI controller while the companion OHCI or
UHCI controller is in the middle of a port reset, the reset can fail
and the companion may get very confused. The patch adds an
rw-semaphore and uses it to keep EHCI initialization and port resets
mutually exclusive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: David Miller <davem@davemloft.net>
Cc: Dely L Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds SSB bus glue for the USB OHCI HCD.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup: references to two PM routines (and HCD entry points)
that no longer exist are swapped with their replacements.
Evidently au1xxx and ppc-soc EHCI support doesn't get compiled
with power management very much, or these build bugs would have
been patched long ago.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add OHCI big endian frame_no quirk. The frame_no value stored in the
HCCA is a 16 bit field at a specific offset, but since not all CPUs can
do 16-bit memory accesses it's used as a 32 bit field. And that's why
big-endian OHCI must shift 16 bits ... unless the spec is not followed.
Currently there's one MPC52xx platform that doesn't need the shift. This
patch adds a new "big endian frame_no" quirk to control that at runtime.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed the problem that accessed register of this controller after
having called iounmap().
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed the problem that does not work in the big endian machine.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed the problem that does not work in the case of bRequest = 0x05 in
Class or Vendor Request.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ELAN U132 Host Controller Driver uses the semaphore sw_lock as
mutex. Use the mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as979) removes the last vestiges of urb->status from the
host controller drivers and the root-hub emulator. Now the field
doesn't get set until just before the URB's completion routine is
called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as977) reorganizes the way r8a66597-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
Parts of this patch were written by Yoshihiro Shimoda.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as976) reorganizes the way sl811-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
The patch also improves the handling of faults during the status stage
of a control transfer, since it no longer needs to retain the error
information from the earlier stages.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as975) reorganizes the way ohci-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as974) reorganizes the way ehci-hcd sets urb->status. It
now keeps the information in a local variable until the last moment.
The patch also simplifies the handling of -EREMOTEIO, since the only
use of that code is to set the do_status flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as972) changes ohci-hcd so that after an error occurs, the
remaining TDs for the URB will be skipped over entirely instead of
going through the donelist. This enables the driver to give back the
URB as soon as the error is detected, avoiding the need to store the
error status in urb->status.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as970) adds a new urb->unlinked field, which is used to
store the status of unlinked URBs since we can't use urb->status for
that purpose any more. To help simplify the HCDs, usbcore will check
urb->unlinked before calling the completion handler; if the value is
set it will automatically override the status reported by the HCD.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as969) continues the ongoing changes to the way HCDs
report URB statuses. The programming interface has been simplified by
making usbcore responsible for clearing urb->hcpriv and for setting
-EREMOTEIO status when an URB with the URB_SHORT_NOT_OK flag ends up
as a short transfer.
By moving the work out of the HCDs, this removes a fair amount of
repeated code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (968) changes the way uhci-hcd reports status for
Isochronous URBs. Until now urb->status has been set to the last
detected error code. But other HCDs don't do this; they leave the
status set to 0 and report errors only in the individual iso packet
descriptors. So this patch removes the extra computation and makes
uhci-hcd behave like the others.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as967) makes a few relatively minor changes to the
r8a66597 driver:
finish_request() does nothing but call done(), so merge the
two routines.
Detect and report -EOVERFLOW errors.
Fix the calculation that checks for short packets.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is not necessary to powerdown the ports on ehci_pci_reinit() when the
chip reset already did that. Removing this saves 20ms during restart
after poweroff paths (which OLPC uses a lot).
To ensure driver startup then behaves consistently, force a reset during
driver startup. (Not doing this was an accident of some previous changes
to the init sequence.)
Make the corresponding change in the PS3 support. It's not clear what
ehci-fsl should do here; it has similar code to the PS3.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <rvinson@mvista.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as962) cleans up some code I forgot to remove earlier in
the isp116x and sl811 HCDs. There is no longer any need to check for
unlink-during-submit; it can't happen since the endpoint queues are
now under the protection of the HCD-private spinlock.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as954) implements a suggestion of David Brownell's. Now
the host controller drivers are responsible for linking and unlinking
URBs to/from their endpoint queues. This eliminates the possiblity of
strange situations where usbcore thinks an URB is linked but the HCD
thinks it isn't. It also means HCDs no longer have to check for URBs
being dequeued before they were fully enqueued.
In addition to the core changes, this requires changing every host
controller driver and the root-hub URB handler. For the most part the
required changes are fairly small; drivers have to call
usb_hcd_link_urb_to_ep() in their urb_enqueue method,
usb_hcd_check_unlink_urb() in their urb_dequeue method, and
usb_hcd_unlink_urb_from_ep() before giving URBs back. A few HCDs make
matters more complicated by the way they split up the flow of control.
In addition some method interfaces get changed. The endpoint argument
for urb_enqueue is now redundant so it is removed. The unlink status
is required by usb_hcd_check_unlink_urb(), so it has been added to
urb_dequeue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ZF Micro OHCI controller exhibits unexpected behavior that seems to be
related to high load. Under certain conditions, the controller will
complete a TD, remove it from the endpoint's queue, and fail to add it to
the donelist. This causes the endpoint to appear to stop responding. Worse,
if the device is removed while in that state, OHCI will hang while waiting
for the orphaned TD to complete. The situation is not recoverable without
rebooting.
This fix enhances the scope of the existing OHCI_QUIRK_ZFMICRO flag:
1. A watchdog routine periodically scans the OHCI structures to check
for orphaned TDs. In these cases the TD is taken back from the
controller and completed normally.
2. If a device is removed while the endpoint is hung but before the
watchdog catches the situation, any outstanding TDs are taken back
from the controller in the 'sanitize' phase.
The ohci-hcd driver used to print "INTR_SF lossage" in this situation;
this changes it to the universally accurate "ED unlink timeout". Other
instances of this message presumably have different root causes.
Both this Compaq quirk and a NEC quirk are now properly compiled out for
non-PCI builds of this driver.
Signed-off-by: Mike Nuss <mike@terascala.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up duplicate includes in
drivers/usb/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Three main sets of changes:
1) dmi_get_system_info() return value should have been marked const,
since callers should not be changing that data.
2) const-ify DMI internals, since DMI firmware tables should,
whenever possible, be marked const to ensure we never ever write to
that data area.
3) const-ify DMI API, to enable marking tables const where possible
in low-level drivers.
And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.
The bulk of the changes are #2 and #3, which are interrelated. #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Correctly initialize the on-chip EHCI controller on the AMCC PPC440EPx.
Fix "USB 0.0" initialization message, and properly put the controller
into a known state before starting it.
Add "FIXME" comment to the au1xxx bus glue which is doing the same wrong
thing here. (Who maintains that, now that AMD sold off Alchemy?) Remove
some false copyright attributions which were somehow placed in the au1xxx
bus glue then copied into ppc-soc.
Signed-off-by: Mike Nuss <mike@terascala.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: K.Boge <karsten.boge@amd.com>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some versions of GCC recently grew annoying warnings about constants.
This gets rid of that warning from the OHCI driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently when registration fails we're left with a stray reference to
release_mem_region(), this leads to the following case:
r8a66597_hcd r8a66597_hcd: irq 13, io base 0x18040000
drivers/usb/host/r8a66597-hcd.c: register access fail.
r8a66597_hcd r8a66597_hcd: startup error -6
r8a66597_hcd r8a66597_hcd: USB bus 1 deregistered
drivers/usb/host/r8a66597-hcd.c: Failed to add hcd
Trying to free nonexistent resource <0000000018040000-0000000018040000>
This fixes it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed this warning with CONFING_PM=n
...
drivers/usb/host/u132-hcd.c:1525: warning: 'port_power' defined but not used
...
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 196705c9bb. It was
reported to cause a regression by Daniel Exner, and Arjan van de Ven
points out that we actually already have infrastructure in place for
setting limits on acceptable DMA latency that would be the much more
correct fix for the problem with some Broadcom EHCI controllers.
Fixed up trivial conflicts due to the changes to support big-endian host
controller descriptors in drivers/usb/host/{ehci-sched.c,ehci.h}.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch incorporates some updates. Updates include:
- Fix the problem that control transfer might fail
- Change from GFP_KERNEL to GFP_ATOMIC
- Clean up some coding style issue
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It has recently been pointed out that short control transfers should
have a status stage, even if they generate an error because
URB_SHORT_NOT_OK was set. This patch (as935) changes uhci-hcd to
enable the status stage when this happens.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as931b), adapted from a patch by Olav Kongas, makes a small
set of conservative changes to the isp116x-hcd driver in preparation
for the removal of urb->status.
finish_request() is moved up in the source and is called
as soon as the URB is known to have completed, rather than
after all the active endpoints have been scanned.
The status of a completed URB is kept in a local variable
and copied to urb->status only when the URB is about to be
given back.
-EREMOTEIO error status for control transfers is set after
the status stage rather than when the short packet arrives.
Some unnecessary uses of urb->lock are removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ELAN U132 adapter driver uses the semaphore u132_module_lock
as mutex. Use the mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unnecessary cast of return value of kzalloc() in
usb/host/ohci-pnx4008.c
Signed-off-by: Suresh Jayaraman <sjayaraman@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Root hubs can't be resumed if their parent controller device is still
suspended. This patch (as925) adds a check for that condition in
hcd_bus_resume() and prevents it from being treated as a fatal
controller failure.
ehci-hcd is updated to add the corresponding test. Unnecessary
debugging messages are removed from uhci-hcd and dummy-hcd. The
error return code from dummy-hcd is changed to -ESHUTDOWN, the same as
the others. ohci-hcd doesn't need any changes.
Suspend handling in the non-PCI host drivers is somewhat hit-and-miss.
This patch shouldn't have any effect on them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the USB Specification Revision 2.0 chapter 11.12.5
a hub experiencing an over-current condition must place all
affected ports in the powered-off state. It seems that some root
hubs need port power to be cycled by software in order to get back
to normal functionality after an over-current condition ... like
the EHCI implementation on an MPC8343E.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB HCD glue updates to reflect the new PS3 unifed device support.
- Fixed remove() routine.
- Added shutdown() routine.
- Added request_mem_region() call.
- Fixed MODULE_ALIAS().
- Made a proper fix for the hack done to support muti-platform in commit
48fda45120.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a silicon bug in some NEC OHCI chips. The bug appears
at random times and is very, very difficult to reproduce. Without the
following patch, Linux would shut the chip and its associated devices
down. In Apple PowerBooks this leads to an unusable keyboard and mouse
(SSH still working). The idea of restarting the chip is taken from
public Darwin code.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the endianness select for transfer buffers in EHCI
controllers that have Transaction Translator built in the hub. Also I
cleaned it up to make rid of magic numbers.
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Cc: <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Substitute USB instances of __attribute__ ((unused)) functions with the
newly introduced __maybe_unused.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For MPC831x support, change the ehci-fsl driver to preserve
bits set in platform code. Add a common CONFIG_USB_EHCI_FSL
to indicate presence of Freescale EHCI SOC. Add FSL_USB2_DR_OTG
operating mode support, thus both host and device can work for the
mini-ab receptacle. Note: this doesn't enable OTG protocol
support.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now select the big-endian configuration options
CONFIG_USB_EHCI_BIG_ENDIAN_MMIO and CONFIG_USB_EHCI_BIG_ENDIAN_DESC in
the usb host Kconfig file and not in the platform Kconfig files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the AMCC 440EPx EHCI controller whose
in-memory data structures and the registers are represented in big-
endian format.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as895) fixes up a loose end in the port-handover code for
the USB-Persist facility. A special case occurs when a high-speed
device is attached to a port which the user has designated to run at
full-speed only; the port must be disabled before the handover can
take place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss
of VBUS power during suspend. In order for the USB-persist facility
to work correctly, it is necessary for low- and full-speed devices
attached to a high-speed port to be handed back to the companion
controller during resume processing.
This entails three changes: adding code to ehci-hcd to perform the
handover, removing code from ohci-hcd to turn off ports during
root-hub reinit, and adding code to ohci-hcd to turn on ports during
PCI controller resume. (Other bus glue resume methods for platforms
supporting high-speed controllers would need a similar change, if any
existed.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove atomic operations on the reference counter for EHCI queue heads.
On various platforms (including ppc7448), atomic operations are unusable
with dma-coherent memory.
Signed-off-by: Steven J. Hill <sjhill1@rockwellcollins.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that accesses NULL pointer
when disconnected a cable while play music with usb-speaker.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to submit Renesas R8A66597 USB HCD driver.
R8A66597 is Renesas USB 2.0 host and peripheral combined
controller device originally designed for embedded products.
As a limitation of this device, it does not support externel
hub more than 2 tier, and cannot communicate with a USB
device more than 10. Then this device is not compatible with
EHCI and/or OHCI, I wrote driver support patch based on
sl811 code.
This driver has the following unique specifications:
- Implement transfer timeout to share one pipe with plural endpoint.
- Detach detection of a USB device connected to externel hub.
The driver has been tested external hub, usb-hdd, usb-cdrom,
usb-speaker, mice, keyboard, and usbtest driver.
Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements supports for EHCI controllers whose in-memory
data structures are represented in big-endian format. This is needed
(unfortunately) for the AMCC PPC440EPx SoC EHCI controller; the EHCI
spec doesn't specify little-endian format, although that's what most
other implementations use.
The guts of the patch are to introduce the hc32 type and change all
references from le32 to hc32. All access routines are converted from
cpu_to_le32(...) to cpu_to_hc32(ehci, ...) and similar for the other
"direction". (This is the same approach used with OHCI.)
David fixed:
Whitespace fixes; refresh against ehci cpufreq patch; move glue
for that PPC driver to the patch adding it; fix free symbol
capture bugs in modified "constant" macros; and make "hc32" etc
be "le32" unless we really need the BE options, so "sparse" can
do some real good.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI controllers that don't cache enough microframes can get MMF errors
when CPU frequency changes occur between the start and completion of
split interrupt transactions, due to delays in reading main memory
(caused by CPU cache snoop delays).
This patch adds a cpufreq notifier to the EHCI driver that will
inactivate split interrupt transactions during frequency transitions.
It was tested on Intel ICH7 and Serverworks/Broadcom HT1000 EHCI
controllers.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as901) fixes an oversight in ohci-hcd. The
hub_status_data routine must not try to access the controller's
memory-mapped registers if the controller is in a low-power state;
such attempts will cause a crash on some architectures (such as PPC).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=7482.
It sets USB snooping on 4G space for PowerPC platforms without
CONFIG_NOT_COHERENT_CACHE defined.
Reported-by: Stefan Meyer <reyems@telkomsa.net>
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a bug in an OHCI quirk handler for Portege 4000; the
Subvendor is 0x1179 (PCI_VENDOR_ID_TOSHIBA)
not 0x102f (PCI_VENDOR_ID_TOSHIBA_2)
bugid 8510
00:02.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller
[10b9:5237] (rev 03) (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems Unknown device [1179:0004]
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f7eff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as882) fixes a problem with the EHCI BIOS handoff. On my
machine, the BIOS configures the controller and the handoff fails,
leaving the controller configured. During resume-from-disk, this
confuses ehci-hcd into thinking that the controller has not been
tampered with.
The problem is fixed by turning off the Configured Flag whenever a
BIOS handoff is attempted, whether it succeeds or not.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Partial fix for bogosity in the ftdi-elan and u132-hcd drivers ... these
have no business including with the internals of other drivers, much less
doing so in a broken way!!
A previous patch resolved one build fix, this resolves another...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As seen on powerpc-cell et al:
CC [M] drivers/usb/host/ehci-hcd.o
In file included from drivers/usb/host/ehci-hcd.c:941:
drivers/usb/host/ehci-ps3.c:79: error: conflicting types for 'dev_dbg'
include/linux/device.h:576: error: previous definition of 'dev_dbg' was here
make[4]: *** [drivers/usb/host/ehci-hcd.o] Error 1
CC [M] drivers/usb/host/ohci-hcd.o
In file included from drivers/usb/host/ohci-hcd.c:921:
drivers/usb/host/ohci-ps3.c:83: error: conflicting types for 'dev_dbg'
include/linux/device.h:576: error: previous definition of 'dev_dbg' was here
dev_dbg() will check format string for you in dummy case also, so remove
buggers.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixups for the ps3 interrupt routines to support all HV device
in a generic way.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's a patch which adds my device to the list.
This patch enables the broken suspend quirk for the PCI OHCI controller
present in the IT8152F/G RISC-to-PCI Companion Chip.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the old crisv10 HCD ... it can't have built for some time,
doesn't even have a Kconfig entry, was the last driver not to have
been converted to the "hcd" framework, and considering the usbcore
changes since its last patch was merged, has just got to buggy as
all get-out.
I'm told Axis has a new driver, and will be submitting it soon.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the new ohci-pci quirk infrastructure to address the problem it was
created to address: a quirk specific to the Portege 4000, in buzilla as
http://bugzilla.kernel.org/show_bug.cgi?id=6723
Also fix a misuse of "__devinit" for the quirk functions. It must not
be used without first ensuring that the references from the quirk tables
are gone, and that the function using those quirk tables is also gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as872) adds some WARN_ON()s to various error checks which
are never supposed to fail. Unsettlingly, one of them has shown up in
a user's log! Maybe making the warning more visible and having the
call-stack information available will help pinpoint the source of the
problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as870) adds a delay to ehci-hcd's bus_resume routine.
Apparently there are controllers and/or BIOSes out there which need
such a delay to get the ports back into their correct state. This
fixes Bugzilla #8190.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct the offsets of the SI_CTRL, PRI_CTRL registers according to
the Reference Manual errata sheet in order to prevent unwanted
settings regarding burst transactions and priority states.
Signed-off-by: Christian Engelmayer <Christian.Engelmayer@frequentis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Duplicate what Zach Brown did for pr_debug in commit
8b2a1fd1b3
[akpm@linux-foundation.org: fix a couple of things which broke]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the unnecessary bit number from CKENnn_XXXX
definitions for PXA, so that
CKEN0_PWM0 --> CKEN_PWM0
CKEN1_PWM1 --> CKEN_PWM1
...
CKEN24_CAMERA --> CKEN_CAMERA
The reasons for the change of these defitions are:
1. they do not scale - they are currently valid for pxa2xx, but
definitely not valid for pxa3xx, e.g., pxa3xx has bit 3 for camera
instead of bit 24
2. they are unnecessary - the peripheral name within the definition
has already announced its usage, we don't need those bit numbers
to know which peripheral we are going to enable/disable clock for
3. they are inconvenient - think about this: a driver programmer
for pxa has to remember which bit in the CKEN register to turn
on/off
Another change in the patch is to make the definitions equal to its
clock bit index, so that
#define CKEN_CAMERA (24)
instead of
#define CKEN_CAMERA (1 << 24)
this change, however, will add a run-time bit shift operation in
pxa_set_cken(), but the benefit of this change is that it scales
when bit index exceeds 32, e.g., pxa3xx has two registers CKENA
and CKENB, totally 64 bit for this, suppose CAMERA clock enabling
bit is CKENB:10, one can simply define CKEN_CAMERA to be (32 + 10)
and so that pxa_set_cken() need minimum change to adapt to that.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is one significant difference between the behavior of root hubs
(as embodied in host controller hardware) and external hubs: When a
remote-wakeup signal is received, an external hub sends an interrupt
message at the _end_ of the resume sequence but a root hub generates
and interrupt at the _beginning_ of the resume sequence. The host
system must poll for the end of the sequence.
When ehci-hcd was converted to interrupt-driven operation instead of
using polling, the remaining need for this particular poll was
overlooked. This patch (as894) fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as871) fixes a problem introduced by an earlier change.
It turns out that some systems really do need to have a terminating
skeleton QH present whenever FSBR is on. I don't know any way to tell
which systems do need it and which don't; the easiest answer is to
have it there always.
This fixes the NumLock-hang bug reported by Jiri Slaby.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]
Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.
Signed-off-by: Max Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as863) fixes a problem encountered sometimes when resuming
a port on a UHCI controller. The hardware may turn off the
Resume-Detect bit before turning off the Suspend bit, leading usbcore
to think that the port is still suspended and the resume has failed.
The patch makes uhci_finish_suspend() wait until both bits are safely
off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as856) attempts to improve the performance of uhci-hcd by
removing the asynchronous skeleton Queue Headers. They don't contain
any useful information but the controller has to read through them at
least once every millisecond, incurring a non-zero DMA overhead.
Now all the asynchronous queues are combined, along with the period-1
interrupt queue, into a single list with a single skeleton QH. The
start of the low-speed control, full-speed control, and bulk sublists
is determined by linear search. Since there should rarely be more
than a couple of QHs in the list, the searches should incur a much
smaller total load than keeping the skeleton QHs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as855) adds some convenience macros to uhci-hcd, to help
simplify the code for computing hardware DMA pointers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
The AT91SAM9261 needs to activate an AHB clock (HCK0) to use the USB Host
controller. Previously clock.c would just enable it at startup, but now
all the unused clocks are automatically disabled.
Based on patch from Nicolas Ferre.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ps3_system_bus_driver_register is PS3 platform specific function.
On other platforms, it triggers WARN_ON in kref_get.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as848) adds a useful little debugging message to let us
know when ehci-hcd's bus_suspend method runs. The other HCDs have
similar messages; now ehci-hcd doesn't need to feel left out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as850b) disables remote wakeup (and everything else!) on
all EHCI ports when the shutdown() method is called. If remote wakeup
is left active then some systems will reboot instead of powering off.
This fixes Bugzilla #7828.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace appropriate pairs of "kmem_cache_alloc()" + "memset(0)" with the
corresponding "kmem_cache_zalloc()" call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Roland McGrath <roland@redhat.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Joel Becker <Joel.Becker@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
readl() et.al. expect iomem pointer, so WTF force-cast it to normal one???
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that port status change notifications are interrupt-driven,
ehci-hcd needs to tell usbcore when a remote-wakeup resume operation
is finished -- we can no longer rely on the core to poll and find
out. This patch (as843) uses the root-hub status timer to force a
poll after the resume is complete.
The patch also changes the test for detecting when the TDRSMDN resume
period has expired. It's necessary to use time_after_eq() instead of
time_after(), since the polling is triggered precisely by a timer.
The same change is made for TDRSTR reset expiration, for consistency.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch ehci-hcd to use the new polling scheme, which reports root
hub status changes via the interrupt handler, in an asynchronous
fashion. Doing so disables polling for status changes (whose handler is
rh_timer_func).
Tested on a Geode GX machine, which is now capable of running at =~ 5
timer interrupts per second (in the -rt tree), resulting in significant
power savings.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as710) adds a sysfs class-device attribute file named
"companion" for EHCI controllers. The file contains a list of port
numbers that are dedicated to the companion controller; by writing a
port number to the file the user can force a high-speed device
attached directly to the computer to run at full speed. (As far as I
know it is not possible to do this for a device attached to an
external hub.) A port is removed from the file by writing the
negative of its port number.
Several users have asked for this facility and it seems like a useful
thing to have. Every now and then one runs across a device which
behaves much better at full speed than at high speed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as709) changes the way ehci-hcd presents port status
values for ports owned by the companion controller. It no longer
hides the information; in particular, it allows the core to see the
disconnect event that occurs when a full- or low-speed device is
switched over to the companion. This is required for the next patch
in this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as708) introduces a local variable to hold the port
status-register address in ehci-hub.c. There's not much improvement
in the object code, but it sure is a lot easier to read.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as840) fixes the bandwidth allocation mechanism in
uhci-hcd. It has never worked correctly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB OHCI driver bus glue for the PS3 game console.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Restructure the ohci_hcd_mod_init error handling code in to better support
the multiple platform drivers. This does not change the functionality.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB EHCI driver bus glue for the PS3 game console.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch fixes the unbalanced calls to enable_irq_wake() and
disable_irq_wake() in the AT91 USB Host driver.
It should resolve these kernel messages:
Unbalanced IRQ x wake disable
BUG: warning at kernel/irq/manage.c:167/set_irq_wake()
(The original code was debugged before a bug in the genirq wakeup irq
logic was fixed by adding the IRQ wake enable/disable refcounting.
Not all code yet uses the bugfixed model.)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous queues don't need a dummy TD because the Queue Header
isn't managed by the hardware. This patch (as836) removes the
unnecessary dummy TDs.
The patch also fixes a long-standing typo in a comment (a "don't" was
missing -- potentially very confusing!).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as768) improves the debugging checks for the uhci-hcd
frame list. The number of entries displayed is limited to 10, and the
driver now checks for the correct Skeleton QH link value at the end of
each chain of Isochronous TDs. The code to compute these link values
is now used in two spots, so it is moved into its own separate
subroutine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PPC embedded systems can have a ohci controller builtin. In the
new model, it will end up as a driver on the of_platform bus,
this patches takes care of them.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous model had the module_init & module_exit function in the
bus glue .c files themselves. That's a problem if several glues need
to be selected at once and the driver is built has module. This case
is quite common in embedded system where you want to handle both the
integrated ohci controller and some extra controller on PCI.
The ohci-hcd.c file now provide the module_init & module_exit and
appropriate driver registering/unregistering is done conditionally,
using #ifdefs.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a warning introduced by the big endian MMIO EHCI
support patch on platforms that don't have readl_be/writel_be variants
(though mostly harmless as those are called in an if (0) statement,
but gcc still warns).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes a warning introduces by the split endian OHCI support
patch on platforms that don't have readl_be/writel_be variants (though
mostly harmless as those are called in an if (0) statement, but gcc
still warns).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements supports for EHCI controllers whose MMIO
registers are big endian and enables that functionality for
the Toshiba SCC chip. It does _not_ add support for big endian
in-memory data structures as this is not needed for that chip
and I hope it will never be.
The guts of the patch are to convert readl(...) to
ehci_readl(ehci, ...) and similarly for register writes.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch separates support for big endian MMIO register access
and big endian descriptors in order to support the Toshiba SCC
implementation which has big endian registers but little endian
in-memory descriptors.
It simplifies the access functions a bit in ohci.h while at it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch applies David Brownell's suggestion for reworking the
OHCI quirk mechanism via a table of PCI IDs. It adapts the existing
quirks to use that mechanism.
This also moves the quirks to reset() as suggested by the comment
in there. This is necessary as we need to have the endian properly
set before we try to init the controller.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached patch fixes typo in USB driver reported by Chase Douglas on linux-cirrus mailing
list. http://www.freelists.org/archives/linux-cirrus/12-2006/msg00003.html
Signed-off-by: Petr Stetiar <ynezz@true.cz>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as831) adds device_may_wakeup() support to uhci-hcd; it
has been lacking for a long time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of matching all motherboards whose name contains "A7V8X" for a
remote-wakeup hardware bug, this patch (as829) matches only those
boards whose name is exactly equal to "A7V8X". Later motherboards
don't seem to have the bug.
(In fact, it's possible that only one motherboard in the world has the
bug. With only one user reporting problems, it's hard to tell.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ELAN's U132 is a USB to CardBus OHCI controller adapter,
designed specifically for CardBus 3G data cards to
function in machines without a CardBus slot.
The "ftdi-elan" module is a USB client driver, that detects
a supported CardBus OHCI controller plugged into the
U132 adapter and thereafter provides the conduit for
for access by the "u132-hcd" module.
The "u132-hcd" module is a (cut-down OHCI) host controller
that supports a single OHCI function of the CardBus
card inserted into the U132 adapter.
The problem with the initial implementation is that when
the CardBus card inserted into the U132 adapter has multiple
functions (and a CardBus card can support up to 4 functions),
it was the first function that was arbitrarily choosen.
The first batch of 3G cards tested, like the Merlin Qualcomm
V620, have two functions each supporting a seperate USB OHCI
host controller, of which it was that first function that is
wired up to the 3G modem.
Then along comes the Vodafone Mobile Connect 3G/GPRS data card,
aka "Option GT 3G Quad" as printed on it's rear or "Option N.V.
GlobeTrotter Fusion Quad Lite" as read with "lspci -v". And it
has the meaningful functionality in the second CardBus function.
That presents a problem because it was the "ftdi-elan" module
alone that knows how to communicate to the embedded CardBus slot
and the "u132-hcd" module alone that knows how to access the
pcmcia configuration and CardBus accessible memory space. And
of course, the information about attached (internally hardwired)
devices is contained within USB configuration embedded somewhere
within the CardBus card.
If only the "u132-hcd" module probe() interface could return a
result code that propagated back to the instigating function
platform_device_register() then the "ftdi-elan" module could
try an alternative CardBus function. However in spite of
the recent changes to the drivers/base/ routines that moved
device_attach() from bus_add_device() to bus_attach_device()
both of those routines lose the "failed to attach" 0 result
code and thus the calling routine, namely device_add() is
incapable of propaging the "failed to attach" condition back
to platform_device_add() and consequently back to the caller
of platform_device_register()
Experiments show that patching bus_attach_device() to return
ENODEV fails with the kernel locking up very early during
boot. But, however, if the patch is restricted to calls from
platform_device_add() then it does seem to work.
Unfortunately, until the kernel's drivers/base is properly
modified to propagate -ENODEV back to the caller of
platform_device_register(), it is necessary to "fix" the
"ftdi-elan" module by importing knowledge from the
"u132-hcd" module. This is the reason for the duplicated
functionality introduced in this patch.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have found a problem where the root_port_reset() goes into an infinite
loop and stalls the kernel.
This happens when a hardware fault inside the machine occurs during a small
timing window. In case of USB device connection, if a USB device responds to
hcd_submit_urb(), and later the controller fails before root_port_reset(),
root_port_reset() will loop infinitely because ohci_readl() will always
return "-1". Such a failure can include ejecting a CardBus OHCI controller.
The probability of this problem is low, but it will increase if PnP type
usage is frequent. The attached patch can solve this problem and I believe
that it is better to fix this problem.
Signed-off-by: Takamasa Ohtake <ohtake-txa@necst.nec.co.jp>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove a warning about an unused variable in the OHCI bus glue for at91.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is an OHCI cleanup patch ... it removes a lot of erroneous whitespace
(space before tab, at end of line) as well as the obsolete inline changelog.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain boards seem to like to issue false overcurrent notifications,
for example on ports that don't have anything connected to them. This
looks like a hardware error, at the level of noise to those ports'
overcurrent input signals (or non-debounced VBUS comparators). This
surfaces to users as truly massive amounts of syslog spam from khubd
(which is appropriate for real hardware problems, except for the
volume from multiple ports).
Using this new "ignore_oc" flag helps such systems work more sanely,
by preventing such indications from getting to khubd (and spamming
syslog). The downside is of course that true overcurrent errors will
be masked; they'll appear as spontaneous disconnects, without the
diagnostics that will let users troubleshoot issues like
short-circuited cables. In addition, controllers with no devices
attached will be forced to poll for new devices rather than relying on
interrupts, since each overcurrent event would generate a new
interrupt.
This patch (as826) is essentially a copy of David Brownell's ignore_oc
patch for ehci-hcd, ported to uhci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When u132-hcd is built, it includes local header ohci.h, which appears
to have been intended only for use by ohci-hcd.
This throws warnings about functions which are defined and not used.
The warnings thrown are because three small functions are implemented in
the header, but not declared 'inline', a rather strange affair.
Since these functions are small, let's go ahead and define them as
'inline', just like the inline functions surrounding them. This makes
things more consistent, and kills the warnings.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (76 commits)
[ARM] 4002/1: S3C24XX: leave parent IRQs unmasked
[ARM] 4001/1: S3C24XX: shorten reboot time
[ARM] 3983/2: remove unused argument to __bug()
[ARM] 4000/1: Osiris: add third serial port in
[ARM] 3999/1: RX3715: suspend to RAM support
[ARM] 3998/1: VR1000: LED platform devices
[ARM] 3995/1: iop13xx: add iop13xx support
[ARM] 3968/1: iop13xx: add iop13xx_defconfig
[ARM] Update mach-types
[ARM] Allow gcc to optimise arm_add_memory a little more
[ARM] 3991/1: i.MX/MX1 high resolution time source
[ARM] 3990/1: i.MX/MX1 more precise PLL decode
[ARM] 3986/1: H1940: suspend to RAM support
[ARM] 3985/1: ixp4xx clocksource cleanup
[ARM] 3984/1: ixp4xx/nslu2: Fix disk LED numbering (take 2)
[ARM] 3994/1: ixp23xx: fix handling of pci master aborts
[ARM] 3981/1: sched_clock for PXA2xx
[ARM] 3980/1: extend the ARM Versatile sched_clock implementation from 32 to 63 bit
[ARM] 3979/1: extend the SA11x0 sched_clock implementation from 32 to 63 bit period
[ARM] 3978/1: macro to provide a 63-bit value from a 32-bit hardware counter
...
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/pcmcia/ds.c
Fix up merge failures with Linus's head and fix new compile failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
struct pcmcia_device *p_dev->conf.ConfigBase and .Present are set in almost
all PCMICA driver right at the beginning, using the same calls but slightly
different implementations. Unfiy this in the PCMCIA core.
Includes a small bugfix ("drivers/net/pcmcia/xirc2ps_cs.c: remove unused
label") from and Signed-off-by Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (103 commits)
usbcore: remove unused argument in autosuspend
USB: keep count of unsuspended children
USB hub: simplify remote-wakeup handling
USB: struct usb_device: change flag to bitflag
OHCI: make autostop conditional on CONFIG_PM
USB: Add autosuspend support to the hub driver
EHCI: Fix root-hub and port suspend/resume problems
USB: create a new thread for every USB device found during the probe sequence
USB: add driver for the USB debug devices
USB: added dynamic major number for USB endpoints
USB: pegasus error path not resetting task's state
USB: endianness fix for asix.c
USB: build the appledisplay driver
USB serial: replace kmalloc+memset with kzalloc
USB: hid-core: canonical defines for Apple USB device IDs
USB: idmouse cleanup
USB: make drivers/usb/core/driver.c:usb_device_match() static
USB: lh7a40x_udc remove double declaration
USB: pxa2xx_udc recognizes ixp425 rev b0 chip
usbtouchscreen: add support for DMC TSC-10/25 devices
...
Unlike UHCI, OHCI does not exert any DMA load on the system when no
devices are connected. Consequently there is no advantage to doing
an autostop other than the power savings, so we shouldn't compile the
necessary code unless CONFIG_PM is enabled.
This patch (as820) makes the root-hub suspend and resume routines
conditional on CONFIG_PM. It also prevents autostop from activating
if the device_may_wakeup flag isn't set; some people use this flag to
alert the driver about Resume-Detect bugs in the hardware.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as738b) fixes numerous problems in the controller/root-hub
suspend/resume/remote-wakeup support in ehci-hcd:
The bus_resume() routine should wake up only the ports that
were suspended by bus_suspend(). Ports that were already
suspended should remain that way.
The interrupt mask is used to detect loss of power in the
bus_resume() routine (if the mask is 0 then power was lost).
However bus_suspend() always sets the mask to 0. Instead the
mask should retain its normal value, with port-change-detect
interrupts disabled if remote wakeup is turned off.
The interrupt mask should be reset to its correct value at the
end of bus_resume() regardless of whether power was lost.
bus_resume() reinitializes the operational registers if power
was lost. However those registers are not in the aux power
well, hence they can lose their values whenever the controller
is put into D3. They should always be reinitialized.
When a port-change interrupt occurs and the root hub is
suspended, the interrupt handler should request a root-hub
resume instead of starting up the controller all by itself.
There's no need for the interrupt handler to request a
root-hub resume every time a suspended port sends a
remote-wakeup request.
The pci_resume() method doesn't need to check for connected
ports when deciding whether or not to reset the controller.
It can make that decision based on whether Vaux power was
maintained.
Even when the controller does not need to be reset,
pci_resume() must undo the effect of pci_suspend() by
re-enabling the interrupt mask.
If power was lost, pci_resume() must not call ehci_run().
At this point the root hub is still supposed to be suspended,
not running. It's enough to rewrite the command register and
set the configured_flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following possible cleanups:
- make the needlessly global ftdi_release_platform_dev() static
- remove the unused usb_ftdi_elan_read_reg()
- proper prototypes for the following functions:
- usb_ftdi_elan_read_pcimem()
- usb_ftdi_elan_write_pcimem()
Note that the misplaced prototypes for the latter ones in
drivers/usb/host/u132-hcd.c were buggy. Depending on the calling
convention of the architecture calling one of them could have turned
your stack into garbage.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global "u132_hcd_wait" static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain boards seem to like to issue false overcurrent notifications, for
example on ports that don't have anything connected to them. This looks
like a hardware error, at the level of noise to those ports' overcurrent
input signals (or non-debounced VBUS comparators). This surfaces to users
as truly massive amounts of syslog spam from khubd (which is appropriate
for real hardware problems, except for the volume from multiple ports).
Using this new "ignore_oc" flag helps such systems work more sanely, by
preventing such indications from getting to khubd (and spam syslog). The
downside is of course that true overcurrent errors will be masked; they'll
appear as spontaneous disconnects, without the diagnostics that will let
users troubleshoot issues like short circuited cables.
Note that the bulk of these reports seem to be with VIA southbridges, but
I think some were with Intel ones.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI hooks for high speed electrical tests of the root hub ports.
The expectation is that a usermode program actually triggers the test,
making the same control request it would make for an external hub.
Tests for peripheral upstream ports would issue a different request.
In all cases, the hardware needs re-initialization before it could
be used "normally" again (e.g. unplug/replug, rmmod/modprobe).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the other root-hub suspend or resume log messages, in ohci-hcd or
any of the other host controller drivers, use the debug priority
level. This patch (as815) makes the one single exception behave like
all the rest.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as811) removes some stale testing code from the root-hub
resume routine in ohci-hcd. It also adds a spin_lock_irq() call that
inadvertently got left out of an error pathway.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as808b) moves the Root Hub Status Change interrupt-disable
code in ohci-hcd back into the interrupt handler proper, to avoid the
chance of adverse interactions with mediocre hardware implementations.
It also deletes the root-hub status timer from within the interrupt-enable
routine. There's no need to poll for status any more once interrupts are
re-enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as806) fixes a compiler warning when ohci-hcd is built
with CONFIG_PM turned off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A number of configuration file changes.
These are mainly to replace references to ARCH_AT91RM9200 and
ARCH_AT91SAM9261 with the common/generic ARCH_AT91. That way we don't
need to mention every specific AT91 processor explicitly.
Also adds the configuration option for AT91SAM9260-EK and AT91SAM9261-EK
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
When a suspended OHCI controller sees a port's status change, it sets
both the Root-Hub-Status-Change and the Resume-Detect bits in the
Interrupt Status register. Processing both these bits, the driver
tries to resume the root hub twice!
This patch (as807) fixes the bug by ignoring RD if RHSC is set. It
also prints a slightly more informative log message when a
remote-wakeup event occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as822) prevents the OHCI autostop mechanism from kicking in
if the root hub is not able or not allowed to issue wakeup requests.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as798) adds a workaround to uhci-hcd. At least one Asus
motherboard is wired in such a way that any device attached to a
suspended UHCI controller will prevent the system from entering
suspend-to-RAM by immediately waking it up. The only way around the
problem is to turn the controller off instead of suspending it.
This fixes Bugzilla #6193.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OHCI bus glue for the Philips PNX chips is missing a few calls.
- Bus suspend/resume were wrongly omitted in the original submission.
- Two new calls were added since that glue was submitted:
* Root hub irq enable call
* Shutdown hook for usbcore
Plus usb_bus.hcpriv has now been removed from usbcore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts 26f953fd88 which caused
resume problems on the mac mini.
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a more correct fix for the way the ohci hcd was referencing pt_regs
in the unlink paths.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Thanks to Andrew for the original patch for this.
I need to upgrade my version of gcc to catch these things...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as790b) adds "autostop" support to ohci-hcd: the driver
will automatically stop the host controller when no devices have been
connected for at least one second. This feature is useful when the
USB autosuspend facility isn't available, such as when
CONFIG_USB_SUSPEND hasn't been set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The autosuspend technique used by ohci-hcd doesn't mesh well with the
newer USB core autosuspend code. This patch (as789) removes ohci-hcd's
autosuspend support. Now the driver will be usable, but it won't
automatically go into a low-power state when no devices are connected.
That's for a later patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We want to avoid legacy APIs like pci_find_slot().
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revamps handling of the hardware "async advance" IRQ, and its watchdog
timer. Basically it dis-entangles that important timeout from the others,
simplifying the associated state and code to make it more robust.
This reportedly improves behavior of EHCI on some systems with VIA chips,
and AFAIK won't affect non-VIA hardware. VIA systems need this code to
recover from silcon bugs whereby the "async advance" IRQ isn't issued.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When ohci-hcd is shutting down (for rmmod or PC-card removal), there is
a window when the device is shut down, HC communication area (->hcca)
is freed, but the core has not called "free_irq" yet. If another device
triggers a shared interrupt in this window, we oops when trying to
access the freed ->hcca.
This patch removes the window by calling free_irq before ->hcca is freed.
The patch is tested at the PC hotplug test rig at Stratus, and with
rmmod by Rafael Wysocki.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This "u132-hcd" module is one half of the "driver" for
ELAN's U132 which is a USB to CardBus OHCI controller
adapter. This module needs the "ftdi-elan" module in
order to communicate to CardBus OHCI controller inserted
into the U132 adapter.
When the "ftdi-elan" module detects a supported CardBus
OHCI controller in the U132 adapter it loads this "u132-hcd"
module.
Upon a successful device probe() the single workqueue
is started up which does all the processing of commands
from the USB core that implement the host controller.
The workqueue maintains the urb queues and issues commands
via the functions exported by the "ftdi-elan" module. Each
such command will result in a callback.
Note that the "ftdi-elan" module is a USB client driver.
Note that this "u132-hcd" module is a (cut-down OHCI)
host controller.
Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.
Signed-off-by: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as740) removes the existing support for autosuspend of
root hubs. That support fit in rather awkwardly with the rest of
usbcore and it was used only by ohci-hcd. It won't be needed any more
since the hub driver will take care of autosuspending all hubs, root
or external.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Yoshihiro Shimoda