New chipsets introduced variant Rx FIFO sizes that need to be taken into
account when setting up the tx pause watermarks. This patch introduces
the new device feature flags based on a version and implements the new
watermarks.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch supports a new fix in hardware regarding tx collisions. In
the cases where we are in autoneg mode and the link partner is in forced
mode, we need to setup the tx deferral register differently in order to
reduce collisions on the wire.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When ARP completes due to a request rather than a reply the neighbor is
marked NUD_STALE instead of reachable (see arp_process()). The handler
for the resulting netevent needs to check also for NUD_STALE.
Failure to use the arp entry can cause RDMA connection failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Show whether the MAC address was read from the EEPROM or
the onboard PAR registers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reading the ID register does not always return the correct ID
from the device, so we retry several times to see if we get
a correct value.
These failures seem to be excaserbated by the speed of the
access to the chip (possibly time between issuing the address
and then the data cycle).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add entry to handle the MII ioctl() calls via the
generic_mii_ioctl call.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the platform data to specify to the DM9000 driver
that there is no posibility of an attached EEPROM on the
device, so default all reads to 0xff and ignore any
write operations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The writing of the data should implicitly truncate
the data to 8bits, so do not bother with the ands
in the code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the cal_CRC as this is basically wrappering the
ether_crc_le function, and is only being used by the
multicast hash table functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code was using a delay of 8ms, when it should have been
using the EEPROM status flag from the device to indicate the
EEPROM transaction had finished.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the netif_msg_*() macros to enable the debugging based
on the board's msg_enable field. The output still goes via
the dev_dbg() macros, so will be tagged and output as
appropriate.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We have a perfectly good version control system, so we do not
need to duplicate change comments in the header for this code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ensure we hold the spinlock whilst the registers and being
modified even though we hold the overall lock. This should
protect against an interrupt happening whilst we are using
the device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the old hack to program an initial EEPROM setting
into the DM9000 as we now have ethtool support for reading
and writing the EEPROM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow the msg_enable value to be read and written by
the ethtool interface.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool support to access the configuration EEPROM
connected to the DM9000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a mutex to serialise access to the chip functions from
entries such as the ethtool and the MII code. This should
reduce the amount of time the spinlock is held to protect
the address register.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The srom array in the board data is only being used in the device probe
routines. The probe also only uses the first 6 bytes of an array
we spend 512ms reading 128 bytes from. Change to reading the
MAC area directly to the MAC address structure.
As a side product, we rename the read_srom_word to dm9000_read_eeprom
to bring it into line with the rest of the driver. No change is made
to the delay in this function, which will be dealt with in a later
patch.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We can use sleeping functions when reading and writing the
PHY registers, so let us sleep instead of busy waiting for
the PHY.
Note, this also fixes a bug reading the PHY where only 100uS
was being used instead of 150uS
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The phy read and write routines call udelay() with the board
lock held, and with the posibility of IRQs being disabled. Since
these delays can be up to 500usec, and are only required as we
have to save the chip's address register.
To improve the behaviour, hold the lock whilst we are writing
and then restore the state before the delay and then repeat
the process once the delay has happened.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove the timer based MII phy polling, as this is
currently broken with the new EEPROM code that now
uses mutexes to protect the phy access.
This will need to be replaced in the future by some
form of mutex safe mechanism for reading the MII
phy status.
The replacement has not been done here as changing
this patch, which is early in the sequence has quite
a knock-on effect. Once this series is merged, then
a new presentation of an patch to poll the MII link
status can be added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the flags in the IRQ resource to specify the type of
IRQ being requested, so that systems which do not have
level-based interrupts, or change the interrupt in some
other way can specify this without making an #ifdef mess
in the driver.
This is specifically designed to undo the change in commit
4e4fc05a2b which hardwires the
type for everyone but blackfin to IRQT_RISING, which breaks
all a number of Simtec boards which use (and setup in the
bootloader) active low IRQs.
Note, although there where originally objections due to
the use of IORESOURCE_IRQ and IRQT_ flags not sharing the
same definition, at least <include/linux/interrupt.h> notes
these are the same.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CC: Daniel Mack <daniel@caiaq.de>
CC: Bryan Wu <bryan.wu@analog.com>
CC: Alex Landau <landau.alex@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the debug macros to use the compiler to elide any
unnecessary debug level, and to allow device configurable
debug control.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move to using dev_dbg() and friends for the output of
information to the user.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch adds a flag to the DM9000 platform data which, when set,
configures the device to use an external PHY.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linuy@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch from: Laurent Pinchart <laurentp@cse-semaphore.com>
This patch splits the receive status in 8bit wide fields and convert the
packet length from little endian to CPU byte order.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Add common code for stopping queue.
2. No need to call netif_stop_queue followed by netif_wake_queue (and
infact a netif_start_queue could have been used instead), instead
call stop_queue if required, and remove code under USE_GTS macro.
3. There is no need to check for netif_queue_stopped, as the network
core guarantees that for us (I am sure every driver could remove
that check, eg e1000 - I have tested that path a few billion times
with about a few hundred thousand qstops but the condition never
hit even once).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The e1000 driver stores the content of the PCI resources into
unsigned long's before ioremapping. This breaks on 32 bits
platforms that support 64 bits MMIO resources such as ppc 44x.
This fixes it by removing those temporary variables and passing
directly the result of pci_resource_start/len to ioremap.
The side effect is that I removed the assignments to the netdev
fields mem_start, mem_end and base_addr, which are totally useless
for PCI devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
--
drivers/net/e1000/e1000_main.c | 18 +++++-------------
1 file changed, 5 insertions(+), 13 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for dual network (net_device) interface so that ethernet
and wireless can own separate ethX interfaces.
V2
- Fix the bug that bringing down and up the interface keeps rx
disabled.
- Make 'gelic_net_poll_controller()' extern , as David Woodhouse
pointed out at the previous submission.
- Fix weird usage of member names for the rx descriptor chain
V1
- Export functions which are convenient for both interfaces
- Move irq allocation/release code to driver probe/remove handlers
because interfaces share interrupts.
- Allocate skbs by using dev_alloc_skb() instead of netdev_alloc_skb()
as the interfaces share the hardware rx queue.
- Add gelic_port struct in order to abstract dual interface handling
- Change handlers for hardware queues so that they can handle dual
{source,destination} interfaces.
- Use new NAPI functions
This is a prerequisite for the new PS3 wireless support.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for interrupt driven port link status detection.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove some ethtool handlers, which duplicate functionality that was already
provided by the common ethtool handlers.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code cleanup:
- Use appropriate prefixes for names instead of fixed 'gelic_net'
so that objects of the functions, variables and constants can be estimated.
- Remove definitions for IPSec offload to the gelic hardware. This
functionality is never supported on PS3.
- Group constants with enum.
- Use bitwise constants for interrupt status, instead of bit numbers to
eliminate shift operations.
- Style fixes.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark the members of the structure for DMA descriptors with proper endian
annotations and use the appropriate accessor macros.
As the gelic driver works only on PS3, all these macros will be
expanded to null.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The device id for lv1_net_set_interrupt_status_indicator() is wrong.
This path would be invoked only in the case of an initialization failure.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updates the 8139too driver to work with recently added
(a724605cb7) declared coherent memory
patch for the Dreamcast.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To kill the volatiles also switch it to stop poking ISA memory directly
without going through readb and friends.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change hard coded 2 to NET_IP_ALIGN. Added new #define with comments.
Tested amd_64
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to blacklist this device, as it should be handled by
ldusb driver.
Reported-by: stephen <stephen.ware@eqware.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The old code (before move) stopped further processing of the
event after it has been already processed by the quirk handler.
The new code didn't propagate the return value properly, and
therefore the processing always proceeded, which was wrong.
This patch fixes it. Pointed out in kernel.org bugzilla #9842
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds new GTCO CalComp USB device PIDs to the blacklist.
Signed-off-by: Jeremy A. Roberson <jroberson@gtcocalcomp.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
commit 813a0eb233
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Fri Jan 25 22:17:10 2008 +0100
ide: switch idedisk_prepare_flush() to use REQ_TYPE_ATA_TASKFILE requests
...
broke flush requests.
Allocating IDE command structure on the stack for flush requests is not
a very brilliant idea:
- idedisk_prepare_flush() only prepares the request and it doesn't wait
for it to be completed
- there are can be multiple flush requests queued in the queue
Fix the problem (per hints from James Bottomley) by:
- dynamically allocating ide_task_t instance using kmalloc(..., GFP_ATOMIC)
- adding new taskfile flag (IDE_TFLAG_DYN)
- calling kfree() in ide_end_drive_command() if IDE_TFLAG_DYN is set
(while at it rename 'args' to 'task' and fix whitespace damage)
[ This will be fixed properly before 2.6.25 but this bug is rather
critical and the proper solution requires some more work + testing. ]
Thanks to Sebastian Siewior and Christoph Hellwig for reporting the
problem and testing patches (extra thanks to Sebastian for bisecting
it to the guilty commmit).
Tested-by: Sebastian Siewior <ide-bug@ml.breakpoint.cc>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Introduce new option CONFIG_BLK_DEV_IDEDMA_SFF for non-PCI SFF-8038i compatible
bus mastering IDE controllers (which there are a few known), thus fixing a hack
made for Palmchip BK3710 controller...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Saturday 09 February 2008, Adrian Bunk wrote:
> Commit 9e016a7192 causes the following
> compile error:
>
> <-- snip -->
>
> ...
> CC drivers/ide/arm/bast-ide.o
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c: In function 'bastide_register':
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:31: error: 'hwif' redeclared as different kind of symbol
> /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/arm/bast-ide.c:29: error: previous definition of 'hwif' was here
> make[4]: *** [drivers/ide/arm/bast-ide.o] Error 1
>
> <-- snip -->
Remove 'ide_hwif_t **hwif' argument from bastide_register()
(together with write-only ifs[]).
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
rq->cmd[0] is never set to REQ_IDETAPE_READ_BUFFER so remove
REQ_IDETAPE_READ_BUFFER handling from idetape_create_write_cmd()
and the define itself.
Then remove no longer used idetape_create_read_buffer_cmd()
and IDETAPE_RETRIEVE_FAULTY_BLOCK define.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Thursday 03 January 2008, Robert Hancock wrote:
[...]
> How about getting rid of this stupid thing in drivers/ide/ide.c:
>
> #define       REVISION        "Revision: 7.00alpha2"
>
> which is used in:
>
> printk(KERN_INFO "Uniform Multi-Platform E-IDE driver " REVISION "\n");
>
> It's been 7.00alpha2 for god knows how long, so clearly this version
> number is not useful..
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alan has noticed that distros always enabled burst mode
(+ datasheet confirms that it is the right thing to do).
Thus fix pdc202xx_old host driver to do it unconditionally
and remove no longer needed CONFIG_PDC202XX_BURST option.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Probe port _after_ it is fully initialized.
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't set 'restore' flag for ide_unregister() when initializing new
interface.
[ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
by commit 909f4369bc ]
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert palm_bk3710 host driver to use ide_device_add() instead of
ide_register_hw() (while at it drop doing "ide_unregister()" loop which
tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot
cannot be find).
[ identical change as done to bast-ide/ide-cs/delkin_cb host drivers
by commit 9e016a7192 ]
* Rename 'ide_ctlr_info' to 'hw' and 'index' to 'i' while at it.
Cc: Anton Salnikov <asalnikov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace the check for hwgroup->handler and printk(KERN_CRIT, ...) at the start
of __ide_set_handler() with mere BUG_ON() while removing such from the caller,
ide_execute_command(). Fix up the code formatting, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove stale comment from the cs5520 IDE driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I have reviewed all blk-end-request patches again to confirm whether
there are any similar problems with the last week's ide-cd panic:
http://lkml.org/lkml/2008/1/29/140
And I found a possible similar bug in ide-io change:
ide_end_drive_cmd() could be called for blk_pc_request() which could
have bios. To complete such requests correctly, we need to pass
the actual size of the request.
Otherwise, __blk_end_request() returns 1 because the request still has
bios, and the system will BUG() unnecessarily.
The following patch fixes the bug and should be applied on top of
Linus' git.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We want to allow different implementations of pci_raw_ops for standard
and extended config space on x86. Rather than clutter generic code with
knowledge of this, we make pci_raw_ops private to x86 and use it to
implement the new raw interface -- raw_pci_read() and raw_pci_write().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/starfire.c:219: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/via-velocity.c:443: error: chip_info_table causes a section type conflict
on this one I had to remove the __devinitdata too. Don't know why.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/natsemi.c:245: error: natsemi_pci_info causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/typhoon.c:137: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warnings:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x19723): Section mismatch in reference from the function ISACVersion() to the variable .devinit.data:ISACVer
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2005b): Section mismatch in reference from the function setup_avm_a1_pcmcia() to the function .devinit.text:setup_isac()
ISACVer were only used from function annotated __devinit
so add same annotation to ISACVer.
One af the fererencing functions missed __devinit so add it
and kill an additional warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x722): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_teles3()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x72c): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_s0box()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x736): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_telespci()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x747): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_avm_pcipnp()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x74e): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_elsa()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x755): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_diva()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x75c): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_sedlbauer()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x763): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_netjet_s()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x76a): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_hfcpci()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x771): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_hfcsx()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x778): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_niccy()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x77f): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_bkm_a4t()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x786): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_sct_quadro()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x78d): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_gazel()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x794): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_w6692()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x79b): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_netjet_u()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x7a2): Section mismatch in reference from the function hisax_cs_setup_card() to the function .devinit.text:setup_enternow_pci()
checkcard() are the only user of hisax_cs_setup_card().
And checkcard is only used during init or when hot plugging
ISDN devices. So annotate hisax_cs_setup_card() with __devinit.
checkcard() is used by exported functions so it cannot be
annotated __devinit. Annotate it with __ref so modpost
ignore references to _devinit section.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x1b276): Section mismatch in reference from the function inithscxisac() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x1b286): Section mismatch in reference from the function inithscxisac() to the function .devinit.text:initisac()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x1fec7): Section mismatch in reference from the function AVM_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x21669): Section mismatch in reference from the function AVM_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x21671): Section mismatch in reference from the function AVM_card_msg() to the function .devinit.text:initisac()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2991e): Section mismatch in reference from the function Sedl_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x29936): Section mismatch in reference from the function Sedl_card_msg() to the function .devinit.text:initisac()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2993e): Section mismatch in reference from the function Sedl_card_msg() to the function .devinit.text:initisar()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2e026): Section mismatch in reference from the function NETjet_S_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x2e02e): Section mismatch in reference from the function NETjet_S_card_msg() to the function .devinit.text:initisac()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x37813): Section mismatch in reference from the function BKM_card_msg() to the function .devinit.text:clear_pending_isac_ints()
WARNING: drivers/isdn/hisax/built-in.o(.text+0x37823): Section mismatch in reference from the function BKM_card_msg() to the function .devinit.text:initisac()
initisar(), initisac() and clear_pending_isac_ints()
were all used via a cardmsg fnction - which may be called
ouside __devinit context.
So remove the bogus __devinit annotation of the
above three functions to fix the warnings.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warning:
WARNING: drivers/isdn/hisax/built-in.o(.text+0x35818): Section mismatch in reference from the function hfcsx_card_msg() to the function .devinit.text:inithfcsx()
hfcsx_card_msg() may be called outside __devinit context.
Following the program logic is looks like the CARD_INIT branch
will only be taken under __devinit context but to be consistent
remove the __devinit annotation of inithfcsx() so we
do not mix non-__devinit and __devinit code.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/pppol2tp.c: In function `pppol2tp_seq_tunnel_show':
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 4)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 5)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 6)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 7)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 8)
drivers/net/pppol2tp.c:2295: warning: long long unsigned int format, __u64 arg (arg 9)
drivers/net/pppol2tp.c: In function `pppol2tp_seq_session_show':
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 5)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 6)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 7)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 8)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 9)
drivers/net/pppol2tp.c:2328: warning: long long unsigned int format, __u64 arg (arg 10)
Not all platforms implement u64 with unsigned long long. eg: powerpc.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-3.4.4 on powerpc:
drivers/net/bnx2.c:67: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrew Morton <akpm@linux-foundation.org>
gcc-3.4.4 on powerpc:
drivers/net/bnx2x.c:73: error: version causes a section type conflict
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beginning from commit 4138cc3418, ioremap_nocache() sets the _PAGE_PWT
flag.
Lguest doesn't accept a guest pte with a _PWT flag and reports a "bad
page table entry" in that case.
Accept guest _PAGE_PWT page table entries.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add function definition and extern variables to asm-x86/acpi.h.
All of these are used in bus.c in ifdef(CONFIG_X86) sections, so are
only added to the x86 include headers. boot.c already includes acpi.h
so no changes are needed there.
Fixes the following:
arch/x86/kernel/acpi/boot.c:83:4: warning: symbol 'acpi_sci_flags' was not declared. Should it be static?
arch/x86/kernel/acpi/boot.c:84:5: warning: symbol 'acpi_sci_override_gsi' was not declared. Should it be static?
arch/x86/kernel/acpi/boot.c:421:13: warning: symbol 'acpi_pic_sci_set_trigger' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
Kbuild: Fix deb-pkg target to work with kernel versions ending with -<text-without-digit>
ide: introduce HAVE_IDE
kbuild: silence CHK/UPD messages according to $(quiet)
scsi: fix makefile for aic7(3*x)
kbuild/modpost: Use warn() for announcing section mismatches
Add binoffset to gitignore
kbuild/modpost: improve warnings if symbol is unknown
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: extend ricoh_mmc to support Ricoh RL5c476
at91_mci: use generic GPIO calls
sdhci: add num index for multi controllers case
MAINTAINERS: remove non-existant URLs
mmc: remove sdhci and mmc_spi experimental markers
mmc: Handle suspend/resume in Ricoh MMC disabler
Sony MemoryStick cards are used in many products manufactured by Sony.
They are available both as storage and as IO expansion cards. Currently,
only MemoryStick Pro storage cards are supported via TI FlashMedia
MemoryStick interface.
[mboton@gmail.com: biuld fix]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Miguel Boton <mboton@gmail.co>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two problems in the vt220 intialization:
o Currently the vt220 console looses early printk events until the
the vt220 tty is registered.
o console should work if tty_register fails
sclp_vt220_con_init calls __sclp_vt220_init and register_console.
It does not register the driver with the sclp core code via
sclp_register. That results in an sclp_send_mask=0. Therefore,
__sclp_vt220_emit will reject buffers with EIO. Unfortunately
register_console will cause the printk buffer to be sent to the
console and, therefore, every early message gets dropped. The
sclp_send_mask is set later during boot, when sclp_vt220_tty_init
calls sclp_register.
The solution is to move the sclp_register call from sclp_vt220_tty_init
to __sclp_vt220_init. This makes sure that the console is properly
registered with the sclp subsystem before the first log buffer messages
are passed to the vt220 console.
We also adopt the cleanup on error to keep the console alive if
tty_register fails.
Thanks to Peter Oberparleiter and Heiko Carstens for review and ideas
for improvement.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If qdio establish runs in parallel with a channel error,
ccw_device_start_timeout may not trigger the qdio_timeout_handler.
In this case neither QDIO_IRQ_STATE_ESTABLISHED nor
QDIO_IRQ_STATE_ERR is reached and the following wait_event hangs
forever.
Solution: do not make use of the timeout option with
ccw_device_start, but add a timeout to the following wait_event.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not start ap poll thread per default to increase perfomance with
z/VM.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix bug introduced by my latest fix to the aic7xxx Makefile.
Test build on x86 32 and 64 bit.
Without and with -j (parallel build)
Building firmaware is br0ken with O=... but this
is unrelated to this bug-fix.
Tested-by: Adrian Bunk <bunk@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Add some initial documentation detailing what acer-wmi is, and how to use
it. Update the Kconfig entry with a reference to the documentation.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update references to sonypi.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update references to sony-laptop.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update references to thinkpad-acpi.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
The last posted version of this patch gave compile error
on IA64. So, here goes yet another rewrite of the patch.
Convert cpu_idle_wait() to cpuidle_kick_cpus() which is
SMP-only, and gives error on non supported CPU.
Changes from last patch sent by Kevin:
Moved the definition of kick_cpus back to cpuidle.c from cpuidle.h:
* Having it in .h gives #error on archs which includes the header file without
actually having CPU_IDLE configured. To make it work in .h, we need one more
#ifdef around that code which makes it messy.
* Also, the function is only called from one file. So, it can be in declared
statically in .c rather than making it available to everyone who includes
the .h file.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There is some leftover cruft from the old quirk infrastructure that causes
us to be unable to set the backlight on older laptops.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
tc1100-wmi has not undergone as much testing as acer-wmi, so it certainly
should be marked as experimental as well until we get more user feedback.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
In static case sbshc must be compiled ahead of sbs, so that
hc is configured first.
http://bugzilla.kernel.org/show_bug.cgi?id=9910
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Implements kernel command line partitioning support for the CS5535/CS5536 chipsets driver.
For that the following is done:
* cs553x_cleanup(): try the cleanup for all chip selects to not leak memory
* Assign a unique name for each chip select to be separately addressable in the command line mtd-id portion(s)
* Use the already defined PIN_OPT_IDE constant where appropriate for readability
* Include command line partitioning support when CONFIG_MTD_PARTS is set
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Remove unused struct ib_device.flags member
IB/core: Add IP checksum offload support
IPoIB: Add send gather support
IPoIB: Add high DMA feature flag
IB/mlx4: Use multiple WQ blocks to post smaller send WQEs
mlx4_core: Clean up struct mlx4_buf
mlx4_core: For 64-bit systems, vmap() kernel queue buffers
IB/mlx4: Consolidate code to get an entry from a struct mlx4_buf
Thanks to Kay for keeping us honest.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Cc: "Williams, Dan J" <dan.j.williams@intel.com>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x25_asy does not take an ldisc reference before calling the flush method.
Fix it to use the helper function we provide.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch acts as a preparation for using checksum offload for IB
devices capable of inserting/verifying checksum in IP packets. The
patch does not actaully turn on NETIF_F_SG - we defer that to the
patches adding checksum offload capabilities.
We only add support for send gathers for datagram mode, since existing
HW does not support checksum offload on connected QPs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All current InfiniBand devices can handle all DMA addresses, and it's
hard to imagine anyone would be silly enough to build a new device
that couldn't. Therefore, enable the NETIF_F_HIGHDMA feature for IPoIB.
This has no effect for no, but is needed when we enable gather/scatter
support and checksum stateless offloads.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'cris' of git://www.jni.nu/cris: (158 commits)
CRIS v32: Remove hwregs/timer_defs.h, it is now architecture specific.
CRIS v32: Change drivers/i2c.c locking.
CRIS v32: Rewrite ARTPEC-3 gpio driver to avoid volatiles and general cleanup.
CRIS: Add new timerfd syscall entries.
MAINTAINERS: Add my information for the CRIS port.
CRIS v32: Correct spelling of bandwidth in function name.
CRIS v32: Clean up nandflash.c for ARTPEC-3 and ETRAX FS.
CRIS v10: Cleanup of drivers/gpio.c
CRIS v10: drivers/net/cris/eth_v10.c rename LED defines to CRIS_LED to avoid name clash.
CRIS: Make io_pwm_set_period members unsigned in etraxgpio.h
CRIS: Move ETRAX_AXISFLASHMAP to common Kconfig file.
CRIS: Drop regs parameter from call to profile_tick in kernel/time.c
CRIS v32: Fix minor formatting issue in mach-a3/io.c
CRIS v32: Initialize GIO even if we're rambooting in kernel/head.S
CRIS v32: Remove kernel/arbiter.c, it now exists in machine dependent directory.
CRIS v32: Minor changes to avoid errors in asm-cris/arch-v32/hwregs/reg_rdwr.h
CRIS v32: arch-v32/hwregs/intr_vect_defs.h moved to machine dependent directory.
CRIS v32: Correct offset for TASK_pid in asm-cris/arch-v32/offset.h
CRIS v32: Move register map header to machine dependent directory.
CRIS v32: Let compiler know that memory is clobbered after a break op.
...
* 'for-2.6.25' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Add arch-specific walk_memory_remove() for 64-bit powerpc
[POWERPC] Enable hotplug memory remove for 64-bit powerpc
[POWERPC] Add remove_memory() for 64-bit powerpc
[POWERPC] Make cell IOMMU fixed mapping printk more useful
[POWERPC] Fix potential cell IOMMU bug when switching back to default DMA ops
[POWERPC] Don't enable cell IOMMU fixed mapping if there are no dma-ranges
[POWERPC] Fix cell IOMMU null pointer explosion on old firmwares
[POWERPC] spufs: Fix timing dependent false return from spufs_run_spu
[POWERPC] spufs: No need to have a runnable SPU for libassist update
[POWERPC] spufs: Update SPU_Status[CISHP] in backing runcntl write
[POWERPC] spufs: Fix state_mutex leaks
[POWERPC] Disable G5 NAP mode during SMU commands on U3
There is an outdated comment in serial_core.c also fixed.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the arbitrary 128 device limit for NBD. nbds_max can now be set to
any number. In certain scenarios where devices are used sparsely we have
run into the 128 device limit.
Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of testing hardcoded values, use pci_match_id to reference the
pci_device_id table. Sideways, it allows easy new additions to the table.
[akpm@linux-foundation.org: remove wrongly-added semicolon]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a .show_options super operation to capifs.
Use generic_show_options() and save the complete option string in
capifs_remount().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a LED driver using the PWM on newer SOCs from Atmel; brightness is
controlled by changing the PWM duty cycle. So for example if you've set up
two leds labeled "pwm0" and "pwm1":
echo 0 > /sys/class/leds/pwm2/brightness # off (0%)
echo 80 > /sys/class/leds/pwm2/brightness
echo 255 > /sys/class/leds/pwm2/brightness # on (100%)
Note that "brightness" here isn't linear; maybe that should change. Going
from 4 to 8 probably doubles perceived brightness, while 244 to 248 is
imperceptible.
This is mostly intended to be a simple example of PWM, although it's
realistic since LCD backlights are often driven with PWM to conserve
battery power (and offer brightness options).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PWM device setup, and a simple PWM driver exposing a programming interface
giving access to each channel's full capabilities. Note that this doesn't
support starting several channels in synch.
[hskinnemoen@atmel.com: allocate platform device dynamically]
[hskinnemoen@atmel.com: Kconfig fix]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When possible, pass the tty name to request_irq() so that the user can easily
distinguish the different serial ports in /proc/interrupts.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by David Brownell, we really ought to be using container_of
when converting from "struct uart_port *" to "struct atmel_uart_port *".
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduced by atmel_serial-split-the-interrupt-handler.patch.
Thanks to michael <trimarchi@gandalf.sssup.it> for spotting it.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is based on the DMA-patch by Chip Coldwell for the AT91/AT32 serial
USARTS, with some tweaks to make it apply neatly on top of the other patches
in this series.
The RX and TX code has been moved to a tasklet and reworked a bit. Instead of
depending on the ENDRX and TIMEOUT bits in CSR, we simply grab as much data as
we can from the DMA buffers. I think this closes a race where the ENDRX bit
is set after we read CSR but before we read RPR, although I haven't confirmed
this.
Similarly, the two TX handlers (ENDTX and TXBUFE) have been combined into one.
Since the current code only uses a single TX buffer, there's no point in
handling those interrupts separately.
This also fixes a DMA sync bug in the original patch.
[linux@bohmer.net: rebased onto irq-splitup patch]
[hskinnemoen@atmel.com: moved to tasklet, fixed dma bug, misc cleanups]
[hskinnemoen@atmel.com: atmel_serial dma: Misc fixes and cleanups]
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split up the interrupt handler of the serial port into a interrupt top-half
and a tasklet.
The goal is to get the interrupt top-half as short as possible to minimize
latencies on interrupts. But the old code also does some calls in the
interrupt handler that are not allowed on preempt-RT in IRQF_NODELAY context.
This handler is executed in this context because of the interrupt sharing with
the timer interrupt. The timer interrupt on Preempt-RT runs in IRQF_NODELAY
context.
The tasklet takes care of handling control status changes, pushing incoming
characters to the tty layer, handling break and other errors. It also handles
pushing TX data into the data register.
Reading the complete receive queue is still done in the top-half because we
never want to miss any incoming character.
[hskinnemoen@atmel.com: misc cleanups and simplifications]
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an error happens in probe(), the clocks should be disabled, but
only if the port isn't already used as a console.
In remove(), the port struct shouldn't be freed because it's defined
statically.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If BRGR is zero, the baud rate generator isn't running, so the boot loader
can't have initialized the port.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace two instances of barrier() with cpu_relax() since that's the right
thing to do when busy-waiting. This does not actually change anything since
cpu_relax() is defined as barrier() on both ARM and AVR32.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the atmel_serial driver to conform the coding rules. It contains no
functional change.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From version 2.6 of the SMBIOS standard, type 10 (On Board Devices
Information) becomes obsolete. The reason for this is that no further
fields can be added to this structure without adversely affecting existing
software's ability to properly parse the data.
Therefore type 41 (Onboard Devices Extended Information) was added.
The structure is as follows:
struct smbios_type_41 {
u8 type;
u8 length;
u16 handle;
u8 reference_designation_string;
u8 device_type; /* same device type as in type 10 */
u8 device_type_instance;
u16 segment_group_number;
u8 bus_number;
u8 device_function_number;
};
For more info: http://www.dmtf.org/standards/smbios
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using "attr" twice is not OK, because it effectively prohibits such
container_of() on variables not named "attr".
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I guess aoedev_init() can go away now.
Cc: Greg KH <greg@kroah.com>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the year in the copyright notices.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton pointed out that the "too many targets" message in patch 2 could
be printed for failing GFP_ATOMIC allocations. This patch makes the messages
more specific.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The aoedev aoeminor member doesn't need a long format.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An AoE target provides an estimate of the number of outstanding commands that
the AoE initiator can send before getting a response. The aoe_maxout
parameter provides a way to set an even lower limit. It will not allow a user
to use more outstanding commands than the target permits. If a user discovers
a problem with a large setting, this parameter provides a way for us to work
with them to debug the problem. We expect to improve the dynamic window
sizing algorithm and drop this parameter. For the time being, it is a
debugging aid.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An aoe driver user who had about 70 AoE targets found that he was hitting a
BUG in sysfs_create_file because the aoe driver was trying to tell the kernel
about an AoE device more than once. Each AoE device was reachable by several
local network interfaces, and multiple ATA device indentify responses were
returning from that single device.
This patch eliminates a race condition so that aoe always informs the block
layer of a new AoE device once in the presence of multiple incoming ATA device
identify responses.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
What this Patch Does
Even before this recent series of 12 patches to 2.6.22-rc4, the aoe
driver was reusing a small set of skbs that were allocated once and
were only used for outbound AoE commands.
The network layer cannot be allowed to put_page on the data that is
still associated with a bio we haven't returned to the block layer,
so the aoe driver (even before the patch under discussion) is still
the owner of skbs that have been handed to the network layer for
transmission. We need to keep track of these skbs so that we can
free them, but by tracking them, we can also easily re-use them.
The new patch was a response to the behavior of certain network
drivers. We cannot reuse an skb that the network driver still has
in its transmit ring. Network drivers can defer transmit ring
cleanup and then use the state in the skb to determine how many data
segments to clean up in its transmit ring. The tg3 driver is one
driver that behaves in this way.
When the network driver defers cleanup of its transmit ring, the aoe
driver can find itself in a situation where it would like to send an
AoE command, and the AoE target is ready for more work, but the
network driver still has all of the pre-allocated skbs. In that
case, the new patch just calls alloc_skb, as you'd expect.
We don't want to get carried away, though. We try not to do
excessive allocation in the write path, so we cap the number of skbs
we dynamically allocate.
Probably calling it a "dynamic pool" is misleading. We were already
trying to use a small fixed-size set of pre-allocated skbs before
this patch, and this patch just provides a little headroom (with a
ceiling, though) to accomodate network drivers that hang onto skbs,
by allocating when needed. The d->skbpool_hd list of allocated skbs
is necessary so that we can free them later.
We didn't notice the need for this headroom until AoE targets got
fast enough.
Alternatives
If the network layer never did a put_page on the pages in the bio's
we get from the block layer, then it would be possible for us to
hand skbs to the network layer and forget about them, allowing the
network layer to free skbs itself (and thereby calling our own
skb->destructor callback function if we needed that). In that case
we could get rid of the pre-allocated skbs and also the
d->skbpool_hd, instead just calling alloc_skb every time we wanted
to transmit a packet. The slab allocator would effectively maintain
the list of skbs.
Besides a loss of CPU cache locality, the main concern with that
approach the danger that it would increase the likelihood of
deadlock when VM is trying to free pages by writing dirty data from
the page cache through the aoe driver out to persistent storage on
an AoE device. Right now we have a situation where we have
pre-allocation that corresponds to how much we use, which seems
ideal.
Of course, there's still the separate issue of receiving the packets
that tell us that a write has successfully completed on the AoE
target. When memory is low and VM is using AoE to flush dirty data
to free up pages, it would be perfect if there were a way for us to
register a fast callback that could recognize write command
completion responses. But I don't think the current problems with
the receive side of the situation are a justification for
exacerbating the problem on the transmit side.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an AoE device is detected, the kernel is informed, and a new block device
is created. If the device is unused, the block device corresponding to remote
device that is no longer available may be removed from the system by telling
the aoe driver to "flush" its list of devices.
Without this patch, software like GPFS and LVM may attempt to read from AoE
devices that were discovered earlier but are no longer present, blocking until
the I/O attempt times out.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adam Richter suggested eliminating this goto.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By returning unsigned long long, mac_addr does not generate compiler warnings
on 64-bit architectures.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A remote AoE device is something can process ATA commands and is identified by
an AoE shelf number and an AoE slot number. Such a device might have more
than one network interface, and it might be reachable by more than one local
network interface. This patch tracks the available network paths available to
each AoE device, allowing them to be used more efficiently.
Andrew Morton asked about the call to msleep_interruptible in the revalidate
function. Yes, if a signal is pending, then msleep_interruptible will not
return 0. That means we will not loop but will call aoenet_xmit with a NULL
skb, which is a noop. If the system is too low on memory or the aoe driver is
too low on frames, then the user can hit control-C to interrupt the attempt to
do a revalidate. I have added a comment to the code summarizing that.
Andrew Morton asked whether the allocation performed inside addtgt could use a
more relaxed allocation like GFP_KERNEL, but addtgt is called when the aoedev
lock has been locked with spin_lock_irqsave. It would be nice to allocate the
memory under fewer restrictions, but targets are only added when the device is
being discovered, and if the target can't be added right now, we can try again
in a minute when then next AoE config query broadcast goes out.
Andrew Morton pointed out that the "too many targets" message could be printed
for failing GFP_ATOMIC allocations. The last patch in this series makes the
messages more specific.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support direct_access XIP method with brd.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a rewrite of the ramdisk block device driver.
The old one is really difficult because it effectively implements a block
device which serves data out of its own buffer cache. It relies on the dirty
bit being set, to pin its backing store in cache, however there are non
trivial paths which can clear the dirty bit (eg. try_to_free_buffers()),
which had recently lead to data corruption. And in general it is completely
wrong for a block device driver to do this.
The new one is more like a regular block device driver. It has no idea about
vm/vfs stuff. It's backing store is similar to the buffer cache (a simple
radix-tree of pages), but it doesn't know anything about page cache (the pages
in the radix tree are not pagecache pages).
There is one slight downside -- direct block device access and filesystem
metadata access goes through an extra copy and gets stored in RAM twice.
However, this downside is only slight, because the real buffercache of the
device is now reclaimable (because we're not playing crazy games with it), so
under memory intensive situations, footprint should effectively be the same --
maybe even a slight advantage to the new driver because it can also reclaim
buffer heads.
The fact that it now goes through all the regular vm/fs paths makes it
much more useful for testing, too.
text data bss dec hex filename
2837 849 384 4070 fe6 drivers/block/rd.o
3528 371 12 3911 f47 drivers/block/brd.o
Text is larger, but data and bss are smaller, making total size smaller.
A few other nice things about it:
- Similar structure and layout to the new loop device handlinag.
- Dynamic ramdisk creation.
- Runtime flexible buffer head size (because it is no longer part of the
ramdisk code).
- Boot / load time flexible ramdisk size, which could easily be extended
to a per-ramdisk runtime changeable size (eg. with an ioctl).
- Can use highmem for the backing store.
[akpm@linux-foundation.org: fix build]
[byron.bbradley@gmail.com: make rd_size non-static]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net2280 can't have a function called show_registers() because this can produce
a namespace clash with an arch function of the same name.
All this driver's functions and variables should really be prefixed with
"net2280_" to avoid such a problem in future.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ayaz Abdulla