Commit graph

297 commits

Author SHA1 Message Date
Stefan Richter
a7b64b8704 firewire: Kconfig menu touch-up
Emphasize the recommendation to build only one stack.
Trim the prompts to better fit into short attention spans.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-06-19 00:12:35 +02:00
Stefan Richter
ae1e535579 firewire: deadline for PHY config transmission
If the low-level driver failed to initialize a card properly without
noticing it, fw-core was blocked indefinitely when trying to send a
PHY config packet.  This hung up the events kernel thread, e.g. locked
up keyboard input.
https://bugzilla.redhat.com/show_bug.cgi?id=444694
https://bugzilla.redhat.com/show_bug.cgi?id=446763

This problem was introduced between 2.6.25 and 2.6.26-rc1 by commit
2a0a259049 "firewire: wait until PHY
configuration packet was transmitted (fix bus reset loop)".

The solution is to wait with timeout.  I tested it with 7 different
working controllers and 1 non-working controller.  On the working ones,
the packet callback complete()s usually --- but not always --- before a
timeout of 10ms.  Hence I chose a safer timeout of 100ms.

On the few tests with the non-working controller ALi M5271, PHY config
packet transmission always timed out so far.  (Fw-ohci needs to be fixed
for this controller independently of this deadline fix.  Often the core
doesn't even attempt to send a phy config because not even self ID
reception works.)

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-06-19 00:12:35 +02:00
Stefan Richter
161b96e782 firewire: fw-ohci: unify printk prefixes
The messages which can be enabled by fw-ohci's debug module parameter
are changed from KERN_DEBUG to KERN_NOTICE level and uniformly prefixed
with "firewire_ohci: ".  This further simplifies communication with
users when we ask them to capture debug messages.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-06-19 00:12:35 +02:00
Stefan Richter
5cb84067d6 firewire: fill_bus_reset_event needs lock protection
Callers of fill_bus_reset_event() have to take card->lock.  Otherwise
access to node data may oops if node removal is in progress.

A lockless alternative would be

-	event->local_node_id = card->local_node->node_id;
+	tmp = fw_node_get(card->local_node);
+	event->local_node_id = tmp->node_id;
+	fw_node_put(tmp);

and ditto with the other node pointers which fill_bus_reset_event()
accesses.  But I went the locked route because one of the two callers
already holds the lock.  As a bonus, we don't need the memory barrier
anymore because device->generation and device->node_id are written in
a card->lock protected section.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
2008-06-19 00:12:35 +02:00
Stefan Richter
affc9c24ad firewire: fw-ohci: write selfIDBufferPtr before LinkControl.rcvSelfID
OHCI 1.1 clause 5.10 requires that selfIDBufferPtr is valid when a 1 is
written into LinkControl.rcvSelfID.

This driver bug has so far not been known to cause harm because most
chips obviously accept a later selfIDBufferPtr write, at least before
HCControl.linkEnable is written.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
2008-06-19 00:12:35 +02:00
Stefan Richter
e896ec4302 firewire: fw-ohci: disable PHY packet reception into AR context
We want the rcvPhyPkt bit in LinkControl off before we start using the
chip.  However, the spec says that the reset value of it is undefined.
Hence switch it explicitly off.

https://bugzilla.redhat.com/show_bug.cgi?id=244576#c48 shows that for
example the nForce2 integrated FireWire controller seems to have it on
by default.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-06-19 00:12:34 +02:00
Stefan Richter
ccff962943 firewire: fw-ohci: use of uninitialized data in AR handler
header_length and payload_length are filled with random data if an
unknown tcode was read from the AR buffer (i.e. if the AR buffer
contained invalid data).

We still need a better strategy to recover from this, but at least
handle_ar_packet now doesn't return out of bound buffer addresses
anymore.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-06-19 00:12:34 +02:00
Stefan Richter
0bf607c5b4 firewire: don't panic on invalid AR request buffer
BUG() at this place is wrong.  (Unless if the low level driver would
already do higher-level input validation of incoming request headers.)

Invalid incoming requests or bugs in the controller which corrupt the
AR-req buffer needlessly crashed the box because this is run in tasklet
context.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-06-19 00:12:34 +02:00
Jay Fenlason
551f4cb9de firewire: prevent userspace from accessing shut down devices
If userspace ignores the POLLERR bit from poll(), and only attempts to
read() the device when POLLIN is set, it can still make ioctl() calls on
a device that has been removed from the system.  The node_id and
generation returned by GET_INFO will be outdated, but INITIATE_BUS_RESET
would still cause a bus reset, and GET_CYCLE_TIMER will return data.
And if you guess the correct generation to use, you can send requests to
a different device on the bus, and get responses back.

This patch prevents open, ioctl, compat_ioctl, and mmap against shutdown
devices.

Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-05-20 18:24:17 +02:00
Linus Torvalds
d626e3bf72 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
  [SCSI] aic94xx: fix section mismatch
  [SCSI] u14-34f: Fix 32bit only problem
  [SCSI] dpt_i2o: sysfs code
  [SCSI] dpt_i2o: 64 bit support
  [SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt to dma_alloc_coherent
  [SCSI] dpt_i2o: use standard __init / __exit code
  [SCSI] megaraid_sas: fix suspend/resume sections
  [SCSI] aacraid: Add Power Management support
  [SCSI] aacraid: Fix jbod operations scan issues
  [SCSI] aacraid: Fix warning about macro side-effects
  [SCSI] add support for variable length extended commands
  [SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
  [SCSI] bsg: add large command support
  [SCSI] aacraid: Fix down_interruptible() to check the return value correctly
  [SCSI] megaraid_sas; Update the Version and Changelog
  [SCSI] ibmvscsi: Handle non SCSI error status
  [SCSI] bug fix for free list handling
  [SCSI] ipr: Rename ipr's state scsi host attribute to prevent collisions
  [SCSI] megaraid_mbox: fix Dell CERC firmware problem
2008-05-02 13:52:35 -07:00
Boaz Harrosh
64a87b244b [SCSI] Let scsi_cmnd->cmnd use request->cmd buffer
- struct scsi_cmnd had a 16 bytes command buffer of its own.
   This is an unnecessary duplication and copy of request's
   cmd. It is probably left overs from the time that scsi_cmnd
   could function without a request attached. So clean that up.

 - Once above is done, few places, apart from scsi-ml, needed
   adjustments due to changing the data type of scsi_cmnd->cmnd.

 - Lots of drivers still use MAX_COMMAND_SIZE. So I have left
   that #define but equate it to BLK_MAX_CDB. The way I see it
   and is reflected in the patch below is.
   MAX_COMMAND_SIZE - means: The longest fixed-length (*) SCSI CDB
                      as per the SCSI standard and is not related
                      to the implementation.
   BLK_MAX_CDB.     - The allocated space at the request level

 - I have audit all ISA drivers and made sure none use ->cmnd in a DMA
   Operation. Same audit was done by Andi Kleen.

(*)fixed-length here means commands that their size can be determined
   by their opcode and the CDB does not carry a length specifier, (unlike
   the VARIABLE_LENGTH_CMD(0x7f) command). This is actually not exactly
   true and the SCSI standard also defines extended commands and
   vendor specific commands that can be bigger than 16 bytes. The kernel
   will support these using the same infrastructure used for VARLEN CDB's.
   So in effect MAX_COMMAND_SIZE means the maximum size command
   scsi-ml supports without specifying a cmd_len by ULD's

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-05-02 10:18:22 -05:00
Linus Torvalds
886c35fbcf Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: fw-sbp2: log scsi_target ID at release
  ieee1394: fix NULL pointer dereference in sysfs access
2008-05-01 11:31:38 -07:00
Stefan Richter
f32ddaddf9 firewire: fw-sbp2: log scsi_target ID at release
Makes the good-by message more informative.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-05-01 19:55:24 +02:00
Matthew Wilcox
6188e10d38 Convert asm/semaphore.h users to linux/semaphore.h
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
2008-04-18 22:22:54 -04:00
Matthew Wilcox
d3135846f6 drivers: Remove unnecessary inclusions of asm/semaphore.h
None of these files use any of the functionality promised by
asm/semaphore.h.  It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
2008-04-18 22:16:32 -04:00
Adrian Bunk
db8be076ca firewire: cleanups
This patch contains the following cleanups:
- #if 0 the following unused structs:
  - fw-transaction.c:fw_low_memory_region
  - fw-transaction.c:fw_private_region
  - fw-transaction.c:fw_csr_region
  - fw-transaction.c:fw_unit_space_region
- remove the following unused EXPORT_SYMBOL's:
  - fw-card.c:fw_core_add_descriptor
  - fw-card.c:fw_core_remove_descriptor
  - fw-iso.c:fw_iso_context_create
  - fw-iso.c:fw_iso_context_destroy
  - fw-iso.c:fw_iso_context_start
  - fw-iso.c:fw_iso_context_queue
  - fw-iso.c:fw_iso_context_stop

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:37 +02:00
Stefan Richter
25b1c3d888 firewire: fix synchronization of gap counts
Fix:  The fact that nodes had different gap counts would be overlooked
if the bus manager code would pick gap count 63 because of beta
repeaters or because of very large hop counts.  In this case, the bus
manager code would miss that it actually has to send the PHY config
packet with gap count 63.

Related trivial changes:  Use bool for an int used as bool, touch up
some comments.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:36 +02:00
Stefan Richter
2a0a259049 firewire: wait until PHY configuration packet was transmitted (fix bus reset loop)
We now exit fw_send_phy_config /after/ the PHY config packet has been
transmitted, instead of before.  A subsequent fw_core_initiate_bus_reset
will therefore not overlap with the transmission.  This is meant to make
the send PHY config packet + reset bus routine more deterministic.

Fixes bus reset loop and eventual panic with
  - VIA VT6307 + IOGEAR hub + Unibrain Fire-i camera
    http://bugzilla.kernel.org/show_bug.cgi?id=10128
  - JMicron card

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:36 +02:00
Stefan Richter
e09770db0f firewire: remove unused struct member
request_generation is internal to fw-ohci and unneeded in fw_card.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:36 +02:00
Jarod Wilson
15f0d833f6 firewire: use bitwise and to get reg in handle_registers
for code efficiency.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:36 +02:00
Jarod Wilson
cca6097713 firewire: replace more hex values with defined csr constants
Trivial change to replace more meaningless (to the untrained eye) hex
values with defined CSR constants.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:36 +02:00
Stefan Richter
c9755e14a0 firewire: reread config ROM when device reset the bus
When a device changes its configuration ROM, it announces this with a
bus reset.  firewire-core has to check which node initiated a bus reset
and whether any unit directories went away or were added on this node.

Tested with an IOI FWB-IDE01AB which has its link-on bit set if bus
power is available but does not respond to ROM read requests if self
power is off.  This implements
  - recognition of the units if self power is switched on after fw-core
    gave up the initial attempt to read the config ROM,
  - shutdown of the units when self power is switched off.

Also tested with a second PC running Linux/ieee1394.  When the eth1394
driver is inserted and removed on that node, fw-core now notices the
addition and removal of the IPv4 unit on the ieee1394 node.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:36 +02:00
Stefan Richter
1dadff71d6 firewire: replace static ROM cache by allocated cache
read_bus_info_block() is repeatedly called by workqueue jobs.
These will step on each others toes eventually if there are multiple
workqueue threads, and we end up with corrupt config ROM images.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:35 +02:00
Stefan Richter
d34316a4bd firewire: fw-ohci: work around generation bug in TI controllers (fix AV/C and more)
Unlike the ohci1394 driver, fw-ohci uses the selfIDGeneration field of
bus reset packets to determine the generation of incoming requests as
per OHCI 1.1 clause 8.4.2.3.  This is more precise --- provided that the
controller inserts the correct generation.  Texas Instruments chips
often don't.

This prevented the transmission of response packets, which for example
broke AV/C transactions as used when communicating with miniDV cameras
and any other AV/C devices.

There is apparently no way to detect and adjust incorrect generations.
Therefore we ignore the generation of bus reset packets from TI chips
and use the generation of the self ID buffer instead.  Alas this is
received at a slightly wrong time.  In rare cases, this could cause us
to not respond to legitimate requests or to respond to expired requests.
(The latter is less likely because the bus reset packet AR event is
typically handled before the self ID complete event.)

Bug reported by Mladen Kuntner, who was extraordinarily patient while
dealing with the driver maintainers.  Fix confirmed to be required and
effective for TSB82AA2 and a TSB43AB22 or TSB43AB22A.
https://bugzilla.redhat.com/show_bug.cgi?id=243081

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:35 +02:00
Stefan Richter
08ddb2f4c2 firewire: fw-ohci: extend logging of bus generations and node ID
Extend the logging of "AR evt_bus_reset, link internal" to "AR
evt_bus_reset, generation ${selfIDGeneration}".  That way we can check
whether this generation matches the one seen in self ID complete event
logging.  See OHCI 1.1 clause 8.4.2.3.

Also extend logging of "firewire_ohci: * selfIDs, generation *" by
"local node ID ffc*" in self ID logging to make the local node in AT/AR
event logs more obvious.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:35 +02:00
Stefan Richter
a007bb857e firewire: fw-ohci: conditionally log busReset interrupts
Add a debug option to watch bus reset interrupt events.  Half of this
patch is taken from Jarod Wilson's first version of the JMicron fix.

BusReset interrupts are only generated if the respective module
parameter flag was set before the controller is being initialized.
Else we keep this event masked to reduce IRQ load in normal operation
and to avoid potential problems with buggy chips.

Note, this is unlike the other IRQ events whose logging can be enabled
any time after chip initialization.  This and the influence on what
interrupts the chip generates is why I added an extra flag for it.

Also, reorder the debug parameter flags according to their perceived
usefulness.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:35 +02:00
Jarod Wilson
76f73ca1b2 firewire: fw-ohci: don't append to AT context when it's not active
I finally tracked down the issues with this JMicron PCI-e card in my
possession to a failure to comply with section 7.2.3.2 of the OHCI 1.1
specification (thanks to Kristian for the pointer to illustrate that it
is indeed a flaw in this card, not the driver). The controller should
simply flush the packets we've appended to its AT queue if a bus reset
occurs before they've been transmitted and we'll try again, but
something goes wrong and the controller winds up hung.

However, we can avoid the problem by simply checking if the
IntEvent.busReset register had been set before we try appending to the
AT context. When busReset is set, the AT context is completely halted
until busReset is cleared, so there's no point in appending AT packets
until the register is cleared. So at_context_queue_packet() now checks
for busReset being set, and bails with an RCODE_GENERATION packet ack,
which results in us trying to append the packet again after recognizing
the fact there has been a bus reset, and clearing busReset.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:35 +02:00
Jarod Wilson
75f7832e3b firewire: fw-ohci: log regAccessFail events
While trying to debug this piece of crap JMicron PCI-e controller in my
possession, one thought was that perhaps I was encountering register access
failures. I'm not, but logging them would be good, so we can see if they
are a real problem we should be taking into account anywhere in the code.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added list contact)
2008-04-18 17:55:34 +02:00
Jarod Wilson
022147242f firewire: fw-ohci: make sure HCControl register LPS bit is set
I've now witnessed multiple occasions where one of my controllers (a very
poorly working JMicron PCIe card) fails to get its registers properly set
up in ohci_enable(), apparently due to an occasionally very slow to
initiate SClk. The easy fix for this problem is to add a tiny while loop
to try again a time or three after initially enabling LPS before we
move on (or give up).

Of course, the card still isn't fully functional yet, but this gets it at
least one tiny step closer...

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:34 +02:00
Stefan Richter
130d5496e2 firewire: fw-ohci: missing PPC PMac feature calls in failure path
Balance ohci_pmac_on and ohci_pmac_off if pci_driver.probe fails.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:34 +02:00
Stefan Richter
43286568ad firewire: fw-ohci: untangle a mixed unsigned/signed expression
and make another expression more readable.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:34 +02:00
Stefan Richter
ad3c0fe8b8 firewire: debug interrupt events
This adds debug printks for asynchronous transmission and reception and
for self ID reception.  They can be enabled at module load time, and at
runtime via /sys/module/firewire_ohci/parameters/debug.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>

Also added:  Logging of interrupt event codes and of cancelled AT
packets.

The code now depends on a Kconfig variable.  This makes it easier to
build firewire-ohci without the feature or to make it an option in the
future.  The variable is currently hidden and always on.

This feature inflates firewire-ohci.ko by 7 kB = 27% on x86-64 and by
4 kB = 23% on i686.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:34 +02:00
Stefan Richter
016bf3dfcf firewire: fw-ohci: catch self_id_count == 0
fw_core_handle_bus_reset() incorrectly relied on the assumption that
self_id_count > 0.

We check early in fw-ohci and discard the self ID complete event if
self_id_count == 0 because a valid event always has at least one self ID
packet in it (the one of the local node).  Hence treat self_id_count ==
0 like any other kind of invalid self ID buffer.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:34 +02:00
Stefan Richter
c8a9a498e1 firewire: fw-ohci: add self ID error check
Discard self ID buffer contents if
  - the selfIDError flag is set,
  - any of the self ID packets has bit errors.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:33 +02:00
Stefan Richter
2ed0f181f0 firewire: fw-ohci: refactor probe, remove, suspend, resume
Clean up shared code and variable names.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:33 +02:00
Stefan Richter
eb5ca72eff firewire: fw-ohci: switch on bus power after resume on PPC PMac
The platform feature calls in the suspend method switched off cable
power, but the calls in the resume method did not switch it back on.

Add the necessary feature call to .resume.  Also add the corresponding
call to .suspend to make .suspend's behavior explicitly the same on all
PMacs.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:33 +02:00
Stefan Richter
080de8c2c5 firewire: fw-ohci: add option for remote debugging
This way firewire-ohci can be used for remote debugging like ohci1394.
Version with amendment from Fri, 11 Apr 2008 00:08:08 +0200.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Bernhard Kaindl <bk@suse.de>
2008-04-18 17:55:33 +02:00
Jarod Wilson
17cff9ff87 firewire: fw-sbp2: set dual-phase cycle_limit
Try to write dual-phase retry protocol limits to BUSY_TIMEOUT register.
- The dual-phase retry protocol is optional to implement, and if not 
  supported, writes to the dual-phase portion of the register will be
  ignored. We try to write the original 1394-1995 default here.
- In the case of devices that are also SBP-3-compliant, all writes are 
  ignored, as the register is read-only, but contains single-phase retry of
  15, which is what we're trying to set for all SBP-2 device anyway, so this
  write attempt is safe and yields more consistent behavior for all devices.

See section 8.3.2.3.5 of the 1394-1995 spec, section 6.2 of the SBP-2 spec,
and section 6.4 of the SBP-3 spec for further details.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:33 +02:00
Stefan Richter
a5fd9ec7a2 firewire: fw-sbp2: reduce log noise
The block/unblock logic is now sufficiently tested.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
6f73100cbb firewire: fw-sbp2: remove unnecessary memset
orb came from kzalloc.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
0d7dcbf2a3 firewire: fw-sbp2: simplify some macros
How hard can it be to switch on one bit? :-)

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
71ee9f01f2 firewire: fw-sbp2: remove usages of fw_memcpy_to_be32
Write directly in big endian instead of byte-swapping after the fact.
This saves a few conversions, lets gcc use constant endianess
conversions where possible, and enables deeper endianess annotation.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
8ac3a47cab firewire: fw-sbp2: relax SCSI DMA alignment
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-04-18 17:55:32 +02:00
Stefan Richter
1dc3bea78b firewire: refactor fw_unit reference counting
Add wrappers for getting and putting a unit.
Remove some line breaks.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:32 +02:00
Stefan Richter
7c1fca3366 firewire: fw-sbp2: fix reference counting
The reference count of the unit dropped too low in an error path in
sbp2_probe.  Fixed by moving the _get further up.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:31 +02:00
Stefan Richter
bd7dee6311 firewire: remove superfluous reference counting
The card->kref became obsolete since patch "firewire: fix crash in
automatic module unloading" added another counter of card users.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-04-18 17:55:31 +02:00
Jarod Wilson
6b84236d37 firewire: fw-ohci: plug dma memory leak in AR handler
There's an ugly little memory leak in firewire-ohci's
ar_context_tasklet(), where we're not freeing up some of the memory we
use for each ar_buffer, due to a moving pointer. The problem has been
there for a while, but didn't get noticed until after converting the AR
routines over to use coherent DMA and I started running into I/O stall-
outs with the following message output repeatedly to the console:

PCI-DMA: Out of IOMMU space for 53248 bytes at device 0000:04:09.0

Plugging this leak is definitely necessary, but unfortunately, isn't the
entire answer to my problem, it only increases the amount of I/O that I
can do before hitting the problem. Still working on tracking down the
root cause..

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-03-27 21:01:14 +01:00
Stefan Richter
10a4c73551 firewire: fix panic in handle_at_packet
This fixes a use-after-free bug in the handling of split transactions.
The AT DMA handler of the request was occasionally executed after the
AR DMA handler of the response.  The AT DMA handler then accessed an
already freed packet.

Reported by Johannes Berg.
http://bugzilla.kernel.org/show_bug.cgi?id=9617

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jarod Wilson <jwilson@redhat.com>
2008-03-20 18:13:05 +01:00
Stefan Richter
f5101d58af firewire: fw-ohci: shut up false compiler warning on PPC32
Shut up "may be used uninitialised in this function" warnings due to
PPC32's implementation of dma_alloc_coherent().

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-03-14 00:57:00 +01:00
Jarod Wilson
bde1709aaa firewire: fw-ohci: use dma_alloc_coherent for ar_buffer
Currently, we do nothing to guarantee we have a consistent DMA buffer for
asynchronous receive packets. Rather than doing several sync's following a
dma_map_single() to get consistent buffers, just switch to using
dma_alloc_coherent().

Resolves constant buffer failures on my own x86_64 laptop w/4GB of RAM and
likely to fix a number of other failures witnessed on x86_64 systems with
4GB of RAM or more.

Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
2008-03-14 00:57:00 +01:00