Commit graph

843 commits

Author SHA1 Message Date
NeilBrown
dfc7064500 md: restart recovery cleanly after device failure.
When we get any IO error during a recovery (rebuilding a spare), we abort
the recovery and restart it.

For RAID6 (and multi-drive RAID1) it may not be best to restart at the
beginning: when multiple failures can be tolerated, the recovery may be
able to continue and re-doing all that has already been done doesn't make
sense.

We already have the infrastructure to record where a recovery is up to
and restart from there, but it is not being used properly.
This is because:
  - We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR,
    which causes the recovery not be be checkpointed.
  - We remove spares and then re-added them which loses important state
    information.

The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't
needed.  If there is an error, the relevant drive will be marked as
Faulty, and that is enough to ensure correct handling of the error.  So we
first remove MD_RECOVERY_ERR, changing some of the uses of it to
MD_RECOVERY_INTR.

Then we cause the attempt to remove a non-faulty device from an array to
fail (unless recovery is impossible as the array is too degraded).  Then
when remove_and_add_spares attempts to remove the devices on which
recovery can continue, it will fail, they will remain in place, and
recovery will continue on them as desired.

Issue:  If we are halfway through rebuilding a spare and another drive
fails, and a new spare is immediately available,  do we want to:
 1/ complete the current rebuild, then go back and rebuild the new spare or
 2/ restart the rebuild from the start and rebuild both devices in
    parallel.

Both options can be argued for.  The code currently takes option 2 as
  a/ this requires least code change
  b/ this results in a minimally-degraded array in minimal time.

Cc: "Eivind Sarto" <ivan@kasenna.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:10 -07:00
Bernd Schubert
90b08710e4 md: allow parallel resync of md-devices.
In some configurations, a raid6 resync can be limited by CPU speed
(Calculating P and Q and moving data) rather than by device speed.  In
these cases there is nothing to be gained byt serialising resync of arrays
that share a device, and doing the resync in parallel can provide benefit.
 So add a sysfs tunable to flag an array as being allowed to resync in
parallel with other arrays that use (a different part of) the same device.

Signed-off-by: Bernd Schubert <bs@q-leap.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:10 -07:00
Dan Williams
4f54b0e948 md: notify userspace on 'stop' events
This additional notification to 'array_state' is needed to allow the
monitor application to learn about stop events via sysfs.  The
sysfs_notify("sync_action") call that comes at the end of do_md_stop()
(via md_new_event) is insufficient since the 'sync_action' attribute has
been removed by this point.

(Seems like a sysfs-notify-on-removal patch is a better fix.  Currently
removal updates the event count but does not wake up waiters)

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:10 -07:00
NeilBrown
09a44cc150 md: notify userspace on 'write-pending' changes to array_state
When an array enters write pending, 'array_state' changes, so we must be
sure to sysfs_notify.

Also, when waiting for user-space to acknowledge 'write-pending' by
marking the metadata as dirty, we don't want to wait for MD_CHANGE_DEVS to
be cleared as that might not happen.  So explicity test for the bits that
we are really interested in.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:10 -07:00
NeilBrown
698b18c1e8 md: raid1: Fix restoration of bio between failed read and write.
When performing a "recovery" or "check" pass on a RAID1 array, we read
from each device and possible, if there is a difference or a read error,
write back to some devices.

We use the same 'bio' for both read and write, resetting various fields
between the two operations.

We forgot to reset bv_offset and bv_len however.  These are often left
unchanged, but in the case where there is an IO error one or two sectors
into a page, they are changed.

This results in correctable errors not being corrected properly.  It does
not result in any data corruption.

Cc: "Fairbanks, David" <David.Fairbanks@stratus.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:10 -07:00
Bernd Schubert
6be9d49401 md: md: raid5 rate limit error printk
Last night we had scsi problems and a hardware raid unit was offlined
during heavy i/o.  While this happened we got for about 3 minutes a huge
number messages like these

Apr 12 03:36:07 pfs1n14 kernel: [197510.696595] raid5:md7: read error not correctable (sector 2993096568 on sdj2).

I guess the high error rate is responsible for not scheduling other events
- during this time the system was not pingable and in the end also other
devices run into scsi command timeouts causing problems on these unrelated
devices as well.

Signed-off-by: Bernd Schubert <bernd-schubert@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:10 -07:00
Christoph Hellwig
6bcfd60186 md: kill file_path wrapper
Kill the trivial and rather pointless file_path wrapper around d_path.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:09 -07:00
NeilBrown
84255d1018 md: fix possible oops when removing a bitmap from an active array
It is possible to add a write-intent bitmap to an active array, or remove
the bitmap that is there.

When we do with the 'quiesce' the array, which causes make_request to
block in "wait_barrier()".

However we are sampling the value of "mddev->bitmap" before the
wait_barrier call, and using it afterwards.  This can result in using a
bitmap structure that has been freed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-24 09:56:09 -07:00
Neil Brown
e7e72bf641 Remove blkdev warning triggered by using md
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.

For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock.  So always initialise that lock when allocated.

With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.

Thanks to Dan Williams for review and fixing the silly bugs.

Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nick Piggin <npiggin@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Cc: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-14 19:11:15 -07:00
Dan Williams
c8894419ac md: fix raid5 'repair' operations
commit bd2ab67030 "md: close a livelock window
in handle_parity_checks5" introduced a bug in handling 'repair' operations.
After a repair operation completes we clear the state bits tracking this
operation.  However, they are cleared too early and this results in the code
deciding to re-run the parity check operation.  Since we have done the repair
in memory the second check does not find a mismatch and thus does not do a
writeback.

Test results:
$ echo repair > /sys/block/md0/md/sync_action
$ cat /sys/block/md0/md/mismatch_cnt
51072
$ echo repair > /sys/block/md0/md/sync_action
$ cat /sys/block/md0/md/mismatch_cnt
0

(also fix incorrect indentation)

Cc: <stable@kernel.org>
Tested-by: George Spelvin <linux@horizon.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-13 08:02:24 -07:00
Harvey Harrison
cb6969e8cd misc: fix integer as NULL pointer warnings
drivers/md/raid10.c:889:17: warning: Using plain integer as NULL pointer
drivers/media/video/cx18/cx18-driver.c:616:12: warning: Using plain integer as NULL pointer
sound/oss/kahlua.c:70:12: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-05-08 10:46:55 -07:00
Dan Williams
6bfe0b4990 md: support blocking writes to an array on device failure
Allows a userspace metadata handler to take action upon detecting a device
failure.

Based on an original patch by Neil Brown.

Changes:
-added blocked_wait waitqueue to rdev
-don't qualify Blocked with Faulty always let userspace block writes
-added md_wait_for_blocked_rdev to wait for the block device to be clear, if
 userspace misses the notification another one is sent every 5 seconds
-set MD_RECOVERY_NEEDED after clearing "blocked"
-kill DoBlock flag, just test mddev->external

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:33 -07:00
Dan Williams
11e2ede022 md: prevent duplicates in bind_rdev_to_array
Found when trying to reassemble an active externally managed array.  Without
this check we hit the more noisy "sysfs duplicate" warning in the later call
to kobject_add.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:33 -07:00
Dan Williams
242b363e22 md: remove a stray command from a copy and paste error in resync_start_store
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:33 -07:00
NeilBrown
648b629ed4 md: fix up switching md arrays between read-only and read-write
When setting an array to 'readonly' or to 'active' via sysfs, we must make the
appropriate set_disk_ro call too.

Also when switching to "read_auto" (which is like readonly, but blocks on the
first write so that metadata can be marked 'dirty') we need to be more careful
about what state we are changing from.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:32 -07:00
NeilBrown
31a59e3425 md: fix 'safemode' handling for external metadata.
'safemode' relates to marking an array as 'clean' if there has been no write
traffic for a while (a couple of seconds), to reduce the chance of the array
being found dirty on reboot.

->safemode is set to '1' when there have been no write for a while, and it
gets set to '0' when the superblock is updates with the 'clean' flag set.

This requires a few fixes for 'external' metadata:
 - When an array is set to 'clean' via sysfs, 'safemode' must be cleared.
 - when we write to an array that has 'safemode' set (there must have been
        some delay in updating the metadata), we need to clear safemode.
 - Don't try to update external metadata in md_check_recovery for safemode
        transitions - it won't work.

Also, don't try to support "immediate safe mode" (safemode==2) for external
metadata, it cannot really work (the safemode timeout can be set very low if
this is really needed).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:32 -07:00
NeilBrown
d897dbf914 md: reinitialise more mddev fields in do_md_stop.
I keep finding problems where an mddev gets reused and some fields has a value
from a previous usage that confuses the new usage.  So clear all fields that
could possible need clearing when calling do_md_stop.

Also initialise the 'level' of a new array to LEVEL_NONE (which isn't 0).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:32 -07:00
NeilBrown
8377bc8080 md: skip all metadata update processing when using external metadata.
All the metadata update processing for external metadata is on in user-space
or through the sysfs interfaces, so make "md_update_sb" a no-op in that case.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:32 -07:00
Dan Williams
6a51830e14 md: fix use after free when removing rdev via sysfs
rdev->mddev is no longer valid upon return from entry->store() when the
'remove' command is given.

Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-30 08:29:32 -07:00
Jens Axboe
c9a3f6d6f5 dm: use unlocked variants of queue flag check/set
dm.c already provides mutual exclusion through ->map_lock.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-29 10:21:12 -07:00
Linus Torvalds
bd5d435a96 Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: Skip I/O merges when disabled
  block: add large command support
  block: replace sizeof(rq->cmd) with BLK_MAX_CDB
  ide: use blk_rq_init() to initialize the request
  block: use blk_rq_init() to initialize the request
  block: rename and export rq_init()
  block: no need to initialize rq->cmd with blk_get_request
  block: no need to initialize rq->cmd in prepare_flush_fn hook
  block/blk-barrier.c:blk_ordered_cur_seq() mustn't be inline
  block/elevator.c:elv_rq_merge_ok() mustn't be inline
  block: make queue flags non-atomic
  block: add dma alignment and padding support to blk_rq_map_kern
  unexport blk_max_pfn
  ps3disk: Remove superfluous cast
  block: make rq_init() do a full memset()
  relay: fix splice problem
2008-04-29 08:18:03 -07:00
Denis V. Lunev
c7705f3449 drivers: use non-racy method for proc entries creation (2)
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.

Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-29 08:06:22 -07:00
FUJITA Tomonori
992b5bceee block: no need to initialize rq->cmd with blk_get_request
blk_get_request initializes rq->cmd (rq_init does) so the users don't
need to do that.

The purpose of this patch is to remove sizeof(rq->cmd) and &rq->cmd,
as a preparation for large command support, which changes rq->cmd from
the static array to a pointer. sizeof(rq->cmd) will not make sense and
&rq->cmd won't work.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-04-29 14:48:55 +02:00
Nick Piggin
75ad23bc0f block: make queue flags non-atomic
We can save some atomic ops in the IO path, if we clearly define
the rules of how to modify the queue flags.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-04-29 14:48:33 +02:00
Julia Lawall
62b0559aad drivers/md: use time_before, time_before_eq, etc
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.

A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@ change_compare_np @
expression E;
@@

(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)

@ include depends on change_compare_np @
@@

#include <linux/jiffies.h>

@ no_include depends on !include && change_compare_np @
@@

  #include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:42 -07:00
Nick Andrew
d7a420c947 raid: remove leading TAB on printk messages
MD drivers use one printk() call to print 2 log messages and the second line
may be prefixed by a TAB character.  It may also output a trailing space
before newline.  klogd (I think) turns the TAB character into the 2 characters
'^I' when logging to a file.  This looks ugly.

Instead of a leading TAB to indicate continuation, prefix both output lines
with 'raid:' or similar.  Also remove any trailing space in the vicinity of
the affected code and consistently end the sentences with a period.

Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:42 -07:00
Dan Williams
4ef197d87a md: raid5.c convert simple_strtoul to strict_strtoul
strict_strtoul handles the open-coded sanity checks in
raid5_store_stripe_cache_size and raid5_store_preread_threshold

Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:42 -07:00
Dan Williams
8b3e6cdc53 md: introduce get_priority_stripe() to improve raid456 write performance
Improve write performance by preventing the delayed_list from dumping all its
stripes onto the handle_list in one shot.  Delayed stripes are now further
delayed by being held on the 'hold_list'.  The 'hold_list' is bypassed when:

  * a STRIPE_IO_STARTED stripe is found at the head of 'handle_list'
  * 'handle_list' is empty and i/o is being done to satisfy full stripe-width
    write requests
  * 'bypass_count' is less than 'bypass_threshold'.  By default the threshold
    is 1, i.e. every other stripe handled is a preread stripe provided the
    top two conditions are false.

Benchmark data:
System: 2x Xeon 5150, 4x SATA, mem=1GB
Baseline: 2.6.24-rc7
Configuration: mdadm --create /dev/md0 /dev/sd[b-e] -n 4 -l 5 --assume-clean
Test1: dd if=/dev/zero of=/dev/md0 bs=1024k count=2048
  * patched:  +33% (stripe_cache_size = 256), +25% (stripe_cache_size = 512)

Test2: tiobench --size 2048 --numruns 5 --block 4096 --block 131072 (XFS)
  * patched: +13%
  * patched + preread_bypass_threshold = 0: +37%

Changes since v1:
* reduce bypass_threshold from (chunk_size / sectors_per_chunk) to (1) and
  make it configurable.  This defaults to fairness and modest performance
  gains out of the box.
Changes since v2:
* [neilb@suse.de]: kill STRIPE_PRIO_HI and preread_needed as they are not
  necessary, the important change was clearing STRIPE_DELAYED in
  add_stripe_bio and this has been moved out to make_request for the hang
  fix.
* [neilb@suse.de]: simplify get_priority_stripe
* [dan.j.williams@intel.com]: reset the bypass_count when ->hold_list is
  sampled empty (+11%)
* [dan.j.williams@intel.com]: decrement the bypass_count at the detection
  of stripes being naturally promoted off of hold_list +2%.  Note, resetting
  bypass_count instead of decrementing on these events yields +4% but that is
  probably too aggressive.
Changes since v3:
* cosmetic fixups

Tested-by: James W. Laferriere <babydr@baby-dragons.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:42 -07:00
Harvey Harrison
e46b272b66 md: replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:42 -07:00
Harvey Harrison
9a7b2b0f36 md: fix integer as NULL pointer warnings in md.c
drivers/md/md.c:734:16: warning: Using plain integer as NULL pointer
drivers/md/md.c:1115:16: warning: Using plain integer as NULL pointer

Add some braces to match the else-block as well.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:42 -07:00
Frederik Deweerdt
cf13ab8e02 dm: remove md argument from specific_minor
The small patch below:
- Removes the unused md argument from both specific_minor() and next_free_minor()
- Folds kmalloc + memset(0) into a single kzalloc call in alloc_dev()

This has been compile tested on x86.

Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:27:02 +01:00
Adrian Bunk
4fdfe401e9 dm table: remove unused dm_create_error_table
dm_create_error_table() was added in kernel 2.6.18 and never used...

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:27:00 +01:00
Adrian Bunk
e8488d0858 dm table: drop void suspend_targets return
void returning functions returned the return value of another void
returning function...

Spotted by sparse.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:59 +01:00
Mikulas Patocka
7ff14a3615 dm: unplug queues in threads
Remove an avoidable 3ms delay on some dm-raid1 and kcopyd I/O.

It is specified that any submitted bio without BIO_RW_SYNC flag may plug the
queue (i.e. block the requests from being dispatched to the physical device).

The queue is unplugged when the caller calls blk_unplug() function. Usually, the
sequence is that someone calls submit_bh to submit IO on a buffer. The IO plugs
the queue and waits (to be possibly joined with other adjacent bios). Then, when
the caller calls wait_on_buffer(), it unplugs the queue and submits the IOs to
the disk.

This was happenning:

When doing O_SYNC writes, function fsync_buffers_list() submits a list of
bios to dm_raid1, the bios are added to dm_raid1 write queue and kmirrord is
woken up.

fsync_buffers_list() calls wait_on_buffer().  That unplugs the queue, but
there are no bios on the device queue as they are still in the dm_raid1 queue.

wait_on_buffer() starts waiting until the IO is finished.

kmirrord is scheduled, kmirrord takes bios and submits them to the devices.

The submitted bio plugs the harddisk queue but there is no one to unplug it.
(The process that called wait_on_buffer() is already sleeping.)

So there is a 3ms timeout, after which the queues on the harddisks are
unplugged and requests are processed.

This 3ms timeout meant that in certain workloads (e.g. O_SYNC, 8kb writes),
dm-raid1 is 10 times slower than md raid1.

Every time we submit something asynchronously via dm_io, we must unplug the
queue actually to send the request to the device.

This patch adds an unplug call to kmirrord - while processing requests, it keeps
the queue plugged (so that adjacent bios can be merged); when it finishes
processing all the bios, it unplugs the queue to submit the bios.

It also fixes kcopyd which has the same potential problem. All kcopyd requests
are submitted with BIO_RW_SYNC.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
2008-04-25 13:26:57 +01:00
Mikulas Patocka
a2aebe03be dm raid1: use timer
This patch replaces the schedule() in the main kmirrord thread with a timer.
The schedule() could introduce an unwanted delay when work is ready to be
processed.

The code instead calls wake() when there's work to be done immediately, and
delayed_wake() after a failure to give a short delay before retrying.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:56 +01:00
Alasdair G Kergon
a765e20eeb dm: move include files
Publish the dm-io, dm-log and dm-kcopyd headers in include/linux.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:55 +01:00
Alasdair G Kergon
2d1e580afe dm kcopyd: rename
Rename kcopyd.[ch] to dm-kcopyd.[ch].

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:54 +01:00
Alasdair G Kergon
0da336e5fa dm: expose macros
Make dm.h macros and inlines available in include/linux/device-mapper.h

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:53 +01:00
Mikulas Patocka
945fa4d283 dm kcopyd: remove redundant client counting
Remove client counting code that is no longer needed.

Initialization and destruction is made globally from dm_init and dm_exit and is
not based on client counts. Initialization allocates only one empty slab cache,
so there is no negative impact from performing the initialization always,
regardless of whether some client uses kcopyd or not.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:52 +01:00
Mikulas Patocka
08d8757a4d dm kcopyd: private mempool
Change the global mempool in kcopyd into a per-device mempool to avoid
deadlock possibilities.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:50 +01:00
Mikulas Patocka
8c0cbc2f79 dm kcopyd: per device
Make one kcopyd thread per device.

The original shared kcopyd could deadlock.

Configuration:
2008-04-25 13:26:49 +01:00
Jonathan Brassow
2a23aa1ddb dm log: make module use tracking internal
Remove internal module reference fields from the interface.

Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:48 +01:00
Alasdair G Kergon
b8206bc3de dm log: move register functions
Reorder a couple of functions in the file so the next patch is readable.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:47 +01:00
Heinz Mauelshagen
416cd17b19 dm log: clean interface
Clean up the dm-log interface to prepare for publishing it in include/linux.

Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:46 +01:00
Heinz Mauelshagen
eb69aca5d3 dm kcopyd: clean interface
Clean up the kcopyd interface to prepare for publishing it in include/linux.

Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:44 +01:00
Heinz Mauelshagen
22a1ceb1e6 dm io: clean interface
Clean up the dm-io interface to prepare for publishing it in include/linux.

Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:43 +01:00
Alasdair G Kergon
e01fd7eeb0 dm io: rename error to error_bits
Rename 'error' to 'error_bits' for clarity.

Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:41 +01:00
Mikulas Patocka
72727bad54 dm snapshot: store pointer to target instance
Save pointer to dm_target in dm_snapshot structure.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:40 +01:00
Heinz Mauelshagen
769aef30f0 dm log: move dirty region log code into separate module
Move the dirty region log code into a separate module so
other targets can share the code.

Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:39 +01:00
Heinz Mauelshagen
b7fd54a70f dm log: generalise name in messages
Change dm-log.c messages from "mirror log" to "dirty region log" as
a new dm target wants to share this code.

Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2008-04-25 13:26:38 +01:00