This patch inhibits sending spi negotiation parameters
for non-configured devices from the slave_destroy function.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ioc->alt_ioc->alt_ioc pointer is not getting cleared
during driver unload time. This dangling pointer
can result in panic in certain circumstances, such
as error recovery, or firmware download in flashless
environments. This only impacts dual functions controllers,
such as 1030. Please apply.
This patch also includes a small cosmetic name change
for mpt_spi_log_info.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When people use the userspace scanning facilities on SAS hardware the
LLDD gets bogus slave_alloc calls. Just fail those gracefully instead
of printing a warning in mptsas and another one in the midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding verbose message returned from firmware
when a task mangment request fails.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, Jan 16, 2006 at 06:53:24PM -0700, Moore, Eric wrote:
> Adding MSI support, and command line for enabling
> it. By default, the command line option has MSI disabled.
mpt_msi_enable is initialized to 0 implicitly, no need to do that. Also
replace if (mpt_msi_enable == 1) tests with just if (mpt_msi_enable).
Updated patch below:
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A customer request to send raid asyn actions
from firmware to the event syslog. This shows
when raid volumes go degraded, or complete resync,
or volumes created/deleted, etc.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Increasing the reply frame size by 16 bytes, to
be in sync with the other fusion drivers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, Jan 16, 2006 at 06:53:13PM -0700, Moore, Eric wrote:
> The task managment request timeout in the eh threads was set
> for U320 timing, which is between 2-5 seconds.
> This is too small for FC and SAS.
> According to the firmware engineers, Fibre needs to be 40 seconds
> and SAS needs to be 10 seconds.
The timeout selection should probably be done in a little helper instead
of duplicated in a few places. Updated patch below.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Increase the port enable timeout only for SAS from 30 to 300 seconds.
A customer request for the handling large topologies.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is for spi. This issues bus reset when driver
loads. Handling cases when initator has negotiated for packetized,
and target negotiated for non-packetized; effectly this bus reset
is getting both target and initiator on the same sheet of music.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix the timer handling in aic79xx to use the SCSI-ML provided handling
instead of implementing our own.
It also fixes a deadlock in the command recovery code.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the aic79xx sequencer with latest fixes from adaptec.
The sequencer code now corresponds with adaptec version 2.0.15.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The prior fusion patches moved an invocation of a function,
mptscsih_TMHandler(), static to mptscsih.c into mptsas.c
Make the function unstatic, move the header to mptscsih.h and export it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fix's problems with recent fc submission regarding
i/o being redirected to the wrong target.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This moves code intented for SAS from
the generic mptscsih module over to the
mptsas module.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The issuing of the target reset
used in device hot removal case so the
firmware queue is flushed out off outstanding
commands.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
RAID event support.
This will hot add and remove raid volumes
when managment application creates and
deletes the volumes. The driver is basically
responding to firmware asyn events, and reporting
the changes to the above layers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch displays the port identifier on
the folder attribute; located in the middle digit.
/sys/class/sas_rphy/rphy-%x:%x:%x
The port identifier is basically the unique identifier
for each sas domain.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch defines a new template to represent each type of
controllers (identified by the processor used). The template has
members that is set with appropriate values during driver
initialisation. This change is done to support new controllers with
minimal change to existing code. In future, for a new controller
support, a template will be declared and its members initialised
appropriately.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (originally submitted by Christoph Hellwig) removes code
duplication in megasas_build_cmd. It also defines
MEGASAS_IOC_FIRMWARE32 to allow 64 bit compiled applications to work.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When the scsi_execute_async interface was added it ended up reducing
the flexibility of userspace to send arbitrary scsi commands through
sg using SG_IO. The SG_IO interface allows userspace to specify the
CDB length. This is now ignored in scsi_execute_async and it is
guessed using the COMMAND_SIZE macro, which is not always correct,
particularly for vendor specific commands. This patch adds a cmd_len
parameter to the scsi_execute_async interface to allow the caller
to specify the length of the CDB.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Resetting the adapter causes the ServeRAID driver to exceed
the max time allowed by the softlock watchdog. Resetting the
hardware can easily require 30 or more seconds. To avoid the
"BUG: soft lockup detected on CPU#0!"
result, this patch replaces the mdelay() calls in the
initialization/reset routines with msleep().
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Internal lun discovery has been removed since fc_transport
integration. Short-circuiting for tape-devices in
qla2x00_update_fcport() could inadvertently result in a
blocked rport timing-out and its targets being reaped.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A target can LOGO an initiator at any time (i.e. during I/O,
due to a controller hicup, or as a simple authentication
mechanism after an initial CDB command), when this occurs,
the driver attempts to relogin (PLOGI) to the device via the
DPC thread. Add code to make the appropriate upcall to the
FC transport layer (fc_remote_port_add()) upon successful
completion of the PLOGI.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver can typically detect port-loss during an
interrupt context (i.e. via interrogation of a status IOCB's
completion status [CS_PORT_LOGGED_OUT]. Due to the calling
requirements of the fc_rport APIs, the driver would defer
removal of the device to the default workqueue. If the
work-item was preceded by an event which caused the port to
obtain visibility (relogin successful, target re-logged into
the topology), deferred removal could inadvertently drop the
rport. The code also no longer defers removal via the
default workqueue, instead opting for use of the driver's
own DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch below "fixes" calculation of the virt_addr for the AUTO_REQSENSE
case. I put "fixes" in quotes because the real fix would be to completely
remove it, but that's beyond the scope of this patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New versions of the Power5 firmware can send a "re-enable" message to
the virtual scsi adapter. This fix makes us handle the message
correctly. Without it, the driver goes catatonic and the system crashes
unpleasantly.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
some driver clean ups, and a re-posting of changes that are needed
to match the updated TPS.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a subset of the bluesmoke project core code, stripped of the NMI work
which isn't ready to merge and some of the "interesting" proc functionality
that needs reworking or just has no place in kernel. It requires no core
kernel changes except the added scrub functions already posted.
The goal is to merge further functionality only after the core code is
accepted and proven in the base kernel, and only at the point the upstream
extras are really ready to merge.
From: doug thompson <norsk5@xmission.com>
This converts EDAC to sysfs and is the final chunk neccessary before EDAC
has a stable user space API and can be considered for submission into the
base kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EDAC requires a way to scrub memory if an ECC error is found and the chipset
does not do the work automatically. That means rewriting memory locations
atomically with respect to all CPUs _and_ bus masters. That means we can't
use atomic_add(foo, 0) as it gets optimised for non-SMP
This adds a function to include/asm-foo/atomic.h for the platforms currently
supported which implements a scrub of a mapped block.
It also adjusts a few other files include order where atomic.h is included
before types.h as this now causes an error as atomic_scrub uses u32.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
*) mark as "EXPERIMENTAL" various items that either aren't very stable or
that are actively crashing the setup of users which don't really need them
(i.e. HIGHMEM and 3-level pagetables on x86 - nobody needs either,
everybody reports "I'm using it and getting trouble").
*) move net/Kconfig near to the rest of network configurations, and
drivers/block/Kconfig near "Block layer" submenu.
*) it's useless and doesn't work well to force NETDEVICES on and to disable
the prompt like it's done. Better remove the attempt, and change that to a
simple "default y if UML".
*) drop the warning about "report problems about HPPFS" - it's redundant
anyway, as that's the usual procedure, and HPPFS users are especially
technical (i.e. they know reporting bugs is _good_).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix incorrect variable size used to hold register value. This bug might
wipe out a portion of the TCR value when setting the interface options.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Eddie C. Dost <ecd@brainaid.de>
I have the following patch for serial console over the RSC
(remote system controller) on my E250 machine. It basically adds
support for input-device=rsc and output-device=rsc from OBP, and
allows 115200,8,n,1,- serial mode setting.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Andrew Victor
This patch fixes two small issues with 2.6.15-git12.
1) Corrected major/minor numbers for ttyAT devices in the KConfig help.
(Patch from Karl Olsen)
2) tty->flip.count has been removed.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove page refcount manipulations from cassini driver by using
another field in struct page. Needed for lockless pagecache.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
in attempting to not send the "prefetch" patch, we broke the receive code,
this patch fixes that issue.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Moore, Eric