Patch from Ben Dooks
All the S3C24XX based devices currently have similar
uart blocks, in the same location. Make the process
of adding new uart blocks easier by commonising the
device definitions and adding a new init function
for the cpu code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Platform devices for the LEDs on all the SMDK24XX boards
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
This adds the platform device for SSP/SPI controller, and declares
the ads7846 device hooked up to it. Not all Lubbock boards appear
to populate the connector needed to use this instead of the ucb1400
chip, but it can always be used as a temperature sensor.
In short, this is probably most useful as an example of how to
provide the configuration data used by the pxa2xx_spi driver.
(Last tested against a slightly earlier version of that driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch fixes some dyntick locking issues on ARM as pointed
out by Russell King.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Move the printk of the CPU information and IDCODE
before the checking of the table entry validity
to aide in debugging new cpu entries.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
If CONFIG_CPU_DCACHE_WRITETHOUGH is set, then the
S3C24XX PM code fails to compile, as there is no
need to flush the D-cache, the flush function
arm920_flush_kern_cache_all() is not compiled.
Fix the code to not use this if the config is set.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The default serial port-mapping for the Osiris has
the port 2 mapped onto the first serial port, and
no port1. Correct this so port 1 is port.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
This code was still using the old format for the ARMv6 CPU id and it wasn't
flushing the caches on the MPCore CPU (and other ARM1176 cores). The patch
changes the mask bits to cope with the new id format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gather the common sigmask savbing code inside setup_sigcontext(), and
rename the function setup_sigframe(). Pass it a sigframe structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gather the sigmask restoration code inside restore_sigcontext(), and
rename the function restore_sigframe(). Pass it a sigframe structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sigframe is now a contained subset of rt_sigframe, so we can start
to re-use code which accesses sigframe data for both rt and non-rt
signals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ucontext contains both the sigcontext and sigmask structures, and
is also used for rt signal contexts. Re-use this structure for
non-rt signals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's not much point in splitting the sigmask between two different
locations, so copy it entirely into a proper sigset_t. This will
eventually allow rt_sigframe and sigframe to share more code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These two members appear to be surplus to requirements. Discussing
this issue with glibc folk:
| > Additionally, do you see any need for these weird "puc" and "pinfo"
| > pointers in the kernels rt_sigframe structure? Can we kill them?
|
| We can kill them. I checked with Phil B. about them last week, and he
| didn't remember any reason they still needed to be there. And nothing
| should know where they are on the stack. Unfortunately, doing this
| will upset GDB, which knows that the saved registers are 0x88 bytes
| above the stack pointer on entrance to an rt signal trampoline; but,
| since puc and pinfo are quite recognizable, I can adapt GDB to support
| the new layout if you want to remove them.
So remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Paul Brook
The old-abi sys_syscall syscall is broken when called from Thumb mode. It
assumes the syscall number is an Arm syscall number (ie. starts from
__NR_OABI_SYSCALL_BASE). In thumb mode syscall numbers start from zero.
The patch below fixes this by clearing the nigh bits of the syscall number
instead of inverting them. Technically this means we accept some invalid
syscall numbers, but I can't see how that could be a problem. The two sets of
numbers far apart that unimplemented syscalls should still be rejected.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds default configuration file PNX4008 ARM platform.
It\'s basically the same as the previos one.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds basic chip support for PNX4008 ARM platform.
It's basically the same as the previous one, but with the rmk's
comments taken into account.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Driver for operating SSP devices through LPD7A40X CPLD chip. This
driver is used by the audio codecs.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Board support and LCD panel configurations to integrate lh7a40x's with
the amba clcd driver.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Revised default configuration files.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x_platform files. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x platform headers. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both Integrator and Versatile were using set_irq_handler() and
enable_irq(), and working around the initialisation of the
chained interrupt, instead of the more correct
set_irq_chained_handler() function. Fix Integrator and
Versatile to use the right function, and remove these work-arounds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that kconfig can load multiple configurations, it becomes simple to
integrate the split config step, by simply comparing the new .config file with
the old auto.conf (and then saving the new auto.conf). A nice side effect is
that this saves a bit of disk space and cache, as no data needs to be read
from or saved into the splitted config files anymore (e.g. include/config is
now 648KB instead of 5.2MB).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
From: Lennert Buytenhek <buytenh@wantstofly.org>
The recent renaming of m48t86's ->readb() and ->writeb() platform driver
methods (2d7b20c188) to ->readbyte() and
->writebyte() to fix the ia64 build broke the build of the cirrus ep93xx
ARM platform. This patch fixes it up.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Matt Reimer
There is a subtle bug in the GPIO interrupt status register
handling in arch/arm/mach-imx/irq.c:imx_gpio_ack_irq(). The
documentation states that a 1 should be written to the relevant bit to
acknowledge a GPIO interrupt, but that is not what the code does.
The problem is that the |= writes back 1s for all the *other*
interrupts represented in the register, so interrupts could get lost.
For example, if interrupts are pending for GPIO B10 and B12, ISR_B
would have the value 0x00001400. Then when the interrupt code handles
GPIO B10, it eventually calls imx_gpio_ack_irq(IRQ_GPIOB(10)), which
effectively does this:
ISR_B |= 1 << 10;
with the result that (0x00001400 | 0x00000400) is written, clearing
the interrupt status bits for *both* GPIO B10 and B12.
The fix is to write 1s only for the interrupts we want to clear.
The same problem seems to be occurring in the DMA code; this patch
does not address those issues.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a power budget variable to the PXA OHCI platform data and add a
default value for the spitz platform(s) which prevents known failures
with certain USB devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While testing the genirq code on ARM, a condition was found whereby
the Neponset IRQ handler was being re-entered, causing the system
to deadlock.
Under the ARM IRQ code, this would not have been a visible problem
because the "simple" IRQ handling had no re-entrancy protection.
Resolve this by acknowledging the parent interrupt after we mask it
when we are going to handle one of our "special" level-based sources
(from ethernet or USAR chip.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Steve Yang
MACHINE_START struct doesn't have any bootargs location for the
mainstone. Result is no kernel command args get passed; no serial driver
is selected for console and results in a silent boot failure.
Signed-off-by: Steve Yang <steve.yang@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On the ixp23xx, the microengine thread interrupt sources are numbered
56..119, but their mask/status bits are located in bit positions 64..127
in the various registers in the interrupt controller (bit positions
56..63 are unused.)
We don't deal with this, so currently, when asked to enable IRQ 64, we
will enable IRQ 56 instead.
The only interrupts >= 64 are the thread interrupt sources, and there
are no in-tree users of those yet, so this is fortunately not a big
problem, but this needs fixing anyway.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM Architecture Reference Manual lists bit 4 of the PMD as "implementation
defined" and it must be set to zero on Intel XScale CPUs or the cache does
not behave properly. Found by Mike Rapoport while debugging a flash issue
on the PXA255:
http://marc.10east.com/?l=linux-arm-kernel&m=114845287600782&w=1
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We don't enable the BTB on the ixp2350 as that can cause weird
crashes (erratum #42.) However, some bootloaders enable the BTB,
which means that we have to disable the BTB explicitly.
Found thanks to Tom Rini.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Thomas Gleixner
The mainstone board pcmcia interrupt have been enabled via setup_irq()
and the following socket check calls enable_irq again. Set the NOAUTOEN flag so the interrupt is not automatically enabled in setup_irq()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dimitry Andric
In arch/arm/mach-s3c2410/sleep.S, the coprocessor registers are saved at
suspend time, and restored at resume time. However, an undefined
instruction is used when attempting to restore a non-existent "auxiliary
control register". This leads to a crash on S3C2412, which has an ARM926
core instead of an ARM920.
At suspend time, the following fragment runs:
mrc p15, 0, r7, c2, c0, 0 @ translation table base address
mrc p15, 0, r8, c2, c0, 0 @ auxiliary control register
mrc p15, 0, r9, c1, c0, 0 @ control register
and at resume time, the following fragment runs:
mcr p15, 0, r7, c2, c0, 0 @ translation table base
mcr p15, 0, r8, c1, c1, 0 @ auxilliary control
...
mcr p15, 0, r9, c1, c0, 0 @ turn on MMU, etc
There are several problems with these fragments:
1. The ARM920 and ARM926 cores don't have any "auxiliary control
register", at least not according to the ARM920 and ARM926 TRM's.
2. The 2nd line of suspend erroneously saves the c2 register again.
3. This saved c2 value is restored using an undefined instruction. For
some reason this does not crash on ARM920, but does crash on ARM926.
The following patch fixes all these problems.
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Yes, this looks sensible
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch converts struct dma_resources to named initializers.
Besides fixing a compile error in -mm, it didn't sound like a bad idea.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Harry Fearnhamm
This patch fixes the occasional lockup seen in early boot stage
on RealView MPCore system.
Signed-off-by: Harry Fearnhamm <Harry.Fearnhamm@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
This patch modifies the __ioremap_pfn and __iounmap functions in
arch/arm/mm/ioremap.c to use vunmap instead of vfree.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Assembly code that calls C code must ensure the C code sees a 64-bit
aligned stack pointer.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Uwe Zeisberger
The symbol is only used in arch/arm/kernel/head-common.S. This in turn
is included from arch/arm/kernel/head.S and arch/arm/kernel/head-nommu.S
which include asm-offsets.h .
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Machek
Update collie defconfig to something that can bring closer-to-working
system to its user.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM thread struct allocator is racy on SMP systems. Fix it by
turning it into a per-cpu based allocator. This also allows keeps
the cache cache warm for thread structs and kernel stacks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update versatile default configuration, enabling the AACI sound driver,
VFP and Versatile AB support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
aaed2000 map_desc.pfn conversion
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Since this patch:
[ARM] 3366/1: Allow the 16bpp mode configuration in the CLCD control register
linux/amba/bus.h needs to be included before linux/amba/clcd.h
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Patch:
[ARM] 2982/1: Replace map_desc.physical with map_desc.pfn: aaec2000
incorrectly expanded the struct map_desc for aaec2000.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch fixes the addruart macro to work with both mmu enabled and
disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SA1100 RTC alarm can be configured to wake up the CPU
from sleep mode, and the RTC driver has been using the
API to configure this mode. Unfortunately, the code was
which sets the required bit in the hardware was missing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Intel PXA27x developers manual section 5.4.1.1 lists a priority
distribution for the DMA channels differently than what the code
currently assumes. This patch fixes that.
Noticed by Simon Vogl <vogl@soft.uni-linz.ac.at>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
The ARM VFP FPSCR register is corrupted when a condition flags modifying
VFP instruction is followed by a non-condition flags modifying VFP
instruction and both instructions raise exceptions. The fix is to
read the current FPSCR in between emulation of these two instructions
and use the current FPSCR value when handling the second exception.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Uwe Zeisberger
added the following constants:
- MACHINFO_TYPE
- MACHINFO_NAME
- MACHINFO_PHYSIO
- MACHINFO_PGOFFIO
- PROCINFO_INITFUNC
- PROCINFO_MMUFLAGS
and removed their definition from head.S and head-nommu.S
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch moves the i.MX uart resources and the gpio pin setup to the
board files. This allows the boards to decide how many internal uarts
are connected to the outside world and whether they use rts/cts or
not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Uwe Zeisberger
a) use coprocessor 14
b) make reading the dcc status volatile
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch allows for the addition of IXP4xx systems that do not make
use of the PCI interface by moving the CONFIG_PCI symbol selection to
be platform-specific instead of for all of IXP4xx. If at least one machine
with PCI support is built, the PCI code will be compiled in, but when
building !PCI, this will drastically shrink the kernel size.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The VFP code can leak VFP_NAN_FLAG into the FPSCR. It doesn't correspond
to any real FPSCR bit (and overlaps one of the exception flags).
Bug report from Daniel Jacobowitz
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The AAPCS says that enums can be variably sized depending on the range
of valid values. This is not the accepted behaviour under linux so for
compatibility gcc has an aapcs-linux target, the main difference being
that enums are always of type int. Change the ARM Makefile to use this
target.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fix compilation problem of start-up codes.
(head-nommu.S, arch/arm/kernel/Makefile)
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is back again. Offending patch is x86_64-mm-hotadd-reserve.patch
arch/arm/kernel/setup.c:435: error: conflicting types for 'add_memory'
include/linux/memory_hotplug.h:102: error: previous declaration of 'add_memory' was here
arch/arm/kernel/setup.c:435: error: conflicting types for 'add_memory'
include/linux/memory_hotplug.h:102: error: previous declaration of 'add_memory' was here
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The irq2gpio array was recently converted from an array of ints to an
array of chars (by patch 3368/1.) However, this array contains elements
that are -1, and on ARM, the char type is unsigned by default, so this
patch broke the GPIO check in ixp4xx_set_irq_type.
Change the 'char' to be a 'signed char' to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
corgi_ssp_probe() should not access GPDR directly but should use
pxa_gpio_mode() which has appropriate locking and other safeguards.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Move platform_scoop_config from the SharpSL scoop PCMCIA driver to
the SCOOP driver. This avoids build failures when PCMCIA is not built
or is modular (scoop.c itself cannot be modular).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The at91_cf driver got out of sync with certain changes in the PCMCIA
layer, notably getting rid of some duplication of data ... causing the
version merged to kernel.org to fail compiling.
This patch gives the at91_cf platform device a new iomem resource, using
it so this new pcmcia scheme works. It also cleans up some whitepsace
bugs that have accumulated over time (mostly too-long lines).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
Fix bad spelling of partition
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The wrong variable is written back to CLKDIVN
register if the USB PLL speed is above 94MHz
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While cleaning up parisc_ksyms.c earlier, I noticed that strpbrk wasn't
being exported from lib/string.c. Investigating further, I noticed a
changeset that removed its export and added it to _ksyms.c on a few more
architectures. The justification was that "other arches do it."
I think this is wrong, since no architecture currently defines
__HAVE_ARCH_STRPBRK, there's no reason for any of them to be exporting it
themselves. Therefore, consolidate the export to lib/string.c.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for
each arch. Its definition is sometimes configurable. Indeed, ia64 defines 5
NODES_SHIFT values in the current git tree. But it looks a bit messy.
SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has
been changeable by config. Suitable node's number may be changed in the
future even if it is other architecture. So, I wrote configurable node's
number.
This patch set defines just default value for each arch which needs multi
nodes except ia64. But, it is easy to change to configurable if necessary.
On ia64 the number of nodes can be already configured in generic ia64 and SN2
config. But, NODES_SHIFT is defined for DIG64 and HP'S machine too. So, I
changed it so that all platforms can be configured via CONFIG_NODES_SHIFT. It
would be simpler.
See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Catalin Marinas
This patch changes the double registers numbering to 0-15 from even 0-30,
in preparation for future VFP extensions. It also fixes the VFP_REG_ZERO
bug (value 16 actually represents the 8th double register with the original
numbering).
The original mcrr/mrrc on CP10 were generating FMRRS/FMSRR instead of
FMRRD/FMDRR. The patch changes to CP11 for the correct instructions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The NaN case was dealed with by the "exponent >= ... + 32" condition but it
was not setting the value "d" to 0.
Signed-off-by: Ken'ichi Kuromusha <musha@aplix.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Glibc interprets the HWCAP bits and decides on what features to use.
However, even if the features are present in the hardware, they are not
always supported by the kernel and hence the corresponding bits have to be
cleared from the elf_hwcap variable.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The clkout0/1 output parent code is missing the
HCLK option, and does not set clk->parent field
after updating the clock field
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
common-smdk.c does not include its own header file
defining the exported prototypes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Recent change to use both id and name when available was
not necessarily returning the right clock as it also searched
for clock name afterwards. This caused MMC to break on H2 and
H3 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Remove unnecessary omap_nop_release() as noted by RMK.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We had two implementations for flushing the cache, which meant StrongARM
caches weren't being correctly flushed. Fix this by always using the
v4wb_flush_kern_cache_all method, rather than duplicating it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
FLUSH_BASE must be visible to arch/arm/mm/init.c in order for the
memory region to be setup. Move these definitions from
asm-arm/arch-*/hardware.h into asm-arm/arch-*/memory.h where mm
stuff can see them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
This patch adds support of i.MX/MX1 SD/MMC controller.
It has been significantly redesigned from the original Sascha Hauer's
version to support scatter-gather DMA, to conform to latest Pierre Ossman's
and Russell King's MMC-SD Linux 2.6.x infrastructure.
The handling of all events has been moved to the softirq context
and is designed with no busy-looping in mind. Unfortunately
some controller bugs has to be overcome by limited looping
about 2-20 usec but these are observed only for initial card
recognition phase.
There are still some missing/missed IRQs problems under heavy load.
Help of somebody with access to the full SDHC design information
is probably necessary.
Regenerated against 2.6.16-git-060402 to solve clash with other patches.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs OMAP board support with linux-omap tree.
The highlights of the patch are:
- Add support for Nokia 770 by Juha Yrjola
- Add support for Samsung Apollon by Kyungmin Park
- Add support for Amstrad E3 videophone by Jonathan McDowell
- Remove board-netstar.c board support as requested by Ladislav Michl
- Do platform_device registration in board files by Komal Shah et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update misc OMAP core code from linux-omap tree:
- McBSP updates by Samuel Ortiz, Andrzej Zaborowski
- Whitespace cleanups by Ladislav Michl
- Other fixes by various linux-omap developers
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP framebuffer low-level init code from linux-omap tree
by Imre Deak.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP PM code from linux-omap tree:
- Move PM code from plat-omap to mach-omap1 and mach-omap2
by Tony Lindgren
- Add minimal PM support for omap24xx by Tony Lindgren and
Richard Woodruff
- Misc updates to omap1 PM code by Tuukka Tikkanen et al
- Updates to the SRAM code needed for PM and FB by Imre Deak
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP GPIO code from linux-omap tree:
- Fix omap16xx edge control by Juha Yrjola
- Support for additional omap16xx trigger modes by Dirk Behme
- Fix edge detection by Tony Lindgren et al.
- Better support for omap15xx and omap310 by Andrej Zaborowski
- Fix omap15xx interrupt bug by Petukhov Nikolay
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP pin multiplexing code from linux-omap tree.
This patch adds new pin configurations by various OMAP
developers, and suport for omap730 by Brian Swetland.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP timers from linux-omap tree. The highlights of the
patch are:
- Move timer32k code from mach-omap1 to plat-omap and make it
work also on omap24xx by Tony Lindgren
- Add support for dmtimer idle check for PM by Tuukka Tikkanen
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP clock framework from linux-omap tree.
The highlights of the patch are:
- Add support for omap730 clocks by Andrzej Zaborowski
- Fix compile warnings by Dirk Behme
- Add support for using dev id by Tony Lindgren and Komal Shah
- Move memory timings and PRCM into separate files by Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch updates the platform device resources for the Ethernet and
MMC peripherals. It also adds platform device information for the NAND
(SmartMedia), I2C and the RTC.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
On the Atmel AT91RM9200-DK and -EK boards, a pin is used to control
whether the card socket is used for a DataFlash Card or an MMC/SD card.
We now default to MMC/SD in the configuration files.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds support for the LED(s) on the AT91RM9200-based boards.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Force the Sharp Zaurus Poodle memory size to 32MB.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
From: Stefano Fedrigo <aleph@develer.com>
This adds to the MX1ADS platform the needed code to detect
insertion/removal of an MMC/SD card. Tested on a v1.1 board.
Signed-off-by: Stefano Fedrigo <aleph@develer.com>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
This patch contains simplified set of changes to add scatter-gather
emulation capability into MX1 DMA support. The result should
be still usable for next combination of DMA transfers
Statter-Gather/linear/2D/FIFO to linear/2D/FIFO and
linear/2D/FIFO to Statter-Gather/2D/FIFO
The patch corrects channel priority allocation to be compatible
with MX1 hardware implementation.
Previous code has not been adapted from its PXA original.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Instantiate the recently merged m48t86 rtc driver in the ts72xx code.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Instantiate the recently merged ep93xx rtc driver in the ep93xx code.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
NAND definitions for the HP iPAQ RX3715's
internal NAND flash
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The NAND timings on the Anubis are too large
to be selected when running at 133MHz memory
clock.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the bug in the UPLL enable code which should
have put a 200uS delay in if enabling the USB PLL
from the state where it is off.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add SMDK2410/SMDK2440 NAND device information
and default partition table.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Set default state of LEDs to off
Fixes context of Patch #3442/1
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the I/O coherent cache available on the
xsc3. The approach is to provide a simple API to determine whether the
chipset supports coherency by calling arch_is_coherent() and then
setting the appropriate system memory PTE and PMD bits. In addition,
we call this API on dma_alloc_coherent() and dma_map_single() calls.
A generic version exists that will compile out all the coherency-related
code that is not needed on the majority of ARM systems.
Note that we do not check for coherency in the dma_alloc_writecombine()
function as that still requires a special PTE setting. We also don't
touch dma_mmap_coherent() as that is a special ARM-only API that is by
definition only used on non-coherent system.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The SMDK2410 and SMDK2440 boards have a number of items
in common, including the LEDs, Ethernet, PCMCIA. Make
a common SMDK support file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On the Double Espresso board, the IXP2350s are PCI slave devices and
we skip calling pci_common_init() as that enumerates the bus. But even
though we are a PCI slave device, there is still some PCI-related setup
that has to be done.
Create ixp23xx_pci_common_init(), move the common initialisation bits
there, and have this function called from both the PCI master and the
PCI slave init path.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Machek
> The kautobuild found the following error while trying to build 2.6.16-git18
> using collie_defconfig:
>
> arch/arm/mach-sa1100/collie.c:92: error: 'collie_uart_set_mctrl' undeclared here (not in a function)
> arch/arm/mach-sa1100/collie.c:93: error: 'collie_uart_get_mctrl' undeclared here (not in a function)
> make[1]: *** [arch/arm/mach-sa1100/collie.o] Error 1
> make: *** [arch/arm/mach-sa1100] Error 2
> make: Leaving directory `/var/tmp/kernel-orig'
This fixes above compile error by adding missing pieces of uart
support, and fixes compilation.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Komal Shah
This patch fixes the duplicate exports of string library functions.
Signed-off-by: Komal Shah <komal_shah802003@yahoo.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3424/2: ixp23xx: fix uncompress.h for recent CRLF decompressor change
[ARM] 3434/1: pxa i2s amsl define
[ARM] 3425/1: xsc3: need to include pgtable-hwdef.h
[ARM] Allow un-muxed syscalls to be available for everyone
[ARM] 3420/1: Missing clobber in example code
[ARM] nommu: fixups for the exception vectors
[ARM] nommu: add nommu specific Kconfig and MMUEXT variable in Makefile
[ARM] nommu: start-up code
[ARM] nommu: MPU support in boot/compressed/head.S
The only user of get_wchan is the proc fs - and proc can't be built modular.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Generalise the Corgi backlight driver by moving the default intensity and
limit mask settings into the platform specific data structure. This enables
the driver to support other Zaurus hardware, specifically the SL-6000x (Tosa)
model.
Also change the spinlock to a mutex (the spinlock is overkill).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds LED drivers for LEDs found on the Sharp Zaurus c6000 model (tosa).
Signed-off-by: Dirk Opfer <dirk@opfer-online.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds LED drivers for LEDs found on the Sharp Zaurus c7x0 (corgi, shepherd,
husky) and cxx00 (akita, spitz, borzoi) models.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an LED trigger for the charger status as found on the Sharp Zaurus series
of devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the foundations of a new LEDs subsystem. This patch adds a class which
presents LED devices within sysfs and allows their brightness to be
controlled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lennert Buytenhek
Adapt xsc3 to the changes in 74945c8616
(xsc3 was written before but merged after the latter went in.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Provide Cirrus EP93xx AMBA PL010 serial support.
[SERIAL] amba-pl010: allow platforms to specify modem control method
[SERIAL] Remove obsoleted au1x00_uart driver
[SERIAL] Small time UART configuration fix for AU1100 processor
Patch from Paul Brook
The example code in the source documentation for __kernel_dmb
clobbers r0 but doesn't list it the asm clobber list.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Intel ixp23xx series of CPUs. The
ixp23xx is an XSC3 based CPU with 512K of L2 cache, a 64bit 66MHz PCI
interface, two DDR RAM interfaces, QDR RAM interfaces, two gigabit
MACs, two 10/100 MACs, expansion bus, four microengines, a Media and
Switch Fabric unit almost identical to the one on the ixp2400, two
xscale (8250ish) UARTs and a bunch of other stuff.
This patch adds the core ixp23xx support code, and support for the
ADI Engineering Roadrunner, Intel IXDP2351, and IP Fabrics Double
Espresso platforms.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add support for the LogicPD PXA270 Card Engine.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add ixp23xx defconfig.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the new XScale v3 core. This is an
ARMv5 ISA core with the following additions:
- L2 cache
- I/O coherency support (on select chipsets)
- Low-Locality Reference cache attributes (replaces mini-cache)
- Supersections (v6 compatible)
- 36-bit addressing (v6 compatible)
- Single instruction cache line clean/invalidate
- LRU cache replacement (vs round-robin)
I attempted to merge the XSC3 support into proc-xscale.S, but XSC3
cores have separate errata and have to handle things like L2, so it
is simpler to keep it separate.
L2 cache support is currently a build option because the L2 enable
bit must be set before we enable the MMU and there is no easy way to
capture command line parameters at this point.
There are still optimizations that can be done such as using LLR for
copypage (in theory using the exisiting mini-cache code) but those
can be addressed down the road.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As per the corresponding change to the serial drivers, arrange
for ARM decompressors to give CRLF. Move the common putstr code
into misc.c such that machines only need to supply "putc" and
"flush" functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add an RTC subsystem driver for the ARM SA1100/PXA2XX processor RTC.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some namespace conflicts between the RTC subsystem and the ARM Integrator
time functions.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes from the ARM subsytem some of the rtc-related functions
that have been included in the RTC subsystem. It also fixes some naming
collisions.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ifeq ($CONFIG_PREEMPT,y) -> ifeq ($(CONFIG_PREEMPT),y)
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Erik Mouw
The LART website moved to http://www.lartmaker.nl/. This patch
updates the URL in ARM specific files.
Signed-off-by: Erik Mouw <erik@bitwizard.nl>
Acked-by: Jan-Derk Bakker <jdb@lartmaker.nl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The high page vector (0xFFFF0000) does not supported in nommu mode.
This patch allows the vectors to be 0x00000000 or the begining of DRAM
in nommu mode.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds Kconfig-nommu for noMMU specific configurations
and MMUEXT variable into Makefile.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds nommu version start-up code head-nommu.S.
The common part of the start-up codes is moved to head-common.S.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds MPU support in boot/compressed/head.S.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The amba-pl010 hardware does not provide RTS and DTR control lines; it
is expected that these will be implemented using GPIO. Allow platforms
to supply a function to implement manipulation of modem control lines.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add an EXPORT_SYMBOL for the Akita IO Expander Device.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3030/2: fix permission check in the obscur cmpxchg syscall
[ARM] nommu: rename compressed/head.S symbols to a new style
[ARM] select TLS_REG_EMUL and NEEDS_SYSCALL_FOR_CMPXCHG
[ARM] nommu: Move hardware page table definitions to pgtable-hwdef.h
[ARM] Move read of processor ID out of lookup_processor_type()
[ARM] Fix typo in tlbflush.h
[ARM] noMMU: removes TLB codes in nommu mode
[ARM] noMMU: block sys_fork in nommu mode
[ARM] 3399/1: Fix link problem when CONFIG_PRINTK is disabled
[ARM] 3398/1: Fix the VFP registers loading/storing base address
[ARM] 3397/1: AT91RM9200 Header update
[ARM] 3385/1: Battery support for sharp zaurus sl-5500 (collie)
[ARM] SMP: don't set cpu_*_map in smp_prepare_boot_cpu
include/linux/clk.h is betraying its ARM origins
[ARM] Move enable_irq and disable_irq to assembler.h
[ARM] 3391/1: use PLAT8250_DEV_PLATFORM{,1} for platform device id instead of 0/1
Patch from Lennert Buytenhek
Add a PLAT8250_DEV_PLATFORM2, and convert the two ixdp2x01 CPLD serial
ports to use platform serial devices with ids PLAT8250_DEV_PLATFORM[12].
(The on-chip xscale UART is PLAT8250_DEV_PLATFORM, id #0.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Quoting RMK:
|pte_write() just says that the page _may_ be writable. It doesn't say
|that the MMU is programmed to allow writes. If pte_dirty() doesn't
|return true, that means that the page is _not_ writable from userspace.
|If you write to it from kernel mode (without using put_user) you'll
|bypass the MMU read-only protection and may end up writing to a page
|owned by two separate processes.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Malcolm Parsons
Printking a backtrace requires printk, so disable backtrace code
when printk is disabled.
Without this patch, a kernel with CONFIG_PRINTK disabled does not link:
arch/arm/lib/lib.a(backtrace.o): In function `c_backtrace':
arch/arm/lib/backtrace.S:(.text+0x108): undefined reference to `printk'
arch/arm/lib/backtrace.S:(.text+0x11c): undefined reference to `printk'
arch/arm/lib/lib.a(backtrace.o):(.fixup+0x8): undefined reference to `printk'
Signed-off-by: Malcolm Parsons <malcolm.parsons@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The current VFP code corrupts the VFP registers (including the control
ones) if more than one floating point application is executed at the same
time. This patch fixes the updating of the load/store base addresses for
the VFP registers.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Machek
This adds support for battery reading on collie. Collie slowly charges
battery even with charging disabled, so I did not yet enable fast
charge.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The recent addition of boot_cpu_init() implements the initialisation
of the online, present and possible cpu maps for the boot CPU, so
there is no reason to duplicate this in the architecture
smp_prepare_boot_cpu() hook.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/sam/kbuild: (46 commits)
kbuild: remove obsoleted scripts/reference_* files
kbuild: fix make help & make *pkg
kconfig: fix time ordering of writes to .kconfig.d and include/linux/autoconf.h
Kconfig: remove the CONFIG_CC_ALIGN_* options
kbuild: add -fverbose-asm to i386 Makefile
kbuild: clean-up genksyms
kbuild: Lindent genksyms.c
kbuild: fix genksyms build error
kbuild: in makefile.txt note that Makefile is preferred name for kbuild files
kbuild: replace PHONY with FORCE
kbuild: Fix bug in crc symbol generating of kernel and modules
kbuild: change kbuild to not rely on incorrect GNU make behavior
kbuild: when warning symbols exported twice now tell user this is the problem
kbuild: fix make dir/file.xx when asm symlink is missing
kbuild: in the section mismatch check try harder to find symbols
kbuild: fix section mismatch check for unwind on IA64
kbuild: kill false positives from section mismatch warnings for powerpc
kbuild: kill trailing whitespace in modpost & friends
kbuild: small update of allnoconfig description
kbuild: make namespace.pl CROSS_COMPILE happy
...
Trivial conflict in arch/ppc/boot/Makefile manually fixed up
This adds missing bits of collie (sharp sl-5500) PCMCIA support and
MFD support.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch renames symbols to a new style to prepare mpu support
code merging. e.g. __armv4_cache_on --> __armv4_mmu_cache_on
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
5d25ac038a broke VFP builds due to
enable_irq not being defined as an assembly macro. Move it to
assembler.h so everyone can use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch changes iop3xx and omap2 and to use PLAT8250_DEV_PLATFORM{,1}
as platform device id instead of just hardcoding 0/1 directly.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Erik Hovland
I found a typo and what seems to be a run-on sentence in
arch/arm/common/dmabounce.c
This patch corrects both.
Signed-off-by: Erik Hovland <erik@hovland.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch includes a few changes to the clock support on the
AT91RM9200.
1. Added definitions for Ethernet, MMC, TWI, USARTs, and SPI peripheral
clocks.
2. Replaced some hard-coded hex values with the text definitions in
at91rm9200_sys.h.
3. If the USB96M bit is set for PLLB, then the rate of PLLB is not
affected but only the USB Host/Device clocks which are derived from it.
Issue reported by Sergei Sharonov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
If the timer interrupt is ever significantly delayed (or after the
system was suspended), the system could spin incrementing the time for
too long.
The fix is to replace the "do {} while" with a "while {}".
Orignal patch by Savin Zlobec and Peter Menzebach.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Unify the five existing ixp2000 defconfigs into one defconfig.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
ixp2000 used to initially mark GPIO interrupts as invalid, and not
mark them valid until set_irq_type() was called, but this doesn't
work if you want to use request_irq() with the SA_TRIGGER_* flags.
So, just mark the GPIO interrupts valid from the beginning. We
configure GPIOs as inputs when set_irq_type() is called anyway, so
this shouldn't be a problem.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Have an explicit mm call to split higher order pages into individual pages.
Should help to avoid bugs and be more explicit about the code's intention.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only issue a "nobody cared" warning after 99900 spurious interrupts.
This avoids the occasional spurious interrupt causing warnings, as
per x86.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need this to be zero initialised. Since this is an array, use kcalloc
rather than kzalloc or kmalloc.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add Simtec Osiris to the default build, and enable the
USB-OHCI section by default.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the build of arch/arm/mach-s3c2410/mach-osiris.c
and fix the warnings from sparse.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add GPIO interrupt support for the first 16 GPIO lines (port A
and B.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add USB bus clock definition for 48MHz fed to OHCI and gadget cores
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add set_rate methods for the extra clocks on the S3C2440
and add the camera UPLL clock source
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add support for clk_set_rate and clk_round_rate to the
s3c2410 clock implementation
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Move the uengine loader from arch/arm/mach-ixp2000 to arch/arm/common
so that ixp23xx can use it too.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add ep93xx defconfig.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add support for setting the direction of and getting/setting the
value of the 64 GPIO lines.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Cirrus ep93xx series of CPUs. The
ep93xx is an ARM920T based CPU with two VICs, PL010 based UARTs,
IrDA, MaverickCrunch floating point coprocessor, between 24 and 64
GPIOs, ethernet, OHCI USB and, depending on the model, pcmcia, raster
engine, graphics accelerator, IDE controller and a bunch of other
stuff.
This patch adds the core ep93xx support code, and support for the
Glomation GESBC-9312-sx and the Technologic Systems TS-72xx SBCs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
ixp4xx_config_irq did not configure the gpio line
as an input.
As an added bonus, the irq2gpio array has been converted
from int to char.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Peter Teichmann
Currently, if the kernels HZ value is greater than 100, delays with the udelay function are too short. This can cause trouble for instance with the zd1201 usb wlan driver.
This patch suggests a solution that keeps the overhead small and maintains (hopefully) sufficient resolution.
Signed-off-by: Peter Teichmann
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch adds support for Intel's IXDP28x5 platform. This
is just and IXDP2801 with a new CPU rev but the bootloader
has been updated to reflect a new machine ID so we just build
support for it by default when we build IXDP2801.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add enable and set_parent calls for the dclk
and clkout clocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add clk_set_parent() call to clock code
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Move the UPLL clock registration to the central
clock file, and add an enable method
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add selection for timer code for the Simtec Osiris
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Support for Simtec IM2440D20 CPU modules (Osiris)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This field is redundent since it must be equal to PHYS_OFFSET anyway.
There is no reference to it anymore so remove it at last.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some SoCs have multiple VIC devices. Adapt the generic vic code
to allow multiple implementations to be handled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In all current use cases, "chipdata" is used to store an iomem address.
Mark it with __iomem, and rename it to 'base'. Leave the accessor macros
alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the individual coprocessor handlers to decide when to enable
interrupts, rather than unconditionally enabling them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/hardware.h is not required for the majority of processor support
files, ioremap support, mm initialisation, acorn IO support, nor
the debug code (which picks up its machine specific includes via
debug-macros.S)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, OMAP platforms without the 32K timer left HZ set to
an empty value. Fix this by making the dependency on OMAP_32K_TIMER
rather than OMAP_32K_TIMER_HZ.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/arch/irq.h used to be included from asm/irq.h, but was removed
from the ARM kernel a long time ago. Consequently, the contents
of asm/arch/irq.h (which mostly contain a definition for fixup_irq())
have not been used. Hence, remove asm/arch/irq.h.
Some machine support files incorrectly included this file, making
little or no use of the contents. Move the contents to a local
include file, and remove those include statements as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the HZ definition into Kconfig, and set appropriate defaults
for platforms. Remove mostly empty asm/arch/param.h include file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the hardware PMD and PTE page table definitions from pgtable.h
into pgtable-hwdef.h, and include pgtable-hwdef.h as necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Read the processor ID at boot, and save it in "processor_id" as we
did before. Later, when we re-parse the CPU type in the setup.c code,
re-use the value stored in "processor_id".
This allows a cleaner work-around for noMMU devices without CP#15.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sys_fork is not supported in nommu mode. The other syscalls
that is not supported in nommu mode are to be defined as cond_signal
in kernel/sys_ni.c.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (23 commits)
[PATCH] sysfs: fix a kobject leak in sysfs_add_link on the error path
[PATCH] sysfs: don't export dir symbols
[PATCH] get_cpu_sysdev() signedness fix
[PATCH] kobject_add_dir
[PATCH] debugfs: Add debugfs_create_blob() helper for exporting binary data
[PATCH] sysfs: fix problem with duplicate sysfs directories and files
[PATCH] Kobject: kobject.h: fix a typo
[PATCH] Kobject: provide better warning messages when people do stupid things
[PATCH] Driver core: add macros notice(), dev_notice()
[PATCH] firmware: fix BUG: in fw_realloc_buffer
[PATCH] sysfs: kzalloc conversion
[PATCH] fix module sysfs files reference counting
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE() to USB subsystem
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE() to RCU subsystem
[PATCH] add EXPORT_SYMBOL_GPL_FUTURE()
[PATCH] Clean up module.c symbol searching logic
[PATCH] kobj_map semaphore to mutex conversion
[PATCH] kref: avoid an atomic operation in kref_put()
[PATCH] handle errors returned by platform_get_irq*()
[PATCH] driver core: platform_get_irq*(): return -ENXIO on error
...
platform_get_irq*() now returns on -ENXIO when the resource cannot be
found. Ensure all users of platform_get_irq*() handle this error
appropriately.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Catalin Marinas
Chosing of the CLCD RGB mode is no longer possible via the SYS_CLCD
register on the RealView boards. Instead, this configuration is done in the
CLCD primecell control register directly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
arch/arm/kernel/setup.c declares mem_fclk_21285 when
this is already declared in include/asm-arm/system.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
arch/arm/kernel/compat.c exports two functions,
convert_to_tag_list and squash_mem_tags which
are not defined in any header files, and not
used outside arch/arm/kernel.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the following warnings from sparse:
arch/arm/kernel/process.c:86:6: warning: symbol 'default_idle' was not declared. Should it be static?
arch/arm/kernel/process.c:378:5: warning: symbol 'dump_fpu' was not declared. Should it be static?
Include <linux/elfcore.h> for dump_fpu() decleration, and
make default_idle() static as it is not used outside the file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Albrecht Dreß
Add DMA resources to s3c2410 spi platform devices - dma_(alloc|free)_coherent should now work as expected.
Signed-off-by: Albrecht Dreß <albrecht.dress@lios-tech.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Machek
Enable frontlight during collie bootup, so that display is actually
readable in anything other than bright sunlight.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the reliance of iwmmxt on hand coded alignments.
Since thread_info is always 8K aligned, specifying that fpstate is
8-byte aligned achieves the same effect without needing to resort
to hand coded alignments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patches add the 1-wire drivers
to the ARM Kconfig.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
ARM1136 erratum 371025 (category 2) specifies that, under rare
conditions, an invalidate I-cache by MVA (line or range) operation can
fail to invalidate a cache line. The recommended workaround is to
either invalidate the entire I-cache or invalidate the range by
set/way rather than MVA.
Note that for a 16K cache size, invalidating a 4K page by set/way is
equivalent to invalidating the entire I-cache.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
The patch that would have made the NSLU2
kernel non compatible with other ixp4xx machs
never entered the kernel. So it is actually
safe to remove the prompt dependencies.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
Disable GPIO clocks to allow
the power led to work properly.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When shifting the low-parts of signed numbers, a logical shift
should be used to avoid sign-extending a bit which isn't a sign
bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
nas100d_power_exit(void) gets some protection
to avoid freeing an irq when it is not appropriate to do so.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Chapter B2.7.3 in the latest ARM ARM (with v6 information) states that
the completion of a TLB maintenance operation is only guaranteed by
the execution of a DSB (Data Syncronization Barrier, formerly Data
Write Barrier or Drain Write Buffer).
Note that a DSB is only needed in the flush_tlb_kernel_* functions
since the completion is guaranteed by a mode change (i.e. switching
back to user mode) for the flush_tlb_user_* functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Also from Thomas Gleixner <tglx@linutronix.de>
Function next_timer_interrupt() got broken with a recent patch
6ba1b91213 as sys_nanosleep() was moved to
hrtimer. This broke things as next_timer_interrupt() did not check hrtimer
tree for next event.
Function next_timer_interrupt() is needed with dyntick (CONFIG_NO_IDLE_HZ,
VST) implementations, as the system can be in idle when next hrtimer event
was supposed to happen. At least ARM and S390 currently use
next_timer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kbuild system takes advantage of an incorrect behavior in GNU make.
Once this behavior is fixed, all files in the kernel rebuild every time,
even if nothing has changed. This patch ensures kbuild works with both
the incorrect and correct behaviors of GNU make.
For more details on the incorrect behavior, see:
http://lists.gnu.org/archive/html/bug-make/2006-03/msg00003.html
Changes in this patch:
- Keep all targets that are to be marked .PHONY in a variable, PHONY.
- Add .PHONY: $(PHONY) to mark them properly.
- Remove any $(PHONY) files from the $? list when determining whether
targets are up-to-date or not.
Signed-off-by: Paul Smith <psmith@gnu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Patch from Andrew Victor
disable_irq() lazily disables the interrupt, so the IRQ is only disabled
once the interrupt occurs again. The GPIO interrupt handler therefore
must first check disable_depth to see if the IRQ needs to be disabled.
Orignal patch by Bill Gatliff.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Mårten Wikström
This patch fixes a bug in ixp4xx_set_irq_type() which leads to
GPIO being incorrectly set to both edge triggered for raising
as well as falling edge interrupt types. See the previous
discussion on patch 3312/1.
Signed-off-by: Mårten Wikström <marten.wikstrom@passito.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds the at91_set_multi_drive() function to enable/disable
the multi-drive (open collector) pin capability on the AT91RM9200
processor.
This is necessary to fix the UDC (USB Gadget) driver for the AT91RM9200
board as it will not allow the board reset line to be pulled low if the
pullup is not driven as an open collector output as the boards are wired
to the USB connector on both the DK/EK.
This version of the patch updates it to 2.6.16-rc4.
Orignal patch by Jeff Warren.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Uli Luckas
This is a bugfix.
The comment in arch/arm/common/rtctime.c explains it:
* FIXME: for now, we just copy the alarm time because we're lazy (and
* is therefore buggy - setting a 10am alarm at 8pm will not result in
* the alarm triggering.)
This patch adds one day to the alarm iff the alarm wrapped beyond midnight and therefore appears to be in the past.
Signed-off-by: Uli Luckas <u.luckas@road-gmbh.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch adds support for the beeper
embedded in the NSLU2 to the machine setup code.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
The power button exit routine for the Linksys NSLU2 was not protected by
a machine_is_nslu2(). This patch fixes it.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The initial code did not configure the inbound memory windows for direct
master access to the SDRAM. This patch creates a 1:1 mapping between the
Versatile/PB PCI memory windows and its SDRAM. Note that an updated FPGA
image is needed for Versatile/PB since the original windows were 1MB and
not able to cover the whole SDRAM (now extended to 256MB). The patch also
fixes the PCI IRQ mapping for slot #2.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Although you could ask the kernel for panic-on-oops, it remained
non-functional because the architecture specific code fragment had
not been implemented. Add it, so it works as advertised.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Commit 99595d0237 forgot to intercept
sys_socketcall as well.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
ARM patch 3226/1 (IXP4xx runtime expansion bus window size configuration)
forgot to update mach-ixp4xx/nslu2-setup.c which leads to the following
compilation error. Update NSLU2 flash support following patch 3226/1.
CC arch/arm/mach-ixp4xx/nslu2-setup.o
arch/arm/mach-ixp4xx/nslu2-setup.c:30: error: ‘NSLU2_FLASH_BASE’ undeclared here (not in a function)
arch/arm/mach-ixp4xx/nslu2-setup.c:31: error: ‘NSLU2_FLASH_SIZE’ undeclared here (not in a function)
make[1]: *** [arch/arm/mach-ixp4xx/nslu2-setup.o] Error 1
make: *** [arch/arm/mach-ixp4xx] Error 2
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
---
nslu2-setup.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A change to the SMP initialisation caused the following oops:
CPU1: Booted secondary processor
CPU1: D VIPT write-back cache
CPU1: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU1: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
<7>Calibrating delay loop... 83.14 BogoMIPS (lpj=415744)
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000001c
...
PC is at enqueue_task+0x1c/0x64
LR is at activate_task+0xcc/0xe4
SMP initialisation now requires cpu_possible_map to be initialised in
setup_arch(). Move this from smp_prepare_cpus() to smp_init_cpus()
and call it from our setup_arch() if CONFIG_SMP is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Define the bits for the two board control latches
that control various items on the H1940 iPAQ.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lucas Correia Villa Real
This patch adds s3c2400.h, fixing the build for the 2410/2440
platforms.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch fixes the low-level IO init for omap2 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch fixes the low-level IO init for omap1 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds the missing cache flushes to common low-level
init that are needed to access the IO region. These flushes
are normally done at the end of devicemaps_init(), but we
need to detect the OMAP core type early.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks