This patch adds callback functions, stop_streaming and job_abort,
to abort or finish any DMA in progress. stop_streaming is called
by videobuf2 framework and job_abort is called by m2m framework.
ST_M2M_PEND state is added to discard the next job.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Horizontal and vertical scaling range are according to the following equations.
If (SRC_Width >= 64 x DST_Width) { Exit(-1); /* Out of Horizontal scale range}
If (SRC_Height >= 64 x DST_Height) { Exit(-1); /* Out of Vertical scale range}
fimc_check_scaler_ratio() is used to check if horizontal and vertical
scale range are valid or not. To use fimc_check_scaler_ratio,
source and destination format should be set by VIDIOC_S_FMT.
And in case of scaling up, it doesn't have to check the scale range.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The main scaler has four SFRs for main scaler ratio depending on FIMC version.
FIMC 4.x has only two SFRs and FIMC 5.x has four SFRs for main scaler.
Those are MainHorRatio, MainHorRatio_ext, MainVerRatio and MainverRatio_ext.
The FIMC 5.x has 15 bit resolution for scaling ratio as below.
{MainHorRatio,MainHorRatio_ext} = {[14:6],[5:0]}.
{MainVerRatio,MainVerRatio_ext} = {[14:6],[5:0]}.
MainHorRatio = CISCCTRL[24:16], MainHorRatio_ext = CIEXTEN[15:10]
MainVerRatio = CISCCTRL[8:0], MainVerRatio_ext = CIEXTEN[5:0]
This patch supports FIMC 4.x and FIMC 5.x using platform_device_id::driver_data.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some color formats are mismatched in s5p-fimc driver.
CIOCTRL[1:0], order422_out, should be set 2b'00 not 2b'11
to use V4L2_PIX_FMT_YUYV. Because in V4L2 standard V4L2_PIX_FMT_YUYV means
"start + 0: Y'00 Cb00 Y'01 Cr00 Y'02 Cb01 Y'03 Cr01". According to datasheet
2b'00 is right value for V4L2_PIX_FMT_YUYV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Map all (0, 90, 180, 270) deg counterclockwise rotation and
horizontal and vertical flip controls to (0, 90) deg rotation,
horizontal and vertical flip transformations available
in the device.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase the input DMA "successive burst count" to default
value 4 to improve DMA performance. Minor cleanup.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prevent VIDIOC_STREAMON failing when s_stream callback is
not implemented by a sensor subdev driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove bus_width from s5p_fimc_isp_info data structure.
Determine camera data bus width based on mediabus pixel format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change s3c_fimc.h header file name to s5p_fimc.h, replace s3c_fimc_*
names with s5p_fimc_*. s3c_fimc need to be reserved for S3C series
and s5p-fimc driver will not cover CAMIF devices in S3C SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conversion to multiplanar color formats and minor cleanup.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Porting to videobuf 2 and minor cleanup.
Separate videobuf_queue_ops are are created for m2m
and capture video nodes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch ports mem2mem test device to videobuf2 framework.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Port memory-to-memory framework to videobuf2 framework.
Add support for multi-planar Video for Linux 2 API extensions to the
memory-to-memory driver framework.
Based on the original patch written by Pawel Osciak.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/videobuf2-core.c: In function ‘__vb2_perform_fileio’:
drivers/media/video/videobuf2-core.c:1638: warning: format ‘%ld’ expects type ‘long int’, but argument 4 has type ‘size_t’
drivers/media/video/videobuf2-core.c:1697: warning: format ‘%ld’ expects type ‘long int’, but argument 2 has type ‘size_t’
drivers/media/video/videobuf2-core.c:1703: warning: format ‘%ld’ expects type ‘long int’, but argument 2 has type ‘size_t’
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a generic file io (read and write) emulator for videobuf2. It uses
MMAP memory type buffers and generic vb2 calls: req_bufs, qbuf and
dqbuf. Video date is being copied from mmap buffers to userspace with
standard copy_to_user() function. To add support for file io the driver
needs to provide an additional callback - read_setup or write_setup. It
should provide the default number of buffers used by emulator and flags.
With these flags one can detemine the style of read() or write()
emulation. By default 'streaming' style is used. With
VB2_FILEIO_READ_ONCE flag one can select 'one shot' mode for read()
emulator. With VB2_FILEIO_WRITE_IMMEDIATE flag one can select immediate
conversion of write calls to qbuf for write() emulator, so the vb2 will
not wait until each buffer is filled completely before queueing it to
the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA scatter/gather allocator and handling
routines for videobuf2.
For mmap operation mode it is implemented on top of
alloc_page + sg_set_page/_free_page.
For userptr operation mode it is implemented on top of
get_user_pages + sg_set_page/put_page.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA coherent memory allocator and handling
routines for videobuf2, implemented on top of dma_alloc_coherent() call.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of contiguous virtual memory allocator and handling
routines for videobuf2, implemented on top of vmalloc()/vfree() calls.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 is a Video for Linux 2 API-compatible driver framework for
multimedia devices. It acts as an intermediate layer between userspace
applications and device drivers. It also provides low-level, modular
memory management functions for drivers.
Videobuf2 eases driver development, reduces drivers' code size and aids in
proper and consistent implementation of V4L2 API in drivers.
Videobuf2 memory management backend is fully modular. This allows custom
memory management routines for devices and platforms with non-standard
memory management requirements to be plugged in, without changing the
high-level buffer management functions and API.
The framework provides:
- implementations of streaming I/O V4L2 ioctls and file operations
- high-level video buffer, video queue and state management functions
- video buffer memory allocation and management
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add multi-planar ioctl handling to the 32bit compatibility layer.
[mchehab@redhat.com: Merged with a fixup patch from Pawel]
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multi-planar API is as a backwards-compatible extension of the V4L2 API,
which allows video buffers to consist of one or more planes. Planes are
separate memory buffers; each has its own mapping, backed by usually
separate physical memory buffers.
Many different uses for the multi-planar API are possible, examples
include:
- embedded devices requiring video components to be placed in physically
separate buffers, e.g. for Samsung S3C/S5P SoC series' video codec,
Y and interleaved Cb/Cr components reside in buffers in different
memory banks;
- applications may receive (or choose to store) video data of one video
buffer in separate memory buffers; such data would have to be temporarily
copied together into one buffer before passing it to a V4L2 device;
- applications or drivers may want to pass metadata related to a buffer and
it may not be possible to place it in the same buffer, together with video
data.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/technisat-usb2.c: In function ‘technisat_usb2_disconnect’:
drivers/media/dvb/dvb-usb/technisat-usb2.c:770: warning: ‘cancel_rearming_delayed_work’ is deprecated (declared at include/linux/workqueue.h:421)
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adding support for Technisat's new USB2.0 DVB-S/S2 receiver
device. The development was sponsored by Technisat.
The Green led is toggle depending on the frontend-state. The Red LED is turned
on all the time.
The MAC address reading from the EEPROM along with the
LRC-method to check whether its valid.
Support for the IR-receiver of the Technisat USB2 box. The keys of
small, black remote-control are built-in, repeated key behaviour are
simulated.
The i2c-mutex of the dvb-usb-structure is used as a general mutex for
USB requests, as there are 3 threads racing for atomic requests
consisting of multiple usb-requests.
A module option is there which disables the toggling of LEDs by the
driver on certain triggers. Useful when being used in a "dark"
environment.
[mchehab@redhat.com: Fix merge conflicts with RC renaming patches]
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some backends want to receive the full transport stream including
uncorrected packets. To have that feature this patchs add a field to
the config-structure called TEI (transport stream error indicator).
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch STV090X adds and exports a function to control the GPIOs of
the stv090x-devices.
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In commit 567aba0b79, the probe address
for tda8290_probe and tda8295_probe was hard-coded to 0x4b, which is the
default i2c address for those devices, but its possible for the device
to be at an alternate address, 0x42, which is the case for the HVR-1950.
If we probe the wrong address, probe fails and we have a non-working
device. We have the actual address passed into the function by way of
i2c_props, we just need to use it. Also fix up some copy/paste comment
issues and streamline debug spew a touch. Verified to restore my
HVR-1950 to full working order.
Special thanks to Ken Bass for reporting the issue in the first place,
and to both he and Gary Buhrmaster for aiding in debugging and analysis
of the problem.
Reported-by: Ken Bass <kbass@kenbass.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's a Realtek combo card reader and IR receiver device with multiple
usb interfaces on it. The mceusb driver is incorrectly grabbing all of
them. This change should make it bind to only interface 2 (patch based
on lsusb output on the linux-media list from Lucian Muresan).
Tested regression-free with the six mceusb devices I have myself.
Reported-by: Patrick Boettcher <pboettcher@kernellabs.com>
Reported-by: Lucian Muresan <lucianm@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CIR Wake FIFO is 67 bytes long, but the stock remote appears to only
populate 65 of them. Limit comparison to 65 bytes, and wake from suspend
works a whole lot better (it wasn't working at all for most folks).
Fix based on comparison with the old lirc_wb677 driver from Nuvoton,
debugging and testing done by Dave Treacy by way of the lirc mailing
list.
Reported-by: Dave Treacy <davetreacy@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The newest variants of the HVR-1600 have an s5h1411/tda18271 for the digital
frontend. Add support for these boards.
Thanks to Hauppauge Computer Works for providing sample hardware.
[awalls@md.metrocast.net: Changed an additional log message to clarify for
the end user that the driver is defaulting to an original HVR-1600 for
unknown model numbers.]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After upgrading the kernel from stock Ubuntu 7.10 to
10.04, with no hardware changes, I started getting the dreaded DMA
TIMEOUT errors, followed by inability to encode until the machine was
rebooted.
I came across a post from Andy in March
(http://www.gossamer-threads.com/lists/ivtv/users/40943#40943) where he
speculates that perhaps the corrective actions being taken after a DMA
ERROR are not sufficient to recover the situation. After some testing
I suspect that this is indeed the case, and that in fact the corrective
action may be what hangs the card's DMA engine, rather than the
original error.
Specifically these DMA ERROR IRQs seem to present with two different
values in the IVTV_REG_DMASTATUS register: 0x11 and 0x13. The current
corrective action is to clear that status register back to 0x01 or
0x03, and then issue the next DMA request. In the case of a 0x13 this
seems to result in a minor glitch in the encoded stream due to the
failed transfer that was not retried, but otherwise things continue OK.
In the case of a 0x11 the card's DMA write engine is never heard from
again, and a DMA TIMEOUT follows shortly after. 0x11 is the killer.
I suspect that the two cases need to be handled differently. The
difference is in bit 1 (0x02), which is set when the error is about to
be successfully recovered, and clear when things are about to go bad.
Bit 1 of DMASTATUS is described differently in different places either
as a positive "write finished", or an inverted "write busy". If we
take the first definition, then when an error arises with state 0x11,
it means that the write did not complete. It makes sense to start a
new transfer, as in the current code. But if we take the second
definition, then 0x11 means "an error but the write engine is still
busy". Trying to feed it a new transfer in this situation might not be
a good idea.
As an experiment, I added code to ignore the DMA ERROR IRQ if DMASTATUS
is 0x11. I.e., don't start a new transfer, don't clear our flags, etc.
The hope was that the card would complete the transfer and issue a ENC
DMA COMPLETE, either successfully or with an error condition there.
However the card still hung.
The only remaining corrective action being taken with a 0x11 status was
then the write back to the status register to clear the error, i.e.
DMASTATUS = DMASTATUS & ~3. This would have the effect of clearing the
error bit 4, while leaving the lower bits indicating DMA write busy.
Strangely enough, removing this write to the status register solved the
problem! If the DMA ERROR IRQ with DMASTATUS=0x11 is completely
ignored, with no corrective action at all, then the card will complete
the transfer and issue a new IRQ. If the status register is written to
when it has the value 0x11, then the DMA engine hangs. Perhaps it's
illegal to write to
DMASTATUS while the read or write busy bit is set? At any rate, it
appears that the current corrective action is indeed making things
worse rather than better.
I put together a patch that modifies ivtv_irq_dma_err to do the
following:
- Don't write back to IVTV_REG_DMASTATUS.
- If write-busy is asserted, leave the card alone. Just extend the
timeout slightly.
- If write-busy is de-asserted, retry the current transfer.
This has completely fixed my DMA TIMEOUT woes. DMA ERR events still
occur, but now they seem to be correctly handled. 0x11 events no
longer hang the card, and 0x13 events no longer result in a glitch in
the stream, as the failed transfer is retried. I'm happy.
I've inlined the patch below in case it is of interest. As described
above, I have a theory about why it works (based on a different
interpretation of bit 1 of DMASTATUS), but I can't guarantee that my
theory is correct. There may be another explanation, or it may be a
fluke. Maybe ignoring that IRQ entirely would be equally effective?
Maybe the status register read/writeback sequence is race condition if
the card changes it in the mean time? Also as I am using a PVR-150
only, I have not been able to test it on other cards, which may be
especially relevant for 350s that support concurrent decoding.
Hopefully the patch does not break the DMA READ path.
Mike
[awalls@md.metrocast.net: Modified patch to add a verbose comment, make minor
brace reformats, and clear the error flags in the IVTV_REG_DMASTATUS iff both
read and write DMA were not in progress. Mike's conjecture about a race
condition with the writeback is correct; it can confuse the DMA engine.]
[Comment and analysis from the ML post by Michael <mike@rsy.com>]
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the probing of cx2583x chips, because two controls were clustered
that are not created for these chips.
This regression was introduced in 2.6.36.
Signed-off-by: Sven Barth <pascaldragon@googlemail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous revert-commit, that affected cx23885-i2c.c, left some
unused labels that the compiler griped about. Clean them up.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 44835f197b.
With the CX23885 hardware I2C master, checking for I2C slave ACK/NAK
is not valid when the I2C_EXTEND or I2C_NOSTOP bits are set.
Revert the commit that checks for I2C slave ACK/NAK on all transactions,
so that XC5000 tuners work with the CX23885 again.
Thanks go to Mark Zimmerman for reporting and bisecting this problem.
Bisected-by: Mark Zimmerman <markzimm@frii.com>
Reported-by: Mark Zimmerman <markzimm@frii.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the pid filtering for the dib7000M demod. It also
corrects the pid filtering for the dib7700 based board. It should
prevent an oops, when using dib7700p based board.
References: https://bugzilla.novell.com/show_bug.cgi?id=644807
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Tested-by: Pavel SKARKA <paul.sp@seznam.cz>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current matching rules the lookup for rc protocol named rc-5-sz matches with "rc-5" before finding "rc-5-sz". Thus one is able to never enable/disable the rc-5-sz protocol via sysfs.
Fix the lookup to require an exact match which allows the manipulation of sz protocol.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] fix saa7111 non-detection
[media] rc/streamzap: fix reporting response times
[media] mceusb: really fix remaining keybounce issues
[media] rc: use time unit conversion macros correctly
[media] rc/ir-lirc-codec: add back debug spew
[media] ir-kbd-i2c: improve remote behavior with z8 behind usb
[media] lirc_zilog: z8 on usb doesn't like back-to-back i2c_master_send
[media] hdpvr: fix up i2c device registration
[media] rc/mce: add mappings for missing keys
[media] gspca - zc3xx: Discard the partial frames
[media] gspca - zc3xx: Fix bad images with the sensor hv7131r
[media] gspca - zc3xx: Bad delay when given by a table
au0828: fix VBI handling when in V4L2 streaming mode
It turns up V4L2 streaming mode (a.k.a mmap) was broken for VBI streaming.
This was causing libzvbi to fall back to V4L1 capture mode, and is a blatent
violation of the V4L2 specification.
Make the implementation work properly in this mode.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 4651918a4a changed the way events
are stored. However, it forgot to fix ir_raw_event_store_edge() to work
with the new way. Due to that, the decoders will likely do bad things.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change for firmware re-loading and updated firmware versions.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_device is already being freed in video_device.release callback on
release.
Signed-off-by: Pawel Osciak <pawel@osciak.com>
Reported-by: Roland Kletzing <devzero@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver Version v1.75 Kernel oops appears in 2.6.37-rc8 in
lme_firmware_switch because of a memcpy to a const char.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
One saa7111 device is reporting a different ID:
saa7115 0-0024: chip found @ 0x48 (ID 0f7111d0e111111) does not match a known saa711x chip.
As this is for sure a saa7111, change the detection code to also
cover this device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The streamzap driver has relatively low sampling resolution, and any
delays in reporting events seem to cause some minor problems for the
likes of irw when using the lirc bridge driver, resulting in a single
keypress registering as multiple independent ones, rather than as a
single press with repeats. If we call ir_raw_event_handle() more
frequently and reset the rawir kfifo at end-of-signal, the behavior
improves quite a bit.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure rawir struct is zeroed out before populating it for each
ir_raw_event_store_with_filter() call, and when we see a trailing 0x80
packet (end-of-data), issue an ir_raw_event_reset() call.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to my own stupidity, some of the wrong time unit conversion macros
were being used inside some of the IR drivers I've been working on. Fix
that, and convert over some additional places to also use the macros.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some occasionally useful debug spew disappeared as part of a feature
update a while back, and I'm finding myself in need of it again to help
diagnose some issues.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the same "are you ready?" i2c_master_send() poll command to
get_key_haup_xvr found in lirc_zilog, which is apparently seen in
the Windows driver for the PVR-150 w/a z8. This stabilizes what is
received from both the HD-PVR and HVR-1950, even with their polling
intervals at the default of 100, thus the removal of the custom
260ms polling_interval in pvrusb2-i2c-core.c.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mike Isely <isely@isely.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have to actually call i2c_new_device() once for each of the rx and tx
addresses. Also improve error-handling and device remove i2c cleanup.
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per http://mediacenterguides.com/book/export/html/31 and investigation
by Erin, we were missing these last three mappings to complete the mce
key table. Lets remedy that.
Reported-by: Erin Simonds <fisslefink@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases, some frames may not end with the JPEG end of frame.
Being not complete, they are now discarded.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem was introduced by the commit 2af0b4c60c.
Some registers were no more initialized.
Tested-by: <Giovanni Scafora giovanni@archlinux.org>
Tested-by: <Sergey Manucharian sm@ingeniware.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not respond with -EINVAL to EVIOCGKEYCODE for not-yet-mapped
scancodes, but rather return KEY_RESERVED.
This fixes breakage with Ubuntu's input-kbd utility that stopped
returning full keymaps for remote controls.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (101 commits)
[media] staging/lirc: fix mem leaks and ptr err usage
[media] hdpvr: reduce latency of i2c read/write w/recycled buffer
[media] hdpvr: enable IR part
[media] rc/mceusb: timeout should be in ns, not us
[media] v4l2-device: fix 'use-after-freed' oops
[media] v4l2-dev: don't memset video_device.dev
[media] zoran: use video_device_alloc instead of kmalloc
[media] w9966: zero device state after a detach
[media] v4l: Fix a use-before-set in the control framework
[media] v4l: Include linux/videodev2.h in media/v4l2-ctrls.h
[media] DocBook/v4l: update V4L2 revision and update copyright years
[media] DocBook/v4l: fix validation error in dev-rds.xml
[media] v4l2-ctrls: queryctrl shouldn't attempt to replace V4L2_CID_PRIVATE_BASE IDs
[media] v4l2-ctrls: fix missing 'read-only' check
[media] pvrusb2: Provide more information about IR units to lirc_zilog and ir-kbd-i2c
[media] ir-kbd-i2c: Add back defaults setting for Zilog Z8's at addr 0x71
[media] lirc_zilog: Update TODO.lirc_zilog
[media] lirc_zilog: Add Andy Walls to copyright notice and authors list
[media] lirc_zilog: Remove useless struct i2c_driver.command function
[media] lirc_zilog: Remove unneeded tests for existence of the IR Tx function
...
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current hdpvr code kmalloc's a new buffer for every i2c read and
write. Rather than do that, lets allocate a buffer in the driver's
device struct and just use that every time.
The size I've chosen for the buffer is the maximum size I could
ascertain might be used by either ir-kbd-i2c or lirc_zilog, plus a bit
of padding (lirc_zilog may use up to 100 bytes on tx, rounded that up
to 128).
Note that this might also remedy user reports of very sluggish behavior
of IR receive with hdpvr hardware.
v2: make sure (len <= (dev->i2c_buf)) [Jean Delvare]
Reported-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of things going on here, but the end result is that the IR part
on the hdpvr gets enabled, and can be used with ir-kbd-i2c and/or
lirc_zilog.
First up, there are some conditional build fixes that come into play
whether i2c is built-in or modular. Second, we're swapping out
i2c_new_probed_device() for i2c_new_device(), as in my testing, probing
always fails, but we *know* that all hdpvr devices have a z8 chip at
0x70 and 0x71. Third, we're poking at an i2c address directly without a
client, and writing some magic bits to actually turn on this IR part
(this could use some improvement in the future). Fourth, some of the
i2c_adapter storage has been reworked, as the existing implementation
used to lead to an oops following i2c changes c. 2.6.31.
Earlier editions of this patch have been floating around the 'net for a
while, including being patched into Fedora kernels, and they *do* work.
This specific version isn't yet tested, beyond loading ir-kbd-i2c and
confirming that it does bind to the RX address of the hdpvr.
[mchehab@redhat.com: I2C_CLASS_TV_ANALOG is not defined. Fix compilation bug]
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes an egregious bug in mceusb driver, where the receiver was being
put into idle mode far sooner than it should have, thanks to storing a
timeout value that in us where it should be ns. Basically, the receiver
kept going into idle mode before a trailing space had been fully
received, which was causing problems for some protocols, most notably
manifesting as lirc userspace never receiving a trailing space for any
rc5 signals.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a bug in v4l2_device_unregister where the sd pointer can be dereferenced
after it was freed.
Normally the i2c adapter is removed before this function is called. Removing
the adapter will also unregister all subdevs on that adapter, so generally
v4l2_device_unregister has nothing to do. However, in the case of a platform
i2c bus that bus is generally not freed.
In that case, after freeing the i2c subdevice the code will fall into the
second block when it tests if the subdev is a SPI device. But by that time
the subdev is already freed and the kernel oopses.
The fix is trivial: continue with the loop after freeing the i2c or spi
subdevice.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Zeroing video_device.dev causes a memory leak if video_set_drvdata
was called before video_register_device was called. video_set_drvdata
calls dev_set_drvdata which allocates video_device.dev.p.
memsetting this will prevent freeing of that memory.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After a detach zero the whole device state to ensure a clean slate
on the next attach.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_queryctrl sets the step value based on the control type. That would
be fine if it used the control type stored in the V4L2 kernel control
object, not the one stored in the userspace ioctl structure that has
just been memset to 0. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When queryctrl is called with a V4L2_CID_PRIVATE_BASE control ID, then
currently it is replaced by the real internal ID. This is not according to
the spec so keep the V4L2_CID_PRIVATE_BASE ID in this case.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_CTRL did not check against read-only controls. Even worse, for
controls of type CTRL_CLASS it would cause a kernel oops since those controls
do not have a s_ctrl op.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When registering an IR Rx device with the I2C subsystem, provide more detailed
information about the IR device and default remote configuration for the IR
driver modules.
Also explicitly register any IR Tx device with the I2C subsystem.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts a portion of commit
44243fc2ef
A commit for which I errantly recommended that defaults for I2C address
0x71 not be set by ir-kbd-i2c.c
The pvrusb2 and bttv drivers currently rely on ir-kbd-i2c setting
defaults for that address. Until I can get those bridge drivers fixed
to properly send IR_i2c_init_data for boards with Zilog Z8 chips,
just add back the default settings for I2C address 0x71.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After a recent update of xf86-input-evdev and xorg-server, I noticed
that X11 applications did not receive keypresses from the FireDTV
infrared remote control anymore. Instead, the Xorg log featured lots of
"FireDTV remote control: dropping event due to full queue!"
exclamations. The Linux console did not have an issue with the
FireDTV's RC though.
The fix is to insert EV_SYN events after the key-down/-up events.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit e3c9221519 ("[media] radio-aimslab.c: Fix
gcc 4.5+ bug") removed the include, but introduced new callers of msleep():
| drivers/media/radio/radio-aimslab.c: In function ‘rt_decvol’:
| drivers/media/radio/radio-aimslab.c:76: error: implicit declaration of function ‘msleep’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix sparse warning for non-ANSI function declaration:
drivers/media/rc/ir-raw.c:247:30: warning: non-ANSI function declaration of function 'ir_raw_get_allowed_protocols'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds s_power support to adv7175 driver. Power-down is done
by power-down all four DACs.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
info->num comes from the user. It's type int. If the user passes
in a negative value that would cause memory corruption.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My initial thinking was that we should default to mouse mode, so people
could use the mouse function to click on something on a login screen,
but a lot of systems where a remote is useful automatically log in a
user and launch a media center application, some of which hide the
mouse, which can be confusing to users if they punch buttons on the
remote and don't see any feedback. Plus, first and foremost, its a
remote, so lets default to being a remote, and only toggle into mouse
mode when the user explicitly asks for it. As a nice side-effect, this
actually simplifies some of the code a fair bit...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ene_ir driver was using a private define of MS_TO_NS, which is meant
to be microseconds to nanoseconds. The mceusb driver copied it,
intending to use is a milliseconds to microseconds. Lets move the
defines to a common location, expand and standardize them a touch, so
that we now have:
MS_TO_NS - milliseconds to nanoseconds
MS_TO_US - milliseconds to microseconds
US_TO_NS - microseconds to nanoseconds
Reported-by: David Härdeman <david@hardeman.nu>
CC: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise, we have a null receive buffer, and the logic all falls down,
goes boom, all ffdc devs wind up as imon IR w/VFD. Oops.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dev->rdev is accessed in ene_setup_hw_settings, so it needs to be wired
up before then.
[Jarod Wilson]: Also fix a possible improper resource freeing bug while
we're looking at possible probe issues here.
Signed-off-by: Kyle McMartin <kmcmartin@redhat.com>
CC: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's a nasty bug that slipped in when the rc device interface was
altered, only affecting the older 0xffdc imon devices. We were trying
to access ictx->rdev->allowed_protos before ictx->rdev had been set.
There's also an issue with call ordering that meant the correct
keymap wasn't getting loaded for MCE IR type 0xffdc devices.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use unlocked_ioctl in v4l2_file_operations. The locking is
already in place.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With cmwq, there's no reason to use separate out_work_queue. Drop it
and use system_wq instead. The in_work_queue needs to be ordered so
can't use one of the system wqs; however, as it isn't used to reclaim
memory, allocate the workqueue with alloc_ordered_workqueue() without
WQ_MEM_RECLAIM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
While reading
drivers/media/video/tlg2300/pd-video.c::alloc_bulk_urbs_generic() I
noticed that
- We don't free the memory allocated to 'urb' if the call to
usb_alloc_coherent() fails.
- If the 'num' argument to the function is ever <= 0 we'll return an
uninitialized variable 'i' to the caller.
The following patch addresses both of the above by a) calling
usb_free_urb() when usb_alloc_coherent() fails and by explicitly
initializing 'i' to zero.
I also moved the variables 'mem' and 'urb' inside the for loop. This does
not actually make any difference, it just seemed more correct to me to let
variables exist only in the innermost scope they are used.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We may leak the storage allocated to 'state' in
drivers/media/dvb/frontends/ix2505v.c::ix2505v_attach() on error, as
it is too early to be able to call ix2505v_release().
This patch makes sure we free the allocated memory in the failure case.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The infrared was set by sensor write instead of bridge GPIO.
It is now settable by the standard control ILLUMINATOR_1.
A module parameter permits to set the right GPIO bit according
to the StarCam model.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__devinit* must not be used in USB drivers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Renamed has_new to is_new.
Drivers can use the is_new field to determine if a new value was specified
for a control. The v4l2_ctrl_handler_setup() must always set this to 1 since
the setup has to force a full update of all controls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some subdevs need to call into the board code after they are registered
and have a valid struct v4l2_device pointer. The s_config op was abused
for this, but now that it is removed we need a cleaner way of solving this.
So this patch adds a struct with internal ops that the v4l2 core can call.
Currently only two ops exist: register and unregister. Subdevs can implement
these to call the board code and pass it the v4l2_device pointer, which the
board code can then use to get access to the struct that embeds the
v4l2_device.
It is expected that in the future open and close ops will also be added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The core.s_config op was meant for legacy drivers that needed to work with old
pre-2.6.26 kernels. This is no longer relevant. Unfortunately, this op was
incorrectly called from several drivers.
Replace those occurences with proper i2c_board_info structs and call
v4l2_i2c_new_subdev_board.
After these changes v4l2_i2c_new_subdev_cfg() was no longer used, so remove
that function as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some weird bugs at tda8290/tda18271 initialization, as it
insits do do analog initialization during DVB frontend attach:
DVB: registering new adapter (saa7133[0])
DVB: registering adapter 0 frontend 0 (Fujitsu mb86A20s)...
mb86a20s: mb86a20s_initfe
tda18271_write_regs: [2-0060|M] ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5
tda18271_init: [2-0060|M] error -5 on line 830
tda18271_tune: [2-0060|M] error -5 on line 908
tda18271_write_regs
tda18271_write_regs: [2-0060|M] ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5
tda18271c2_rf_tracking_filters_correction: [2-0060|M] error -5 on line 265
tda18271_write_regs
tda18271_write_regs: [2-0060|M] ERROR: idx = 0x25, len = 1, i2c_transfer returned: -5
tda18271_channel_configuration: [2-0060|M] error -5 on line 119
tda18271_set_analog_params: [2-0060|M] error -5 on line 1045
tda18271_set_analog_params: [2-0060|M] error -5 on line 1045
tda829x 2-004b: tda8295 not locked, no signal?
tda829x 2-004b: tda8295_i2c_bridge: disable i2c gate
tda829x 2-004b: tda8295 not locked, no signal?
tda829x 2-004b: tda8295_i2c_bridge: disable i2c gate
mb86a20s_i2c_writereg: writereg error (rc == -5, reg == 0x29, data == 0x33)
mb86a20s: Init failed. Will try again later
The problem is that mb86a20s is only visible if the analog part is disabled.
However, due to a trick at mb86a20s, it will later initialize properly:
mb86a20s: mb86a20s_initfe: Initialization succeded.
This is hacky and ugly. However, I coldn't find any easy way to fix it.
A proper fix would be to have a resource locking schema, used by both
V4L and DVB parts that would block access to analog registers while
digital registers are in use, but this will probably put tda829x into
a dead lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were some issues at tda8290 that were preventing this device
to work. Now that those fixes were fixed, we can enable analog
mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to a hard to track bug between tda829x/tda18271/saa7134, tda829x
wants to go to analog mode during DVB initialization, causing some
I2C errors.
The analog failure doesn't cause any harm, as the device were already
properly initialized in analog mode. However, the failure at the digital
mode causes the frontend mb86a20s to not initialize. Fortunately, at
least on my tests, it was possible to detect that the device is a
mb86a20s before the failure.
What happens is that tda8290 is a very bad boy: during DVB setup, it
keeps insisting to call tda18271 analog_set_params, that calls
tune_agc code. The tune_agc code calls saa7134 driver, changing the
value of GPIO 27, switching from digital to analog mode and disabling
the access to mb86a20s, as, on Kworld SBTVD, the same GPIO used
to switch the hardware AGC mode seems to be used to enable the I2C
switch that allows access to the frontend (mb86a20s).
So, a call to analog_set_params ultimately disables the access to
the frontend, and causes a failure at the init frontend logic.
This patch is a workaround for this issue: it simply checks if the
frontend init had any failure. If so, it will init the frontend when
some DTV application will try to set DVB mode.
Even being a hack for Kworld SBTVD to work, and assumning that we could
teach tda8290 to be a good boy, this is actually an improvement at the
frontend driver, as it will be more reliable to initialization failures.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A script replaced err var to rc. Howerver, this script gambled
"error" string, changing it to "rcor". Revert that bad change.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Kworld SBTVD, tda8295-c1 starts in power off mode. It needs
to be powered, otherwise, the I2C gate control command won't work.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Read operations should be preceeded by a write operation. However,
nothing prevents that an I2C operation could happen between the two
transactions.
To avoid that problem, use an unique I2C transfer for both parts of
the I2C transaction.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to a lack of a break inside the switch, it were getting the
wrong keytable and get_key function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes Fedora 14 bug: https://bugzilla.redhat.com/show_bug.cgi?id=667157
There are a few bugs at the code that generates the scancode at dib0700:
- RC keycode is wrong (it outputs a 24 bits keycode);
- NEC extended outputs a keycode that have endiannes issues;
- keycode tables for NEC extended remotes need to be updated.
The last issue need to be done as we get reports, as we don't have
the complete NEC-extended keycodes at the dibcom table.
This patch fixes the first two issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The si470x i2c and usb driver support the RDS, so this ifdef statement
doesn't need more.
[mchehab@redhat.com: Fix a conflict on it]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ioctls VIDIOC_DBG_S_REGISTER and VIDIOC_DBG_G_REGISTER should return -EINVAL
if the driver didn't implement them. Currently they return -EPERM if called as
non-root user. However, this check should only be done if the driver actually
implemented these ioctls. Otherwise, just return -EINVAL as we do with all
unimplemented ioctls.
This bug make the v4l2-compliance test suite fail.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While going through windows inf file I found more usb-id, add a comment
with this id for future reference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looking at the windows inf file, for usb ids with a sensor type where probing
is needed to determine the type (for example ov7630 or soi768), this is
needed for all bridge variants with a usb id indicating this sensor type.
So do the probing to determine the actual sensor type for types where the
usb-id info is not 100% deterministic, independent of the bridge type.
If you look through the list of currently active usb ids in sonixj, this
effectively only changes the code path for 0c45:60fe (sn9c105 + ov7630) and
0c45:612e (sn9c110 + ov7630), which according to the inf file can have a
soi768 instead of a ov7630 just like the sn9c120 + ov7630 models where we
already probe for a soi7630.
The main reason for this code change is to keep the code paths as bridge
variant independent as possible, so that we don't need a lot of special
per bridge cases, as we enable more usb-ids in the future.
This change makes the 0c45:60fe code path identical to the successfully
tested 0c45:613e, so also make sonixj the default driver for 0c45:60fe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both we and the windows driver make no sensor specific differences
(with some exceptions) for different sonixj bridge types. Thus if a
sn9c105 bridge has been successfully tested with a sensor, the same
sensor can be successfully used with a sn9c120 bridge too.
Using this knowledge we can move over most usb-ids too the sonixj
driver when both are compiled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that our bridge code is unified for sn9c101/102 and sn9c103 models,
the sn9c103 models should simply work, given that the only difference
in the sn9c103 is audio support and a gamma correction table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also fix the issue of the image being mirrored.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refactor the code to unify how the sn9c101/102 and the sn9c103 bridge
are handled. Also move code which is the same for all sensors from
the per sensor init register settings to a central place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sn9c102 driver claims a number of usb-ids which are for cameras
with sensor types which it does not support. Also it claims a number
of usb-ids which do not exist at all (not present in the windows
drivers .inf files, not known by google).
This patch also fixes the conflict with the gspca_sonixj driver for the
0c45:60c0 and 0c45:60fb usb ids.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The et61x251 driver claims a whole list of usb id's, but it only has
one sensor "module" which does sensor detection based on usb id and that
only supports devices with the 102c:6251 usb id. Remove the usb-ids for
other devices as for those the driver will fail with an unable to determine
sensor type message anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We check for not streaming as a condition to abort waiting in dqbuf, so
when another thread does a streamoff we should wake the wq.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some applications (xawtv, qv4l2) mix read and mmap calls. Allow switching
from read mode back to mmap mode (by doing a reqbufs).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_dev->memory == GSPCA_MEMORY_NO implies gspca_dev->nframes == 0,
so there is no need to check for both in dev_poll. The check in
dev_read also is more complex then needed, as dqbuf which dev_read
calls already does all necessary checks. Moreover dqbuf is holding
the proper locks while checking where as dev_read itself is not.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch we were not setting the memory type to GSPCA_MEMORY_NO
when the buffers were released by the app doing a reqbufs 0. Nor would
the memory type be set to GSPCA_MEMORY_NO on device close, as capture_file
already is NULL on device close because of the reqbufs 0. This caused the
following problem:
-app1 does reqbufs USERPTR for 4 buffers
-app1 does reqbufs USERPTR for 0 buffers
-app2 tries to do reqbufs MMAP for 4 buffers
fails because gspca_dev->memory still is USERPTR
Fixing this also allows an app to switch memory type's by unrequesting
the buffers and re-requesting them of a different type.
This patch also moves the setting of gspca_dev->frsz and gscpa_dev->memory
to after alloc_frame succeeding, so that they are not changed when allocating
fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the no longer used / useful users variable, and with that gone
there also is no longer a need to take queue_lock in dev_open.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch dqbuf errors out on a failing user_copy (with user pointers)
before updating the buffer flags, causing a successsfully dequeued buffer
to still have the DONE flag, which means that it could no longer be
re-queueud (assuming the app somehow survives the segfault).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch vidioc_dqbuf is using its own read_lock, where as
other queue related functions use queue_lock. This means that dqbuf is
accessing several variables in a racy manor. The most important one
being fr_o, which may be changed from underneath dqbuf by vidioc_reqbufs
or vidioc_streamoff. Other variables which it accesses unprotected
are gspca_dev->memory, gspca_dev->streaming and gspca_dev->capt_file.
This patch fixes this by changing vidioc_dqbuf to also use the queue_lock.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The gspca_dev->streaming boolean is protected against multiple access
through gspca_dev->queue_lock everywhere except for 2 places. This patch
fixes this by bringing it under the lock in vidioc_streamoff. And by
removing the check for gspca_dev->streaming in gspca_disconnect,
the destroy_urbs call may be called multiple times (and is protected
by the usb_lock) and calling wake_up_interruptible can also always be done
safely.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IF freq for DVB-T 7 MHz and 8 MHz was set slightly wrong. Due to that it
didn't worked at all (?) for 7 MHz channels and most likely performance
was dropped for 8 MHz channels.
That bug was pointed by few people during last two months. Thank you.
Trivial fix. Compile tested only due to lack of proper HW and signal.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Romolo Manfredini <romoloman@hotmail.com>
Cc: Alireza Moini <alireza.moini@silverbrookresearch.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The radio-gemtek-pci driver is for the same hardware as the radio-maxiradio
driver which uses the same GemTek PR103 and tea5757 combination and the two
drivers are identical. I chose the maxiradio over the gemtek-pci driver since
the maxiradio has support for mono/stereo detection.
Tested with my gemtek-pci card.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the standard USA/Europe frequency range of 87-108 MHz instead of the
arbitrary 50-150 MHz.
Copied from the radio-gemtek-pci driver which supports the same hardware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added functions to set and get custom DV timings.
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Added functions to set/get/query/enum DV presets for vpif_caputre and
vpif_display.
- The format specification table is extended with all the DV formats
supported by TVP7002.
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- The ch_params tables in vpif_capture.c and vpif_display.c are moved to a common
table in vpif.c. Then it is easier to maintain the table.
- The field "fps" is removed from the struct vpif_channel_config_params because it
is not used.
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by : Murali Karicheri <mkaricheri@gmail.com>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert saa7146 to use core-assisted locking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since tda9875 is part of tvaudio this field no longer makes sense. Remove it.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In commit 411674fd18 the tda9875 support was
added to tvaudio. This means that tda9875 is no longer used since mid-2009.
If there are out-of-tree users of this driver, then they can switch to tvaudio
instead.
The original commit message read as follows:
This change allows bttv to use tvaudio for this device. Since this device
has the same i2c address as the tda9874 we need to support both in the same
tvaudio driver. This makes it possible for tvaudio to detect which chip is
used. Originally the tda9875 was only available in the dedicated tda9875
driver, but that makes life very hard for bttv since loading tvaudio might
misdetect a tda9875 as a tda9874.
So there were good reasons for moving the tda9875 code into tvaudio.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
gcc 4.5+ doesn't properly evaluate some inlined expressions.
A previous patch were proposed by Andrew Morton using noinline.
However, the entire inlined function is bogus, so let's just
remove it and be happy.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/v4l2-compat-ioctl32.c: In function 'get_v4l2_format32':
drivers/media/video/v4l2-compat-ioctl32.c:169:2: warning: case value '0' not in enumerated type 'enum v4l2_buf_type'
drivers/media/video/v4l2-compat-ioctl32.c: In function 'put_v4l2_format32':
drivers/media/video/v4l2-compat-ioctl32.c:200:2: warning: case value '0' not in enumerated type 'enum v4l2_buf_type'
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/zoran/zoran_driver.c: In function 'zoran_dqbuf':
drivers/media/video/zoran/zoran_driver.c:2197:21: warning: 'bs.frame' may be used uninitialized in this function
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/common/tuners/tda18218.c: In function 'tda18218_wr_regs':
drivers/media/common/tuners/tda18218.c:58:5: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
em28xx uses core assisted locking, so it shouldn't use .ioctl.
The .ioctl callback was replaced by .unlocked_ioctl for video nodes,
but not for radio nodes. This is now corrected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that cx88 and ivtv use wm8775 on some different modes. The
patch that added support for a board with wm8775 broke ivtv boards with
this device. As we're too close to release 2.6.37, let's just revert
it.
Reported-by: Andy Walls <awalls@md.metrocast.net>
Reported-by: Eric Sharkey <eric@lisaneric.org>
Reported-by: Auric <auric@aanet.com.au>
Reported by: David Gesswein <djg@pdp8online.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a regression that crept into 2.6.36.
The volume control scale in the cx25840 driver has an unusual mapping
from register values to v4l2 volume control values. Enforce the mapping
limits, so that the default volume control setting does not fall out of
bounds to prevent the cx25840 module device probe from failing.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on Waling Dijkstra's discovery that the IR works the same as
on the TT-1500, this patch has been rewritten to fit with the
rc_core infrastructure.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixing the problem with NEC protocol and repeating keys under the following
circumstances. The problem occurs when there is a repeat code without
properly decoded scancode. This leads to repeat the wrong (last decoded)
scancode.
An example from real life:
I am pressing volume down, then several minutes later i am pressing
volume up, but the real scancode is wrongly decoded and only a repeat
event is emitted, so as a result volume is going down while i am holding
volume up button.
The patch fixes above problem using rc_keyup timeout (as pointed by Mauro).
It just prevents key repeats if they appear after rc_keyup.
Signed-off-by: Mariusz Białończyk <manio@skyboo.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In certain machines, camera devices are supplied directly
by a number of regulators. This patch add the ability to drive
these regulators directly by the soc_camera driver.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the V4L mutex infrastructure in soc-camera core and drivers and switch to
.unlocked_ioctl.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a more direct way to obtain a pointer to struct ov772x_priv, where the
subdevice is available.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OmniVision OV9640 driver wasn't requesting properly its private data
on I2C remove and video_probe functions. It was retrieving the V4L2
subdev struct address instead of priv struct's one. This patch fixes
such problem.
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix two gcc warnings:
drivers/media/video/ivtv/ivtv-i2c.c:170: warning: cast from pointer to integer of different size
drivers/media/video/ivtv/ivtv-i2c.c:171: warning: cast from pointer to integer of different size
$ gcc --version
gcc (GCC) 4.1.2 20080704 (Red Hat 4.1.2-48)
They seem bogus, but, as the original code also has problems with
LE/BE, just change its implementation to be clear.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds I2C registration of the Zilog Z8F0811 IR microcontroller for either
lirc_zilog or ir-kbd-i2c to use. This is a required step in removing
lirc_zilog's use of the deprecated struct i2c_adapter.id field.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Zilog IR entries are already handled by IR new code. So,
remove its usage from the legacy IR support.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
lirc-i2c implements a get key logic for the Adaptec Remote
Controller, at address 0x6b. The only driver that seems to have
an Adaptec device is ivtv:
$ git grep -i adaptec drivers/media
drivers/media/video/cs53l32a.c: * cs53l32a (Adaptec AVC-2010 and AVC-2410) i2c ivtv driver.
drivers/media/video/cs53l32a.c: * Audio source switching for Adaptec AVC-2410 added by Trev Jackson
drivers/media/video/cs53l32a.c: /* Set cs53l32a internal register for Adaptec 2010/2410 setup */
drivers/media/video/ivtv/ivtv-cards.c:/* Adaptec VideOh! AVC-2410 card */
drivers/media/video/ivtv/ivtv-cards.c: { PCI_DEVICE_ID_IVTV16, IVTV_PCI_ID_ADAPTEC, 0x0093 },
drivers/media/video/ivtv/ivtv-cards.c: .name = "Adaptec VideOh! AVC-2410",
drivers/media/video/ivtv/ivtv-cards.c:/* Adaptec VideOh! AVC-2010 card */
drivers/media/video/ivtv/ivtv-cards.c: { PCI_DEVICE_ID_IVTV16, IVTV_PCI_ID_ADAPTEC, 0x0092 },
drivers/media/video/ivtv/ivtv-cards.c: .name = "Adaptec VideOh! AVC-2010",
drivers/media/video/ivtv/ivtv-cards.h:#define IVTV_CARD_AVC2410 7 /* Adaptec AVC-2410 */
drivers/media/video/ivtv/ivtv-cards.h:#define IVTV_CARD_AVC2010 8 /* Adaptec AVD-2010 (No Tuner) */
drivers/media/video/ivtv/ivtv-cards.h:#define IVTV_PCI_ID_ADAPTEC 0x9005
drivers/media/video/ivtv/ivtv-driver.c: "\t\t\t 8 = Adaptec AVC-2410\n"
drivers/media/video/ivtv/ivtv-driver.c: "\t\t\t 9 = Adaptec AVC-2010\n"
drivers/media/video/ivtv/ivtv-i2c.c: 0x6b, /* Adaptec IR */
There are two Adaptec cards defined there, but AVC-2010 doesn't have a
remote controller. So, the logic at lirc_i2c seems to be for Adaptec AVC-2410.
As we'll remove lirc_i2c from kernel, move the getkey code to ivtv driver, and
use it for AVC-2410.
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, lirc-i2c has a decoding logic for Leadtek Remote
Control. Move it to cx88, as we intend to remove lirc-i2c.
For now, initialize LIRC remote keytable with RC_MAP_EMPTY, as
we don't know its keymap yet. It would be nice to later check
if is there any file on LIRC userspace with that keytable.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When comparing lirc-i2c and ir-kbd-i2c/bttv-input logic, a difference
was noticed. As lirc-i2c will be removed soon, store the difference on
a comment inside ir-kbd-i2c, in order to preserve the knowledge we
have about that remote controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix 64-bit compile warning:
drivers/media/video/timblogiw.c: In function ‘timblogiw_dma_filter_fn’:
drivers/media/video/timblogiw.c:151: warning: cast from pointer to integer of different size
drivers/media/video/timblogiw.c: In function ‘timblogiw_open’:
drivers/media/video/timblogiw.c:670: warning: cast to pointer from integer of different size
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Richard Rojförs <richard.rojfors@pelagicore.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l core sets the v4l2_input.capabilities field based on the supplied
v4l2_ioctl_ops. However, several drivers do a memset or memcpy of the v4l2_input
struct, thus overwriting that field incorrectly.
Either remove the memset (which is already done by the v4l core), or add the
proper capabilities field in case of a memcpy.
The same is also true for v4l2_output, but that only affected the ivtv driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Calling subdevs to handle s_ctrl returned a non-zero return code even if
everything went fine.
Calling STREAMOFF if no STREAMON happened earlier would hit a BUG_ON
in res_free.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'def' field is only valid for menus, integers and booleans.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prevents checkpatch warnings generated when defining
'static const char *foo[]' arrays. It makes sense to use
const char * const * anyway since the pointers in the array
are indeed const.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert driver to use core-assisted locking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The naming of the media/rds.h header suggested that it was a generic
RDS header, when in fact it is just a saa6588 module API that is
internal to the kernel.
Rename the header and the struct and defines in it to make this clear.
Also removed the header include in radio-si470x.h (not used anymore)
and from ioctl-number.txt (it's internal to the kernel and never called
from userspace).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use put_device() instead of kfree() because of device name leak.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some comments:
1. Everything initialize properly except radio.
2. All analog inputs (TV, composite, S-Video) are tested by myself in several
TV norms (SECAM-D, PAL, NTSC), everything work fine.
So the patch adds general support/detection of the card with working analog
part, DVB part is not supported for now.
Signed-off-by: Alexey Chernov <4ernov@gmail.com>
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A Hauppauge HVR 4000 is used on a School On Internet Asia (SOI Asia)
project in order to carry IP traffic over ULE. However, there is an
issue with high latency jitter.
My boss, Husni, identified the problem and provided a patch for it.
The default buffer size of 32 TS frames on cx88 causes the high latency,
so our deployment changes that to 6 TS frames. This patch made the
buffer size tunable, while keeping the default buffer size of 32 TS
frames unchanged.
Signed-off-by: Achmad Husni Thamrin <husni@ai3.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original code compared "saddr_len" with zero twice in a nonsensical
way. I asked the list, and Andy Walls and Sri Deevi say that the second
check should be if "saddr_len == 1".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Srinivasa Deevi <Srinivasa.deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_QUERYSTD and VIDIOC_G_STD ioctls are currently not
supported in the FSL VIU driver. The decoder subdevice
driver saa7115 extended by previous patch supports QUERYSTD
for saa711x, so we add the appropriate ioctls to the VIU
driver to be able to determine the video input's standard.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Autodetect input's standard using field frequency detection
feature (FIDT in status byte at 0x1F) of the chips saa7111/
saa7111a/saa7113/saa7114/saa7118.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These devices do not return the full command+address, so set
scanmask accordingly.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dabusb driver were conceived as an experimental driver for a test
device. The driver never supported any shipped product, and, while
there were some updates on it in 2003, for an ancient product,
those changes were never submitted upstream.
Also, there's no DocBook for its API, nor any upstream discussion.
So, better to remove it, on .39. If later needed, we may rescue it
from git logs. For now, let's move it to staging.
Acked-by: Deti Fliegl <deti@fliegl.de>
Cc: Deti Fliegl <deti@fliegl.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/rc/streamzap.c: In function ‘streamzap_probe’:
drivers/media/rc/streamzap.c:460:2: warning: statement with no effect
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_update_signal_strength.clone.0’:
drivers/media/dvb/frontends/af9013.c:967:6: warning: ‘ret’ may be used uninitialized in this function
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few typos at the driver are causing the following warnings:
drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_start_search’:
drivers/media/dvb/frontends/stv090x.c:1486:27: warning: comparison between ‘enum stv090x_search’ and ‘enum stv090x_delsys’
drivers/media/dvb/frontends/stv090x.c:1487:24: warning: comparison between ‘enum stv090x_search’ and ‘enum stv090x_delsys’
drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_optimize_track’:
drivers/media/dvb/frontends/stv090x.c:2943:2: warning: case value ‘4’ not in enumerated type ‘enum stv090x_delsys’
The first two are due to the lack of using the delsys types
STV090x_DVBS1/STV090x_DSS
instead of
STV090x_SEARCH_DVBS1/STV090x_SEARCH_DSS
The second one is due to the usage of STV090x_UNKNOWN (enum stv090x_modulation)
instead of STV090x_ERROR (enum stv090x_delsys).
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The check for status errors is now before the check for len. That's
ok. However, the error printk's for the status error prints the URB
length. This generates this error:
drivers/media/video/gspca/gspca.c: In function ‘fill_frame’:
drivers/media/video/gspca/gspca.c:305:9: warning: ‘len’ may be used uninitialized in this function
The fix is as simple as moving the len init to happen before the checks.
Cc: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes several warnings:
drivers/media/dvb/frontends/dib7000m.c: In function ‘dib7000m_set_channel’:
drivers/media/dvb/frontends/dib7000m.c:808:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
drivers/media/dvb/frontends/dib7000m.c:869:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
drivers/media/dvb/frontends/dib7000m.c: In function ‘dib7000m_tune’:
drivers/media/dvb/frontends/dib7000m.c:1023:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
drivers/media/dvb/frontends/dib7000m.c:1033:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
drivers/media/dvb/frontends/dib7000m.c:1043:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
drivers/media/dvb/frontends/dib7000p.c: In function ‘dib7000p_set_channel’:
drivers/media/dvb/frontends/dib7000p.c:720:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
drivers/media/dvb/frontends/dib7000p.c:773:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
drivers/media/dvb/frontends/dib7000p.c: In function ‘dib7000p_tune’:
drivers/media/dvb/frontends/dib7000p.c:997:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
drivers/media/dvb/frontends/dib7000p.c:1007:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
drivers/media/dvb/frontends/dib7000p.c:1017:3: warning: case value ‘255’ not in enumerated type ‘fe_transmit_mode_t’
The drivers were prepared to support 4K carriers, but as the define were added
later, they were using a "magic" value of 255.
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/radio/radio-wl1273.c: In function ‘wl1273_fm_upload_firmware_patch’:
drivers/media/radio/radio-wl1273.c:675:2: warning: ‘n’ may be used uninitialized in this function
drivers/media/radio/radio-wl1273.c:675:2: warning: ‘i’ may be used uninitialized in this function
Those vars are never initialized, and the debug message makes no sense, as it
will show just two random values.
Cc: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-core/dmxdev.c: In function ‘dvb_dmxdev_start_feed’:
drivers/media/dvb/dvb-core/dmxdev.c:583:13: warning: comparison between ‘enum dmx_ts_pes’ and ‘enum <anonymous>’
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This comment mentions a field that doesn't exist, and talks about
videodev.h that got removed. So, it doesn't make any sense to keep
it.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no sense on keeping it on 2.6.38, as nobody is using it
anymore, at the kernel tree, and installing it at the userspace
API.
As two deprecated drivers still need it, move it to their internal
directories.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no sense on keeping VIDEO_V4L1 Kconfig option just because of
two deprecated drivers moved to staging scheduled to die on 2.6.39.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If write() on a VBI device node fails due to a bad buffer pointer from
userspace, we should notify the application properly with EFAULT, per the
V4L2 API spec.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ivtv_write_vbi() is used for both VBI data that came from the
driver internally and VBI data that came from the user. However,
it did not use copy_from_user() for reading the VBI data from the
user buffers.
This change adds a new version of the function,
ivtv_write_vbi_from_user(), that uses copy_from_user() to read the VBI
data provided via user buffers.
This should resolve a sparse build warning reported by Dave Gilbert.
Reported-by: Dr. David Alan Gilbert <linux at treblig.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx18_stream struct contained a struct cx18_dvb for
every stream object, most of which were for analog capture.
Now we only allocate the cx18_dvb object for the DTV TS stream.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error messages these drivers emitted for ioremap() failures
were misleading and not helpful for users. Reworded those messages
to help the user take action to resolve vmalloc address space
exhaustion.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The se401 driver is deprecated and is moved to staging. If no one will
convert this driver to V4L2, then it will be removed in 2.6.39.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move usbvideo to staging and mark it deprecated.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove ibmcam, konicawc and ultracam drivers. There are replaced by
gspca drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All the functionality is now handled through V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When an error is set for an isochronous packet, the length of the packet
may be null. In this case, the error was not detected and the image
was not discarded as it should be.
Reported-by: Franck Bourdonnec <fbourdonnec@chez.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These are OmniVision's OV7660 and OV9630.
Don't register the webcam when they are found.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the Vendor:Product number of the Lego Bionicle camera to
the existing gspca/sq905c.c and also a line for the camera in gspca.txt.
The camera works "out of the box" with these small changes. So this is
just in time for Christmas. Think of the children.
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove BKL ioctl and use unlocked_ioctl with core-assisted locking instead.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a copy and paste error. It should be using sizeof(cap->driver)
instead of sizeof(cap->card).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Richard Rojförs <richard.rojfors@pelagicore.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
release_firmware() just does nothing if passed a NULL pointer. So there's
no reason to test before the call in
saa7164-fw.c::saa7164_downloadfirmware().
Removing the pointless conditional also saves a few bytes.
before:
text data bss dec hex filename
7943 112 2144 10199 27d7 drivers/media/video/saa7164/saa7164-fw.o
after:
text data bss dec hex filename
7931 112 2136 10179 27c3 drivers/media/video/saa7164/saa7164-fw.o
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds USB PIDs for the Elgato EyeTV Sat device.
This device is a clone of the Terratec S7.
Signed-off-by: Sam Doshi <sam@metal-fish.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Streaming using mmap didn't work in the VIU driver. We need to
start/stop DMA in streamon/streamoff and free the buffers on
release. Add appropriate driver extension now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
zr->frame_num is a counter and && was intended here instead of &.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'n' may be bigger than MAX_INT*sizeof(int), if so checking of truncated
(int)(n/sizeof(int)) for LIRCBUF_SIZE overflow and then using nontruncated 'count'
doesn't make sense. Also n may be up to sizeof(int)-1 bytes bigger than expected,
so check value of (n % sizeof(int)) too.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This module implements V4L2 controls for the Texas Instruments
WL1273 FM Radio and handles the communication with the chip.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>