The Inventra DMA engine used with the MUSB controller in many
SoCs cannot use DMA for control transfers on EP0, but can use
DMA for all other transfers.
The USB core maps urbs for DMA if hcd->self.uses_dma is true.
(hcd->self.uses_dma is true for MUSB as well).
Split the uses_dma flag into two - one that says if the
controller needs to use PIO for control transfers, and
another which says if the controller uses DMA (for all
other transfers).
Also, populate this flag for all MUSB by default.
(Tested on OMAP3 and OMAP4 boards, with EHCI and MUSB HCDs
simultaneously in use).
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since clock support is optional across processors, don't make the whole
musb pm paths depend upon it. Just conditionalize the clock accesses.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some actions like musb_platform_exit are only performed on module
removal and not on shutdown, which results in PHY being left enabled
on reboot at least. This is sometimes causing strange failures after
reboot (observed on OMAP3 pandora board), when DEVCTL does not report
VBUS state correctly due to unknown reasons (possibly because of
communication issues between musb IP and PHY). Running
musb_platform_exit before reset seems to resolve that issue.
Move some exit code from musb_remove() to musb_shutdown() so that it
is performed on both module removal and shutdown/reset. Also convert
the host check so that it doesn't need #ifdef.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AM35x supports only 32bit read operations so we need to have
workaround for 8bit and 16bit read operations.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit 461972d8a4 (musb_core: don't call
musb_platform_exit() twice), unloading the driver module results in a WARNING
"kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being
called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode.
There exists dubious and unbalanced put_device() call in musb_free() which
takes place only in the OTG mode. As this commit caused musb_platform_exit()
to be called (and so unregister the NOP transceiver) before this put_device()
call, this function references already freed memory.
On the other hand, all the glue layers miss the otg_put_transceiver() call,
complementary to the otg_get_transceiver() call that they do. So, I think
the solution is to get rid of the strange put_device() call, and instead
call otg_put_transceiver() in the glue layers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will ignore any SESSREQ interrupt if musb is B state.
Charger detection may cause spurious SESSREQ interrupts.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since not all platforms are using the same offset 0x10 in
musb_save/restore_context() eg Blackfin the offset is 0x40,
Change the indexed address to direct.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new ulpi code defines fallback stubs for the Blackfin arch, but does
so incorrectly leading to a build failure:
drivers/usb/musb/musb_core.c:227: error: 'musb_ulpi_read' undeclared here (not in a function)
drivers/usb/musb/musb_core.c:228: error: 'musb_ulpi_write' undeclared here (not in a function)
Tweak the fallback stubs so that they do work as intended.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 1c25fda4a0 (usb: musb: handle irqs in the
order dictated by programming guide) forgot to get rid of the old 'STAGE0_MASK'
filter for calling musb_stage0_irq(), so now disconnect and suspend interrupts
are effectively ignored...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As a part of aligning the ISR code for MUSB with the specs, the
ISR code was re-written.
See Commit 1c25fda4a0 (usb: musb: handle
irqs in the order dictated by programming guide)
With this the suspend interrupt came accidently under CONFIG_USB_MUSB_HDRC_HCD.
The fix brings suspend interrupt handling outside
CONFIG_USB_MUSB_HDRC_HCD.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds helper functions for ULPI access, and implements
otg_io_access_ops for musb.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when we fail to probe(), we can call musb_exit_debugfs().
Allow that by removing section annotations.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
for now only a simple register dump entry (which can
be rather useful on debugging) and a way to start
test modes.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Program the OTG_INTERFSEL register based on
transcevier type passed from board file.
Adapt signature of musb_platform_init() function
for davinci, blackfin and tusb6010.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
boards might want to optimize their fifo configuration
to the particular needs of that specific board. Allow
that by moving all related data structures to
<linux/usb/musb.h>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1349b) clears up the confusion in many USB host
controller drivers between port features and port statuses. In mosty
cases it's true that the status bit is in the position given by the
corresponding feature value, but that's not always true and it's not
guaranteed in the USB spec.
There's no functional change, just replacing expressions of the form
(1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function forgets to call usb_remove_hcd() or musb_gadget_cleanup() iff
sysfs_create_group() fails.
[ felipe.balbi@nokia.com : review the entire error path
not only when we fail hcd or gadget ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
musb_platform_exit() is called twice from musb_init_controller() iff controller
initialization fails. Move the call (and the DevCtl register writes surrounding
it) from musb_free() to musb_remove().
Fix mispalced and now incorrect 'goto's in musb_init_controller().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resetting 'musb->clock' to NULL in musb_shutdown() prevents musb_platform_exit()
from properly disabling the clock when unloading the driver -- don't do it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate/unbalanced calls to clk_disable()/clk_put() in musb_free():
- clk_disable() is called by musb_platform_exit() just prior to this call;
- clk_put() is called by the callers of musb_free() prior to calling it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and avoid a compilation if we disable host side
of musb.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY.
However, it has no ULPI support - so there are no registers at all.
That means accesses to ULPI_BUSCONTROL have to be abstracted away
like other MUSB registers.
This fixes building for Blackfin parts again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits)
USB: backlight, appledisplay: fix incomplete registration failure handling
USB: pl2303: remove unnecessary reset of usb_device in urbs
USB: ftdi_sio: remove obsolete check in unthrottle
USB: ftdi_sio: remove unused tx_bytes counter
USB: qcaux: driver for auxiliary serial ports on Qualcomm devices
USB: pl2303: initial TIOCGSERIAL support
USB: option: add Longcheer/Longsung vendor ID
USB: fix I2C API usage in ohci-pnx4008.
USB: usbmon: mask seconds properly in text API
USB: sisusbvga: no unnecessary GFP_ATOMIC
USB: storage: onetouch: unnecessary GFP_ATOMIC
USB: serial: ftdi: add CONTEC vendor and product id
USB: remove references to port->port.count from the serial drivers
USB: tty: Prune uses of tty_request_room in the USB layer
USB: tty: Add a function to insert a string of characters with the same flag
USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()
USB: tty: kill request_room for USB ACM class
USB: tty: sort out the request_room handling for whiteheat
USB: storage: fix misplaced parenthesis
USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers
...
we were printing the info about musb probe too early where
it was still possible for things to go wrong. Move the
down right before the return 0 statement. While at that
also convert pr_info to dev_info.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
when probe() fails, we should iounmap() the mapped address.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and even added a flag to struct musb, so let's
use that.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
we have those addresses already ioremaped, so let's
use our __raw_readl/writel wrappers.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding support for MUSB register save and restore during system
suspend and resume.
Changes:
- Added musb_save/restore_context() functions
- Added platform specific musb_platform_save/restore_context()
to handle platform specific jobs.
- Maintaining BlackFin compatibility by adding read/write
functions for registers which are not available in BlackFin
Tested system suspend and resume on OMAP3EVM board.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the board might use external Vbus power supply on musb
interface which would require to program ULPI_BUSCONTROL register.
Adding 'extvbus' flag which can be set from such boards which will
be checked at musb driver files before programming ULPI_BUSCONTROL.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Save dynamic FIFO read only information for later uses during
musb_save/restore_context functions.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB's programming guide dictates how we should handle its
irqs and in which order. Follow that.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have observed MSC data read corruption when USB LAN device is
also connected and it's interface is up.
Silicon team has confirmed an errata where in all the active
transfers should use FIFO space either in first 8K or next 8K.
So far we have observed the issue in above use case scenario.
As a workaround to it, adding a new FIFO config (5) fitting well
within first 8K which can be used for such use cases.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it's easier to keep up and add more sysfs entries
as necessary.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below array index out of bounds issue.
Buffer overflow, array index of 'aInfo' may be out of
bounds. Array 'aInfo' of size 78 may use index value(s) 6..84
The data stored in 'aInfo' array exceeds the array size of 78.
This patch increases the size of this array to hold the string
correctly without any memory corruption.
This issue was reported by Klockwork tool.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On OTG and gadget-only configurations, we need a gadget driver
in order to work properly, so avoid changing operation modes
when there's no gadget driver loaded.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
probe() already was on __init, so moving remove() to __exit.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB: save hardware revision at init
This can be used later to flag workarounds for issues affecting
particular revisions. Saving this at init avoids having to
read the HWVERS register multiple times in code.
While at it, use macros to extract the version information
instead of using hardcoded values.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Invoke put_device(musb->xceiv->dev) before musb_platform_exit()as
xceiv is getting unregistered in musb_platform_exit().
Fixes put_device() panic when module insert/removal is performed
multiple times.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Anand Gadiyar