Change PnP resource handling code to use proper type for resource start and
length. Fixes bogus regions reported in /proc/iomem.
I've also made some pointer constant, as they are constant...
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix an off-by-one spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch addresses the following issues with the pxa2xx FIr driver:
1. increment overrun error counter and not frame error counter on ICSR1_ROR bit set in ICSR1.
2. drop frames reported with the frame error from the IC.
3. when resetting the receiver and preparing it for the next DMA in pxa_irda_fir_irq() actually clear the Rx FIFO. See description in Table 11-2 in PXA270 Developer's Manual of the RXE bit.
Correction added in version 2: clearing the IC Rx FIFO also has to be done in pxa_irda_fir_dma_tx_irq()
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ingo reported that built-in drivers suffered bootup hangs with certain
driver unregistry sequences, due to sysfs breakage.
Do the minimal fix for v2.6.21: only wait if the driver is a module.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've seen this several times on this drive, completely reproducible.
Once it has hung, power needs to be cut from the drive to recover it, a
simple reboot is not enough. So I'd suggest disabling NCQ on this
drive.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
NetXen: Fix hardware access for ppc architecture.
sis190: new PHY support
atl1: save mac address on remove
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark some static arrays as const that aren't and shouldn't be modified, and
remove incorrect static attribute from some variables.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported to work on the WinFast 761GXK8MB-RS motherboard.
Plain 10/100 Mbps.
Signed-off-by: Paul Gibbons <paul@pkami.e7even.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some atl1 boards get their MAC address written directly to the register
by the BIOS during POST, rather than storing it in EEPROM that's
accessible to the driver. If the MAC register on one of these boards
is changed and then the module is unloaded, the permanent MAC address
will be forgotten until the box is rebooted. We should save the
permanent address during removal if we've been messing with it.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bnx2_has_work()'s logic is flawed and can cause the driver to miss
a link event. The fix is to compare the status block's attn_bits
and attn_bits_ack to determine if there is a link event.
Update version to 1.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Handle aborting a command after it is sent
IB/mthca: Fix thinko in init_mr_table()
RDMA/cxgb3: Fix resource leak in cxio_hal_init_ctrl_qp()
nmi_cpu_setup() is called from hardirq context and acquires oprofilefs_lock.
alloc_event_buffer() and oprofilefs_ulong_from_user() acquire this lock
without disabling irqs, which could deadlock.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: NCQ is broken on Maxtor 6L250S0
pata_pdc202xx_old: LBA48 bug
libata: IDENTIFY backwards for drive side cable detection
ahci.c: walkaround for SB600 SATA internal error issue
[libata] Disable ACPI by default; fix namespace problems
Fix section mismatch warning by moving data into __devinitdata section.
Add __devinit to initialization functions.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checking for allocated DVMA memory and granted IRQ line.
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In this driver, the default ethernet address is first set by by calling
eth_port_uc_addr_get() which reads the relevant registers of the
corresponding port as initially set by firmware. However that function
used the port_num field accessed through the private area of net_dev
before it was set.
The result was that one board I have ended up with the unicast address
set to 00:00:00:00:00:00 (only port 1 is connected on this board). The
problem appeared after commit 84dd619e4d.
This patch fixes the bug by setting mp->port_num prior to calling
eth_port_uc_get_addr().
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The tx timeout routine was waking the tx queue conditionally. However,
it must call it unconditionally since the dev_watchdog has halted the tx
queue before calling the timeout function.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The nic poll routine was missing the call to the optimized irq routine.
This patch adds the missing call for the optimized path.
See http://bugzilla.kernel.org/show_bug.cgi?id=7950 for more information.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed rx checksum bits. Turn on TCP processing for rx checksum.
Fixed max frame length register write. It wasn't getting set
in multi-port system. Set rx buffer queue length properly
for jumbo frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the rx queue pointer when exiting NAPI poll rather than
at the end of each iteration. Remove unnecessary PCI flushes
that occurred after every write. Now write all regs and
flush once.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This was removed in a previous patch to increase performance, but
caused a transmit error for the 4032 chip.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original vendor driver contained a private ether_crc_le() function
that produced an inverted crc. When we changed to the kernel version of
ether_crc_le(), we neglected to undo the inversion. Let's do it now.
Discovered by and patch proffered by Jose Alberto Reguero.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correctly detect when TSO should be used on transmit by looking at the
skb->gso_size rather than seeing if the frame was larger than our MTU.
The old method causes problems when a host with a large (jumbo) MTU is
sending to a host with a small (standard) MTU.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With this applied, my machine has stopped all those painful messages.
dmesg now says :
root@riri:/Kernels# dmesg | grep LBA
ata1.00: 490234752 sectors, multi 0: LBA48 NCQ (not used)
ata2.00: 640 sectors, multi 1: LBA
ata3.00: 490234752 sectors, multi 0: LBA48 NCQ (not used)
Signed-off-by: Paul Rolland <rol@as2917.net>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In LBA48 mode we have to help the controller to get anything to work. The
chip provides a register giving word counts meant for ATAPI use which we
can use. However we need to load the count in words not bytes..
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For drive side cable detection to work correctly, drives need to be
identified backwards such that the slave device releases PDIAG- before
the mater drive tries to detect cable type. ata_bus_probe() was fixed
by commit f31f0cc2f0 but the new EH path
wasn't fixed. This patch makes new EH path do IDENTIFY backwards.
ata_dev_configure() for new devices are still performed master first.
This is to keep the detection messages in forward order.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is a HW issue in ATI SB600 SATA that PxSERR.E should not be
set on some conditions, for example, when there is no media in SATA
CD/DVD drive or media is not ready, AHCI controller fails to execute
ATAPI commands and reports PORT_IRQ_TF_ERR, but ATI SB600 SATA
controller sets PxSERR.E at the
same time, which is not necessary.
This patch is just to ignore the INTERNAL ERROR in such case.
Without this patch, ahci error handler will report many errors as
below:
----------- cut from dmesg -----------
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x0 data 0
res 51/24:03:00:00:20/00:00:00:00:00/a0 Emask 0x40 (internal error)
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error)
-------- end cut ---------
Signed-off-by: Conke Hu <conke.hu@amd.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not yet ready to turn on ATA ACPI by default, for either PATA or SATA.
Also, rename the global-scope module parameter variable 'noacpi' to
something more libata-specific, reducing the potential for namespace
collision.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent changes in the specs that were introduced in commit
740ac4fb08 were incorrect and resulted in machine check
errors on the PPC architecture for G PHY's with a revision number equal to 1. The
two offending changes are reverted.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a duplicated leftshift in bcm43xx_radio_set_tx_iq. data_high values are
already leftshifted. Thanks to Michael Buesch for spotting this.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places where the PHY version and revision were interchanged.
These are changed in the specifications on 2/13/07 and now use "analog" instead
instead of "version" to help reduce confusion.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://kvm.qumranet.com/home/avi/kvm:
KVM: always reload segment selectors
KVM: Prevent system selectors leaking into guest on real->protected mode transition on vmx
I2O subsystem has been broken in mainstream several months ago (after
2.6.18). Commit 4aff5e2333 from Jens
Axboe split struct request ->flags into two parts: cmd_type and
cmd_flags.
In i2o layer this patch has replaced flag REQ_SPECIAL by the according
cmd_type. However i2o has used REQ_SPECIAL not as command type but as
driver-specific flag for the debug purposes. As result all i2o requests
have type "special" now, are not processed to the hardware and fail with
I/O error:
i2o/hda:<3>Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
unable to read partition table
block-osm: device added (TID: 207): i2o/hda
The following patch removes the extra debug checks without any drawbacks and
restores the normal driver's work.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:eisa_root_register from .text between 'pci_eisa_init' (at offset 0xabf670) and 'virtual_eisa_release'
AFAIK a PCI to EISA bridge isn't anything hotpluggable, so
pci_eisa_init() can become __init.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_register_master from .text between 'spi_bitbang_start' (at offset 0x84e11a) and 'bitbang_work'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_alloc_master from .text between 'butterfly_attach' (at offset 0x84e681) and 'at25_remove'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_new_device from .text between 'butterfly_attach' (at offset 0x84e7e4) and 'at25_remove'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Bob's machine clocksource is selecting PIT over the ACPI PM timer,
because he has the PIIX4 bug. That bug drops the ACPI PM timers rating
to the same as the PIT, so that's why you're getting the PIT.
Realistically, the PIT is much slower then even the triple read ACPI PM,
so the de-ranking code is probably dropping it too far.
So don't drop ACPI PM quite so low if we see the PIIX4 bug.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Bob Tracy <rct@gherkin.frus.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Petr Vandrovec