Use netdev_alloc_skb. This sets skb->dev and allows arch specific
allocation.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use netdev_alloc_skb for rx buffer allocation. This sets skb->dev
and can be overriden for NUMA machines.
This device is PowerPC only, so not tested or compiled.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Turn on special bits to save more power when device is shutdown.
Tested on a limited range of hardware, some of the bits are for hardware
that probably isn't even in production (like Yukon Supreme) and was ported
from the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Put PHY int sleep mode (from vendor sk98lin 10.50 driver) when the
network device is brought down.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Later changes add more code to PHY power changes so refactor now.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Match the suspend/resume code ordering in e100/e1000e more closely.
For example the configuration space should be saved on suspend even for
devices that are not up.
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The memory mapped device configuration space is lost during hibernate.
Save and restore it (fixes 'swapped mac' problem).
Signed-off-by: TTobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When hibernating in 'shutdown' mode, after saving the image the suspend hook
is not called again.
However, if the device is in promiscous mode, wake-on-lan will not work.
This adds a shutdown hook to setup wake-on-lan before the final shutdown.
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Port the fs_enet driver to support the MDIO on GPIO driver for PHY access
in addition to the mii-bitbang driver.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds an MDIO bitbang driver that uses the GPIO library and its
OF bindings to access the bus I/Os.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove our own implementation of I2C bit-banging.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
cxgb3 uses lro_* functions and selects INET_LRO, but this doesn't help unless
INET is already enabled, so make the driver depend on INET also.
sge.c:(.text+0x9f09a): undefined reference to `lro_flush_all'
sge.c:(.text+0x9f62f): undefined reference to `lro_receive_skb'
sge.c:(.text+0x9f8a3): undefined reference to `lro_receive_frags'
sge.c:(.text+0x9fbe0): undefined reference to `lro_vlan_hwaccel_receive_skb'
sge.c:(.text+0x9ffcd): undefined reference to `lro_vlan_hwaccel_receive_frags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make driver more readable on standard 80 col windows.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Handle shared IRQ correctly. If IRQ is shared, it typically will show up
as an IRQ with an empty status field. So check in driver and handle it
without crapping out with invalid interrupt message.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rx allocation failure at runtime is non-fatal. For normal Rx frame, it
just reuses the buffer, and during setup it just continues with a smaller
receive buffer pool.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make this driver compile cleanly on 64 bit platforms.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use new netdevice common stats area.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use skb_padto to pad frames, this avoid allocation of separate buffer just
for dma of the extra bytes.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add multi-slice/MSI-X support. By default, a single slice
(and the normal firmware) are used. To enable msi-x, multi-slice
mode, one must load the driver with myri10ge_max_slices set to
either -1, or something larger than 1.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add several routines that multislices support will use.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following patch is seems to fix the tulip suspend/resume panic:
http://bugzilla.kernel.org/show_bug.cgi?id=8952#c46
My attempts at a cleaner patch failed and Pavel thinks this is OK.
Original from: kernelbugs@tap.homeip.net
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When using 4+ GB RAM and SWIOTLB is active, the driver corrupts
memory by writing an skb after the relevant DMA page has been
unmapped. Although this doesn't happen when *not* using bounce
buffers, clearing the pointer to the DMA page after unmapping
it fixes the problem.
http://marc.info/?t=120861317000005&r=2&w=2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Because we cache the last failed-to-xmit packet, if there are no
packets queued behind that one we may never send it (reproduced here
as TCP stalls, "cured" by an outgoing ping).
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If we fail to transmit a packet, we assume the queue is full and put
the skb into last_xmit_skb. However, if more space frees up before we
xmit it, we loop, and the result can be transmitting the same skb twice.
Fix is simple: set skb to NULL if we've used it in some way, and check
before sending.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 5a0a92e67b mentions len < ETH_ZLEN
is true for ARP packets. This obviously is not unlikely.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After request_dma() succeeding, any error path should do free_dma().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is normal when the external link is down so don't report it as an error.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch silences the build warnings concerning o2net_init_nst()
and friends when building without CONFIG_DEBUG_FS enabled.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
This patch silences the build warnings concerning dlm_debug_init()
and friends when building without CONFIG_DEBUG_FS enabled.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
This patch silences the build warnings concerning o2net_debugfs_init()
and friends when building without CONFIG_DEBUG_FS enabled.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
The static structure describing the userspace cluster plugin for ocfs2
was named 'user_stack', which is a real pain when people are grep(1)ing
the tree for the program stack object 'user_stack'. Change the name to
something distinct and namespaced.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: notify on empty
virtio: force callback on empty.
virtio_blk: fix endianess annotations
virtio_config: fix len calculation of config elements
virtio_net: another race with virtio_net and enable_cb
virtio: An entropy device, as suggested by hpa.
virtio_blk: allow read-only disks
lguest: fix ugly <NULL> in /proc/interrupts
virtio: set device index in common code.
virtio: virtio_pci should not set bus_id.
virtio: bus_id for devices should contain 'virtio'
Fix crash in virtio_blk during modprobe ; rmmod ; modprobe
lguest: use ioremap_cache, not ioremap
* Wim Van Sebroeck <wim@iguana.be> wrote:
> Author: Jordan Crouse <jordan.crouse@amd.com>
> Date: Mon Jan 21 10:07:00 2008 -0700
>
> [WATCHDOG] Add a watchdog driver based on the CS5535/CS5536 MFGPT timers
-tip testing found the following build failure on latest -git:
drivers/watchdog/geodewdt.c: In function 'geodewdt_probe':
drivers/watchdog/geodewdt.c:225: error: too many arguments to function 'geode_mfgpt_alloc_timer'
make[1]: *** [drivers/watchdog/geodewdt.o] Error 1
make: *** [drivers/watchdog/geodewdt.o] Error 2
with this config:
http://redhat.com/~mingo/misc/config-Fri_May_30_15_19_52_CEST_2008.bad
find the fix below.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When Greg "fixed" the sysfs usage of that driver a while back, he seem
to have introduced a bug where the quotes are added around the name of
our specific sysfs files, thus breaking the user space tool.
This fixes it. Tested DLPAR operations on a POWER6 machine successfully.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c,
as the actual PCI IDs deployed in the field differed from the forecasted ones
preemptively placed in the driver.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following commit (4c9bf4e799):
libata: replace tf_read with qc_fill_rtf for non-SFF drivers
Broke the sata_fsl.c driver in 2.6.26-rc. I know the following patch fixes
the issue, it clearly also adds port multipler support. The current
2.6.26-rc driver is broken.
On boot with debug enabled we get something like (w/o this patch):
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
.. continues for ever.
This change fixes this as a side effect of adding port multiplier support.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
