When chasing a performance issue on ppc64, I noticed tasks
communicating via a pipe would often end up on different nodes.
It turns out SD_WAKE_AFFINE is not set in our node defition. Commit
9fcd18c9e6 (sched: re-tune balancing) enabled SD_WAKE_AFFINE
in the node definition for x86 and we need a similar change for
ppc64.
I used lmbench lat_ctx and perf bench pipe to verify this fix. Each
benchmark was run 10 times and the average taken.
lmbench lat_ctx:
before: 66565 ops/sec
after: 204700 ops/sec
3.1x faster
perf bench pipe:
before: 5.6570 usecs
after: 1.3470 usecs
4.2x faster
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a new udbg driver for the PS3 gelic Ehthernet device.
This driver shares only a few stucture and constant definitions with the
gelic Ethernet device driver, so is implemented as a stand-alone driver
with no dependencies on the gelic Ethernet device driver.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since commit 188917e183, /proc/ppc64 is a
symlink to /proc/powerpc/. That means that creating /proc/ppc64/eeh will
end up with a unaccessible file, that is not listed under /proc/powerpc/
and, then, not listed under /proc/ppc64/.
Creating /proc/powerpc/eeh fixes that problem and maintain the
compatibility intended with the ppc64 symlink.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org> [3.x]
This should fix the following warning:
LD arch/powerpc/sysdev/xics/built-in.o
WARNING: arch/powerpc/sysdev/xics/built-in.o(.text+0x1310): Section mismatch in
reference from the function .icp_native_init() to the function
.init.text:.icp_native_init_one_node()
The function .icp_native_init() references
the function __init .icp_native_init_one_node().
This is often because .icp_native_init lacks a __init
annotation or the annotation of .icp_native_init_one_node is wrong.
icp_native_init() is only referenced in `arch/powerpc/sysdev/xics/xics-common.c'
by xics_init() which is itself marked with __init.
= not built-tested =
Reported-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
During hotplug CPU add we get the following error:
Unexpected Error (0) returned from configure-connector
ibm,configure-connector returns 0 for configuration complete, so
catch this and avoid the error.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>
In SMP mode, the kernel would produce call trace when resumed
from hibernation. The reason is when the function destroy_context
is called to drop the resuming mm context, the mm->context.active
is 1 which is wrong and should be zero.
We pass the current->active_mm as previous mm context to function
switch_mmu_context to decrease the context.active by 1.
In UP mode, there is no effect.
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The various port_init_hw methods of ppc4xx_pciex_hwops should have been
marked __init and when I added ppc4xx_pciex_port_reset_sdr(), which is
__init. This added many section mismatch warnings like:
WARNING: arch/powerpc/sysdev/built-in.o(.text+0x5c68): Section mismatch in reference from the function ppc440spe_pciex_init_port_hw() to the function .init.text:ppc4xx_pciex_port_reset_sdr()
The function ppc440spe_pciex_init_port_hw() references
the function __init ppc4xx_pciex_port_reset_sdr().
This is often because ppc440spe_pciex_init_port_hw lacks a __init
annotation or the annotation of ppc4xx_pciex_port_reset_sdr is wrong.
Trivial patch to silence those warnings.
Reported-By: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Yours Tony
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch by Michael Ellerman <michael@ellerman.id.au>
Patch was simply forward ported upstream.
Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch by Benjamin Herrenschmidt <benh@kernel.crashing.org>
Modernized and slightly modified to not record erros into the nvram
log since we do not have that device driver just yet.
Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some config selections were applied to the platform (reference board)
when they actuall apply to the chip.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At this point, window has not been stored anywhere, so it has to be freed
before leaving the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
u64 is used rather than phys_addr_t to keep things simple, as
this is called from assembly code.
Update callers to pass a 64-bit address in r3/r4. Other unused
register assignments that were once parameters to machine_init
are dropped.
For FSL BookE, look up the physical address of the device tree from the
effective address passed in r3 by the loader. This is required for
situations where memory does not start at zero (due to AMP or IOMMU-less
virtualization), and thus the IMA doesn't start at zero, and thus the
device tree effective address does not equal the physical address.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Capture more than twice as much text from the printk buffer, and
compress it to fit it in the lnx,oops-log NVRAM partition. You
can view the compressed text using the new (as of July 20) --unzip
option of the nvram command in the powerpc-utils package.
[BenH: Added select of ZLIB_DEFLATE]
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the build can (very rarely) fail to build because libfdt.h has
not been created or is in the process of being copied.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is one place in the MPIC driver that assumes that the cores are numbered
from 0 to n-1. However, this is not true if the CPUs are not numbered
sequentially. This can happen on a eight-core SOC where cores two and three
are removed in the device tree. So instead of blindly looping, we iterate
over the discovered CPUs and use the SMP ID as the index.
This means that we no longer ask the MPIC how many CPUs there are, so
we also delete mpic->num_cpus.
We also catch if the number of CPUs in the SOC exceeds the number that the
MPIC supports. This should never happen, of course, but it's good to be
sure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable hugepages on Freescale BookE processors. This allows the kernel to
use huge TLB entries to map pages, which can greatly reduce the number of
TLB misses and the amount of TLB thrashing experienced by applications with
large memory footprints. Care should be taken when using this on FSL
processors, as the number of large TLB entries supported by the core is low
(16-64) on current processors.
The supported set of hugepage sizes include 4m, 16m, 64m, 256m, and 1g.
Page sizes larger than the max zone size are called "gigantic" pages and
must be allocated on the command line (and cannot be deallocated).
This is currently only fully implemented for Freescale 32-bit BookE
processors, but there is some infrastructure in the code for
64-bit BooKE.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This iotype is only used by the legacy_serial code in powerpc, so the
code should live there, rather than be compiled in for every 8250
driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-serial@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new get_required_mask hook name is longer than many of but not all
of the prior ops. Tidy the struct initializers to align the equal signs
using the local whitespace.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that the generic code has dma_map_ops set, instead of having a
messy ifdef & if block in the base dma_get_required_mask hook push
the computation into the dma ops.
If the ops fails to set the get_required_mask hook default to the
width of dma_addr_t.
This also corrects ibmbus ibmebus_dma_supported to require a 64
bit mask. I doubt anything is checking or setting the dma mask on
that bus.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The hook dma_get_required_mask is supposed to return the mask required
by the platform to operate efficently. The generic version of
dma_get_required_mask in driver/base/platform.c returns a mask based
only on max_pfn. However, this is likely too big for iommu systems
and could be too small for platforms that require a dma offset or have
a secondary window at a high offset.
Override the default, provide a hook in ppc_md used by pseries lpar and
cell, and provide the default answer based on memblock_end_of_DRAM(),
with hooks for get_dma_offset, and provide an implementation for iommu
that looks at the defined table size. Coverting from the end address
to the required bit mask is based on the generic implementation.
The need for this was discovered when the qla2xxx driver switched to
64 bit dma then reverted to 32 bit when dma_get_required_mask said
32 bits was sufficient.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/p1023rds: Fix the error of bank-width of nor flash
powerpc/85xx: enable caam crypto driver by default
powerpc/85xx: enable the audio drivers in the defconfigs
In the p1023rds, a physical bus of nor flash is 16 bits width.
The bank-width is width (in bytes) of the bus width. So, the
value of bank-width of nor flash is not one, and it should be
two.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
corenet based SoCs have SEC4 h/w, so enable the SEC4 driver,
caam, and the algorithms it supports, and disable the
SEC2/3 driver, talitos.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable the audio drivers in the non-corenet 85xx defconfigs so that audio
is enabled on the Freescale P1022DS reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These were missed in commit f5b9409973 "All Arch: remove linkage
for sys_nfsservctl system call" due to them having no sys_ prefix
(presumably).
Cc: NeilBrown <neilb@suse.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug causes the IECSR register clear failure. In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared. So the related ISR may be called persistently.
The RETE bit in IECSR is cleared by writing a 1 to it.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds a register to the config space for the 460sx. Changes the vc0
detect to a pll detect. maps configuration space to test the link
status. changes the setup to enable gen2 devices to operate at gen2
speeds. fixes mapping that was not correct for the 460sx. added
bit definitions for the OMRxMSKL registers. Removed reserved bit
that was set incorrectly in the OMR2MSKL register.
tested on the 460sx eiger and custom board
Signed-off-by: Ayman El-Khashab <ayman@elkhashab.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
This patch adds kexec support for PPC440 based chipsets. This work is based
on the KEXEC patches for FSL BookE.
The FSL BookE patch and the code flow could be found at the link below:
http://patchwork.ozlabs.org/patch/49359/
Steps:
1) Invalidate all the TLB entries except the one this code is run from
2) Create a tmp mapping for our code in the other address space and jump to it
3) Invalidate the entry we used
4) Create a 1:1 mapping for 0-2GiB in blocks of 256M
5) Jump to the new 1:1 mapping and invalidate the tmp mapping
I have tested this patches on Ebony, Sequoia boards and Virtex on QEMU.
You need kexec-tools commit e8b7939b1e or newer for ppc440x support,
available at:
git://git.kernel.org/pub/scm/utils/kernel/kexec/kexec-tools.git
Signed-off-by: Suzuki Poulose <suzuki@in.ibm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Brown paper bag day, previous commit wouldn't work very well with modules
enabled. Move the exports into the ifdef.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit fea80311a9
"iomap: make IOPORT/PCI mapping functions conditional"
Broke powerpc build without CONFIG_PCI as we would still define
pci_iomap(), which overlaps with the new empty inline in the headers.
Make our implementation conditional on CONFIG_PCI
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 112d1fe9f7
"powerpc/4xx: Add check_link to struct ppc4xx_pciex_hwops" inadvertently
broke 405 builds due to some functions being over protected by an
ifdef CONFIG_44x.
Move them back out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The VPA, SLB shadow and DTL degistration functions do not need an
address, so simplify things and remove it.
Also cleanup pseries_kexec_cpu_down a bit by storing the cpu IDs
in local variables.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make the VPA, SLB shadow and DTL registration and deregistration
functions print consistent messages on error. I needed the firmware
error code while chasing a kexec bug but we weren't printing it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Recent versions of firmware will fail to unmap the virtual processor
area if we have a dispatch trace log registered. This causes kexec
to fail.
If a trace log is registered this patch unregisters it before the
SLB shadow and virtual processor areas, fixing the problem.
The address argument is ignored by firmware on unregister so we
may as well remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
KVM_GUEST adds a 1 MB array to the kernel (kvm_tmp) which grew
my kernel enough to cause it to fail to boot.
Dynamically allocating or reducing the size of this array is a
good idea, but in the meantime I think it makes sense to make
KVM_GUEST default to n in order to minimise surprises.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On a box with gcc 4.3.2, I see errors like:
arch/powerpc/kvm/book3s_hv_rmhandlers.S:1254: Error: Unrecognized opcode: stxvd2x
arch/powerpc/kvm/book3s_hv_rmhandlers.S:1316: Error: Unrecognized opcode: lxvd2x
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The ibm,io-events code is a bit verbose with its error messages.
Reverse the reporting so we only print when we successfully enable
I/O event interrupts.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing boot failures on some very large boxes even with
commit b5416ca9f8 (powerpc: Move kdump default base address to
64MB on 64bit).
This patch halves the RMO so both kernels get about the same
amount of RMO memory. On large machines this region will be
at least 256MB, so each kernel will get 128MB.
We cap it at 256MB (small SLB size) since some early allocations need
to be in the bolted SLB region. We could relax this on machines with
1TB SLBs in a future patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Panic observed on an older kernel when collecting call chains for
the context-switch software event:
[<b0180e00>]rb_erase+0x1b4/0x3e8
[<b00430f4>]__dequeue_entity+0x50/0xe8
[<b0043304>]set_next_entity+0x178/0x1bc
[<b0043440>]pick_next_task_fair+0xb0/0x118
[<b02ada80>]schedule+0x500/0x614
[<b02afaa8>]rwsem_down_failed_common+0xf0/0x264
[<b02afca0>]rwsem_down_read_failed+0x34/0x54
[<b02aed4c>]down_read+0x3c/0x54
[<b0023b58>]do_page_fault+0x114/0x5e8
[<b001e350>]handle_page_fault+0xc/0x80
[<b0022dec>]perf_callchain+0x224/0x31c
[<b009ba70>]perf_prepare_sample+0x240/0x2fc
[<b009d760>]__perf_event_overflow+0x280/0x398
[<b009d914>]perf_swevent_overflow+0x9c/0x10c
[<b009db54>]perf_swevent_ctx_event+0x1d0/0x230
[<b009dc38>]do_perf_sw_event+0x84/0xe4
[<b009dde8>]perf_sw_event_context_switch+0x150/0x1b4
[<b009de90>]perf_event_task_sched_out+0x44/0x2d4
[<b02ad840>]schedule+0x2c0/0x614
[<b0047dc0>]__cond_resched+0x34/0x90
[<b02adcc8>]_cond_resched+0x4c/0x68
[<b00bccf8>]move_page_tables+0xb0/0x418
[<b00d7ee0>]setup_arg_pages+0x184/0x2a0
[<b0110914>]load_elf_binary+0x394/0x1208
[<b00d6e28>]search_binary_handler+0xe0/0x2c4
[<b00d834c>]do_execve+0x1bc/0x268
[<b0015394>]sys_execve+0x84/0xc8
[<b001df10>]ret_from_syscall+0x0/0x3c
A page fault occurred walking the callchain while creating a perf
sample for the context-switch event. To handle the page fault the
mmap_sem is needed, but it is currently held by setup_arg_pages.
(setup_arg_pages calls shift_arg_pages with the mmap_sem held.
shift_arg_pages then calls move_page_tables which has a cond_resched
at the top of its for loop - hitting that cond_resched is what caused
the context switch.)
This is an extension of Anton's proposed patch:
https://lkml.org/lkml/2011/7/24/151
adding case for 32-bit ppc.
Tested on the system that first generated the panic and then again
with latest kernel using a PPC VM. I am not able to test the 64-bit
path - I do not have H/W for it and 64-bit PPC VMs (qemu on Intel)
is horribly slow.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
One definition of PV_POWER7 seems enough to me.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On a box with 8TB of RAM the MMU hashtable is 64GB in size. That
means we have 4G PTEs. pSeries_lpar_hptab_clear was using a signed
int to store the index which will overflow at 2G.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I hit an oops at boot on the first instruction of timer_cpu_notify:
NIP [c000000000722f88] .timer_cpu_notify+0x0/0x388
The code should look like:
c000000000722f78: eb e9 00 30 ld r31,48(r9)
c000000000722f7c: 2f bf 00 00 cmpdi cr7,r31,0
c000000000722f80: 40 9e ff 44 bne+ cr7,c000000000722ec4
c000000000722f84: 4b ff ff 74 b c000000000722ef8
c000000000722f88 <.timer_cpu_notify>:
c000000000722f88: 7c 08 02 a6 mflr r0
c000000000722f8c: 2f a4 00 07 cmpdi cr7,r4,7
c000000000722f90: fb c1 ff f0 std r30,-16(r1)
c000000000722f94: fb 61 ff d8 std r27,-40(r1)
But the oops output shows:
eb61ffd8 eb81ffe0 eba1ffe8 ebc1fff0 7c0803a6 ebe1fff8 4e800020
00000000 ebe90030 c0000000 00ad0a28 00000000 2fa40007 fbc1fff0 fb61ffd8
So we scribbled over our instructions with c000000000ad0a28, which
is an address inside the jump_table ELF section.
It turns out the jump_table section is only aligned to 8 bytes but
we are aligning our entries within the section to 16 bytes. This
means our entries are offset from the table:
c000000000acd4a8 <__start___jump_table>:
...
c000000000ad0a10: c0 00 00 00 lfs f0,0(0)
c000000000ad0a14: 00 70 cd 5c .long 0x70cd5c
c000000000ad0a18: c0 00 00 00 lfs f0,0(0)
c000000000ad0a1c: 00 70 cd 90 .long 0x70cd90
c000000000ad0a20: c0 00 00 00 lfs f0,0(0)
c000000000ad0a24: 00 ac a4 20 .long 0xaca420
And the jump table sort code gets very confused and writes into the
wrong spot. Remove the alignment, and also remove the padding since
we it saves some space and we shouldn't need it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a newline to the panic messages in make_room. Also fix a
comment that suggested our chunk size is 4Mb. It's 1MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have a box that fails in OF during boot with:
DEFAULT CATCH!, exception-handler=fff00400
at %SRR0: 49424d2c4c6f6768 %SRR1: 800000004000b002
ie "IBM,Logh". OF got corrupted with a device tree string.
Looking at make_room and alloc_up, we claim the first chunk (1 MB)
but we never claim any more. mem_end is always set to alloc_top
which is the top of our available address space, guaranteeing we will
never call alloc_up and claim more memory.
Also alloc_up wasn't setting alloc_bottom to the bottom of the
available address space.
This doesn't help the box to boot, but we at least fail with
an obvious error. We could relocate the device tree in a future
patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit af9eef3c7b caused cpu_setup to see
the_cpu_spec, rather than the source struct. However, on 32-bit, the
return value of identify_cpu was being used for feature fixups, and
identify_cpu was returning the source struct. So if cpu_setup patches
the feature bits, the update won't affect the fixups.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
