Fixed formatting (tabs and line breaks).
The TIOCGICOUNT device ioctl allows unprivileged users to read
uninitialized stack memory, because the "reserved" member of the
serial_icounter_struct struct declared on the stack in hso_get_count()
is not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an array with 1.x metadata is assembled with the last disk missing,
md doesn't properly record the fact that the disk was missing.
This is unlikely to cause a real problem as the event count will be
different to the count on the missing disk so it won't be included in
the array. However it could still cause confusion.
So make sure we clear all the relevant slots, not just the early ones.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that we depend on md_update_sb to clear variable bits in
mddev->flags (rather than trying not to set them) it is important to
always call md_update_sb when appropriate.
md_check_recovery has this job but explicitly avoids it for ->external
metadata arrays. This is not longer appropraite, or needed.
However we do want to avoid taking the mddev lock if only
MD_CHANGE_PENDING is set as that is not cleared by md_update_sb for
external-metadata arrays.
Reported-by: "Kwolek, Adam" <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
drivers/firewire/nosy* is a stand-alone driver that does not depend on
CONFIG_FIREWIRE. Hence let make descend into drivers/firewire/ also
if that option is off.
The stand-alone driver drivers/ieee1394/init_ohci1394_dma* will soon be
moved into drivers/firewire/ too and will require the same makefile fix.
Side effect:
As mentioned in https://bugzilla.novell.com/show_bug.cgi?id=586172#c24
this influences the order in which either firewire-ohci or ohci1394 is
going to be bound to an OHCI-1394 controller in case of a modular build
of both drivers if no modprobe blacklist entries are configured.
However, a user of such a setup cannot expect deterministic behavior
anyway. The Kconfig help and the migration guide at
ieee1394.wiki.kernel.org recommend blacklist entries when a dual
IEEE 1394 stack build is being used. (The coexistence period of the two
stacks is planned to end soon.)
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: Enable NXP LPC32XX support in Kconfig (resend)
watchdog: ts72xx_wdt: disable watchdog at probe
watchdog: sb_wdog: release irq and reboot notifier in error path and module_exit()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: wm8350-regulator - fix the logic of checking REGULATOR_MODE_STANDBY mode
regulator: wm831x-ldo - fix the logic to set REGULATOR_MODE_IDLE and REGULATOR_MODE_STANDBY modes
regulator: ab8500 - fix off-by-one value range checking for selector
regulator: 88pm8607 - fix value range checking for accessing info->vol_table
regulator: isl6271a-regulator - fix regulator_desc parameter for regulator_register()
regulator: ad5398 - fix a memory leak
regulator: Update e-mail address for Liam Girdwood
regulator: set max8998->dev to &pdev->dev.
regulator: tps6586x-regulator - fix bit_mask parameter for tps6586x_set_bits()
regulator: tps6586x-regulator - fix value range checking for val
regulator: max8998 - set max8998->num_regulators
regulator: max8998 - fix memory allocation size for max8998->rdev
regulator: tps6507x - remove incorrect comments
regulator: max1586 - improve the logic of choosing selector
regulator: ab8500 - fix the logic to remove already registered regulators in error path
regulator: ab3100 - fix the logic to remove already registered regulators in error path
regulator/ab8500: move dereference below the check for NULL
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: only warn on mipmap size checks in r600 cs checker (v2)
drm/radeon/kms: force legacy pll algo for RV620 LVDS
drm: fix race between driver loading and userspace open.
drm: Use a nondestructive mode for output detect when polling (v2)
drm/radeon/kms: fix the colorbuffer CS checker for r300-r500
drm/radeon/kms: increase lockup detection interval to 10 sec for r100-r500
drm/radeon/kms/evergreen: fix backend setup
drm: Use a nondestructive mode for output detect when polling
drm/radeon: add some missing copyright headers
drm: Only decouple the old_fb from the crtc is we call mode_set*
drm/radeon/kms: don't enable underscan with interlaced modes
drm/radeon/kms: add connector table for Mac x800
drm/radeon/kms: fix regression in RMX code (v2)
drm: Fix regression in disable polling e58f637
The Thinkpad X100e seems to have some odd behaviour when the display is
powered off - the onboard r8169 starts generating rxfifo overflow errors.
The root cause of this has not yet been identified and may well be a
hardware design bug on the platform, but r8169 should be more resiliant to
this. This patch enables the rxfifo interrupt on 8168 devices and removes
the MAC version check in the interrupt handler, and the machine no longer
crashes when under network load while the screen turns off.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VIAFB_GET_INFO device ioctl allows unprivileged users to read 246
bytes of uninitialized stack memory, because the "reserved" member of
the viafb_ioctl_info struct declared on the stack is not altered or
zeroed before being copied back to the user. This patch takes care of
it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The NXP LPC32XX processor use the same watchdog as the Philips
PNX4008 processor.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since it may be already enabled by bootloader or some other utility. This patch
makes sure that the watchdog is disabled before any userspace daemon opens the
device. It is also required by the watchdog API.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
irq and reboot notifier are acquired in module_init() but never released.
They should be released correctly, otherwise reloading the module or error
during module_init() will cause a problem.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Some pcnet_cs compatible cards require an exact 16-lines match
of the ioport areas specified in CIS, but set the "iolines"
value in the CIS incorrectly. We can easily work around this
issue -- same as we do in serial_cs -- by first trying setting
iolines to the CIS-specified value, and then trying a 16-line
match.
Reported-and-tested-by: Wolfram Sang <w.sang@pengutronix.de>
Hardware-supplied-by: Jochen Frieling <j.frieling@pengutronix.de>
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As the iomem / ioport setup differs per device, it is much better
to print out the device instead of the socket.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
We shouldn't overwrite pre-set values, and we should also
set the port address to the beginning, and not the end of
the 8-port range.
CC: linux-serial@vger.kernel.org
Reported-by: Komuro <komurojun-mbn@nifty.com>
Hardware-supplied-by: Jochen Frieling <j.frieling@pengutronix.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The texture base address registers are in units of 256 bytes.
The original CS checker treated these offsets as bytes, so the
original check was wrong. I fixed the units in a patch during
the 2.6.36 cycle, but this ended up breaking some existing
userspace (probably due to a bug in either userspace texture allocation
or the drm texture mipmap checker). So for now, until we come
up with a better fix, just warn if the mipmap size it too large.
This will keep existing userspace working and it should be just
as safe as before when we were checking the wrong units. These
are GPU MC addresses, so if they fall outside of the VRAM or
GART apertures, they end up at the GPU default page, so this should
be safe from a security perspective.
v2: Just disable the warning. It just spams the log and there's
nothing the user can do about it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.infradead.org/mtd-2.6:
mtd: pxa3xx: fix build error when CONFIG_MTD_PARTITIONS is not defined
mtd: mxc_nand: configure pages per block for v2 controller
mtd: OneNAND: Fix loop hang when DMA error at Samsung SoCs
mtd: OneNAND: Fix 2KiB pagesize handling at Samsung SoCs
mtd: Blackfin NFC: fix invalid free in remove()
mtd: Blackfin NFC: fix build error after nand_scan_ident() change
mxc_nand: Do not do byte accesses to the NFC buffer.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix hiddev's use of usb_find_interface
HID: fixup blacklist entry for Asus T91MT
HID: add device ID for new Asus Multitouch Controller
HID: add no-get quirk for eGalax touch controller
HID: Add quirk for eGalax touch controler.
HID: add support for another BTC Emprex remote control
HID: Set Report ID properly for Output reports on the Control endpoint.
HID: Kanvus Note A5 tablet needs HID_QUIRK_MULTI_INPUT
HID: Add support for chicony multitouch screens.
On resume, before starting the PAL state machine, check if the
adjust_link() method is well supplied. If not, this would lead to a
NULL pointer dereference in the phy_state_machine() function.
This scenario can happen if the Ethernet driver call manually the PHY
functions instead of using the PAL state machine. The mv643xx_eth driver
is a such example.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently brought to my attention that 802.3ad mode bonds would no
longer form when using some network hardware after a driver update.
After snooping around I realized that the particular hardware was using
page-based skbs and found that skb->data did not contain a valid LACPDU
as it was not stored there. That explained the inability to form an
802.3ad-based bond. For balance-alb mode bonds this was also an issue
as ARPs would not be properly processed.
This patch fixes the issue in my tests and should be applied to 2.6.36
and as far back as anyone cares to add it to stable.
Thanks to Alexander Duyck <alexander.h.duyck@intel.com> and Jesse
Brandeburg <jesse.brandeburg@intel.com> for the suggestions on this one.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: stable@kerne.org
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mergeable buffer case, we use headcount, log_num
and seg as indexes in same-size arrays, and
we know that headcount <= seg and
log_num equals either 0 or seg.
Therefore, the right thing to do is range-check seg,
not headcount as we do now: these will be different
if guest chains s/g descriptors (this does not
happen now, but we can not trust the guest).
Long term, we should add BUG_ON checks to verify
two other indexes are what we think they should be.
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV620
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30029
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not 100% sure this is due to BKL removal, its most likely a combination
of that + userspace timing changes in udev/plymouth. The drm adds the sysfs
device before the driver has completed internal loading, this causes udev
to make the node and plymouth to open it before we've completed loading.
The proper solution is to delay the sysfs manipulation until later in loading
however this causes knock on issues with sysfs connector nodes, so we can use
the global mutex to serialise loading and userspace opens.
Reported-by: Toni Spets (hifi on #radeon)
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
My macbook infrared remote control was broken by commit
bd25f4dd69 ("HID: hiddev: use
usb_find_interface, get rid of BKL").
This device appears in dmesg as:
apple 0003:05AC:8242.0001: hiddev0,hidraw0: USB HID v1.11 Device
[Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
It stopped working as lircd was getting ENODEV when opening /dev/usb/hiddev0.
AFAICS hiddev_driver is a dummy driver so usb_find_interface(&hiddev_driver)
does not find anything.
The device is associated with the usbhid driver, so let's do
usb_find_interface(&hid_driver) instead.
$ ls -l /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver
lrwxrwxrwx 1 root root 0 2010-09-12 16:28 /sys/devices/pci0000:00/0000:00:1d.2/usb7/7-1/7-1:1.0/usb/hiddev0/device/driver -> ../../../../../../bus/usb/drivers/usbhid
Signed-off-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We must ensure that ide_proc_port_register_devices() occurs on an
interface before ide_proc_register_driver() executes for that
interfaces drives.
Therefore defer the registry of the driver device objects backed by
ide_bus_type until after ide_proc_port_register_devices() has run
and thus all of the drive->proc procfs directory pointers have been
setup.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: move probe call to subsys_initcall()
powerpc/5200: mpc52xx_uart.c: Add of_node_put to avoid memory leak
spi/pl022: fix APB pclk power regression on U300
spi/spi_s3c64xx: Warn if PIO transfers time out
spi/s3c64xx: Fix incorrect reuse of 'val' local variable.
spi/s3c64xx: Fix compilation warning
spi/dw_spi: clean the cs_control code
spi/dw_spi: Allow interrupt sharing
spi/spi_s3c64xx: Increase dead reckoning time in wait_for_xfer()
spi/spi_s3c64xx: Move to subsys_initcall()
spi: free children in spi_unregister_master, not siblings
gpiolib: Add 'struct gpio_chip' forward declaration for !GPIOLIB case
of: Fix missing includes - ll_temac
spi/spi_s3c64xx: Staticise non-exported functions
spi/spi_s3c64xx: Make probe more robust against missing board config
Smatch complains because we check whether "pch->chan" is NULL and then
dereference it unconditionally on the next line. Partly the reason this
bug was introduced is because code was too complicated. I've simplified
it a little.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes bogus CS rejection if it contains a sequence
of the following operations:
- Set the color buffer 0. track->cb[i].robj becomes non-NULL.
- Render.
- Set a larger zbuffer than the previously-set color buffer.
- Set a larger scissor area as well.
- Set the color channel mask to 0 to do depth-only rendering.
- Render. --> rejected, because track->cb[i].robj remained non-NULL,
therefore the conditional checking for the color channel mask and
friends is not performed, and the larger scissor area causes
the rejection.
This fixes bugs:
- https://bugs.freedesktop.org/show_bug.cgi?id=29762
- https://bugs.freedesktop.org/show_bug.cgi?id=28869
And maybe some others which seem to look the same.
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
One subtest of mesa/demos/gltestperf takes 9 seconds to complete,
so to prevent an unnecessary gpu reset followed by a hardlock, I am
increasing the interval to 10 seconds after which a GPU is considered
in a locked-up state. This is on RV530. However, with a little slower GPU,
we would surpass the interval easily, so this is not a good fix
for gltestperf.
Nevertheless, this commit also fixes hardlocks in the applications which
render at speed of less than 1 frame per second, where the whole frame
consists of only one command stream. The game Tiny & Big is an example.
This bar is now lowered to 0.1 fps.
Now the question comes down to whether we should (often unsuccessfully)
reset the GPU at all? Once we have stable enough drivers, we won't have to.
Has the time come already?
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes rendering errors on some evergreen boards.
Hardcoding the backend map is not an optimal solution, but
a better fix is being worked on.
Similar to the fix for rv740
(6271901d82).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29986
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise when disabling the output we switch to the new fb (which is
likely NULL) and skip the call to mode_set -- leaking driver private
state on the old_fb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
caused by d65d65b175
need to update the radeon crtc priv native mode before using it.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30049
v2: integrate v/h copy paste typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I broke out my trusty i845 and found a new boot failure, which upon
inspection turned out to be a recursion within:
drm_helper_probe_single_connector_modes() -> drm_helper_hpd_irq_event()
-> intel_crt_detect() -> drm_helper_probe_single_connector_modes()
Calling drm_kms_helper_poll_enable() instead performs the desired
re-initialisation of the polling should the user have toggled the
parameter, without the recursive side-effect.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch initializes the pages per block field in CONFIG1 for
v2 controllers. It also sets the FP_INT field. This is the last
field not correctly initialized, so we can switch from
read/modify/write the CONFIG1 reg to just write the correct
value.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When DMA error occurs. it's loop hang since it can't exit the loop.
and it's the right DMA handling code as Spec.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Wrong assumption bufferram can be switched between BufferRAM0 and BufferRAM1
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since info->mtd isn't dynamically allocated, we shouldn't attempt to
kfree() it. Otherwise we get random fun corruption when unloading
the driver built as a module.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Seems some patches got out sync when being merged. The Blackfin NFC
driver was updated to use nand_scan_ident(), but it missed the change
where nand_scan_ident() now takes 3 arguments. So update this driver
to fix build failures.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (28 commits)
ipheth: remove incorrect devtype to WWAN
MAINTAINERS: Add CAIF
sctp: fix test for end of loop
KS8851: Correct RX packet allocation
udp: add rehash on connect()
net: blackhole route should always be recalculated
ipv4: Suppress lockdep-RCU false positive in FIB trie (3)
niu: Fix kernel buffer overflow for ETHTOOL_GRXCLSRLALL
ipvs: fix active FTP
gro: Re-fix different skb headrooms
via-velocity: Turn scatter-gather support back off.
ipv4: Fix reverse path filtering with multipath routing.
UNIX: Do not loop forever at unix_autobind().
PATCH: b44 Handle RX FIFO overflow better (simplified)
irda: off by one
3c59x: Fix deadlock in vortex_error()
netfilter: discard overlapping IPv6 fragment
ipv6: discard overlapping fragment
net: fix tx queue selection for bridged devices implementing select_queue
bonding: Fix jiffies overflow problems (again)
...
Fix up trivial conflicts due to the same cgroup API thinko fix going
through both Andrew and the networking tree. However, there were small
differences between the two, with Andrew's version generally being the
nicer one, and the one I merged first. So pick that one.
Conflicts in: include/linux/cgroup.h and kernel/cgroup.c
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: don't enable self-refresh on Ironlake
drm/i915: Double check that the wait_request is not pending before warning
Revert "drm/i915: Warn if we run out of FIFO space for a mode"
Revert "drm/i915: Allow LVDS on pipe A on gen4+"
Revert "drm/i915: Enable RC6 on Ironlake."
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Range check cpu in blk_cpu_to_group
scatterlist: prevent invalid free when alloc fails
writeback: Fix lost wake-up shutting down writeback thread
writeback: do not lose wakeup events when forking bdi threads
cciss: fix reporting of max queue depth since init
block: switch s390 tape_block and mg_disk to elevator_change()
block: add function call to switch the IO scheduler from a driver
fs/bio-integrity.c: return -ENOMEM on kmalloc failure
bio-integrity.c: remove dependency on __GFP_NOFAIL
BLOCK: fix bio.bi_rw handling
block: put dev->kobj in blk_register_queue fail path
cciss: handle allocation failure
cfq-iosched: Documentation help for new tunables
cfq-iosched: blktrace print per slice sector stats
cfq-iosched: Implement tunable group_idle
cfq-iosched: Do group share accounting in IOPS when slice_idle=0
cfq-iosched: Do not idle if slice_idle=0
cciss: disable doorbell reset on reset_devices
blkio: Fix return code for mkdir calls
We don't know how to enable it safely, especially as outputs turn on and
off. When disabling LP1 we also need to make sure LP2 and 3 are already
disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29173
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29082
Reported-by: Chris Lord <chris@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The 'wwan' devtype is meant for devices that require preconfiguration
and *every* time setup before the ethernet interface can be used, like
cellular modems which require a series of setup commands on serial ports
or other mechanisms before the ethernet interface will handle packets.
As ipheth only requires one-per-hotplug pairing setup with no
preconfiguration (like APN, phone #, etc) and the network interface is
usable at any time after that initial setup, remove the incorrect
devtype wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata-sff: Reenable Port Multiplier after libata-sff remodeling.
libata: skip EH autopsy and recovery during suspend
ahci: AHCI and RAID mode SATA patch for Intel Patsburg DeviceIDs
ata_piix: IDE Mode SATA patch for Intel Patsburg DeviceIDs
libata,pata_via: revert ata_wait_idle() removal from ata_sff/via_tf_load()
ahci: fix hang on failed softreset
pata_artop: Fix device ID parity check
Keep track of the link on the which the current request is in progress.
It allows support of links behind port multiplier.
Not all libata-sff is PMP compliant. Code for native BMDMA controller
does not take in accound PMP.
Tested on Marvell 7042 and Sil7526.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For some mysterious reason, certain hardware reacts badly to usual EH
actions while the system is going for suspend. As the devices won't
be needed until the system is resumed, ask EH to skip usual autopsy
and recovery and proceed directly to suspend.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: Stephan Diestelhorst <stephan.diestelhorst@amd.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the Intel Patsburg (PCH) SATA AHCI and RAID Controller
DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the Intel Patsburg (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 978c0666 (libata: Remove excess delay in the tf_load path)
removed ata_wait_idle() from ata_sff_tf_load() and via_tf_load().
This caused obscure detection problems in sata_sil.
https://bugzilla.kernel.org/show_bug.cgi?id=16606
The commit was pure performance optimization. Revert it for now.
Reported-by: Dieter Plaetinck <dieter@plaetinck.be>
Reported-by: Jan Beulich <JBeulich@novell.com>
Bisected-by: gianluca <gianluca@sottospazio.it>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It was a mistake to mark the PL031 IRQ as shared (for the U8500),
we misread the datasheet. Get rid of this.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the arbitrary software-reset call from the device-probe
method, because:
- It is defective. To work correctly, it should be two byte writes,
not a single word write. As it stands, it does nothing.
- Some devices with sx150x expanders installed have their NRESET pins
ganged on the same line, so resetting one causes the others to reset -
not a nice thing to do arbitrarily!
- The probe, usually taking place at boot, implies a recent hard-reset,
so a software reset at this point is just a waste of energy anyway.
Therefore, make it optional, defaulting to off, as this will match the
common case of probing at powerup and also matches the current broken
no-op behavior.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b485fe5ea ("rtc/m41t80: use rtc_valid_tm() to check returned tm")
added rtc_valid_tm to m41t80_rtc_read_alarm() but it was wrong while the
t->time does not contain complete date/time.
This patch also fixes a warning:
warning: passing argument 1 of 'rtc_valid_tm' from incompatible pointer type
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the second if (reg & ...) test into the branch indicated by its
indentation. The test was previously always executed after the if
containing that branch, but it was always false unless the if branch was
taken.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Pavel Pisa <ppisa@pikron.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If suspend called when kmmcd is doing host->ops->disable, as kmmcd already
increased host->en_dis_recurs to 1, the mmc_host_enable in suspend
function will return directly without increase the nesting_cnt, which will
cause the followed register access carried out to the disabled host.
mmc_suspend_host will enable host itself. No need to enable host before
it. Also works on kmmcd will get flushed in mmc_suspend_host, enable host
after it will be safe. So make the mmc_host_enable after it.
[cjb: rebase against current Linus]
Signed-off-by: Ethan <ethan.too@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following error:
at91_mci.c: In function 'at91_mci_sg_to_dma':
at91_mci.c:236: error: implicit declaration of function 'kmap_atomic'
at91_mci.c:236: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:236: error: (Each undeclared identifier is reported only once
at91_mci.c:236: error: for each function it appears in.)
at91_mci.c:236: warning: assignment makes pointer from integer without a cast
at91_mci.c:252: error: implicit declaration of function 'kunmap_atomic'
at91_mci.c: In function 'at91_mci_post_dma_read':
at91_mci.c:302: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
at91_mci.c:302: warning: assignment makes pointer from integer without a cast
at91_mci.c:317: error: implicit declaration of function 'flush_kernel_dcache_page'
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the following warning:
drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_suspend':
drivers/mmc/host/omap_hsmmc.c:2275: warning: unused variable 'state'
Introduced by commit ID:
commit 1a13f8fa76
Author: Matt Fleming <matt@console-pimps.org>
Date: Wed May 26 14:42:08 2010 -0700
mmc: remove the "state" argument to mmc_suspend_host()
The unique usage of this var was removed there, and missed
removing the respective declaration aswell.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap_atomic() takes the cookie, returned by the kmap_atomic() as its
argument and not the page address, used as an argument to kmap_atomic().
This patch fixes the compile error:
In file included from drivers/mmc/host/tmio_mmc.c:37:
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kunmap_atomic':
drivers/mmc/host/tmio_mmc.h:192: error: negative width in bit-field '<anonymous>'
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Magnus Damm <damm@opensource.se>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, it was possible for ack_mmc_irqs() to clear pending interrupt
bits in the CTL_STATUS register, even though the interrupt handler had not
been called. This was because of a race that existed when doing a
read-modify-write sequence on CTL_STATUS. After the read step in this
sequence, if an interrupt occurred (causing one of the bits in CTL_STATUS
to be set) the write step would inadvertently clear it.
Observed with the TMIO_STAT_RXRDY bit together with CMD53 on AR6002 and
BCM4318 SDIO cards in polled mode.
This patch eliminates this race by only writing to CTL_STATUS and clearing
the interrupts that were passed as an argument to ack_mmc_irqs()."
[matt@console-pimps.org: rewrote changelog]
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>"
Tested-by: Arnd Hannemann <arnd@arndnet.de>"
Acked-by: Ian Molton <ian@mnementh.co.uk>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added missing axis-mapping for HP ProBook 532x and HP Mini 5102.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Much (but not all) of the RTC state is kept in the RTC peripheral which
has its own power domain. Periodically (1 HZ), that state is synced from
one power domain to the other (peripheral->core). When we are resuming,
we need to wait for the sync to occur so that we don't get a mismatch of
reading undefined state in the rest of the driver.
Further, once the externally maintained bits have been synced back into
the core, we then need to restore the bits maintained in the core. In our
particular case, that is just the write completion interrupt bit.
If we don't do any of this, working with the RTC causes ~5 second delays
from time to time after waking up due to the write completion interrupt
never firing.
Reported-by: Michael Dean <mdean@aeronix.com>
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The int_clear helper takes a bitmask of interrupts to keep, not to
disable. When suspending without wakeup enabled, we want to disable
all interrupts, so use 0 (keep none) instead of -1 (keep all).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The introduction of support for SD combo cards breaks the initialization
of all CSR SDIO chips. The GO_IDLE (CMD0) in mmc_sd_get_cid() causes CSR
chips to be reset (this is non-standard behavior).
When initializing an SDIO card check for a combo card by using the memory
present bit in the R4 response to IO_SEND_OP_COND (CMD5). This avoids the
call to mmc_sd_get_cid() on an SDIO-only card.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Acked-by: Michal Mirolaw <mirq-linux@rere.qmqm.pl>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
ARM: Update mach-types
ARM: Partially revert "Auto calculate ZRELADDR and provide option for exceptions"
ARM: Ensure PTE modifications via dma_alloc_coherent are visible
ARM: 6359/1: ep93xx: move clock initialization earlier
Revert "[ARM] pxa: remove now unnecessary dma_needs_bounce()"
ARM: 6352/1: perf: fix event validation
ARM: 6344/1: Mark CPU_32v6K as depended on CPU_V7
ARM: 6343/1: wire up fanotify and prlimit64 syscalls on ARM
ARM: 6330/1: perf: reword comments relating to perf_event_do_pending
ARM: pxa168fb: fix section mismatch
ARM: pxa: Make id const in pwm_probe()
ARM: pxa: fix CI_HSYNC and CI_VSYNC MFP defines for pxa300
ARM: pxa: remove __init from cpufreq_driver->init()
ARM: imx: set cache line size to 64 bytes for i.MX5
mx5/clock: fix clear bit fields issue in _clk_ccgr_disable function
mxc/tzic: add base address when accessing TZIC registers
ARM: mach-shmobile: ap4evb: fix write protect for SDHI1
ARM: mach-shmobile: ap4evb: modify FSI2 ID
ARM: mach-shmobile: do not enable the PLLC2 clock on init
ARM: mach-shmobile: Clock framework comment fix
...
This fixes the prototype for both pci_resource_alignment() and
pci_sriov_resource_alignment().
Patch started as debugging effort from Cam Macdonell.
Cc: Cam Macdonell <cam@cs.ualberta.ca>
Cc: Avi Kivity <avi@redhat.com>
[chrisw: add iov bits]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ahci_do_softreset() compared the current time and deadline in reverse
when calculating timeout for SRST issue. The result is that if
@deadline is in future, SRST is issued with 0 timeout, which hasn't
caused any problem because it later waits for DRDY with the correct
timeout. If deadline is already exceeded by the time SRST is about to
be issued, the timeout calculation underflows and if the device
doesn't respond, timeout doesn't trigger for a _very_ long time.
Reverse the incorrect comparison order.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Gwendal Grignou <gwendal@google.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
x % 1 always evaluates to 0, which clearly isn't the intent. The
author probably had "% 2" or "& 1" in mind, and mispelled it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix hang with modified FIN handling on A0 cards
RDMA/nes: Change state to closing after FIN
RDMA/nes: Fix double CLOSE event indication crash
RDMA/nes: Write correct register write to set TX pause param
RDMA/cxgb3: Don't exceed the max HW CQ depth
we're using a pointer through a freed command to reset the request,
which has shown up as an oops with slab poisoning:
Reported-by: Tejun Heo <tj@kernel.org>
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If we are busy, then we may have woken up the wait_request handler but
not yet serviced it before the hang check fires. So in hang check,
double check that the i915_gem_do_wait_request() is still pending the
wake-up before declaring all hope lost.
Fixes regression with e78d73b16b.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30073
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The PL022 SPI bus is sometimes used for early stuff like
regulators that need to be present at module_init() time, so
we move this to a subsys_initcall().
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use netdev_alloc_skb_ip_align() helper and do correct allocation
Tested-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend, the power.completion is expected to be set when a
device has not yet started suspending. Set it on init to fix a
corner case where a device is resumed when its parent has never
suspended.
Consider three drivers, A, B, and C. The parent of A is C, and C
has async_suspend set. On boot, C->power.completion is initialized
to 0.
During the first suspend:
suspend_devices_and_enter(...)
dpm_resume(...)
device_suspend(A)
device_suspend(B) returns error, aborts suspend
dpm_resume_end(...)
dpm_resume(...)
device_resume(A)
dpm_wait(A->parent == C)
wait_for_completion(C->power.completion)
The wait_for_completion will never complete, because
complete_all(C->power.completion) will only be called from
device_suspend(C) or device_resume(C), neither of which is called
if suspend is aborted before C.
After a successful suspend->resume cycle, where B doesn't abort
suspend, C->power.completion is left in the completed state by the
call to device_resume(C), and the same call path will work if B
aborts suspend.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Changing state to CLOSING when FIN is received causes A0 cards to
hang. Fix this by checking for A0 cards in FIN handling.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the driver receives an AE for FIN received, it closes the
connection without changing the state of the connection in the
hardware to closing. By changing the state to closing, hardware will
do a normal close sequence.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a stress testing in a large cluster, multiple close event are
detected and BUG() is hit in the iWARP core. The cause is that the
active node gave up while waiting for an MPA response from the peer
and tried to close the connection by sending RST. The passive node
driver receives the RST but is waiting for MPA response from the user.
When the MPA accept is received, the driver offloads the connection
and sends a CLOSE event. The driver gets an AE indicating RESET
received and also sends a CLOSE event, hitting a BUG().
Fix this by correcting RESET handling and sending CLOSE events.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Setting TX pause param writes to the wrong register location causing
the adapter to hang. Correct the define used to write the reigster.
Addresses: https://bugs.openfabrics.org/show_bug.cgi?id=2116
Reported-by: Shiri Franchi <shirif@voltaire.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
niu_get_ethtool_tcam_all() assumes that its output buffer is the right
size, and warns before returning if it is not. However, the output
buffer size is under user control and ETHTOOL_GRXCLSRLALL is an
unprivileged ethtool command. Therefore this is at least a local
denial-of-service vulnerability.
Change it to check before writing each entry and to return an error if
the buffer is already full.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
of_node_put(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Ricoh FireWire controllers appear to have the non-atomic cycle
timer register access bug, so, activate the driver workaround by
default.
The behaviour was observed on:
Ricoh Co Ltd R5C552 IEEE 1394 Controller [1180:0552] and
Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (rev 04).
Signed-off-by: Heikki Lindholm <holin@iki.fi>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
With the introduction of an AMBA PrimeCell per-cell block clock,
the pclk was left on after probe() unless explicitly disabled.
This clock is wired to the same clock on PL022 causing it to stay
always on since.
Fix this up properly by clocking the pclk whenever we want to
write into any PL022 registers and clocking the external clock
whenever we want to transmit messages on the bus.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by : Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When using PIO we have a timeout for the TX and RX FIFOs to ensure that
the data actually gets transferred. Warn if we hit that timeout - it
should never happen, but this makes sure we'll find out if it does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Try to handle unknown nmis with an enabled PMU
perf, x86: Fix handle_irq return values
perf, x86: Fix accidentally ack'ing a second event on intel perf counter
oprofile, x86: fix init_sysfs() function stub
lockup_detector: Sync touch_*_watchdog back to old semantics
tracing: Fix a race in function profile
oprofile, x86: fix init_sysfs error handling
perf_events: Fix time tracking for events with pid != -1 and cpu != -1
perf: Initialize callchains roots's childen hits
oprofile: fix crash when accessing freed task structs
Instead of, wrongly, reusing the 'val' variable, use a dedicated
one for reading the status register.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix compilation warning by typecasting the tx_buf pointer.
[I'm not thrilled with resorting to a cast; but I cannot see a better
way to go about this. I don't want to drop the const from struct
spi_transfer ~~glikely]
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 052dc7c45i "spi/dw_spi: conditional transfer mode change"
introduced cs_control code, which has a bug by using bit offset
for spi mode to set transfer mode in control register. Also it
forces devices who don't need cs_control to re-configure the
control registers for each spi transfer. This patch will fix them
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow interrupt sharing since exclusive interrupt line for
DW SPI controller is not provided on every platform.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For small transfers at high speeds the expected transfer time can easily
be well under 1ms, causing the delay in wait_for_xfer() to be only the
dead reckoning fudge factor of 5ms currently included. Experiments on
some of my systems shows that this is marginal for some transfers so
double it to 10ms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow the use of the S3C64xx SPI controller with things like PMICs by
moving the init up to subsys_initcall().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device is handled by hid-mosart driver, and therefore should
be present in hid_blacklist[], not hid_ignore_list[].
Cc: Stephane Chatty <chatty@lii-enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The missing break statement causes wrong capacity calculation for
batteries that report energy.
Reported-by: d binderman <dcb314@hotmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This reverts commit b9421ae8f3.
This warning was so prelevant, even for apparently working machines,
that it was just causing fear, anxiety and panic.
The root cause still remains, so we will add some better debugging when
we focus on fixing it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=17021
Reported-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 0f3ee801b3.
Enabling LVDS on pipe A was causing excessive wakeups on otherwise idle
systems due to i915 interrupts. So restrict the LVDS to pipe B once more,
whilst the issue is properly diagnosed.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16307
Reported-and-tested-by: Enrico Bandiello <enban@postal.uv.es>
Poked-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Adam Jackson <ajax@redhat.com>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
* 'for-linus' of git://neil.brown.name/md:
md: resolve confusion of MD_CHANGE_CLEAN
md: don't clear MD_CHANGE_CLEAN in md_update_sb() for external arrays
Move .gitignore from drivers/md to lib/raid6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
pkt_sched: Fix lockdep warning on est_tree_lock in gen_estimator
ipvs: avoid oops for passive FTP
Revert "sky2: don't do GRO on second port"
gro: fix different skb headrooms
bridge: Clear INET control block of SKBs passed into ip_fragment().
3c59x: Remove incorrect locking; correct documented lock hierarchy
sky2: don't do GRO on second port
ipv4: minor fix about RPF in help of Kconfig
xfrm_user: avoid a warning with some compiler
net/sched/sch_hfsc.c: initialize parent's cl_cfmin properly in init_vf()
pxa168_eth: fix a mdiobus leak
net sched: fix kernel leak in act_police
vhost: stop worker only if created
MAINTAINERS: Add ehea driver as Supported
ath9k_hw: fix parsing of HT40 5 GHz CTLs
ath9k_hw: Fix EEPROM uncompress block reading on AR9003
wireless: register wiphy rfkill w/o holding cfg80211_mutex
netlink: Make NETLINK_USERSOCK work again.
irda: Correctly clean up self->ias_obj on irda_bind() failure.
wireless extensions: fix kernel heap content leak
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: wlan-ng: Explicitly set some fields in cfg80211 interface
Staging: octeon: depends on NETDEVICES
Staging: spectra: depend on X86_MRST
Staging: zram: free device memory when init fails
Staging: rt2870sta: Add more device IDs from vendor drivers
staging: comedi das08_cs.c: Fix io_req_t conversion
staging: spectra needs <linux/slab.h>
staging: hv: Fixed lockup problem with bounce_buffer scatter list
staging: hv: Increased storvsc ringbuffer and max_io_requests
staging: hv: Fixed the value of the 64bit-hole inside ring buffer
staging: hv: Fixed bounce kmap problem by using correct index
staging: hv: Fix missing functions for net_device_ops
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ftdi_sio: Added custom PIDs for ChamSys products
USB: cdc-acm: Fixing crash when ACM probing interfaces with no endpoint descriptors.
USB: cdc-acm: Add pseudo modem without AT command capabilities
USB: cxacru: Use a bulk/int URB to access the command endpoint
usb: serial: mos7840: Add USB IDs to support more B&B USB/RS485 converters.
USB: cdc-acm: Adding second ACM channel support for various Nokia and one Samsung phones
usb: serial: mos7840: Add USB ID to support the B&B Electronics USOPTL4-2P.
USB: ssu100: turn off debug flag
usb: allow drivers to use allocated bandwidth until unbound
USB: cp210x usb driver: add USB_DEVICE for Pirelli DP-L10 mobile.
USB: cp210x: Add B&G H3000 link cable ID
USB: CP210x Add new device ID
USB: option: fix incorrect novatel entries
USB: Fix kernel oops with g_ether and Windows
USB: rndis: section mismatch fix
USB: ehci-ppc-of: problems in unwind
USB: s3c-hsotg: Remove DEBUG define
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix tty_line must not be equal to number of allocated tty pointers in tty driver
serial: bfin_sport_uart: restore transmit frame sync fix
serial: fix port type conflict between NS16550A & U6_16550A
MAINTAINERS: orphan isicom
vt: Fix console corruption on driver hand-over.
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not oops when erroneous PEB is scheduled for scrubbing
UBI: fix kconfig unmet dependency
UBI: fix forward compatibility
UBI: eliminate update of list_for_each_entry loop cursor
* 'drm-intel-fixes' of git://anongit.freedesktop.org/~ickle/drm-intel: (25 commits)
intel_agp,i915: Add more sandybridge graphics device ids
drm/i915: Enable MI_FLUSH on Sandybridge
agp/intel: Fix cache control for Sandybridge
agp/intel: use #ifdef idiom for intel-agp.h
agp/intel: fix physical address mask bits for sandybridge
drm/i915: Prevent double dpms on
drm/i915: Avoid use of uninitialised values when disabling panel-fitter
drm/i915: Avoid pageflipping freeze when we miss the flip prepare interrupt
drm/i915: Tightly scope intel_encoder to prevent invalid use
drm/i915: Allocate the PCI resource for the MCHBAR
drm/i915/dp: Really try 5 times before giving up.
drm/i915/sdvo: Restore guess of the DDC bus in absence of VBIOS
drm/i915/dp: Boost timeout for enabling transcoder to 100ms
drm/i915: Re-use set_base_atomic to share setting of the display registers
drm/i915: Fix offset page-flips on i965+
drm/i915: Include a generation number in the device info
i915: return -EFAULT if copy_to_user fails
i915: return -EFAULT if copy_to_user fails
agp/intel: Promote warning about failure to setup flush to error.
drm/i915: overlay on gen2 can't address above 1G
...
It causes all kinds of DMA API debugging assertions and
all straight-forward attempts to fix it have failed.
So turn off SG, and we'll tackle making this work
properly in net-next-2.6
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a simplified version of the original patch from James Courtier-Dutton.
>From: James Courtier-Dutton
>Subject: [PATCH] Fix b44 RX FIFO overflow recovery.
>Date: Wednesday, June 30, 2010 - 1:11 pm
>
>This patch improves the recovery after a RX FIFO overflow on the b44
>Ethernet NIC.
>Before it would do a complete chip reset, resulting is loss of link
>for a few seconds.
>This patch improves this to do recovery in about 20ms without loss of link.
>
>Signed off by: James@superbug.co.uk
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug introduced in commit
de84727214
"3c59x: Use fine-grained locks for MII and windowed register access".
vortex_interrupt() holds vp->window_lock over multiple register
accesses to reduce locking overhead. However it also needs to call
vortex_error() sometimes, and that uses the regular functions for
access to windowed registers, which will try to acquire window_lock
again.
Therefore, drop window_lock around the call to vortex_error() and set
the window afterward reacquiring the lock. Since vortex_error() may
call vortex_rx(), which *does* require its caller to hold window_lock,
lift that call up into vortex_interrupt(). This also removes the
potential for calling vortex_rx() on a later-generation NIC.
Reported-and-tested-by: Jens Schüßler <jgs@trash.net> [in Debian's 2.6.32]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The time_before_eq()/time_after_eq() functions operate on unsigned
long and only work if the difference between the two compared values
is smaller than half the range of unsigned long (31 bits on i386).
Some of the variables (slave->jiffies, dev->trans_start, dev->last_rx)
used by bonding store a copy of jiffies and may not be updated for a
long time. With HZ=1000, time_before_eq()/time_after_eq() will start
giving bad results after ~25 days.
jiffies will never be before slave->jiffies, dev->trans_start,
dev->last_rx by more than possibly a couple ticks caused by preemption
of this code. This allows us to detect/prevent these overflows by
replacing time_before_eq()/time_after_eq() with time_in_range().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot use spinlock when kmalloc is invoked with
GFP_KERNEL flag because it can sleep.
So this patch reviews the usage of spinlock within the
stmmac_resume function avoing this bug.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ce17178094.
This commit has been independently bisected a few times as being the cause
of a s2ram failure.
Reported-and-tested-by: Kyle McMartin <kyle@mcmartin.ca>
Reported-and-tested-by: Andy Isaacson <adi@hexapodia.org>
Cc: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit 409f3499a2 (scsi/sd: remove big
kernel lock) introduced a bug in the sd_release routine. Medium
removal should be allowed when the number of open file references
drops to 0, not when it becomes non-zero.
This patch (as1414) adjusts the test to fix the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
New pci ids for GT2 and GT2+ on desktop and mobile sandybridge,
and graphics device ids for server sandybridge. Also rename original
ids string to reflect GT1 version.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
MI_FLUSH is being deprecated, but still available on Sandybridge.
Make sure it's enabled as userspace still uses MI_FLUSH.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Sandybridge GTT has new cache control bits in PTE, which controls
graphics page cache in LLC or LLC/MLC, so we need to extend the mask
function to respect the new bits.
And set cache control to always LLC only by default on Gen6.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It should shift bit 39-32 into pte's bit 11-4.
Reported-by:Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Arguably this is a bug in drm-core in that we should not be called twice
in succession with DPMS_ON, however this is still occuring and we see
FDI link training failures on the second call leading to the occassional
blank display. For the time being ignore the repeated call.
Original patch by Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
We were passing garbage values into the panel-fitter control register
when disabling it on Ironlake - those values (filter modes and reserved
MBZ bits) would have then be re-used the next time panel-fitting was
enabled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When we miss the flip prepare interrupt, we never get into the
software state needed to restart userspace, resulting in a freeze of a
full-screen OpenGL application (such as a compositor).
Work around this by checking DSPxSURF/DSPxBASE to see if the page flip
has actually happened. If it has, do the work we would have done when
the flip prepare interrupt comes in.
Also, add debugfs information to tell us what's going on (based on the
patch from Chris Wilson attached to bugs.fdo bug #29798).
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We reset intel_encoder for every matching encoder whilst iterating over
the encoders attached to this crtc when changing mode. As such in a
cloned configuration intel_encoder may not correspond to the correct
is_edp encoder.
By scoping intel_encoder to the loop, not only is the compiler able to
spot this mistake, we also improve readiability for ourselves.
[It might not be a mistake, within this function it is unclear as to
whether it is permissable for eDP to be cloned...]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were failing when trying to allocate the resource for MMIO of the
MCHBAR because we forgot to specify what type of resource we wanted.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Only stop trying if the aux channel sucessfully reports that the
transmission was completed, otherwise try again. On the 5th failure,
bail and report that something is amiss.
This fixes a sporadic failure in reading the EDID for my external panel
over DP.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
If the VBIOS tells us the mapping of the SDVO device onto the DDC bus,
use it. However, if there is no VBIOS available that mapping is
uninitialised and we should fallback to our earlier guess.
Fix regression introduced in b1083333 (which in turn is a fix for the
regression caused by the introduction of this guess, 14571b4).
References:
Bug 29499 - [945GM] Screen disconnected because of missing VBIOS
https://bugs.freedesktop.org/show_bug.cgi?id=29499
Bug 15109 - i945GM fails to detect EDID on DVI port
https://bugzilla.kernel.org/show_bug.cgi?id=15109
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Paul Neumann <paul104x@yahoo.de>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: stable@kernel.org
Adam Hill reported that his Arrandale system required a much longer, up
to 200x500us, wait for the panel to initialise or else modesetting would
fail.
References:
https://bugs.freedesktop.org/show_bug.cgi?id=29141
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Adam Hill <sidepipeuk@yahoo.co.uk>
i965 uses the Display Registers to compute the offset from the display
base so the new base does not need adjusting when flipping. The older
chipsets use a fence to access the display and so do perceive the
surface as linear and have a single base register which is reprogrammed
using the flip.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: Marty Jack <martyj19@comcast.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
copy_to_user() returns the number of bytes remaining to be copied and
I'm pretty sure we want to return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
copy_to_user returns the number of bytes remaining to be copied, but we
want to return a negative error code here. These are returned to
userspace.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Make sure we always detect when we fail to correctly allocate the Isoch
Flush Page and print an error to warn the user about the likely memory
corruption that will result in invalid rendering or worse.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
So set the coherent dma mask accordingly. This dma mask is only used
for physical objects, so it won't really matter allocation-wise.
Now this never really surfaced because sane 32bit kernels only have 1G
of lowmem. But some eager testers (distros?) still carry around the patch
to adjust lowmem via a kconfig option. And the kernel seems to favour
high allocations on boot-up, hence the overlay blowing up reliably.
Because the patch is tiny and nicely shows how broken gen2 is it's imho
worth to merge despite the fact that mucking around with the lowmem/
highmem division is (no longer) supported.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=28318
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The vblank status bit is a sticky bit that must be cleared with a write
of '1' prior to polling for the next vblank.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
jbarnes: I'd still rather see a lock, but I think you're right that
we don't generally wait in code that needs not to miss an interrupt.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Partial revert of 9d0498a2bf.
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Tested-by: Hugh Dickins <hughd@google.com>
Tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This fixes blur-like screen corruption on the following card:
VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller [8086:29c2] (rev 10)
intel_sdvo_mode_set() should not return prematurely just because some
features are not supported.
https://bugzilla.kernel.org/show_bug.cgi?id=17151
Signed-off-by: Pavel Roskin <proski@gnu.org>
Reported-by: Jonathan Corbet <corbet@lwn.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[ickle: Relax a couple more checks for failing LVDS modesetting]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit 86f100b136.
The kref API requires the handlecount to be initialised to one on object
creation (so that kref_get() doesn't complain upon first use) so the
dalliance in the drivers is required in order to sink the initial
floating reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
drivers/gpu/drm/i915/intel_overlay.c: In function 'intel_overlay_print_error_state':
drivers/gpu/drm/i915/intel_overlay.c:1467: error: implicit declaration of function 'seq_printf'
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16811
Reported-by: Martin Ziegler <ziegler@uni-freiburg.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Andre Muller <andremuellerster@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Only fallback to a set of default modes on a connector iff that
connector is known to be connected. The issue occurs that with limited
hardware which cannot probe a connector and so reports the
connector status as unknown will then attempt to retrieve the modes for
it during drm_helper_probe_single_connector_modes(). Should that fail,
the helper then generates a default set which fools the fb_helper and
causes havoc with the console and beyond.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
digital underscan support regressed tv-out.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29985
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These VGT regs need to be programmed via the ring rather than
MMIO as on previous asics (r6xx/r7xx).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In wm8350_dcdc_set_mode(), we set DCx_SLEEP bit of WM8350_DCDC_SLEEP_OPTIONS
register for REGULATOR_MODE_STANDBY mode.
( DCx_SLEEP bits: 0: Normal DC-DC operation 1: Select LDO mode )
In wm8350_dcdc_get_mode(), current logic to determinate
REGULATOR_MODE_STANDBY mode is just reverse.
( sleep is set should mean REGULATOR_MODE_STANDBY mode. )
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Problem description in current implementation:
When setting REGULATOR_MODE_IDLE mode, current implementation set
WM831X_LDO1_LP_MODE bit of ctrl_reg (which is wrong, it should clear the bit).
But due to a missing break statement for case REGULATOR_MODE_IDLE, the code
fall through to case REGULATOR_MODE_STANDBY and then clear
WM831X_LDO1_LP_MODE bit. So it still looks OK when checking the status
by wm831x_gp_ldo_get_mode().
When setting REGULATOR_MODE_STANDBY mode, it just does not work.
wm831x_gp_ldo_get_mode() will still return REGULATOR_MODE_IDLE because
the accordingly WM831X_LDO1_LP_MODE bit is clear.
Correct behavior should be:
Clear WM831X_LDO1_LP_MODE bit of ctrl_reg for REGULATOR_MODE_IDLE mode.
Set WM831X_LDO1_LP_MODE bit of ctrl_reg for REGULATOR_MODE_STANDBY mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
vhost should set worker to NULL on cgroups attach failure,
so that we won't try to destroy the worker again on close.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since 2.6.36-rc1, non-root users of vhost-net fail to attach
if they are in any cgroups.
The reason is that when qemu uses vhost, vhost wants to attach
its thread to all cgroups that qemu has. But we got the API backwards,
so a non-priveledged process (Qemu) tried to control
the priveledged one (vhost), which fails.
Fix this by switching to the new cgroup_attach_task_all,
and running it from the vhost thread.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For ISP82xx, the check for empty slot in request queue before posting command type 6
request was missing. This could lead to request queue entry corruptions causing
IO timeouts.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, if target sets the SCSI Status (with Check condition)
and there is no FCP residual bit set then driver does not check
for dropped frame. This could lead to data corruption.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fw_hung flag should be set ir-respective of if there is a
mbx command pending or not. Also the complete should be called
if there is a mbx waiting.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The seconds_since_last_heartbeat should be checked for consecutive
heartbeat checks. Currently it could happen that seconds_since_last_heartbeat
gets set to max (2 seconds) for non-consecutive heartbeat checks.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
selector is used as array index of info->supported_voltages
Thus the valid value range should be 0 .. info->voltages_len -1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@openource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In choose_voltage(), we use i as array index of info->vol_table.
The valid value range for i should be 0 .. ARRAY_SIZE(info->vol_table) - 1.
Take LDO1 as example, ARRAY_SIZE(LDO1_table) is 4, vol_nbits of LDO1 is 2.
for (i = 0; i < (2 << info->vol_nbits); i++) is equivalent to
for (i = 0; i < 8; i++)
which is wrong.
The same value range checking also applies for index in pm8607_list_voltage().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@openource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The cfg80211 api has introduced a few new fields. Rather than assume
what cfg80211 api does by default, set these explicitly.
Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lld_nand fails to build on arches without virt_to_bus. Since this driver
is specifically for hardware enablment on Moorestown, this patch adds
Moorestown MID support as a dependency.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taken from DPO_RT3070_LinuxSTA_V2.3.0.4_20100604.tar.bz2 and
2010_0709_RT2870_Linux_STA_v2.4.0.1.tar.bz2, with duplicates removed.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 90abdc3b9 converted all PCMCIA users away from io_req_t. In
das08_cs.c the converted IO lines mask setting was added but the old
line using the now inexistent p_dev->io was not removed.
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On one of my m68k test builds I get:
drivers/staging/spectra/ffsport.c: In function ‘ioctl_read_page_data’:
drivers/staging/spectra/ffsport.c:196: error: implicit declaration of function ‘kmalloc’
drivers/staging/spectra/ffsport.c:196: warning: assignment makes pointer from integer without a cast
drivers/staging/spectra/ffsport.c:212: error: implicit declaration of function ‘kfree’
drivers/staging/spectra/ffsport.c: In function ‘ioctl_write_page_data’:
drivers/staging/spectra/ffsport.c:229: warning: assignment makes pointer from integer without a cast
drivers/staging/spectra/ffsport.c: In function ‘SBD_setup_device’:
drivers/staging/spectra/ffsport.c:637: warning: assignment makes pointer from integer without a cast
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed lockup problem with bounce_buffer scatter list which caused
crashes in heavy loads. And minor code indentation cleanup in effected
area.
Removed whitespace and noted minor indentation changes in description as
pointed out by Joe Perches. (Thanks for reviewing Joe)
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increased storvsc ringbuffer and max_io_requests. This now more
closely mimics the numbers on Hyper-V. And will allow more IO requests
to take place for the SCSI driver.
Max_IO is set to double from what it was before, Hyper-V allows it and
we have had appliance builder requests to see if it was a problem to
increase the number.
Ringbuffer size for storvsc is now increased because I have seen A few buffer
problems on extremely busy systems. They were Set pretty low before.
And since max_io_requests is increased I Really needed to increase the buffer
as well.
Signed-off-by:Hank Janssen <hjanssen@microsoft.com>
Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed the value of the 64bit-hole inside ring buffer, this
caused a problem on Hyper-V when running checked Windows builds.
Checked builds of Windows are used internally and given to external
system integrators at times. They are builds that for example that all
elements in a structure follow the definition of that Structure. The bug
this fixed was for a field that we did not fill in at all (Because we do
Not use it on the Linux side), and the checked build of windows gives
errors on it internally to the Windows logs.
This fixes that error.
Signed-off-by:Hank Janssen <hjanssen@microsoft.com>
Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixed bounce offset kmap problem by using correct index.
The symptom of the problem is that in some NAS appliances this problem
represents Itself by a unresponsive VM under a load with many clients writing
small files.
Signed-off-by:Hank Janssen <hjanssen@microsoft.com>
Signed-off-by:Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix missing functions for net_device_ops.
It's a bug when porting the drivers from 2.6.27 to 2.6.32. In 2.6.27,
the default functions for Ethernet, like eth_change_mtu(), were assigned
by ether_setup(). But in 2.6.32, these function pointers moved to
net_device_ops structure and no longer be assigned in ether_setup(). So
we need to set these functions in our driver code. It will ensure the
MTU won't be set beyond 1500. Otherwise, this can cause an error on the
server side, because the HyperV linux driver doesn't support jumbo frame
yet.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain USB devices, such as the Nokia X6 mobile phone, don't expose any
endpoint descriptors on some of their interfaces. If the ACM driver is forced
to probe all interfaces on a device the a NULL pointer dereference will occur
when the ACM driver attempts to use the endpoint of the alternative settings.
One way to get the ACM driver to probe all the interfaces is by using the
/sys/bus/usb/drivers/cdc_acm/new_id interface.
This patch checks that the endpoint pointer for the current alternate settings
is non-NULL before using it.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm.c : Manage pseudo-modem without AT commands capabilities
Enable to drive electronic simple gadgets based on microcontrolers.
The Interface descriptor is like this:
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0 None
Signed-off-by: Philippe Corbes <philippe.corbes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The command endpoint is either a bulk or interrupt endpoint, but using
the wrong type of transfer causes an error if CONFIG_USB_DEBUG is
enabled after commit f661c6f8c6, which
checks for this mismatch.
Detect which type of endpoint it is and use a bulk/int URB as
appropriate. There are other function calls specifying a bulk pipe,
but usb_clear_halt doesn't use the pipe type (only the endpoint) and
usb_bulk_msg auto-detects interrupt transfers.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable <stable@kernel.org> [.34 and newer]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB IDs needed to support the B&B USOPTL4-4P, USO9ML2-2P, and
USO9ML2-4P. This patch expands and corrects a typo in the patch sent
on 08-31-2010.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
S60 phones from Nokia and Samsung expose two ACM channels. The first is a modem
with a standard AT-command interface, which is picked up correctly by CDC-ACM.
The second ACM port is marked as having a vendor-specific protocol. This means
that the ACM driver will not claim the second channel by default.
This adds support for the second ACM channel for the following devices:
Nokia E63
Nokia E75
Nokia 6760 Slide
Nokia E52
Nokia E55
Nokia E72
Nokia X6
Nokia N97 Mini
Nokia 5800 Xpressmusic
Nokia E90
Samsung GTi8510 (INNOV8)
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB ID needed to support B&B Electronic's 2-port, optically-isolated,
powered, USB to RS485 converter.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using the remove sysfs file, the device configuration is set to -1
(unconfigured). This eventually unbind drivers with the bandwidth_mutex
held. Some drivers may call functions that hold said mutex, like
usb_reset_device. This is the case for rtl8187, for example. This will
lead to the same process holding the mutex twice, which deadlocks.
Besides, according to Alan Stern:
"The deadlock problem probably could be handled somehow, but there's a
separate issue: Until the usb_disable_device call finishes unbinding
the drivers, the drivers are free to continue using their allocated
bandwidth. We musn't change the bandwidth allocations until after the
unbinding is done. So this patch is indeed necessary."
Unbinding the driver before holding the bandwidth_mutex solves the
problem. If any operation after that fails, drivers are not bound again.
But that would be a problem anyway that the user may solve resetting the
device configuration to one that works, just like he would need to do in
most other failure cases.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Pirelli DP-L10 mobile is sold under various brand names. One, already
supported by cp210x, is the T-COM TC300. Here is the lsusb for that version:
-------------------------------------------------------------------
Bus 001 Device 002: ID 0489:e000 Foxconn / Hon Hai T-Com TC 300
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe000 T-Com TC 300
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 TC 300
iSerial 3 0001
[snip]
---------------------------------------------------------------------------
However the native Pirelli DP-L10 is not supported:
------------------------------------------------------------------
Bus 001 Device 003: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe003 Pirelli DP-L10
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 DP-L10
iSerial 3 0001
[snip]
-------------------------------------------------------------------------
All that is required is an extra USB_DEVICE entry:
{ USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM
+Mobile */
The patch adds that entry. Tested under 2.6.36-rc2 from git.
Signed-off-by: A E Lawrence <lawrence_a_e@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New device ID added for Balluff RFID reader.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately some of the hardware PID belonging to auto-install CDROM
(AICD) of Novatel modems found their way into the option module. This
causes the AICD to be treated as a modem in stead of a disk. Since the
modem ports do not appear until after the AICD is ejected, this
essentially disables the modem. After a couple of minutes the AICD
should auto-eject, but it is just too long a wait. The frequency of the
failure seems to depend on both the hardware and the linux distribution.
Here is a patch that fixes this up, and also adds a couple of new PID,
offering some explanations and removing some incomplete and unnecessary
comments.
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the following section mismatch warning,
by moving the function rndis_init() from .init.text to .text.
WARNING: vmlinux.o(.text+0x1aeca5a): Section mismatch in reference from the function rndis_bind_config() to the function .init.text:rndis_init()
The function rndis_bind_config() references
the function __init rndis_init().
This is often because rndis_bind_config lacks a __init
annotation or the annotation of rndis_init is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The iounmap(ehci->ohci_hcctrl_reg); should be the first thing we do
because the ioremap() was the last thing we did. Also if we hit any of
the goto statements in the original code then it would have led to a
NULL dereference of "ehci". This bug was introduced in: 796bcae736
"USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]"
I modified the few lines in front a little so that my code didn't
obscure the return success code path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DEBUG is defined unconditionally, remove it as this clutters the message log.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found a bug "by chance" in drivers/char/tty_io.c
I mean "by chance" because I was just reading the code of the
tty_find_polling_driver() to make a new tty_find_by_name() function.
In tty_find_polling_driver() the driver actually test "tty_line <=
p->num" while num refers to the number of struct tty_struct pointers
allocated for the p->ttys (p is a tty_driver), and tty_line is scanned
in a tty name, which can be for example ttyS2. Then tty_line equals 2.
And if p->num is 2, we have only p->ttys[0] and p->ttys[1], but no
p->ttys[2].
This is actually unharmful, for tty_find_polling_driver() is used only
in drivers/serial/kgdboc.c, and there's a test over there to find a
console with a matching index, which will never happen.
This is still a bug anyway.
Signed-off-by: Nathael Pajani <nathael.pajani@ed3l.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The large cleanup/rewrite of resources in commit ccf68e59e9
accidentally reverted an earlier fix in commit a19e8b2059.
So restore it here.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: stable <stable@kernel.org> [.34 and newer]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After 02f0777a0d "vc_origin" is no
longer reset to the screen buffer before calling the con_init() hook
of the new console driver.
If the old driver wasn't using a fixed scanout buffer (e.g. the case
of vgacon) "vc_origin" may be a pointer to a VRAM location, and its
contents aren't guaranteed to be preserved after calling con_deinit()
on the old driver and con_init() on the new driver, i.e. the
subsequent console resize may fill the framebuffer with garbage.
It can be reproduced in the transition from vgacon to the nouveau
framebuffer driver: in that case the legacy VGA aperture "vc_origin"
points to becomes unreadable after fbcon_init().
This patch reverts the mentioned commit. To avoid the problem it
intended to fix, stop using "vc_scr_end" in vc_do_resize() to
calculate how many rows we have to copy (actually the code looks
simpler this way without the help of "vc_scr_end").
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Cc: qiaochong <qiaochong@loongson.cn>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Async notifications other than link status are possible in certain
configurations. Remove the BUG_ON in the mcc completion processing path.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ONLINE registers can return 0xFFFFFFFF on more than one
occassion. On systems that care, reading these registers could
lead to problems.
So the new code decides that the ASIC has encountered and error
by reading the UE_STATUS_LOW/HIGH registers. AND them with
the mask values and a non-zero result indicates an error.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong packet statistics for multicast Rx was causing net-snmp error messages
every 15 seconds. Instead of picking the multicast stats from hardware,
now maintain it in the driver itself.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add no-get quirk for eGalax touch controller to avoid timeout at probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nv50: initialize ramht_refs list for faked 0 channel
drm/nouveau: Don't take struct_mutex around the pushbuf IOCTL.
drm/nouveau: Take fence spinlock before reading the last sequence.
We need it for PFIFO_INTR_CACHE_ERROR interrupt handling,
because nouveau_fifo_swmthd looks for matching gpuobj in
ramht_refs list.
It fixes kernel panic in nouveau_gpuobj_ref_find.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We don't need it and it can lead to lock order inversions with respect
to drm_global_mutex, potentially causing dead locks.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It fixes a race between the TTM delayed work queue and the GEM IOCTLs
(fdo bug 29583) uncovered by the BKL removal.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The max depth supported by T3 is 64K entries. This fixes a bug
introduced in commit 9918b28d ("RDMA/cxgb3: Increase the max CQ
depth") that causes stalls and possibly crashes in large MPI clusters.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
GCC warns about empty printf format strings, and after
the addition of %pV these existing such cases in the
scsi driver layer were exposed enough for the compiler
to start seeing them.
Based almost entirely upon a patch by Joe Perches.
[jejb: fix up sym53c8xx msg]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
warning: zero-length gnu_printf format string
Fix the above warning by inserting a space into the literal string.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The doorbell reset initially appears to work correctly,
the controller resets, comes up, some i/o can even be
done, but on at least some Smart Arrays in some servers,
it eventually causes a subsequent controller lockup due
to some kind of PCIe error, and kdump can end up leaving
the root filesystem in an unbootable state. For this
reason, until the problem is fixed, or at least isolated
to certain hardware enough to be avoided, the doorbell
reset should not be used at all.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The current code in tree has problems with Login.
This patch fixes the Login Failure .
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
[mnc: Can't believe I missed that.]
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Return of the bi_rw tests is no longer bool after commit 74450be1. So
testing against constants doesn't make sense anymore. Fix this bug in
osd_req_read by removing "== 1" in test.
This is not a problem now, where REQ_WRITE is 1, but this can change
in the future and we don't want to rely on that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This reverts commit de6be6c1f7.
After some discussion with Jarek Poplawski and Eric Dumazet, we've
decided that this change is incorrect.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 7th entry in a lot of evergreen i2c gpio tables is partially
zeroed. Fix the entry.
Should fix the missing ddc entry in:
https://bugs.freedesktop.org/show_bug.cgi?id=29255
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The tv parameter was added to disable the tv-out connector,
however, it caused a crash if it was set to 0 due to
drm_connector_init not getting called. If tv=0, don't
attempt to add the connector.
Might fix:
https://bugzilla.kernel.org/show_bug.cgi?id=17241
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV515
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This code was originally for forcing some clocks on certain asics.
However, this code was later moved to asic specific functions
for all of the affected asics. The only users of the original
code at this point were r600, rv770, and evergreen and the code
was not relevant for those asics. So, remove it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vortex_ioctl() was grabbing vortex_private::lock around its call to
generic_mii_ioctl(). This is no longer necessary since there are more
specific locks which the mdio_{read,write}() functions will obtain.
Worse, those functions do not save and restore IRQ flags when locking
the MII state, so interrupts will be enabled when generic_mii_ioctl()
returns.
Since there is currently no need for any function to call
mdio_{read,write}() while holding another spinlock, do not change them
to save and restore IRQ flags but remove the specification of ordering
between vortex_private::lock and vortex_private::mii_lock.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's something very important I forgot to tell you.
What?
Don't cross the GRO streams.
Why?
It would be bad.
I'm fuzzy on the whole good/bad thing. What do you mean, "bad"?
Try to imagine all the Internet as you know it stopping instantaneously
and every bit in every packet swapping at the speed of light.
Total packet reordering.
Right. That's bad. Okay. All right. Important safety tip. Thanks, Hubert
The simplest way to stop this is just avoid doing GRO on the second port.
Very few Marvell boards support two ports per ring, and GRO is just
an optimization.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus resources must be released on exit
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its currently illegal to call kthread_stop(NULL)
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduced by 49dce689 ("spi doesn't need class_device") and bad-fixed
by 350d0076 ("spi: fix double-free on spi_unregister_master"),
spi_unregister_master would previously device_unregister all of the spi
master's siblings (instead of its children). hilarity ensues.
fix it to unregister children.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It is the next patch which is fixing missing header
which were removed from prom.h.
Related patches:
"of/address: Clean up function declarations" (sha1 id 22ae782f8)
"of: Fix missing includes" (sha1 id f1ca09b2b)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The S3C64xx SPI driver requires the machine to call s3c64xx_spi_set_info()
to select a few options, including the clock to use for the SPI controller.
If this is not done then a NULL will be passed as the clock name for
clk_get(), causing an obscure crash. Guard against this and other missing
configuration by validating that the clock name has been filled in in
the platform data that ets passed in.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, the address return from regulator_register()
is different from the address for regulator_unregister().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
max8998->dev is NULL in current implementation, set it to &pdev->dev.
regulator_register() still return success if max8998->dev is NULL,
but rdev->dev.parent will be set to NULL which is incorrect.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The third parameter of tps6586x_set_bits() is the bit_mask,
thus we should use (1 << ri->go_bit) instead of ri->go_bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
val is used as array index of ri->voltages.
Thus the valid value range should be 0 .. ri->desc.n_voltages - 1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Set max8998->num_regulators = pdata->num_regulators,
otherwise it's default value is 0.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We only use max8998->rdev[0] .. max8998->rdev[pdata->num_regulators-1],
max8998->rdev[pdata->num_regulators] is not used.
Thus fix the memory allocation size.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This driver is a platform driver, not a i2c driver.
Thus remove incorrect tps6507x_remove comments.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
A little bit improvement in the logic of choosing selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, ab8500_regulator_info[0].regulator is not
unregistered if the error happen at i > 0.
This patch fixes the resource leak and also improves the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, ab3100_regulators[0].rdev is not unregistered if
the error happen at i > 0.
This patch fixes the resource leak and also improves the readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I moved the dereference of "ab8500" below the check for NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We need to call platform_device_unregister(i8042_platform_device)
before calling platform_driver_unregister() because i8042_remove()
resets i8042_platform_device to NULL. This leaves the platform device
instance behind and prevents driver reload.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=16613
Reported-by: Seryodkin Victor <vvscore@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
By visual inspection, the reported touch_major and touch_minor axes
are a factor of two too small. Presumably the device actually reports
the semi-major and semi-minor axes. Corrected with this patch.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The 5 GHz CTL indexes were not being read for all hardware
devices due to the masking out through the CTL_MODE_M mask
being one bit too short. Without this the calibrated regulatory
maximum values were not being picked up when devices operate
on 5 GHz in HT40 mode. The final output power used for Atheros
devices is the minimum between the calibrated CTL values and
what CRDA provides.
Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM is compressed on AR9003, upon decompression
the wrong upper limit was being used for the block which
prevented the 5 GHz CTL indexes from being used, which are
stored towards the end of the EEPROM block. This fix allows
the actual intended regulatory limits to be used on AR9003
hardware.
Cc: stable@kernel.org [2.6.36+]
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
