* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Don't use the EFI reboot method by default
x86, suspend: Restore MISC_ENABLE MSR in realmode wakeup
x86, reboot: Acer Aspire One A110 reboot quirk
x86-32, NUMA: Fix boot regression caused by NUMA init unification on highmem machines
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (31 commits)
sctp: fix missing send up SCTP_SENDER_DRY_EVENT when subscribe it
net: refine {udp|tcp|sctp}_mem limits
vmxnet3: round down # of queues to power of two
net: sh_eth: fix the parameter for the ETHER of SH7757
net: sh_eth: fix cannot work half-duplex mode
net: vlan: enable soft features regardless of underlying device
vmxnet3: fix starving rx ring whenoc_skb kb fails
bridge: Always flood broadcast packets
greth: greth_set_mac_add would corrupt the MAC address.
net: bind() fix error return on wrong address family
natsemi: silence dma-debug warnings
net: 8139too: Initial necessary vlan_features to support vlan
Fix call trace when interrupts are disabled while sleeping function kzalloc is called
qlge:Version change to v1.00.00.29
qlge: Fix printk priority so chip fatal errors are always reported.
qlge:Fix crash caused by mailbox execution on wedged chip.
xfrm4: Don't call icmp_send on local error
ipv4: Don't use ufo handling on later transformed packets
xfrm: Remove family arg from xfrm_bundle_ok
ipv6: Don't put artificial limit on routing table size.
...
The driver shouldn't override vt->type, and the tuner name should be
based on vt->type as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers must be able to rely on s_power to power up subdevices.
Note that at this moment no driver attempts to power up tuners. This probably
isn't surprising since s_power(1) was never implemented in tuner-core.c until
now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prohibit attempts to change the tuner to a type that is different
from the device node the ioctl is called from. I.e. the type must
be RADIO for a radio node and ANALOG_TV for a video/vbi node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of a number of unnecessary tuner_dbg messages by simplifying
the std fixup function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner ops g_frequency, g_tuner and s_tuner require that the tuner type
field is filled in. Document this.
The tuner-core doc is based on a patch from Mauro Carvalho Chehab <mchehab@redhat.com>.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Radio devices have weird side-effects when used with combined TV/radio
tuners and the V4L2 spec is ambiguous on how it should work. This results
in inconsistent driver behavior which makes life hard for everyone.
Be more strict in when and how the switch between radio and tv mode
takes place and make sure all drivers behave the same.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix typo: g_tuner should have been s_tuner.
Tested with a bttv card.
Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner-core subdev requires that the type field of v4l2_tuner is
filled in correctly. This is done in v4l2-ioctl.c, but pvrusb2 doesn't
use that yet, so we have to do it manually based on whether the current
input is radio or not.
Tested with my pvrusb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Mike Isely <isely@pobox.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The subdevs are supposed to receive a valid tuner type for the g_frequency
and g/s_tuner subdev ops. Some drivers do this, others don't. So prefill
this in v4l2-ioctl.c based on whether the device node from which this is
called is a radio node or not.
The spec does not require applications to fill in the type, and if they
leave it at 0 then the 'check_mode' call in tuner-core.c will return
an error and the ioctl does nothing.
Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
set_mode is called with t->type, which is the tuner type. Instead, use
t->mode which is the actual tuner mode (i.e. radio vs tv).
Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both s_std and s_tuner are broken because set_mode_freq is called before the
new std (for s_std) and audmode (for s_tuner) are set.
This patch splits set_mode_freq in a set_mode and a set_freq and in s_std/s_tuner
first calls set_mode, and if that returns 0 (i.e. the mode is supported)
then they set t->std/t->audmode and call set_freq.
This fixes a bug where changing std or audmode would actually change it to
the previous value.
Discovered while testing analog TV standards for cx18 with a tda18271 tuner.
Cc: stable@kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously we would check for acpi_sci_override_gsi == gsi every time
a PCI device was enabled. That works during early bootup, but later
on it could lead to triggering unnecessarily the acpi_gsi_to_irq(..) lookup.
The reason is that acpi_sci_override_gsi was declared in __initdata and
after early bootup could contain bogus values.
This patch moves the check for acpi_sci_override_gsi to the
site where the ACPI SCI is preset.
CC: stable@kernel.org
Reported-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
Tested-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
[http://lists.xensource.com/archives/html/xen-devel/2011-07/msg00154.html]
Suggested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some newly added drivers do not set backlight type, as a result
/sys/class/backlight/<backlight>/type shows incorrect backlight type.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Handle events 0x4010 and 0x4011 so that we do not pester users about them.
These events report when the thinkpad is docked/undocked to a native
hotplug dock (i.e. one that does not need ACPI handling, nor is represented
in the ACPI device tree). Such docks are based on USB 2.0/3.0, and also
work as port replicators.
We really want a proper dock class to report these, or at least new input
EV_SW events. Since it is not clear which one to use yet, keep reporting
them as vendor-specific ThinkPad events.
WARNING: As defined by the thinkpad-acpi sysfs ABI rules of engagement, the
vendor-specific events will be REMOVED as soon as generic events are made
available (duplicate events are a big problem), with an appropriate update
to the thinkpad-acpi sysfs/event ABI versioning. Userspace is already
prepared to provide easy backwards compatibility for such changes when
convenient to the distro (see acpi-fakekey).
* Event 0x4010: docking to hotplug dock/port replicator
* Event 0x4011: undocking from hotplug dock/port replicator
Typical usecase would be to trigger display reconfiguration.
Reports mention T410, T510, and series 3 docks/port replicators. Special
thanks to Robert de Rooy for his extensive report and analysis of the
situation.
http://www.thinkwiki.org/wiki/ThinkPad_Port_Replicator_Series_3http://www.thinkwiki.org/wiki/ThinkPad_Mini_Dock_Series_3http://www.thinkwiki.org/wiki/ThinkPad_Mini_Dock_Plus_Series_3http://www.thinkwiki.org/wiki/ThinkPad_Mini_Dock_Plus_Series_3_for_Mobile_Workstationshttp://lenovoblogs.com/insidethebox/?p=290
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Reported-by: Claudius Hubig <claudiushubig@chubig.net>
Reported-by: Doctor Bill <docbill@gmail.com>
Reported-by: Korte Noack <gbk.noack@gmx.de>
Reported-by: Robert de Rooy <robert.de.rooy@gmail.com>
Reported-by: Sebastian Will <swill@csail.mit.edu>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
data is not freed in the error case of
compal_probe().
Signed-off-by: Andre Bartke <andre.bartke@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Handle some user interface events from the newer Lenovo models. We are likely
to do something smart with these events in the future, for now, hide the ones
we are already certain about from the user and userspace both.
* Events 0x6000 and 0x6005 are key-related. 0x6005 is not properly identified
yet. Ignore these events, and do not report them.
* Event 0x6040 has not been properly identified yet, and we don't know if it
is important (looks like it isn't, but still...). Keep reporting it.
* Change the message the driver outputs on unknown 0x6xxx events, as all
recent events are not related to thermal alarms. Degrade log level from
ALERT to WARNING.
Thanks to all users who reported these events or asked about them in a number
of mailing lists. Your help is highly appreciated, even if I did took a lot of
time to act on them. For that I apologise.
I will list those that identified the reasons for the events as "reported-by",
and I apologise in advance if I leave anyone out: it was not done on purpose, I
made the mistake of not properly tagging all event report emails separately,
and might have missed some.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reported-by: Markus Malkusch <markus@malkusch.de>
Reported-by: Peter Giles <g1l3sp@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fix a bitwise bug that was found by Joern Heissler, it must be OR
but not AND when we query current device state.
Acked-by: Joern Heissler <linux-acpi@joern.heissler.de>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
acer-wmi is indiscriminately using the device state from hotkey
events to update the various rfkill states. On the Aspire 1830 this
can result in a soft block on the wlan when the touchpad hotkey is
pressed, as it is reporting a non-zero device state that does not
reflect the wireless status. To fix this, only update rfkill states
when a wlan or bluetooth hotkey is pressed.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This platform has not been converted to 'struct irq_data' when the big
pile was done. It fails to compile nowadays, because the compatibility
code has gone.
CC arch/arm/mach-vt8500/irq.o
arch/arm/mach-vt8500/irq.c:118:2: error: unknown field 'ack' specified in initializer
arch/arm/mach-vt8500/irq.c:118:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:119:2: error: unknown field 'mask' specified in initializer
arch/arm/mach-vt8500/irq.c:119:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:120:2: error: unknown field 'unmask' specified in initializer
arch/arm/mach-vt8500/irq.c:120:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:121:2: error: unknown field 'set_type' specified in initializer
arch/arm/mach-vt8500/irq.c:121:2: warning: initialization from incompatible pointer type
make[1]: *** [arch/arm/mach-vt8500/irq.o] Error 1
Add the missing conversion. Tested on a JayPC-Tablet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alexey Charkov <alchark@gmail.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
To get hundredths of MHz the rate needs to be divided by 10'000.
Here is an example:
twd_timer_rate = 123456789
Before the patch:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 1000000) % 100 = 23
Result: 123.23MHz.
After being fixed:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 10000) % 100 = 45
Result: 123.45MHz.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We forgot to send up SCTP_SENDER_DRY_EVENT notification when
user app subscribes to this event, and there is no data to be
sent or retransmit.
This is required by the Socket API and used by the DTLS/SCTP
implementation.
Reported-by: Michael Tüxen <Michael.Tuexen@lurchi.franken.de>
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Tested-by: Robin Seggelmann <seggelmann@fh-muenster.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing suggests that at least some Lenovos and some Intels will
fail to reboot via EFI, attempting to jump to an unmapped
physical address. In the long run we could handle this by
providing a page table with a 1:1 mapping of physical addresses,
but for now it's probably just easier to assume that ACPI or
legacy methods will be present and reboot via those.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/1309985557-15350-1-git-send-email-mjg@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sometimes we could be controlling a device (such as an NVIDIA Tesla) that
has no crtcs/encoders/connectors.
One could argue that the driver should unset DRIVER_MODESET in this case,
but that changes a whole heap of the DRM's other behaviours, and it's much
easier to just be a modesetting driver without any outputs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ib pool weren't free for various newer asic on module unload.
This doesn't cause much arm but still could be candidate for
stable.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Current tcp/udp/sctp global memory limits are not taking into account
hugepages allocations, and allow 50% of ram to be used by buffers of a
single protocol [ not counting space used by sockets / inodes ...]
Lets use nr_free_buffer_pages() and allow a default of 1/8 of kernel ram
per protocol, and a minimum of 128 pages.
Heavy duty machines sysadmins probably need to tweak limits anyway.
References: https://bugzilla.stlinux.com/show_bug.cgi?id=38032
Reported-by: starlight <starlight@binnacle.cx>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the dual-adc switching mode is active in Realtek auto-parser,
we need to couple all ADCs as a single capture-volume. Currently, the
volume control changes only the first ADC, thus others may remain silent.
This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
vmxnet3 device supports only power-of-two number of queues. The driver
therefore needs to check this and rounds down the number of queues to the
nearest power of two.
Signed-off-by: Yong Wang <yongwang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Dmitry Torokhov <dtor@vmware.com>
Some BIOSes will reset the Intel MISC_ENABLE MSR (specifically the
XD_DISABLE bit) when resuming from S3, which can interact poorly with
ebba638ae7. In 32bit PAE mode, this can
lead to a fault when EFER is restored by the kernel wakeup routines,
due to it setting the NX bit for a CPU that (thanks to the BIOS reset)
now incorrectly thinks it lacks the NX feature. (64bit is not affected
because it uses a common CPU bring-up that specifically handles the
XD_DISABLE bit.)
The need for MISC_ENABLE being restored so early is specific to the S3
resume path. Normally, MISC_ENABLE is saved in save_processor_state(),
but this happens after the resume header is created, so just reproduce
the logic here. (acpi_suspend_lowlevel() creates the header, calls
do_suspend_lowlevel, which calls save_processor_state(), so the saved
processor context isn't available during resume header creation.)
[ hpa: Consider for stable if OK in mainline ]
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Link: http://lkml.kernel.org/r/20110707011034.GA8523@outflux.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@kernel.org> 2.6.38+
A user reported an error where if we try to balance an fs after a device has
been removed it will blow up. This is because we get an EIO back and this is
where BUG_ON(ret) bites us in the ass. To fix we just exit. Thanks,
Reported-by: Anand Jain <Anand.Jain@oracle.com>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
There are three missed mount options settable by user which are not
currently displayed in mount output.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When inodes are marked stale in a transaction, they are treated
specially when the inode log item is being inserted into the AIL.
It tries to avoid moving the log item forward in the AIL due to a
race condition with the writing the underlying buffer back to disk.
The was "fixed" in commit de25c18 ("xfs: avoid moving stale inodes
in the AIL").
To avoid moving the item forward, we return a LSN smaller than the
commit_lsn of the completing transaction, thereby trying to trick
the commit code into not moving the inode forward at all. I'm not
sure this ever worked as intended - it assumes the inode is already
in the AIL, but I don't think the returned LSN would have been small
enough to prevent moving the inode. It appears that the reason it
worked is that the lower LSN of the inodes meant they were inserted
into the AIL and flushed before the inode buffer (which was moved to
the commit_lsn of the transaction).
The big problem is that with delayed logging, the returning of the
different LSN means insertion takes the slow, non-bulk path. Worse
yet is that insertion is to a position -before- the commit_lsn so it
is doing a AIL traversal on every insertion, and has to walk over
all the items that have already been inserted into the AIL. It's
expensive.
To compound the matter further, with delayed logging inodes are
likely to go from clean to stale in a single checkpoint, which means
they aren't even in the AIL at all when we come across them at AIL
insertion time. Hence these were all getting inserted into the AIL
when they simply do not need to be as inodes marked XFS_ISTALE are
never written back.
Transactional/recovery integrity is maintained in this case by the
other items in the unlink transaction that were modified (e.g. the
AGI btree blocks) and committed in the same checkpoint.
So to fix this, simply unpin the stale inodes directly in
xfs_inode_item_committed() and return -1 to indicate that the AIL
insertion code does not need to do any further processing of these
inodes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
All the blkio.throttle.* file names are incorrectly reported without
".throttle" in the documentation. Fix it.
Signed-off-by: Andrea Righi <andrea@betterlinux.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The list of available general purpose memory allocators in
Documentation/CodingStyle chapter 14 is incomplete. This patch adds
the missing vzalloc() to the list.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move location of quilt series for kernel-doc patches.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
...as that makes for a cumbersome interface. Make it take a regular
smb_vol pointer and rely on the caller to zero it out if needed.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Regression introduced by commit f87d39d951.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This call to cifs_cleanup_volume_info is clearly wrong. As soon as it's
called the following call to cifs_get_tcp_session will oops as the
volume_info pointer will then be NULL.
The caller of cifs_mount should clean up this data since it passed it
in. There's no need for us to call this here.
Regression introduced by commit 724d9f1cfb.
Reported-by: Adam Williamson <awilliam@redhat.com>
Cc: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The l2x0_disable function attempts to writel with the l2x0_lock held.
This results in deadlock when the writel contains an outer_sync call
for the platform since the l2x0_lock is already held by the disable
function. A further problem is that disabling the L2 without flushing it
first can lead to the spin_lock operation becoming visible after the
spin_unlock, causing any subsequent L2 maintenance to deadlock.
This patch replaces the writel with a call to writel_relaxed in the
disabling code and adds a flush before disabling in the control
register, preventing livelock from occurring.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It was discovered by Roberto Bergo, that RTS/DTR signals are inverted after
the boot, because it was causing him problems with hardware controlled modem
connected on ttyAM0. Todd Valentic came with this patch for the issue.
Discussion: http://tech.groups.yahoo.com/group/ts-7000/message/20259
Comments from Petr Štetiar:
Sorry, but forget to add Acked-by[1]:
1. https://patchwork.kernel.org/patch/873052/
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Todd Valentic <todd.valentic@sri.com>
Tested-by: Roberto Bergo <roberto.bergo@robson.it>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds