UVC makefile defines obj as:
obj-$(CONFIG_USB_VIDEO_CLASS) := uvcvideo.o
Instead of:
obj-$(CONFIG_USB_VIDEO_CLASS) += uvcvideo.o
Due to that, if uvc is selected, all obj-y or obj-m that were added to
compilation were forget. This breaks a proper kernel build.
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver supports video input devices compliant with the USB Video Class
specification. This means lots of currently manufactured webcams, and probably
most of the future ones.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134 driver uses a (non-atomic) variable in an attempt to
only allow one opener of the device (how it deals with sending
the fd over unix sockets I don't know).
Unfortunately, the release function first decrements this variable,
and THEN goes on to disable more of the device. This allows for
a race where another opener of the device comes in after the decrement of
the variable, configures the hardware just to then see the hardware
be disabled by the rest of the release function.
This patch makes the release function use the same lock as the open
function to protect the hardware as well as the variable (which now
at least has some locking to protect it).
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move allocation after first check and fix memory leak.
Noticed-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch ensures that the xc5000 will have firmware loaded as needed if the
part is powered down or reset via gpio from the host. An example of this, in
some cases, could be after the system resumes from standby or hibernate modes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This decreases scan time in Queens, New York from 28 minutes to 7 minutes,
with the exact same services found.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDIOC_ENUMSTD did not return all the PAL/SECAM/NTSC variants: it just returned
one single PAL/SECAM/NTSC standard without separate entries for the trickier
standards like NTSC-JP.
Changed the code so that it behaves better.
Also simplified the if/switch statements into a common standards lookup table.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix uncorrected block counter and bit error rate to follow DVB API spec:
- Unsupported controls return -ENOSYS.
- UNC must never be set to 0.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the i2c write fails during initialisation, an oops happens
because state->frontend.dvb is still undefined. Fixed.
Thanks to Sigmund Augdal for reporting this bug,
and to Hartmut Birr for suggesting the fix.
Thanks-to: Sigmund Augdal <sigmund@snap.tv>
Thanks-to: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Fix S-Video and Compsite input settings for the Yuan MPC718 per user
reports from Yuri Warczynski <Yuri.Warczynski@gmail.com> and
Brian Hope <brian@hopefamily.info> and enable the card entry. The tuner reset
GPIO pin is likely incorrect as the tuner firmware cannot be reloaded without a
reboot. It is likely the audio routing is done via GPIO which is not
implemented yet, as users report audio doesn't work for some inputs.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Add I2C slave reset via GPIO upon initialization. One user,
Michael <msd4824@yahoo.com>, has reported this allows his HVR-1600 EEPROM to
be consistently recognized when using (long,) 100 msec delays. The delays in
this commit are nominal (10 & 40 msec) and need testing/tuning on boards with
I2C problems to find the right values.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a fix for the case when a digital capture from dvr0 happens first after
modprobe, before access to any cx18 v4l2 device nodes. The initial dvb feed
start has been changed to load the firmware if not already loaded. Also fixed a
use counter to correct dvb feed accounting if starting the transport DMA fails.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the cx18-cards.c structures for the HVR-1600 to reflect that audio Line In 2
and FM radio audio go to AIN3 and AIN4 of the CS5345 mux respectively. Verified
by physical inspection of an HVR-1600MCE, by listening to FM broadcasts with the
HVR-1600MCE, and by comparing with the card definition for a PVR-150 in ivtv.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the cx18-av-core code so that accesses to cx23418 av core that
cause auto-configuration will be adjusted to emulate the auto-configuration
behavior of the cx25843. This fixes the VBI displayed as video at the top of
the frame for NTSC and probably other things.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The automatic Kconfig selection for tuners and frontends should be
conditional, based on !DVB_FE_CUSTOMISE.
This patch corrects the selection for VIDEO_CX18 on
MEDIA_TUNER_MXL5005S and DVB_S5H1409
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the current modulation and frequency is already set to
the desired parameters, then don't re-tune.
Don't store current frequency until after we've tuned successfully.
Force a re-tune after resume from standby.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the umt-010 driver the struct umt_properties sets the number of URBs for
transfer to 20. But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10.
Not surprisingly this causes an oops for all devices which use the umt-010
chipset when they are inserted.
fix on Kaffeine channel scan for
Initialize stream count using MAX_NO_URBS_FOR_DATA_STREAM.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Devices can either be class devices or bus devices, not both at the
same time. Soc-camera host devices usually have a platform device as
their parent. Trying to also register them with a class crashes the
kernel, when linked statically. Interestingly, it works when built
as a module. Thanks to Paulius Zaleckas for reporting.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
platform_get_irq() returns a negative value on error, not 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Having the thermometer on during channel configuration
could cause tuning instability.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The TDA18271HD/C1 rf_cal map lookup is expected to go out of range outside
of the frequency window 41 MHz - 61.1 MHz. In these cases, the internal
RF tracking filters calibration mechanism is used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IF notch bit gets unset when we update the Main Post Div register
value, before we have a chance to write the desired IF notch setting
to the tuner. Move the IF notch configuration to after we update MPD.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an error occurs at firmware loading, sometimes, tda1004x stops answering.
Instead of reporting such error, attach code were assuming that the device were
answering an invalid ID (0xff). This can be seen when enabling debug options:
tda1004x: tda1004x_read_byte: reg=0x0
tda1004x: tda1004x_read_byte: error reg=0x0, ret=-5
Now, instead of reporting an invalid ID, it will report the correct error:
tda10046: chip is not answering. Giving up.
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
A possible improvement would be trying to reset the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A fresh copy of v.29 firmware, using get_firmware, is leading to an invalid
firmware:
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision ff -- invalid
tda1004x: trying to boot from eeprom
tda1004x: found firmware revision ff -- invalid
tda1004x: waiting for firmware upload...
tda1004x: Error during firmware upload
tda1004x: found firmware revision ff -- invalid
tda1004x: firmware upload failed
Sometimes, loading/unloading this firmware makes tda1004x to return an invalid
ID. However, there were no printk messages to help to identify what were the
cause for the error.
With this patch, it will now print:
Invalid tda1004x ID = 0xff. Can't proceed
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
Tested with LifeView FlyDVB-T Hybrid Cardbus/MSI TV @nywhere A/D NB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Describe exactly that only s-video and composite input are working on Avermedia
A700
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
decrementing dev->empress_users should be done as last action of ts_release,
because it sleeps and write access to dev->empress_started is not protected
in any way
(additionally closing thread could mute audio after opening thread unmuted it)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-audio.c
em28xx-dvb.c
- Em28xx extensions should ensure they are being only loaded against devices
that support them. Deals with case where there are multiple em28xx
devices, some of which have DVB (or ALSA) support and some do not.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c
- DVB support is supposed to be enabled for the first generation HVR-900.
This device was confirmed with DVB by mkrufky when we did the original work
in April, but I guess we forgot to set the flag.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-video.c
- Properly handle loading of the module when multiple devices are already
connected (such as at bootup). Before we were only calling dvb_init()
against the last device in the list, so while we were handling subsequent
adds properly, if there were multiple devices present on driver load,
everybody except the last device would not get initialized.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18-cards.h had a copy of the audio and video input enums
from cx18-av-core.h, but with different prefixes. Removed
that copy and used the ones from cx18-av-core.h.
Thanks to Andy Walls <awalls@radix.net> for the report.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The S-Video LUMA input was restricted to the In1-In4 inputs, but it
turns out that it can use the full range of In1-In8.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to timf <timf@iinet.net.au> and Mike Galbraith <efault@gmx.de> to report
this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Put explicit lock_kernel() calls into videodev_open(). That function
itself seems OK, but one never knows about all the open() functions
provided by underlying video drivers.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Check that tda827x_config is defined before attempting to use it.
Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On the TDA18271HD/C1, we perform RF tracking filter correction for VHF low
band, only. If supplied a frequency out of range, the error must be returned
to the caller (tda18271c1_rf_tracking_filter_calibration) so that it can
decide whether or not to write to register EB14, RFC_CPROG[7:0]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Testing whether xceive_pin is non-zero is not good enough as 0 is a valid
value. Instead explicitly test whether the Xceive tuner is used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is patch for fix data structure in querycap syscall.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-tip testing found the following build failure:
LD .tmp_vmlinux1
drivers/built-in.o: In function `generic_set_freq':
tuner-xc2028.c:(.text+0xbd896): undefined reference to `request_firmware'
tuner-xc2028.c:(.text+0xbdd7a): undefined reference to `release_firmware'
drivers/built-in.o: In function `xc_load_fw_and_init_tuner':
xc5000.c:(.text+0xc68e6): undefined reference to `request_firmware'
xc5000.c:(.text+0xc6abe): undefined reference to `release_firmware'
with this config:
http://redhat.com/~mingo/misc/config-Tue_May_20_18_11_34_CEST_2008.bad
the reason is another kconfig tool bug that has to be worked around in
the driver's Kconfig file: if FW_LOADER is selected in a second
dependency, that is not properly propagated up the dependencies.
in this case, FW_LOADER is selected from MEDIA_TUNER_XC2028:
config MEDIA_TUNER_XC2028
tristate "XCeive xc2028/xc3028 tuners"
depends on VIDEO_MEDIA && I2C
depends on HOTPLUG
select FW_LOADER
which got selected by MEDIA_TUNER:
config MEDIA_TUNER
tristate
default VIDEO_MEDIA && I2C
depends on VIDEO_MEDIA && I2C
select FW_LOADER if !MEDIA_TUNER_CUSTOMIZE && HOTPLUG
but the kconfig tool did not pick up this second-order dependency and
allowed CONFIG_FW_LOADER=m to be selected - in which case the build
fails.
the workaround i found was to move the select of FW_LOADER one level up,
so that the buggy kconfig tool can notice it and can act appropriately.
This problem can probably be worked around in other ways as well, i went
for the minimal fix.
Obviously, the kconfig tool should be fixed, it is not reasonable to
expect driver authors to do manual dependency resolution (that kconfig
itself already does) and uglify the Kconfig files. The kconfig tool did
nothing to warn about this situation and did not prevent this faulty
.config from being constructed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
direct dereferencing from user-supplied address
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Endianness annotations and fixes + fixing the handling of
->uncorrected_block_count
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use a standard method to manage multiple instances of a hybrid tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Create a macro to report the number of instances of the tuner driver
currently in use. This will allow drivers to perform specific cleanups
before destroying the last instance of a tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The gpio_dir/val statics cannot be global, they are card-specific.
Thanks to Andy Walls for pointing this out.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I always assumed that the Compro H900 could do digital as well,
but it turned out that it is an analog-only card.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The HVR-1600 can do both analog and digital capture at the same time.
Due to a driver bug -EBUSY would be returned when attempting to setup an
analog capture while a digital capture was already in progress.
Separate the two internally.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The handling of the audio registers 808 and 80c were based on old datasheets.
Updated to the latest information.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner_warn() macro relies on the local variable "priv" to be a valid
pointer. There was a case in simple_tuner_attach() where this cannot be the
case yet, so tuner_warn() would dereference a NULL "priv" pointer. Changed
the tuner_warn() to a printk() with the originally intended output format.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This code is irrelevant to this driver and should be removed. This was
copied from a hack in cx88-dvb.c, which prevents noise coming from the
analog tuner (via an audio patch cable from the pci card to the sound
hardware) when in digital mode by muting the tda988x. This issue does
not apply to this USB hybrid chip design, where a single piece of
silicon handles both analog and digital demodulation.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
somebody forgot to to fix this header...
Thanks to Ingo Molnar for pointing this out.
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
testing of the -tip tree found the following build failures on
2.6.26-rc3:
drivers/built-in.o: In function `ttusb_dec_disconnect':
ttusb_dec.c:(.text+0xa2c95): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `dvb_usb_read_remote_control':
dvb-usb-remote.c:(.text+0xa6a94): undefined reference to `input_event'
with this config:
http://redhat.com/~mingo/misc/config-Tue_May_20_03_48_57_CEST_2008.bad
these are due to the media/dvb/usb layer having dependencies on INPUT
functionality, without having that spelled out in the Kconfig file.
this patch makes that dependency explicit (for the drivers affected),
which solves the build error.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After commit 039d40019f
(V4L/DVB (7898): Fix VIDEO_MEDIA Kconfig logic)
VIDEO_MEDIA is no longer usable in Makefile's for deciding
which directories we enter, resulting in compile errors like the
following with CONFIG_VIDEO_DEV=y, CONFIG_DVB_CORE=m:
<-- snip -->
...
MODPOST 187 modules
...
make[2]: *** [__modpost] Error 1
<-- snip -->
The easiest solution is to always enter video/
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It doesn't seem to be intended that "tuner_modu_type" and
"MXL5005_ControlName" were global variables.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
check_v4l2 always returns 0, so this change is an noop for now,
but a comment says it will return something else in the future
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
change check_mode and set_mode to return negative errors and fix all callers
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
locking-add-typecheck-on-irqsave-and-friends-for-correct-flags.patch will cause
drivers/media/video/zoran_driver.c: In function 'zoran_close_end_session':
drivers/media/video/zoran_driver.c:1172: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner driver used to change i2c_client.name for its own needs, but
it really shouldn't, as this field is used by i2c-core to do the
device/driver matching. So, create and use a separate field for the
tuner driver needs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
vidiocgmbuf() does this:
mutex_lock(&fh->cap.vb_lock);
retval = videobuf_mmap_setup(&fh->cap, gbuffers, gbufsize,
V4L2_MEMORY_MMAP);
and videobuf_mmap_setup() then just does
mutex_lock(&q->vb_lock);
ret = __videobuf_mmap_setup(q, bcount, bsize, memory);
mutex_unlock(&q->vb_lock);
which is an obvious double-take deadlock.
This patch fixes this by having vidiocgmbuf() just call the
__videobuf_mmap_setup function instead.
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reported-by: Koos Vriezen <koos.vriezen@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c/max6875: Really prevent 24RF08 corruption
i2c-amd756: Fix functionality flags
i2c: Kill the old driver matching scheme
i2c: Convert remaining new-style drivers to use module aliasing
i2c: Switch pasemi to the new device/driver matching scheme
i2c: Clean up Blackfin BF527 I2C device declarations
i2c-nforce2: Disable the second SMBus channel on the DFI Lanparty NF4 Expert
i2c: New co-maintainer
Update all the remaining new-style i2c drivers to use standard module
aliasing instead of the old driver_name/type driver matching scheme.
Note that the tuner driver is a bit quirky at the moment, as it
overwrites i2c_client.name with arbitrary strings. We write "tuner"
back on remove, to make sure that driver cycling will work properly,
but there may still be troublesome corner cases.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As reported by Ingo Molnar:
x86.git testing found the following build failure:
drivers/built-in.o: In function `pvr2_dvb_feed_thread':
pvrusb2-dvb.c:(.text+0x127e78): undefined reference to `dvb_dmx_swfilter'
drivers/built-in.o: In function `pvr2_dvb_adapter_exit':
pvrusb2-dvb.c:(.text+0x128357): undefined reference to `dvb_net_release'
pvrusb2-dvb.c:(.text+0x12836f): undefined reference to `dvb_dmxdev_release'
[...]
with this config:
CONFIG_VIDEO_PVRUSB2=y
CONFIG_DVB_CORE=m
i.e. pvrusb2 is built-in, dvb-core is modular.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- MEDIA_ATTACH now applies also for V4L;
- select a FW_LOADER dependent driver should happen only if HOTPLUG;
- apply the common tuner dependency to all tuners. This helps to avoid latter
issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If one of DVB_CORE or VIDEO_DEV is a module, the modules that can be used by
both DVB and V4L cores should also be a module, otherwise, it will break its
dependencies. This Kconfig logic implements the following:
CONFIG_VIDEO_DEV CONFIG_DVB_CORE CONFIG_VIDEO_MEDIA
N N N
N M M
N Y Y
M N M
M M M
M Y M
Y N Y
Y M M
Y Y Y
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The current code passes a context pointer in the xc5000_config struct.
This context pointer is used in the tuner_callback function, used to
reset the device after firmware download.
The xc5000_config struct is a static structure, whose .priv member was
being assigned before calling xc5000_attach(). If there are more than
one of the same device type installed on a single system, the last one
to assign xc5000_config.priv will "win", and all others will cease to
function properly.
This patch passes the context pointer in xc5000_attach() rather that
storing it within the static struct xc5000_config.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Upon error conditions in cx18/ivtv_probe(), the code at the 'err:' label
leaves a NULL entry in cx18/ivtv_cards[]. This can cause a NULL pointer
de-reference in cx18/ivtv_v4l2_open() which is fixed by this patch.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner, S-Video and Composite are all working for the Compro H900.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
patch 779169257208 made the variable mask unnecessary.
This patch just removes the declaration.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This causes a problem with the audio mute on some cards and is done
implictly in the audio initialization code.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I was informed by Jan Hoogenraad that two people needed to be removed
from the original copyright comments.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ensure we have the correct .h dependencies included.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
4 exceptions where the code would read very ugly otherwise.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ATSC and QAM should be working but basic testing is required.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Initial check-in of the original driver to establish history.
Signed-off-by: Chia-Ling Lu Developer <chialing@realtek.com.tw>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch does some small cleanup to mt312.
It changes kconfig description to also list the ZL10313.
It does change some strange symbol names to be consistent with
module name mt312 and naming of all other functions in there.
* vp310_mt312_ops -> mt312_ops
* vp310_mt312_attach -> mt312_attach
Adds a MODULE_AUTHOR for me
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
x86.git testing found the following build bug on latest -git:
CC [M] drivers/media/video/mt9v022.o
drivers/media/video/mt9v022.c: In function 'bus_switch_request':
drivers/media/video/mt9v022.c:199: error: implicit declaration of function 'gpio_is_valid'
drivers/media/video/mt9v022.c:201: error: implicit declaration of function 'gpio_request'
drivers/media/video/mt9v022.c:207: error: implicit declaration of function 'gpio_direction_output'
drivers/media/video/mt9v022.c:211: error: implicit declaration of function 'gpio_free'
drivers/media/video/mt9v022.c: In function 'bus_switch_act':
drivers/media/video/mt9v022.c:237: error: implicit declaration of function 'gpio_set_value_cansleep'
make[2]: *** [drivers/media/video] Error 2
make[1]: *** [drivers/media] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [drivers] Error 2
with this config:
http://redhat.com/~mingo/misc/config-Sat_May__3_16_08_39_CEST_2008.bad
the bug was that the driver uses GPIO functionality but only includes
the GPIO interface definitions for the CONFIG_MT9M001_PCA9536_SWITCH
case, which was not set in this config.
The quick fix seems to be to include linux/gpio.h unconditionally. (this
seems like a small cleanup as well as it removes and #ifdef is more
robust than an inclusion of asm/gpio.h) Not tested too much yet, so
please have another look in any case.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
itd1000_fre_values[] can become static const.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- cx18-i2c.c should #include "cx18-i2c.h" for getting the prototypes of
it's global functions
- make the following needlessly global functions static:
- cx18-fileops.c:cx18_claim_stream()
- cx18-fileops.c:cx18_release_stream()
- cx18-queue.c:cx18_queue_move()
- remove the following unused functions:
- cx18-driver.c:cx18_waitq()
- cx18-queue.c:cx18_buf_copy_from_user()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- don't show kernel backtrace when the allocation of the buffers fails: the
normal ivtv/cx18 messages are clear enough and the backtrace scares users.
- fix cleanup after the buffer allocation fails (caused kernel panic).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix compile warnings if MODULE is not defined.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since:
1) FW_LOADER is defined as:
config FW_LOADER
tristate "Userspace firmware loading support"
depends on HOTPLUG
2) several V4L/DVB driver just selects it;
3) select is not smart enough to auto-select HOTPLUG, if select FW_LOADER.
So, All drivers that select FW_LOADER should also depend on HOTPLUG.
An easier solution (for the end-user perspective) would be to "select HOTPLUG".
However, live is not simple. This would cause recursive dependency issues like
this one:
drivers/usb/Kconfig:62:error: found recursive dependency: USB -> USB_OHCI_HCD
-> I2C -> MEDIA_TUNER -> MEDIA_TUNER_XC2028 -> HOTPLUG -> PCCARD -> PCMCIA ->
USB_ARCH_HAS_HCD -> MOUSE_APPLETOUCH -> USB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88 doesn't need support for FW_LOADER. Instead, this is required only for
cx88-blackbird.
Also, cx88-blackbird depends on HOTPLUG, due to FW_LOADER dependency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-dvb doesn't need FW_LOADER. Instead, tuner-xc2028 needs to select
FW_LOADER.
Also, this can happen only if HOTPLUG is selected, since FW_LOADER
is dependent on HOTPLUG.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since all tuners are dependent of I2C, move I2C dependency to MEDIA_TUNER.
Also, simplifies the dependencies for the other Kconfig items.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_TUNER is responsible for compilation of tuners.ko module. This were the
previous behaviour before the creation of MEDIA_TUNER.
Before this patch, tuner.ko were created even for drivers that don't need a
tuner (like webcam drivers).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only show debug from tda18271_set_standby_mode if DBG_ADV is set.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Abort rf band calibration loop for the TDA18271HD/C2 if an error is detected.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
x86.git testing found the following build bug in v2.6.26-rc1:
drivers/built-in.o: In function `cinergyt2_probe':
cinergyT2.c:(.text+0xb6117): undefined reference to `input_allocate_device'
cinergyT2.c:(.text+0xb6230): undefined reference to `input_register_device'
cinergyT2.c:(.text+0xb623d): undefined reference to `input_free_device'
with the following config:
http://redhat.com/~mingo/misc/config-Sun_May__4_22_06_54_CEST_2008.bad
The reason for the bug is that the cinergyT2 driver depends on
CONFIG_INPUT functionality, but if INPUT is modular it's still possible
to build CONFIG_DVB_CINERGYT2=y - which leads to missing symbols.
The solution is to make DVB_CINERGYT2 dependent on INPUT.
[ This solves the build problem - i have not tested the driver on this card. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix undefined references in au0828:
depends on USB and select VIDEO_TVEEPROM
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
x86.git testing found the following build failure in v2.6.26-rc1:
MODPOST 424 modules
ERROR: "tveeprom_hauppauge_analog" [drivers/media/video/au0828/au0828.ko] undefined!
ERROR: "tveeprom_read" [drivers/media/video/au0828/au0828.ko] undefined!
with this config:
http://redhat.com/~mingo/misc/config-Sat_May__3_22_28_58_CEST_2008.bad
this patch does what other video drivers do to utilize the
VIDEO_TVEEPROM functionality (and this resolves the build problem) - but
i have not checked it on real hardware and i have not checked whether
the fix is complete.
selections, so some items might still be missing - just not triggered
with this specific config.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following build error:
drivers/built-in.o: In function `xc_load_fw_and_init_tuner':
xc5000.c:(.text+0x2dacd): undefined reference to `request_firmware'
xc5000.c:(.text+0x2daf0): undefined reference to `release_firmware'
xc5000.c:(.text+0x2db85): undefined reference to `release_firmware'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change addresses kernel bug #10459: In kernel 2.6.25 the
budget_av driver polls for an CI slot in 100ms intervals (because no
interrupt solution for budget_av cards is feasible due to HW reasons).
If no CI/CAM is connected to the DVB card, polling times out only after 250ms.
This periodic polling leads to high CPU load.
The change increases the polling interval for empty slots from 100ms to 5s.
Intervals for remaining slot states (invalid, in progress, ready) are unchanged,
as they are either temporary conditions or no timeout should occur.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx23885 driver used to use dvb-pll for LG-TDVS-H064F support on the
FusionHDTV5 Express. This has since been converted to use tuner-simple
instead, once digital tuning support was added to tuner-simple.
Since cx23885 no longer uses dvb-pll, remove the #include "dvb-pll.h",
and the DVB_PLL Kconfig selection.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver uses some sysfs helper functions that are available only for legacy
drivers. It also requires linux/mm.h.
This patch fixes compiliation when not in compat mode.
Thanks to Ingo Molnar for identifying this issue.
Acked-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Both mt9v022 and mt9m001 cameras are controlled over the I2C bus.
Respectively, their drivers require I2C to be built successfully.
Thanks to Ingo Molnar for reporting the build-breakage.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As pointed by Andrew Morton, the error testing were wrong. After reviewing
tea5767, it were returning a positive value for errors.
So, the double errors were cancelling each other.
This patch fix it properly. It also considers any positive value as ok, on
tuner-core.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Because it goes BUG.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update 3 more new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. These
video drivers aren't used yet so converting them is trivial.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix allmodconfig build bug introduced in latest -git by commit
7c91f0624a ("V4L/DVB(7767): Move tuners to common/tuners"):
LD kernel/built-in.o
LD drivers/built-in.o
ld: drivers/media/built-in.o: No such file: No such file or directory
which happens if all media drivers are modular:
http://redhat.com/~mingo/misc/config-Wed_Apr_30_09_24_48_CEST_2008.bad
In that case there's no obj-y rule connecting all the built-in.o files and
the link tree breaks.
The fix is to add a guaranteed obj-y rule for the core vmlinux to build.
(which results in an empty object file if all media drivers are modular)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/md/raid10.c:889:17: warning: Using plain integer as NULL pointer
drivers/media/video/cx18/cx18-driver.c:616:12: warning: Using plain integer as NULL pointer
sound/oss/kahlua.c:70:12: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some files in the drivers/media/video/saa7134 directory uses "int" for flags.
This can cause hard to find bugs on some architectures. This patch converts
the flags to use "long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86.git randconfig testing found a build failure on latest -git:
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x2a9a26): undefined reference to `tea5761_attach'
tuner-core.c:(.text+0x2a9d05): undefined reference to `tda9887_attach'
tuner-core.c:(.text+0x2a9d51): undefined reference to `xc2028_attach'
tuner-core.c:(.text+0x2a9e22): undefined reference to `tda829x_attach'
tuner-core.c:(.text+0x2a9e3f): undefined reference to `microtune_attach'
drivers/built-in.o: In function `tuner_probe':
tuner-core.c:(.text+0x2aa18a): undefined reference to `tda829x_probe'
tuner-core.c:(.text+0x2aa302): undefined reference to `tea5761_autodetection'
with the following config:
http://redhat.com/~mingo/misc/config-Wed_Apr_30_10_21_40_CEST_2008.bad
the problem is caused by the drivers/media/common/tuners/ subdirectory
not being part of the kbuild hierarchy anymore, due to commit
7c91f0624 ("V4L/DVB(7767): Move tuners to common/tuners").
this seems similar to the problem also reported by Mike Galbraith.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also, change the variable names used in the min/max macros to avoid shadowed
variable warnings when min/max min_t/max_t are nested.
Small formatting changes to make all the macros have a similar form.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix v4l build]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some Kconfig names were changed. This patch reapplies the rename script,
fixing for those drivers merged after the patch that renamed those
items.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (28 commits)
V4L-DVB(7789a): cx18: fix symbol conflict with ivtv driver
V4L/DVB (7789): tuner: remove static dependencies on analog tuner sub-modules
V4L/DVB (7785): [2.6 patch] make mt9{m001,v022}_controls[] static
V4L/DVB (7786): cx18: new driver for the Conexant CX23418 MPEG encoder chip
V4L/DVB (7783): drivers/media/dvb/frontends/s5h1420.c: printk fix
V4L/DVB (7782): pvrusb2: Driver is no longer experimental
V4L/DVB (7781): pvrusb2-dvb: include dvb support by default and update Kconfig help text
V4L/DVB (7780): pvrusb2: always enable support for OnAir Creator / HDTV USB2
V4L/DVB (7779): pvrusb2-dvb: quiet down noise in kernel log for feed debug
Rename common tuner Kconfig names to use the same
Fix V4L/DVB core help messages
V4L/DVB (7769): Move other terrestrial tuners to common/tuners
V4L/DVB (7768): reorganize some DVB-S Kconfig items
V4L/DVB(7767): Move tuners to common/tuners
V4L/DVB (7766): saa7134: add another PCI ID for Beholder M6
V4L/DVB (7765): Add support for Beholder BeholdTV H6
V4L/DVB (7763): ivtv: add tuner support for the AverMedia M116
V4L/DVB (7762): ivtv: fix tuner detection for PAL-N/Nc
V4L/DVB (7761): ivtv: increase the DMA timeout from 100 to 300 ms
V4L/DVB (7759): ivtv: increase version number to 1.2.1
...
LD drivers/media/video/built-in.o
drivers/media/video/cx18/built-in.o: In function `get_service_set':
/home/v4l/tokernel/git/drivers/media/video/cx18/cx18-ioctl.c:118: multiple definition of `get_service_set'
drivers/media/video/ivtv/built-in.o:/home/v4l/tokernel/git/drivers/media/video/ivtv/ivtv-ioctl.c:119: first defined here
drivers/media/video/cx18/built-in.o: In function `expand_service_set':
/home/v4l/tokernel/git/drivers/media/video/cx18/cx18-ioctl.c:92: multiple definition of `expand_service_set'
drivers/media/video/ivtv/built-in.o:/home/v4l/tokernel/git/drivers/media/video/ivtv/ivtv-ioctl.c:92: first defined here
drivers/media/video/cx18/built-in.o: In function `service2vbi':
/home/v4l/tokernel/git/drivers/media/video/cx18/cx18-ioctl.c:44: multiple definition of `service2vbi'
drivers/media/video/ivtv/built-in.o:/home/v4l/tokernel/git/drivers/media/video/ivtv/ivtv-ioctl.c:42: first defined here
make[2]: ** [drivers/media/video/built-in.o] Erro 1
make[1]: ** [drivers/media/video] Erro 2
make: ** [drivers/media/] Erro 2
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the needlessly global mt9{m001,v022}_controls[] static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Many thanks to Steve Toth from Hauppauge and Nattu Dakshinamurthy from
Conexant for their support. I am in particular thankful to Hauppauge
since without their help this driver would not exist. It should also
be noted that Steve did the work to get the DVB part up and running.
Thank you!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: G. Andrew Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/frontends/s5h1420.c: In function `s5h1420_setsymbolrate':
drivers/media/dvb/frontends/s5h1420.c:484: warning: long long unsigned int format, u64 arg (arg 2)
We do not know what type the architecture uses for u64.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver has been in-kernel and reasonably stable for well over a
year. It is in a stable form and is known to work well. Remove its
experimental status.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This was a build option in the past, to avoid conflicts with the cxusb module
for digital televsion support. Now that dtv mode support has been merged into
pvrusb2, the OnAir devices are fully supported by this single module. This no
longer should be a build option.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Get rid of the noise in dmesg during dvb feed changes,
unless the appropriate debug trace flag is enabled.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Those tuners are currently used only under media/dvb. However,
they can support also analog TV. Better to move them to the same place
as the other hybrid tuners. This would make easier to use those tuners also
by analog drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are some DVB-S tuners together with DVB-S tags, while
others together with tuners. Better to have all of them together.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.
Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When there is a lot of DMA traffic this timeout might sometimes be too low.
Increase it to be on the safe side.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Note that this card is only detected and not yet working.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner setup were happening during i2c attach callback. This means that it would
happen on two conditions:
1) if tuner module weren't load, it will happen at request_module("tuner");
2) if tuner is not compiled as a module, or it is already loaded
(for example, on setups with more than one tuner), it will happen
when saa7134 registers I2C bus.
Due to that, if tuner were loaded, tuner setup will happen _before_ reading
the proper values at tuner eeprom. Since set_addr refuses to change for a tuner
that were previously defined (except if the tuner_addr is set), this were
making eeprom tuner detection useless.
This patch removes tuner type setup from saa7134-i2c, moving it to the proper
place, after taking eeprom into account.
Reviewed-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner setup were happening during i2c attach callback. This means that it would
happen on two conditions:
1) if tuner module weren't load, it will happen at request_module("tuner");
2) if tuner is not compiled as a module, or it is already loaded
(for example, on setups with more than one tuner), it will happen
when cx88 registers I2C bus.
Due to that, if tuner were loaded, tuner setup will happen _before_ reading
the proper values at tuner eeprom. Since set_addr refuses to change for a tuner
that were previously defined (except if the tuner_addr is set), this were making
eeprom tuner detection useless.
This patch removes tuner type setup from cx88-i2c, moving it to the proper
place, after taking eeprom into account.
Reviewed-by: Gert Vervoort <gert.vervoort@hccnet.nl>
Reviewed-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/media/video/v4l2-common.c:719:16: warning: Using plain integer as NULL pointer
drivers/media/video/au0828/au0828-dvb.c:122:19: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1101:22: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1102:23: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-audio.c:78:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-video-v4l.c:84:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1264:9: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-context.c:197:28: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:126:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:133:32: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:145:31: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:177:55: warning: Using plain integer as NULL pointer
drivers/media/video/videobuf-core.c💯9: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing in the tree uses nopage any more. Remove support for it in the
core mm code and documentation (and a few stray references to it in
comments).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using i2c_transfer instead of i2c_master_recv in ir_probe saves a
temporary memory allocation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following cleanups and fixes:
- "debug" is definitely not a good name for a global variable,
renamed it to "au0828_debug"
this fixes a compile error with some kernel configurations
- since the module parameter is int the variable shouldn't be unsigned
- remove the {usb,bridge,i2c}_debug module parameters since they are
already covered by the "debug" module parameter
- remove the unused au0828_bcount
- make the needlessly global i2c_scan static
- make the needlessly global dvb_register() static
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
set_addr log were almost useless: discarded SET_TYPE_ADDR commands weren't
reported.
This patch changed set_addr printk to print a message only if set_addr is
wrong.
It also fix printk at set_type, since, if an attach were failing, nothing
were reported.
With the current code, working or not, a call to set_addr will produce a debug
printk.
also, set_type() were producing a false error message on tuner_xc2028, since
it were requesting for setting a frequency on a place where firmware name
weren't set yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Single-bit signed bitfields can only take 0/-1 rather than 0/1 as the
drivers seems to assume...add unsigned.
Noticed by sparse:
drivers/media/video/pvrusb2/pvrusb2-devattr.h:107:34: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:114:37: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:117:30: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:120:23: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:124:24: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:128:23: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:138:36: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:143:24: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:144:28: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:145:26: error: dubious one-bit signed bitfield
drivers/media/video/pvrusb2/pvrusb2-devattr.h:146:23: error: dubious one-bit signed bitfield
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds full support for this demodulator.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make it unsigned (0/1) rather than signed (0/-1).
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes a copy and paste error in check of kzalloc return value. The check block
was copied from the previous allocation but the variable wasn't exchanged.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
some gcc versions complain that fh is used without being defined.
The error report is bogus. However, fixing it is trivial. Better to make
gcc happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (452 commits)
V4L/DVB (7731): tuner-xc2028: fix signal strength calculus
V4L/DVB (7730): tuner-xc2028: Fix SCODE load for MTS firmwares
V4L/DVB (7729): Fix VIDIOCGAP corruption in ivtv
V4L/DVB (7728): tea5761: bugzilla #10462: tea5761 autodetection code were broken
V4L/DVB (7726): cx23885: Enable cx23417 support on the HVR1800
V4L/DVB (7725): cx23885: Add generic cx23417 hardware encoder support
V4L/DVB (7723): pvrusb2: Clean up input selection list generation in V4L interface
V4L/DVB (7722): pvrusb2: Implement FM radio support for Gotview USB2.0 DVD 2
V4L/DVB (7721): pvrusb2: Restructure cx23416 firmware loading to have a common exit point
V4L/DVB (7720): pvrusb2: Fix bad error code on cx23416 firmware load failure
V4L/DVB (7719): pvrusb2: Implement input selection enforcement
V4L/DVB (7718): pvrusb2-dvb: update Kbuild selections
V4L/DVB (7717): pvrusb2-dvb: add DVB-T support for Hauppauge pvrusb2 model 73xxx
V4L/DVB (7716): pvrusb2: clean up global functions
V4L/DVB (7715): pvrusb2: Clean out all use of __FUNCTION__
V4L/DVB (7714): pvrusb2: Fix hang on module removal
V4L/DVB (7713): pvrusb2: Implement cleaner DVB kernel thread shutdown
V4L/DVB (7712): pvrusb2: Close connect/disconnect race
V4L/DVB (7711): pvrusb2: Fix race on module unload
V4L/DVB (7710): pvrusb2: Implement critical digital streaming quirk for onair devices
...
There are different tables for MTS firmwares. This should be taken into
account while selecting the proper firmware.
While at tuner-xc2028.h, improve some comments.
Thanks to Edward J. Sheldrake <ejs1920@yahoo.co.uk> for helping to
diagnose such troubles with PAL/I standard.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frank Bennett reported that ivtv was causing skype to crash. With help
from one of their developers he showed it was a kernel problem.
VIDIOCGCAP copies a name into a fixed length buffer - ivtv uses names
that are too long and does not truncate them so corrupts a few bytes of
the app data area.
Possibly the names also want trimming but for now this should fix the
corruption case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx23885: Enable cx23417 support on the HVR1800
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change how list of possible pvrusb2 inputs is generated to include
only those interfaces that make sense for the interface instance.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These changes are required with the addition of digital television support
for the Hauppauge HVR1900 & HVR1950, the OnAir Creator and Sasem USB HDTV
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following cleanups:
- make the following needlessly global function static:
- pvr2_hdw_set_cur_freq()
- #if 0 the following unused global functions:
- pvr2_hdw_get_state_name()
- pvr2_hdw_get_debug_info_unlocked()
- pvr2_hdw_get_debug_info_locked()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently the kernel developers no longer consider it proper
etiquette to use __FUNCTION__; everyone must instead use __func__
(even though it breaks with older compilers). And worse still, actual
effort is being expended to sweep this change throughout the kernel
source tree. Don't these people have better things to do? So...
Completely clean out all use of __FUNCTION__ from the pvrusb2 driver
(it was just in the sysfs interface). I'm not going to use __func__
either. So there.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver was getting had by this scenario:
1. Task A calls kthread_stop() for task B.
2. Before exiting, then Task B calls kthread_stop() for task C.
The problem is, kthread_stop() wants to allocate an internal resource
to itself (i.e. acquire a lock), which won't be released until
kthread_stop() returns. But kthread_stop() won't return until task B
is dead. But task B won't die until it finishes its call to
kthread_stop() for task C, and that will block waiting on the resource
already allocated inside task A. Deadlock.
With the pvrusb2 driver, task A is the caller to pvr_exit(), task B is
the control thread run inside of pvrusb2-context.c, and task C is any
worker thread run inside of pvrusb2-hdw.c.
This problem got introduced by the previous threading setup change,
which was itself an attempt to fix a module tear-down race (which it
actually did fix). The lesson here is that a task being waited on as
part of a kthread_stop() simply cannot be allow to also issue a
kthread_stop() - or we make sure not to issue the enclosing
kthread_stop() until we know that the inner kthread_stop() has
completed first. The solution for the pvrusb2 driver is some hackish
code which changes the main control thread tear down into a two step
process. This then makes it possible to delay issuing the
kthread_stop() on the control thread until after we know that
everything has been torn down first. (And yes, we really need that
kthread_stop() because it's the only way to safely guarantee that a
module-referencing kernel thread has safely returned back out of the
module before we finally remove the module.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Earlier fix to handle DVB feed thread aborts was overly-aggressive.
We can take better advantage of what kthread_stop() can do. This
change simplifies things.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If a disconnect happens before initialization is completed, the
pvrusb2 driver can accidentally touch dangling pointers. The whole
initialization function must be protected by the big_lock, and once
inside that lock, the initialization function should abort if it is
discovered that a disconnect has already taken place.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver - for basically forever - was not enforcing a
proper module tear-down. Kernel threads are used inside the driver
and all must be gone before the module can be safely removed. This
changeset reimplements a chunk of pvrusb2-context.c to enforce this
correctly. Unfortunately this is not a simple fix. The new
implementation also cuts back on kernel thread usage; instead of there
being 1 control thread per instance now it's just 1 control thread
shared by all instances. (By dropping to a single thread then the
module exit function can block on its shutdown and the thread itself
can monitor and cleanly shut down all of the other instances first.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
David Woodhouse