It's not needed any more since device always operates in interrupt-driven mode
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
Display the current media type connected to the port in ethtool.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to the bnx2x for retrieving dcb peer (remote)
configuration from the embedded DCBX stack.
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid link notification duplication
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ndo_fix_features callback is postponing features change when
bp->recovery_state != BNX2X_RECOVERY_DONE, netdev_update_features()
has to be called again when this condition changes. Previously,
ethtool_ops->set_flags callback returned -EBUSY in that case
(it's not possible in the new model).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
v5: - don't delay set_features, as it's rtnl_locked - same as recovery process
v4: - complete bp->rx_csum -> NETIF_F_RXCSUM conversion
- add check for failed ndo_set_features in ndo_open callback
v3: - include NETIF_F_LRO in hw_features
- don't call netdev_update_features() if bnx2x_nic_load() failed
v2: - comment in ndo_fix_features callback
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase resolution of MaxBW algorithm to suit
Min Bandwidth configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing speed setting in NPAR requires HW access, this patch
delays the access to D0 state when performed in D3.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the bnx2x uses the generic dcbnl application tlv list
instead of implementing its own get-app handler. When the driver is
alerted to a change in the DCB negotiated parameters, it calls
dcb_setapp to update the dcbnl application tlvs list making it available
to user mode applications and registered notifiers.
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support fetching and retrieving RX indirection table via ethtool.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completed the bnx2x_set_rx_mode() to a proper netdev->ndo_set_rx_mode
implementation:
- Added a missing configuration of a unicast MAC addresses list.
- Changed bp->dma_lock from being a mutex to a spinlock as long as it's taken
under netdev->addr_list_lock now.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always configure an FCoE L2 ring with a mini-jumbo MTU size (2500).
To do that we had to move the rx_buf_size parameter from per
function level to a per ring level.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all shared mem code to bnx2x to avoid code duplication. bnx2x now
performs:
- Read the FCoE and iSCSI max connection information.
- Read the iSCSI and FCoE MACs from NPAR configuration in shmem.
- Block the CNIC for the current function if there is neither FCoE nor
iSCSI valid configuration by returning NULL from bnx2x_cnic_probe().
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version to 1.62.11-0
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version to 1.62.00-5
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing __rcu annotations and helpers.
minor : Fix some rcu_dereference() calls in macvtap
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
Update bnx2x version to 1.62.00-4
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes in registers dump:
- Properly calculate dump length for 57712.
- Prevent HW blocks parity attentions when dumping registers in order to
prevent false parity errors handling.
- Update the bnx2x_dump.h file: old one had a few bugs that could cause
fatal HW error as a result of a registers dump.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding dcbnl implementation to bnx2x allowing users to manage the
embedded DCBX engine.
This patch is dependent on the following patches:
[net-next-2.6 PATCH 1/3] dcbnl: add support for ieee8021Qaz attributes
[net-next-2.6 PATCH 2/3] dcbnl: add appliction tlv handlers
[net-next-2.6 PATCH 3/3] net_dcb: add application notifiers
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding DCB initialization and handling on 57712 FW/HW
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Includes new driver structures and FW/HW configuration for FCoE ring
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC partitioning is another flavor of multi function - having few
PCI functions share the same physical port. Unlike the currently
supported mode of multi-function which depends on the switch
configuration and uses outer-VLAN, the NPAR mode is switch independent
and uses the MAC addresses to distribute incoming packets to the different
functions. This patch adds the specific HW setting of the NPAR mode
and some distinctions between switch dependent (SD) and
switch independent (SI) multi-function (MF) modes where the configuration
is not the same.
Advance driver version to 1.60.00-6
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the interrupt mode configuration and NAPIs adding before a
register_netdev() call to prevent netdev->open() from running
before these functions are done.
Advance a driver version number.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reported-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version number.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make many functions that are only used in one file static.
Remove dead code for override_led_value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the bnx2x driver use the new vlan accleration model.
Signed-off-by: Hao Zheng <hzheng@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by: Joe Perches <joe@perches.com>
Although RSS is meaningless when there is a single HW queue we
still need it enabled in order to have HW Rx hash generated.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not include any functional changes.
The changes are: empty lines, indentation and comments.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decide which interrupt mode to use (MSI-X, MSI, INTa) only once in probe() and
initialize appropriate structures.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
57712 HW supported with same set of features as for 57710/57711
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field is now accessed from different contexts.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
