The function omap3_save_secure_ram() is now called only once during
the initialization of the device and consequent sleep cycles will
re-use the same saved contents for secure RAM. Users who need secure
services should do secure RAM saving before entering off-mode, if a
secure service has been accessed after last save.
There are both latency and reliability issues with saving secure RAM
context in the idle path. The context save uses a hardware resource
which takes an order of hundreds of milliseconds to initialize after a
wake up from off-mode, and also there is no way of checking whether it
is ready from kernel side or not. It just crashes if you use it too
quickly
Additional fix to ensure scratchpad save is done after secure
RAM by Roger Quadros.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For HS/EMU devices, some additional resources need to be
saved/restored for off-mode support. Namely, saving the secure RAM
and a pointer to it in the scratchpad.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For HS/EMU devices, these additional features are also used:
- DMA interrupt disable routine added
- Added DMA controller reset to DMA context restore
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for CORE powerdomain resources in order
to support off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds a 'save_state' option when calling into SRAM idle function
and adds some minor cleanups of SRAM asm code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
During the MMU restoration on the restore path from MPU OFF, the page
table entry for the page consisting of the code being executed is
modified to make MMU return VA=PA.
The MMU is then enabled and the original entry is being stored in
scratchpad. This patch reads the original values stored in
scratchpad, and restores them back.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Expand the powerdomains handled in the idle path to include PER, NEON
and CORE. This includes properly clearing the previous powerstates,
linking NEON state to MPU state and calling the UART prepare functions
for only the appropraite powerdomain transitions (CORE for UART1,2,
PER for UART3.)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Generalize the copy of SRAM functions into omap_push_sram_idle()
so it can be used on init but also after off-mode transitions.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for the System Control Module to suport
off-mode.
ETK and debobs definitions added by Peter De Schrijver.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch populates the scratchpad contents as expected by the
bootROM code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for PRCM module to support off-mode.
Additional registers (CM_CLKSEL4, CM_CLKEN, CM_CLKEN2) added by Tero
Kristo.
Missing CM_CLKEN_PLL_IVA2 register added by Kalle Jokiniemi.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for the INTC module to support off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore to enable off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the context save and restore functions for GPMC to
enable off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'for-linus' of git://github.com/at91linux/linux-2.6-at91:
at91: at91sam9g45 family: identify several chip versions
avr32: add two new at91 to cpu.h definition
cpu_is_xxx() macros are identifying generic at91sam9g45 chip. This patch adds
the capacity to differentiate Engineering Samples and final lots through the
inclusion of at91_cpu_fully_identify() and the related chip IDs with chip
version field preserved.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Somme common drivers will need those at91 cpu_is_xxx() definitions. As
at91sam9g10 and at91sam9g45 are on the way to linus' tree, here is the patch
that adds those chips to cpu.h in AVR32 architecture.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (38 commits)
MIPS: O32: Fix ppoll
MIPS: Oprofile: Rename cpu_type from godson2 to loongson2
MIPS: Alchemy: Fix hang with high-frequency edge interrupts
MIPS: TXx9: Fix spi-baseclk value
MIPS: bcm63xx: Set the correct BCM3302 CPU name
MIPS: Loongson 2: Set cpu_has_dc_aliases and cpu_icache_snoops_remote_store
MIPS: Avoid potential hazard on Context register
MIPS: Octeon: Use lockless interrupt controller operations when possible.
MIPS: Octeon: Use write_{un,}lock_irq{restore,save} to set irq affinity
MIPS: Set S-cache linesize to 64-bytes for MTI's S-cache
MIPS: SMTC: Avoid queing multiple reschedule IPIs
MIPS: GCMP: Avoid accessing registers when they are not present
MIPS: GIC: Random fixes and enhancements.
MIPS: CMP: Fix memory barriers for correct operation of amon_cpu_start
MIPS: Fix abs.[sd] and neg.[sd] emulation for NaN operands
MIPS: SPRAM: Clean up support code a little
MIPS: 1004K: Enable SPRAM support.
MIPS: Malta: Enable PCI 2.1 compatibility in PIIX4
MIPS: Kconfig: Fix duplicate default value for MIPS_L1_CACHE_SHIFT.
MIPS: MTI: Fix accesses to device registers on MIPS boards
...
* 'fixes-s3c-2632-rc5' of git://git.fluff.org/bjdooks/linux:
ARM: S3C2410: Fix sparse warnings in arch/arm/mach-s3c2410/gpio.c
ARM: S3C2440: mini2440: Fix spare warnings
ARM: S3C24XX: Fix warnings in arch/arm/plat-s3c24xx/gpio.c
ARM: S3C2440: mini2440: Fix missing CONFIG_S3C_DEV_USB_HOST
ARM: S3C24XX: arch/arm/plat-s3c24xx: Move dereference after NULL test
ARM: S3C: Fix adc function exports
ARM: S3C2410: Fix link if CONFIG_S3C2410_IOTIMING is not set
ARM: S3C24XX: Introduce S3C2442B CPU
ARM: S3C24XX: Define a macro to avoid compilation error
ARM: S3C: Add info for supporting circular DMA buffers
ARM: S3C64XX: Set rate of crystal mux
ARM: S3C64XX: Fix S3C64XX_CLKDIV0_ARM_MASK value
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
Revert "[IA64] fix percpu warnings"
[IA64] fix percpu warnings
[IA64] SMT friendly version of spin_unlock_wait()
[IA64] use printk_once() unaligned.c/io_common.c
[IA64] Require SAL 3.2 in order to do extended config space ops
[IA64] unsigned cannot be less than 0 in sn_hwperf_ioctl()
[IA64] Restore registers in the stack on INIT
[IA64] Re-implement spinaphores using ticket lock concepts
[IA64] Squeeze ticket locks back into 4 bytes.
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: ensure initial page tables are setup for SMP systems
ARM: 5776/1: Check compiler version and EABI support when adding ARM unwind support.
ARM: 5774/1: Fix Realview ARM1176PB board reboot
ARM: Fix errata 411920 workarounds
ARM: Fix sparsemem with SPARSEMEM_EXTREME enabled
ARM: Use GFP_DMA only for masks _less_ than 32-bit
ARM: integrator: allow Integrator to be built with highmem
ARM: Fix signal restart issues with NX and OABI compat
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Make EFI RTC function depend on 32bit again
x86-64: Fix register leak in 32-bit syscall audting
x86: crash_dump: Fix non-pae kdump kernel memory accesses
x86: Side-step lguest problem by only building cmpxchg8b_emu for pre-Pentium
x86: Remove STACKPROTECTOR_ALL
This reverts commit b94b08081f.
genksyms currently cannot handle complicated types for exported
percpu variables. Drop this patch for now as it prevents a
module from being loaded on sn2 systems:
xpc: no symbol version for per_cpu____sn_cnodeid_to_nasid
xpc: Unknown symbol per_cpu____sn_cnodeid_to_nasid
Signed-off-by: Tony Luck <tony.luck@intel.com>
Mapping the same memory using two different attributes (memory
type, shareability, cacheability) is unpredictable. During boot,
we encounter a situation when we're updating the kernel's page
tables which can lead to dirty cache lines existing in the cache
which are subsequently missed. This causes stack corruption,
and therefore a crash.
Therefore, ensure that the shared and cacheability settings
matches the configuration that will be used later; this together
with the restriction in early_cachepolicy() ensures that we won't
create a mismatch during boot.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM unwind is known to compile only with EABI and not-buggy compilers.
The problem is not the unwinding information but the -fno-frame-pointer
option added as a result of !CONFIG_FRAME_POINTER. Now we check the
compiler and raise a #warning in case of wrong compiler.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sys_ppoll syscall needs to use a compat handler on 64bit kernels with o32
user-space.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unify the naming method between kernel and the user-space oprofile tool.
Because loongson is used instead of godson in most of the places, we agreed
to use loongson instead, which will simplify future maintenance.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The handle_edge_irq() flowhandler disables edge int sources which occur
too fast (i.e. another edge comes in before the irq handler function
had a chance to finish). Currently, the mask_ack() callback does not
ack the edges in hardware, leading to an endless loop in the flowhandler
where it tries to shut up the irq source.
When I rewrote the alchemy IRQ code I wrongly assumed the mask_ack()
callback was only used by the level flowhandler, hence it omitted the
(at the time pointless) edge acks. Turned out I was wrong; so here
is a complete mask_ack implementation for Alchemy IC, which fixes
the above mentioned problem.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For consistency with other BCM63xx SoC set the CPU name to "Broadcom
BCM6338" when actually running on that system.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson 2 does not have dcache aliases when is using 16k pages. and the
And because Loongson 2 doesn't do SMP , cpu_icache_snoops_remote_store does
not matter here.
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
set_saved_sp reads Context register. Avoid reading stale value from
earlier incomplete write.
Issue found and fixed for head.S by Chris Dearman <chris@mips.com>.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some newer Octeon chips have registers that allow lockless operation of
the interrupt controller. Take advantage of them.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the locks are used from interrupt context we need the
irqsave/irqrestore versions of the locking functions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch ensures that the sign bit is always updated for NaN operands.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes the remaining problems introduced by
f197465384 (incorrect access length &
byteswapping in bigendian mode)
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On an SMP system with cache aliases, the following sequence of events may
happen:
1) copy_user_highpage() runs on CPU0, invoking kmap_coherent() to create a
temporary mapping in the fixmap region
2) copy_page() starts on CPU0
3) CPU1 sends CPU0 an IPI asking CPU0 to run local_r4k_flush_cache_page()
4) CPU0 takes the interrupt, interrupting copy_page()
5) local_r4k_flush_cache_page() on CPU0 calls kmap_coherent() again
6) The second invocation of kmap_coherent() on CPU0 tries to use the
same fixmap virtual address that was being used by copy_user_highpage()
7) CPU0 throws a machine check exception for the TLB address conflict
Fixed by creating an extra set of fixmap entries for use in interrupt
handlers. This prevents fixmap VA conflicts between copy_user_highpage()
running in user context, and local_r4k_flush_cache_page() invoked from an
SMP IPI.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch checks if the watchdog enable bit is set in the DCL register
meaning that the hardware watchdog actually works and if so, register the
ar7_wdt platform_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch prepares the board code to register a bcm63xx_wdt
platform_device that we are going to use in a subsequent patch.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tero Kristo