The problem is introduced by commit
664d080c41.
acpi_evaluate_integer is a sleeping function,
and it should not be called with spin_lock_irqsave.
https://bugzilla.redhat.com/show_bug.cgi?id=451399
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some BIOSen enable DIPM via _GTF which causes command timeouts under
certain configuration. This didn't occur on 2.6.25 because 2.6.25
defaulted to SRST, so _GTF wasn't executed during boot probe, so ahci
host reset disabled DIPM and as _GTF wasn't executed after SRST, DIPM
wasn't enabled. On 2.6.26, hardreset is used during probe and after
probe _GTF is executed enabling DIPM and thus the failures.
This patch could theoretically disable DIPM on machines which used to
have it enabled on 2.6.25 but AFAIK ahci is currently the only driver
which uses SATA ACPI hierarchy (_SDD) and as the host reset would have
always disabled DIPM, this shouldn't happen.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit ea0c62f7cf tried to clear all
bits in irq_stat but it didn't actually achieve that as irq_stat was
anded with port_map right after read. This patch makes ahci driver
always use the unmasked value to clear irq_status.
While at it, add explanation on the peculiarities of ahci IRQ
clearing.
This was spotted by Linus Torvalds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a miniscule chance that two separate host controllers
might be in sata_mv at the same time and manage to decrement
the static limit_warnings variable below zero.
Fix the comparison to deal with it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Improve SFF HSM violation reporting such that each HSM violation can
be distinguished using ehi_desc.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some AHCI controllers (ICH7 was reported) set pending bit in
HOST_IRQ_STAT for non-existent ports and when it's not cleared falls
into IRQ storm. Always clear full irq_stat instead of only the bits
that are handled. As nothing changes for recognized ports, the risk
of breaking things is pretty low.
Reported and verified by Philipp Thomas in the following suse
bugzilla.
https://bugzilla.novell.com/attachment.cgi?id=215692
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Thomas <pth@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's another DID used for Adaptec card. Add it.
Reported by Travis Read.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Travis Read <ics@dark.net.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds blk_queue_update_dma_pad to prevent LLDs from overwriting
the dma pad mask wrongly (we added blk_queue_update_dma_alignment due
to the same reason).
This also converts libata to use blk_queue_update_dma_pad instead of
blk_queue_dma_pad.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sata_uli can't do hardresets reliably and lock up. This went
unnoticed till now as softreset was the default and hardreset was only
used after softreset failed.
Reported by Christian Casteyde in bz#10860.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
BAST: Remove old IDE driver
pcmcia ide kingston compactflash's have a new manufacturer id
pcmcia: add another pata/ide ID
pcmcia: add an pata/ide ID
ide: increase timeout in wait_drive_not_busy()
palm_bk3710: fix resource management
Addition of Transcend 1GB 45x id so that it is properly detected.
[bart: fix typo in ide-cs's ID spotted by Alan Cox]
Signed-off-by: William Peters <w1ll14@gmail.com>
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
From: Piter PUNK <piterpunk@slackware.com>
SiS AHCIs say they can do PMP but can't and fail detection if SRST w/
pmp==15 is used. Turn off PMP support.
tj: added patch description, adapted patch to #upstream-fixes and
renamed board_ahci_sis to board_ahci_nopmp.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
TOSHIBA also used "TECRA M4" in additon to "Tecra M4", add it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add HAVE_PATA_PLATFORM to select the pata platform driver
to ensure that we do not end up with a long 'depends on' list
when other users of this driver turn up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Chip errata sometimes prevents reliable use of PIO commands which involve
more than a single DRQ (data request). In normal operation, libata should
not generate such PIO commands (uses DMA instead), but they could be sent
in via SG_IO from userspace.
A full workaround might be to break up such commands into sequences
of single DRQ ones, but that's just way too complex for something
that doesn't normally happen in real life.
So, allow the attempt (it often works, despite the errata),
but log the event for reference when somebody screams.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The early chipsets cannot safely handle Async Notification (AN),
but 6041/6081 chip revision "C0" (and newer) can handle it.
So allow AN for "C0" and higher.
This enables use of hotplug on PMP ports for the 6041/6081 PCI Rev.9 chips.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no reason to check whether to use DMA or not for no data
commands. Don't do it. While at it, make local variable using_pio in
atapi_xlat() set iff ATAPI_PROT_PIO is going to be used and rename
ata_check_atapi_dma() to atapi_check_dma() for consistency.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
JMB361 has only one port but reports it has two causing longish probe
failure on the second one. Quirk it.
Reported by Gajo Petrovic in bz 10911.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Gajo Petrovic <gajo01@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads
to soft reset failure. This patch can fix the bug.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering:
fixlet to a57c1bade5 libata-sff:
Fix oops reported in kerneloops.org for pnp devices with no ctl
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it
Add
ata_sff_irq_status - encapsulates the IRQ check logic
This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that
ata_sff_sync - ensure writes hit the device
Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.
- ata_sff_pause - 400nS delay
Ensure the command hit the device and delay 400nS
- ata_sff_dma_pause
Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)
The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The handling for PHY_MODE4 was originally just cloned from the
Marvell proprietary driver (with their blessing).
But we can do better than that.
Tidy things up with some judicious mask definitions, to improve maintainability.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ICH6 on ACER Aspire 1694WLMi to list of laptops that use short cables
rather than 80 wire
OriginalAuthor: Tiago Sousa
OriginalLocation: http://launchpadlibrarian.net/11627664/new.ich_laptop.short.cables.diff
Bug: #187121
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Differentiate between bay devices in dock stations and others:
- When an ACPI_NOTIFY_EJECT_REQUEST appears, just signal uevent to
userspace (that is when the optional eject button on a bay device is
pressed/pulled) giving the possibility to unmount file systems and to
clean up. Also, only send uevent in case we get an EJECT_REQUEST
without doing anything else. In other cases, you'll get an add/remove
event because libata attaches/detaches the device.
- In case of a dock event, which in turn signals an
ACPI_NOTIFY_EJECT_REQUEST, immediately detach the device, because it
may already have been gone
* In case of an ACPI_NOTIFY_DEVICE/BUS_CHECK, evaluate _STA to check if
the device has been plugged or unplugged. If plugged, hotplug it, if
unplugged, just signal event to userspace
(initial patch by Matthew Garrett <mjg59@srcf.ucam.org>)
* Call ACPI _EJ0 for detached devices
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change the partial Device IDs of nvidia MCP7B AHCI controller in ahci.c,
as the actual PCI IDs deployed in the field differed from the forecasted ones
preemptively placed in the driver.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following commit (4c9bf4e799):
libata: replace tf_read with qc_fill_rtf for non-SFF drivers
Broke the sata_fsl.c driver in 2.6.26-rc. I know the following patch fixes
the issue, it clearly also adds port multipler support. The current
2.6.26-rc driver is broken.
On boot with debug enabled we get something like (w/o this patch):
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
spurious interrupt!!, CC = 0x1
interrupt status 0x1
xx_scr_read, reg_in = 1
.. continues for ever.
This change fixes this as a side effect of adding port multiplier support.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As in sil4726, SRST can't be trusted on sil3726 causing detection
problems under certain configuraitons. I thought it was from the
Config Disk device but apparently not.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix libata-scsi kernel-doc notation:
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1659): No description found for parameter 'cmd'
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1971): No description found for parameter 'buf'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ICH8M on macbooks are peculiar in that some of them lock up when the
second port is enabled, some return bogus values on SIDPR access while
yet others hang on SIDPR access. Also, the ich8m_apple_sata entry was
wrongly added below generic ich8m entry making it virtually useless.
This patch works around macbook ich8m problems by
* moving ich8m_apple_sata entry above generic ich8m entry
* dropping PIIX_FLAG_SIDPR from ich8m_apple_sata
* adding subsystem 106b:00a1 as ich8m_apple_sata
Reported and tested by MATSUBAYASHI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: MATSUBAYASHI 'Shaolin' Kohji <shaolin@rhythmaning.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 5182 System-On-Chip (SOC) variant wants certain lower
bits to be cleared on any write to the PHY_MODE3 register.
If/when support is added for other SOC variants, we'll need
some way to uniquely identify the 5182, and not perform this
workaround for the others.
But for now, it is the only SOC variant we support here.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The "B2" variant of the 6041/6081 (genII) chips requires
that the PHY_MODE3 register be rewritten after any write
to PHY_MODE4.
This fixes a regression introduced by an earlier patch.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The only public release of the 6042/7042 chips was/is revision "B0".
Remove code that attempted to deal with earlier, non-released revs.
This matches the logic of the current Marvell "proprietary" driver.
Also, bump up the sata_mv version number, to reflect this batch of erratas.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix and update the errata handling for the PHY_MODEx registers.
This improves receiver noise tolerance, among other things.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert the System-on-Chip flag from a host flag to an hpriv flag,
for better consistency with other chip-rev flags, and for easier use
in errata fixes etc.
Also change the related "HAS_PCI()" into "!IS_SOC()" for better consistency
of naming/use (everything else SOC-related already uses "SOC").
There are no functionality changes in this patch.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The libata-acpi.c code currently accepts hotplug messages from both the
port and the device. This does not match the behaviour of the bay
driver, and may result in confusion when two hotplug requests are
received for the same device. This patch limits the hotplug notification
to removable ACPI devices, which in turn allows it to use the _STA
method to determine whether the device has been removed or inserted.
On removal, devices are marked as detached. On insertion, a hotplug scan
is started. This should avoid lockups caused by the ata layer attempting
to scan devices which have been removed. The uevent sending is moved
outside the spinlock in order to avoid a warning generated by it firing
when interrupts are disabled.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I was hoping ATA_HORKAGE_NODMA | ATA_HORKAGE_SKIP_PM could keep it
happy but no even this doesn't work under certain configurations and
it's not like we can do anything useful with the cofig device anyway.
Replace ATA_HORKAGE_SKIP_PM with ATA_HORKAGE_DISABLE and use it for
the config device. This makes the device completely ignored by
libata.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When 4140 PMP is attached to sil24, NCQ commands to fan out port 1 and
2 (0 based) often stall if commands are in progress to other ports.
I've tried a number of things but can't tell what's going on. It
never happens w/ ahci and reportedly sata_mv which can issue NCQ
commands to multiple devices simultaneously like sil24 does.
Disable NCQ for devices behind 4140 PMP for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no reason to schedule LPM action after probing is complete
causing another EH iteration. Just schedule it together with probing
itself.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PMP notification during reset can make some controllers fail reset
processing and needs to be turned off during resets. PMP attach and
full-revalidation path did this via sata_pmp_configure() but the quick
revalidation wasn't. Move the notification disable code right above
fan-out port recovery so that it's always turned off.
This fixes obscure reset failures.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This timeout was set low because previously PMP register access was
done via polling and register access timeouts could stack up. This is
no longer the case. One timeout will make all following accesses fail
immediately.
In rare cases both marvell and SIMG PMPs need almost a second. Bump
it to 3s.
While at it, rename it to SATA_PMP_RW_TIMEOUT. It's not specific to
SCR access.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
No reason to get overzealous about recovered comm and data errors.
Some PHYs habitually sets them w/o no good reason and being draconian
about these soft error conditions doesn't seem to help anybody.
If need ever rises, we might need to add soft PHY error condition, say
AC_ERR_MAYBE_ATA_BUS and use it only to determine whether speed down
is necessary but I don't think that's very likely to happen. It's far
more likely we'll get timeouts or fatal transmission errors if
recovered errors are so prominent that they hamper operation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Originally, whole reset processing was done while the port is frozen
and SError was cleared during @postreset(). This had two race
conditions. 1: hotplug could occur after reset but before SError is
cleared and libata won't know about it. 2: hotplug could occur after
all the reset is complete but before the port is thawed. As all
events are cleared on thaw, the hotplug event would be lost.
Commit ac371987a8 kills the first race
by clearing SError during link resume but before link onlineness test.
However, this doesn't fix race #2 and in some cases clearing SError
after SRST is a good idea.
This patch solves this problem by cross checking link onlineness with
classification result after SError is cleared and port is thawed.
Reset is retried if link is online but all devices attached to the
link are unknown. As all devices will be revalidated, this one-way
check is enough to ensure that all devices are detected and
revalidated reliably.
This, luckily, also fixes the cases where host controller returns
bogus status while harddrive is spinning up after hotplug making
classification run before the device sends the first FIS and thus
causes misdetection.
Low level drivers can bypass the logic by setting class explicitly to
ATA_DEV_NONE if ever necessary (currently none requires this).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Previously reset freeze/thaw handling lived outside of ata_eh_reset()
mainly because the original PMP reset code needed the port frozen
while resetting all the fan-out ports, which is no longer the case.
This patch moves freeze/thaw handling into ata_eh_reset().
@prereset() and @postreset() are now called w/o freezing the port
although @prereset() an be called frozen if the port is frozen prior
to entering ata_eh_reset().
This makes code simpler and will help removing hotplug event related
races.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reorganize ata_eh_reset() such that @prereset() is called even when no
reset method is available and if block is used instead of goto to skip
actual reset. This makes no reset case behave better (readiness wait)
and future changes easier.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The @online out parameter is supposed to set to true iff link is
online and reset succeeded as advertised in the function description
and callers are coded expecting that. However, sata_link_reset()
didn't behave this way on device readiness test failure. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Minor coding-style fixes for sata_promise:
- remove stray blank lines
- fix checkpatch.pl errors; warnings about long lines
remain, but I don't intend to address those at this time
- remove two inline directives: neither is essential and
both functions are trivially inlinable anyway by virtue
of being static and having a single unique call site
- fix comment in pdc_interrupt(): the bits in PDC_INT_SEQMASK
denote SEQIDs not tags, the distinction becomes important
when NCQ gets implemented
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch cleans up sata_promise's mmio accesses.
In sata_promise there are three distinct mmio address spaces:
1. global registers, offsets from host->iomap[PDC_MMIO_BAR]
2. per-port ATA registers, offsets from ap->ioaddr.cmd_addr
3. per-port SATA registers, offsets from ap->ioaddr.scr_addr
The driver currently often fails to indicate which address space
a given mmio base pointer refers to, which is a source of bugs
and confusion (see recent pdc_thaw() irq clearing bug; it's also
been an obstacle for the pending NCQ extensions).
To reduce these problems, adopt a coding style where the name of
a base pointer always indicates which address space it refers to:
1. global registers: host_mmio
2. per-port ATA registers: ata_mmio
3. per-port SATA registers: sata_mmio
Also rearrange register offset definitions to clearly indicate
which address space they belong to, and add a symbolic definition
for the previously hard-coded PHYMODE4 register.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes two bugs in sata_promise's irq status clearing paths:
1. When clearing the irq status for a specific port, the driver
read the global SEQMASK register. This is wrong because that
clears the irq status for _all_ ports.
2. pdc_thaw() incorrectly added the PDC_INT_SEQMASK host register
offset to a per-port ata engine base address. This resulted in
it reading the unrelated PDC_PKT_SUBMIT register, which did not
have the desired irq status clearing effect.
In both cases the fix is to read from the port's Command/Status
register. This also matches what Promise's own driver does.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use the kernel-provided clamp_val() macro.
FIT was always applied to a member of struct ata_timing (unsigned short)
and two constants. clamp_val will not cast to short anymore.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Check for an empty request queue before stopping EDMA after a FBS-NCQ error,
as per recommendation from the Marvell datasheet.
This ensures that the EDMA won't suddenly become active again
just after our subsequent check of the empty/idle bits.
Also bump DRV_VERSION.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part five of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Keep a cached copy of the main_irq_mask so that we don't have
to stall the CPU to read it on every pass through mv_interrupt.
This significantly speeds up interrupt handling, both for sata_mv,
and for any other driver/device sharing the same PCI IRQ line.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part four of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Ignore masked IRQs in mv_interrupt().
This prevents "unexpected device interrupt while idle" messages.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part three of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Partially fix a reported bug whereby we sometimes miss seeing drives on
a port-multiplier, as reported by Gwendal Grignou <gwendal@google.com>.
The problem was that we were receiving unexpected interrupts
during EH from POLLed commands while accessing port-multiplier registers.
These unexpected interrupts can be prevented by masking the DONE_IRQ bit
for the port whenever not operating in EDMA mode.
Also fix port_stop() to mask all port interrupts.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part two of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Consolidate all updates of the host main_irq_mask register
into a single function. This simplifies maintenance,
and also prepares the way for caching it (later).
No functionality changes in this update.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part one of simplifying/fixing handling of the main_irq_mask register
to resolve unexpected interrupt issues observed in 2.6.26-rc*.
Don't blindly enable port IRQs at host init time.
Instead, enable only the bits that we want,
which in this case is simply the PCI_ERR bit.
The per-port bits can wait until the ports are reset/probed for devices.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that we handle the FIS_IRQ_CAUSE register correctly,
we can also now handle SATA asynchronous notification events.
So enable them, but only for the more modern GenIIe chips.
(older chips have unaddressed errata issues related to this).
This fixes hot plug/unplug for port-muliplier ports.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Group all of the flags for GenIIe devices into a common definition,
to ensure that any updates to them are shared by all GenIIe devices.
This will help make future maintenance somewhat simpler.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix handling of the FIS_IRQ_CAUSE register in sata_mv.
This register exists *only* on GenIIe devices, so don't bother
writing to it on older chips. Also, it has to be read/cleared
in mv_err_intr() before clearing the main ERR_IRQ_CAUSE register.
This keeps sata_mv from getting stuck forever on certain error types.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Always request a softreset after hardreset succeeds.
This fixes a regression reported by Martin Michlmayr <tbm@cyrius.com>.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set ATAPI host state machine to control IDE device terminate sequence.
Some IDE harddisk may assert terminate sequence in the middle of a
formal DMA transaction and resume later. Bit DETECT_TERM in ATAPI_CTRL
register determines whether the ATAPI host state machine or the kernel
driver should take care of this case.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A couple of distributions (Fedora, Ubuntu) were having weird problems with the
ATI IXP series PATA controllers being reported as simplex. At the heart of
the problem is that both distros ignored the recommendations to load pata_acpi
and ata_generic *AFTER* specific host drivers.
The underlying cause however is that if you D3 and then D0 an ATI IXP it
helpfully throws away some configuration and won't let you rewrite it.
Add checks to ata_generic and pata_acpi to pin ATIIXP devices. Possibly the
real answer here is to quirk them and pin them, but right now we can't do that
before they've been pcim_enable()'d by a driver.
I'm indebted to David Gero for this. His bug report not only reported the
problem but identified the cause correctly and he had tested the right values
to prove what was going on
[If you backport this for 2.6.24 you will need to pull in the 2.6.25
removal of the bogus WARN_ON() in pcim_enagle]
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: David Gero <davidg@havidave.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x is now ready for production use. Bump the version,
explain what's working and what's not and drop EXPERIMENTAL.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When attached to cardbus, mmio region is at BAR 1. Other than that,
everything else is the same. Add support for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_inic162x now doesn't use any SFF features. Remove all SFF
related stuff.
* Mask unsolicited ATA interrupts. This removes our primary source of
spurious interrupts and spurious interrupt handling can be tightened
up. There's no need to clear ATA interrupts by reading status
register either.
* Don't dance with IDMA_CTL_ATA_NIEN and simplify accesses to
IDMA_CTL.
* Inherit from sata_port_ops instead of ata_sff_port_ops.
* Don't initialize or use ioaddr. There's no need to map BAR0-4
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for ATAPI commands. Write and some misc commands time out
when executed using ATAPI_PROT_DMA but ATAPI_PROT_PIO works fine. As
PIO is driven by DMA too, it doesn't make any noticeable difference
for native SATA devices. inic_check_atapi_dma() is implemented to
force PIO for those ATAPI commands.
After this change, sata_inic162x issues all commands using IDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use IDMA for PIO and non-data commands. This allows sata_inic162x to
safely drive LBA48 devices. Kill inic_dev_config() which contains
code to reject LBA48 devices.
With this change, status checking in inic_qc_issue() to avoid hard
lock up after hotplug can go away too.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The modified driver on initio site has enough clue on how to use IDMA.
Use IDMA for ATA_PROT_DMA.
* LBA48 now works as long as it uses DMA (LBA48 devices still aren't
allowed as it can destroy data if PIO is used for any reason).
* No need to mask IRQs for read DMAs as IDMA_DONE is properly raised
after transfer to memory is actually completed. There will be some
spurious interrupts but host_intr will handle it correctly and
manipulating port IRQ mask interacts badly with the other port for
some reason, so command type dependent port IRQ masking is not used
anymore.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
inic162x can't reliably read back TF or at least we don't know how to
do it yet. The only values which seem reliable are status and error.
This patch updates access to TF.
* implement inic_tf_read() which reads the TF area in mmio area
* implement custom inic_qc_fill_rtf() which only returns true if
status indicates device error. it'll be returning bogus addresses
for device errors but it'll be able to report why it failed at
least.
* implement custom inic_check_ready() and use ata_wait_after_reset()
instead of the SFF version.
* use inic_tf_read() for classification.
This is not perfect but it fixes hotplug detection failure and at
least makes the driver report 0's instead of random garbages while
reporting valid status and error for device errors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* add a bunch of constants, most are from the datasheet, a few
undocumented ones are from initio's modified driver
* HCTL_PWRDWN is bit 12 not 13
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* use larger indents for structure member definitions
* kill unused variable @addr in inic_scr_write()
* kill unnecessary flushes in inic_freeze/thaw()
* kill buggy explicit kfree() on devres managed port private data
This is in preparation of further inic162x updates.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some tidying as suggested by Grant Grundler.
Nuke local bit-counting function from sata_mv in favour of using hweight16().
Also add a short explanation for the 15msec timeout used when waiting for empty/idle.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert sata_mv's EH for FIS-based switching (FBS) over to the
sequence recommended by Marvell. This enables us to catch/analyze
multiple failed links on a port-multiplier when using NCQ.
To do this, we clear the ERR_DEV bit in the EDMA Halt-Conditions register,
so that the EDMA engine doesn't self-disable on the first NCQ error.
Our EH code sets the MV_PP_FLAG_DELAYED_EH flag to prevent new commands
being queued while we await completion of all outstanding NCQ commands
on all links of the failed PM.
The SATA Test Control register tells us which links have failed,
so we must only wait for any other active links to finish up
before we stop the EDMA and run the .error_handler afterward.
The patch also includes skeleton code for handling of non-NCQ FBS operation.
This is more for documentation purposes right now, as that mode is not yet
enabled in sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce a new "delayed error handling" mechanism in sata_mv,
to enable us to eventually deal with multiple simultaneous NCQ
failures on a single host link when a PM is present.
This involves a port flag (MV_PP_FLAG_DELAYED_EH) to prevent new
commands being queued, and a pmp bitmap to indicate which pmp links
had NCQ errors.
The new mv_pmp_error_handler() uses those values to invoke
ata_eh_analyze_ncq_error() on each failed link, prior to freezing
the port and passing control to sata_pmp_error_handler().
This is based upon a strategy suggested by Tejun.
For now, we just implement the delayed mechanism.
The next patch in this series will add the multiple-NCQ EH code
to take advantage of it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out the inner loop body of mv_host_intr()
into it's own function called mv_port_intr().
This should help maintainabilty.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the unwanted reads of hc_irq_cause from mv_host_intr(),
thereby removing a bug whereby we were not always reading it when needed..
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sigh. Undo some earlier changes to mv_port_intr(),
so that we now read/clear SError again in all cases.
Arrange the top of the function to be as close as possible
to what we need for a later update (in this series) for ERR_DEV handling.
Fix things so that libata-eh can attempt a READ_LOG_EXT_10H
in response to a failed NCQ command, by just doing a local
mv_eh_freeze() rather than ata_port_freeze().
This will now fully handle NCQ errors much of the time,
but more fixes are needed for FBS/PMP, and for certain chip errata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_config_fbs() to more closely follow the (corrected) datasheet
recommendations for NCQ and FIS-based switching (FBS).
Also, maintain a port flag to let us know when FBS is enabled.
We will make more use of that flag later in this patch series.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Part 1 of workaround for errata "sata#25" for the 60x1 series
(the second half of this errata workaround is still in development.
Bit22 of the GPIO port has to be set "on" when in NCQ mode.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EDMA engine cannot tolerate a mix of NCQ/non-NCQ commands,
and cannot be used for PIO at all. So we need to prevent libata
from trying to feed us such mixtures.
Introduce mv_qc_defer() for this purpose, and use it for all chip versions.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When performing EH, it is recommended to wait for the EDMA engine
to empty out requests-in-progress before disabling EDMA.
Introduce code to poll the EDMA_STATUS register for idle/empty bits
before disabling EDMA. For non-EH operation, this will normally exit
without delay, other than the register read.
A later series of patches may focus on eliminating this and various
other register reads (when possible) throughout the driver,
but for now we're focussing on solid reliablity.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of the GenIIe EDMA optimizations should not be used
for non-PCI (SOC) devices, and nor for certain configurations
of conventional PCI (non PCI-X, PCIe) buses.
Logic taken/simplified from that in the Marvell proprietary driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic changes; no code changes.
-- try and improve consistency of naming.
-- add missing _OFS to tails of register offset definitions.
-- rename mv_setup_ifctl() to mv_setup_ifcfg(), since that's what it really does.
-- remove/move some dead comments
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations (certain macbooks), even though all the
conditions for SIDPR access described in the datasheet are met,
actually reading those registers just returns 0 and have no effect on
write. Verify SIDPR is actually working before enabling it.
This is reported by Ryan Roth in bz#10512.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ryan Roth <ryan.roth@ch2m.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The discrete VIA ATA chips don't have 0x40 enable bits. We check that
properly in one location but not another. This causes some users 6410
RAID cards to be incorrectly skipped.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use correct variable, achieve desired result...
Spotted by LKML/linux-ide poster whose name I lost (apologies!)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tidy up naming of things associated with the PCI / SOC chip
"main irq cause/mask" registers, as inspired by Jeff.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Buffer length handling in simulated commands is error-prone and full
of bugs. There are a number of places where necessary length checks
are missing and if the output buffer is passed in as sglist, nothing
works.
This patch adds a static buffer ata_scsi_rbuf which is sufficiently
large to handle the larges output from simulated commands (4k
currently), let all simulte functions write to the buffer and removes
all length checks as we know that there always is enough buffer space.
Copying in (for ATAPI inquiry fix up) and out are handled by
sg_copy_to/from_buffer() behind ata_scsi_rbuf_get/put() interface
which handles sglist properly.
This patch is inspired from buffer length check fix patch from Petr
Vandrovec.
Updated to use sg_copy_to/from_buffer() as suggested by FUJITA
Tomonori.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Petr Vandrovec <petr@vmware.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* make ata_scsiop_*() static
* make ata_scsi_set_sense() static and move it above its users
* make ata_scsi_rbuf_fill() static
* kill unused ata_scsi_badcmd()
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The platform is actually named routerboard 532 so let's call it this. This
patch only rename files, Kconfig and C symbols; no functional changes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When count reaches 0 the postfix decrement still subtracts (to -1),
so bfin_reset_controller() returns as if the busy flag was cleared
while it was not.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Re-enable hotplug, now that the interrupt/error handling are mostly sane.
Also update the TODO list at the top.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Here it is again, minus the checkpatch.pl complaint:
Rework mv_err_intr() to leave the SError bits as-is,
so that libata-eh has a chance to see/use them.
We originally thought that clearing them here was necessary
before writing back to edma_err_cause (per the Marvell datasheets),
but we will end up reseting the chip regardless in those cases.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Continue fixing the interrupt handling logic.
Get rid of mv_intr_pio(), by using ata_sff_host_intr() for PIO..
Add a mv_unexpected_intr() catch-all for "impossible" scenarios,
where we get an interrupt that shouldn't have happened
(never seen in testing, but just in case..).
Rearrange the logic so that we always process completed
response queue entries before looking for other events,
This avoids having to re-issue commands that had already succeeded.
As part of this, we split out some duplicated functionality
into a new function, mv_get_active_qc().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tidy up host controller interrupt handling, by moving the weirdo
bit shifting from mv_interrupt() to mv_host_intr().
This lets us take advantage of the MV_PORT_TO_SHIFT_AND_HARDPORT() macro
from an earlier patch to greatly simplify the port numbering logic.
Also, defer reading the hc_irq_cause (one per hc) until it is
actually proven to be needed. This may save a microsecond or
so per interrupt, on average (a later patchset will further reduce
unnecessary register reads throughout the driver).
Apart from that, we still leave the actual IRQ handling logic alone.
Subsequent patches in this series will address that.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Try and simplify handling of the request/response queues.
Maintain the cached copies of queue indexes in a fully-masked state,
rather than having each use of them have to do the masking.
Split off handling of a single crpb response into a separate function,
to reduce complexity in the main mv_process_crpb_entries() routine.
Ignore the rarely-valid error bits from the crpb status field,
as we already handle that information in mv_err_intr().
For now, preserve the rest of the original logic.
A later patch will deal with fixing that separately.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce the MV_PORT_TO_SHIFT_AND_HARDPORT() macro,
to centralize/simplify various scattered bits of logic
for calculating bit shifts and the like.
Some of the places that do this get it wrong, too,
so consolidating the algorithm at one place will help
keep the code correct.
For now, we use the new macro in mv_eh_{freeze,thaw}.
A subsequent patch will re-use this in the interrupt handlers
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ignore *all* interrupt coalescing bits on all controllers,
not just some of each.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic cleanups prior to the interrupt/error handling logic changes.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The drive is directly soldered to the controller, so there is no cable at
all. Remove the 40-wire assumption so the drive can operate at max speed.
Before patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 5.29612 s, 25.3 MB/s
After patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 3.94955 s, 34.0 MB/s
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix mis-reporting of NCQ errors by ensuring that result_tf->flags
is properly initialized in libata-eh. This allows ata_gen_ata_sense()
to report the failed block number correctly to SCSI after a media error
during NCQ.
This patch may also be a candidate for backporting to earlier kernels.
Without this fix, SCSI will fail I/O on the entire request rather
than just the bad sector. That can be bad for a request that was
merged from many independent read reads from different tasks.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These #if's are unneeded since they:
- did anyway not handle the CONFIG_ACPI_DOCK_MODULE case correctly and
- this is already handled in include/acpi/acpi_drivers.h and
- it's now correctly handled in kconfig.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_nv hardreset can't classify but was left out while unifying
follow-up SRST request mechanism[1]. This caused detection failures
on those controllers. Fix it.
Reported and bisected by Roland Dreier, Petr Vandrovec and Marc
Dionne. Thanks guys.
[1] 305d2a1ab1
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some chips need AHCI_EN set more than once to actually set it. Try a
few times before giving up and spitting out WARN_ON().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
WARN_ON()'s in ata_hsm_move() was too liberal and got triggerred when
it shouldn't (e.g. hotplug events at the right moment). As the HSM
only deals with device errors and state machine violations, make it
check only against them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since 43cc71eed1, the platform modalias
is prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable
ATA and IDE platform drivers, to re-enable auto loading.
NOTE: both ata/pata_platform.c and ide/legacy/ide_platform.c claim
to provide "the" platform_pata driver, and there's no build-time
mutual exclusion mechanism. This means that configs which enable
both drivers will make some trouble when hotplugging...
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sis_scr_cfg_read() can't access SError and was incorrectly returning
-1 instead of -EINVAL. This went unnoticed because SError used to be
cleared in @postreset() and it didn't care about how scr_read() failed
but commit ac371987 moved SError clearing into sata_link_resume() and
SCR access failure other than -EINVAL is considered an error condition
and exposes the incorrect return value bug as detection failure. Fix
it.
Also, scsi_scr_cfg_write() was incorrectly returning 0 after it
ignored the request to write to SError. Make it also return -EINVAL.
This was bisected and reported by Patrick McHardy.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Noticed by sparse
drivers/ata/libata-core.c:3380:12: warning: function 'ata_wait_after_reset' with external linkage has definition
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (137 commits)
[SCSI] iscsi: bidi support for iscsi_tcp
[SCSI] iscsi: bidi support at the generic libiscsi level
[SCSI] iscsi: extended cdb support
[SCSI] zfcp: Fix error handling for blocked unit for send FCP command
[SCSI] zfcp: Remove zfcp_erp_wait from slave destory handler to fix deadlock
[SCSI] zfcp: fix 31 bit compile warnings
[SCSI] bsg: no need to set BSG_F_BLOCK bit in bsg_complete_all_commands
[SCSI] bsg: remove minor in struct bsg_device
[SCSI] bsg: use better helper list functions
[SCSI] bsg: replace kobject_get with blk_get_queue
[SCSI] bsg: takes a ref to struct device in fops->open
[SCSI] qla1280: remove version check
[SCSI] libsas: fix endianness bug in sas_ata
[SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
[SCSI] aacraid: Do not describe check_reset parameter with its value
[SCSI] aacraid: Fix down_interruptible() to check the return value
[SCSI] sun3_scsi_vme: add MODULE_LICENSE
[SCSI] st: rename flush_write_buffer()
[SCSI] tgt: use KMEM_CACHE macro
[SCSI] initio: fix big endian problems for auto request sense
...
The kernel now panics reliably on boot if you have a SATAPI device
connected.
The problem was introduced by the libata merge trying to pull out all
the SFF code into a separate module. Unfortunately, if you're a satapi
device you usually need to call atapi_request_sense, which has a bare
invocation of a SFF callback which is NULL on non-SFF HBAs. Fix this by
making the call conditional.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I got below log after a S3 resume in a ASUS A6VC laptop. The system has
only one IDE drive. It appears there is no reason calling _GTF for
disabled drive.
ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV0._GTF] (Node df822bd0), AE_AML_OPERAND_VALUE
ata2.00: _GTF evaluation failed (AE 0x3006)
ACPI Error (dsopcode-0483): Attempt to CreateField of length zero [20070126]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.RATA] (Node df822a7c), AE_AML_OPERAND_VALUE
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0.IDE0.CHN1.DRV1._GTF] (Node df822b94), AE_AML_OPERAND_VALUE
ata2.01: _GTF evaluation failed (AE 0x3006)
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_mv does not yet fully support hotplug (coming soon, though).
This means that the driver may not find a Silicon Image port-multiplier
when first loaded, because those devices take in exceess of 3 seconds
to sync up the SATA PHY (most devices do this in mere microseconds).
So, as a short-term interim measure, here we insert a 3-second pause
on initial driver load, once per controller board (not once per port!),
to allow the Silicon Image port-multipliers to be detected later.
This will be removed again (soon!) once hotplug is fully implemented/working.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unnecessary edma init code from port_start.
This sequence gets done later on the first I/O to the port.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add basic port-multiplier support to sata_mv.
This works in Command-based-switching mode for Gen-II chipsets,
and in FIS-based-switching mode for Gen-IIe chipsets.
Error handling remains at the primary port level for now
(works okay, but not great). This will get fixed in a subsequent
patch series for IRQ/EH handling fixes. There are also some
known NCQ/PMP errata to be dealt with in the near future,
once we have this basic PMP support in place.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The System-On-Chip (SOC) core supports all of the same
features as the other recent Marvell chips,
including NCQ and IRQ coalescing.
Fix the chip_soc flags to enable these capabilities
(note that the driver currently does nothing special
for IRQ coalescing, though).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Disable hot plug/unplug detection in sata_mv for now.
It is currently broken, and also interferes with PMP support.
This will get fixed in a subsequent patch series.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
More cosmetic cleanups to unclutter the changes needed for PMP support.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rework and simplify sata_mv's hardreset code to take advantage of
libata improvements since it was first coded.
Also, get rid of the now unnecessary prereset, postreset, and phy_reset
functions.
This patch also paves the way for subsequent pmp support patches,
which will follow once this one passes muster.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When no reset method is available, libata currently oopses. Although
the condition can't happen unless there's a bug in a low level driver,
oopsing isn't the best way to report the error condition. Complain,
dump stack and fail reset instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We have a certain number of 'ATA' emulations often on CF or other flash
devices that are at best "loosely based" on the CF 1.1 standard. These
devices report themselves as disk but don't support the ATA minimal
command set only the CF 1.1 set.
Relax the PIO checking for devices reporting ATA rev 0, or no iordy
support, or CFA. Rework the code a bit as it was already messy and this
made it quite ugly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The cable detect isolation patch inadvertently removed 40 wire short
cable handling. Put it back
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, SATA softresets should do link onlineness check before
actually performing SRST protocol but it doesn't really belong to
softreset.
This patch moves onlineness check in softreset to ata_eh_reset() and
ata_eh_followup_srst_needed() to clean up code and help future sata_mv
changes which need clear separation between SCR and TF accesses.
sata_fsl is peculiar in that its softreset really isn't softreset but
combination of hardreset and softreset. This patch adds dummy private
->prereset to keep the current behavior but the driver really should
implement separate hard and soft resets and return -EAGAIN from
hardreset if it should be follwed by softreset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some code paths which had been made obsolete by recent reset
simplification were still around. Kill them.
* ata_eh_reset() checked for ATA_DEV_UNKNOWN to determine
classification failure. This is no longer applicable.
* ata_do_reset() should convert ATA_DEV_UNKNOWN to ATA_DEV_NONE
regardless of reset result (e.g. -EAGAIN).
* LLDs don't need to convert ATA_DEV_UNKNOWN to ATA_DEV_NONE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/pata_scc.c: In function 'scc_bus_softreset':
drivers/ata/pata_scc.c:594: error: 'deadlien' undeclared (first use in this function)
drivers/ata/pata_scc.c:594: error: (Each undeclared identifier is reported only once
drivers/ata/pata_scc.c:594: error: for each function it appears in.)
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make PMP support optional by adding CONFIG_SATA_PMP and leaving out
libata-pmp.c if it isn't set. PMP helpers return constant values if
PMP support is not enabled and PMP declarations alias non-PMP
counterparts. This makes the compiler to leave out PMP related part
out and LLDs to use non-PMP counterparts automatically.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement helpers to test whether PMP is supported, attached and
determine pmp number to use when issuing SRST to a link. While at it,
move ata_is_host_link() so that it's together with the two new PMP
helpers.
This change simplifies LLDs and helps making PMP support optional.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Most of PMP support code is already in libata-pmp.c. All that are in
libata-core.c are sata_pmp_port_ops and EXPORTs. Move them to
libata-pmp.c. Also, collect PMP related prototypes and declarations
in header files and move them right above of SFF stuff.
This change is to make PMP support optional.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that SFF support is completely separated out from the core layer,
it can be made optional. Add CONFIG_ATA_SFF and let SFF drivers
depend on it. If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c
and data structures for SFF support are disabled. This saves good
number of bytes for small systems.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ap->ioaddr is to carry addresses for TF and BMDMA registers of a SFF
controller, don't abuse it in non-SFF controllers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that SFF assumptions are separated out from non-SFF reset
sequence, port_ops->sff_dev_select() is no longer necessary for
non-SFF controllers. Kill ata_noop_dev_select() and ->sff_dev_select
initialization from base and other non-SFF port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->[alt_]check_status(). In fact, no one calls them
for non-SFF drivers anymore. Kill them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->tf_read directly. It gets called only via
ops->qc_fill_rtf() for non-SFF drivers. This patch directly
implements private ops->qc_fill_rtf() for non-SFF controllers and kill
ops->tf_read().
This is much cleaner for non-SFF controllers as some of them have to
cache SFF register values in private data structure and report the
cached values via ops->tf_read(). Also, ops->tf_read() gets nasty for
controllers which don't have clear notion of TF registers when
operation is not in progress.
As this change makes default ops->qc_fill_rtf unnecessary, move
ata_sff_qc_fill_rtf() form ata_base_port_ops to ata_sff_port_ops where
it belongs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_qc_complete_multiple() took @finish_qc and called it on every qc
before completing it. This was to give opportunity to update TF cache
before ata_qc_complete() tries to fill result_tf. Now that result TF
is a separate operation, this is no longer necessary.
Update sata_sil24, which was the only user of this mechanism, such
that it implements its own ops->qc_fill_rtf() and drop @finish_qc from
ata_qc_complete_multiple().
Signed-off-by: Tejun Heo <htejun@gmail.com>
On command completion, ata_qc_complete() directly called ops->tf_read
to fill qc->result_tf. This patch adds ops->qc_fill_rtf to replace
hardcoded ops->tf_read usage.
ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is
implemented and set in ata_base_port_ops and other ops tables which
don't inherit from ata_base_port_ops, so this patch doesn't introduce
any behavior change.
ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be
called when a command finishes. As some non-SFF controllers don't
have TF registers defined unless they're associated with in-flight
commands, this limited operation makes life easier for those drivers
and help lifting SFF assumptions from libata core layer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Previously, there were two ways to trigger follow-up SRST from
hardreset method - returning -EAGAIN and leaving all device classes
unmodified. Drivers never used the latter mechanism and the only use
case for the former was when hardreset couldn't classify.
Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST
if classification is required". This change removes unnecessary
follow-up SRSTs and simplifies reset implementations.
Signed-off-by: Tejun Heo <htejun@gmail.com>
If PMP fan-out reset fails and SCR isn't accessible, PMP should be
reset. This used to be tested by sata_pmp_std_hardreset() and
communicated to EH by -ERESTART. However, this logic is generic and
doesn't really have much to do with specific hardreset implementation.
This patch moves SCR access failure detection logic to ata_eh_reset()
where it belongs. As this makes sata_pmp_std_hardreset() identical to
sata_std_hardreset(), the function is killed and replaced with the
standard method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SError used to be cleared in ->postreset. This has small hotplug race
condition. If a device is plugged in after reset is complete but
postreset hasn't run yet, its hotplug event gets lost when SError is
cleared. This patch makes sata_link_resume() clear SError. This
kills the race condition and makes a lot of sense as some PMP and host
PHYs don't work properly without SError cleared.
This change makes sata_pmp_std_{pre|post}_reset()'s unnecessary as
they become identical to ata_std counterparts. It also simplifies
sata_pmp_hardreset() and ahci_vt8251_hardreset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset(). sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.
ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.
piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sff_hardreset() contains link readiness wait logic which isn't
SFF specific. Move that part into sata_link_hardreset(), which now
takes two more parameters - @online and @check_ready. Both are
optional. The former is out parameter for link onlineness after
reset. The latter is used to wait for link readiness after hardreset.
Users of sata_link_hardreset() is updated to use new funtionality and
ahci_hardreset() is updated to use sata_link_hardreset() instead of
sata_sff_hardreset(). This doesn't really cause any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement ahci_check_ready() and replace ata_sff_wait_after_reset()
with ata_wait_after_reset(). As ahci was faking TF access, this
change doesn't result in any functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Factor out waiting logic (which is common to all ATA controllers) from
ata_sff_wait_ready() into ata_wait_ready(). ata_wait_ready() takes
@check_ready function pointer and uses it to poll for readiness. This
allows non-SFF controllers to use ata_wait_ready() to wait for link
readiness.
This patch also implements ata_wait_after_reset() - generic version of
ata_sff_wait_after_reset() - using ata_wait_ready().
ata_sff_wait_ready() is reimplemented using ata_wait_ready() and
ata_sff_check_ready(). Functionality remains the same.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Previously, post-softreset readiness is waited as follows.
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
If not, continue to #3.
3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
on devmask using ata_sff_wait_ready().
And for post-hardreset readiness,
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. sata_sff_hardreset waits for device readiness using
ata_sff_wait_ready().
This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().
ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.
ata_sff_wait_after_reset() is updated to perform the following steps.
1. waits for 150ms.
2. waits for dev0 readiness using ata_sff_wait_ready(). Note that
this is done regardless of devmask, as ata_sff_wait_ready() handles
0xff status correctly, this preserves the original behavior except
that it may wait longer after softreset if link is online but
status is 0xff. This behavior change is very unlikely to cause any
actual difference and is intended. It brings softreset behavior to
that of hardreset.
3. waits for dev1 readiness just the same way ata_bus_post_reset() did.
Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets. As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.
This change makes reset implementation simpler and more consistent.
While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap. This is to make them consistent with other
reset helpers and ease core changes.
pata_scc is updated accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_postreset() into
ata_std_postreset() and implement ata_sff_postreset() using the std
version.
ata_base_port_ops now has ata_std_postreset() for its postreset and
ata_sff_port_ops overrides it to ata_sff_postreset().
This change affects pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma
now specifies postreset to ata_sff_postreset() explicitly. sata_fsl
and sata_sil24 now use ata_std_postreset() which makes no difference
to them. ahci now calls ata_std_postreset() from its own postreset
method, which causes no behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_prereset() into
ata_std_prereset() and implement ata_sff_prereset() using the std
version. Waiting for device readiness is the only SFF specific part.
ata_base_port_ops now has ata_std_prereset() for its prereset and
ata_sff_port_ops overrides it to ata_sff_prereset(). This change can
affect pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma implements
its own prereset using ata_sff_prereset() and the rest has hardreset
and thus are unaffected by this change.
This change reflects real world situation. There is no generic way to
wait for device readiness for non-SFF controllers and some of them
don't have any mechanism for that. Non-sff drivers which don't have
hardreset should wrap ata_std_prereset() and wait for device readiness
itself but there's no such driver now and isn't likely to be popular
in the future either.
Signed-off-by: Tejun Heo <htejun@gmail.com>
->sff_irq_clear() is called only from SFF interrupt handler, so there
is no reason to initialize it for non-SFF controllers. Also,
ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF
controllers.
This patch kills ata_noop_irq_clear() and removes it from base
port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff
port_ops instead of bmdma port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add sff_ prefix to SFF specific port ops.
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SFF functions have confusing names. Some have sff prefix, some have
bmdma, some std, some pci and some none. Unify the naming by...
* SFF functions which are common to both BMDMA and non-BMDMA are
prefixed with ata_sff_.
* SFF functions which are specific to BMDMA are prefixed with
ata_bmdma_.
* SFF functions which are specific to PCI but apply to both BMDMA and
non-BMDMA are prefixed with ata_pci_sff_.
* SFF functions which are specific to PCI and BMDMA are prefixed with
ata_pci_bmdma_.
* Drop generic prefixes from LLD specific routines. For example,
bfin_std_dev_select -> bfin_dev_select.
The following renames are noteworthy.
ata_qc_issue_prot() -> ata_sff_qc_issue()
ata_pci_default_filter() -> ata_bmdma_mode_filter()
ata_dev_try_classify() -> ata_sff_dev_classify()
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames functions and doesn't
introduce any behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Fix handling of the SATA_INTERFACE_CFG register to match datasheet requirements.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean up uses of mv_stop_edma{_engine}() to match datasheet requirements.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various cosmetic fixes in preparation for real code changes later on.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_ACPI isn't selectable right now because it lacks 'short help
text'. This means it's always enabled and always enables ACPI_DOCK.
Add text so it's now [de]selectable.
cc: Jeff Garzik <jeff@garzik.org>
cc: Tejun Heo <htejun@gmail.com>
cc: Len Brown <len.brown@intel.com>
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
adma_host_stop() does the same thing that adma_port_stop() does. Kill
it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With the previous ops standardization, pdc_adma now can inherit
ata_sff_port_ops instead of ata_base_port_ops. Make the change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pdc_adma has interface similar to SFF but has its own DMA interface.
It currently implements noop bmdma ops to avoid crashing
ata_bmdma_error_handler() which BTW actually is EH for SFF drivers.
This patch makes ata_bmdma_error_handler() dereference bmdma ops iff
bmdma_addr is initialized as done in ata_bmdma_post_internal_cmd.
This change allows pdc_adma to standardize ops and use SFF
error_handler and post_internal_cmd.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_flush_code() hasn't been in use for quite some time now. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently whether a command should be retried after failure is
determined inside ata_eh_finish(). Add ATA_QCFLAG_RETRY and move the
logic into ata_eh_autopsy(). This makes things clearer and helps
extending retry determination logic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_tf_to_lba[48]() currently return LBA in tf + 1 for
ata_read_native_max_address(). Make them return LBA and make it
global so that it can be used to read LBA off TF for other purposes.
ata_read_native_max_address() now adds 1 itself.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Continues to have open issues, and engineering support is extremely difficult
to come by, according to fellow NVIDIA engineers.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ich6_sata_ahci and ich6_sata are identical. Kill ich6_sata_ahci and
drop _ahci postfixes from controller ids, which doesn't really mean
anything at this point.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_piix when attached to ICH6M in AHCI mode doesn't provide any
benefit over using ahci and has detection problems. Don't let
ata_piix claim ICH6M if it's in AHCI mode.
This change makes ICH6R the only one which ata_piix can attach to even
when it's in ahci mode which is necessary as some devices don't work
properly under ahci mode. Drop PIIX_FLAG_AHCI and match the
controller directly so that piix_disable_ahci() is called only for it.
This change makes PIIX_SCC no longer used and it gets dropped too.
This fixes bz 9491.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robert M. Albrecht <romal@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Missed one during mass conversion (dc14c0c5). Fix it. Spotted by
Stephen Rothwell.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Current code is essentially choosing between dividing by 1 or
dividing by two, make the conditions a little more obvious.
As a bonus, removes a sparse error:
drivers/ata/pata_amd.c:59:11: warning: symbol '__x' shadows an earlier one
drivers/ata/pata_amd.c:59:11: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_configure() isn't tied to any controller interface except for
the probe debug message printing at the end of the function. Kill the
message.
This is to help separating out SFF support from core layer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_pci_default_filter() doesn't really have anything to do with PCI.
It's generally applicable to BMDMA controllers. Move it out of
CONFIG_PCI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Move SFF related functions from libata-core.c to libata-sff.c.
ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(),
ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(),
ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(),
ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(),
sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(),
ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(),
ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(),
atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(),
ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(),
ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(),
ata_interrupt(), ata_std_ports()
* Make ata_pio_queue_task() global as it's now called from
libata-sff.c.
* Move SFF related stuff in include/linux/libata.h and
drivers/ata/libata.h into one place. While at it, move timing
constants into the global enum definition and fortify comments a
bit.
This patch strictly moves stuff around and as such doesn't cause any
functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reorder functions in drivers/ata/libata-sff.c such that functions
generally follow ops table order and init functions come last. This
is in preparation of SFF cleanup.
This patch strictly moves stuff around and as such doesn't cause any
functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is no reason to issue device select in read_id, it will be done
by ops->qc_issue() when IDENTIFY[_PACKET] is issued via
ata_exec_internal().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently reset methods are not specified directly in the
ata_port_operations table. If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods. It's done this way for two reasons.
First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.
Second, as ->error_handler uses those reset methods, it can get
confusing. ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.
Now that ops table uses inheritance, the first problem doesn't exist
anymore. The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks. In fact, there currently is no driver which actually
modifies error handling behavior. Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH. I don't think making ops layering strict has
any noticeable benefit.
This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops. Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.
* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
aren't accessible. sata_promise doesn't need to use separate
error_handlers for PATA and SATA anymore.
* softreset is broken for sata_inic162x and sata_sx4. As libata now
always prefers hardreset, this doesn't really matter but the ops are
forced to NULL using ATA_OP_NULL for documentation purpose.
* pata_hpt374 needs to use different prereset for the first and second
PCI functions. This used to be done by branching from
hpt374_error_handler(). The proper way to do this is to use
separate ops and port_info tables for each function. Converted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata core layer doesn't care about sht or ->irq_handler. Those are
only of interest to the LLD during initialization. This is confusing
and has caused several drivers to have duplicate unused initializers
for these fields.
Currently only sata_nv uses these fields. Make sata_nv use
->private_data, which is supposed to carry LLD-specific information,
instead and kill ->sht and ->irq_handler. nv_pi_priv structure is
defined and struct literals are used to initialize private_data.
Notational overhead is negligible.
Signed-off-by: Tejun Heo <htejun@gmail.com>
port_info->private_data is currently used for two purposes - to record
private data about the port_info or to specify host->private_data to
use when allocating ata_host.
This overloading is confusing and counter-intuitive in that
port_info->private_data becomes host->private_data instead of
port->private_data. In addition, port_info and host don't correspond
to each other 1-to-1. Currently, the first non-NULL
port_info->private_data is used.
This patch makes port_info->private_data just be what it is -
private_data for the port_info where LLD can jot down extra info.
libata no longer sets host->private_data to the first non-NULL
port_info->private_data, @host_priv argument is added to
ata_pci_init_one() instead. LLDs which use ata_pci_init_one() can use
this argument to pass in pointer to host private data. LLDs which
don't should use init-register model anyway and can initialize
host->private_data directly.
Adding @host_priv instead of using init-register model for LLDs which
use ata_pci_init_one() is suggested by Alan Cox.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
ata_pci_init_one() is the only function which uses ops->irq_handler
and pi->sht. Other initialization functions take the same information
as arguments. This causes confusion and duplicate unused entries in
structures.
Make ata_pci_init_one() take sht as an argument and use ata_interrupt
implicitly. All current users use ata_interrupt and if different irq
handler is necessary open coding ata_pci_init_one() using
ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
lines including error handling and driver which requires custom
interrupt handler is likely to require custom initialization anyway.
As ata_pci_init_one() was the last user of ops->irq_handler, this
patch also kills the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build ata_port_operations table and
register it with libata core layer. This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.
This becomes worse for drivers which support related similar
controllers which differ slightly. They share most of the operations
except for a few. However, the driver still needs to list all
operations for each variant. This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.
This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone. When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time. Some of those inconsistencies
cause immediate problems and fixed. Others just remain there dormant
making maintenance increasingly difficult.
To rectify the problem, this patch implements ata_port_operations
inheritance. To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance. An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop. When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified. This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.
libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma. To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.
After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to. The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.
* sata_sx4 is still using old style EH and currently doesn't take
advantage of ops inheritance.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer. This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.
This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht. Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.
All sht tables are identical before and after this patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Over the time, port info, ops and sht structures developed quite a bit
of inconsistencies. This patch updates drivers.
* Enable/disable_pm callbacks added to all ahci ops tables.
* Every driver for SFF controllers now uses ata_sff_port_start()
instead of ata_port_start() unless the driver has custom
implementation.
* Every driver for SFF controllers now uses ata_pci_default_filter()
unless the driver has custom implementation.
* Removed an odd port_info->sht initialization from ata_piix.c.
Likely a merge byproduct.
* A port which has ATA_FLAG_SATA set doesn't need to set cable_detect
to ata_cable_sata(). Remove it from via and mv port ops.
* Some drivers had unnecessary .max_sectors initialization which is
ignored and was missing .slave_destroy callback. Fixed.
* Removed unnecessary sht initializations port_info's.
* Removed onsolete scsi device suspend/resume callbacks from
pata_bf54x.
* No reason to set ata_pci_default_filter() and bmdma functions for
PIO-only drivers. Remove those callbacks and replace
ata_bmdma_irq_clear with ata_noop_irq_clear.
* pata_platform sets port_start to ata_dummy_ret0. port_start can
just be set to NULL.
* sata_fsl supports NCQ but was missing qc_defer. Fixed.
* pata_rb600_cf implements dummy port_start. Removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
->irq_clear() is used to clear IRQ bit of a SFF controller and isn't
useful for drivers which don't use libata SFF HSM implementation.
However, it's a required callback and many drivers implement their own
noop version as placeholder. This patch implements ata_noop_irq_clear
and use it to replace those custom placeholders.
Also, SFF drivers which don't support BMDMA don't need to use
ata_bmdma_irq_clear(). It becomes noop if BMDMA address isn't
initialized. Convert them to use ata_noop_irq_clear().
Signed-off-by: Tejun Heo <htejun@gmail.com>
PCI device should be powered up or powered up before its PCI regsiters
are accessed. Although PCI configuration register access is allowed
in D3hot, PCI device is free to reset its status when transiting from
D3hot to D0 causing configuration data to change.
Many libata SFF drivers which use ata_pci_init_one() read and update
configuration registers before calling ata_pci_init_one() which
enables the PCI device. Also, in resume paths, some drivers access
registers without resuming the PCI device.
This patch adds a call to pcim_enable_device() in init path if
register is accessed before calling ata_pci_init_one() and make resume
paths first resume PCI devices, access PCI configuration regiters then
resume ATA host.
While at it...
* cmd640 was strange in that it set ->resume even when CONFIG_PM is
not. This is by-product of minimal build fix. Updated.
* In cs5530, Don't BUG() on reinit failure. Just whine and fail
resume.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_ehi_schedule_probe() was created to hide details of link-resuming
reset magic. Now that all the softreset workarounds are gone,
scheduling probe is very simple - set probe_mask and request RESET.
Kill ata_ehi_schedule_probe() and open code it. This also increases
consistency as ata_ehi_schedule_probe() couldn't cover individual
device probings so they were open-coded even when the helper existed.
While at it, define ATA_ALL_DEVICES as mask of all possible devices on
a link and always use it when requesting probe on link level for
simplicity and consistency. Setting extra bits in the probe_mask
doesn't hurt anybody.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Some controllers can't reliably record the initial D2H FIS after SATA
link is brought online for whatever reason. Advanced controllers
which don't have traditional TF register based interface often have
this problem as they don't really have the TF registers to update
while the controller and link are being initialized.
SKIP_D2H_BSY works around the problem by skipping the wait for device
readiness before issuing SRST, so for such controllers libata issues
SRST blindly and hopes for the best.
Now that libata defaults to hardreset, this workaround is no longer
necessary. For controllers which have support for hardreset, SRST is
never issued by itself. It is only issued as follow-up SRST for
device classification and PMP initialization, so there's no need to
wait for it from prereset.
Kill ATA_LFLAG_SKIP_D2H_BSY.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ATA_EHI_RESUME_LINK has two functions - promote reset to hardreset if
ATA_LFLAG_HRST_TO_RESUME is set and preventing EH from shortcutting
reset action when probing is requested. The former is gone now and
the latter can easily be achieved by making EH to perform at least one
reset if reset is requested, which also makes more sense than
depending on RESUME_LINK flag.
As ATA_EHI_RESUME_LINK was the only EHI reset modifier, this also
kills reset modifier handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that hardreset is the preferred method of resetting, there's no
need for ATA_LFLAG_HRST_TO_RESUME flag. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
When both soft and hard resets are available, libata preferred
softreset till now. The logic behind it was to be softer to devices;
however, this doesn't really help much. Rationales for the change:
* BIOS may freeze lock certain things during boot and softreset can't
unlock those. This by itself is okay but during operation PHY event
or other error conditions can trigger hardreset and the device may
end up with different configuration.
For example, after a hardreset, previously unlockable HPA can be
unlocked resulting in different device size and thus revalidation
failure. Similar condition can occur during or after resume.
* Certain ATAPI devices require hardreset to recover after certain
error conditions. On PATA, this is done by issuing the DEVICE RESET
command. On SATA, COMRESET has equivalent effect. The problem is
that DEVICE RESET needs its own execution protocol.
For SFF controllers with bare TF access, it can be easily
implemented but more advanced controllers (e.g. ahci and sata_sil24)
require specialized implementations. Simply using hardreset solves
the problem nicely.
* COMRESET initialization sequence is the norm in SATA land and many
SATA devices don't work properly if only SRST is used. For example,
some PMPs behave this way and libata works around by always issuing
hardreset if the host supports PMP.
Like the above example, libata has developed a number of mechanisms
aiming to promote softreset to hardreset if softreset is not going
to work. This approach is time consuming and error prone.
Also, note that, dependingon how you read the specs, it could be
argued that PMP fan-out ports require COMRESET to start operation.
In fact, all the PMPs on the market except one don't work properly
if COMRESET is not issued to fan-out ports after PMP reset.
* COMRESET is an integral part of SATA connection and any working
device should be able to handle COMRESET properly. After all, it's
the way to signal hardreset during reboot. This is the most used
and recommended (at least by the ahci spec) method of resetting
devices.
So, this patch makes libata prefer hardreset over softreset by making
the following changes.
* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
ATA_EH_{SOFT|HARD}RESET used to be used. ATA_EH_{SOFT|HARD}RESET is
now only used to tell prereset whether soft or hard reset will be
issued.
* Strip out now unneeded promote-to-hardreset logics from
ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
other places.
Signed-off-by: Tejun Heo <htejun@gmail.com>
This patch makes the needlessly global ali_atapi_dma static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to Broadcom, two chips have their port counts flipped. The proper
count is:
0x241 is 8 ports
0x242 is 4 ports
Reported by Yohei Honda on kernel bz 10424.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In sata_fsl_probe memory is allocated but never used or deallocated.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=10404
Thanks to Daniel Marjamäki for the bug report.
Reported-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit 0f436eff54 breaks build on
arch/ppc as it doesn't implement the machine_is() macro.
This fixes it by using CONFIG_PPC_MERGE instead which represents
arch/powerpc only, while CONFIG_PPC is set for both.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATAPI DMA just doesn't work reliably on pata_ali. The IDE driver can
do it but for some mysterious reason, pata_ali can't. This patch
disables it by default and makes the driver whine during
initialization. "pata_ali.atapi_dma" parameter is added so that user
can bypass the workaround.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SAT passthrus don't really fit into ATAPI_MISC class. SAT passthru
commands always transfer multiple of 512 bytes and variable length
response is not allowed. This patch creates a separate category -
ATAPI_PASS_THRU - for these.
This fixes HSM violation on "hdparm -I".
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Uninline atapi_cmd_type(). It doesn't really have to be inline and
more case will be added which need to access unexported libata
variable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit f58229f806 accidentally made
ata_bus_probe() not use reverse order probing. Fix it.
There currently isn't any PATA driver which uses obsolete
ata_bus_probe() path, so this patch is mainly for correctness.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
as prescribed in Documentation/powerpc/booting-without-of.txt.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
EH actions are ATA_EH_* not ATA_EHI_*. Rename ATA_EHI_LPM to
ATA_EH_LPM.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There have been reported regressions of the SIL 680 driver when using MMIO, so
this makes it only try MMIO on Cell blades where it's known to be necessary
(the host bridge doesn't do PIO on these).
We'll try to find the root problem with MMIO separately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make it possible to pass mbus_dram_target_info to the sata_mv
driver via the platform data, make the sata_mv driver program
the window registers based on this data if it is passed in, and
make the Orion platform setup code use this method instead of
programming the SATA mbus window registers by hand.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
At least one report claims that a878539ef9
failed to solve lockups, whereas the old limit-to-32-bit trick worked.
Restore the 32-bit limit, but also leave the 255-sector limit in place,
because we know that's needed as well.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A Promise SATA controller will signal hotplug events when a hard
reset (COMRESET) is done on a port. These events aren't masked by
the driver, and the unexpected interrupts will cause a sequence
of failed reset attempts util libata's EH finally gives up.
This has not been a common problem so far, but the pending libata
hardreset-by-default changes makes it a critical issue.
The solution is to disable hotplug events before a reset, and to
reenable them afterwards. (Promise's driver does this too.)
This patch adds SATA-specific versions of ->freeze() and ->thaw()
that also disable and enable hotplug events. PATA ports continue
to use the old versions of ->freeze() and ->thaw().
Accesses to the hotplug register must be serialised via host->lock.
We rely on ap->lock == &ap->host->lock and that libata takes this
lock before ->freeze() and ->thaw(). Document this requirement.
The interrupt handler is adjusted so its hotplug register accesses
are inside the region protected by host->lock.
Tested on various chips (SATA300TX4, SATA300TX2plus, SATAII150TX4,
FastTrack TX4000) with various combinations of SATA and PATA disks,
with and without the pending hardreset-by-default changes.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's no point in retrying and eventually failing device detection
when the device rejects READ_NATIVE_MAX[_EXT]. Disable HPA unlocking
if READ_NATIVE_MAX[_EXT] is rejected as done when SET_MAX[_EXT] is
rejected.
This allows some old drives to work even if they aren't blacklisted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is to fix bugzilla #10254. QSI cdrom attached to pata_sis as
secondary master appears as phantom device for the slave.
Interestingly, instead of not setting DRQ after IDENTIFY which
triggers NODEV_HINT, it aborts both IDENTIFY and IDENTIFY PACKET which
makes EH retry.
Modify EH such that it assumes no device is attached if both flavors
of IDENTIFY are aborted by the device. There really isn't much point
in retrying when the device actively aborts the commands.
While at it, convert NODEV detection message to ata_dev_printk() to
help debugging obscure detection problems.
This problem was reported by Jan Bücken.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jan Bücken <jb.faq@gmx.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_it821x needs to look at raw request size in check_atapi_dma().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ata_qc_raw_nbytes() which determines the raw user-requested
size of a PC command.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/ata/libata-acpi.c fails to build
drivers/built-in.o: In function `ata_acpi_associate':
(.text+0x7106a): undefined reference to `register_hotplug_dock_device'
When CONFIG_ATA_ACPI=y and CONFIG_ACPI_DOCK=m
But if dock is selected from ata_acpi, dock will =y
when ata_acpi=y, avoiding this problem.
http://bugzilla.kernel.org/show_bug.cgi?id=10272
Signed-off-by: Len Brown <len.brown@intel.com>
pata_ali was using qc->nbytes to determine whether a command is
data transfer type or not. As now qc->nbytes can be extended by
padding and draining buffers, these tests are not useful anymore.
Use atapi_cmd_type() instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Under certain circumstances (SSP turned off by the BIOS) and for
debugging purposes, skipping global controller reset is helpful. Add
a kernel parameter for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci is often implemented with accompanying SFF compatible interface
and legacy IDE driver may attach to the legacy IO ports when the
controller is already claimed by ahci and vice-versa. This patch
makes ahci use pcim_iomap_regions_request_all() so that all IO regions
are claimed on attach.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve ACPI hotplug handling such that dock event is handled properly.
* Register handlers for dock events.
* Directly detach device on EJECT_REQUEST instead of signaling hotplug
event. This prevents libata from accessing severed controller
and/or device.
* While at it, use named constants for ACPI events and move uevent
signaling inside host lock.
Original patch and testing by Holger Macht.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Buffer for force param is deallocated after initialization, so trying
to read it via sysfs results in oops. Don't allow read access to the
param node.
Spotted by Eric Sesterhenn.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SFF incorrectly assumed that ctl register is available for all
controllers while some old SFF controllers don't have ctl register.
Make SFF handle controllers w/o ctl register by conditionalizing ctl
register access and softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some old SFF controllers don't have any way to reset the channel.
Currently, this isn't supported and libata EH causes an oops. Allow
LLDs w/o any reset method and just assume ATA class in such cases.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This addresses the recent ATI SB600 errata, where the hardware does
not like 256-length PRD entries during FPDMA (aka NCQ).
It hurts performance on SB600, but it is more important to get a
correct patch eliminating the data corruption/lockups, and then later
on tune for performance.
We simply limit each command to a maximum of 255 sectors, on SB600.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When masking, mask out the modes that are unsupported not the ones
that are supported. This makes life happier.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Block layer alignment was used for two different purposes - memory
alignment and padding. This causes problems in lower layers because
drivers which only require memory alignment ends up with adjusted
rq->data_len. Separate out padding such that padding occurs iff
driver explicitly requests it.
Tomo: restorethe code to update bio in blk_rq_map_user
introduced by the commit 40b01b9bbd
according to padding alignment.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The meaning of rq->data_len was changed to the length of an allocated
buffer from the true data length. It breaks SG_IO friends and
bsg. This patch restores the meaning of rq->data_len to the true data
length and adds rq->extra_len to store an extended length (due to
drain buffer and padding).
This patch also removes the code to update bio in blk_rq_map_user
introduced by the commit 40b01b9bbd.
The commit adjusts bio according to memory alignment
(queue_dma_alignment). However, memory alignment is NOT padding
alignment. This adjustment also breaks SG_IO friends and bsg. Padding
alignment needs to be fixed in a proper way (by a separate patch).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
Interrupts must be disabled if using kmap_atomic(KM_IRQ0), but that was
not the case in a few code paths coming directly from ATA driver
interrupt handlers (which use spin_lock rather than spin_lock_irqsave).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support (including ATAPI DMA) for HT1100 (aka BCM11000) SATA controller.
Signed-off-by: Anantha Subramanyam <ananth@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix libata-core kernel-doc warning:
Warning(linux-2.6.25-rc2-git6//drivers/ata/libata-core.c:168): No description found for parameter 'ap'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stephen Rothwell