Commit graph

1560 commits

Author SHA1 Message Date
Tejun Heo
6a6b97d360 libata: improve phantom device detection
Currently libata uses four methods to detect device presence.

1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine

Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe.  In both cases, PHY status wasn't available.  In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4.  The other failed #2 but as it passed #3 and #4,
it still caused failure.

In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-14 18:51:57 -05:00
Tejun Heo
19b723218b libata: fix last_reset timestamp handling
ehc->last_reset is used to ensure that resets are not issued too
close to each other.  It's initialized to jiffies minus one minute
on EH entry.  However, when new links are initialized after PMP is
probed, new links have zero for this timestamp resulting in long wait
depending on the current jiffies.

This patch makes last_set considered iff ATA_EHI_DID_RESET is set, in
which case last_reset is always initialized.  As an added precaution,
WARN_ON() is added so that warning is printed if last_reset is
in future.

This problem is spotted and debugged by Shane Huang.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shane Huang <Shane.Huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 03:01:21 -05:00
Roland Dreier
44901a9684 libata: Avoid overflow in ata_tf_read_block() when tf->hba_lbal > 127
Phillip O'Donnell <phillip.odonnell@gmail.com> pointed out that the same
sign extension bug that was fixed in commit ba14a9c2 ("libata: Avoid
overflow in ata_tf_to_lba48() when tf->hba_lbal > 127") also appears to
exist in ata_tf_read_block().  Fix this by adding a cast to u64.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 02:59:27 -05:00
Marc Pignat
a12d6c9a09 [libata] pata_pcmcia: another memory card support
Support for Apacer photo steno pro card.

Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 02:59:13 -05:00
Mark Salter
bc170e6568 [libata] pata_sch: notice attached slave devices
I posted this last month, but was prompted to do so again in bz#467457

Add capability flag to support slave devices with pata_sch driver.

Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 02:58:59 -05:00
Qinghuang Feng
bd6b52a17b [libata] pata_cs553*.c: cleanup kernel-doc
No arguments named @deadline in cs5535_cable_detect() and
cs5536_cable_detect().  Remove them.

Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-11 02:58:30 -05:00
Tejun Heo
8a8bc22332 libata: revert convert-to-block-tagging patches
This patch reverts the following three commits which convert libata to
use block layer tagging.

 43a49cbdf3
 e013e13bf6
 2fca5ccf97

Although using block layer tagging is the right direction, due to the
tight coupling among tag number, data structure allocation and
hardware command slot allocation, libata doesn't work correctly with
the current conversion.

The biggest problem is guaranteeing that tag 0 is always used for
non-NCQ commands.  Due to the way blk-tag is implemented and how SCSI
starts and finishes requests, such guarantee can't be made.  I'm not
sure whether this would actually break any low level driver but it
doesn't look like a good idea to break such assumption given the
frailty of ATA controllers.

So, for the time being, keep using the old dumb in-libata qc
allocation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axobe <jens.axboe@oracle.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-10 08:04:47 -08:00
Tejun Heo
299246f9a2 libata: mask off DET when restoring SControl for detach
libata restores SControl on detach; however, trying to restore
non-zero DET can cause undeterministic behavior including PMP device
going offline till power cycling.  Mask off DET when restoring
SControl.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:33 -05:00
Tejun Heo
6a87e42e95 libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply it
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers.  Implement a horkage to skip the mod16 check and apply
it to the quantum device.

This is reported by John Clark in the following thread.

  http://thread.gmane.org/gmane.linux.ide/34748

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:27 -05:00
Elias Oltmanns
a464189de3 libata: Fix a potential race condition in ata_scsi_park_show()
Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:24 -05:00
Tejun Heo
3c324283e6 sata_nv: fix generic, nf2/3 detection regression
All three flavors of sata_nv's are different in how their hardreset
behaves.

* generic: Hardreset is not reliable.  Link often doesn't come online
  after hardreset.

* nf2/3: A little bit better - link comes online with longer debounce
  timing.  However, nf2/3 can't reliable wait for the first D2H
  Register FIS, so it can't wait for device readiness or classify the
  device after hardreset.  Follow-up SRST required.

* ck804: Hardreset finally works.

The core layer change to prefer hardreset and follow up changes
exposed the above issues and caused various detection regressions for
all three flavors.  This patch, hopefully, fixes all the known issues
and should make sata_nv error handling more reliable.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:11 -05:00
Marcin Slusarz
554d491de1 sata_via: restore vt*_prepare_host error handling
commit b9d5b89b48 (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it

catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:06 -05:00
Mikael Pettersson
cadef677e4 sata_promise: add ATA engine reset to reset ops
Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.

The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.

To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:03 -05:00
Jens Axboe
9ce8e3073d libata: add whitelist for devices with known good pata-sata bridges
libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.

So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 01:45:06 -04:00
Tejun Heo
b9d5b89b48 sata_via: fix support for 5287
5287 used to be treated as vt6420 but it didn't work.  It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports.  This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata.  Another controller
which falls into this category is ata_piix w/ SIDPR access.

libata now has facility to deal with this class of controllers named
slave_link.  A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.

This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.

This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.

  http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 01:43:28 -04:00
Roland Dreier
ba14a9c291 libata: Avoid overflow in ata_tf_to_lba48() when tf->hba_lbal > 127
In ata_tf_to_lba48(), when evaluating

	(tf->hob_lbal & 0xff) << 24

the expression is promoted to signed int (since int can hold all values
of u8).  However, if hob_lbal is 128 or more, then it is treated as a
negative signed value and sign-extended when promoted to u64 to | into
sectors, which leads to the MSB 32 bits of section getting set
incorrectly.

For example, Phillip O'Donnell <phillip.odonnell@gmail.com> reported
that a 1.5GB drive caused:

    ata3.00: HPA detected: current 2930277168, native 18446744072344861488

where 2930277168 == 0xAEA87B30 and 18446744072344861488 == 0xffffffffaea87b30
which shows the problem when hob_lbal is 0xae.

Fix this by adding a cast to u64, just as is used by for hob_lbah and
hob_lbam in the function.

Reported-by: Phillip O'Donnell <phillip.odonnell@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 01:42:59 -04:00
Randy Dunlap
5b97fbd093 ATA: remove excess kernel-doc notation
Remove excess kernel-doc function parameter notation from drivers/ata/:

Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task'
Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete'
Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 01:42:49 -04:00
Linus Torvalds
3c136f29ba Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: ahci enclosure management bit mask
  libata: ahci enclosure management led sync
  pata_ninja32: suspend/resume support
  libata: Fix LBA48 on pata_it821x RAID volumes.
  libata: clear saved xfer_mode and ncq_enabled on device detach
  sata_sil24: configure max read request size to 4k
  libata: add missing kernel-doc
  libata: fix device iteration bugs
  ahci: Add support for Promise PDC42819
  ata: Switch all my stuff to a common address
2008-10-28 09:42:48 -07:00
David Milburn
87943acf60 libata: ahci enclosure management bit mask
Enclosure management bit mask definitions.

Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-28 00:37:15 -04:00
David Milburn
eb40963c83 libata: ahci enclosure management led sync
Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock.

Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-28 00:36:10 -04:00
Alan Cox
e7c0d217cd pata_ninja32: suspend/resume support
I had assumed that the standard recovery would be sufficient for this
hardware but it isn't. Fix up the other registers on resume as needed. See
bug #11735

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-28 00:35:59 -04:00
Ondrej Zary
054e5f616b libata: Fix LBA48 on pata_it821x RAID volumes.
[http://lkml.org/lkml/2008/10/18/82]

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:56:33 -04:00
Tejun Heo
90484ebfc9 libata: clear saved xfer_mode and ncq_enabled on device detach
libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed.  These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:40 -04:00
Tejun Heo
e8b3b5e9f5 sata_sil24: configure max read request size to 4k
Due to request posting limitations, bandwidth of sil3132 is limited to
around 120MB/s with the minimum pci-e payload size (128bytes) which is
used by most consumer systems.  However, write throughput can be
slightly (~3%) increased by increasing the max read requeset size.
Configure it to 4k which is the maximum supported.  This optimization
is also done by SIMG's windows driver.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:27 -04:00
Randy Dunlap
3cd8ddbd86 libata: add missing kernel-doc
Fix libata missing kernel-doc:

Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description
found for parameter 'tag'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:23 -04:00
Tejun Heo
4a9c7b3359 libata: fix device iteration bugs
There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.

* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()

While at it, reformat comments in cable_is_40wire().

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:55:12 -04:00
Mark Nelson
c77a036bec ahci: Add support for Promise PDC42819
Add an appropriate entry for the Promise PDC42819 controller. It has an
AHCI mode and so far works correctly with board_ahci.

This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port)
software-based RAID cards (for which there is a binary driver, t3sas) and
can be found on some motherboards, for example the MSI K9A2 Platinum,
which calls the chip a Promise T3 controller.

Although this controller also supports SAS devices, its default bootup mode
is AHCI and the binary driver has to do some magic to get the chip into the
appropriate mode to drive SAS disks.

Seeing as no documentation is provided by Promise, adding this entry to the
ahci driver allows the controller to be useful to people as a SATA
controller (with no ill effects on the system if a SAS disk is connected -
probing of the port just times out with "link online but device
misclassified"), without having to resort to using the binary driver. Users
who require SAS or the proprietary software raid can get this functionality
using the binary driver.

Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:54:55 -04:00
Alan Cox
ab77163008 ata: Switch all my stuff to a common address
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-27 23:54:50 -04:00
Jens Axboe
43a49cbdf3 libata: fix NCQ devices behind port multipliers
For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-27 19:25:30 +01:00
Jens Axboe
e013e13bf6 libata: fix bug with non-ncq devices
The recent commit 2fca5ccf97 ("libata:
switch to using block layer tagging support") to enable support for
block layer tagging in libata was broken for non-NCQ devices

The block layer initializes the tag field to -1 to detect invalid uses
of a tag, and if the libata devices does NOT support NCQ, we just used
that field to index the internal command list.  So we need to check for
-1 first and only use the tag field if it's valid.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-24 08:22:38 -07:00
Jens Axboe
2fca5ccf97 libata: switch to using block layer tagging support
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-23 16:05:26 -07:00
Linus Torvalds
765426e8ee Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits)
  dock: make dock driver not a module
  ACPI: fix ia64 build warning
  ACPI: hack around sysfs warning with link order
  ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n
  intel_menlo: fix build warning
  panasonic-laptop: fix build
  ACPICA: Update version to 20080926
  ACPICA: Add support for zero-length buffer-to-string conversions
  ACPICA: New: Validation for predefined ACPI methods/objects
  ACPICA: Fix for implicit return compatibility
  ACPICA: Fixed a couple memory leaks associated with "implicit return"
  ACPICA: Optimize buffer allocation procedure
  ACPICA: Fix possible memory leak, error exit path
  ACPICA: Fix fault after mem allocation failure in AML parser
  ACPICA: Remove unused ACPI register bit definition
  ACPICA: Update version to 20080829
  ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname
  ACPICA: Cleanup for internal Reference Object
  ACPICA: Update comments - no functional changes
  ACPICA: Update for Reference ACPI_OPERAND_OBJECT
  ...
2008-10-23 10:20:36 -07:00
Len Brown
057316cc6a Merge branch 'linus' into test
Conflicts:
	MAINTAINERS
	arch/x86/kernel/acpi/boot.c
	arch/x86/kernel/acpi/sleep.c
	drivers/acpi/Kconfig
	drivers/pnp/Makefile
	drivers/pnp/quirks.c

Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-23 00:11:07 -04:00
Len Brown
47bf31adc5 Merge branch 'dock' into test
Conflicts:
	drivers/acpi/osl.c

Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-22 23:25:26 -04:00
Tejun Heo
b78152e9db sata_via: load DEVICE register when CTL changes
VIA controllers clear DEVICE register when IEN changes.  Make sure
DEVICE is updated along with CTL.

This change is separated from Joseph Chan's larger patch.

  http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:42:47 -04:00
Tejun Heo
816ab89782 libata: set device class to NONE if phys_offline
Reset methods don't have access to phys link status for slave links
and may incorrectly indicate device presence causing unnecessary probe
failures for unoccupied links.  This patch clears device class to NONE
during post-reset processing if phys link is offline.

As on/offlineness semantics is strictly defined and used in multiple
places by the core layer, this won't change behavior for drivers which
don't use slave links.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:42:43 -04:00
Tejun Heo
a568d1d2e2 libata-eh: fix slave link EH action mask handling
Slave link action mask is transferred to master link and all the EH
actions are taken by the master link.  ata_eh_about_to_do() and
ata_eh_done() are called with ATA_EH_ALL_ACTIONS to clear the slave
link actions during transfer.  This always sets ATA_PFLAG_RECOVERED
flag causing spurious "EH complete" messages.

Don't set ATA_PFLAG_RECOVERED for slave link actions.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:21 -04:00
Tejun Heo
848e4c68c4 libata: transfer EHI control flags to slave ehc.i
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH.  As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.

This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:19 -04:00
Tejun Heo
570106df6b libata-sff: fix ata_sff_post_internal_cmd()
ata_sff_post_internal_cmd() needs to grab port lock before calling
ata_bmdma_stop() and also need to clear hsm_task_state.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:15 -04:00
Tejun Heo
f667fdbbbe libata: initialize port_task when !CONFIG_ATA_SFF
ap->port_task was not initialized if !CONFIG_ATA_SFF later triggering
lockdep warning.  Make sure it's initialized.

Reported by Larry Finger.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:01 -04:00
Benjamin Herrenschmidt
6dc6472581 Merge commit 'origin'
Manual fixup of conflicts on:

	arch/powerpc/include/asm/dcr-regs.h
	drivers/net/ibm_newemac/core.h
2008-10-15 11:31:54 +11:00
Linus Torvalds
2be4ff2f08 Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (49 commits)
  pcmcia: ioctl-internal definitions
  pcmcia: cistpl header cleanup
  pcmcia: remove unused argument to pcmcia_parse_tuple()
  pcmcia: card services header cleanup
  pcmcia: device_id header cleanup
  pcmcia: encapsulate ioaddr_t
  pcmcia: cleanup device driver header file
  pcmcia: cleanup socket services header file
  pcmcia: merge ds_internal.h into cs_internal.h
  pcmcia: cleanup cs_internal.h
  pcmcia: cs_internal.h is internal
  pcmcia: use dev_printk for cs_error()
  pcmcia: remove CS_ error codes alltogether
  pcmcia: deprecate CS_BAD_TUPLE
  pcmcia: deprecate CS_BAD_ARGS
  pcmcia: deprecate CS_BAD_BASE, CS_BAD_IRQ, CS_BAD_OFFSET and CS_BAD_SIZE
  pcmcia: deprecate CS_BAD_ATTRIBUTE, CS_BAD_TYPE and CS_BAD_PAGE
  pcmcia: deprecate CS_NO_MORE_ITEMS
  pcmcia: deprecate CS_IN_USE
  pcmcia: deprecate CS_CONFIGURATION_LOCKED
  ...

Fix trivial conflict in drivers/pcmcia/ds.c manually
2008-10-13 14:12:40 -07:00
Linus Torvalds
0710483959 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (180 commits)
  leo: disable cursor when leaving graphics mode
  cg6: disable cursor when leaving graphics mode
  sparc32: sun4m interrupt mask cleanup
  drivers/rtc/Kconfig: don't build rtc-cmos.o on sparc32
  sparc: arch/sparc/kernel/pmc.c -- extra #include?
  sparc32: Add more extensive documentation of sun4m interrupts.
  sparc32: Kill irq_rcvreg from sun4m_irq.c
  sparc32: Delete master_l10_limit.
  sparc32: Use PROM device probing for sun4c timers.
  sparc32: Use PROM device probing for sun4c interrupt register.
  sparc32: Delete claim_ticker14().
  sparc32: Stop calling claim_ticker14() from sun4c_irq.c
  sparc32: Kill clear_profile_irq btfixup entry.
  sparc32: Call sun4m_clear_profile_irq() directly from sun4m_smp.c
  sparc32: Remove #if 0'd code from sun4c_irq.c
  sparc32: Remove some SMP ifdefs in sun4d_irq.c
  sparc32: Use PROM infrastructure for probing and mapping sun4d timers.
  sparc32: Use PROM device probing for sun4m irq registers.
  sparc32: Use PROM device probing for sun4m timer registers.
  sparc: Fix user_regset 'n' field values.
  ...
2008-10-12 11:40:55 -07:00
David S. Miller
56c5d900db Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	sound/core/memalloc.c
2008-10-11 12:39:35 -07:00
Bartlomiej Zolnierkiewicz
a4f19040a3 libata: WIN_* -> ATA_CMD_*
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-10-10 22:39:20 +02:00
Linus Torvalds
e26feff647 Merge branch 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
  doc/cdrom: Trvial documentation error, file not present
  block_dev: fix kernel-doc in new functions
  block: add some comments around the bio read-write flags
  block: mark bio_split_pool static
  block: Find bio sector offset given idx and offset
  block: gendisk integrity wrapper
  block: Switch blk_integrity_compare from bdev to gendisk
  block: Fix double put in blk_integrity_unregister
  block: Introduce integrity data ownership flag
  block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
  bio.h: Remove unused conditional code
  block: remove end_{queued|dequeued}_request()
  block: change elevator to use __blk_end_request()
  gdrom: change to use __blk_end_request()
  memstick: change to use __blk_end_request()
  virtio_blk: change to use __blk_end_request()
  blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
  block: add lld busy state exporting interface
  block: Fix blk_start_queueing() to not kick a stopped queue
  include blktrace_api.h in headers_install
  ...
2008-10-10 10:52:45 -07:00
Linus Torvalds
82219fceeb Merge branch 'upstream-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
  libata-eh: clear UNIT ATTENTION after reset
  ata_piix: add Hercules EC-900 mini-notebook to ich_laptop short cable list
  libata: reorder ata_device to remove 8 bytes of padding on 64 bits
  [libata] pata_bf54x: Add proper PM operation
  pata_sil680: convert CONFIG_PPC_MERGE to CONFIG_PPC
  libata: Implement disk shock protection support
  [libata] Introduce ata_id_has_unload()
  PATA: RPC now selects HAVE_PATA_PLATFORM for pata platform driver
  ata_piix: drop merged SCR access and use slave_link instead
  libata: implement slave_link
  libata: misc updates to prepare for slave link
  libata: reimplement link iterator
  libata: make SCR access ops per-link
2008-10-10 07:46:45 -07:00
Anton Vorontsov
4538d0ca71 powerpc: Fix no interrupt handling in pata_of_platform
When no interrupt is specified the pata_of_platform fills the irq_res
resource with -1, which is wrong to do for two reasons:

1. By definition, 'no irq' should be IRQ 0, not some negative integer;
2. pata_platform checks for irq_res.start > 0, but since irq_res.start
   is unsigned type, the check will be true for `-1'.

Reported-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-10 15:55:17 +11:00
Jens Axboe
8bff7c6b0f libata: set queue SSD flag for SSD devices
SSD devices should give an RPM setting of 1 in word 217 of the ID
page. If we see such a device, tell the block layer about it.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:19 +02:00
Jens Axboe
242f9dcb8b block: unify request timeout handling
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.

Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.

Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:13 +02:00