drivers/built-in.o: In function `pci_set_consistent_dma_mask':
hid-quirks.c:(.text+0x2664): multiple definition of `pci_set_consistent_dma_mask'
drivers/built-in.o: In function `pci_set_dma_mask':
hid-quirks.c:(.text+0x42c4): multiple definition of `pci_set_dma_mask'
because drivers/pci/pci.c was not seeing the definition disabling these
functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include <linux/i2c.h> in all ep93xx platforms.
Patch "5311/1: add core support for built in i2c bus" will cause build errors due to the following in
arch/arm/mach-ep93xx/include/mach/platform.h:
+void ep93xx_register_i2c(struct i2c_board_info *devices, int num);
The i2c.h header needs to be included in order to define struct i2c_board_info.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use EP93XX_*_PHYS_BASE and SZ_* defines in ep93xx platform inits.
The following patch changes the flash memory hard-coded resource
addresses and MACHINE_START boot_params to EP93XX_*_PHYS_BASE and
SZ_* defines to improve readability. Also some minor whitespace
cleanup resulting from previous patches.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The gpio setup for AM200 specific GPIO pins should be done in the AM200
code rather than in generic gumstix code.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dma_supported() is supposed to indicate whether the system can support
the DMA mask it was passed, which depends on the maximal address which
can be returned for DMA allocations. If the mask is smaller than that,
we are unable to guarantee that the driver can reliably obtain suitable
memory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Netwinder was using gpio_xxx names which could clash with the GPIO
layer. Add a 'nw_' prefix to ensure that these remain separate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Compilation for the Feroceon core should use -mtune=marvell-f. This is
available in Code Sourcery's 2008Q3 release at the moment. Otherwise
fall back to -mtune-=xscale.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
On newer versions of the RD88F6281 board, the WAN port is connected to
its own ethernet port on the CPU, via a separate PHY, whereas on older
versions of the board, it is connected to one of the PHYs in the
ethernet switch. In the RD8F6281 setup code, detect which version of
the board we are running on, and instantiate the ethernet ports and
switch driver accordingly.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The 88f6192 and 88f6281 Kirkwood SoCs support two ethernet ports.
Add the platform glue that will allow board support files to
instantiate the second ethernet port.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The 88F5182 found in the DNS-323 rev B1 (and some other devices, such
as the CH3SNAS) require different initialisation of the SATA
controller and MPP registers.
Tested on a DNS-323 rev B1.
Signed-off-by: Matt Palmer <mpalmer@hezmatt.org>
Based on similar code from the tsx09 series of machines, just rips the MAC
address out of flash and stuffs it into the NIC. Tested on a DNS323 rev B1.
It's possible (though unlikely) that an A1 will have the MAC in a different
location in flash.
Signed-off-by: Matt Palmer <mpalmer@hezmatt.org>
The Orion ehci driver serves the Orion, kirkwood and DD Soc families.
Since each of those integrate a different USB phy we should have the
ability to use few initialization sequences or to leave the boot loader
phy settings as is.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
Add Nuvoton W90X900 ARM9 plat support to linux arm tree,
Now, this patch include only W90P910 EVB of W90P910 CPU,
Its driver is nothing.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds HP iPAQ h5000's (h5400, h5500) basic definitions.
Kernel will able to boot, work via serial console, mount filesystems
placed on flashes and run USB gadgets (g_ether by default).
Other device drivers (frame buffer, LCD, touchscreen, backlight,
bluetooth, w1/battery, ...) are depend on SAMCOP and MediaQ
SoCs/MFDs, drivers to which will be submitted too, after massive
cleanups.
This machine will be used as "real user" for these new drivers.
This is an updated version of the patch, which contains fixes proposed on
linux-arm-kernel mailing list.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Milan Plzik <milan.plzik@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add platform data necessary to support tmiofb on tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Take advantage of the newly created wm97xx battery driver
and remove useless code in mioa701 board code. Add also the
ac connection detect capability after the matching gpio was
discovered.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The charger enable gpio is straight (1 means draw from USB
Vbus, 0 mean do not draw). The USB Vbus sensing is inverted
(1 means no Vbus voltage sensed, 0 means Vbus voltage
present).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Change the halt and reboot method from gpio based to "jump
to ROM IPL beginning". This gives control back to IPL, which
without PowerOn key pressed, will put the device into deep
sleep until PowerOn is pressed for 1 second.
But this has the benefit of keeping the RTC registers across
reboots, which is good for OS change.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add GPIO configuration and platform specific declarations
to make Mitac Mio A701 camera chip work. The chip is a
Micron MT9M111 CMOS sensor, based on PXA QIF interface and
I2C bus for sensor control.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Since mioa701 board has migrated to the mfp architecture,
low power gpio setup is now correctly handled even when gpio
led driver is not loaded, and leds and vibrator don't stay
activated in suspend mode (especially vibrator).
Remove the not needed anymore dependency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add IO memory and IRQ ressources for pxa based SoC to be
able to use the new rtc-pxa driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Following the removal of the "->policy" usage for PXA255 in patch
459fc208ab (cpufreq: remove
policy->governor setting in drivers initialization), this patch
introduces an option (called "pxa255_turbo_table") to select either
the "run" or "turbo" frequency table.
It also cures the runtime warning that was printed each time the
frequency was changed.
Got rid of all references to CPUFREQ_POLICY_* for pxa255, and sticked
with the run/turbo thing.
Tested on an Arcom/Eurotech Viper.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This symbol is required by locomo backlight driver, exporting this
allows the driver to be built as a module.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN
bit, add their definitions here with comments.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
PXA935 has changed its implementor ID from Intel to Marvell, this
patch modifies arch/arm/boot/compressed/head.S and proc-xsc3.S to
support a smooth bootup.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Let's put these devices into a central place even if they are now
processor specific, as they might be re-used in later processors.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
There two are internal registers that are used to control the power
management of the Internal Memory (i.e. Internal SRAM). They are
referenced nowhere and removed here to simplify pxa-regs.h a bit.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
We now have generic PWM API for PXA, the PWM registers definitions are
now used nowhere, and it is not encouraged to manipulate them directly
by driver code.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
pxa_gpio_{get,set}_value() are not used anymore, remove them from hardware.h.
Declaration of pxa_gpio_mode() is still being referenced and thus moved into
pxa2xx-gpio.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Original patch from Marek Vasut, the problems with PXA26x are:
1. there are additional 4 GPIOs 86,87,88,89 have their direction bits
inverted in GPDR2, as well as their alternate function bits being
'1' for their GPIO functionality in GAFRx
2. there is no easy way to decide if the processor is a pxa26x or a
pxa250/pxa255 at run-time, so the assumption here is the pxa26x
will be treated as one of the pxa25x variants, and board code
should have a better knowledge of the processor it is featured
Introduce pxa26x_init_irq() for the second purpose, and treat the
additional GPIOs > 85 on PXA25x specially.
Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code
a bit when PXA26x support isn't needed. Board config options have
to select this to enable the support for PXA26x.
__gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x
isn't selected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This reverts commit da1a3dc0eb.
The originally proposed way in the above commit is incorrect. And
there is no easy way to distinguish between pxa25x and pxa26x at
run-time.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we
already have that variable, remove the unnecessary 'gpio_nr' now.
Also, fix the incorrect GPIO number passed in pxa27x_init_irq().
Note: pxa_last_gpio should be initialized earlier, and this is true
since it's been assigned in machine_desc->init_irq().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA SoC have several GPIOs muxed on only one wakeup source.
Add support for these wakeup sources which were missing
in mfp core support.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The spi master driver must have num_chipselect set to allow the bus to
initialise. Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes bad formatting found in
mach-sa1100 files.
What it does is to replace/delete things like
excessive spaces (start || endline). The code
looks the same just alot less junk.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add debounce support for ep93xx gpio interrupts.
On the EP93xx, GPIO ports A, B, and F can be used to generate
interrupts. For each port, if interrupts are enabled, it is
possible to debouce the input signal. Debouncing is implemented
by passing the input signal through a 2-bit shift register clocked
by a 128Hz clock.
This patch adds a platform specific way to enable the debouce
feature for these input ports.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the ep93xx platform init code to register the built-in i2c bus.
The EP93xx processor has two GPIO pins dedicated for an I2C bus. This
patch registers the platform supplied i2c_board_info and the necessary
platform_device information for the i2c-gpio driver to use these pins.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Cirrus Logic EDB9307A Dev Board to arch/arm/mach-ep93xx
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91CAP9 revC CPU has a few differences over the previous,
revB CPU which was distributed in small quantities only (revA was
an internal Atmel product only).
This patch adds the detection routines to recognize the different
AT91CAP9 revisions (based on the PMC subsystem version number), and
uses them to:
- activate a workaround for the external interrupts levels
(on revB CPUs)
- set the UDPHS_BYPASS bit (on revB CPUs)
- set AT91_GPBR register address to the correct offset
(0xfffffd50 on revB, 0xfffffd60 on revC)
For debugging usage, the CPU revision can be found in /proc/cpuinfo
on the 'Revision' line.
This patch is extracted from Andrew Victor's -at91 patch (2.6.27-at91.patch)
where it has been tested for the last 6 months.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Adeneo NeoCore 926 board.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the SAM9 and CAP9 board-specific files to make use of the
sam9_smc_configure() method to configure the memory-controller for
external peripherals.
The following boards have been modified:
cam60 : NAND
cap9adk : NAND, NOR
qil-a9260 : NAND
sam9-l9260 : NAND
sam9260ek : NAND
sam9261ek : DM9000 Ethernet, NAND
sam9263 : NAND
sam9g20ek : NAND
sam9rlek : NAND
usb-a9260 : NAND
usb-a9263 .: NAND
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In at91_add_device_nand(), do not configure the Static Memory
controller with specific timing values.
The *_devices.c files are board independent, and the SMC timing values
are specific to the NAND devices that are installed on the board.
The board-specific files are now responsible for configuring the
Static Memory controller (if the don't want to leave it up to a
bootloader).
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a structure 'sam9_smc_config' and function sam9_smc_configure() to
allow the board-specific files to specify the configuration of the
Static Memory Controller per chip-select. This allows the board file
to specify timings for NAND flash, NOR flash or other external
peripherals.
This functionality can be used for all the SAM9 and CAP9 processors.
(the AT91RM9200 has a different memory-controller)
This patch is based on similar code in the AVR32 architecture.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This seems to be missing from the arm:devel branch, though the other
RealView configurations were modified accordingly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The original file was based on 2.6.19-rc3. Apart from the new symbols,
the explicitly enabled eatures are AEABI, REALVIEW_HIGH_PHYS_OFFSET and
MACH_REALVIEW_PB11MP.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The original file was based on 2.6.14-rc2. Apart from the new symbols,
the explicitly enabled features are AACI, MMC, AEABI,
MACH_REALVIEW_PB1176 and MACH_REALVIEW_PB11MP.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds smc911x.c device configuration to the RealView
platforms. At some point it may be changed to the new smsc911x.c driver
(once complete testing was done).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the Ethernet device registration from individual
realview_*.c files to core.c.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some of the calls weren't necessary and some others were duplicated.
This patch tidies up the platsmp.c file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
All the cases where the local timer for a CPU is accessed happen on the
corresponding current CPU, hence no need to access the per-CPU local
timer mappings.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the necessary definitions and Kconfig entries to enable
Cortex-A9 (ARMv7 SMP) tiles on the RealView/EB board.
Signed-off-by: Jon Callan <Jon.Callan@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The MCR for flushing the whole D cache is undefined on ARMv7 CPUs.
Signed-off-by: Harry Fearnhamm <Harry.Fearnhamm@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds support for RealView/PB-A8, a platform based on
Cortex-A8 with support for PCI-E and compact flash.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
RealView boards like PB11MPCore have 512MB of RAM available contiguously
at 0x70000000. Half of the memory is mirrored at 0x00000000 for
backwards compatibility. This patch adds the
CONFIG_REALVIEW_HIGH_PHYS_OFFSET option option to change the physical
base address so that the full amount of RAM is available to Linux. Note
that the EB board has 256MB of RAM also mirrored at 0x70000000, the only
board without this feature being PB1176.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Update to use the asm/sections.h header rather than declaring these
symbols ourselves. Change __data_start to _data to conform with the
naming found within asm/sections.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
lh7a40x only uses the clk API for the framebuffer, so there's
no point having a complicated implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
aaec2000 only uses the clk API for the framebuffer, so there's
no point having a complicated implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both of these symbols should be defined by a platform, or neither
should be defined. Ensure that all platforms conform.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RiscPC is the only platform using the default setting for NR_IRQS,
so the default NR_IRQS doesn't really make sense; remove it and
make RiscPC provide such a definition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since 8d5796d2ec, we have allowed
PAGE_OFFSET to be configurable, so a constant virtual address
for MAX_DMA_ADDRESS is buggy. It should be defined in terms of
PAGE_OFFSET rather than a constant virtual address.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definition of MAX_DMA_ADDRESS from mach/dma.h to mach/memory.h,
thereby placing it along side its relative, ISA_DMA_THRESHOLD.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
