Broken BIOS on Iwill 8way systems reports these and it causes the bootmem
allocator to crash. Add a sanity check if all the PXMs in the
SRAT table cover all memory as reported by e820. If the sanity
check fails the SRAT is rejected and the code will fall back
to discover the NUMA topology using the K8 northbridge registers
when applicable.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a new notifier chain that is called with IDLE_START
when a CPU goes idle and IDLE_END when it goes out of idle.
The context can be idle thread or interrupt context.
Since we cannot rely on MONITOR/MWAIT existing the idle
end check currently has to be done in all interrupt
handlers.
They were originally inspired by the similar s390 implementation.
They have a variety of applications:
- They will be needed for CONFIG_NO_IDLE_HZ
- They can be used for oprofile to fix up the missing time
in idle when performance counters don't tick.
- They can be used for better C state management in ACPI
- They could be used for microstate accounting.
This is just infrastructure so far, no users.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix off by one when checking if the machine has enougn memory to need IOMMU
This caused the IOMMUs to be needlessly enabled for mem=4G
Based on a patch from Jon Mason
Signed-off-by: jdmason@us.ibm.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whenever we see that a CPU is capable of C3 (during ACPI cstate init), we
disable local APIC timer and switch to using a broadcast from external timer
interrupt (IRQ 0).
Patch below adds the code for x86_64.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whenever we see that a CPU is capable of C3 (during ACPI cstate init), we
disable local APIC timer and switch to using a broadcast from external timer
interrupt (IRQ 0). This is needed because Intel CPUs stop the local
APIC timer in C3. This is currently only enabled for Intel CPUs.
Patch below adds the code for i386 and also the ACPI hunk.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the finer control of local APIC timer. We cannot provide a sub-jiffy
control like this when we use broadcast from external timer in place of
local APIC. Instead of removing this only on systems that may end up using
broadcast from external timer (due to C3), I am going the
"I'm feeling lucky" way to remove this fully. Basically, I am not sure about
usefulness of this code today. Few other architectures also don't seem to
support this today.
If you are using profiling and fine grained control and don't like this going
away in normal case, yell at me right now.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I would like to throw out a suggestion for a possible change in the way that
the debug register traps are handled in do_debug() when the trap occurs
in kernel-mode.
In the x86_64 version of do_debug(), the code will skip around sending
a SIGTRAP to the current task if the trap occurred while in kernel mode.
On the i386-side of things, if the access happens to occur in kernel mode
(say during a read(2) of user's buffer that matches the address of a
debug register trap), then the do_debug() routine for i386 will go ahead
and call send_sigtrap() and send the SIGTRAP signal. The send_sigtrap()
code will also set the info.si_addr to NULL in this case (even though I
don't understand why, since the SIGTRAP siginfo processing doesn't use
the si_addr field...).
So I would like to suggest that the x86_64 do_debug() routine also
follow this type of behavior and have it go ahead and send the
SIGTRAP signal to the current task, even if the debug register trap
happens to have occurred in kernel mode. I have taken a stab at
a patch for this change below. (It includes the i386-ish change
for setting si_addr to NULL when the trap occurred in kernel mode.)
It seems like a useful feature to be able to 'watch' a user location that
might also be modified in the kernel via a system service call, and have the
debugger report that information back to the user, rather than to just
silently ignore the trap.
Additionally, I realize that users that pull in a kernel debugger such as
KGDB into their kernel might want to remove this change below when they add
in KGDB support. However, they could alternatively look at the current
task's thread.debugreg[] values to see if the trap occurred due to KGDB
or instead because of a user-space debugger trap, and still honor the
user SIGTRAP processing (instead of the KGDB breakpoint processing)
if the trap matches up with the thread.debugreg[] registers.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Much better to deal with these than with the magic numbers.
And remove the comment describing the bits - kernel source
is no replacement for an architecture manual.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't need to do the vmalloc check for the module range because its
PML4 is shared with the kernel text.
Also removed an unnecessary TLB flush.
Pointed out by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is on the same lines as Zachary Amsden's i386 GDT page alignemnt
patch in -mm, but for x86_64.
Patch to align and pad x86_64 GDT on page boundries.
[AK: some minor cleanups and fixed incorrect TLS initialization
in CPU init.]
Signed-off-by: Nippun Goel <nippung@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This might help on distributions that use a 32bit biarch compiler.
First pass -m64 by default.
Secondly add some more .code32s because at least the Ubuntu biarch
32bit as called by gcc doesn't seem to handle -m64 -m32 as generated
by the Makefile without such assistance.
And finally make sure the linker script can be preprocessed
with a 32bit cpp.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attempt to avoid overflow in __delay caused varying precision
on different CPUs depending on differences in the CPU speed.
We should be able to do this multiplication with out overflowing
provided the
cpu is running at less than about 128 GHz. xloops < 20000 * 0x10c6.
loops_per_jiffy * HZ <= cpu_clock_speed. So if the cpu clock speed
< 2^64/(20000 * 0x10c6) = 2^64/ 51E6CC0 < 2^64/2^27 = 2^37 = 128G we
will not overflow the calculation.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we don't know the node a PCI bus is connected to return -1.
This matches the generic code.
Noticed by Ravikiran G Thirumalai <kiran@scalex86.org>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of Opteron BIOS just pass 10 in all SLIT entries (10 is the
normalized unit). This is actually worse than the default heuristic
because it leads to pci_distance not knowing the difference between
local and remote nodes anymore. This messes up some NUMA
heuristics in generic code.
In this case it's better to fall back to the default heuristic
which just does nodea == nodeb ? 10 : 20.
This patch does some basic sanity checking on the SLIT and only accepts
the SLIT when it passes.
Invariants enforced are:
- Node to itself shall be 10
- Any other distance shouldn't be 10
- Distances smaller than 10 are illegal
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some people need it now on 64bit so reuse the i386 code for
x86-64. This will be also useful for future bug workarounds.
It is a bit simplified there because there is no need
to do it very early on x86-64. This means it doesn't need
early ioremap et.al. We run it as a core initcall right now.
I hope it's not needed for early setup.
I added a general CONFIG_DMI symbol in case IA64 or someone
else wants to reuse the code later too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was a backup file that somehow made it into the official
tree. Never used for anything. Remove.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The introduction of call_softirq switching to the interrupt stack several
releases earlier resulted in a problem with the code in show_trace, which
assumes that it can pick the previous stack pointer from the end of the
interrupt stack.
Cc: Andi Kleen <ak@muc.de>
Cc: Arjan van de Ven <arjanv@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Be more careful with TF handling to fix some copy protection codes in wine
patch originally for i386 by Linus, then ported to x86_64 by Andi Kleen
see: [PATCH] x86_64: Some fixes for single step handling
commit: be61bff789
But it was never applied to the ia32 emulation code which breaks some
copy-protection schemes under wine when running on x86_64.
Signed-off-by: Peter Beutner <p.beutner@gmx.net>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So why are we calling smp_send_stop from machine_halt?
We don't.
Looking more closely at the bug report the problem here
is that halt -p is called which triggers not a halt but
an attempt to power off.
machine_power_off calls machine_shutdown which calls smp_send_stop.
If pm_power_off is set we should never make it out machine_power_off
to the call of do_exit. So pm_power_off must not be set in this case.
When pm_power_off is not set we expect machine_power_off to devolve
into machine_halt.
So how do we fix this?
Playing too much with smp_send_stop is dangerous because it
must also be safe to be called from panic.
It looks like the obviously correct fix is to only call
machine_shutdown when pm_power_off is defined. Doing
that will make Andi's assumption about not scheduling
true and generally simplify what must be supported.
This turns machine_power_off into a noop like machine_halt
when pm_power_off is not defined.
If the expected behavior is that sys_reboot(LINUX_REBOOT_CMD_POWER_OFF)
becomes sys_reboot(LINUX_REBOOT_CMD_HALT) if pm_power_off is NULL
this is not quite a comprehensive fix as we pass a different parameter
to the reboot notifier and we set system_state to a different value
before calling device_shutdown().
Unfortunately any fix more comprehensive I can think of is not
obviously correct. The core problem is that there is no architecture
independent way to detect if machine_power will become a noop, without
calling it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed that some lowlevel send_IPI_mask helpers had a hotplug/preempt
race whereupon the cpu_online_map was read before disabling preemption;
...
cpumask_t mask = cpu_online_map;
int cpu = get_cpu();
cpu_clear(cpu, mask);
...
But then i realised that there is no need for these lowlevel functions to
be going through all this trouble when all the callers are already made
hotplug/preempt safe.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is one CPU here whose MCE bank count is 6. This patch increases
x86_64's MCE bank count.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following is probably a good idea given that the atomic_set() isn't
a barrier here either.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This
- switches the INT3 handler to run on an IST stack (to cope with
breakpoints set by a kernel debugger on places where the kernel's
%gs base hasn't been set up, yet); the IST stack used is shared with
the INT1 handler's
[AK: this also allows setting a kprobe on the interrupt/exception entry
points]
- allows nesting of INT1/INT3 handlers so that one can, with a kernel
debugger, debug (at least) the user-mode portions of the INT1/INT3
handling; the nesting isn't actively enabled here since a kernel-
debugger-free kernel doesn't need it
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Print bits for RDTSCP, SVM, CR8-LEGACY.
Also now print power flags on i386 like x86-64 always did.
This will add a new line in the 386 cpuinfo, but that shouldn't
be an issue - did that in the past too and I haven't heard
of any breakage.
I shrunk some of the fields in the i386 cpuinfo_x86 to chars
to make up for the new int "x86_power" field. Overall it's
smaller than before.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They previously tried to figure this out on their own.
Suggested by Venkatesh.
Cc: venkatesh.pallipadi@intel.com
Cc: davej@redhat.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define it for i386 too.
This is a synthetic flag that signifies that the CPU's TSC runs
at a constant P state invariant frequency.
Fix up the logic on x86-64/i386 to set it on all known CPUs.
Use the AMD defined bit to set it on future AMD CPUs.
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Was only used by the floppy driver to work around some ancient
hardware bug that should never occur on any 64bit system.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most users don't need it so no need to waste memory.
This means an user has to specify the appropiate number of
hotplug CPUs on the command line with additional_cpus=...
or fix their BIOS to follow the convention in
Documentation/x86-64/cpu-hotplug-spec
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adjust page fault protection error check before considering it to be
a vmalloc synchronization candidate.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure no iret can fault without attached recovery code.
Cannot happen in the normal case, but might be useful
with kernel debuggers
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since a double fault always implies that kernel data structures are
corrupt, this fault should neither be handed to user mode handling,
nor should the handler allow resuming the faulting code stream (since
architecturally this isn't a fault, but an abort).
Note that this slightly depends on the previously submitted patch
adjusting the prototype of notify_die() (a compiler warning will result
without that other patch).
AK: Removed obsolete CONFIG_CHECKING code, added comments
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adjusts things so that handlers of the die() notifier will have
sufficient information about the trap currently being handled. It also
adjusts the notify_die() prototype to (again) match that of i386.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Other than apparently commonly assumed, the bound instruction does not
require the corresponding IDT entry to have DPL 3.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a follow-up to the introduction of CONFIG_UNWIND_INFO, this
separates the generation of frame unwind information for x86-64 from
that of full debug information.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on the documentation recently posted by Richard Brunner.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Frame unwind information was still incorrect for ia32_ptregs_common
(sorry, my fault), and could be improved for some of the other entry
points.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a window where a probe gets removed right after the probe is hit
on some different cpu. In this case probe handlers can't find a matching
probe instance related to break address. In this case we need to read the
original instruction at break address to see if that is not a break/int3
instruction and recover safely.
Previous code had a bug where we were not checking for the above race in
case of reentrant probes and the below patch fixes this race.
Tested on IA64, Powerpc, x86_64.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The HDIO_GETGEO patch left an unused variable in the UML block driver. This
gets rid of it.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The debug-stub patch was broken on x86_64 because it thinks the frame size
there is 168 words. In reality, it is 168 bytes, and using HOST_FRAME_SIZE,
which is expressed in consistent units across architectures, fixes this.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CON_PRINTBUFFER was a bad idea for the mconsole console. It causes the boot
output to be printed twice.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Undo the previous no-modes patch since Adrian Bunk sent in a kbuild way of
doing the same thing.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The MODE_TT help was a little outdated. This updates it in light of the
existence of skas0 mode. It's also turned off by default since it is mostly
obsoleted by skas0 mode.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.15-mm1 caused kernel-offsets.c to stop compiling with a syntax error in a
header. The problem was with KBUILD_BASENAME, which didn't get a definition
with the by-hand compilation in the main UML Makefile.
This was OK before since the expansion was syntactically the same as the
KBUILD_BASENAME token. With -mm1, the expansion is now a quote-delimited
string, so there needs to be a definition of it.
Since kernel-offsets.c is basically the same as other arches' asm-offsets.c,
and those seem to build OK, this patch turns kernel-offsets.c into
asm-offsets.c. kernel-offsets.c is in arch/um/sys-$(SUBARCH), i.e. sys-i386
and sys-x86_64, while kbuild expects it to be in arch/um/kernel.
kernel-offsets.c is moved to
arch/um/include/sysdep-$(SUBARCH)/kernel-offsets.h, which is included by
arch/um/kernel/asm-offsets.c. With that, include/asm-um/asm-offsets.h is
generated automatically. kernel-offsets.h continues to exist because it needs
to be accessible to userspace UML code, and include/asm-um isn't. So, a
symlink is made from arch/um/include/kernel-offsets.h to
include/asm-um/asm-offsets.h.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo in the dependencies of HUGETLB_PAGE_SIZE_64K.
It might be more logical to rename the HUGETLB_PAGE_SIZE_*K
dependencies to HUGETLB_PAGE_SIZE_*KB, but let's fix this bug first.
This bug was reported by Jean-Luc Leger <reiga@dspnet.fr.eu.org>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's switch mutex_debug_check_no_locks_freed() to take (addr, len) as
arguments instead, since all its callers were just calculating the 'to'
address for themselves anyway... (and sometimes doing so badly).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/powerpc/kernel/crash.c isn't safe for PPC32 (yet?), so don't build it.
Built with CONFIG_KEXEC=y for pmac32_defconfig, pseries_defconfig,
and g5_defconfig.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
clean-files was being set twice rather than being appended to.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Removing the dependency on the boot image build was good, but it also
meant that the $< expansion by make needed to be done explicitly.
Noted by Stephen Hemminger.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
iSeries doesn't need to set the htab_address explicitly, htab_initialize()
will do it for us later.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To make iSeries just a teensy bit less special, create ibm,pft-size properties
in the iSeries device tree. We can then rely on htab_dt_scan_pftsize() to set
ppc64_pft_size for us.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated Kconfig & Makefiles in prep for adding support for the Freescale
MPC83xx family of processors to arch/powerpc. Moved around some config
options that are more globally applicable to other PowerPC processors.
Added a temporary config option (83xx) to match existing arch/ppc support
for the MPC83xx line.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPE Book IV indicates that MFC DMA operations must be
suspended and restored on SPU context switch (in Step 8).
This patch adds that operation, which is missing from the
current spufs implementation.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes the compilation error (shown below) when CONFIG_SMP=n.
arch/powerpc/kernel/crash.c: In function `crash_kexec_prepare_cpus':
arch/powerpc/kernel/crash.c:236: error: implicit declaration of
function `smp_release_cpus'
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current ppc64 per cpu data implementation is quite slow. eg:
lhz 11,18(13) /* smp_processor_id() */
ld 9,.LC63-.LCTOC1(30) /* per_cpu__variable_name */
ld 8,.LC61-.LCTOC1(30) /* __per_cpu_offset */
sldi 11,11,3 /* form index into __per_cpu_offset */
mr 10,9
ldx 9,11,8 /* __per_cpu_offset[smp_processor_id()] */
ldx 0,10,9 /* load per cpu data */
5 loads for something that is supposed to be fast, pretty awful. One
reason for the large number of loads is that we have to synthesize 2
64bit constants (per_cpu__variable_name and __per_cpu_offset).
By putting __per_cpu_offset into the paca we can avoid the 2 loads
associated with it:
ld 11,56(13) /* paca->data_offset */
ld 9,.LC59-.LCTOC1(30) /* per_cpu__variable_name */
ldx 0,9,11 /* load per cpu data
Longer term we can should be able to do even better than 3 loads.
If per_cpu__variable_name wasnt a 64bit constant and paca->data_offset
was in a register we could cut it down to one load. A suggestion from
Rusty is to use gcc's __thread extension here. In order to do this we
would need to free up r13 (the __thread register and where the paca
currently is). So far Ive had a few unsuccessful attempts at doing that :)
The patch also allocates per cpu memory node local on NUMA machines.
This patch from Rusty has been sitting in my queue _forever_ but stalled
when I hit the compiler bug. Sorry about that.
Finally I also only allocate per cpu data for possible cpus, which comes
straight out of the x86-64 port. On a pseries kernel (with NR_CPUS == 128)
and 4 possible cpus we see some nice gains:
total used free shared buffers cached
Mem: 4012228 212860 3799368 0 0 162424
total used free shared buffers cached
Mem: 4016200 212984 3803216 0 0 162424
A saving of 3.75MB. Quite nice for smaller machines. Note: we now have
to be careful of per cpu users that touch data for !possible cpus.
At this stage it might be worth making the NUMA and possible cpu
optimisations generic, but per cpu init is done so early we have to be
careful that all architectures have their possible map setup correctly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds Kconfig entries to control the early debugging options,
currently in setup_64.c.
Doing this via Kconfig rather than #defines means you can have one source tree,
which is buildable for multiple platforms - and you can enable the correct
early debug option for each platform via .config.
I made udbg_early_init() a static inline because otherwise GCC is to daft to
optimise it away when debugging is off.
Now that we have udbg_init_rtas() we can make call_rtas_display_status* static.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Connect iSeries up to the standard early debugging infrastructure.
To actually use this you need to enable the iSeries early debugging
in setup_64.c. Then after the messages are logged hit Ctrl-x Ctrl-x on
your console to dump the Hypervisor console buffer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RPAPHP hoplug driver will not build as a module, because it calls
on a pcibios routine which is not exported. This exports the symbol.
Problem reported by Olaf Hering <olh@suse.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup vmlinux.lds.S by using STABS_DEBUG macro from vmlinux.lds.h
instead of repeating the sections.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix Dino reporting on J2240. This particular machine thought it
had a Cujo. Also add J2240 Dino chip to the hp_hardware_list.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
max_low_pfn was not being set in arch/parisc/mm/init.c, causing severe
problems whenever anything tried to use BLK_BOUNCE_HIGH. Set it to
max_pfn like other similar architectures do.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make knapps work with its 64MB gfx card. I probably just broke another
machine in the process, but assuming 64MB when 64MB aligned is probably
safer than assuming 32MB all the time.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fixup ioremap a bit. It seems to work on 32-bit kernels, but fails
miserably on the first ioremapped access on 64-bit kernels. Also, having
STI enabled causes it to fail. Probably because we're passing an ioremapped
region to a real-mode STI call...
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make flush_data_cache_local, flush_instruction_cache_local and
flush_tlb_all_local take a void * so they don't have to be cast
when using on_each_cpu(). This becomes a problem when on_each_cpu
is a macro (as it is in current -mm).
Also move the prototype of flush_tlb_all_local into tlbflush.h and
remove its declaration from .c files.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Flag a whole bunch of things as __read_mostly on parisc. Also flag a few
branches as unlikely() and cleanup a bit of code.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Adjust length of M5208EVB ram define. It should size up to 32MB after
adding in the dBUG reserved 128k.
Problem pointed out be Milton Miller <miltonm@bga.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch adapted from a posting by Andrea Tarani which was
pointed out to me by Bernardo Innocenti. Thanks to both of them for
their help and patience.
The original posting is here:
http://mailman.uclinux.org/pipermail/uclinux-dev/2005-July/033543.html
The problem first manifest itself as busybox ping terminating with an
"Illegal instruction". I reduced this to a test case and found that
variable size arrays allocated on the stack could lead to stacks not
aligned on 32 bit boundaries. For the Coldfire this proved fatal.
Having been pointed out this patch by Bernardo, I applied it and it
fixed the first test case. I then went back to busybox's ping. This
still failed with "Illegal instruction", but in a different way. Before
it depended on the size allocated for the ping buffer, now it happened
every time. I also found it depended on optimisation level (gcc-3.4.0)
-Os was okay but not -O2.
After a lot of looking, it turned out that register a5 was being
corrupted by the signal handler (after applying the patch). I re-worked
the patch a bit to save/restore a5 and now all seems well.
Patch submitted by Stuart Hughs <stuarth@freescale.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't specify compiler optimization flags in the m68knommu Makefile.
Let the top level Makefile/config set it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
#3244)
Patch from Andrew Victor
This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.
This patch is the support for the Cogent CSB337 and CSB637 boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.
This patch is the support for Atmel's DK and EK boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The API and code have been through various bits of initial review by
serial driver people but they definitely need to live somewhere for a
while so the unconverted drivers can get knocked into shape, existing
drivers that have been updated can be better tuned and bugs whacked out.
This replaces the tty flip buffers with kmalloc objects in rings. In the
normal situation for an IRQ driven serial port at typical speeds the
behaviour is pretty much the same, two buffers end up allocated and the
kernel cycles between them as before.
When there are delays or at high speed we now behave far better as the
buffer pool can grow a bit rather than lose characters. This also means
that we can operate at higher speeds reliably.
For drivers that receive characters in blocks (DMA based, USB and
especially virtualisation) the layer allows a lot of driver specific
code that works around the tty layer with private secondary queues to be
removed. The IBM folks need this sort of layer, the smart serial port
people do, the virtualisers do (because a virtualised tty typically
operates at infinite speed rather than emulating 9600 baud).
Finally many drivers had invalid and unsafe attempts to avoid buffer
overflows by directly invoking tty methods extracted out of the innards
of work queue structs. These are no longer needed and all go away. That
fixes various random hangs with serial ports on overflow.
The other change in here is to optimise the receive_room path that is
used by some callers. It turns out that only one ldisc uses receive room
except asa constant and it updates it far far less than the value is
read. We thus make it a variable not a function call.
I expect the code to contain bugs due to the size alone but I'll be
watching and squashing them and feeding out new patches as it goes.
Because the buffers now dynamically expand you should only run out of
buffering when the kernel runs out of memory for real. That means a lot of
the horrible hacks high performance drivers used to do just aren't needed any
more.
Description:
tty_insert_flip_char is an old API and continues to work as before, as does
tty_flip_buffer_push() [this is why many drivers dont need modification]. It
does now also return the number of chars inserted
There are also
tty_buffer_request_room(tty, len)
which asks for a buffer block of the length requested and returns the space
found. This improves efficiency with hardware that knows how much to
transfer.
and tty_insert_flip_string_flags(tty, str, flags, len)
to insert a string of characters and flags
For a smart interface the usual code is
len = tty_request_buffer_room(tty, amount_hardware_says);
tty_insert_flip_string(tty, buffer_from_card, len);
More description!
At the moment tty buffers are attached directly to the tty. This is causing a
lot of the problems related to tty layer locking, also problems at high speed
and also with bursty data (such as occurs in virtualised environments)
I'm working on ripping out the flip buffers and replacing them with a pool of
dynamically allocated buffers. This allows both for old style "byte I/O"
devices and also helps virtualisation and smart devices where large blocks of
data suddenely materialise and need storing.
So far so good. Lots of drivers reference tty->flip.*. Several of them also
call directly and unsafely into function pointers it provides. This will all
break. Most drivers can use tty_insert_flip_char which can be kept as an API
but others need more.
At the moment I've added the following interfaces, if people think more will
be needed now is a good time to say
int tty_buffer_request_room(tty, size)
Try and ensure at least size bytes are available, returns actual room (may be
zero). At the moment it just uses the flipbuf space but that will change.
Repeated calls without characters being added are not cumulative. (ie if you
call it with 1, 1, 1, and then 4 you'll have four characters of space. The
other functions will also try and grow buffers in future but this will be a
more efficient way when you know block sizes.
int tty_insert_flip_char(tty, ch, flag)
As before insert a character if there is room. Now returns 1 for success, 0
for failure.
int tty_insert_flip_string(tty, str, len)
Insert a block of non error characters. Returns the number inserted.
int tty_prepare_flip_string(tty, strptr, len)
Adjust the buffer to allow len characters to be added. Returns a buffer
pointer in strptr and the length available. This allows for hardware that
needs to use functions like insl or mencpy_fromio.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the serial driver to remove flip buffers have broken the serial
jsm driver. It doesn't even compile anymore. The jsm driver was enabled
in only one defconfig - ppc64. In order to keep defconfigs building,
disable CONFIG_SERIAL_JSM for the time being.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Bugzilla Bug 5351
"After resuming from S3 (suspended while in X), the LCD panel stays black .
However, the laptop is up again, and I can SSH into it from another
machine.
I can get the panel working again, when I first direct video output to the
CRT output of the laptop, and then back to LCD (done by repeatedly hitting
Fn+F5 buttons on the Toshiba, which directs output to either LCD, CRT or
TV) None of this ever happened with older kernels."
This bug is due to the recently added vesafb_blank() method in vesafb. It
works with CRT displays, but has a high incidence of problems in laptop
users. Since CRT users don't really get that much benefit from hardware
blanking, drop support for this.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch (against 2.6.15-rc5-mm3) fixes a kprobes build break
due to changes introduced in the kprobe locking in 2.6.15-rc5-mm3. In
addition, the patch reverts back the open-coding of kprobe_mutex.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently arch_remove_kprobes() is only implemented/required for x86_64 and
powerpc. All other architecture like IA64, i386 and sparc64 implementes a
dummy function which is being called from arch independent kprobes.c file.
This patch removes the dummy functions and replaces it with
#define arch_remove_kprobe(p, s) do { } while(0)
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on some feedback from Oleg Nesterov, I have made few changes to
previously posted patch.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since Kprobes runtime exception handlers is now lock free as this code path is
now using RCU to walk through the list, there is no need for the
register/unregister{_kprobe} to use spin_{lock/unlock}_isr{save/restore}. The
serialization during registration/unregistration is now possible using just a
mutex.
In the above process, this patch also fixes a minor memory leak for x86_64 and
powerpc.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- introduce ktime_t: nanosecond-resolution time format.
- eliminate the plain s64 scalar type, and always use the union.
This simplifies the arithmetics. Idea from Roman Zippel.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days ioctl32.h is only used for communication of fs/compat.c and
fs/compat_ioctl.c and doesn't contain anything of interest to drivers.
Remove inclusion in various drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that all these entries in the arch ioctl32.c files are gone [1], we can
build fs/compat_ioctl.c as a normal object and kill tons of cruft. We need a
special do_ioctl32_pointer handler for s390 so the compat_ptr call is done.
This is not needed but harmless on all other architectures. Also remove some
superflous includes in fs/compat_ioctl.c
Tested on ppc64.
[1] parisc still had it's PPP handler left, which is not fully correct
for ppp and besides that ppp uses the generic SIOCPRIV ioctl so it'd
kick in for all netdevice users. We can introduce a proper handler
in one of the next patch series by adding a compat_ioctl method to
struct net_device but for now let's just kill it - parisc doesn't
compile in mainline anyway and I don't want this to block this
patchset.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a compat_ioctl method to the dasd driver so the last entries in
arch/s390/kernel/compat_ioctl.c can go away. Unlike the previous attempt this
one does not replace the ioctl method with an unlocked_ioctl method so that
the ioctl_by_bdev calls in s390 partition code continue to work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements generic handling of RTC_IRQP_READ32, RTC_IRQP_SET32,
RTC_EPOCH_READ32 and RTC_EPOCH_SET32 in fs/compat_ioctl.c. It's based on the
x86_64 code which needed a little massaging to be endian-clean.
parisc used COMPAT_IOCTL or generic w_long handlers for these whichce is wrong
and can't work because the ioctls encode sizeof(unsigned long) in their ioctl
number. parisc also duplicated COMPAT_IOCTL entries for other rtc ioctls
which I remove in this patch, too.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment in compat.c is wrong, every architecture provides a
get_compat_sigevent() for the IPC compat code already.
This basically moves the x86_64 version to common code and removes all the
others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only own ioctl, TAPE390_DISPLAY, is compat_clean, everything else is
routed through common translation code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These ioctls are definitely not compat clean, but we already have a proper
handler in common code, over-riding it in architecture code is
counter-productive.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Again easy because all ioctls are compat clean.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have heard some complaints about people not finding CONFIG_CRASH_DUMP
option and also some objections about its dependency on CONFIG_EMBEDDED.
The following patch ends that dependency. I thought of hiding it under
CONFIG_KEXEC, but CONFIG_PHYSICAL_START could also be used for some reasons
other than kexec/kdump and hence left it visible. I will also update the
documentation accordingly.
o Following patch removes the config dependency of CONFIG_PHYSICAL_START
on CONFIG_EMBEDDED. The reason being CONFIG_CRASH_DUMP option for
kdump needs CONFIG_PHYSICAL_START which makes CONFIG_CRASH_DUMP depend
on CONFIG_EMBEDDED. It is not always obvious for kdump users to choose
CONFIG_EMBEDDED.
o It also shifts the palce where this option appears, to make it closer
to kexec and kdump options.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Moving the crash_dump.c file to arch dependent part as kmap_atomic_pfn is
specific to i386 and highmem may not exist in other archs.
- Use ioremap for x86_64 to map the previous kernel memory.
- In copy_oldmem_page(), we now directly copy to the user/kernel buffer and
avoid the unneccesary copy to a kmalloc'd page.
Signed-off-by: Rachita Kothiyal <rachita@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Saving the cpu registers of all cpus before booting in to the crash
kernel.
- crash_setup_regs will save the registers of the cpu on which panic has
occured. One of the concerns ppc64 folks raised is that after capturing the
register states, one should not pop the current call frame and push new one.
Hence it has been inlined. More call frames later get pushed on to stack
(machine_crash_shutdown() and machine_kexec()), but one will not want to
backtrace those.
- Not very sure about the CFI annotations. With this patch I am getting
decent backtrace with gdb. Assuming, compiler has generated enough
debugging information for crash_kexec(). Coding crash_setup_regs() in pure
assembly makes it tricky because then it can not be inlined and we don't
want to return back after capturing register states we don't want to pop
this call frame.
- Saving the non-panicing cpus registers will be done in the NMI handler
while shooting down them in machine_crash_shutdown.
- Introducing CRASH_DUMP option in Kconfig for x86_64.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Vivek Goyal <vgoyal@in.ibm.com>
- Implementing the machine_crash_shutdown for x86_64 which will be called by
crash_kexec (called in case of a panic, sysrq etc.). Here we do things
similar to i386. Disable the interrupts, shootdown the cpus and shutdown
LAPIC and IOAPIC.
Changes in this version:
- As the Eric's APIC initialization patches are reverted back, reintroducing
LAPIC and IOAPIC shutdown.
- Added some comments on CPU hotplug, modified code as suggested by Andi
kleen.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- elfcorehdr= specifies the location of elf core header stored by the
crashed kernel. This command line option will be passed by the kexec-tools
to capture kernel.
Changes in this version :
- Added more comments in kernel-parameters.txt and in code.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Vivek Goyal <vgoyal@in.ibm.com>
- This patch introduces the memmap option for x86_64 similar to i386.
- memmap=exactmap enables setting of an exact E820 memory map, as specified
by the user.
Changes in this version:
- Used e820_end_of_ram() to find the max_pfn as suggested by Andi kleen.
- removed PFN_UP & PFN_DOWN macros
- Printing the user defined map also.
Signed-off-by: Murali M Chakravarthy <muralim@in.ibm.com>
Signed-off-by: Hariprasad Nellitheertha <nharipra@gmail.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- If system panics then cpu register states are captured through funciton
crash_get_current_regs(). This is not a inline function hence a stack frame
is pushed on to the stack and then cpu register state is captured. Later
this frame is popped and new frames are pushed (machine_kexec).
- In theory this is not very right as we are capturing register states for a
frame and that frame is no more valid. This seems to have created back
trace problems for ppc64.
- This patch fixes it up. The very first thing it does after entering
crash_kexec() is to capture the register states. Anyway we don't want the
back trace beyond crash_kexec(). crash_get_current_regs() has been made
inline
- crash_setup_regs() is the top architecture dependent function which should
be responsible for capturing the register states as well as to do some
architecture dependent tricks. For ex. fixing up ss and esp for i386.
crash_setup_regs() has also been made inline to ensure no new call frame is
pushed onto stack.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- In case of system crash, current state of cpu registers is saved in memory
in elf note format. So far memory for storing elf notes was being allocated
statically for NR_CPUS.
- This patch introduces dynamic allocation of memory for storing elf notes.
It uses alloc_percpu() interface. This should lead to better memory usage.
- Introduced based on Andi Kleen's and Eric W. Biederman's suggestions.
- This patch also moves memory allocation for elf notes from architecture
dependent portion to architecture independent portion. Now crash_notes is
architecture independent. The whole idea is that size of memory to be
allocated per cpu (MAX_NOTE_BYTES) can be architecture dependent and
allocation of this memory can be architecture independent.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Vivek Goyal <vgoyal@in.ibm.com>
This patch fixes a minor bug based on Andi Kleen's suggestion. asm's can't be
broken in this particular case, hence merging them.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Adrian Bunk <bunk@stusta.de>
- create one common dump_thread() prototype in kernel.h
- dump_thread() is only used in fs/binfmt_aout.c and can therefore be
removed on all architectures where CONFIG_BINFMT_AOUT is not
available
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Especially useful when users have booted with 'quiet'. In the regular 'oops'
path, we set the console_loglevel before we start spewing debug info, but we
can call the backtrace code from other places now too, such as the spinlock
debugging code.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems the "make UID16 support optional" patch was checked when it
edited the -tiny tree some time ago, but it wasn't checked whether it
still matches the current situation when it was submitted for inclusion
in -mm. This patch fixes the following bugs:
- ARCH_S390X does no longer exist, nowadays this has to be expressed
through (S390 && 64BIT)
- in five architecture specific Kconfig files the UID16 options
weren't removed
Additionally, it changes the fragile negative dependencies of UID16 to
positive dependencies (new architectures are more likely to not require
UID16 support).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... giving those with with R1 or older CPU cards more rope to
missconfigure their kernels. But MIPS is only selling R2 CPUs since
two or three years already.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This was a stop gap meassure for gcc 3.3 and newer sometimes not inlining
inline functions in the 2.4 days. Starting we pass the always_inline
attribute, so -finline-limit is no longer necessary and it's been shown
to problematic on Sparc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
dump_regs() is used by a bunch of drivers for their internal stuff;
renamed mips instance (one that is seen in system-wide headers)
to elf_dump_regs()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
used_dsp was meant to be used like used_math - but since the FPU context
is small and lazy context switching is a stupid idea on multiprocessors
this idea only got halfway implemented and those bits are were now
breaking ptrace.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds back the call to pci_cfg_space_size() when building the PCI
tree from OF nodes that was commented out due to the function not being
exported by the PCI code. It's now exported, so let's use it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Matthew Wilcox wondered why we need these functions. We don't.
Remove them and just use the "normal" versions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous change by Kumar Gala in this area led to legacy_serial.c
and udbg_16550.c being built as modules when CONFIG_SERIAL_8250=m.
Fix this by introducing a new symbol, CONFIG_PPC_UDBG_16550, to
control whether these files get built, and arrange for it to be selected
for those platforms that need it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a crash on null-pointer deref during dlpar slot addition.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 1c87c0f84943fbbc91826967ff4fea1b059a526f commit)
<asm/systemcfg.h> is gone now, and the PCI error recovery constants
in include/linux/pci.h changed their names in the process of getting
accepted.
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 5a2516156c591fc3d2059fbd93f97e15eb6010d6 commit)
242-eeh-no-percpu-counters.patch
Remove per-cpu counters from the EEH code. These statistics counters
are incremented at a very low frequency, and the performance gains of
per-cpu variables are negligable. By contrast, the counters weren't
safe against cpu off/online operations, and its not worth the effort
to make them so (other than to turn them into plain globals).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from be3b5d1be053ccb41e91fa5a6f43ef5db301357d commit)
241-eeh-save-bars-earlier.patch
Save the PCI device bars *before* any PCI probing is done.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 76c902b919098860f3d4e125f847abcc4cb1782a commit)
240-ioremap-null-ptr-test.patch
Under highly unusual circumstances, a buggy driver will ask a null ptr
to be ioremapped, an operation that curently succeeds but leads to
later trouble. Instead, refuse to remap the null pointer.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e71d9e598533c1889e7162f5f4647e5d378c102c commit)
239-eeh-multifunction-consolidate.patch
New-style firmware will often place multiple different functions
under a non-EEH-aware parent. However, these devices might share
a common PE "partition endpoint" and config address, ad thus any
EEH events will affect all of the devices in common. This patch
makes the effort to find all of these common devices and handle
them together.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 216810296bb97d39da8e176822e9de78d2f00187 commit)
238-eeh-stop-if-reset_failed.patch
If the firmware is unable to reset the PCI slot for some reason, then
don't attempt any further recovery steps after that point. Instead,
mark the device as permanently failed.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e06b942521eb2cdaf232726f45a820d5837acb12 commit)
237-eeh-bridge-token.patch
Minor: the rtas-bridge token should be set up the same way that all
the other rtas tokens are set up.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 78379b6c5fc17b6666c40b05988e6708e98479c0 commit)
236-eeh-config-addr.patch
The PE configuration address wasn't being cnsistently used in all locations
where a config address is called for. This patch adds it to the places it
should have appeared in.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from c2bc904a28095aca0b04a37854b63b78622a032e commit)
235-eeh-set-pcidev-bugfix.patch
The pci device field of the pci_dn struct should be initialized to a
valid value.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from beb45c93d494a11c36e5b24f638e610db8428b54 commit)
234-eeh-find-pe.patch
The find_device_pe() routine is duplicated in two files. Remove one of
the two copies, declare the other extern.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 48408e708282d4d0269136ff27ea5acbd9410b5a commit)
26-eeh-partition-endpoint.patch
New versions of firmware introduce a new method by which the
"partitionable endpoint" (the point at which the pci bus is cut)
should be located. This code adds the support for this (mandatory)
new feature.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 9fcfb5d35b5294659f9299aa9cae6fd16325c07e commit)
25-pci-address-cache.patch
The core EEH file is rather large. This patch splits out a self-contained
chunk of it into its own file. This is the chunk that performes the
caching and lookup of pci devices based on the i/o addresses of thier
resoures. This code is almos architecture-independent and could be
used by any system that wanted to find a pci device based only on
the i/o address used by the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from b0b291d59906d4a9a89ed9e34d9fd684c7188924 commit)
Various PCI bus errors can be signaled by newer PCI controllers. The
core error recovery routines are architecture dependent. This patch adds
a recovery infrastructure for the PPC64 pSeries systems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e8ca11b460c4c9c7fa6b529be221529ebd770e38 commit)
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
more mutex debugging: check for held locks during memory freeing,
task exit, enable sysrq printouts, etc.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Don't clobber register %l0 while checking TI_SYS_NOERROR value in
syscall return path. This bug was introduced by:
db7d9a4eb7
Problem narrowed down by Luis F. Ortiz and Richard Mortimer.
I tried using %l2 as suggested by Luis and that works for me.
Looking at the code I wonder if it makes sense to simplify the code
a little bit. The following works for me but I'm not sure how to
exercise the "NOERROR" codepath.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of comparisons by one through the use of jb/je.
This patch also corrects the comments regarding the different key
lengths.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As the Crypto API now allows multiple implementations to be registered
for the same algorithm, we no longer have to play tricks with Kconfig
to select the right AES implementation.
This patch sets the driver name and priority for all the AES
implementations and removes the Kconfig conditions on the C implementation
for AES.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A lot of crypto code needs to read/write a 32-bit/64-bit words in a
specific gender. Many of them open code them by reading/writing one
byte at a time. This patch converts all the applicable usages over
to use the standard byte order macros.
This is based on a previous patch by Denis Vlasenko.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Patch from Ben Dooks
Properly tabulate the clock table in arch/arm/mach-s3c2410/clock.c
and put the requisite commas on the end of the structs.
Fix the comment about clock enable and disable in the setup code
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I upgraded my Toshiba Satellite BIOS recently to see if it would fix an
ACPI related problem I have
(http://bugzilla.kernel.org/show_bug.cgi?id=5727). Unfortunately, it
didn't, and moreover, Toshiba chose to change the system version in the
DMI table with the update, causing the OHCI1394 related quirk to break.
This patch updates the DMI table for the quirk to include Toshiba's new
version name for this machine; I've tested it and it seems to work fine.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updated printk and DBG with appropriate KERN_*.
Signed-off-by: Daniel Marjamäki <daniel.marjamaki@comhem.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the dependency from vmlinux to install, thus avoiding the
current situation where "make install" has a nasty tendency to leave
root-turds in the working directory.
It also updates x86-64 to be in sync with i386.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Patch from Deepak Saxena
In working on adding 36-bit addressed supersection support to ioremap(),
I came to the conclusion that it would be far simpler to do so by just
splitting __ioremap() into a main external interface and adding an
__ioremap_pfn() function that takes a pfn + offset into the page that
__ioremap() can call. This way existing callers of __ioremap() won't have
to change their code and 36-bit systems will just call __ioremap_pfn()
and we will not have to deal with unsigned long long variables.
Note that __ioremap_pfn() should _NOT_ be called directly by drivers
but is reserved for use by arch_ioremap() implementations that map
32-bit resource regions into the real 36-bit address and then call
this new function.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from SAN People
Following changes were made to clock.c:
1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.
Otherwise it's the same as the previous patch.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't set CONFIG_PPC_MULTIPLATFORM on iSeries (yet). Avoid
compiling in the prom_init stuff on iSeries.
Signed-off-by: Paul Mackerras <paulus@samba.org>
In add_memory() we should be using __va() to get a virtual address.
Spotted by Mike Kravetz.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The CONFIG_PPC_OF symbol is used to mean that the firmware device tree
access functions are available. Since we always have a device tree
with ARCH=powerpc, make CONFIG_PPC_OF always Y for ARCH=powerpc.
This fixes some compile errors reported by Kumar Gala, but in a
different way to his patch. This also makes prom_parse.o be compiled
only if CONFIG_PPC_OF so that non-OF ARCH=ppc platforms will compile.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When taking a DABR exception we were reporting the PC. It makes more
sense to report the address that caused the exception, and the gdb guys
would like it that way.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
POWER5+ adds new PMU groups and as such needs to be treated differently
by oprofile userspace. Change it to report itself as power5+.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My recent changes to oprofile broke it when built as a module. Fix it by
using an enum instead of a function pointer. This way we still retain
the oprofile configuration in the cputable.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds cpufreq support for all desktop "tower" G5 models. The
only G5 models still lacking cpufreq support at this point are the
Xserve and possibly the new iMac iSight (not tested). I'll have those
added soon. That patch uses the new platform functions interpreter to
implement frequency and voltage switching on most models.
Note that in order to find the low frequency value, I had to hack
something that might now work properly on all models, so if the
frequency value reported when running low speed looks bogus to you,
please report it to me. (Appart from a bogus reported value, things
should work fine).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the platform function interpreter itself along with the backends
for UniN/U3/U4, mac-io, GPIOs and i2c. It adds the ability to execute
those do-platform-* scripts in the device-tree (at least for most
devices for which a backend is provided). This should replace the clock
spreading hacks properly. It might also have an impact on all sort of
machines since some of the scripts marked "at init" will now be executed
on boot (or some other on sleep/wakeup), those will possibly do things
that the kernel didn't do at all, like setting some values into some i2c
devices (changing thermal sensor calibration or conversion rate) etc...
Thus regression testing is MUCH welcome. Also loook for errors in dmesg.
That's also why I've left rather verbose debugging enabled in this
version of the patch.
(I do expect some Windtunnel G4s to show some errors as they have an i2c
clock chip on the PMU bus that uses some primitives that the i2c backend
doesn't implement yet. I really need users that have one of those
machine to come back to me so we can get that done right, though the
errors themselves should be harmless, I suspect the machine might not
run at full speed).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the continuation of the previous patch. This one removes the old
PowerMac i2c drivers (i2c-keywest and i2c-pmac-smu) and replaces them
both with a single stub driver that uses the new PowerMac low i2c layer.
Now that i2c-keywest is gone, the low-i2c code is extended to support
interrupt driver transfers. All i2c busses now appear as platform
devices. Compatibility with existing drivers should be maintained as the
i2c bus names have been kept identical, except for the SMU bus but in
that later case, all users has been fixed.
With that patch added, matching a device node to an i2c_adapter becomes
trivial.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the first part of a rework of the PowerMac i2c code. It
completely reworks the "low_i2c" layer. It is now more flexible,
supports KeyWest, SMU and PMU i2c busses, and provides functions to
match device nodes to i2c busses and adapters.
This patch also extends & fix some bugs in the SMU driver related to i2c
support and removes the clock spreading hacks from the pmac feature code
rather than adapting them to the new API since they'll be replaced by
the platform function code completely in patch 3/5
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc64 has its own version of sys_time. It looks pretty scary, touching
a whole bunch of variables without any locking or memory ordering.
In fact, a recent bugreport has shown it can actually go backwards. Time
to remove it and just use the generic sys_time, which is implemented on
top of do_gettimeofday.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In 2.6.14, we had the following definition of _GLOBAL() in
include/asm-ppc/processor.h:
#define _GLOBAL(n)\
.stabs __stringify(n:F-1),N_FUN,0,0,n;\
.globl n;\
n:
In 2.6.15, as part of the great powerpc merge, we moved this definition to
include/asm-powerpc/ppc_asm.h, where it appears (to 32-bit code) as:
#define _GLOBAL(n) \
.text; \
.stabs __stringify(n:F-1),N_FUN,0,0,n;\
.globl n; \
n:
Mostly, this is fine. However, we also have the following, in
arch/ppc/boot/common/util.S:
.section ".relocate_code","xa"
[...]
_GLOBAL(flush_instruction_cache)
[...]
_GLOBAL(flush_data_cache)
[...]
The addition of the .text section definition in the definition of
_GLOBAL overrides the .relocate_code section definition. As a result,
these two functions don't end up in .relocate_code, so they don't get
relocated correctly, and the boot fails.
There's another suspicious-looking usage at kernel/swsusp.S:37 that
someone should look into. I did not exhaustively search the source
tree, though.
The following is the minimal patch that fixes the immediate problem.
I could easily be convinced that the _GLOBAL definition should be
modified to remove the ".text;" line either instead of, or in addition
to, this fix.
Signed-off-by: Paul Janzen <pcj@linux.sez.to>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For far, all SPU triggered interrupts always end up on
the first SMT thread, which is a bad solution.
This patch implements setting the affinity to the
CPU that was running last when entering execution on
an SPU. This should result in a significant reduction
in IPI calls and better cache locality for SPE thread
specific data.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One local variable is missing an __iomem modifier,
in another place, we pass a completely unused argument
with a missing __user modifier.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In a hypervisor based setup, direct access to the first
priviledged register space can typically not be allowed
to the kernel and has to be implemented through hypervisor
calls.
As suggested by Masato Noguchi, let's abstract the register
access trough a number of function calls. Since there is
currently no public specification of actual hypervisor
calls to implement this, I only provide a place that
makes it easier to hook into.
Cc: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Cc: Geoff Levand <geoff.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The logic for sys_spu_run keeps growing and it does
not really belong into file.c any more since we
moved away from using regular file operations to our
own syscall.
No functional change in here.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
checking bits manually might not be synchonized with
the use of set_bit/clear_bit. Make sure we always use
the correct bitops by removing the unnecessary
identifiers.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If creating one entry failed in spufs_fill_dir,
we never cleaned up the freshly created entries.
Fix this by calling the cleanup function on error.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If get_unused_fd failed in sys_spu_create, we never cleaned
up the created directory. Fix that by restructuring the
error path.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When spu_activate fails in spu_acquire_runnable, the
state must still be SPU_STATE_SAVED, we were
incorrectly setting it to SPU_STATE_RUNNABLE.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During an earlier cleanup, we lost the serialization
of multiple spu_run calls performed on the same
spu_context. In order to get this back, introduce a
mutex in the spu_context that is held inside of spu_run.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only checking for SPUFS_MAGIC is not reliable, because
it might not be unique in theory. Worse than that,
we accidentally allow spu_run to be performed on
any file in spufs, not just those returned from
spu_create as intended.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spu_forget will do mmput on the DMA address space,
which can lead to lots of other stuff getting triggered.
We better not hold a semaphore here that we might
need in the process.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to check for validity of owner under down_write,
down_read is not enough.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch enables support for pause(0) power management state
for the Cell Broadband Processor, which is import for power efficient
operation. The pervasive infrastructure will in the future enable
us to introduce more functionality specific to the Cell's
pervasive unit.
From: Maximino Aguilar <maguilar@us.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only build in support for ISA and PCI cases if we have enabled CONFIG_ISA
and CONFIG_PCI. Additionally, isa_bridge is a global so we shouldn't use
it a parameter name since it gets redefined to NULL when !CONFIG_PCI.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, we are not looking at all interrupt controller nodes in the
device tree even though the proper node was not found. This is causing
the system panic. The attached patch will scan all nodes until it finds
the proper interrupt controller type.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In setup_arch and setup_system call find_legacy_serial_ports() if we
build in support for 8250 serial ports instead of basing it on PPC_MULTIPLATFORM.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added a common udbg_progress for use by ppc_md.progress()
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the ability to configure and initialize legacy 8250 serials
ports on an SOC bus. Also, fixed an issue that we would not
configure any serial ports if "linux,stdout-path" was not found.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The checking of the baudrate in udbg_probe_uart_speed was
too tight and would cause reporting back of the default
baud rate in cases where the computed speed was valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The system will oops if an attempt is made to add memory to an
empty node/zone. This patch prevents adding memory to an empty
node. The code to dynamically add a node/zone is non-trivial.
This patch is temporary and will be removed when the ability
to dynamically add a node/zone is complete.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Building the arch/powerpc tree currently gives me
two warnings with gcc-4.0:
arch/powerpc/mm/imalloc.c: In function '__im_get_area':
arch/powerpc/mm/imalloc.c:225: warning: 'tmp' may be used uninitialized in this function
arch/powerpc/mm/hugetlbpage.c: In function 'hugetlb_get_unmapped_area':
arch/powerpc/mm/hugetlbpage.c:608: warning: unused variable 'vma'
both fixes are trivial.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds an option to remove vm86 support under CONFIG_EMBEDDED. Saves
about 5k.
This version eliminates most of the #ifdefs of the previous version and
instead uses function stubs in vm86.h. Also, release_vm86_irqs is moved
from asm-i386/irq.h to a more appropriate home in vm86.h so that the stubs
can live together.
$ size vmlinux-baseline vmlinux-novm86
text data bss dec hex filename
2920821 523232 190652 3634705 377611 vmlinux-baseline
2916268 523100 190492 3629860 376324 vmlinux-novm86
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Configurable 16-bit UID and friends support
This allows turning off the legacy 16 bit UID interfaces on embedded platforms.
text data bss dec hex filename
3330172 529036 190556 4049764 3dcb64 vmlinux-baseline
3328268 529040 190556 4047864 3dc3f8 vmlinux
From: Adrian Bunk <bunk@stusta.de>
UID16 was accidentially disabled for !EMBEDDED.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds configurable support for doublefault reporting on x86
add/remove: 0/3 grow/shrink: 0/1 up/down: 0/-13048 (-13048)
function old new delta
cpu_init 846 786 -60
doublefault_fn 188 - -188
doublefault_stack 4096 - -4096
doublefault_tss 8704 - -8704
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
APM doesn't _need_ the PM_LEGACY junk, so remove it's dependancy from
Kconfig, and ifdef the junk in the code. Whilst the ifdefs are ugly, when
the legacy stuff gets ripped out so will the ifdefs.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes it possible for boot code to use screen_info without dragging in
all of tty.h.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a hook so architectures can validate /dev/mem mmap requests.
This is analogous to validation we already perform in the read/write
paths.
The identity mapping scheme used on ia64 requires that each 16MB or
64MB granule be accessed with exactly one attribute (write-back or
uncacheable). This avoids "attribute aliasing", which can cause a
machine check.
Sample problem scenario:
- Machine supports VGA, so it has uncacheable (UC) MMIO at 640K-768K
- efi_memmap_init() discards any write-back (WB) memory in the first granule
- Application (e.g., "hwinfo") mmaps /dev/mem, offset 0
- hwinfo receives UC mapping (the default, since memmap says "no WB here")
- Machine check abort (on chipsets that don't support UC access to WB
memory, e.g., sx1000)
In the scenario above, the only choices are
- Use WB for hwinfo mmap. Can't do this because it causes attribute
aliasing with the UC mapping for the VGA MMIO space.
- Use UC for hwinfo mmap. Can't do this because the chipset may not
support UC for that region.
- Disallow the hwinfo mmap with -EINVAL. That's what this patch does.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove various things which were checking for gcc-1.x and gcc-2.x compilers.
From: Adrian Bunk <bunk@stusta.de>
Some documentation updates and removes some code paths for gcc < 3.2.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem. It is expected that /sbin/halt -p works exactly like
/sbin/halt, when the kernel does not implement power off functionality.
The kernel can do a lot of work in the reboot notifiers and in
device_shutdown before we even get to machine_power_off. Some of that
shutdown is not safe if you are leaving the power on, and it definitely
gets in the way of using sysrq or pressing ctrl-alt-del. Since the
shutdown happens in generic code there is no way to fix this in
architecture specific code :(
Some machines are kernel oopsing today because of this.
The simple solution is to turn LINUX_REBOOT_CMD_POWER_OFF into
LINUX_REBOOT_CMD_HALT if power_off functionality is not implemented.
This has the unfortunate side effect of disabling the power off
functionality on architectures that leave pm_power_off to null and still
implement something in machine_power_off. And it will break the build on
some architectures that don't have a pm_power_off variable at all.
On both counts I say tough.
For architectures like alpha that don't implement the pm_power_off variable
pm_power_off is declared in linux/pm.h and it is a generic part of our
power management code, and all architectures should implement it.
For architectures like parisc that have a default power off method in
machine_power_off if pm_power_off is not implemented or fails. It is easy
enough to set the pm_power_off variable. And nothing bad happens there,
the machines just stop powering off.
The current semantics are impossible without a flag at the top level so we
can avoid the problem code if a power off is not implemented. pm_power_off
is as good a flag as any with the bonus that it works without modification
on at least x86, x86_64, powerpc, and ppc today.
Andrew can you pick this up and put this in the mm tree. Kernels that
don't compile or don't power off seem saner than kernels that oops or
panic. Until we get the arch specific patches for the problem
architectures this probably isn't smart to push into the stable kernel.
Unfortunately I don't have the time at the moment to walk through every
architecture and make them work. And even if I did I couldn't test it :(
From: Hirokazu Takata <takata@linux-m32r.org>
Add pm_power_off() for build fix of arch/m32r/kernel/process.c.
From: Miklos Szeredi <miklos@szeredi.hu>
UML build fix
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ptrace_get_task_struct() helper that I added as part of the ptrace
consolidation is useful in variety of places that currently opencode it.
Switch them to the common helpers.
Add a ptrace_traceme() helper that needs to be explicitly called, and simplify
the ptrace_get_task_struct() interface. We don't need the request argument
now, and we return the task_struct directly, using ERR_PTR() for error
returns. It's a bit more code in the callers, but we have two sane routines
that do one thing well now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the rtc_interrupt() prototype to rtc.h and removes the
prototypes from C files.
It also renames static rtc_interrupt() functions in
arch/arm/mach-integrator/time.c and arch/sh64/kernel/time.c to avoid compile
problems.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Gortmaker <p_gortmaker@yahoo.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If MODE_TT=n, MODE_SKAS must be y.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes some mangled whitespace added by the earlier trap_user.c patch.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The serial UML OS-abstraction layer patch (um/kernel dir).
This joins trap_user.c and trap_kernel.c files.
Signed-off-by: Gennady Sharapov <Gennady.V.Sharapov@intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The serial UML OS-abstraction layer patch (um/kernel dir).
This moves all systemcalls from trap_user.c file under os-Linux dir
Signed-off-by: Gennady Sharapov <Gennady.V.Sharapov@intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The serial UML OS-abstraction layer patch (um/kernel dir).
This moves all systemcalls from signal_user.c file under os-Linux dir
Signed-off-by: Gennady Sharapov <Gennady.V.Sharapov@intel.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ds1620 module is using gpio_read symbol, so works only if "built-in" symbol
needs to be exported from the kernel image
Signed-off-by: Woody Suwalski <woodys@xandros.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
____cacheline_maxaligned_in_smp is currently used to align critical structures
and avoid false sharing. It uses per-arch L1_CACHE_SHIFT_MAX and people find
L1_CACHE_SHIFT_MAX useless.
However, we have been using ____cacheline_maxaligned_in_smp to align
structures on the internode cacheline size. As per Andi's suggestion,
following patch kills ____cacheline_maxaligned_in_smp and introduces
INTERNODE_CACHE_SHIFT, which defaults to L1_CACHE_SHIFT for all arches.
Arches needing L3/Internode cacheline alignment can define
INTERNODE_CACHE_SHIFT in the arch asm/cache.h. Patch replaces
____cacheline_maxaligned_in_smp with ____cacheline_internodealigned_in_smp
With this patch, L1_CACHE_SHIFT_MAX can be killed
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a number of miscellanous items:
(1) Declare lock sections in the linker script.
(2) Recurse in the correct manner in the arch makefile.
(3) asm/bug.h requires asm/linkage.h to be included first. One C file puts
asm/bug.h first.
(4) Add an empty RTC header file to avoid missing header file errors.
(5) sg_dma_address() should use the dma_address member of a scatter list.
(6) Add trivial pci_unmap support.
(7) Add pgprot_noncached()
(8) Discard u_quad_t.
(9) Use ~0UL rather than ULONG_MAX in unistd.h in case the latter isn't
declared.
(10) Add an empty VGA header file to avoid missing header file errors.
(11) Add an XOR header file to use the generic XOR stuff.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Force the 8230 serial driver to be built in if the on-CPU UARTs are to be
used. It can't be used as a module because the arch setup needs to call into
it.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix PCMCIA configuration for FRV by including the stock PCMCIA configuration
description file.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the exception table handling so that modules exceptions are dealt with.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Export a number of features required to build all the modules. It also
implements the following simple features:
(*) csum_partial_copy_from_user() for MMU as well as no-MMU.
(*) __ucmpdi2().
so that they can be exported too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drop support for debugging features that aren't supported on FRV:
(*) EARLY_PRINTK
The on-chip UARTs are set up early enough that this isn't required,
and VGA support isn't available. There's also a gdbstub available.
(*) DEBUG_PAGEALLOC
This can't be easily be done since we use huge static mappings to
cover the kernel, not pages.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drop support for 8-bit and 16-bit xchg and cmpxchg emulation and implements
32-bit xchg with the SWAP/SWAPI instruction.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_migrate_pages implementation using swap based page migration
This is the original API proposed by Ray Bryant in his posts during the first
half of 2005 on linux-mm@kvack.org and linux-kernel@vger.kernel.org.
The intent of sys_migrate is to migrate memory of a process. A process may
have migrated to another node. Memory was allocated optimally for the prior
context. sys_migrate_pages allows to shift the memory to the new node.
sys_migrate_pages is also useful if the processes available memory nodes have
changed through cpuset operations to manually move the processes memory. Paul
Jackson is working on an automated mechanism that will allow an automatic
migration if the cpuset of a process is changed. However, a user may decide
to manually control the migration.
This implementation is put into the policy layer since it uses concepts and
functions that are also needed for mbind and friends. The patch also provides
a do_migrate_pages function that may be useful for cpusets to automatically
move memory. sys_migrate_pages does not modify policies in contrast to Ray's
implementation.
The current code here is based on the swap based page migration capability and
thus is not able to preserve the physical layout relative to it containing
nodeset (which may be a cpuset). When direct page migration becomes available
then the implementation needs to be changed to do a isomorphic move of pages
between different nodesets. The current implementation simply evicts all
pages in source nodeset that are not in the target nodeset.
Patch supports ia64, i386 and x86_64.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oops, forgot to compile the VMALLOCBASE/VMALLOC_START patch on
iSeries. VMALLOC_START is defined in pgtable.h whereas previously
VMALLOCBASE was previously defined in page.h. lparmap.c needs to be
updated appropriately.
Booted on iSeries RS64 (now).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds oprofile support for the 7450 and all its multitudinous
derivatives.
* Added 7450 (and derivatives) support for oprofile
* Changed e500 cputable to have oprofile model and cpu_type fields
* Added support for classic 32-bit performance monitor interrupt
* Cleaned up common powerpc oprofile code to be as common as possible
* Cleaned up oprofile_impl.h to reflect 32 bit classic code
* Added 32-bit MMCRx bitfield definitions and SPR numbers
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pci_address_to_pio is missing a closing curly brace
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes pci_address_to_pio() to return an unsigned long (to be safe)
and fixes a bug in the implementation that caused it to return a bogus
IO port number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64, we independently define VMALLOCBASE and VMALLOC_START to be
the same thing: the start of the vmalloc() area at 0xd000000000000000.
VMALLOC_START is used much more widely, including in generic code, so
this patch gets rid of the extraneous VMALLOCBASE.
This does require moving the definitions of region IDs from page_64.h
to pgtable.h, but they don't clearly belong in the former rather than
the latter, anyway. While we're moving them, clean up the definitions
of the REGION_IDs:
- Abolish REGION_SIZE, it was only used once, to define
REGION_MASK anyway
- Define the specific region ids in terms of the REGION_ID()
macro.
- Define KERNEL_REGION_ID in terms of PAGE_OFFSET rather than
KERNELBASE. It amounts to the same thing, but conceptually this is
about the region of the linear mapping (which starts at PAGE_OFFSET)
rather than of the kernel text itself (which is at KERNELBASE).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch enabling the new G5's with U4 broke initialization of the DART
driver, causing it to trigger a BUG_ON for a case that is actually
valid. This patch fixes it:
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental ! There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added the ability to determine if an outbound window in the PCI host
controller is for prefetchable memory and report it as such.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is code in the RPAPHP directory that is identical to this routine;
I'll be removing that code in an upcoming patch, but this patch is needed
to expose the function to make it callable.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup the MPIC IO-APIC workarounds, make them a bit more generic,
smaller and faster.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a defconfig for PowerMac with ARCH=powerpc
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove a comment in head.S which is no longer relevant.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We used to print a NUMA cpu summary at boot before the hotplug cpu code
was added. This has been useful for catching machine configuration as
well as firmware bugs in the past.
This patch restores that functionality. An example of the output is:
Node 0 CPUs: 0-7
Node 1 CPUs: 8-15
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
/dev/nvram uses the user-provided read/write size
for kmalloc, which fails, if a large number is passed.
This will always use a single page at most, which
can be expected to succeed.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently crash in the fedora installer because the keyboard
driver tries to access I/O space that is not there on our hardware.
This uses the same solution as powermac by just marking all
legacy i/o as invalid.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
So far, the iommu code was hardwired to a linear mapping
between 0x20000000 and 0x40000000, so it could only support
512MB of RAM.
This patch still keeps the linear mapping, but looks for
proper ibm,dma-window properties to set up larger windows,
this makes the maximum supported RAM size 2GB.
If there is anything unusual about the dma-window properties,
we fall back to the old behavior.
We also support switching off the iommu completely now
with the regular iommu=off command line option.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Output from hexdump with "%08x" depends on HOST platform's endian.
When building linux by cross toolchain, that difference makes errors.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoff.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One of my last patches contained a broken line
from splitting out some other changes, this
restores a working version.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One of the two users of spufs_calls.owner still has a race
when calling try_module_get while the module is removed.
This makes it use the correct instance of owner.
Noticed by Milton Miller.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for the TQ Components TQM85xx modules. Currently the
modules TQM8540/8541/8555/8560 are supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I can't really get a conclusive answer from the firmware
people what to check for, so I just try scanning for
anything that starts with "IBM,CPB", which should be
correct for all hardware produced so far and for
systemsim.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Handling mailbox interrupts was broken in multiple respects,
the combination of which was hiding the bugs most of the time.
- The ibox interrupt mask was open initially even though there
are no waiters on a newly created SPU.
- Acknowledging the mailbox interrupt did not work because
it is level triggered and the mailbox data is never retrieved
from inside the interrupt handler.
- The interrupt handler delivered interrupts with a disabled
mask if another interrupt is triggered for the same class
but a different mask.
- The poll function did not enable the interrupt if it had not
been enabled, so we might run into the poll timeout if none of
the other bugs saved us and no signal was delivered.
We probably still have a similar problem with blocking
read/write on mailbox files, but that will result in extra
wakeup in the worst case, not in incorrect behaviour.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reduces lock complexity of SPU scheduler, particularly
for involuntary preemptive switches. As a result the new code
does a better job of mapping the highest priority tasks to SPUs.
Lock complexity is reduced by using the system default workqueue
to perform involuntary saves. In this way we avoid nasty lock
ordering problems that the previous code had. A "minimum timeslice"
for SPU contexts is also introduced. The intent here is to avoid
thrashing.
While the new scheduler does a better job at prioritization it
still does nothing for fairness.
From: Mark Nutter <mnutter@us.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes it easier to preempt an SPU context by
having the scheduler hold ctx->state_sema for much shorter
periods of time.
As part of this restructuring, the control logic for the "run"
operation is moved from arch/ppc64/kernel/spu_base.c to
fs/spufs/file.c. Of course the base retains "bottom half"
handlers for class{0,1} irqs. The new run loop will re-acquire
an SPU if preempted.
From: Mark Nutter <mnutter@us.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spufs is rather noisy when debugging is enabled, this
turns off the messages for production use.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
try_module_get returns true when NULL arguments, so
we first need to check if there is a module loaded before
getting the reference count.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With the new rules for reserved pages, the spufs now
needs working page reference counting.
I should probably look into converting to vm_insert_page,
but for now this patch makes spufs work again.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes all exported symbols of spufs to EXPORT_SYMBOL_GPL.
The spu_ibox_read/spu_wbox_write symbols are not exported
any more when the scheduler patch is applied.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Milton has proposed that we should support a "linux,usable-memory" property
on memory nodes which describes, in preference to "reg", the regions of memory
Linux should use.
This facility is required for kdump to inform the second kernel which memory
it should use.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds code to parse and setup the crash kernel resource in the
first kernel. PPC64 ignores the @x part, we always run at 32 MB.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implementing the machine_crash_shutdown which will be called by
crash_kexec (called in case of a panic, sysrq etc.). Disable the
interrupts, shootdown cpus using debugger IPI and collect regs
for all CPUs.
elfcorehdr= specifies the location of elf core header stored by
the crashed kernel. This command line option will be passed by
the kexec-tools to capture kernel.
savemaxmem= specifies the actual memory size that the first kernel
has and this value will be used for dumping in the capture kernel.
This command line option will be passed by the kexec-tools to
capture kernel.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a few places where we need to fix things up for the kernel to work
if it's linked at 32MB:
- platforms/powermac/smp.c
To start secondary cpus on pmac we patch the reset vector, which is fine.
Except if we're above 32MB we don't have enough bits for an absolute branch,
it needs to relative.
- kernel/head_64.s
- A few branches in the cpu hold code need to load the full target address
and do a bctr.
- after_prom_start needs to load PHYSICAL_START as the dest address, not 0.
- The exception prolog needs to load the low word of the target adddress,
not just the low halfword.
- Fixup handling of the initial stab address.
- kernel/setup_64.c
smp_release_cpus() needs to write 1 to the spinloop flag near 0, not 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Regardless of where the kernel's linked we always get interrupts at low
addresses. This patch creates a trampoline in the first 3 pages of memory,
where interrupts land, and patches those addresses to jump into the real
kernel code at PHYSICAL_START.
We also need to reserve the trampoline code and a bit more in prom.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The fwnmi vectors can be anywhere < 32 MB, so we need to use a trampoline
for them. The kdump kernel will register the trampoline addresses, which will
then jump up to the real code above 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a Kconfig variable, CONFIG_CRASH_DUMP, which configures the
built kernel for use as a Kdump kernel.
Currently "all" this involves is changing the value of KERNELBASE to 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows iSeries to build again. It just moves pci_address_to_pio
outside the #ifdef CONFIG_PPC_MULTIPLATFORM.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Minor: use macro to perform void pointer deref; this may someday help
avoid pointer typecasting errors.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This places dynamically added memory within the appropriate
numa node. A new routine hot_add_scn_to_nid() replicates most of
the memory scanning code in parse_numa_properties().
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch separates usage of KERNELBASE and PAGE_OFFSET. I haven't
looked at any of the PPC32 code, if we ever want to support Kdump on
PPC we'll have to do another audit, ditto for iSeries.
This patch makes PAGE_OFFSET the constant, it'll always be 0xC * 1
gazillion for 64-bit.
To get a physical address from a virtual one you subtract PAGE_OFFSET,
_not_ KERNELBASE.
KERNELBASE is the virtual address of the start of the kernel, it's
often the same as PAGE_OFFSET, but _might not be_.
If you want to know something's offset from the start of the kernel
you should subtract KERNELBASE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a bunch of code that compares an address with KERNELBASE to see if
it's a "kernel address", ie. >= KERNELBASE. The proper test is actually to
compare with PAGE_OFFSET, since we're going to change KERNELBASE soon.
So replace all of them with an is_kernel_addr() macro that does that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently machine_crash_shutdown() gets a struct pt_regs, but doesn't pass it
through to the ppc_md function, it should.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we select ppc32 under the powerpc architecture we get the
error below. This relates to defining distribute_irqs when this
configuratiom option is undefined.
CC arch/powerpc/sysdev/mpic.o
.../arch/powerpc/sysdev/mpic.c: In function `mpic_setup_this_cpu':
.../arch/powerpc/sysdev/mpic.c:788: error: `CONFIG_IRQ_ALL_CPUS'
undeclared (first use in this function)
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up the currently available memory models for ppc32 under
the powerpc architecture. We need FLATMEM for ppc32: enable it.
SPARSEMEM is not parameterised for ppc32 so disable that. Take this
opportunity to clean up white space for FLATMEM_ENABLE.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is an updated version of the patch that panics if no memory is
found as Nathan suggested. I'm still concerned that panic strings
(not just the one added here) at this stage of booting do not show
up on my system. But, that is an issue separate from this patch.
Combine get_mem_*_cells() routines to avoid multiple memory node
lookups. Added missing of_node_put() call. Changed variable names
to help with some confusion as to meaning.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the OF address parsers to return the IO flags
indicating the type of address obtained. It also adds a PCI
call for converting physical addresses that hit IO space into
into IO tokens, and add routines that return the translated
addresses into struct resource
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The udbg low level io layer has an issue with udbg_getc() returning a
char (unsigned on ppc) instead of an int, thus the -1 if you had no
available input device could end up turned into 0xff, filling your
display with bogus characters. This fixes it, along with adding a little
blob to xmon to do a delay before exiting when getting an EOF and fixing
the detection of ADB keyboards in udbg_adb.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When compiling without BOOTX_TEXT the following warning is emitted.
Fix up the definition to only be made when required.
CC arch/powerpc/platforms/powermac/udbg_adb.o
.../arch/powerpc/platforms/powermac/udbg_adb.c:41: warning:
`udbg_adb_use_btext' defined but not used
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
udbg_adb_init() has become dependent on btext_drawchar, even when
BOOTX_TEXT support is not selected. This leads to the error below.
Make the check dependant on BOOTX_TEXT.
LD .tmp_vmlinux1
arch/powerpc/platforms/built-in.o(.toc1+0xa40): undefined
reference to `btext_drawchar'
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
23-rpaphp-migrate.patch (parts)
This patch moves some pci device add & remove code from the PCI
hotplug directory to the arch/powerpc/kernel directory, and cleans
it up a tad. The primary reason for this is that the code performs
some fairly generic operations that are shared with the PCI error
recovery code (living in the arch/powerpc/kernel directory).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
22-rpaphp-eliminate-dupe-code.patch (parts)
The RPAPHP code contains two routines that appear to be gratuitous
copies of very similar pci code. In particular,
rpaphp_claim_resource ~~ pci_claim_resource
rpadlpar_claim_one_bus == pcibios_claim_one_bus
This makes pcibios_claim_one_bus from arch/powerpc/kernel/pci_64.c
available to the RPAPHP code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
20-rpaphp-eeh-cleanup.patch
This patch move some code from the rpaphp directory, to the powerpc
directory, where it should have been all along (Among other things, I
need it in the powerpc directory for the PCI error recovery.)
Please note that patch affects TWO maintainers: Paul, after applying
the powerpc part, please ask that GregKH appli the PCI part. It is safe
to have the powerpc part go in first. It would be bad to have the
PCI part go in first.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I started to add missing of_node_put() calls to the routines that
determine the number of cells for memory. Decided to combine the
routines instead of making separate node lookups. Changed variable
names to help with some confusion as to meaning.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the new serial probe code with some PCI MMIO UARTs, and fixes
CHRP build with ARCH=powerpc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes ARCH=ppc build in your powerpc tree again, with the new
syscall entry/exit path.
Still doesn't actually boot on my Pegasos; the last thing I see is
'MMU:exit'. But at least it builds -- I'll look at why it doesn't boot
later, so that I can see if the mv643xx_eth actually works with ARCH=ppc
(it doesn't with ARCH=powerpc; two in every three packets I receive are
offset by 4 bytes).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates m8xx_wdt as follows:
1) Remove now obsolete fpos check in the write() function. The driver is
currently non functional due to this bug.
2) Use in/out macros for register access.
3) Allows m8xx_wdt to use a kernel timer instead of the builtin RTC/PIT
for keep-alive trigger (which is responsible for servicing the watchdog
until an userspace application takes over). For instance Cyclades PRxK
boards (MPC 855T based) have a non-functional internal RTC/PIT unit.
Behaviour for boards with RTC/PIT is unchaged.
4) The last change required moving the RTCSC register setting code
to a weak function which can be overriden by board specific files.
Otherwise the timer init code trashes the register making it impossible
for m8xx_wdt to detect the situation.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Thu, 2005-11-24 at 12:51 +0000, David Woodhouse wrote:
> Somehow this one slipped through the cracks; when we ended up in
> do_signal() on a 32-bit kernel but without having the caller-saved
> registers into the regs, we didn't set the TIF_SAVE_NVGPRS flag to
> ensure they got saved later.
Oh, and if we actually set the flag, then we fairly quickly find out
that I was a bit overzealous in copying code from entry_64.S ... :)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Somehow this one slipped through the cracks; when we ended up in
do_signal() on a 32-bit kernel but without having the caller-saved
registers into the regs, we didn't set the TIF_SAVE_NVGPRS flag to
ensure they got saved later.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, 2005-11-22 at 15:49 +1100, Benjamin Herrenschmidt wrote:
> This moves the discovery of legacy serial ports to a separate file,
> makes it common to ppc32 and ppc64, and reworks it to use the new OF
> address translators to get to the ports early. This new version can also
> detect some PCI serial cards using legacy chips and will probably match
> those discovered port with the default console choice.
This makes it deal with the fact that the Pegasos firmware reports that
its clock frequency is zero...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My previous patches inadvertently broke building a G5 kernel with
CONFIG_XMON enabled. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes several unnecessary fields from the paca:
- next_jiffy_update_tb was simply unused. Remove trivially.
- The exdsi exception save area was not used. There were plans to use
it, but they never seem to have gone anywhere. If they ever do, we
can put it back. Remove from the paca, and from asm-offsets.c
- The default_decr field was used from asm, but was only ever assigned
the value of tb_ticks_per_jiffy. Just access tb_ticks_per_jiffy from
asm directly instead.
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On iSeries, the paca contains, amongst other things an ItLpRegSave
structure used by the hypervisor to save registers. The hypervisor
locates this area through a pointer at the beginning of the paca, so
the structure itself can be located elsewhere. This patch moves the
reg_save area out into its own array. This reduces the amount of
iSeries specific gunk which is visible to general powerpc code via
paca.h
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the powerpc version of hugetlb_get_unmapped_area() entirely
ignores the hint address. The only way to get a hugepage mapping at a
specified address is with MAP_FIXED, in which case there's no way
(short of parsing /proc/self/maps) for userspace to tell if it will
clobber an existing mapping. This is inconvenient, so the patch below
makes hugepage mappings use the given hint address if possible.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Sam Ravnborg pointed out that calling if_changed was redundant in the
rule since a prerequisite had to have changed for us to get there.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Add support for building uImages
Add support to build a kernel image bootable by u-boot.
Most of the makefile foo is taken from arch/ppc/boot/images/Makefile
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Encode the sub bus number into the real irq number (even though it
is always zero for now) so that we have enough information to do
the EOI in iseries_end_IRQ.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
ARCH=powerpc couldn't boot from BootX as it uses a "different" way of
getting in the kernel. This patch adds the necessary trampolines,
creating a flattened device-tree from the tree passed from MacOS, and
initializing the btext engine early for really-early debugging.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.
For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.
Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.
It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Parsing addresses extracted from Open Firmware isn't a simple matter. We
have various bits of code that try to do it in various place, including
some heuristics in prom.c that pre-parse addresses at boot and fill
device-nodes "addrs", but those are dodgy at best and I want to
deprecate them. So this patch introduces a new set of routines that
should be capable of parsing most types of addresses and translating
them into CPU physical addresses. It currently works for things on PCI
busses and ISA busses and should work on "standard" busses like the root
bus or the MacIO bus that don't put funky flags in addresses. If you
have other bus types that do use funky flags, you'll have to add new bus
type translators, which is fairly easy.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, 2005-11-15 at 18:52 +0000, David Woodhouse wrote:
> This cleanup patch speeds up the null syscall path on ppc64 by about 3%,
> and brings the ppc32 and ppc64 code slightly closer together.
Needs this unless your binutils, like mine, are clever enough to notice
my stupidity and fix it up automatically...
Spotted by Paul.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a scheduler for SPUs to make it possible to use
more logical SPUs than physical ones are present in the
system.
Currently, there is no support for preempting a running
SPU thread, they have to leave the SPU by either triggering
an event on the SPU that causes it to return to the
owning thread or by sending a signal to it.
This patch also adds operations that enable accessing an SPU
in either runnable or saved state. We use an RW semaphore
to protect the state of the SPU from changing underneath
us, while we are holding it readable. In order to change
the state, it is acquired writeable and a context save
or restore is executed before downgrading the semaphore
to read-only.
From: Mark Nutter <mnutter@us.ibm.com>,
Uli Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the source code that is used to generate spu_save_dump.h and
spu_restore_dump.h. Since a full spu tool chain is needed to
generate these files, the default remains to use the shipped
versions in order to keep the number of tools for building the
kernel down.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the code needed to perform a context switch from
spufs, following the recommended 76-step sequence.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add some infrastructure for saving and restoring the context of an
SPE. This patch creates a new structure that can hold the whole
state of a physical SPE in memory. It also contains code that
avoids races during the context switch and the binary code that
is loaded to the SPU in order to access its registers.
The actual PPE- and SPE-side context switch code are two separate
patches.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the current version of the spu file system, used
for driving SPEs on the Cell Broadband Engine.
This release is almost identical to the version for the
2.6.14 kernel posted earlier, which is available as part
of the Cell BE Linux distribution from
http://www.bsc.es/projects/deepcomputing/linuxoncell/.
The first patch provides all the interfaces for running
spu application, but does not have any support for
debugging SPU tasks or for scheduling. Both these
functionalities are added in the subsequent patches.
See Documentation/filesystems/spufs.txt on how to use
spufs.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the necessary core bus support used by device drivers
that sit on the IBM GX bus on modern pSeries machines like the Galaxy
infiniband for example. It provide transparent DMA ops (the low level
driver works with virtual addresses directly) along with a simple bus
layer using the Open Firmware matching routines.
Signed-off-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleanup patch speeds up the null syscall path on ppc64 by about 3%,
and brings the ppc32 and ppc64 code slightly closer together.
The ppc64 code was checking current_thread_info()->flags twice in the
syscall exit path; once for TIF_SYSCALL_T_OR_A before disabling
interrupts, and then again for TIF_SIGPENDING|TIF_NEED_RESCHED etc after
disabling interrupts. Now we do the same as ppc32 -- check the flags
only once in the fast path, and re-enable interrupts if necessary in the
ptrace case.
The patch abolishes the 'syscall_noerror' member of struct thread_info
and replaces it with a TIF_NOERROR bit in the flags, which is handled in
the slow path. This shortens the syscall entry code, which no longer
needs to clear syscall_noerror.
The patch adds a TIF_SAVE_NVGPRS flag which causes the syscall exit slow
path to save the non-volatile GPRs into a signal frame. This removes the
need for the assembly wrappers around sys_sigsuspend(),
sys_rt_sigsuspend(), et al which existed solely to save those registers
in advance. It also means I don't have to add new wrappers for ppoll()
and pselect(), which is what I was supposed to be doing when I got
distracted into this...
Finally, it unifies the ppc64 and ppc32 methods of handling syscall exit
directly into a signal handler (as required by sigsuspend et al) by
introducing a TIF_RESTOREALL flag which causes _all_ the registers to be
reloaded from the pt_regs by taking the ret_from_exception path, instead
of the normal syscall exit path which stomps on the callee-saved GPRs.
It appears to pass an LTP test run on ppc64, and passes basic testing on
ppc32 too. Brief tests of ptrace functionality with strace and gdb also
appear OK. I wouldn't send it to Linus for 2.6.15 just yet though :)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved 83xx and QUICC Engine interrupt handling code into arch/powerpc
as a precursor of getting 83xx sub-arch building in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges, to some extent, the PPC32 and PPC64 kexec implementations.
We adopt the PPC32 approach of having ppc_md callbacks for the kexec functions.
The current PPC64 implementation becomes the "default" implementation for PPC64
which platforms can select if they need no special treatment.
I've added these default callbacks to pseries/maple/cell/powermac, this means
iSeries no longer supports kexec - but it never worked anyway.
I've renamed PPC32's machine_kexec_simple to default_machine_kexec, inline with
PPC64. Judging by the comments it might be better named machine_kexec_non_of,
or something, but at the moment it's the only implementation for PPC32 so it's
the "default".
Kexec requires machine_shutdown(), which is in machine_kexec.c on PPC32, but we
already have in setup-common.c on powerpc. All this does is call
ppc_md.nvram_sync, which only powermac implements, so instead make
machine_shutdown a ppc_md member and have it call core99_nvram_sync directly
on powermac.
I've also stuck relocate_kernel.S into misc_32.S for powerpc.
Built for ARCH=ppc, and 32 & 64 bit ARCH=powerpc, with KEXEC=y/n. Booted on
P5 LPAR and successfully kexec'ed.
Should apply on top of 493f25ef40.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the EXPORT_SYMBOL'ed but completely unused variable
ucSystemType and removes the unneeded EXPORT_SYMBOL(_prep_type).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
EPXA10DB seems to be uncared for:
- the "PLD" code has never been merged
- no one has reported that this platform has been broken since
at least 2.6.10
- interest seems to have dried up around March 2003.
Therefore, remove EPXA10DB support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This was causing some ordering problems. Remove the up-front evaluation
and just revaluate the compiler version each time we need it.
(The up-front evaluation was problematic because some architectures modify
the value of $(CC)).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Fix a gcc4 build error (incomplete element type) in the pxa SharpSL
PM code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Many arches make shared objects for VDSOs. Generally exclude them.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This was harmless, but for the case of a device that had no irq
pre-defined we would incorrectly suggest that "usepirqmask" might make a
difference. It never would, and the message was just confusing people.
Reported in the dmesg of Etienne Lorrain.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New feature V=V qdio pass-through.
QDIO and HiperSockets processing in z/VM V=V guest environments (as well as
V=R with z/VM running in LPAR mode) requires shadowing of all QDIO
architecture queue elements. Especially the shadowing of SBALs and SLSBs
structures in the hypervisor, and the need to issue SIGA SYNC operations to
observe state changes, eventually causes significant CPU processing overhead
in the hypervisor.
The QDIO pass-through support for V=V guests avoids the shadowing of SBALs and
SLSBs. This significantly reduces the hypervisor overhead for QDIO based I/O.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the hardware accelerated AES crypto algorithm.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the hardware accelerated sha256 crypto algorithm.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all references to z990 by s390 in the in-kernel crypto files in
arch/s390/crypto. The code is not specific to a particular machine (z990) but
to the s390 platform. Big diff, does nothing..
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are some more places where the use of cputime_t instead of an integer
type and the associated macros is necessary for the virtual cputime accounting
on s390. Affected are the s390 specific appldata code and BSD process
accounting.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check return code of do_sigaltstack and force a SIGSEGV if it is -EFAULT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert __access_ok to an inline C function and change __get_user primitive to
avoid uaccess compiler warnings.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh Dickins <hugh@veritas.com>
Fix the broken atomic_cmpxchg primitive. Add atomic_sub_and_test,
atomic64_sub_return, atomic64_sub_and_test, atomic64_cmpxchg,
atomic64_add_unless and atomic64_inc_not_zero. Replace old style
atomic_compare_and_swap by atomic_cmpxchg. Shorten the whole header by
defining most primitives with the two inline functions atomic_add_return and
atomic_sub_return.
In addition this patch contains the s390 related fixes of Hugh's "mm: fill
arch atomic64 gaps" patch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Free the network IRQ when closing down the network devices at shutdown.
Delete the device from the opened devices list on close.
These prevent an -EBADF when later disabling SIGIO on all extant descriptors
and a complaint from free_irq about freeing the IRQ twice.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up some bogus spacing in the mconsole driver. Also delete the
emacs formatting comment at the end.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass sysrq output back to the mconsole client using the mechanism
introduced for stack output.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The stack command now sends the printk output back to the mconsole client.
This is done by registering a special console for the mconsole driver. This
receives all printk output. Normally, it is ignored, but when a stack command
is issued, any printk output will be sent back to the client.
This will capture any printk output, whether it is stack output or not, since
we can't tell the difference.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed for the console output patch, since we have a possibly
non-NULL-terminated string there. So, the new interface takes a string and a
length, and the old interface calls strlen on its string and calls the new
interface with the length.
There's also a bit of whitespace cleanup.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Produce a compile-time error if both MODE_SKAS and MODE_TT are disabled.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Code cleanup - unregister_winch and winch_cleanup had some duplicate code.
This is now abstracted out into free_winch.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch cleans up the umid code:
- The only_if_set argument to get_umid is gone.
- get_umid returns an empty string rather than NULL if there is no umid.
- umid_is_random is gone since its users went away.
- Some printfs were turned into printks because the code runs late enough
that printk is working.
- Error paths were cleaned up.
- Some functions now return an error and let the caller print the error
message rather than printing it themselves. This eliminates the practice of
passing a pointer to printf or printk in, depending on where in the boot
process we are.
- Major tidying of not_dead_yet - mostly error path cleanup, plus a comment
explaining why it doesn't react to errors the way you might expect.
- Calls to os_* interfaces that were moved under os are changed back to
their native libc forms.
- snprintf, strlcpy, and their bounds-checking friends are used more often,
replacing by-hand bounds checking in some places.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I reworked Gennady's umid OS abstraction patch because the code shouldn't
be moved entirely to os. As it turns out, I moved most of it anyway. This
patch is the minimal one needed to move the code and have it work.
It turns out that the concept of the umid is OS-independent, but
almost everything else about the implementation is OS-dependent.
This is code movement without cleanup - a follow-on patch tidies
everything up without shuffling code around.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for throttling and unthrottling input when the tty
driver can't handle it.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the tty flip_buf is full, it's a good idea to delay the input processing
for a jiffy, rather than just scheduling the tasklet immediately.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch simplifies the opening and closing of host console devices and the
registration and deregistration of IRQs. The intent is to make it obvious
that an IRQ can't exist without an open file descriptor.
chan_enable will now open the channel, and when both opening and IRQ
registration are desired, this should be used. Opening only is done for the
initial console, so that interface still needs to exist.
The free_irqs_later interface is now gone. It was intended to avoid freeing
an IRQ while it was being processed. It did this, but it didn't eliminate the
possiblity of free_irq being called from an interrupt, which is bad. In its
place is a list of irqs to be freed, which is processed by the signal handler
just before exiting. close_one_chan now disables irqs.
When a host device disappears, it is just closed, and that disables IRQs.
The device id registered with the IRQ is now the chan structure, not the tty.
This is because the interrupt arrives on a descriptor associated with the
channel. This caused equivalent changes in the arguments to line_timer_cb.
line_disable is gone since it is not used any more.
The count field in the line structure is gone. tty->count is used instead.
The complicated logic in sigio_handler with freeing IRQs when necessary and
making sure its idea of the next irq is correct is now much simpler. The irq
list can't be rearranged underneath it, so it is now a simple list walk.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes when console devices are configured in order to prepare the
ground for the next patch.
parse_chan_pair is now done earlier, when initcalls are run, rather than when
the device is opened.
When a host device disappears, the channel list is closed, but not freed.
This is required by the previous change. line_config now takes the options
structure as an argument, and line_open doesn't.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
line_setup is changed to return the device which it set up, rather than just
success or failure. This will be important in the line-config patch.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some structure fields were being dynamically initialized when they could be
initialized at compile-time instead. This also makes some declarations static
(in the C sense).
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bit of restructuring which eliminates the all_allowed argument (which is
mconsole-specific) to line_setup. That logic is moved to the mconsole
callback.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes a structure field which turned out to be pointless, and
references to it.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch replaces instances of "sizeof(foo)/sizeof(foo[0])" with
ARRAY_SIZE(foo), which expands to the same thing.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes a bunch of non-functional changes -
return(foo); becomes return foo;
some statements are broken across lines for readability
some trailing whitespace is cleaned up
open_one_chan took four arguments, three of which could be
deduced from the first. Accordingly, they were eliminated.
some examples of "} else {" had a newline added
some whitespace cleanup in the indentation
lines_init got some control flow cleanup
some long lines were broken
removed another emacs-specific C formatting comment
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are a few functions which are declared to return something, but don't.
These are actually infinite loops which are forced to be declared as non-void.
This makes them all return 0.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There were a bunch of calls to uml_strdup dating from before kstrdup was
introduced. This changes those calls. It doesn't eliminate the definition
since there is still a couple of calls in userspace code (which should
probably call the libc strdup).
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Doesn't make much sense and unused.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mach_enable_irq/mach_disable_irq are never actually set, so let's remove
them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes cache memory parameter setting for the M32104 target. So
far, its performance seemed to have been degraded due to incorrect cache
parameter setting.
* arch/m32r/boot/setup.S: Set SFR(Special Fuction Registers) region
to be non-cachable explicitly.
* arch/m32r/mm/cache.c: Fix cache flushing routines not to switch off
the M32104 cache.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify _port2addr*() routines in arch/m32r/kernel/io_*.c to use
NONCACHE_OFFSET instead of hard-coding of a constant address.
This modification is also required to support an M3A-ZA36 FPGA eva board in
case an MMU-less synthesizable m32r core is used.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is for supporting a new target platform, Renesas M32104UT
evaluation board.
The M32104UT is an eval board based on an uT-Engine specification. This board
has an MMU-less M32R family processor, M32104.
http://www-wa0.personal-media.co.jp/pmc/archive/te/te_m32104_e.pdf
This board is one of the most popular M32R platform, so we have ported
Linux/M32R to it.
Signed-off-by: Naoto Sugai <Sugai.Naoto@ak.MitsubishiElectric.co.jp>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kconfig tweaks and tons of deletions.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With physical CPU hotplug, the CPU is hot removed and it should not receive
any interrupts. Disabling interrupt is much safer. This basically is what we
do in ia64 & x86.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Currently, during kexec reboot, IOAPIC is re-programmed back to virtual
wire mode if there was an i8259 connected to it. This enables getting
timer interrupts in second kernel in legacy mode.
o After putting into virtual wire mode, IOAPIC delivers the i8259 interrupts
to CPU0. This works well for kexec but not for kdump as we might crash
on a different CPU and second kernel will not see timer interrupts.
o This patch modifies the redirection table entry to deliver the timer
interrupts to the cpu we are rebooting (instead of hardcoding to zero).
This ensures that second kernel receives timer interrupts even on a
non-boot cpu.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we re-calibrate the frequency, it is likely that an interrupt (as for
example the main system clock) will be triggered by the system. Therefore
the calibration may not be accurate. This will also provide a fix to bug
#5266.
Many thanks to Larry Finger for helping resolving this issue.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix screen blanking on BIOSes that return APM_NOT_ENGAGED when APM enabled
screen blanking is not turned on.
The original code only tried to set the state on device 0x100, and then
0x1FF, and I added 0x101 to the mix too.
- Clean up logic in apm_console_blank().
- Prevent the error message from printing out twice.
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide basic support for the AMD Geode GX and LX processors.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed the unused variable "rv".
Signed-off-by: Daniel Marjamaki <daniel.marjamaki@comhem.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed the unused variable "rv".
Signed-off-by: Daniel Marjamaki <daniel.marjamaki@comhem.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Missing newline in printk.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 'make rodata read-only' patch in -mm exposes a latent bug in the 32-bit
change_page_attr() function, which causes certain CPUs (Those with NX
basically) to reboot instantly after pages are marked read-only.
The same bug got fixed a while back on x86-64, but never got propagated to
i386.
Stuart Hayes from Dell also picked up on this last June, but it never got
fixed, as the only thing affected by it aparently was the nvidia driver.
Blatantly stealing description from his post..
"It doesn't appear to be fixed (in the i386 arch). The
change_page_attr()/split_large_page() code will still still set all the
4K PTEs to PAGE_KERNEL (setting the _PAGE_NX bit) when a large page
needs to be split.
This wouldn't be a problem for the bulk of the kernel memory, but there
are pages in the lower 4MB of memory that's free, and are part of large
executable pages that also contain kernel code. If change_page_attr()
is called on these, it will set the _PAGE_NX bit on the whole 2MB region
that was covered by the large page, causing a large chunk of kernel code
to be non-executable."
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: <Stuart_Hayes@Dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we are using hotplug enabled kernel, then make bigsmp the default mode.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow SPARSEMEM to be enabled on non-numa x86 systems. This is made
dependant on EXPERIMENTAL also being set. When an in-tree user (such as
simulated numa) exists it should be made dependant on that.
The plan is to have no options and no selector as normal when
!EXPERIMENTAL. When EXPERIMENTAL we enable the FLATMEM and SPARSEMEM
options for X86_PC whilst maintaining DISCONTIGMEM and SPARSEMEM for NUMA.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark some key kernel datastructures readonly. This patch was previously
posted on Jun 28th but was back then not merged because nothing was enforcing
rodata anyway.. well that changed now :)
Patch by Christoph Lameter <christoph@lameter.com> and Dave Jones
<davej@redhat.com>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86-64 specific parts to make the .rodata section read only
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bug fix required for the .rodata work on x86-64:
when change_page_attr() and friends need to break up a 2Mb page into 4Kb
pages, it always set the NX bit on the PMD, which causes the cpu to consider
the entire 2Mb region to be NX regardless of the actual PTE perms. This is
fine in general, with one big exception: the 2Mb page that covers the last
part of the kernel .text! The fix is to not invent a new permission for the
new PMD entry, but to just inherit the existing one minus the PSE bit.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86 specific parts to make the .rodata section read only
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "temporary debugging check" which has managed to live for quite
some time, and is clearly unneeded. The mm can never be live at this point,
so clearly checking the LDT in the mm->context is redundant as well.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
APM BIOS code has a protective wrapper that runs it only on CPU zero. Thus,
no need to set APM BIOS segments in the GDT for other CPUs.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stop deleting NT bit from EFLAGS. See arch/i386/kernel/head.S line 223, which
does something even better.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PnP BIOS data, code, and 32-bit entry segments all have fixed limits as well;
set them in the GDT rather than adding more code. It would be nice to add
these fixups to the boot GDT rather than setting the GDT for each CPU; perhaps
I can wiggle this in later, but getting it in before the subsys init looks
tricky.
Also, make some progress on deprecating the ugly Q_SET_SEL macros.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The one remaining caller of set_limit, the PnP BIOS code, calls into the PnP
BIOS, passing kernel parameters in and out. These parameteres may be passed
from arbitrary kernel virtual memory, so they deserve strict protection to
stop a bad BIOS from smashing beyond the object size.
Unfortunately, the use of set_limit was badly botching this by setting the
limit in terms of pages, when it really should have byte granularity.
When doing this, I discovered my BIOS had the buggy code during the "get
system device node" call:
mov ax, es:[bx]
Which is harmless, but has a trivial workaround.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since APM BIOS segment limits are now fixed, set them in head.S GDT and don't
use the complicated _set_limit() macro expansion.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
APM BIOSes have many bugs regarding proper representation of the appropriate
segment limits for calling the BIOS. By default, APM_RELAX_SEGMENTS is always
turned on to support running the APM BIOS on these buggy machines. Keeping
64k limits poses very little danger to the kernel, because the pages where the
APM BIOS is located will always be in low physical memory BIOS areas, which
should already be marked reserved, and only buggy BIOSes would possibly
overstep the segment bounds with writes to data anyway.
Since forcing stricter limits breaks many machines and is not default
behavior, it seems reasonable to deprecate the older code which may cause APM
BIOS to fault.
If you really have a badly enough broken APM BIOS that you have to turn off
APM_RELAX_SEGMENTS, seems like the best recourse here would be to disable the
APM BIOS and / or not compile it into your kernel to begin with, and / or add
your system to the known bad list.
The reason I want to deprecate this code is there is underlying brokenness
with the set_limit macros, and getting rid of many of the call sites rather
than rewriting them seems to be the simplest and most correct course of
action.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So some 486 processors do have CR4 register. Allow them to present it in
register dumps by using the old fault technique rather than testing processor
family.
Thanks to Maciej for noticing this.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Other than apparently commonly assumed, the bound instruction does not
require the corresponding IDT entry to have DPL 3.
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move some code unrelated to any dealing with hardware bugs from i386's
bugs.h to a more logical place.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than blindly re-enabling interrupts in die(), save their state
upon entry and then restore that state.
If the kernel is in really bad condition and faults with interrupts disabled,
re-enabling them in die() may cause even more trouble, implying more chances
of data corruption.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make GDT page aligned and page padded to support running inside of a
hypervisor. This prevents false sharing of the GDT page with other hot
data, which is not allowed in Xen, and causes performance problems in
VMware.
Rather than go back to the old method of statically allocating the GDT
(which wastes unneded space for non-present CPUs), the GDT for APs is
allocated dynamically.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch improves the signal handling:
(1) It makes do_signal() static as it isn't called from anywhere outside of
the arch code.
(2) It removes the regs argument to all the static functions within that file,
using __frame instead (which is the same thing held in a global register).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch makes FRV signal handling work properly:
(1) After do_notify_resume() has been called, the work flags must be checked
again (there may be another signal to deliver or the process might require
rescheduling for instance).
(2) After the signal frame is set up on the userspace stack, ptrace() should
be given an opportunity to single-step into the signal handler.
(3) The error state from setting up a signal frame should be passed back up
the call chain.
(4) The segfault handler shouldn't be preemptively reset in the arch if we
fail to deliver a SEGV signal: force_sig() will take care of that.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch implements futex operations for the FRV architecture. The
operations are applicable to both MMU and no-MMU modes; though the EFAULT
handling will be a little bit of wasted space on the latter.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 3e9e7c1d0b (ppc32: cleanup AMCC PPC40x
eval boards to support U-Boot) broke the kernel for ML300 / EP405.
It still compiles as there's a weak definition of the function in
misc-embedded.c, but the kernel crashes as the bd_t fixup isn't performed.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some custom cards might not need PCI, without this patch, compilation fails.
Signed-off-by: Roger Blofeld <blofeldus@yahoo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were counting on the bootloader to init some stuff, like get the bus out of
reset and enable accesses.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch takes care of an errata of the MPC5200 by avoiding 32 bits access
in type 1 configuration accesses. All others accesses are still 32 bits wide.
It also adds some mb() since the simple out_be(...) are not sufficient in
this case.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The mpc52xx_pci_fixup_resources is not only called at init but also when there
is a pci hotplug like when a cardbus card is plugged in. So that function is
needed after init too.
Thanks to Asier Llano Palacios for reporting this.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current iomapping used MBAR_SIZE for the size argument of
io_block_mapping, resulting in a call to setbat with a size argument of 64k
which is invalid.
This patch correct this and maps the whole 0xf0000000->0xffffffff range so
that devices on the local bus are also included in the BAT mapping.
Thanks to Bernhard Kuhn from Metrowerks for pointing this out.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
That file is a left-over of the 'old' OCP model that should have been erased
during the change to platform model but I forgot it ...
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disable declaration of cpu variable in default_idle function when
building non-SMP kernels.
Signed-off-by: Otavio Salvador <otavio@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the not needed anymore "jumbo" member from ocp_func_emac_data.
Jumbo frame support is handled by PPC4xx EMAC driver internally now.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers for arm arch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make I2C_CLIENT_ALLOW_USE the default for all i2c clients. It doesn't
hurt if the usage count is actually never used for any given driver,
and allows for nice code simplifications in i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting RF (resume flag) allows a debugger to resume execution after a
code breakpoint without tripping the breakpoint again. It is reset by
the CPU after execution of one instruction.
Requested by Stephane Eranian:
"I am trying to the user HW debug registers on i386 and I am running
into a problem with ptrace() not allowing access to EFLAGS_RF for
POKEUSER (see FLAG_MASK). [ ... ] It avoids the need to remove the
breakpoint, single step, and reinstall. The equivalent functionality
exists on IA-64 and is allowed by ptrace()"
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/ia64/kernel/setup.c: In function `show_cpuinfo':
arch/ia64/kernel/setup.c:576: warning: long unsigned int format, different type arg (arg 12)
arch/ia64/kernel/setup.c:576: warning: long unsigned int format, different type arg (arg 13)
Introduced by 95235ca2c2
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Jared Hulbert
The following patch changes the bus arbiter controller settings
for the Intel PXA27x Application Processor Family. Up to 5%
better video performance. It parks the bus on the core while not
in use and sets the arbitration for other bus items. The patch
only applies changes to the Intel Mainstone development platform.
This patch is not compatible with preproduction Intel PXA27x
silicon.
This patch is based on the Intel Linux Preview Kit released to the
public on 25 Feb. 2005 found at
ftp://ftp.arm.linux.org.uk/pub/linux/arm/people/xscale/mainstone/02-25-2005/.
Signed-off-by: Justin A Treon <justin_treon@yahoo.com>
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
The expansion bus on the IXP46x NPU can be configured for either 32MiB or
16MiB windows and changing the configuration causes the base address for
each chip select for each region to change. Because of this, we cannot
hardcode the physical base as we currently do. This patch checks the
expansion bus configuration registers at runtime to determine the
appropriate window size. Note that this requires that the bootloader
already configured the device sizes appropriately, but I feel that is
valid assumption to make as the bootloader must configure and access
the flash window, the output display (LCD, LEDs, etc) window, and
other expansion bus devices.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dan Williams
Convert old-style serial devices to platform devices so that printk's are visible during the boot process.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
- remove unnecessary mappings
- rename mx1ads_device to cs89x0_device, because
that's what it is
- fix io/irq resource for cs89x0 device
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The SL-Cxx00 devices have a power control register in SCOOP that is
shared by both CF and MMC/SD card slots. The CF reset code was resetting
this register leading to various lockups as the MMC power was suddenly
lost. This patch handles the CPR register in a more sensitive manner.
It also removes some unneeded collie specific calls as the reset code
handles this.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
ARM doesn't use ACPI so ARM's apm implementation has no need to depend
on PM_LEGACY. This patch removes that dependency.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch moves a large chunk of the sharpsl_pm driver to
arch/arm/common so that it can be reused on other devices such as the
SL-5500 (collie). It also abstracts some functions from the core into
the machine and platform specific parts of the driver to aid reuse.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add platform code to enable the ohci device on the pxa27x based
Sharp Zaurus Cxx00 devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the manual, INT 6 is "invalid opcode", not "invalid operand".
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In particular, allow over-large read- or write-requests to be downgraded
to a more reasonable range, rather than considering them outright errors.
We want to protect lower layers from (the sadly all too common) overflow
conditions, but prefer to do so by chopping the requests up, rather than
just refusing them outright.
Cc: Peter Anvin <hpa@zytor.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The first of these changes s/hotplug/uevent/ was needed to
compile sn2_defconfig (ia64/sn). The other three files
changed are blind changes of all remaining bus_type.hotplug
references I could find to bus_type.uevent.
This patch attempts to finish similar changes made in the
gregkh-driver-kill-hotplug-word-from-driver-core Nov 22 patch.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.
This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Deepak Saxena
Add NAS 100d to machine build list and update to new 2.6.15 options.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
---
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Rod Whitby
PAGE_SHIFT is undeclared in include/asm-arm/arch-ixp4xx/memory.h, identified by the following kernel compilation error:
CC [M] sound/core/memory.o
In file included from include/asm/memory.h:27,
from include/asm/io.h:28,
from sound/core/memory.c:24:
include/asm/arch/memory.h: In function `__arch_adjust_zones':
include/asm/arch/memory.h:28: error: `PAGE_SHIFT' undeclared (first use
in this function)
This patch replaces my previous attempt at fixing this problem (Patch 3214/1) and is based on the following feedback:
Russell King wrote:
> The error you see came up on SA1100. The best solution was to move
> the __arch_adjust_zones() function out of line. I suggest ixp4xx
> does the same.
I have moved the function out of line into arch/arm/mach-ixp4xx/common-pci.c as suggested.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch removes referneces to gpio_isr_line_clear() from the
NAS 100d platform implementation.
Depends on 3192/1 and 3215/1
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Rod Whitby
This patch adds support for a new arm/ixp4xx machine - the Iomega NAS 100d network attached storage product. The NAS100D is a consumer device containing a 266MHz Intel IXP420 processor, 16MB of flash, 64MB of RAM, a 160Gb internal IDE hard disk, and 802.11b/g wireless on an Atheros mini-PCI card.
Work on porting the latest 2.6.x kernel to this device is being done by
the NSLU2-Linux project (the same team who maintains the port to the
Linksys NSLU2 device). In particular, the majority of this patch was
authored by Alessandro Zummo, based on the work done for MACH_NSLU2
support by the NSLU2-Linux core team of developers.
MACH_NAS100D (as implemented by this patch) can be enabled in jumbo
ixp4xx kernels without any affect on the other machines supported by
that kernel.
This patch applies cleanly against 2.6.15-rc7 and should be trivial to
apply to later kernel versions. It does not depend upon any other
patches.
Modified files (and number of lines inserted):
arch/arm/mach-ixp4xx/Kconfig | 8
arch/arm/mach-ixp4xx/Makefile | 1
include/asm-arm/arch-ixp4xx/hardware.h | 1
include/asm-arm/arch-ixp4xx/irqs.h | 9
include/asm-arm/arch-ixp4xx/nas100d.h | 75
arch/arm/mach-ixp4xx/nas100d-pci.c | 77
arch/arm/mach-ixp4xx/nas100d-power.c | 69
arch/arm/mach-ixp4xx/nas100d-setup.c | 133
-- Rod Whitby (NSLU2-Linux project lead)
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Other than interrupt masking purposes, this API is only used when
configuring interrupt lines and this patch moves that functionality
directly into the ixp4xx_set_irq_type() implementation as board level
PCI code should not need to worry about those details.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we now only build arch/arm/kernel/dma.c on machine types
which set ISA_DMA_API, we don't need to define MAX_DMA_CHANNELS
to 0 to indicate this - this definition becomes superfluous.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ISA_DMA_API tells the rest of the kernel if the ISA DMA API is
available. Select this symbol only on machine types which make
use of the ISA DMA API.
Make building of arch/arm/kernel/dma.c depend on this symbol -
if a machine does not support the ISA DMA API, it's pointless
building this file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to have DMA initialised at the same time as
interrupts. Move it to a core_initcall().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old __address element in struct scatterlist remained from older
kernels because the ARM DMA emulation code made use of it. Move
this field into struct dma_struct, and convert DMA emulation code
to setup a SG entry as required.
Also, convert DMA emulation code to use the new DMA API rather
than the PCI DMA API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the compiler to optimise the bus_to_virt(virt_to_bus())
transformation in the ARM ISA DMA interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CLPS711x, EPXA10DB and Integrator contained a dma.c file which has never
been built. Remove these redundant files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The function ia64_pci_legacy_write() returns 0 for everything
except errors. This return value gets sent back to the user from
pci_write_legacy_io(), making it look like every write fails. The trivial
patch below copies the behavior of the SGI sn machvec and does what
would be expected from something implementing a write() function.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/kernel/entry-armv.S has contained a comment suggesting
that asm/hardware.h and asm/arch/irqs.h should be moved into the
asm/arch/entry-macro.S include. So move the includes to these
two files as required.
Add missing includes (asm/hardware.h, asm/io.h) to asm/arch/system.h
includes which use those facilities, and remove asm/io.h from
kernel/process.c.
Remove other unnecessary includes from arch/arm/kernel, arch/arm/mm
and arch/arm/mach-footbridge.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We are coding the kernel link address into the makefiles, which is
invisibly dependent on PAGE_OFFSET. If PAGE_OFFSET is changed, the
makefiles also need to be changed.
Make adjustments such that the makefiles encode just the offset from
PAGE_OFFSET for the kernel link address, and use PAGE_OFFSET in the
linker scripts directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sonny has noticed hotplug CPU on ppc64 is broken in 2.6.15-*. One of the
problems is that htab_initialize_secondary is called when a cpu is being
brought up, but it is marked __init.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, we do not pass the correct start_pfn to e820_hole_size, to
calculate holes. Following patch fixes that.
The bug results in incorrect number of node_present_pages for each pgdat
and causes ugly output in /sys and probably VM inbalances.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Sighed-off-by: Shair Fultheim <shai@scalex86.org>
Sighed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix UML compilation when SKAS mode is disabled. Indeed, we were compiling
SKAS-only object files, which failed due to some SKAS-only headers being
excluded from the search path.
Thanks to the bug report from Pekka J Enberg.
Acked-by: Pekka J Enberg <penberg (at) cs ! helsinki ! fi>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Today, when compiling UML, I got warnings for two used unexported symbols:
readdir64 and truncate64. Indeed, my glibc headers are aliasing readdir to
readdir64 and truncate to truncate64 (and so on).
I'm then adding additional exports. Since I've no idea if the symbols where
always provided in the supported glibc's, I've added weak definitions too.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't use printk() where "current_thread_info()" is crap.
Until when we switch to running on init_stack, current_thread_info() evaluates
to crap. Printk uses "current" at times (in detail, ¤t is evaluated with
CONFIG_DEBUG_SPINLOCK to check the spinlock owner task).
And this leads to random segmentation faults.
Exactly, what happens is that ¤t = *(current_thread_info()), i.e. round
down $esp and dereference the value. I.e. access the stack below $esp, which
causes SIGSEGV on a VM_GROWSDOWN vma (see arch/i386/mm/fault.c).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi Kleen