This means the compiler doesn't need to use real division instructions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use of the net_device::priv field is deprecated.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch rewrites the TX power recalculation algorithms to scale better
with changed enviromnent. If there's low
TX traffic, the power will be checked against the desired values
every 60 seconds.
If there is high TX traffic, the check is redone every 2 seconds. This improves
the reaction times a lot and confuses the rate control less.
It will also reduce the time it initially takes to tune to a new TX power
value. With the old algorithm it could take about 30 to 45 seconds to settle to
a new power value. This will happen in about two to four seconds now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements a dynamic "ops" based PHY API.
This is needed in order to conveniently support future PHY types
to avoid the "switch"-hell.
This patch does not change any functionality. It just moves lots
of code from one place to another and adjusts it for the changed
data structures.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure the skb->data pointer points to the frame data, not the TX
descriptor. The frame dumping code relies on that.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware configuration registers such as antenna and channel configuration
can only be written when the radio is enabled. Previously, we didn't consider
this, so some configuration items could be set inconsistently after reenabling
the radio. This patch changes the config() handler to only reprogram the
hardware when the radio is enabled. Configuration changes that are made while
the radio is off are postponed until the radio is switched back on. We also
leave the radio turned off during initialization and only enable it when
requested by mac80211. This allows us to get rid of the DIRTY_CONFIG flag,
because the device is now guaranteed to be completely initialized when brought
up by mac80211.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a driver requests additional headroom it should
be mapped to DMA as well because it will be send to
the hardware as well (as form of extra descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.
The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)
Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kernel doc syntax for comments and remove a few unused macros.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AR_DurUpdateEna is set, the frame's duration field
is updated by the MAC based on the current rate.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the all of p54pci's receiver code out of the
bloated interrupt handler routine and into a less critical tasklet.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware supports 8 different queues and not only 4.
So, let's make some room for further tasks (ap/adhoc support)
in this area.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54_rx_frame_sent will alter the tx_queue. Therefore we should hold
the lock to protect against concurrent p54_assign_address calls.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever wondered why the signal was so bad with p54 compared to madwifi, or intel?
Well, if you have revision 1 rssi calibration curve points in your EEPROM, then wonder no more.
The firmware wants a extra 1 byte padding for every curve point. But someone forgot to put
them into the EEPROM's data structure...
So now, big question: what happens when we blindly "memcpy" these data points?
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/b43legacy/main.c
drivers/net/wireless/iwlwifi/iwl-3945-led.c
drivers/net/wireless/iwlwifi/iwl-led.c
drivers/net/wireless/iwlwifi/iwl-rfkill.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the internal ath9k implementation of multicast/broadcast frame
power save buffering (AP mode) in ath9k with use of mac80211
ieee80211_get_buffered_bc() mechanism. This removes quite a bit of
duplicated functionality and simplifies the driver part.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set some semi-random values for HT and add more queues to allow IEEE
802.11n association to be tested with mac80211_hwsim. This with the
latest hostapd git tree version can complete a simulated 802.11n
association successfully (with mac80211 client MLME).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and return errors for operations like join & scan that aren't possible
when the radio is turned off.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
and remove DISASSOCIATE because it's not in any of the specs and has
never been used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And while we're at it, grab min/max TX power from the firmware and use
that to validate incoming TX power requests from WEXT.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't trim the FCS before passing the frame to mac80211,
move TSF_TO_TU to core.h and delete more unused macros.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, Max RX-ampdu and mpdu-density are ath9k specific.
Rename appropriately.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes ath_vap_listen() and dma wrapper macros.
Also, Inline abuse is cleaned up and a few typos are fixed.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use direct pci functions instead.
Also, use sc_ht_info.tx_chan_width directly and remove ath_cwm_macmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use TX control flag IEEE80211_TX_CTL_ASSIGN_SEQ as a request to update
the seq# for the frames. This will likely require some further cleanup
to get seq# correctly for Beacons vs. other frames and also potentially
for multiple BSSes. Anyway, this is better than ending up sending out
most frames with seq# 0.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change moves ath9k to use mac80211-generated Beacon frames instead
of trying to allocate a single Beacon frame and then update it. In
addition, the remaining ath_skb_{map,unmap}_single() wrapper calls are
replaced with direct pci_{map,unmap}_single() calls in beacon.c. Power
save buffering for multicast/broadcast frames is not yet converted to
use mac80211-style (frames to be buffered inside mac80211, not in
driver).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add sc_rxflush and sc_noreset as bitfields to sc_flags.
Remove a few variables and function prototypes that are unused.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ah_opmode and sc_opmode are redundant.
This patch removes sc_opmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were 2 omitted readb's used on an iomap space. eliminate them
by using ioread8 instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We must not call dev_mc_add() from within our HW configure which happens
before we initialize and register the netdev. Do it in open() instead.
Thanks to Sebastian Siewior for tracking it down.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the checksum feature advertised in device flags. The hardware support
TCP/UDP over IPv4 and TCP/UDP over IPv6 (without IPv6 extension headers).
However, the kernel feature flags do not distinguish IPv6 with/without
extension headers.
Therefore, the driver needs to use NETIF_F_IP_CSUM instead of
NETIF_F_HW_CSUM since the latter includes all IPv6 packets.
A future patch can be created to check for extension headers and perform
software checksum calculation.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Manfred Spraul <manfred@colorfullife.com
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement set_mac_address for mcs7830. This enables me to use it with my
cable modem.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds USB device IDs for MosChip 7730 and Sitecom LN030
to the mcs7830 driver. The IDs have been reported to work without
further modifications.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Viktor Horvath <ViktorHorvath@gmx.net>
Cc: Robbert Wethmar <robbert@wethmar.nl>
Cc: Bart van der Klip <bklip@xs4all.nl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a ibmveth bug where bad UDP checksums are being transmitted
when checksum offloading is enabled.
The hypervisor does checksum offloading only on TCP packets, so ibmveth calls
skb_checksum_help() for any other protocol. The bug happens because
the packet is being modified after the DMA map, so we would need a memory
barrier before making the hypervisor call. Reordering the code so that the
DMA map happens after skb_checksum_help() has the additional advantage of
fixing a DMA map leak if skb_checksum_help() where to fail.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fixes dev_kfree_skb happening too many times when hso_start_net_device
is called from hso_resume.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The atl1 driver is causing stalled connections and file corruption
whenever TSO is enabled. Two examples are here:
http://lkml.org/lkml/2008/7/15/325http://lkml.org/lkml/2008/8/18/543
Disable TSO by default until we can determine the source of the
problem.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Doesn't cause problems (yet) because err gets zeroed earlier.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Disable support for device 8086:10E8. Currently the result of loading the
driver with the device present causes system instability.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
CC [M] drivers/net/skfp/ess.o
drivers/net/skfp/ess.c: In function 'ess_send_response':
drivers/net/skfp/ess.c:513: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c: In function 'ess_send_alc_req':
drivers/net/skfp/ess.c:609: warning: cast from pointer to integer of different size
drivers/net/skfp/ess.c:639: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The real_num_tx_queues was not being set when in MSI-X only mode. This patch
corrects that path so all interrupt types are correctly configured.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ethtool -d is reading the EICR and ICR registers which is currently
clearing these registers and masking off interrupts. To prevent this we
read the EICS and ICS equivilents as they can be read without clearing or
masking.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set the EICS bit for each of the RX queues at least once every 2 seconds to
prevent the rx queues from stalling.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The leak hurts with swiotlb and jumbo frames.
Fix http://bugzilla.kernel.org/show_bug.cgi?id=9468.
Heavily hinted by Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Timothy J Fontaine <tjfontaine@atxconsulting.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
VLAN filtering is broken, due to reading the incorrect register for
the VLAN filtering settings. Fixed by reading/writing the correct
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
so update things accordingly
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
bintval is set to the initial value at .config_interface which is too
late, since it overwrites previously set value from .config. Move the
initialization to the .add_interface.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacons setup and config was racy with beacon send. Ensure that
ISR and reset functions see consistent state of bbuf.
Use also dev_kfree_skb_any in ath5k_txbuf_free since we call it
from atomic now.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the AP rejects a Shared Key authentication request, try Open System
auth too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return errors from request_firmware() (like other drivers that do
firmware load on device open) and make up plausible codes for other
error conditions. Gives userspace tools like NetworkManager a clue that
firmware may be missing when the result of setting IFF_UP is ENOENT.
Signed-off-by: Dan Williams <dcbw@redhat.com>
v2: fix reversed check of atmel_wakeup_firmware() in probe_atmel_card()
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The multi queue support is still disabled by default for the bnx2x
(needs some more testing and validation), but there are 2 obvious bug in
it which are fixed in this patch
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing the order of enabling and disabling NAPI and the interrupts
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load failures were not handled correctly
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TPA initialization is part of the FW internal memory initialization
and so it is moved to the appropriate function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing the lock timeout to 5 seconds instead of 1 second to minimize
the chance of failures due to timeout
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After iSCSI boot, the HW lock should only protect the flag so only the
first function will reset the chip and not then entire chip reset
process
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The A1021G board is also using the fan failure mechanism in the same way
the A1022G board does
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The has Rx work check was wrong: when the FW was at the end of the page,
the driver was already at the beginning of the next page. Since the
check only validated that both driver and FW are pointing to the same
place, it concluded that there is still work to be done. This caused
some serious issues including long latency results on ping-pong test and
lockups while unloading the driver in that condition.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv643xx_eth hardware ignores the lower three bits of the buffer
size field in receive descriptors, causing the reception of full-sized
packets to fail at some MTUs. Fix this by rounding the size of
allocated receive buffers up to a multiple of eight bytes.
While we are at it, add a bit of extra space to each receive buffer so
that we can handle multiple vlan tags on ingress.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When we are low on memory, the assumption that every descriptor in the
receive ring will have an skbuff associated with it does not hold.
rxq_process() was assuming that if the receive descriptor it is working
on is not owned by the hardware, it can safely be processed and handed
to the networking stack. But a descriptor in the receive ring not being
owned by the hardware can also happen when we are low on memory and did
not manage to refill the receive ring fully.
This patch changes rxq_process()'s bailout condition from "the first
receive descriptor to be processed is owned by the hardware" to "the
first receive descriptor to be processed is owned by the hardware OR
the number of valid receive descriptors in the ring is zero".
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Nicolas Pitre noted that mv643xx_eth_poll was incorrectly using
non-IRQ-safe locks while checking whether to wake up the netdevice's
transmit queue. Convert the locking to *_irq() variants, since we
are running from softirq context where interrupts are enabled.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Commit 12e4ab79cd ("mv643xx_eth: be
more agressive about RX refill") changed the condition for the receive
out-of-memory timer to be scheduled from "the receive ring is empty"
to "the receive ring is not full".
This can lead to a situation where the receive out-of-memory timer is
pending because a previous rxq_refill() didn't manage to refill the
receive ring entirely as a result of being out of memory, and
rxq_refill() is then called again as a side effect of a packet receive
interrupt, and that rxq_refill() call then again does not succeed to
refill the entire receive ring with fresh empty skbuffs because we are
still out of memory, and then tries to call add_timer() on the already
scheduled out-of-memory timer.
This patch fixes this issue by changing the add_timer() call in
rxq_refill() to a mod_timer() call. If the OOM timer was not already
scheduled, this will behave as before, whereas if it was already
scheduled, this patch will push back its firing time a bit, which is
safe because we've (unsuccessfully) attempted to refill the receive
ring just before we do this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When a receive interrupt occurs, mv643xx_eth would first process the
receive descriptors and then ACK the receive interrupt, instead of the
other way round.
This would leave a small race window between processing the last
receive descriptor and clearing the receive interrupt status in which
a new packet could come in, which would then 'rot' in the receive
ring until the next receive interrupt would come in.
Fix this by ACKing (clearing) the receive interrupt condition before
processing the receive descriptors.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Use the MIC algorithm from the crypto subsystem.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Read the packet data off the hardware and straight into an skb in the
interrupt. We have to do this in case we don't process the tasklet in
time.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Includes basic plumbing to get the data into firmware, and retrieve it.
SIOCxIWGENIE simply record (and return) the IE, and do not act on it.
SIOCxIWENCODEEXT, SIOCxIWAUTH and SIOCSIWMLME should be as functional as
the driver will support.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The macro identifiers for the various ioctls required for WPA support
are longer than those currently used by the driver. This makes it messy
to keep line length below 80 character.
By defining a macro to initialise the handler table, we recover the
common text.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to send more wevents from the work thread. We will need
to do this to support WPA.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For WPA support we need to encode NONE, WEP and TKIP in the encoding
parameter. In anticipation of this we need to change the usage away from
the current boolean usage.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This provides more information than the standard Agere scan, including
the WPA IE.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx control word has moved into the 802.11 header area on these
firmwares.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware download is enabled for Agere in orinoco_cs. Symbol firmware
download has been moved out of spectrum_cs into orinoco_cs. Firmware
download is not enabled for Intersil.
Symbol based firmware is restricted to only download on spectrum_cs
based cards.
The firmware names are hardcoded for each firmware type.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add programming initialisation and termination functions.
Add checks to avoid overrunning the firmware image or PDA areas.
Extra algorithm to program PDA values using defaults where necessary.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure PDA read is terminated.
Prevent invalid programming blocks from causing reads outside the
firmware image
Turn off aux stuff when finished.
Option to program in limited block sizes (controlled by macro).
Option to read PDA from EEPROM.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the functionality from spectrum_cs to hermes_dld in preparation for
making it more generic and usable by other orinoco drivers.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current synchronous execution function doesn't work
for certain Hermes commands which clear the MAGIC number from
SWSUPPORT0. These commands seem to be related to initialisation or
programming, for example HERMES_CMD_INIT.
Replicate hermes_docmd_wait for commands which clear the MAGIC number
from SWSUPPORT0. This version accepts two extra arguments which are
passed straight to the firmware.
Functionality copied out of hermes_init.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hermes_issue_cmd now takes two more parameters.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report channel, beacon interval and capabilities.
Use WEXT defines instead of magic numbers.
State quality stats in dB.
Also a few changes to keep line length less than 80.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the ESSID to the card.
This allows 'iwlist eth1 scan essid <essid>' to work, and will help
with routers setup not to broadcast the ESSID.
Signed-off-by: David Kilroy <kilroyd@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's been a long time, but fullmac prism54 driver is still around...
I think we should rename every prism54* in order to avoid some
confusion about "what is actually what" in the future ;-).
Thanks-to: Maxi <maxi@daemonizer.de>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a module parameter to rt61 and rt73 to disable
HW crypto. The option should only be checked when
determining if the SUPPORT_HW_CRYPTO flag should
be set or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can optimize lna calculation in IRQ context by
calculating most of the value during the config() callback
when most of the value is actually influenced.
This will be required later by rt2800pci and rt2800usb as
well, since they need the lna_gain value during config().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
set the short preamble flag in ieee80211_rx_status for frames received with a
short preamble.
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Channel information which is read from EEPROM should
be read into an array containing per-channel information.
This removes the requirement of multiple arrays and makes
the channel handling a bit cleaner and easier to expand.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt73usb supports hardware encryption.
rt73usb supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt61pci supports hardware encryption.
rt61pci supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various rt2x00 devices support hardware encryption.
Most of them require the IV/EIV to be generated by mac80211,
but require it to be provided seperately instead of within
the frame itself. This means that rt2x00lib should extract
the data from the frame and place it in the frame descriptor.
During RX the IV/EIV is provided in the descriptor by the
hardware which means that it should be inserted into the
frame by rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas thin firmware only supports usb devices, but the usb functions have
been kept separate to ease future support for other devices.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains most of the libertastf driver, just lacking command helper
functions and usb specific functions. Currently, monitor, managed, ap and mesh
interfaces are supported. Even though this driver supports the same hardware as
the "libertas" driver, it uses a different (thin) firmware, that makes it
suitable for a mac80211 driver.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_hdrlen_from_skb internally checks that the skb is long
enough to hold the full header, or it returns 0 if not. The check in
ath5k does not check this case and assumes it always got the actual
header length which it then checks against the skb->len plus some headroom.
Change to ieee80211_hdrlen which always returns the hdrlen and keep the
existing headroom check.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds another level for debugging host command. This adds an
option to suppress the debug prints for sensitivity and link quality
commands.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes struct iwl4965_lq_mngr it is not used.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
num_tbs is unsigned so the test doesn't work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove drivers own implementation of radiotap in favor of the generic one
provided by mac80211.
also remove priv->add_radiotap because it is not used any more.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cleanup the rates structures used by ath5k. instead of separate driver and
mac80211 rate structures we now setup a static ieee80211_rate array and use it
directly. no conversion between two different rate structures has to be done
any more. a lot of unused and confusing junk was deleted.
renamed ath5k_getchannels into ath5k_setup_bands because this is what it does.
rewrote it to copy the bitrates correctly for each band. this is necessary for
running different hardware with the same driver (e.g. 5211 and 5212 based
cards).
add special handling of rates for AR5211 chipsets: it uses different rate codes
for CCK rates (which are actually like the other chips but with a 0xF mask).
setup a hardware code to rate index reverse mapping table for getting the rate
index of received frames.
the rates for control frames which have to be set in
ath5k_hw_write_rate_duration are now in one single array.
drivers/net/wireless/ath5k/ath5k.h: Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were 3 code copy and pastes of reset. Unify the resets and place
in separate function.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not allowed to use NETDEV_TX_BUSY in tx path anymore.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables draft-802.11s Mesh Point operation. For that we need mesh
beaconing. Tested with AR5212/AR5213 PCI card against Zydas and b43 mesh
nodes.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To use these features, copy the boot2 and firmware images to /lib/firmware and:
echo <boot2_image_name> > /sys/class/net/ethX/lbs_flash_boot2
echo <firmware_image_name> > /sys/class/net/ethX/lbs_flash_fw
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add locking and non-locking versions of if_usb_prog_firmware to support
programming firmware after and before driver bring-up respectively. Add more
suitable error codes for firmware programming process. Add capability checks
for persistent features before attempting to use them.
Based on patches from Brajesh Dave and Priyank Singh.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tx/Rx descriptor flags are common between rtl818x devices, only with
additions for newer chips, thus use same flags in the code.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/ath5k/base.c
drivers/net/wireless/b43/main.c
drivers/net/wireless/ipw2100.c
drivers/net/wireless/ipw2200.c
drivers/net/wireless/iwlwifi/iwl-3945.c
drivers/net/wireless/iwlwifi/iwl-4965.c
drivers/net/wireless/iwlwifi/iwl-5000.c
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/iwlwifi/iwl-eeprom.c
drivers/net/wireless/iwlwifi/iwl-hcmd.c
drivers/net/wireless/iwlwifi/iwl-power.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txdone_entry_desc_flags is used with __set_bit and test_bit which
bit-shift the values, so don't bit-shift the flags in the enum.
Also make sure flags are initialized before being used.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In trying to help users on the Ubuntu Bugzilla, I discovered another
BCM4306 with the Bluetooth Coexistence programming error in the SPROM.
This patch is contingent on the one that added the Linksys device with
subdevice code of 0x0014.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Only important for USB V1 Adaptors)
If an incoming frame wasn't accepted by p54_rx function
the skb will be reused for new frames...
But, we must not forget to set the skb's data pointers into
the same state in which it was initialized by p54u_init_urbs.
Otherwise we either end up with 16 bytes less on every requeue,
or if a new frame is worthy enough to be accepted, the data is
in the wrong place (urb->transfer_buffer wasn't updated!) and mac80211
has a hard time to recognize it...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->tx_hdr_len is set by the driver _after_ it called p54_init_common.
While this isn't much a problem for any PCI or ISL3887 cards/sticks,
because they don't need any extra header and therefore tx_hdr_len is
zero for them...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add newlines at printk outputs to not break dmesg.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB ID for a Netgear WG111v3.
Signed-off-by: matthieu Barthélemy <bonsouere@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings