Commit graph

16 commits

Author SHA1 Message Date
Tejun Heo
8e16f94122 [PATCH] ahci: do not powerdown during initialization
ahci_init_controller() calls ahci_deinit_port() to make sure the
controller is stopped before initializing the controller.  In turn,
ahci_deinit_port() invokes ahci_power_down() to power down the port.
If the controller supports slumber mode, the link is put into it.

Unfortunately, some devices don't implement link powersaving mode
properly and show erratic behavior after link is put into slumber
mode.  For example, HL-DT-ST DVD-RAM GSA-H30N completely locks up on
slumber transition and can only be recovered with the *REAL* hard
reset - power removal and reapply.

Note that this makes the first probing reset different from all
others.  If the above dvd-ram is hotplugged after ahci is initialized,
no problem occurs because ahci is already fully initialized with phy
powered up.  So, this might also be the reason for other weird AHCI
initial probing abnormalities.

This patch moves power up/down out of port init/deinit and call them
only when needed.

Power down is now called only when suspending.  As system suspend
usually involves powering down 12v for storage devices, this shouldn't
cause problem even if the attached device doesn't support slumber
mode.  However, in partial power management and suspend failure cases,
devices might lock up after suspend attempt.  I thought about removing
transition to slumber mode altogether but ahci spec mandates it before
HBA D3 state transition.  Blacklisting such devices might be the
solution.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-12-03 17:56:29 +09:00
Tejun Heo
648a88be4a [PATCH] ahci: honor PORTS_IMPL on ICH8s
Some ICH8s use non-linear port mapping.  ahci driver didn't use to
honor PORTS_IMPL and this made ports after hole nonfunctional.  This
patch makes ahci mark those ports as dummy and properly initialize all
the implemented ports after the dummies.

As it's unknown whether other AHCIs implement PORTS_IMPL register
properly, new board id board_ahci_pi is added and selectively applied
to ICH8s.  All other AHCIs continue to use linear mapping regardless
of PORTS_IMPL value.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:44:53 -05:00
Tejun Heo
98fa4b60c6 [PATCH] ahci: preserve PORTS_IMPL over host resets
Instead of writing 0xf blindly, preserve the content of write-once
PORTS_IMPL register over host resets.

This patch is taken from Jeff Garzik's AHCI init update patch.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:41:31 -05:00
Jeff Garzik
415ae2b5c0 [libata] ahci: Match PCI class code for AHCI
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:41:31 -05:00
Tejun Heo
ad616ffbda [PATCH] ahci: update ahci-vt8251 reset sequence
ahci-vt8251

* requires hardreset after PHY status change

* doesn't clear BSY on signature FIS after hardreset

* needs SError cleared for the port to operate after hardreset

This patch implements ahci_vt8251_hardreset() and sets
ATA_FLAG_HRST_TO_RESUME to handle the above behaviors.  This fixes EH
including hotplug on vt8251.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:41:30 -05:00
Tejun Heo
4aeb0e3283 [PATCH] ahci: kill AHCI_FLAG_RESET_NEEDS_CLO
Now that ahci_softreset() is fixed to automatically perform CLO if
BSY/DRQ is set on entry, AHCI_FLAG_RESET_NEEDS_CLO is redundant.  Kill
it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:41:29 -05:00
Tejun Heo
4166955335 [PATCH] ahci: ignore PORT_IRQ_IF_ERR on JMB controllers
JMicron AHCI controllers set PORT_IRQ_IF_ERR on device errors.  The
IRQ status bit indicates interface error or protocol mismatch and ahci
driver interprets it into AC_ERR_ATA_BUS.  So, whenever an ATAPI
device raises check condition, ahci interprets it as ATA bus error and
thus resets it which, in turn, raises check condition thus creating a
reset loop and rendering the device unuseable.

This patch makes JMB controllers ignore PORT_IRQ_IF_ERR when
interpreting error condition.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Justin Tsai <justin@jmicron.com>
2006-11-29 14:57:44 +09:00
Jason Gaston
f33d625f40 [PATCH] ahci: AHCI mode SATA patch for Intel ICH9
This patch adds the Intel ICH9 AHCI controller DID's for SATA support.

Signed-off-by:  Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-28 03:45:13 -05:00
Peer Chen
895663cd92 [libata] Add support for AHCI controllers of MCP67.
Signed-off-by: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-02 17:59:46 -05:00
Tejun Heo
1244a19cde [PATCH] ahci: fix status register check in ahci_softreset
ahci_softreset() used to use ahci_tf_read() which reads D2H_REG area
to check for the Status register.  However, this area is zeroed on
initialization and not set by initial signature FIS.  Replace it with
ahci_check_status().

This bug prevented CLO code from being activated whenever BSY and/or
DRQ is set prior to softreset.  This fix makes
AHCI_FLAG_RESET_NEEDS_CLO flag redundant.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-01 04:20:45 -05:00
Alan Cox
12a87d36b3 [PATCH] ahci: readability tweak
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-10-21 15:18:59 -04:00
David Howells
7d12e780e0 IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.

Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 15:10:12 +01:00
Jeff Garzik
54bb3a94b1 [libata] Use new PCI_VDEVICE() macro to dramatically shorten ID lists
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-27 22:20:11 -04:00
Jeff Garzik
9bec2e3852 [libata] Trim trailing whitespace. 2006-08-31 00:02:15 -04:00
Jeff Garzik
cca3974e48 libata: Grand renaming.
The biggest change is that ata_host_set is renamed to ata_host.

* ata_host_set			=> ata_host
* ata_probe_ent->host_flags	=> ata_probe_ent->port_flags
* ata_probe_ent->host_set_flags	=> ata_probe_ent->_host_flags
* ata_host_stats		=> ata_port_stats
* ata_port->host		=> ata_port->scsi_host
* ata_port->host_set		=> ata_port->host
* ata_port_info->host_flags	=> ata_port_info->flags
* ata_(.*)host_set(.*)\(\)	=> ata_\1host\2()

The leading underscore in ata_probe_ent->_host_flags is to avoid
reusing ->host_flags for different purpose.  Currently, the only user
of the field is libata-bmdma.c and probe_ent itself is scheduled to be
removed.

ata_port->host is reused for different purpose but this field is used
inside libata core proper and of different type.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-24 03:19:22 -04:00
Jeff Garzik
c6fd280766 Move libata to drivers/ata. 2006-08-10 07:31:37 -04:00
Renamed from drivers/scsi/ahci.c (Browse further)