Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_<level> for printk
Use temporary instead of multiple pr_conts
Coalesce formats.
Save a few bytes of object code too:
$ size drivers/net/ethernet/intel/e1000/e1000_main.o*
text data bss dec hex filename
60507 369 14120 74996 124f4
drivers/net/ethernet/intel/e1000/e1000_main.o.new
60717 369 14176 75262 125fe
drivers/net/ethernet/intel/e1000/e1000_main.o.old
Removed printing of pktdata.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Separate a complicated bit of e1000_config_dsp_after_link_change
into a new static function e1000_1000Mb_check_cable_length.
Reduces indentation and adds a bit of clarity.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent discussions on LKML, kernel-janitors, linux-wireless and netdev
have suggested boolean comparisons should use logical operators instead of
equality comparisons with true/false.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to pass the Ethernet Frame Checksum
(FCS) up the stack. Useful when sniffing packets.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Good for testing the RX logic for bad CRC handling.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to receive all frames available, including
those with bad FCS, un-matched vlans, ethernet control frames,
and more.
Tested by sending frames with bad FCS.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This can aid with testing the RX logic for bad
CRCs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables enabling/disabling reception of the Ethernet
FCS. This can be useful when sniffing packets.
For e1000e, enabling RXFCS can change the default
behaviour for how the NIC handles CRC. Disabling RXFCS
will take the NIC back to defaults, which can be configured
as part of the module options.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reset the state of addr_assign_type to NET_ADDR_PERM as soon as
the MAC get changed via .ndo_set_mac_address.
v2: use bitops to reset addr_assign_type
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per ./Documentation/CodingStyle, goto statements are acceptable for the
centralized exiting of functions when there are multiple exit points which
share common work such as cleanup. When no common work is required for
multiple exit points, the function should just return at these exit points
instead of doing an unnecessary jump to a centralized return. This patch
cleans up the inappropriate use of goto statements, and removes unnecessary
variables (or move to a smaller scope) where possible as a result of the
cleanups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unlikely event that e1000_poll_fiber_serdes_link_generic() is called
and it returns an error, the returned error code value is not propagated to
the caller of e1000e_setup_fiber_serdes_link().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unlikely event that e1000_setup_link_ich8lan() returns an error,
the returned error code value is not propagated to the caller of
e1000_init_hw_ich8lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fall-through to a return statement that effectively does the same.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ret_val gets initialized to -E1000_ERR_NVM and never set differently, so
get rid of it and just return -E1000_ERR_NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unlikely event that e1e_wphy() returns an error, the returned error
code is not propogated to the caller of e1000_set_d3_lplu_state_ich8lan().
With this change, there is a rare possibility that ret_val might not get
set so it must be initialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These are a few instances of returning a value that can only be 0 so just
use a 'return 0' to make it more obvious.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just return the appropriate value.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unlikely event that e1000e_setup_copper_link() returns an error,
the returned error code value is not propogated to the caller of
e1000_setup_copper_link_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unlikely event that e1e_wphy() returns an error, the returned error
code value is not propogated to the caller of
e1000_cfg_kmrn_10_100_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the following functions, rename the generic 'out' goto label to the more
descriptive 'release' to indicate the type of common work that is done
before exiting the functions. No functional change, cosmetic only.
e1000_sw_lcd_config_ich8lan()
e1000_oem_bits_config_ich8lan()
e1000_init_phy_wakeup()
e1000e_write_phy_reg_bm()
e1000e_read_phy_reg_bm()
e1000e_read_phy_reg_bm2()
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are two exit points of e1000e_write_nvm_spi() which require the
nvm->ops.release() function pointer called just before exiting.
Consolidate the two duplicate pieces of common work with a goto. With
this change, the value ret_val will need to be returned instead of 0.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Booleans should not be compared to true or false
but be directly tested or tested with !.
Done via cocci script:
@@
bool t;
@@
- t == true
+ t
@@
bool t;
@@
- t != true
+ !t
@@
bool t;
@@
- t == false
+ !t
@@
bool t;
@@
- t != false
+ t
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renamed dev_hw_addr_random to eth_hw_addr_random() to reflect that
this function only assign a random ethernet address (MAC). Removed
the second parameter (u8 *hwaddr), it's redundant since the also
given net_device already contains net_device->dev_addr.
Set it directly.
Adapt igbvf and ixgbevf to the changed function.
Small fix for ixgbevf_probe(): if ixgbevf_sw_init() fails
(which means the device got no dev_addr) handle the error and
jump to err_sw_init as already done by igbvf in similar case.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change combines a number of post-DMA Rx packet processing functions
into a single function. The advantage of this is that it combines most of
the Rx descriptor processing into one spot so it should all be warm in the
cache.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It doesn't make much sense to differentiate between advanced and legacy
descriptors when the only descriptors that ixgbe uses are advanced
descriptors. As such we can drop the _ADV suffix since all ixgbe
descriptors are automatically advanced.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds a small function for testing Rx status bits in the
descriptor. The advantage to this is that we can avoid unnecessary
byte swaps on big endian systems.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we always clear the status/error bits in the
Rx descriptor in the allocation path instead of the cleanup path. The
advantage to this is that we spend less time modifying data. As such we
can modify the data once and then let it go cold in the cache instead of
writing it, reading it, and then writing it again.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to address the fact that RSC has not been setting the
gso_size value on the skb. As a result performance on lossy TCP
connections was negatively impacted. This change resolves the issue by
setting gso_size to the average size for incoming packets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change addresses several issue.
First I had left the use of the next and prev skb pointers floating around
in the code and they were overdue to be pulled since I had rewritten the
RSC code in the out-of-tree driver some time ago to address issues brought
up by David Miller in regards to this.
I am also now defaulting to always leaving the first buffer unmapped on any
packet and then unmapping it after we read the EOP descriptor. This allows
a simplification of the path with less branching.
Instead of counting packets received the code was changed some time ago to
track the number of buffers received. This leads to inaccurate counting
when you compare numbers of packets received by the hardware versus what is
tracked by the software. To correct this I am revising things so that the
append_cnt value for RSC accurately tracks the number of frames received.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a warning about unused function when CONFIG_PM_SLEEP
is not selected in the kernel config:
igb_main.c: warning: `igb_suspend` defined but not used [W-unused-function]
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000_init_mac_params_XXX() functions (where XXX is one of the three
MAC-family types 80003es2lan, 82571 and ich8lan) was not meant to require a
pointer to the adapter struct but does require a pointer to the hw struct.
Pass that pointer in to the functions instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
v2 - replaced mac->autoneg_failed == false with !mac->autoneg_failed
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...and convert some goto's which simply return to just return.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
warning: comparison of unsigned expression < 0 is always false
Remove an unnecessary test that is reported when compiling driver with W=1.
The test is unnecessary because Intel wired GbE hardware older (i.e. less)
than 82571 is not supported by this driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the number of tx/rx queues changes the ethtool ioctl
ETHTOOL_GSTATS may overrun the userspace buffer. This
occurs because the general practice in user space to
query stats is to issue a ETHTOOL_GSSET cmd to learn the
buffer size needed, allocate the buffer, then call
ETHTOOL_GSTIRNGS and ETHTOOL_GSTATS. If the number of
real_num_queues is changed or flow control attributes
are changed after ETHTOOL_GSSET but before the
ETHTOOL_GSTRINGS/ETHTOOL_GSTATS a user space buffer
overrun occurs.
To fix the overrun always return the max buffer size
needed from get_sset_count() then return all strings
and stats from get_strings()/get_ethtool_stats().
This _will_ change the output from the ioctl() call
which could break applications and script parsing in
theory. I believe these changes should not break existing
tools because the only changes will be more {tx|rx}_queues
and the {tx|rx}_pb_* stats will always be returned.
Existing scripts already need to handle changing number
of queues because this occurs today depending on system
and current features. The {tx|rx}_pb_* stats are at the
end of the output and should be handled by scripts today
regardless.
Finally get_ethtool_stats and get_strings are free-form
outputs tools parsing these outputs should be defensive
anyways. In the end these updates are better then
having a tool segfault because of a buffer overrun.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Users expect the up2tc mapping to be maintained across a DCB
enable/disable/enable transition. And since we maintain all
the other DCB attributes we should do this for up2tc mappings
as well just to be consistent. Also without this we break
user space applications that expect this to occur that
previously worked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the netdev is already in NETREG_UNREGISTERING/_UNREGISTERED state, do not
update the real num tx queues. netdev_queue_update_kobjects() is already
called via remove_queue_kobjects() at NETREG_UNREGISTERING time. So, when
upper layer driver, e.g., FCoE protocol stack is monitoring the netdev
event of NETDEV_UNREGISTER and calls back to LLD ndo_fcoe_disable() to remove
extra queues allocated for FCoE, the associated txq sysfs kobjects are already
removed, and trying to update the real num queues would cause something like
below:
...
PID: 25138 TASK: ffff88021e64c440 CPU: 3 COMMAND: "kworker/3:3"
#0 [ffff88021f007760] machine_kexec at ffffffff810226d9
#1 [ffff88021f0077d0] crash_kexec at ffffffff81089d2d
#2 [ffff88021f0078a0] oops_end at ffffffff813bca78
#3 [ffff88021f0078d0] no_context at ffffffff81029e72
#4 [ffff88021f007920] __bad_area_nosemaphore at ffffffff8102a155
#5 [ffff88021f0079f0] bad_area_nosemaphore at ffffffff8102a23e
#6 [ffff88021f007a00] do_page_fault at ffffffff813bf32e
#7 [ffff88021f007b10] page_fault at ffffffff813bc045
[exception RIP: sysfs_find_dirent+17]
RIP: ffffffff81178611 RSP: ffff88021f007bc0 RFLAGS: 00010246
RAX: ffff88021e64c440 RBX: ffffffff8156cc63 RCX: 0000000000000004
RDX: ffffffff8156cc63 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88021f007be0 R8: 0000000000000004 R9: 0000000000000008
R10: ffffffff816fed00 R11: 0000000000000004 R12: 0000000000000000
R13: ffffffff8156cc63 R14: 0000000000000000 R15: ffff8802222a0000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#8 [ffff88021f007be8] sysfs_get_dirent at ffffffff81178c07
#9 [ffff88021f007c18] sysfs_remove_group at ffffffff8117ac27
#10 [ffff88021f007c48] netdev_queue_update_kobjects at ffffffff813178f9
#11 [ffff88021f007c88] netif_set_real_num_tx_queues at ffffffff81303e38
#12 [ffff88021f007cc8] ixgbe_set_num_queues at ffffffffa0249763 [ixgbe]
#13 [ffff88021f007cf8] ixgbe_init_interrupt_scheme at ffffffffa024ea89 [ixgbe]
#14 [ffff88021f007d48] ixgbe_fcoe_disable at ffffffffa0267113 [ixgbe]
#15 [ffff88021f007d68] vlan_dev_fcoe_disable at ffffffffa014fef5 [8021q]
#16 [ffff88021f007d78] fcoe_interface_cleanup at ffffffffa02b7dfd [fcoe]
#17 [ffff88021f007df8] fcoe_destroy_work at ffffffffa02b7f08 [fcoe]
#18 [ffff88021f007e18] process_one_work at ffffffff8105d7ca
#19 [ffff88021f007e68] worker_thread at ffffffff81060513
#20 [ffff88021f007ee8] kthread at ffffffff810648b6
#21 [ffff88021f007f48] kernel_thread_helper at ffffffff813c40f4
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue in which RSC will generate corrupted frames when
PAGE_SIZE is larger than 8K. Specifically it looks like that in 2.6.39 a
change was made so that GRO would always have at least 16 frags available
for coalescing, but the ixgbe RSC logic was not updated. As such the RSC
feature would generate a frame larger than 64K and then overflow the value
in the IP length field.
To correct that I am now basing things on the PAGE_SIZE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A check for the number of VFs allocated should have used a greater than
equal operator instead of just greater than. This caused allocation of
exactly 32 VFs to not enable the PF transmit and receive enables.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This bug exists in 3.2 stable as well as 3.3 release candidates.
CC: stable@vger.kernel.org
Reported-by: David Ahern <daahern@cisco.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This is applicable to 3.2+ kernels.
CC: stable@vger.kernel.org
Reported-by: David Ahern <daahern@cisco.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit d5bc77a223 broke Wake-on-LAN by
inadvertently dropping the enabling of DMA receives.
Restore the enabling of DMA receives for WoL.
This is applicable to 3.1+ stable trees.
CC: stable@vger.stable.org
Reported-by: Tobias Klausmann <klausman@schwarzvogel.de>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Tested-by: Tobias Klausmann <klausman@schwarzvogel.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup of some whitespace and indentation of a single code block.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WARNING: min() should probably be min_t(unsigned int, 4, skb->data_len)
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the existing hw pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Combine two switch statements into one, convert a nebulous pointer to one
that is a bit more in keeping with the rest of the driver code and cleanup
some coding style. No change in functionality, just cosmetic changes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Combine two switch statements into one, convert a nebulous pointer to one
that is a bit more in keeping with the rest of the driver code and remove
some dead code (there are no 80003es2lan devices with fiber). No change in
functionality, just cosmetic changes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The majority of the e1000e code checks most function return values using a
test like 'if (ret_val)' or 'if (!ret_val)' but there are a few instances
of 'if (ret_val == 0)'. This patch converts the latter to the former for
consistency.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
warning: missing initializer
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When TX hang occurs e1000_dump prints TX ring, RX ring and Device registers.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing ITR code is broken and confusing, with lots of similarly-named
variables that do different things. Additionally, after the driver carefully
determines the optimal interrupt rate for the adapter, it then
ignores it and always writes a fixed, suboptimal value.
This patch refactors that code to make variable names more descriptive of
what they actually do, and then actually writes the calculated result to
the hardware.
Preliminary testing shows that netperf TCP_STREAM tests goes from ~918Mbps
to ~940Mbps, and TCP_RR goes from ~2k transactions/sec up to > 8k.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct spelling "packtetbuf_num" to "packetbuf_num" in
drivers/net/ethernet/intel/ixgbe/ixgbe_common.h
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Change copyright date to 2012 in the source files.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove jump to out label that was skipping over code to replace the
ack bit in the mailbox cache variable. This was causing driver mailbox
routines that poll for the PF to ack a message to time out which would
in turn cause all other mailbox messages to fail. Also replace the
mailbox cache variable message indication bit when a message is found
so that other functions that choose to poll for a mailbox message from
the PF won't miss it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Send message to system log when the VF requests another MAC filter
but there is no space left on the device for it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert E Garrett <robertX.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New year so bump the copyright date.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X520 family of network devices, with the 82599 chip, support a
small number of Intel-verified SFP+ modules on their NICs. To maintain
stability and quality, the current devices restrict untested 3rd party
SFP+ modules.
This patch introduces a module parameter for ixgbe to allow these untested
modules at the user's peril. It also includes a warning to the syslog
alerting users that the modules aren't supported, and results may
vary.
CC: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The generic lib.c file contains code relative to the various MACs, NVM and
Manageability supported by the driver. This patch splits the file into
three which are specific to those areas similar to how the PHY-specific
code is in phy.c and code specific to the 80003es2lan, 8257x, and ichX
MAC families are in their own files. The generic code that is applicable
to all MAC/PHY parts supported by the driver remains in netdev.c, param.c
and ethtool.c files. No change in functionality, just moving code
around for ease of maintenance, with some whitespace and other checkpatch
cleanups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
__er16flash() is not meant to be called directly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert the last instances of strncpy() to the preferred strlcpy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To ease searching for debug message strings, concatenate strings that span
multiple lines even if the resulting line exceeds 80 columns; these will
not cause checkpatch warnings.
Also, add '\n' and remove unnecessary '\r' from a few debug strings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting the Low Power Link Up (LPLU, a.k.a. reverse auto-negotiation)
on 82577/8278/82579, do not restart auto-negotiation if reset of the Phy is
blocked by the Manageability Engine.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During bi-directional stress on some 82566/82567 devices, some received
packets were dropped. Increasing the Receive Packet Buffer Allocation
resolves this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When going to Sx with an ICHx/PCH device, the default Low Power Link Up
(LPLU, a.k.a. reverse auto-negotiation) behavior should be whatever is set
in the NVM. However, the function e1000_suspend_workarounds_ich8lan()
called when going to Sx always enabled LPLU in all power states.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The workaround which toggles the LANPHYPC (LAN PHY Power Control) value bit
to force the MAC-Phy interconnect into PCIe mode from SMBus mode during
driver load and resume should always be done except if PHY resets are
blocked by the Manageability Engine (ME). Previously, the toggle was done
only if PHY resets are blocked and the ME was disabled.
The rest of the patch is just indentation changes as a consequence of the
updated workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Internal stress testing with jumbo frames shows the reliability of ICH9 and
ICH10D devices is improved in certain corner cases by disabling the Early
Receive feature. To reduce the performance impact caused by disabling this
feature, the packet buffer sizes and relevant flow control settings are
modified accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Otherwise (on sparc64):
drivers/net/ethernet/intel/e1000e/ethtool.c:657:3: error: implicit declaration of function 'vmalloc' [-Werror=implicit-function-declaration]
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82574/82583, there is a hardware bug which might cause a Tx hang when
the internal buffer is full. Setting this bit enables a hardware fix to
work around the issue.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code snippet is simply writing default values to the register which is
unnecessary since the values are programmed into the register by default.
There is a special case for 80003es2lan needing the Retransmit on Late
Collision bit set but that is also done in e1000_init_hw_80003es2lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the default hardware values for TIPG except for 80003es2lan(*). The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs). The only change in
functionality is setting the correct default TIPG for the latter devices.
(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When connected to certain switches, the 82579 PHY might drop link
unexpectedly. Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware erratum workaround where the TXDCTL register must be the same
setting for both queues should always be done.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on a patch from Prabhakar Kushwaha <prabhakar@freescale.com>, set
appropriate default interrupt mode dependent on whether CONFIG_PCI_MSI
is enabled in the kernel configuration and if the hardware supports
MSI-X. Set the module parameter log message accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make it more like how igb does it, with some additional error checking.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations. Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable RPS by default. Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.
v2: added ethtool command to query flow hashing behavior per Ben Hutchings
and changed the type of rsskey to cleanup the setting of the register
array and avoid unnecessary casts (as pointed out by Joe Perches).
The long error messages are not changed since there is nothing in
the kernel ./Documentation that suggests the preferred method for
dealing with long messages other than to never break strings; leaving
them as-is for now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
e1000_rx_checksum() instead of in each call to the function
v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The arrays of function pointers should be const to make life harder
for rootkits.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes sparse warnings:
drivers/net/ethernet/intel/ixgbevf/vf.c:418:21: warning: symbol 'ixgbevf_82599_vf_info' was not declared. Should it be static?
drivers/net/ethernet/intel/ixgbevf/vf.c:423:21: warning: symbol 'ixgbevf_X540_vf_info' was not declared. Should it be static?
drivers/net/ethernet/intel/ixgbevf/mbx.c:331:29: warning: symbol 'ixgbevf_mbx_ops' was not declared. Should it be static?
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mailbox interrupt routine might cause a race condition sometimes
and cause a message to be missed.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is meant to address possible issues with the IXGBE register
defines generating incorrect values when given a complex expression for the
register offset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This irq disable/enable pair used to wrap access to the driver's vlgrp
struct, which is no longer present. So, then, this could also so no longer
be present.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cast and comment are unnecessary in the current upstream kernel.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Garrett, RobertX E <robertx.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse caught two functions that were only being used in one file.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements support for ndo_get_fcoe_hbainfo()
call in the ixgbe driver.
This function will be called by the FCoE protocol stack to
obtain device specific information from the underlying
device configured to do FCoE.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to 82576_Datasheet.pdf, PHY setting is lost after PHY power down.
So resetting PHY is needed when recovering from PHY power down to set a default
setting to PHY register.
Owing to this lack, NIC doesn't link up in some rare situation.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the runtime power management framework to add basic runtime PM support
to the igb driver. Namely, make the driver suspend the device when the link
is off and set it up for generating a wakeup event after the link has been
detected again. This feature is disabled by default.
Based on e1000e's runtime PM code.
Changes since v1:
Don't suspend the device when shutting down the interface.
Avoid race between runtime suspending and ethtool operations.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for byte queue limits (BQL)
Since this driver collects bytes count in 'bytecount' field, use it also
in igb_tx_map()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A global variable is currently used to hold the virtual address of the
CE4100 MDIO base register address. Store the address in the e1000_hw
structure and update macros accordingly.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not unmapping ce4100_gbe_mdio_base_virt in exit path in case
we are running on a CE4100 adapter, fix that.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Steven Rostedt, e1000 has a lockdep splat added
during the recent merge window. The issue is that
cancel_delayed_work is called while holding our private mutex.
There is no reason that I can see to hold the mutex during pci
shutdown, it was more just paranoia that I put the mutex_lock
around the call to e1000_down.
In a quick survey lots of drivers handle locking differently when
being called by the pci layer. The assumption here is that we
don't need the mutexes' protection in this function because
the driver could not be unloaded while in the shutdown handler
which is only called at reboot or poweroff.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device uses an already existing DevID but since it supports
WoL we need to add the Sub DevID. It's support of WoL is limited
to the first port.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Support for new 82599 based quad port adapter.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I2C access is timing critical. Always do a write flush after writing
to the I2CCTL register.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Saw typo in one message, so decided to run spell checker.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some register reads that had the opcode and register parameters swapped.
Also use define instead of a magic (0x3) number.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added pause flag for bi-directional flow control advertising to ethtool
settings.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to address possible issues with the IXGBEVF register
defines generating incorrect values when given a complex expression for the
register offset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transitioning through an IEEE DCBX version from a CEE DCBX
and back (CEE->IEEE->CEE) may leave IEEE attributes programmed
in the hardware. DCB uses a bit field in the set routines to
determine which attributes PG, PFC, APP need to be reprogrammed.
This is needed because user flow allows queueing a series
of changes and then reprogramming the hardware with the
entire set in one operation.
When transitioning from IEEE DCBX mode back into CEE DCBX
mode the PG and PFC bits need to be set so the possibly
different CEE attributes get programmed into the device.
This patch fixes broken logic that was evaluating to 0
and never setting any bits. Further this removes some
checks for num_tc in set routines. This logic only worked
when the number of traffic classes and user priorities
were equal. This is no longer the case for X540 devices.
Besides we can trust user input in this case if the
device is incorrectly configured the DCB bandwidths will
be incorrectly mapped but no OOPs, BUG, or hardware
failure will occur.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The order of operations is important in DCBnl set_all(). When FCoE
is configured it uses the up2tc map to learn which queues to configure
the hardware offloads on. Therefore we need to setup the map before
configuring FCoE.
This is only seen when the both up2tc mappings and APP info are
configured simultaneously.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the DMA Coalescing feature parameters to account for
larger MTUs. Previously, sufficient space may not have been allocated in
the receive buffer, causing packet drop.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on a patch from Mike McElroy created against the out-of-tree e1000e
driver:
Hitting the BUG_ON in napi_enable(). Code inspection shows that this can
only be triggered by calling napi_enable() twice without an intervening
napi_disable().
I saw the following sequence of events in the stack trace:
1) We simulated a cable pull using an Extreme switch.
2) e1000_tx_timeout() was entered.
3) e1000_reset_task() was called. Saw the message from e_err() in the
console log.
4) e1000_reinit_locked was called. This function calls e1000_down() and
e1000_up(). These functions call napi_disable() and napi_enable()
respectively.
5) Then on another thread, a monitor task saw carrier was down and executed
'ip set link down' and 'ip set link up' commands.
6) Saw the '_E1000_RESETTING'warning fron the e1000_close function.
7) Either the e1000_open() executed between the e1000_down() and e1000_up()
calls in step 4 or the e1000_open() call executed after the e1000_up()
call. In either case, napi_enable() is called twice which triggers the
BUG_ON.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Mike McElroy <mike.mcelroy@stratus.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch submitted my Michael Wang
<wangyun@linux.vnet.ibm.com>.
Descriptors may not be write-back while checking TX hang with flag
FLAG2_DMA_BURST on.
So when we detect hang, we just flush the descriptor and detect
again for once.
-v2 change 1 to true and 0 to false and remove extra ()
CC: Michael Wang <wangyun@linux.vnet.ibm.com>
CC: Flavio Leitner <fbl@redhat.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes to e1000e to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given we dont use anymore the struct net_device *dev argument, and this
interface brings litle benefit, remove netdev_{alloc|free}_page(), to
debloat include/linux/skbuff.h a bit.
(Some drivers used a mix of these interfaces and alloc_pages())
When allocating a page given to device for DMA transfer (device to
memory), it makes sense to use a cold one (__GFP_COLD)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert some remaining straglers' .get_drvinfo routines to use strlcpy
rather than strcpy/strncpy.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal #defines not module specific ones.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
printks should use KERN_ levels.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on original patch from Joe Perches <joe@perches.com>
Use the current logging styles.
pr_<level> conversions are now prefixed with "igb: "
Correct a defect where the trailing NTU may have been printed
on a separate line because of an interleaving hex_dump.
Remove unnecessary uses of KERN_CONT and use single pr_info()s
to avoid any possible output interleaving from other modules.
Coalesce formats as appropriate.
-v2 fix-up to make checkpatch.pl compliant and remove change to
the copyright line
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Based on the original patch from Joe Perches <joe@perches.com>
Use the current logging styles, prefix output with "ixgbevf: "
Add #define pr_fmt
Coalesce formats.
-v2 Fix-up to make checkpatch.pl compliant and remove change to
copyright line
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Based on the previous patch from Joe Perches <joe@perches.com>
Use current logging styles.
Prefix all output via #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Neaten link status dev_info.
-v2 Remove Copyright changes and fix-up patch to make it checkpatch.pl
compliant.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Previously the driver would force link without checking whether the link was
already established. This caused some inconsistencies in the LED blink rate.
Do not force link if link is already up.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch from Joe Perches.
Use the current logging styles.
pr_<level> conversions are now prefixed with "e1000e:"
Correct a couple of defects where the trailing NTU may have
been printed on a separate line because of an interleaving
hex_dump.
Remove unnecessary uses of KERN_CONT and use single pr_info()s
to avoid any possible output interleaving from other modules.
Coalesce formats as appropriate.
Remove an extra space from a broken across lines
coalescing of "Link Status " and " Change".
-v2 Remove changes to Copyright string
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Commit afc4b13d (net: remove use of ndo_set_multicast_list in
drivers) changed e1000e to use the ndo_set_rx_mode entry point,
but didn't implement the unicast address programming
functionality. Implement it to achieve the ability to add unicast
addresses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This round of floor sweeping converts strncpy calls in various .get_drvinfo
routines to the preferred strlcpy. It also does a modicum of other
cleaning in those routines.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform another round of floor sweeping, converting the .get_drvinfo
routines of additional drivers from strcpy to strlcpy along with
some conversion of sprintf to snprintf.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
Fix compiler errors and warnings with CONFIG_PCI_IOV defined and not
defined.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.
Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.
Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning the max traffic classes on get requests simplifies
user space configurations because applications will know
explicitly how many traffic classes can be used.
Typical switch implementations use 2 or 3 traffic classes
so this not seen often today. And user space can learn
the number of traffic classes by return codes but this
allows user space to configure ixgbe correctly at the
start.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Danny Kukawka