Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.
To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:
sys/
`-- power
`-- db1x
|-- gpio0
|-- gpio1
|-- gpio2
|-- gpio3
|-- gpio4
|-- gpio5
|-- gpio6
|-- gpio7
|-- timer
|-- timer_timeout
|-- wakemsk
`-- wakesrc
The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1'
enables a wakesource, 0 disables it.
The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.
The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.
For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:
echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep
This patch also removes the homebrew CPU frequency switching code. I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/alchemy/devboards/pm.c
Implement suspend/resume for DBDMA controller and its channels.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Au1550/Au1200 have a different memory controller which requires additi-
onal code to properly put memory to sleep (code taken from AMD/RMI's
Linux-2.6.11 source package).
Also fix up the remaining pm-related paths to compile on Au1200/Au1550
platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that nothing in time.c depends on calc_clock, it can
be moved to clocks.c where it belongs.
While at it, give it a better non-generic name and call it
as soon as possible in plat_mem_init.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device. As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.
If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the cpu_table:
- move detection of whether c0_config[OD] is read-only and should be set
to fix various chip errata to au1000 headers.
- move detection of write-only sys_cpupll to au1000 headers.
- remove the BCLK switching code: Activation of this features should be
left to the boards using the chips since it also affects external devices
tied to BCLK, and only the board designers know whether it is safe to
enable.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/cputable.c
There are no in-tree users, so remove them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch attempts to modernize core Alchemy interrupt handling code.
- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
the remaining (gpio-based) interrupt sources; update all boards
accordingly.
Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
Not every alchemy-based board might want these options forced on it,
and most of this stuff seems to be intended for devboard code anyway.
Remove commandline mangling code out of common chip code and instead
add relevant sections to all in-tree boards to not change existing
behaviour.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This should ease sharing of common devboard code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since memsize is unsigned, it would seem better to use strict_strtoul that
strict_strtol.
A simplified version of the semantic patch that makes this change is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@s2@
long e;
position p;
@@
strict_strtol@p(...,&e)
@@
position p != s2.p;
type T;
T e;
@@
- strict_strtol@p
+ strict_strtoul
(...,&e)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add au1xmmc platform data for PB1200/DB1200 boards and wire up the 2 SD
controllers for them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss